UniPhier SoCs contain AIDET (ARM Interrupt Detector). This is intended
to provide additional features that are not covered by GIC. The main
purpose is to provide logic inverter to support low level and falling
edge trigger types for interrupt lines from on-board devices.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The Marvell ICU unit is found in the CP110 block of the Marvell Armada
7K and 8K SoCs. It collects the wired interrupts of the devices located
in the CP110 and turns them into SPI interrupts in the GIC located in
the AP806 side of the SoC, by using a memory transaction.
Until now, the ICU was configured in a static fashion by the firmware,
and Linux was relying on this static configuration. By having Linux
configure the ICU, we are more flexible, and we can allocate dynamically
the GIC SPI interrupts only for devices that are actually in use.
The driver was initially written by Hanna Hawa <hannah@marvell.com>.
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This commit adds a simple driver for the Marvell GICP, a hardware unit
that converts memory writes into GIC SPI interrupts. The driver provides
a number of functions to the ICU driver to allocate GICP interrupts, and
get the physical addresses that the ICUs should write to to set/clear
interrupts.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The Aspeed 24XX/25XX chips share a single hardware interrupt across 14
separate I2C busses. This adds a dummy irqchip which maps the single
hardware interrupt to software interrupts for each of the busses.
Signed-off-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
In Mediatek SOCs, the CIRQ is a low power interrupt controller
designed to works outside MCUSYS which comprises with Cortex-Ax
cores,CCI and GIC.
The CIRQ controller is integrated in between MCUSYS( include
Cortex-Ax, CCI and GIC ) and interrupt sources as the second
level interrupt controller. The external interrupts which outside
MCUSYS will feed through CIRQ then bypass to GIC. CIRQ can monitors
all edge trigger interupts. When an edge interrupt is triggered,
CIRQ can record the status and generate a pulse signal to GIC when
flush command executed.
When system enters sleep mode, MCUSYS will be turned off to improve
power consumption, also GIC is power down. The edge trigger interrupts
will be lost in this scenario without CIRQ.
This commit provides the CIRQ irqchip implement.
Signed-off-by: Youlin Pei <youlin.pei@mediatek.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The Moxa Art interrupt controller is very very likely just an instance
of the Faraday FTINTC010 interrupt controller from Faraday Technology.
An indication would be its close association with the FA526 ARM core
and the fact that the register layout is the same.
The implementation in irq-moxart.c can probably be right off replaced
with the irq-ftintc010.c driver by adding a compatible string, selecting
this irqchip from the machine and run.
As a bonus we have an irqchip driver supporting high/low and
rising/falling edges for the Moxa Art, and shared code with the Gemini
platform.
Acked-by: Olof Johansson <olof@lixom.net>
Tested-by: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The Gemini irqchip turns out to be a standard IP component from
Faraday Technology named FTINTC010 after some research and new
information.
- Rename the driver and all symbols to reflect the new information.
- Add the new compatible string "faraday,ftintc010"
- Create a Kconfig symbol CONFIG_FARADAY_FTINTC010 so that SoCs
using this interrupt controller can easily select and reuse it
instead of hardwiring it to ARCH_GEMINI
I have created a separate patch to select the new Kconfig symbol
from the Gemini machine, which will be merged through the ARM
SoC tree.
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Paulius Zaleckas <paulius.zaleckas@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
As a part of transitioning the Gemini platform to device tree we
create this clean, device-tree-only irqchip driver.
Cc: Janos Laube <janos.dev@gmail.com>
Cc: Paulius Zaleckas <paulius.zaleckas@gmail.com>
Cc: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Driver for interrupt combiners in the Top-level Control and Status
Registers (TCSR) hardware block in Qualcomm Technologies chips.
An interrupt combiner in this block combines a set of interrupts by
OR'ing the individual interrupt signals into a summary interrupt
signal routed to a parent interrupt controller, and provides read-
only, 32-bit registers to query the status of individual interrupts.
The status bit for IRQ n is bit (n % 32) within register (n / 32)
of the given combiner. Thus, each combiner can be described as a set
of register offsets and the number of IRQs managed.
Signed-off-by: Agustin Vega-Frias <agustinv@codeaurora.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The Xilinx AXI Interrupt Controller IP block is used by the MIPS
based xilfpga platform and a few PowerPC based platforms.
Move the interrupt controller code out of arch/microblaze so that
it can be used by everyone
Tested-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The cleanups for v4.9 are a little larger that usual, but thankfully
that is almost exclusively due to removing a significant number of
files that have become obsolete after the still ongoing conversion
of old board files to devicetree.
- for mach-omap2, which is still the largest platform in arch/arm/,
the conversion to DT is finally complete after the Nokia N900 is
now fully supported there, along with the omap3 LDP, and we can
remove those two board files.
If no regressions are found, another large cleanup for the platform
will happen as a follow-up, removing dead code and restructuring
the platform based on being DT-only.
- In mach-imx, similar work is ongoing, but has not come that far.
This time, we remove the obsolete board file for the i.MX1
generation, which like i.MX25, i.MX5, i.MX6, and i.MX7 is now DT-only.
The remaining board files are for i.MX2 and i.MX3 machines
based on old ARM926 or ARM1136 cores that should work with DT
in principle.
- realview has just been converted from board files to DT, and a lot
of code gets removed in the process. This is the last
ARM/Keil/Versatile derived platform that was still using board
files, the other ones being integrator, versatile and vexpress.
We can probably merge the remaining code into a single directory
in the near future.
- clps711x had completed the conversion in v4.8, but we accidentally
left the files in place that should have been deleted then.
Conflicts: two files deleted here have been modified upstream,
the changes can be discarded.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=WaLy
-----END PGP SIGNATURE-----
Merge tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Arnd Bergmann:
"The cleanups for v4.9 are a little larger that usual, but thankfully
that is almost exclusively due to removing a significant number of
files that have become obsolete after the still ongoing conversion of
old board files to devicetree.
- for mach-omap2, which is still the largest platform in arch/arm/,
the conversion to DT is finally complete after the Nokia N900 is
now fully supported there, along with the omap3 LDP, and we can
remove those two board files. If no regressions are found, another
large cleanup for the platform will happen as a follow-up, removing
dead code and restructuring the platform based on being DT-only.
- In mach-imx, similar work is ongoing, but has not come that far.
This time, we remove the obsolete board file for the i.MX1
generation, which like i.MX25, i.MX5, i.MX6, and i.MX7 is now
DT-only. The remaining board files are for i.MX2 and i.MX3 machines
based on old ARM926 or ARM1136 cores that should work with DT in
principle.
- realview has just been converted from board files to DT, and a lot
of code gets removed in the process. This is the last
ARM/Keil/Versatile derived platform that was still using board
files, the other ones being integrator, versatile and vexpress. We
can probably merge the remaining code into a single directory in
the near future.
- clps711x had completed the conversion in v4.8, but we accidentally
left the files in place that should have been deleted then"
* tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (21 commits)
ARM: select PCI_DOMAINS config from ARCH_MULTIPLATFORM
ARM: stop *MIGHT_HAVE_PCI* config from being selected redundantly
ARM: imx: (trivial) fix typo and grammar
ARM: clps711x: remove extraneous files
ARM: imx: use IS_ENABLED() instead of checking for built-in or module
ARM: OMAP2+: use IS_ENABLED() instead of checking for built-in or module
ARM: OMAP1: use IS_ENABLED() instead of checking for built-in or module
ARM: imx: remove platform-mxc_rnga
ARM: realview: imply device tree boot
ARM: realview: no need to select SMP_ON_UP explicitly
ARM: realview: delete the RealView board files
ARM: imx: no need to select SMP_ON_UP explicitly
ARM: i.MX: Move SOC_IMX1 into 'Device tree only'
ARM: i.MX: Remove i.MX1 non-DT support
ARM: i.MX: Remove i.MX1 Synertronixx SCB9328 board support
ARM: i.MX: Remove i.MX1 Armadeus APF9328 board support
ARM: mxs: remove obsolete startup code for TX28
ARM: i.MX31 iomux: remove duplicates with alternate name
ARM: i.MX31 iomux: remove plain duplicates
ARM: OMAP2+: Drop legacy board file for LDP
...
The STM32 external interrupt controller consists of edge detectors that
generate interrupts requests or wake-up events.
Each line can be independently configured as interrupt or wake-up source,
and triggers either on rising, falling or both edges. Each line can also
be masked independently.
Originally-from: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: devicetree@vger.kernel.org
Cc: Daniel Thompson <daniel.thompson@linaro.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: arnd@arndb.de
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: bruherrera@gmail.com
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-gpio@vger.kernel.org
Cc: Rob Herring <robh+dt@kernel.org>
Cc: lee.jones@linaro.org
Cc: linux-arm-kernel@lists.infradead.org
Link: http://lkml.kernel.org/r/1474387259-18926-3-git-send-email-alexandre.torgue@st.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The Marvell Armada 7K/8K integrates a secondary interrupt controller
very originally named "PIC". It is connected to the main GIC via a
PPI. Amongst other things, this PIC is used for the ARM PMU.
This commit adds a simple irqchip driver for this interrupt
controller. Since this interrupt controller is not needed early at boot
time, we make the driver a proper platform driver rather than use the
IRQCHIP_DECLARE() mechanism.
Signed-off-by: Yehuda Yitschak <yehuday@marvell.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Link: https://lkml.kernel.org/r/1470408921-447-3-git-send-email-thomas.petazzoni@free-electrons.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This reduces the Kconfig for the RealView by assuming we are
always booting from the device tree, and removing all the uses
of CONFIG_REALVIEW_DT and replacing with CONFIG_ARCH_REALVIEW.
Further:
- Drop REALVIEW_HIGH_PHYS_OFFSET: we don't use this with device
tree.
- Drop the REALVIEW_EB_ARM11MP_REVB option: we now handle this
by simply using another device tree.
- Drop the PB1176 secure flash option: this is defined in the
PB1176 device tree but marked as "disabled", so users who
want to use it can simply enable it in the device tree and
go hacking around.
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There are two versions of the J-Core interrupt controller in use, aic1
which generates interrupts with programmable priorities, but only
supports 8 irq lines and maps them to cpu traps in the range 17 to 24,
and aic2 which uses traps in the range 64-127 and supports up to 128
irqs, with priorities dependent on the interrupt number. The Linux
driver does not make use of priorities anyway.
For simplicity, there is no aic1-specific logic in the driver beyond
setting the priority register, which is necessary for interrupts to
work at all. Eventually aic1 will likely be phased out, but it's
currently in use in deployments and all released bitstream binaries.
Signed-off-by: Rich Felker <dalias@libc.org>
Link: https://lkml.kernel.org/r/c3b89ef74aaa6477575dbe2d410eb1d182503243.147018b6529.git.dalias@libc.org
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Add a platform driver to support non-root GICs that require runtime
power-management. Currently, only non-root GICs are supported because
the functions, smp_cross_call() and set_handle_irq(), that need to
be called for a root controller are located in the __init section and
so cannot be called by the platform driver.
The GIC platform driver re-uses many functions from the existing GIC
driver including some functions to save and restore the GIC context
during power transitions. The functions for saving and restoring the
GIC context are currently only defined if CONFIG_CPU_PM is enabled and
to ensure that these functions are always defined when the platform
driver is enabled, a dependency on CONFIG_ARM_GIC_PM (which selects the
platform driver) has been added.
In order to re-use the private GIC initialisation code, a new public
function, gic_of_init_child(), has been added which calls various
private functions to initialise the GIC. This is different from the
existing gic_of_init() because it only supports non-root GICs (ie. does
not call smp_cross_call() is set_handle_irq()) and is not located in
the __init section (so can be used by platform drivers). Furthermore,
gic_of_init_child() dynamically allocates memory for the GIC chip data
which is also different from gic_of_init().
There is no specific suspend handling for GICs registered as platform
devices. Non-wakeup interrupts will be disabled by the kernel during
late suspend, however, this alone will not power down the GIC if
interrupts have been requested and not freed. Therefore, requestors of
non-wakeup interrupts will need to free them on entering suspend in
order to power-down the GIC.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
- Support for EZChip (now Mellanox) NPS-400 Network processor based on ARC700
http://www.mellanox.com/related-docs/prod_npu/PB_NPS-400.pdf
- NPS interrupt controller and clocksource drivers
- ARC timers probed off DT
- ARC iqrchips switching to linear domain (upgrade from legacy domains)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=pnAx
-----END PGP SIGNATURE-----
Merge tag 'arc-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC updates from Vineet Gupta:
"We have a relatively big changeset for ARC for 4.7.
The highlight is support for EZChip (now Mellanox) NPS-400 network
processor, a 400-Gb throughput C-programmable packet processor based
on ARC700 cores from Synopsys. See
http://www.mellanox.com/related-docs/prod_npu/PB_NPS-400.pdf
Also present are irqchip and clocksource drivers for NPS as agreed
with respective maintainers to go via ARC tree due to an soc header
dependency. I have the needed ACKs from Jason, Marc, Daniel. You
might run into a trivial merge conflict in drivers/irqchip/*
This EZChip platform support required some deep changes in ARC
architecture code and also opportunity to cleanup past sins (legacy
irq domains, missing irq domain lookup, hard coded timer irqs...)
Summary:
- Support for EZChip (now Mellanox) NPS-400 Network processor based
on ARC700
- NPS interrupt controller and clocksource drivers
- ARC timers probed off DT
- ARC iqrchips switching to linear domain (upgrade from legacy
domains)"
* tag 'arc-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc: (37 commits)
arc: axs103_smp: Fix CPU frequency to 100MHz for dual-core
arc: axs10x: Add DT bindings for I2S PLL Clock
ARC: pae: STRICT_MM_TYPECHECKS was broken
ARC: Add eznps platform to Kconfig and Makefile
ARC: [plat-eznps] Use dedicated COMMAND_LINE_SIZE
ARC: [plat-eznps] Use dedicated cpu_relax()
ARC: [plat-eznps] Use dedicated identity auxiliary register.
ARC: [plat-eznps] Use dedicated SMP barriers
ARC: [plat-eznps] Use dedicated atomic/bitops/cmpxchg
ARC: [plat-eznps] Use dedicated user stack top
ARC: [plat-eznps] Add eznps platform
ARC: [plat-eznps] Add eznps board defconfig and dts
ARC: Mark secondary cpu online only after all HW setup is done
ARC: rwlock: disable interrupts in !LLSC variant
ARC: Make vmalloc size configurable
ARC: clean out UAPI byteorder.h clean off Kconfig symbol
irqchip: add nps Internal and external irqchips
clocksource: Add NPS400 timers driver
soc: Support for EZchip SoC
Documentation: Add EZchip vendor to binding list
...
The change adds improved support of NXP LPC32xx MIC, SIC1 and SIC2
interrupt controllers.
This is a list of new features in comparison to the legacy driver:
* irq types are taken from device tree settings, no more need to
hardcode them,
* old driver is based on irq_domain_add_legacy, which causes problems
with handling MIC hardware interrupt 0 produced by SIC1,
* there is one driver for MIC, SIC1 and SIC2, no more need to handle
them separately, e.g. have two separate handlers for SIC1 and SIC2,
* the driver does not have any dependencies on hardcoded register
offsets,
* the driver is much simpler for maintenance,
* SPARSE_IRQS option is supported.
Legacy LPC32xx interrupt controller driver was broken since commit
76ba59f836 ("genirq: Add irq_domain-aware core IRQ handler"), which
requires a private interrupt handler, otherwise any SIC1 generated
interrupt (mapped to MIC hwirq 0) breaks the kernel with the message
"unexpected IRQ trap at vector 00".
The change disables compilation of a legacy driver found at
arch/arm/mach-lpc32xx/irq.c, the file will be removed in a separate
commit.
Fixes: 76ba59f836 ("genirq: Add irq_domain-aware core IRQ handler")
Tested-by: Sylvain Lemieux <slemieux.tyco@gmail.com>
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Adding EZchip NPS400 support.
Internal interrupts are handled by Multi Thread Manager (MTM)
Once interrupt is serviced MTM is acked for deactivating the interrupt.
External interrupts are handled by MTM as well as at Global Interrupt
Controller (GIC) e.g. serial and network devices.
Signed-off-by: Noam Camus <noamc@ezchip.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Vineet Gupta <vgupta@synopsys.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Some kind of Freescale Layerscape SoC provides a MSI
implementation which uses two SCFG registers MSIIR and
MSIR to support 32 MSI interrupts for each PCIe controller.
The patch is to support it.
Signed-off-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Tested-by: Alexander Stein <alexander.stein@systec-electronic.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
We've unfortunately started seeing a situation where percpu interrupts
are partitioned in the system: one arbitrary set of CPUs has an
interrupt connected to a type of device, while another disjoint
set of CPUs has the same interrupt connected to another type of device.
This makes it impossible to have a device driver requesting this interrupt
using the current percpu-interrupt abstraction, as the same interrupt number
is now potentially claimed by at least two drivers, and we forbid interrupt
sharing on per-cpu interrupt.
A solution to this is to turn things upside down. Let's assume that our
system describes all the possible partitions for a given interrupt, and
give each of them a unique identifier. It is then possible to create
a namespace where the affinity identifier itself is a form of interrupt
number. At this point, it becomes easy to implement a set of partitions
as a cascaded irqchip, each affinity identifier being the HW irq.
This allows us to keep a number of nice properties:
- Each partition results in a separate percpu-interrupt (with a restrictied
affinity), which keeps drivers happy.
- Because the underlying interrupt is still per-cpu, the overhead of
the indirection can be kept pretty minimal.
- The core code can ignore most of that crap.
For that purpose, we implement a small library that deals with some of
the boilerplate code, relying on platform-specific drivers to provide
a description of the affinity sets and a set of callbacks.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: devicetree@vger.kernel.org
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Rob Herring <robh+dt@kernel.org>
Link: http://lkml.kernel.org/r/1460365075-7316-4-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch adds the Alpine MSIX interrupt controller driver.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Tsahee Zidenberg <tsahee@annapurnalabs.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
- mvebu:
- Add odmi driver for Marvell 7K/8K SoCs
- Replace driver-specific set_affinity with generic version
- mips:
- Move ath79 MISC and CPU drivers from arch/ code to irqchip/
- tango:
- Add support for Sigma Designs SMP8[67]xx ctrl
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=4dMI
-----END PGP SIGNATURE-----
Merge tag 'irqchip-core-4.6-2' of git://git.infradead.org/users/jcooper/linux into irq/core
Pull the second round of irqchip core changes for v4.6 from Jason Cooper:
- mvebu:
- Add odmi driver for Marvell 7K/8K SoCs
- Replace driver-specific set_affinity with generic version
- mips:
- Move ath79 MISC and CPU drivers from arch/ code to irqchip/
- tango:
- Add support for Sigma Designs SMP8[67]xx ctrl
- mvebu (armada-370-xp)
- MSI support
- Deconflict with mvebu's arm64 code
- ts4800
- Restrict when ts4800 driver can be built
- Make ts4800_ic_ops static const
- bcm2836: Drop superfluous memory barrier
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=Omn0
-----END PGP SIGNATURE-----
Merge tag 'irqchip-core-4.6' of git://git.infradead.org/users/jcooper/linux into irq/core
Pull irqchip core changes for v4.6 from Jason Cooper:
- mvebu (armada-370-xp)
- MSI support
- Deconflict with mvebu's arm64 code
- ts4800
- Restrict when ts4800 driver can be built
- Make ts4800_ic_ops static const
- bcm2836: Drop superfluous memory barrier
This commits adds a new irqchip driver that handles the ODMI
controller found on Marvell 7K/8K processors. The ODMI controller
provide MSI interrupt functionality to on-board peripherals, much like
the GIC-v2m.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/1455888883-5127-1-git-send-email-thomas.petazzoni@free-electrons.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This adds support for the secondary interrupt controller used in Sigma
Designs SMP86xx and SMP87xx chips.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/1453313237-18570-2-git-send-email-mans@mansr.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The driver stays the same but the initialization changes a bit.
For OF boards we now get the memory map from the OF node and use
a linear mapping instead of the legacy mapping. For legacy boards
we still use a legacy mapping and just pass down all the parameters
from the board init code.
Signed-off-by: Alban Bedel <albeu@free.fr>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/1453553867-27003-1-git-send-email-albeu@free.fr
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Instead of building the irq-armada-370-xp driver directly when
CONFIG_ARCH_MVEBU is enabled, this commit introduces an intermediate
CONFIG_ARMADA_370_XP_IRQ hidden Kconfig option.
This allows this option to select other interrupt-related Kconfig
options (which will be needed in follow-up commits) rather than having
such selects done from arch/arm/mach-<foo>/.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Link: https://lkml.kernel.org/r/1455115621-22846-2-git-send-email-thomas.petazzoni@free-electrons.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Add the BCM6345 interrupt controller based on the SMP-capable BCM7038
and the BCM3380 but with packed interrupt registers.
Add the BCM6345 interrupt controller to a list with the existing BCM7038
so that interrupts on CPU1 are not ignored.
Update the maintainers file list for BMIPS to include this driver.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: devicetree@vger.kernel.org
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: linux-mips@linux-mips.org
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Jonas Gorski <jogo@openwrt.org>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Rob Herring <robh@kernel.org>
Link: http://lkml.kernel.org/r/5651D176.6030908@simon.arlott.org.uk
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Pull MIPS updates from Ralf Baechle:
"This is the main pull request for MIPS for 4.5 plus some 4.4 fixes.
The executive summary:
- ATH79 platform improvments, use DT bindings for the ATH79 USB PHY.
- Avoid useless rebuilds for zboot.
- jz4780: Add NEMC, BCH and NAND device tree nodes
- Initial support for the MicroChip's DT platform. As all the device
drivers are missing this is still of limited use.
- Some Loongson3 cleanups.
- The unavoidable whitespace polishing.
- Reduce clock skew when synchronizing the CPU cycle counters on CPU
startup.
- Add MIPS R6 fixes.
- Lots of cleanups across arch/mips as fallout from KVM.
- Lots of minor fixes and changes for IEEE 754-2008 support to the
FPU emulator / fp-assist software.
- Minor Ralink, BCM47xx and bcm963xx platform support improvments.
- Support SMP on BCM63168"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (84 commits)
MIPS: zboot: Add support for serial debug using the PROM
MIPS: zboot: Avoid useless rebuilds
MIPS: BMIPS: Enable ARCH_WANT_OPTIONAL_GPIOLIB
MIPS: bcm63xx: nvram: Remove unused bcm63xx_nvram_get_psi_size() function
MIPS: bcm963xx: Update bcm_tag field image_sequence
MIPS: bcm963xx: Move extended flash address to bcm_tag header file
MIPS: bcm963xx: Move Broadcom BCM963xx image tag data structure
MIPS: bcm63xx: nvram: Use nvram structure definition from header file
MIPS: bcm963xx: Add Broadcom BCM963xx board nvram data structure
MAINTAINERS: Add KVM for MIPS entry
MIPS: KVM: Add missing newline to kvm_err()
MIPS: Move KVM specific opcodes into asm/inst.h
MIPS: KVM: Use cacheops.h definitions
MIPS: Break down cacheops.h definitions
MIPS: Use EXCCODE_ constants with set_except_vector()
MIPS: Update trap codes
MIPS: Move Cause.ExcCode trap codes to mipsregs.h
MIPS: KVM: Make kvm_mips_{init,exit}() static
MIPS: KVM: Refactor added offsetof()s
MIPS: KVM: Convert EXPORT_SYMBOL to _GPL
...
This adds support for the interrupt controller present on PIC32 class
devices. It handles all internal and external interrupts. This controller
exists outside of the CPU core and is the arbitrator of all interrupts
(including interrupts from the CPU itself) before they are presented to
the CPU.
The following features are supported:
- DT properties for EVIC and for devices/peripherals that use interrupt lines
- Persistent and non-persistent interrupt handling
- irqdomain and generic chip support
- Configuration of external interrupt edge polarity
Signed-off-by: Cristian Birsan <cristian.birsan@microchip.com>
Signed-off-by: Joshua Henderson <joshua.henderson@microchip.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12092/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This commit adds support for the TS-4800 interrupt controller. This
controller is instantiated in a companion FPGA, and multiplex interrupts
for other FPGA IPs.
As this component is external to the SoC, the SoC might need to reserve
pins, so this controller is implemented as a platform driver and doesn't
use the IRQCHIP_DECLARE construct.
Signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: kernel@savoirfairelinux.com
Link: http://lkml.kernel.org/r/1450728683-31416-2-git-send-email-damien.riegel@savoirfairelinux.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Pull the GIC related updates from Marc Zyngier:
"Not a lot this time (what a relief!), but an interesting series from
Linus Walleij coming out of his work converting the ARM RealView
platforms to DT, and a couple of mundane fixes."
Mbigen means Message Based Interrupt Generator(MBIGEN).
Its a kind of interrupt controller that collects
the interrupts from external devices and generate msi interrupt.
Mbigen is applied to reduce the number of wire connected interrupts.
As the peripherals increasing, the interrupts lines needed is
increasing much, especially on the Arm64 server SOC.
Therefore, the interrupt pin in GIC is not enough to cover so
many peripherals.
Mbigen is designed to fix this problem.
Mbigen chip locates in ITS or outside of ITS.
Mbigen chip hardware structure shows as below:
mbigen chip
|---------------------|-------------------|
mgn_node0 mgn_node1 mgn_node2
| |-------| |-------|------|
dev1 dev1 dev2 dev1 dev3 dev4
Each mbigen chip contains several mbigen nodes.
External devices can connect to mbigen node through wire connecting way.
Because a mbigen node only can support 128 interrupt maximum, depends
on the interrupt lines number of devices, a device can connects to one
more mbigen nodes.
Also, several different devices can connect to a same mbigen node.
When devices triggered interrupt,mbigen chip detects and collects
the interrupts and generates the MBI interrupts by writing the ITS
Translator register.
To simplify mbigen driver,I used a new conception--mbigen device.
Each mbigen device is initialized as a platform device.
Mbigen device presents the parts(register, pin definition etc.) in
mbigen chip corresponding to a peripheral device.
So from software view, the structure likes below
mbigen chip
|---------------------|-----------------|
mbigen device1 mbigen device2 mbigen device3
| | |
dev1 dev2 dev3
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Ma Jun <majun258@huawei.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The ARM RealView PB11MPCore reference design has some special
bits in a system controller register to set up the GIC in one
of three modes: legacy, new with DCC, new without DCC. The
register is also used to enable FIQ.
Since the platform will not boot unless this register is set
up to "new with DCC" mode, we need a special quirk to be
compiled-in for the RealView platforms.
If we find the right compatible string on the GIC TestChip,
we enable this quirk by looking up the system controller and
enabling the special bits.
We depend on the CONFIG_REALVIEW_DT Kconfig symbol as the old
boardfile code has the same fix hardcoded, and this is only
needed for the attempts to modernize the RealView code using
device tree.
After fixing this, the PB11MPCore boots with device tree
only.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Freescale iMX23/iMX28 and Alphascale ASM9260 have similar interrupt
collectors. We already prepared the mxs driver to handle a different
register layout. Add the actual ASM9260 support.
Differences between these devices:
- Different register offsets
- Different count of interupt lines per register
- ASM9260 does not provide reset bit
- ASM9260 does not support FIQ.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Tested-by: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: marc.zyngier@arm.com
Cc: jason@lakedaemon.net
Link: http://lkml.kernel.org/r/1444677334-12242-6-git-send-email-linux@rempel-privat.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
IMX7D contains a new version of GPC IP block (GPCv2). It has two major
functions: power management and wakeup source management.
When the system is in WFI (wait for interrupt) mode, the GPC block
will be the first block on the platform to be activated and signaled.
In normal wait mode during cpu idle, the system can be woken up by any
enabled interrupts. In standby or suspend mode, the system can only be
wokem up by the pre-defined wakeup sources.
Based-on-patch-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Shenwei Wang <shenwei.wang@freescale.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: <shawn.guo@linaro.org>
Cc: <jason@lakedaemon.net>
Link: http://lkml.kernel.org/r/1440443055-7291-1-git-send-email-shenwei.wang@freescale.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This interrupt controller is the new root interrupt controller with
the timer, PMU events, and IPIs, and the bcm2835's interrupt
controller is chained off of it to handle the peripherals.
I wrote the interrupt chip support, while Andrea Merello wrote the IPI
code.
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Cc: linux-rpi-kernel@lists.infradead.org
Cc: Lee Jones <lee@kernel.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: linux-arm-kernel@lists.infradead.org
Link: http://lkml.kernel.org/r/1438902033-31477-5-git-send-email-eric@anholt.net
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
In order to support non-PCI MSI with the GICv3 ITS, add the minimal
required entry points for the MSI domain (an msi_prepare implementation).
The rest is only boilerplate code to find the raw ITS domain.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: Yijing Wang <wangyijing@huawei.com>
Cc: Ma Jun <majun258@huawei.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Duc Dang <dhdang@apm.com>
Cc: Hanjun Guo <hanjun.guo@linaro.org>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Link: http://lkml.kernel.org/r/1438091186-10244-16-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
It is becoming obvious that having the PCI/MSI code in the same
file as the the core ITS code is giving people implementing non-PCI
MSI support the wrong kind of idea.
In order to make things a bit clearer, let's move the PCI/MSI code
out to its own file. Hopefully it will make it clear that whoever
thinks of hooking into the core ITS better have a very strong point.
We use a temporary entry point that will get removed in a subsequent
patch, once the proper infrastructure is added.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: Yijing Wang <wangyijing@huawei.com>
Cc: Ma Jun <majun258@huawei.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Duc Dang <dhdang@apm.com>
Cc: Hanjun Guo <hanjun.guo@linaro.org>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Link: http://lkml.kernel.org/r/1438091186-10244-12-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Pull MIPS updates from Ralf Baechle:
- Improvements to the tlb_dump code
- KVM fixes
- Add support for appended DTB
- Minor improvements to the R12000 support
- Minor improvements to the R12000 support
- Various platform improvments for BCM47xx
- The usual pile of minor cleanups
- A number of BPF fixes and improvments
- Some improvments to the support for R3000 and DECstations
- Some improvments to the ATH79 platform support
- A major patchset for the JZ4740 SOC adding support for the CI20 platform
- Add support for the Pistachio SOC
- Minor BMIPS/BCM63xx platform support improvments.
- Avoid "SYNC 0" as memory barrier when unlocking spinlocks
- Add support for the XWR-1750 board.
- Paul's __cpuinit/__cpuinitdata cleanups.
- New Malta CPU board support large memory so enable ZONE_DMA32.
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (131 commits)
MIPS: spinlock: Adjust arch_spin_lock back-off time
MIPS: asmmacro: Ensure 64-bit FP registers are used with MSA
MIPS: BCM47xx: Simplify handling SPROM revisions
MIPS: Cobalt Don't use module_init in non-modular MTD registration.
MIPS: BCM47xx: Move NVRAM driver to the drivers/firmware/
MIPS: use for_each_sg()
MIPS: BCM47xx: Don't select BCMA_HOST_PCI
MIPS: BCM47xx: Add helper variable for storing NVRAM length
MIPS: IRQ/IP27: Move IRQ allocation API to platform code.
MIPS: Replace smp_mb with release barrier function in unlocks.
MIPS: i8259: DT support
MIPS: Malta: Basic DT plumbing
MIPS: include errno.h for ENODEV in mips-cm.h
MIPS: Define GCR_GIC_STATUS register fields
MIPS: BPF: Introduce BPF ASM helpers
MIPS: BPF: Use BPF register names to describe the ABI
MIPS: BPF: Move register definition to the BPF header
MIPS: net: BPF: Replace RSIZE with SZREG
MIPS: BPF: Free up some callee-saved registers
MIPS: Xtalk: Update xwidget.h with known Xtalk device numbers
...
Masahiro Yamada
Thomas Petazzoni
Brendan Higgins
Youlin Pei
Linus Walleij
Agustin Vega-Frias
Zubair Lutfullah Kakakhel
Linus Torvalds
Thomas Gleixner
Alexandre TORGUE
Jason Cooper
Rich Felker
Benjamin Herrenschmidt
Jon Hunter
Vladimir Zapolskiy
Noam Camus
Minghuan Lian
Marc Zyngier
Antoine Tenart
Mans Rullgard
Alban Bedel
Simon Arlott
Cristian Birsan
Damien Riegel
Ma Jun
Oleksij Rempel
Shenwei Wang
Eric Anholt
Ralf Baechle