Use Tegra pinconrol dt-binding macro to set the values of different pinmux
properties of Tegra114 platforms.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Use key code macros for all key code refernced for keys.
For tegra20-seaboard.dts and tegra20-harmony.dts:
The key comment for key (16th row and 1st column) is KEY_KPSLASH but
code is 0x004e which is the key code for KEY_KPPLUS. As there other
key exist with KY_KPPLUS, I am assuming key code is wrong and comment
is fine. With this assumption, I am keeping the key code as KEY_KPSLASH.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Subsequent patches will need to reference a PWM channel for backlight
support, so enable the PWM device and assign a label to it.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The PWM controller on Tegra124 is the same as the one on earlier SoC
generations.
Signed-off-by: Thierry Reding <treding@nvidia.com>
[swarren, added reset properties]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Venice2 uses the MAX98090 audio CODEC, and supports built-in speakers,
and a combo headphones/microphone jack. Add a top-level sound card node
to represent this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tegra124 contains a similar set of audio devices to previous Tegra chips.
Specifically, there is an AHUB device which contains DMA FIFOs and audio
routing, and which hosts various audio-related components such as I2S
controllers.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Enable all the I2C controllers that are wired up on Venice2. I don't
know the correct I2C bus clock rates, so set them all to a conservative
100KHz for now.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tegra124 has 6 I2C controllers. The first 5 have identical configuration
to Tegra114, but the sixth obviously has different interrupt/... IDs.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tegra124 has 4 MMC controllers just like previous versions of the SoC.
Note that there are some non-backwards-compatible HW differences, and
hence a new DT compatible value must be used to describe the HW.
Also enable the relevant controllers in the Venice2 board DT.
power-gpios property suggested by Thierry Reding.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Instantiate the APB DMA controller in the Tegra124 DT, and add all
DMA-related properties to other DT nodes that rely on (reference) the
DMA controller's node.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
The DT bindings now require module resets to be specified. The earlier
patches which added these nodes were originally written before that
requirement.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
This patch adds clock properties for devices in the DT for basic support
of Tegra124 SoC.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
[swarren, added missing unit address to "clock" node]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
For Tegra DT files, I've been attempting to keep the nodes sorted in
the order:
1) Nodes with reg, in order of reg.
2) Nodes without reg, alphabetically.
This patch fixes a few escapees that I missed:-(
The diffs look larger than they really are, because sometimes when one
node was moved up or down, diff chose to represent this as many other
nodes being moved the other way!
Signed-off-by: Stephen Warren <swarren@nvidia.com>
DT node names should include a unit address iff the node has a reg
property. For Tegra DTs at least, we were previously applying a different
rule, namely that node names only needed to include a unit address if it
was required to make the node name unique. Consequently, many unit
addresses are missing. Add them.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Now that all Tegra drivers have been converted to use DMA APIs which
retrieve DMA channel information from standard DMA DT properties, we can
remove all the legacy DT DMA-related properties.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Now that all Tegra drivers have been converted to use the common reset
framework, we can remove all the legacy DT clocks/clock-names entries for
"clocks" that were only used with the old custom Tegra module reset API.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Tegra's clock driver now provides an implementation of the common
reset API (include/linux/reset.h). Use this instead of the old Tegra-
specific API; that will soon be removed.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-By: Terje Bergstrom <tbergstrom@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
The Tegra clock driver is built unconditionally when Tegra support is
enabled. In order to avoid having to ifdef the forthcoming reset driver
implementation, have ARCH_TEGRA select RESET_CONTROLLER.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
This patch switches the Tegra DT files to use the standard DMA DT bindings
rather than custom properties. Note that the legacy properties are not yet
removed; the drivers must be updated to use the new properties first.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
An earlier patch updated the Tegra DT bindings to require resets and
reset-names properties to be filled in. This patch updates the DT files
to include those properties.
Note that any legacy clocks and clock-names entries that are replaced by
reset properties are not yet removed; the drivers must be updated to use
the new resets and reset-names properties first.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Many of the Tegra DT binding documents say nothing about the clocks or
clock-names properties, yet those are present and required in DT files.
This patch simply updates the documentation file to match the implicit
definition of the binding, based on real-world DT content.
All Tegra bindings that mention clocks are updated to have consistent
wording and formatting of the clock-related properties.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-By: Terje Bergstrom <tbergstrom@nvidia.com>
Pull x86 and EFI fixes from Peter Anvin:
"Half of these are EFI-related:
The by far biggest change is the change to hold off the deletion of a
sysfs entry while a backend scan is in progress. This is to avoid
calling kmemdup() while under a spinlock.
The other major change is for each entry in the EFI pstore backend to
get a unique identifier, as required by the pstore filesystem proper.
The other changes are:
A fix to the recent consolidation and optimization of using "asm goto"
with read-modify-write operation, which broke the bitops; specifically
in such a way that we could end up generating invalid code.
A build hack to make sure we compile with -mno-sse. icc, and most
likely future versions of gcc, can generate SSE instructions unless we
tell it not to.
A comment-only patch to a change the was due in part to an unpublished
erratum; now when the erratum is published we want to add a comment
explaining why"
* 'x86/urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/apic, doc: Justification for disabling IO APIC before Local APIC
x86, bitops: Correct the assembly constraints to testing bitops
x86-64, build: Always pass in -mno-sse
efi-pstore: Make efi-pstore return a unique id
x86/efi: Fix earlyprintk off-by-one bug
efivars, efi-pstore: Hold off deletion of sysfs entry until the scan is completed
Since erratum AVR31 in "Intel Atom Processor C2000 Product Family
Specification Update" is now published, I added a justification
comment for disabling IO APIC before Local APIC, as changed in commit:
522e664644 x86/apic: Disable I/O APIC before shutdown of the local APIC
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Link: http://lkml.kernel.org/r/1386202069-51515-1-git-send-email-fenghua.yu@intel.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
In checkin:
0c44c2d0f4 x86: Use asm goto to implement better modify_and_test() functions
the various functions which do modify and test were unified and
optimized using "asm goto". However, this change missed the detail
that the bitops require an "Ir" constraint rather than an "er"
constraint ("I" = integer constant from 0-31, "e" = signed 32-bit
integer constant). This would cause code to miscompile if these
functions were used on constant bit positions 32-255 and the build to
fail if used on constant bit positions above 255.
Add the constraints as a parameter to the GEN_BINARY_RMWcc() macro to
avoid this problem.
Reported-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/529E8719.4070202@zytor.com
Another batch of fixes for ARM SoCs for 3.13. The diffstat is large,
mostly because of:
- Another set of fixes to fix regressions caused by moving OMAP from board
files to DT. Tony thinks this was the last major set of fixes, with
maybe just a few small patches to follow.
- More fixes for Marvell platforms, most dealing with misdescribed PCIe
hardware, i.e. incorrect number of busses on some SoCs, etc. The line
delta adds up due to various ranges moving around when this is fixed.
But there's also:
- Some smaller tweaks to defconfigs to make more boards bootable in my
test setup for better coverage.
- There are also a few other smaller fixes, a short series for at91, a couple
of reverts for ux500, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=PljB
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Another batch of fixes for ARM SoCs for 3.13. The diffstat is large,
mostly because of:
- Another set of fixes to fix regressions caused by moving OMAP from
board files to DT. Tony thinks this was the last major set of
fixes, with maybe just a few small patches to follow.
- More fixes for Marvell platforms, most dealing with misdescribed
PCIe hardware, i.e. incorrect number of busses on some SoCs, etc.
The line delta adds up due to various ranges moving around when
this is fixed.
But there's also:
- Some smaller tweaks to defconfigs to make more boards bootable in
my test setup for better coverage.
- There are also a few other smaller fixes, a short series for at91,
a couple of reverts for ux500, etc"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (39 commits)
arm: dts: socfpga: Change some clocks of gate-clk type to perip-clk
arm: socfpga: Enable ARM_TWD for socfpga
ARM: multi_v7_defconfig: enable SDHCI_BCM_KONA and MMC_BLOCK_MINORS=16
ARM: sunxi_defconfig: enable NFS, TMPFS, PRINTK_TIME and nfsroot support
ARM: multi_v7_defconfig: enable network for BeagleBone Black
ARM: dts: Fix the name of supplies for smsc911x shared by OMAP
ARM: OMAP2+: Powerdomain: Fix unchecked dereference of arch_pwrdm
ARM: dts: omap3-beagle: Add omap-twl4030 audio support
ARM: dts: omap4-sdp: Fix pin muxing for wl12xx
ARM: dts: omap4-panda-common: Fix pin muxing for wl12xx
ARM: at91: fixed unresolved symbol "at91_pm_set_standby" when built without CONFIG_PM
ARM: at91: add usart3 alias to dtsi
ARM: at91: sama5d3: reduce TWI internal clock frequency
mmc: omap: Fix I2C dependency and make driver usable with device tree
mmc: omap: Fix DMA configuration to not rely on device id
ARM: dts: omap3-beagle: Fix USB host on beagle boards (for 3.13)
ARM: dts: omap3-igep0020: name twl4030 VPLL2 regulator as vdds_dsi
ARM: dts: AM33XX IGEP0033: add USB support
ARM: dts: AM33XX BASE0033: add 32KBit EEPROM support
ARM: dts: AM33XX BASE0033: add pinmux and user led support
...
Pull parsic updates from Helge Deller:
- a fix for the mmap(MAP_FIXED|MAP_SHARED) syscall to the same address
which was already given in a previous call (fixes locale-gen on
debian)
- change the memory layout of the kernel to avoid the need for the
-mlong-calls compiler option (depends on commit 5ecbe3c3c6 -
"kernel/extable: fix address-checks for core_kernel and init areas")
- defconfig updates, e.g. use the SIL680 driver instead of the SIIMAGE
driver
- add more parisc machine names to the machine database
* 'parisc-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: update 64bit defconfigs and use SIL680 instead of SIIMAGE driver
parisc: remove CONFIG_MLONGCALLS=y from defconfigs
parisc: fix kernel memory layout in vmlinux.ld.S
parisc: use kernel_text_address() in unwind functions
parisc: remove empty SERIAL_PORT_DFNS in serial.h
parisc: add some more machine names to hardware database
parisc: fix mmap(MAP_FIXED|MAP_SHARED) to already mmapped address
Pull crypto fixes from Herbert Xu:
"This push fixes a number of crashes triggered by a previous crypto
self-test update. It also fixes a build problem in the caam driver,
as well as a concurrency issue in s390.
Finally there is a pair of fixes to bugs in the crypto scatterwalk
code and authenc that may lead to crashes"
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: testmgr - fix sglen in test_aead for case 'dst != src'
crypto: talitos - fix aead sglen for case 'dst != src'
crypto: caam - fix aead sglen for case 'dst != src'
crypto: ccm - Fix handling of zero plaintext when computing mac
crypto: s390 - Fix aes-xts parameter corruption
crypto: talitos - corrrectly handle zero-length assoc data
crypto: scatterwalk - Set the chain pointer indication bit
crypto: authenc - Find proper IV address in ablkcipher callback
crypto: caam - Add missing Job Ring include
Pull timer fixes from Thomas Gleixner:
- timekeeping: Cure a subtle drift issue on GENERIC_TIME_VSYSCALL_OLD
- nohz: Make CONFIG_NO_HZ=n and nohz=off command line option behave the
same way. Fixes a long standing load accounting wreckage.
- clocksource/ARM: Kconfig update to avoid ARM=n wreckage
- clocksource/ARM: Fixlets for the AT91 and SH clocksource/clockevents
- Trivial documentation update and kzalloc conversion from akpms pile
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
nohz: Fix another inconsistency between CONFIG_NO_HZ=n and nohz=off
time: Fix 1ns/tick drift w/ GENERIC_TIME_VSYSCALL_OLD
clocksource: arm_arch_timer: Hide eventstream Kconfig on non-ARM
clocksource: sh_tmu: Add clk_prepare/unprepare support
clocksource: sh_tmu: Release clock when sh_tmu_register() fails
clocksource: sh_mtu2: Add clk_prepare/unprepare support
clocksource: sh_mtu2: Release clock when sh_mtu2_register() fails
ARM: at91: rm9200: switch back to clockevents_config_and_register
tick: Document tick_do_timer_cpu
timer: Convert kmalloc_node(...GFP_ZERO...) to kzalloc_node(...)
NOHZ: Check for nohz active instead of nohz enabled
Always pass in the -mno-sse argument, regardless if
-preferred-stack-boundary is supported. We never want to generate SSE
instructions in the kernel unless we *really* know what we're doing.
According to H. J. Lu, any version of gcc new enough that we support
it at all should handle the -mno-sse option, so just add it
unconditionally.
Reported-by: Kevin B. Smith <kevin.b.smith@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: H. J. Lu <hjl.tools@gmail.com>
Link: http://lkml.kernel.org/n/tip-j21wzqv790q834n7yc6g80j1@git.kernel.org
Cc: <stable@vger.kernel.org> # build fix only
Some of the clocks that were designated gate-clk do not have a gate, so
change those clocks to be of periph-clk type.
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Enable MMC/SD on the Broadcom mobile platforms, and increase the block
minors from the default 8 to 16 (since the Broadcom board by default
has root on the 8th partition).
Signed-off-by: Olof Johansson <olof@lixom.net>
Cc: stable@vger.kernel.org # v3.12
This enables a few more options on the sunxi defconfigs such that I can
use nfsroot to boot them (there is no local storage support yet). It
also enables PRINTK_TIME and tmpfs since it's a common distro requirement.
Signed-off-by: Olof Johansson <olof@lixom.net>
From Tony Lindgren:
Few more legacy booting vs device tree booting fixes that people
have noticed while booting things with device tree for things like
omap4 WLAN, smsc911x, and beagle audio. Hopefully this will be it
for the legacy booting vs device tree fixes for this -rc cycle.
* tag 'omap-for-v3.13/more-dt-regressions' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Fix the name of supplies for smsc911x shared by OMAP
ARM: OMAP2+: Powerdomain: Fix unchecked dereference of arch_pwrdm
ARM: dts: omap3-beagle: Add omap-twl4030 audio support
ARM: dts: omap4-sdp: Fix pin muxing for wl12xx
ARM: dts: omap4-panda-common: Fix pin muxing for wl12xx
BeagleBone Black uses the TI CPSW ethernet controller, enable it in the
multi_v7_defconfig for testing coverage purposes.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Tony Lindgren <tony@atomide.com>
Cc: stable@vger.kernel.org # v3.12
From Nicolas Ferre:
AT91: second round of fixes for 3.13
- reduce IP frequency for I2C on sama5d3
- missing aliases directive for USART3 on 9x5 family
- a PM symbol is missing if !CONFIG_PM
* tag 'at91-fixes' of git://github.com/at91linux/linux-at91:
ARM: at91: fixed unresolved symbol "at91_pm_set_standby" when built without CONFIG_PM
ARM: at91: add usart3 alias to dtsi
ARM: at91: sama5d3: reduce TWI internal clock frequency
From Jason Cooper, mvebu DT fixes for v3.13:
- mvebu
- PCIe fixes now that we have test devices with more ports.
- fix access to coherency registers
* tag 'mvebu-dt-fixes-3.13' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: re-enable PCIe on Armada 370 DB
ARM: mvebu: use the virtual CPU registers to access coherency registers
ARM: mvebu: fix second and third PCIe unit of Armada XP mv78260
ARM: mvebu: second PCIe unit of Armada XP mv78230 is only x1 capable
From Tony Lindgren:
Some omap related fixes that have come up with people moving to device
tree only based booting for omap2+.
The series contains a handful of fixes for the igep boards as they were
one of the first omap3 boards to jump over completely to device tree
based booting. So these can be considered regressions compared to
booting igep in legacy mode with board files in v3.12.
Also included are few other device tree vs legacy booting regressions:
- yet more missing omap3 .dtsi entries that have showed up booting
various boards with device tree only
- n900 eMMC device tree fix
- fixes for beagle USB EHCI
- two fixes to make omap2420 MMC work
As we're moving omap2+ to be device tree only for v3.14, I'd like to
have v3.13 work equally well for legacy based booting and device tree
based booting. So there will be likely few more device tree related
booting patches trickling in.
This series also includes a regression fix for the omap timer posted
mode that may wrongly stay on from the bootloader for some SoCs.
* tag 'omap-for-v3.13/fixes-against-rc1-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
mmc: omap: Fix I2C dependency and make driver usable with device tree
mmc: omap: Fix DMA configuration to not rely on device id
ARM: dts: omap3-beagle: Fix USB host on beagle boards (for 3.13)
ARM: dts: omap3-igep0020: name twl4030 VPLL2 regulator as vdds_dsi
ARM: dts: AM33XX IGEP0033: add USB support
ARM: dts: AM33XX BASE0033: add 32KBit EEPROM support
ARM: dts: AM33XX BASE0033: add pinmux and user led support
ARM: dts: AM33XX BASE0033: add pinmux and hdmi node to enable display
ARM: dts: omap3-igep0020: Add pinmuxing for DVI output
ARM: dts: omap3-igep0020: Add pinmux setup for i2c devices
ARM: dts: omap3-igep: Update to use the TI AM/DM37x processor
ARM: dts: omap3-igep: Add support for LBEE1USJYC WiFi connected to SDIO
ARM: dts: omap3-igep: Fix bus-width for mmc1
ARM: OMAP2+: dss-common: change IGEP's DVI DDC i2c bus
ARM: OMAP2+: Disable POSTED mode for errata i103 and i767
ARM: OMAP2+: Fix eMMC on n900 with device tree
ARM: OMAP2+: Add fixed regulator to omap2plus_defconfig
ARM: OMAP2+: Fix more missing data for omap3.dtsi file
Signed-off-by: Olof Johansson <olof@lixom.net>
drivers/net/ethernet/smsc/smsc911x.c is expecting supplies named
"vdd33a" and "vddvario". Currently the shared DTS file provides
"vmmc" and "vmmc_aux", and the supply lookup will fail:
smsc911x 2c000000.ethernet: Looking up vdd33a-supply from device tree
smsc911x 2c000000.ethernet: Looking up vdd33a-supply property in node /ocp/gpmc@6e000000/ethernet@gpmc failed
smsc911x 2c000000.ethernet: Looking up vddvario-supply from device tree
smsc911x 2c000000.ethernet: Looking up vddvario-supply property in node /ocp/gpmc@6e000000/ethernet@gpmc failed
Fix it!
Looks like commmit 6b2978ac40 (ARM: dts: Shared file for omap GPMC
connected smsc911x) made the problem more visible by moving the smc911x
configuration from the omap3-igep0020.dts file to the generic file.
But it seems we've had this problem since commit d72b441501
(ARM: dts: omap3-igep0020: Add SMSC911x LAN chip support).
Tested on OMAP3 Overo platform.
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
[tony@atomide.com: updated comments for the commits causing the problem]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 'cd8abed' "ARM: OMAP2+: Powerdomain: Remove the need to
always have a voltdm associated to a pwrdm" leads to the following
Smatch complaint:
arch/arm/mach-omap2/powerdomain.c:131 _pwrdm_register()
error: we previously assumed 'arch_pwrdm' could be null (see line 105)
So, fix the unchecked dereference of arch_pwrdm.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This adds typical McBSP2-TWL4030 audio description to the legacy
Beagle Board.
Signed-off-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Mux mode for wlan/sdmmc5 should be MODE0 in pinmux_wl12xx_pins and
Enable Pull up on sdmmc5_clk to detect SDIO card.
This fixes WLAN on omap4-sdp that got broken in v3.10 when we
moved omap4 to boot using device tree only as I did not have
the WL12XX card in my omap4 SDP to test with. The commit that
attempted to make WL12XX working on omap4 SDP was 775d2418f3
(ARM: dts: Fix muxing and regulator for wl12xx on the SDIO
bus for blaze).
Signed-off-by: Balaji T K <balajitk@ti.com>
[tony@atomide.com: updated comments for the regression]
Signed-off-by: Tony Lindgren <tony@atomide.com>
pin mux wl12xx_gpio and wl12xx_pins should be part of omap4_pmx_core
and not omap4_pmx_wkup. So, move wl12xx_* to omap4_pmx_core.
Fix the following error message:
pinctrl-single 4a31e040.pinmux: mux offset out of range: 0x38 (0x38)
pinctrl-single 4a31e040.pinmux: could not add functions for pinmux_wl12xx_pins 56x
SDIO card is not detected after moving pin mux to omap4_pmx_core since
sdmmc5_clk pull is disabled. Enable Pull up on sdmmc5_clk to detect SDIO card.
This fixes a regression where WLAN did not work after a warm reset
or after one up/down cycle that happened when we move omap4 to boot
using device tree only. For reference, the kernel bug is described at:
https://bugzilla.kernel.org/show_bug.cgi?id=63821
Cc: stable@vger.kernel.org # v3.10+
Signed-off-by: Balaji T K <balajitk@ti.com>
[tony@atomide.com: update comments to describe the regression]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Pull perf fixes from Ingo Molnar:
"Misc kernel and tooling fixes"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
tools lib traceevent: Fix conversion of pointer to integer of different size
perf/trace: Properly use u64 to hold event_id
perf: Remove fragile swevent hlist optimization
ftrace, perf: Avoid infinite event generation loop
tools lib traceevent: Fix use of multiple options in processing field
perf header: Fix possible memory leaks in process_group_desc()
perf header: Fix bogus group name
perf tools: Tag thread comm as overriden
- Fix lazy flushing in case m2p override fails.
- Fix module compile issues with ARM/Xen
- Add missing call to DMA map page for Xen SWIOTLB for ARM.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)
iQEcBAABAgAGBQJSnJuAAAoJEFjIrFwIi8fJj7sIAJQgSEMWJcEOBJ3lujfbhhKr
9GYfyNILfBjaOcH3LkA354U0JB3y4vON/xz6ONzMO4X7Jj6oUzACeEluq2iexlji
VDxqtnDJGS/82TcIN5xOVKRZbIqZ0xdRjK2f4h7AU9lIoIk+SJEJIycG1RGqqrmr
0nv39lUMjQhXNDhUjyt7e6JQj5GHrP0hzp5ngEQGcquPKbHXUInlwkB/kCH3zwju
2kEYQyKSWFoZCVtIBDeHplcZw9r/zWyOHBxjWOVoI/KZk8k+6d2breC3hv0lrhvU
qkJwzJcKZGlFdiCVHLbo3sTHf0NvvfF+qBCv7JbsymYaQc5SkrATmQ/DAUOssg0=
=emSu
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.13-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull Xen bug-fixes from Konrad Rzeszutek Wilk:
"Fixes to patches that went in this merge window along with a latent
bug:
- Fix lazy flushing in case m2p override fails.
- Fix module compile issues with ARM/Xen
- Add missing call to DMA map page for Xen SWIOTLB for ARM"
* tag 'stable/for-linus-3.13-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/gnttab: leave lazy MMU mode in the case of a m2p override failure
xen/arm: p2m_init and p2m_lock should be static
arm/xen: Export phys_to_mach to fix Xen module link errors
swiotlb-xen: add missing xen_dma_map_page call
If CONFIG_PM is not defined, then arch/arm/mach-at91/pm.c is not
compiled in. This patch creates an inline function that does nothing
if CONFIG_PM is not defined.
Signed-off-by: Brent Taylor <motobud@gmail.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Alias was missing for SoC of the at91sam9x5 familly that embed USART3.
Reported-by: Jiri Prchal <jiri.prchal@aksignal.cz>
[b.brezillon@overkiz.com: advised to place changes in at91sam9x5_usart3.dtsi]
Acked-by: Boris BREZILLON <b.brezillon@overkiz.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
With some devices, transfer hangs during I2C frame transmission. This issue
disappears when reducing the internal frequency of the TWI IP. Even if it is
indicated that internal clock max frequency is 66MHz, it seems we have
oversampling on I2C signals making TWI believe that a transfer in progress
is done.
This fix has no impact on the I2C bus frequency.
Cc: <stable@vger.kernel.org> #3.10+
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Laxman Dewangan
Thierry Reding
Stephen Warren
Joseph Lo
Linus Torvalds
Fenghua Yu
H. Peter Anvin
Helge Deller
Dinh Nguyen
Olof Johansson
Florian Vaussard
Rajendra Nayak
Jarkko Nikula
Balaji T K
Brent Taylor
Nicolas Ferre
Ludovic Desroches