Pull timer fix from Thomas Gleixner:
"Correct an ordering issue in the tick broadcast code. I really wish
we'd get compensation for pain and suffering for each line of code we
write to work around dysfunctional timer hardware."
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
tick: Fix tick_broadcast_pending_mask not cleared
If the clock was set (stepped), set the action parameter to functions
in the pvclock gtod notifier chain to non-zero. This allows the
callee to only do work if the clock was stepped.
This will be used on Xen as the synchronization of the Xen wallclock
to the control domain's (dom0) system time will be done with this
notifier and updating on every timer tick is unnecessary and too
expensive.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: <xen-devel@lists.xen.org>
Link: http://lkml.kernel.org/r/1372329348-20841-4-git-send-email-david.vrabel@citrix.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Instead of passing multiple bools to timekeeping_updated(), define
flags and use a single 'action' parameter. It is then more obvious
what each timekeeping_update() call does.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: <xen-devel@lists.xen.org>
Link: http://lkml.kernel.org/r/1372329348-20841-3-git-send-email-david.vrabel@citrix.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
hrtimers_resume() only reprograms the timers for the current CPU as it
assumes that all other CPUs are offline at this point in the resume
process. If other CPUs are online then their timers will not be
corrected and they may fire at the wrong time.
When running as a Xen guest, this assumption is not true. Non-boot
CPUs are only stopped with IRQs disabled instead of offlining them.
This is a performance optimization as disabling the CPUs would add an
unacceptable amount of additional downtime during a live migration (>
200 ms for a 4 VCPU guest).
hrtimers_resume() cannot call on_each_cpu(retrigger_next_event,...)
as the other CPUs will be stopped with IRQs disabled. Instead, defer
the call to the next softirq.
[ tglx: Separated the xen change out ]
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: <xen-devel@lists.xen.org>
Link: http://lkml.kernel.org/r/1372329348-20841-2-git-send-email-david.vrabel@citrix.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Direct compare of jiffies related values does not work in the wrap
around case. Replace it with time_is_after_jiffies().
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Cc: Arjan van de Ven <arjan@infradead.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Link: http://lkml.kernel.org/r/519BC066.5080600@acm.org
Cc: stable@vger.kernel.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* freezer:
af_unix: use freezable blocking calls in read
sigtimedwait: use freezable blocking call
nanosleep: use freezable blocking call
futex: use freezable blocking call
select: use freezable blocking call
epoll: use freezable blocking call
binder: use freezable blocking calls
freezer: add new freezable helpers using freezer_do_not_count()
freezer: convert freezable helpers to static inline where possible
freezer: convert freezable helpers to freezer_do_not_count()
freezer: skip waking up tasks with PF_FREEZER_SKIP set
freezer: shorten freezer sleep time using exponential backoff
lockdep: check that no locks held at freeze time
lockdep: remove task argument from debug_check_no_locks_held
freezer: add unsafe versions of freezable helpers for CIFS
freezer: add unsafe versions of freezable helpers for NFS
When building imx_v6_v7_defconfig with imx-drm drivers selected as
modules, we get the following build errors:
ERROR: "irq_gc_mask_clr_bit" [drivers/staging/imx-drm/ipu-v3/imx-ipu-v3.ko] undefined!
ERROR: "irq_gc_mask_set_bit" [drivers/staging/imx-drm/ipu-v3/imx-ipu-v3.ko] undefined!
ERROR: "irq_gc_ack_set_bit" [drivers/staging/imx-drm/ipu-v3/imx-ipu-v3.ko] undefined!
Export the required functions to avoid this problem.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Cc: shawn.guo@linaro.org
Cc: kernel@pengutronix.de
Link: http://lkml.kernel.org/r/1372389789-7048-1-git-send-email-festevam@gmail.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Commit 02725e7471 ('genirq: Use irq_get/put functions'),
inadvertently changed can_request_irq() to return 0 for IRQs that have
no action. This causes pcibios_lookup_irq() to select only IRQs that
already have an action with IRQF_SHARED set, or to fail if there are
none. Change can_request_irq() to return 1 for IRQs that have no
action (if the first two conditions are met).
Reported-by: Bjarni Ingi Gislason <bjarniig@rhi.hi.is>
Tested-by: Bjarni Ingi Gislason <bjarniig@rhi.hi.is> (against 3.2)
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Cc: 709647@bugs.debian.org
Cc: stable@vger.kernel.org # 2.6.39+
Link: http://bugs.debian.org/709647
Link: http://lkml.kernel.org/r/1372383630.23847.40.camel@deadeye.wl.decadent.org.uk
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch alters format string's width, to align all statistics
at par with the longest struct sched_statistic member name under
/proc/<PID>/sched.
Signed-off-by: Kamalesh Babulal <kamalesh@linux.vnet.ibm.com>
Cc: peterz@infradead.org
Link: http://lkml.kernel.org/r/20130627165005.GA15583@linux.vnet.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
1672d04070 ("cgroup: fix cgroupfs_root early destruction path")
introduced CGRP_ROOT_SUBSYS_BOUND which is used to mark completion of
subsys binding on a new root; however, this broke remounts.
cgroup_remount() doesn't allow changing root options via remount and
CGRP_ROOT_SUBSYS_BOUND, which is set on all fully initialized roots,
makes the function reject all remounts.
Fix it by putting the options part in the lower 16 bits of root->flags
and masking the comparions. While at it, make cgroup_remount() emit
an error message explaining why it's rejecting a remount request, so
that it's less of a mystery.
Signed-off-by: Tejun Heo <tj@kernel.org>
pm_trace uses the system's Real Time Clock (RTC) to save the magic
number. The reason for this is that the RTC is the only reliably
available piece of hardware during resume operations where a value
can be set that will survive a reboot.
Consequence is that after a resume (even if it is successful) your
system clock will have a value corresponding to the magic number
instead of the correct date/time! It is therefore advisable to use
a program like ntp-date or rdate to reset the correct date/time from
an external time source when using this trace option.
There is no run-time message to warn users of the consequences of
enabling pm_trace. Adding a warning message to pm_trace_store()
will serve as a reminder to users to set the system date and time
after resume.
Signed-off-by: Shuah Khan <shuah.kh@samsung.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
At present we print per-entity load-tracking statistics for
cfs_rq of cgroups/runqueues. Given that per task statistics
is maintained, it can be used to know the contribution made
by the task to its parenting cfs_rq level.
This patch adds per-task load-tracking statistics to /proc/<PID>/sched.
Signed-off-by: Kamalesh Babulal <kamalesh@linux.vnet.ibm.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20130625080336.GA20175@linux.vnet.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Since no one use it.
Signed-off-by: Alex Shi <alex.shi@intel.com>
Reviewed-by: Paul Turner <pjt@google.com>
Tested-by: Vincent Guittot <vincent.guittot@linaro.org>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1371694737-29336-13-git-send-email-alex.shi@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Similar to runnable_load_avg, blocked_load_avg variable, long type is
enough for removed_load in 64 bit or 32 bit machine.
Then we avoid the expensive atomic64 operations on 32 bit machine.
Signed-off-by: Alex Shi <alex.shi@intel.com>
Reviewed-by: Paul Turner <pjt@google.com>
Tested-by: Vincent Guittot <vincent.guittot@linaro.org>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1371694737-29336-12-git-send-email-alex.shi@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Since tg->load_avg is smaller than tg->load_weight, we don't need a
atomic64_t variable for load_avg in 32 bit machine.
The same reason for cfs_rq->tg_load_contrib.
The atomic_long_t/unsigned long variable type are more efficient and
convenience for them.
Signed-off-by: Alex Shi <alex.shi@intel.com>
Tested-by: Vincent Guittot <vincent.guittot@linaro.org>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1371694737-29336-11-git-send-email-alex.shi@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Since the 'u64 runnable_load_avg, blocked_load_avg' in cfs_rq struct are
smaller than 'unsigned long' cfs_rq->load.weight. We don't need u64
vaiables to describe them. unsigned long is more efficient and convenience.
Signed-off-by: Alex Shi <alex.shi@intel.com>
Reviewed-by: Paul Turner <pjt@google.com>
Tested-by: Vincent Guittot <vincent.guittot@linaro.org>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1371694737-29336-10-git-send-email-alex.shi@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Aside from using runnable load average in background, move_tasks is
also the key function in load balance. We need consider the runnable
load average in it in order to make it an apple to apple load
comparison.
Morten had caught a div u64 bug on ARM, thanks!
Thanks-to: Morten Rasmussen <morten.rasmussen@arm.com>
Signed-off-by: Alex Shi <alex.shi@intel.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1371694737-29336-8-git-send-email-alex.shi@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
They are the base values in load balance, update them with rq runnable
load average, then the load balance will consider runnable load avg
naturally.
We also try to include the blocked_load_avg as cpu load in balancing,
but that cause kbuild performance drop 6% on every Intel machine, and
aim7/oltp drop on some of 4 CPU sockets machines.
Or only add blocked_load_avg into get_rq_runable_load, hackbench still
drop a little on NHM EX.
Signed-off-by: Alex Shi <alex.shi@intel.com>
Reviewed-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1371694737-29336-7-git-send-email-alex.shi@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
To get the latest runnable info, we need do this cpuload update after
task_tick.
Signed-off-by: Alex Shi <alex.shi@intel.com>
Reviewed-by: Paul Turner <pjt@google.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1371694737-29336-6-git-send-email-alex.shi@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The woken migrated task will __synchronize_entity_decay(se); in
migrate_task_rq_fair, then it needs to set
`se->avg.last_runnable_update -= (-se->avg.decay_count) << 20' before
update_entity_load_avg, in order to avoid sleep time is updated twice
for se.avg.load_avg_contrib in both __syncchronize and
update_entity_load_avg.
However if the sleeping task is woken up from the same cpu, it miss
the last_runnable_update before update_entity_load_avg(se, 0, 1), then
the sleep time was used twice in both functions. So we need to remove
the double sleep time accounting.
Paul also contributed some code comments in this commit.
Signed-off-by: Alex Shi <alex.shi@intel.com>
Reviewed-by: Paul Turner <pjt@google.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1371694737-29336-5-git-send-email-alex.shi@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We need to initialize the se.avg.{decay_count, load_avg_contrib} for a
new forked task. Otherwise random values of above variables cause a
mess when a new task is enqueued:
enqueue_task_fair
enqueue_entity
enqueue_entity_load_avg
and make fork balancing imbalance due to incorrect load_avg_contrib.
Further more, Morten Rasmussen notice some tasks were not launched at
once after created. So Paul and Peter suggest giving a start value for
new task runnable avg time same as sched_slice().
PeterZ said:
> So the 'problem' is that our running avg is a 'floating' average; ie. it
> decays with time. Now we have to guess about the future of our newly
> spawned task -- something that is nigh impossible seeing these CPU
> vendors keep refusing to implement the crystal ball instruction.
>
> So there's two asymptotic cases we want to deal well with; 1) the case
> where the newly spawned program will be 'nearly' idle for its lifetime;
> and 2) the case where its cpu-bound.
>
> Since we have to guess, we'll go for worst case and assume its
> cpu-bound; now we don't want to make the avg so heavy adjusting to the
> near-idle case takes forever. We want to be able to quickly adjust and
> lower our running avg.
>
> Now we also don't want to make our avg too light, such that it gets
> decremented just for the new task not having had a chance to run yet --
> even if when it would run, it would be more cpu-bound than not.
>
> So what we do is we make the initial avg of the same duration as that we
> guess it takes to run each task on the system at least once -- aka
> sched_slice().
>
> Of course we can defeat this with wakeup/fork bombs, but in the 'normal'
> case it should be good enough.
Paul also contributed most of the code comments in this commit.
Signed-off-by: Alex Shi <alex.shi@intel.com>
Reviewed-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
Reviewed-by: Paul Turner <pjt@google.com>
[peterz; added explanation of sched_slice() usage]
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1371694737-29336-4-git-send-email-alex.shi@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The following 2 variables are only used under CONFIG_SMP, so its
better to move their definiation into CONFIG_SMP too.
atomic64_t load_avg;
atomic_t runnable_avg;
Signed-off-by: Alex Shi <alex.shi@intel.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1371694737-29336-3-git-send-email-alex.shi@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Remove CONFIG_FAIR_GROUP_SCHED that covers the runnable info, then
we can use runnable load variables.
Also remove 2 CONFIG_FAIR_GROUP_SCHED setting which is not in reverted
patch(introduced in 9ee474f), but also need to revert.
Signed-off-by: Alex Shi <alex.shi@intel.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/51CA76A3.3050207@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull perf fixes from Ingo Molnar:
"Three small fixlets"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
hw_breakpoint: Use cpu_possible_mask in {reserve,release}_bp_slot()
hw_breakpoint: Fix cpu check in task_bp_pinned(cpu)
kprobes: Fix arch_prepare_kprobe to handle copy insn failures
kernel/cgroup.c still has places where a RCU pointer is set and
accessed directly without going through RCU_INIT_POINTER() or
rcu_dereference_protected(). They're all properly protected accesses
so nothing is broken but it leads to spurious sparse RCU address space
warnings.
Substitute direct accesses with RCU_INIT_POINTER() and
rcu_dereference_protected(). Note that %true is specified as the
extra condition for all derference updates. This isn't ideal as all
it does is suppressing warning without actually policing
synchronization rules; however, most are scheduled to be removed
pretty soon along with css_id itself, so no reason to be more
elaborate.
Combined with the previous changes, this removes all RCU related
sparse warnings from cgroup.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Acked-by; Li Zefan <lizefan@huawei.com>
There are several places in kernel/cgroup.c where task->cgroups is
accessed and modified without going through proper RCU accessors.
None is broken as they're all lock protected accesses; however, this
still triggers sparse RCU address space warnings.
* Consistently use task_css_set() for task->cgroups dereferencing.
* Use RCU_INIT_POINTER() to clear task->cgroups to &init_css_set on
exit.
* Remove unnecessary rcu_dereference_raw() from cset->subsys[]
dereference in cgroup_exit().
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Acked-by: Li Zefan <lizefan@huawei.com>
This isn't strictly necessary as all subsystems specified in
@subsys_mask are guaranteed to be pinned; however, it does spuriously
trigger lockdep warning. Let's grab cgroup_mutex around it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Li Zefan <lizefan@huawei.com>
cgroupfs_root used to have ->actual_subsys_mask in addition to
->subsys_mask. a8a648c4ac ("cgroup: remove
cgroup->actual_subsys_mask") removed it noting that the subsys_mask is
essentially temporary and doesn't belong in cgroupfs_root; however,
the patch made it impossible to tell whether a cgroupfs_root actually
has the subsystems bound or just have the bits set leading to the
following BUG when trying to mount with subsystems which are already
mounted elsewhere.
kernel BUG at kernel/cgroup.c:1038!
invalid opcode: 0000 [#1] PREEMPT SMP DEBUG_PAGEALLOC
...
CPU: 1 PID: 7973 Comm: mount Tainted: G W 3.10.0-rc7-next-20130625-sasha-00011-g1c1dc0e #1105
task: ffff880fc0ae8000 ti: ffff880fc0b9a000 task.ti: ffff880fc0b9a000
RIP: 0010:[<ffffffff81249b29>] [<ffffffff81249b29>] rebind_subsystems+0x409/0x5f0
...
Call Trace:
[<ffffffff8124bd4f>] cgroup_kill_sb+0xff/0x210
[<ffffffff813d21af>] deactivate_locked_super+0x4f/0x90
[<ffffffff8124f3b3>] cgroup_mount+0x673/0x6e0
[<ffffffff81257169>] cpuset_mount+0xd9/0x110
[<ffffffff813d2580>] mount_fs+0xb0/0x2d0
[<ffffffff81404afd>] vfs_kern_mount+0xbd/0x180
[<ffffffff814070b5>] do_new_mount+0x145/0x2c0
[<ffffffff814085d6>] do_mount+0x356/0x3c0
[<ffffffff8140873d>] SyS_mount+0xfd/0x140
[<ffffffff854eb600>] tracesys+0xdd/0xe2
We still want rebind_subsystems() to take added/removed masks, so
let's fix it by marking whether a cgroupfs_root has finished binding
or not. Also, document what's going on around ->subsys_mask
initialization so that similar mistakes aren't repeated.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Sasha Levin <sasha.levin@oracle.com>
Acked-by: Li Zefan <lizefan@huawei.com>
Injects EDEADLK conditions at pseudo-random interval, with
exponential backoff up to UINT_MAX (to ensure that every lock
operation still completes in a reasonable time).
This way we can test the wound slowpath even for ww mutex users
where contention is never expected, and the ww deadlock
avoidance algorithm is only needed for correctness against
malicious userspace. An example would be protecting kernel
modesetting properties, which thanks to single-threaded X isn't
really expected to contend, ever.
I've looked into using the CONFIG_FAULT_INJECTION
infrastructure, but decided against it for two reasons:
- EDEADLK handling is mandatory for ww mutex users and should
never affect the outcome of a syscall. This is in contrast to -ENOMEM
injection. So fine configurability isn't required.
- The fault injection framework only allows to set a simple
probability for failure. Now the probability that a ww mutex acquire
stage with N locks will never complete (due to too many injected
EDEADLK backoffs) is zero. But the expected number of ww_mutex_lock
operations for the completely uncontended case would be O(exp(N)).
The per-acuiqire ctx exponential backoff solution choosen here only
results in O(log N) overhead due to injection and so O(log N * N)
lock operations. This way we can fail with high probability (and so
have good test coverage even for fancy backoff and lock acquisition
paths) without running into patalogical cases.
Note that EDEADLK will only ever be injected when we managed to
acquire the lock. This prevents any behaviour changes for users
which rely on the EALREADY semantics.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: dri-devel@lists.freedesktop.org
Cc: linaro-mm-sig@lists.linaro.org
Cc: rostedt@goodmis.org
Cc: daniel@ffwll.ch
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20130620113117.4001.21681.stgit@patser
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Wound/wait mutexes are used when other multiple lock
acquisitions of a similar type can be done in an arbitrary
order. The deadlock handling used here is called wait/wound in
the RDBMS literature: The older tasks waits until it can acquire
the contended lock. The younger tasks needs to back off and drop
all the locks it is currently holding, i.e. the younger task is
wounded.
For full documentation please read Documentation/ww-mutex-design.txt.
References: https://lwn.net/Articles/548909/
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Rob Clark <robdclark@gmail.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: dri-devel@lists.freedesktop.org
Cc: linaro-mm-sig@lists.linaro.org
Cc: rostedt@goodmis.org
Cc: daniel@ffwll.ch
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/51C8038C.9000106@canonical.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This will allow me to call functions that have multiple
arguments if fastpath fails. This is required to support ticket
mutexes, because they need to be able to pass an extra argument
to the fail function.
Originally I duplicated the functions, by adding
__mutex_fastpath_lock_retval_arg. This ended up being just a
duplication of the existing function, so a way to test if
fastpath was called ended up being better.
This also cleaned up the reservation mutex patch some by being
able to call an atomic_set instead of atomic_xchg, and making it
easier to detect if the wrong unlock function was previously
used.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: dri-devel@lists.freedesktop.org
Cc: linaro-mm-sig@lists.linaro.org
Cc: robclark@gmail.com
Cc: rostedt@goodmis.org
Cc: daniel@ffwll.ch
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20130620113105.4001.83929.stgit@patser
Signed-off-by: Ingo Molnar <mingo@kernel.org>
ip_vs.h is not necessary for sysctl_binary.c.
prepare for the next patch to avoid compile issue.
Signed-off-by: JunweiZhang <junwei.zhang@6wind.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Reviewed-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
Avoid waking up every thread sleeping in a futex_wait call during
suspend and resume by calling a freezable blocking call. Previous
patches modified the freezer to avoid sending wakeups to threads
that are blocked in freezable blocking calls.
This call was selected to be converted to a freezable call because
it doesn't hold any locks or release any resources when interrupted
that might be needed by another freezing task or a kernel driver
during suspend, and is a common site where idle userspace tasks are
blocked.
Signed-off-by: Colin Cross <ccross@android.com>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: arve@android.com
Cc: Tejun Heo <tj@kernel.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Darren Hart <dvhart@linux.intel.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Link: http://lkml.kernel.org/r/1367458508-9133-8-git-send-email-ccross@android.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The futex_keys of process shared futexes are generated from the page
offset, the mapping host and the mapping index of the futex user space
address. This should result in an unique identifier for each futex.
Though this is not true when futexes are located in different subpages
of an hugepage. The reason is, that the mapping index for all those
futexes evaluates to the index of the base page of the hugetlbfs
mapping. So a futex at offset 0 of the hugepage mapping and another
one at offset PAGE_SIZE of the same hugepage mapping have identical
futex_keys. This happens because the futex code blindly uses
page->index.
Steps to reproduce the bug:
1. Map a file from hugetlbfs. Initialize pthread_mutex1 at offset 0
and pthread_mutex2 at offset PAGE_SIZE of the hugetlbfs
mapping.
The mutexes must be initialized as PTHREAD_PROCESS_SHARED because
PTHREAD_PROCESS_PRIVATE mutexes are not affected by this issue as
their keys solely depend on the user space address.
2. Lock mutex1 and mutex2
3. Create thread1 and in the thread function lock mutex1, which
results in thread1 blocking on the locked mutex1.
4. Create thread2 and in the thread function lock mutex2, which
results in thread2 blocking on the locked mutex2.
5. Unlock mutex2. Despite the fact that mutex2 got unlocked, thread2
still blocks on mutex2 because the futex_key points to mutex1.
To solve this issue we need to take the normal page index of the page
which contains the futex into account, if the futex is in an hugetlbfs
mapping. In other words, we calculate the normal page mapping index of
the subpage in the hugetlbfs mapping.
Mappings which are not based on hugetlbfs are not affected and still
use page->index.
Thanks to Mel Gorman who provided a patch for adding proper evaluation
functions to the hugetlbfs code to avoid exposing hugetlbfs specific
details to the futex code.
[ tglx: Massaged changelog ]
Signed-off-by: Zhang Yi <zhang.yi20@zte.com.cn>
Reviewed-by: Jiang Biao <jiang.biao2@zte.com.cn>
Tested-by: Ma Chenggong <ma.chenggong@zte.com.cn>
Reviewed-by: 'Mel Gorman' <mgorman@suse.de>
Acked-by: 'Darren Hart' <dvhart@linux.intel.com>
Cc: 'Peter Zijlstra' <peterz@infradead.org>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/000101ce71a6%24a83c5880%24f8b50980%24@com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Before 1a57423166 ("cgroup: make hierarchy_id use cyclic idr"),
hierarchy IDs were allocated from 0. As the dummy hierarchy was
always the one first initialized, it got assigned 0 and all other
hierarchies from 1. The patch accidentally changed the minimum
useable ID to 2.
Let's restore ID 0 for dummy_root and while at it reserve 1 for
unified hierarchy.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Li Zefan <lizefan@huawei.com>
Cc: stable@vger.kernel.org
There are quite a few places where all loaded [builtin] subsys are
iterated. Implement for_each_[builtin_]subsys() and replace manual
iterations with those to simplify those places a bit. The new
iterators automatically skip NULL subsystems. This shouldn't cause
any functional difference.
Iteration loops which scan all subsystems and then skipping modular
ones explicitly are converted to use for_each_builtin_subsys().
While at it, reorder variable declarations and adjust whitespaces a
bit in the affected functions.
v2: Add lockdep_assert_held() in for_each_subsys() and add comments
about synchronization as suggested by Li.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Li Zefan <lizefan@huawei.com>
cgroup_init() was doing init_css_set initialization outside
cgroup_mutex, which is fine but we want to add lockdep annotation on
subsystem iterations and cgroup_init() will trigger it spuriously.
Move init_css_set initialization inside cgroup_mutex.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Li Zefan <lizefan@huawei.com>
Use irq_get_trigger_type() to get the IRQ trigger type flags
instead calling irqd_get_trigger_type(irq_desc_get_irq_data(virq))
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Acked-by: Grant Likely <grant.likely@linaro.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-mips@linux-mips.org
Link: http://lkml.kernel.org/r/1371228049-27080-8-git-send-email-javier.martinez@collabora.co.uk
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
for_each_subsys() walks over subsystems attached to a hierarchy and
we're gonna add iterators which walk over all available subsystems.
Rename for_each_subsys() to for_each_root_subsys() so that it's more
appropriately named and for_each_subsys() can be used to iterate all
subsystems.
While at it, remove unnecessary underbar prefix from macro arguments,
put them inside parentheses, and adjust indentation for the two
for_each_*() macros.
This patch is purely cosmetic.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Li Zefan <lizefan@huawei.com>
find_css_set() passes uninitialized on-stack template[] array to
find_existing_css_set() which sets the entries for all subsystems.
Passing around an uninitialized array is a bit icky and we want to
introduce an iterator which only iterates loaded subsystems. Let's
initialize it on definition.
While at it, also make the following cosmetic cleanups.
* Convert to proper /** comments.
* Reorder variable declarations.
* Replace comment on synchronization with lockdep_assert_held().
This patch doesn't make any functional differences.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Li Zefan <lizefan@huawei.com>
cgroup curiously has two subsystem masks, ->subsys_mask and
->actual_subsys_mask. The latter only exists because the new target
subsys_mask is passed into rebind_subsystems() via @root>subsys_mask.
rebind_subsystems() needs to know what the current mask is to decide
how to reach the target mask so ->actual_subsys_mask is used as the
temp location to remember the current state.
Adding a temporary field to a permanent data structure is rather silly
and can be misleading. Update rebind_subsystems() to take @added_mask
and @removed_mask instead and remove @root->actual_subsys_mask.
This patch shouldn't introduce any behavior changes.
v2: Comment and description updated as suggested by Li.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Li Zefan <lizefan@huawei.com>
Global variable names in kernel/cgroup.c are asking for trouble -
subsys, roots, rootnode and so on. Rename them to have "cgroup_"
prefix.
* s/subsys/cgroup_subsys/
* s/rootnode/cgroup_dummy_root/
* s/dummytop/cgroup_cummy_top/
* s/roots/cgroup_roots/
* s/root_count/cgroup_root_count/
This patch is purely cosmetic.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Li Zefan <lizefan@huawei.com>
On an SMP system with only one global clockevent and a dummy
clockevent per CPU we run into problems. We want the dummy
clockevents to be registered as the per CPU tick devices, but
we can only achieve that if we register the dummy clockevents
before the global clockevent or if we artificially inflate the
rating of the dummy clockevents to be higher than the rating
of the global clockevent. Failure to do so leads to boot
hangs when the dummy timers are registered on all other CPUs
besides the CPU that accepted the global clockevent as its tick
device and there is no broadcast timer to poke the dummy
devices.
If we're registering multiple clockevents and one clockevent is
global and the other is local to a particular CPU we should
choose to use the local clockevent regardless of the rating of
the device. This way, if the clockevent is a dummy it will take
the tick device duty as long as there isn't a higher rated tick
device and any global clockevent will be bumped out into
broadcast mode, fixing the problem described above.
Reported-and-tested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Tested-by: soren.brinkmann@xilinx.com
Cc: John Stultz <john.stultz@linaro.org>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: John Stultz <john.stultz@linaro.org>
Link: http://lkml.kernel.org/r/20130613183950.GA32061@codeaurora.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Commit 088f40b7b0 ("genirq: Generic chip:
Add linear irq domain support") missed kerneldoc for the gcflags
argument of irq_alloc_domain_generic_chips(). Add it now.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Link: http://lkml.kernel.org/r/1371564513-4327-1-git-send-email-james.hogan@imgtec.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
ERROR: space required before the open parenthesis '('
WARNING: Prefer pr_warn(... to pr_warning(...
Just fix above 2 issue.
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Add the hardware interrupt number to the output of /proc/interrupts.
It is often important to have access to the hardware interrupt number because
it identifies exactly how an interrupt signal is wired up to the interrupt
controller. This is especially important when using irq_domains since irq
numbers get dynamically allocated in that case, and have no relation to the
actual hardware number.
Note: This output is currently conditional on whether or not the irq_domain
pointer is set; however hwirq could still be used without irq_domain. It
may be worthwhile to always output the hwirq number regardless of the
domain pointer.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Tested-by: Olof Johansson <olof@lixom.net>
Cc: Ben Herrenschmidt <benh@kernel.crashing.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Over the years, irq_linear_revmap() gained tests and checks to make sure
callers were using it safely, which while important, also make it less
of a fast path. After the irqdomain refactoring done recently, it is now
possible to make irq_linear_revmap() a fast path again. This patch moves
irq_linear_revmap() to the header file and makes it a static inline so
that interrupt controller drivers using a linear mapping can decode the
virq from a hwirq in just a couple of instructions.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Originally, irq_domain_associate_many() was designed to unwind the
mapped irqs on a failure of any individual association. However, that
proved to be a problem with certain IRQ controllers. Some of them only
support a subset of irqs, and will fail when attempting to map a
reserved IRQ. In those cases we want to map as many IRQs as possible, so
instead it is better for irq_domain_associate_many() to make a
best-effort attempt to map irqs, but not fail if any or all of them
don't succeed. If a caller really cares about how many irqs got
associated, then it should instead go back and check that all of the
irqs is cares about were mapped.
The original design open-coded the individual association code into the
body of irq_domain_associate_many(), but with no longer needing to
unwind associations, the code becomes simpler to split out
irq_domain_associate() to contain the bulk of the logic, and
irq_domain_associate_many() to be a simple loop wrapper.
This patch also adds a new error check to the associate path to make
sure it isn't called for an irq larger than the controller can handle,
and adds locking so that the irq_domain_mutex is held while setting up a
new association.
v3: Fixup missing change to irq_domain_add_tree()
v2: Fixup x86 warning. irq_domain_associate_many() no longer returns an
error code, but reports errors to the printk log directly. In the
majority of cases we don't actually want to fail if there is a
problem, but rather log it and still try to boot the system.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
irqdomain: Fix flubbed irq_domain_associate_many refactoring
commit d39046ec72, "irqdomain: Refactor irq_domain_associate_many()" was
missing the following hunk which causes a boot failure on anything using
irq_domain_add_tree() to allocate an irq domain.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Cc: Michael Neuling <mikey@neuling.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>,
Cc: Thomas Gleixner <tglx@linutronix.de>,
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Adds tracepoints to pm_qos_add_request, pm_qos_update_request,
pm_qos_remove_request, and pm_qos_update_request_timeout.
It's useful for checking pm_qos_class, value, and timeout_us.
Signed-off-by: Sahara <keun-o.park@windriver.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch adds tracepoints to pm_qos_update_target and
pm_qos_update_flags. It's useful for checking pm qos action,
previous value and current value.
Signed-off-by: Sahara <keun-o.park@windriver.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch keeps track of how long perf's NMI handler is taking,
and also calculates how many samples perf can take a second. If
the sample length times the expected max number of samples
exceeds a configurable threshold, it drops the sample rate.
This way, we don't have a runaway sampling process eating up the
CPU.
This patch can tend to drop the sample rate down to level where
perf doesn't work very well. *BUT* the alternative is that my
system hangs because it spends all of its time handling NMIs.
I'll take a busted performance tool over an entire system that's
busted and undebuggable any day.
BTW, my suspicion is that there's still an underlying bug here.
Using the HPET instead of the TSC is definitely a contributing
factor, but I suspect there are some other things going on.
But, I can't go dig down on a bug like that with my machine
hanging all the time.
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: paulus@samba.org
Cc: acme@ghostprotocols.net
Cc: Dave Hansen <dave@sr71.net>
[ Prettified it a bit. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull x86 fixes from Peter Anvin:
"This series fixes a couple of build failures, and fixes MTRR cleanup
and memory setup on very specific memory maps.
Finally, it fixes triggering backtraces on all CPUs, which was
inadvertently disabled on x86."
* 'x86/urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/efi: Fix dummy variable buffer allocation
x86: Fix trigger_all_cpu_backtrace() implementation
x86: Fix section mismatch on load_ucode_ap
x86: fix build error and kconfig for ia32_emulation and binfmt
range: Do not add new blank slot with add_range_with_merge
x86, mtrr: Fix original mtrr range get for mtrr_cleanup
The recent modification in the cpuidle framework consolidated the
timer broadcast code across the different drivers by setting a new
flag in the idle state. It tells the cpuidle core code to enter/exit
the broadcast mode for the cpu when entering a deep idle state. The
broadcast timer enter/exit is no longer handled by the back-end
driver.
This change made the local interrupt to be enabled *before* calling
CLOCK_EVENT_NOTIFY_EXIT.
On a tegra114, a four cores system, when the flag has been introduced
in the driver, the following warning appeared:
WARNING: at kernel/time/tick-broadcast.c:578 tick_broadcast_oneshot_control
CPU: 2 PID: 0 Comm: swapper/2 Not tainted 3.10.0-rc3-next-20130529+ #15
[<c00667f8>] (tick_broadcast_oneshot_control+0x1a4/0x1d0) from [<c0065cd0>] (tick_notify+0x240/0x40c)
[<c0065cd0>] (tick_notify+0x240/0x40c) from [<c0044724>] (notifier_call_chain+0x44/0x84)
[<c0044724>] (notifier_call_chain+0x44/0x84) from [<c0044828>] (raw_notifier_call_chain+0x18/0x20)
[<c0044828>] (raw_notifier_call_chain+0x18/0x20) from [<c00650cc>] (clockevents_notify+0x28/0x170)
[<c00650cc>] (clockevents_notify+0x28/0x170) from [<c033f1f0>] (cpuidle_idle_call+0x11c/0x168)
[<c033f1f0>] (cpuidle_idle_call+0x11c/0x168) from [<c000ea94>] (arch_cpu_idle+0x8/0x38)
[<c000ea94>] (arch_cpu_idle+0x8/0x38) from [<c005ea80>] (cpu_startup_entry+0x60/0x134)
[<c005ea80>] (cpu_startup_entry+0x60/0x134) from [<804fe9a4>] (0x804fe9a4)
I don't have the hardware, so I wasn't able to reproduce the warning
but after looking a while at the code, I deduced the following:
1. the CPU2 enters a deep idle state and sets the broadcast timer
2. the timer expires, the tick_handle_oneshot_broadcast function is
called, setting the tick_broadcast_pending_mask and waking up the
idle cpu CPU2
3. the CPU2 exits idle handles the interrupt and then invokes
tick_broadcast_oneshot_control with CLOCK_EVENT_NOTIFY_EXIT which
runs the following code:
[...]
if (dev->next_event.tv64 == KTIME_MAX)
goto out;
if (cpumask_test_and_clear_cpu(cpu,
tick_broadcast_pending_mask))
goto out;
[...]
So if there is no next event scheduled for CPU2, we fulfil the
first condition and jump out without clearing the
tick_broadcast_pending_mask.
4. CPU2 goes to deep idle again and calls
tick_broadcast_oneshot_control with CLOCK_NOTIFY_EVENT_ENTER but
with the tick_broadcast_pending_mask set for CPU2, triggering the
warning.
The issue only surfaced due to the modifications of the cpuidle
framework, which resulted in interrupts being enabled before the call
to the clockevents code. If the call happens before interrupts have
been enabled, the warning cannot trigger, because there is still the
event pending which caused the broadcast timer expiry.
Move the check for the next event below the check for the pending bit,
so the pending bit gets cleared whether an event is scheduled on the
cpu or not.
[ tglx: Massaged changelog ]
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reported-and-tested-by: Joseph Lo <josephl@nvidia.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linaro-kernel@lists.linaro.org
Link: http://lkml.kernel.org/r/1371485735-31249-1-git-send-email-daniel.lezcano@linaro.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Commit a938da06 introduced a useful little log message to tell
users/debuggers which wakeup source aborted a suspend. However,
this message is only printed if the abort happens during the
in-kernel suspend path (after writing /sys/power/state).
The full specification of the /sys/power/wakeup_count facility
allows user-space power managers to double-check if wakeups have
already happened before it actually tries to suspend (e.g. while it
was running user-space pre-suspend hooks), by writing the last known
wakeup_count value to /sys/power/wakeup_count. This patch changes
the sysfs handler for that node to also print said log message if
that write fails, so that we can figure out the offending wakeup
source for both kinds of suspend aborts.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The valid start index for pm_qos_array is not 0, but
PM_QOS_CPU_DMA_LATENCY. There is a null_pm_qos at index 0 of
pm_qos_array. However, null_pm_qos is not created as misc device so
that inclusion of 0 index for checking pm_qos_class especially for
file operations is not proper here.
[rjw: Changelog, a bit]
Signed-off-by: Sahara <keun-o.park@windriver.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull scheduler fixes from Ingo Molnar:
"Two smaller fixes - plus a context tracking tracing fix that is a bit
bigger"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
tracing/context-tracking: Add preempt_schedule_context() for tracing
sched: Fix clear NOHZ_BALANCE_KICK
sched/x86: Construct all sibling maps if smt
Pull perf fixes from Ingo Molnar:
"Four fixes. The mmap ones are unfortunately larger than desired -
fuzzing uncovered bugs that needed perf context life time management
changes to fix properly"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86: Fix broken PEBS-LL support on SNB-EP/IVB-EP
perf: Fix mmap() accounting hole
perf: Fix perf mmap bugs
kprobes: Fix to free gone and unused optprobes
Pull cpu idle fixes from Thomas Gleixner:
- Add a missing irq enable. Fallout of the idle conversion
- Fix stackprotector wreckage caused by the idle conversion
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
idle: Enable interrupts in the weak arch_cpu_idle() implementation
idle: Add the stack canary init to cpu_startup_entry()
Pull timer fixes from Thomas Gleixner:
- Fix inconstinant clock usage in virtual time accounting
- Fix a build error in KVM caused by the NOHZ work
- Remove a pointless timekeeping duty assignment which breaks NOHZ
- Use a proper notifier return value to avoid random behaviour
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
tick: Remove useless timekeeping duty attribution to broadcast source
nohz: Fix notifier return val that enforce timekeeping
kvm: Move guest entry/exit APIs to context_tracking
vtime: Use consistent clocks among nohz accounting
This patch simply moves all per-cpu variables into the new
single per-cpu "struct bp_cpuinfo".
To me this looks more logical and clean, but this can also
simplify the further potential changes. In particular, I do not
think this memory should be per-cpu, it is never used "locally".
After this change it is trivial to turn it into, say,
bootmem[nr_cpu_ids].
Reported-by: Vince Weaver <vincent.weaver@maine.edu>
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Frederic Weisbecker <fweisbec@gmail.com>
Link: http://lkml.kernel.org/r/20130620155020.GA6350@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
1. register_wide_hw_breakpoint() can use unregister_ if failure,
no need to duplicate the code.
2. "struct perf_event **pevent" adds the unnecesary lever of
indirection and complication, use per_cpu(*cpu_events, cpu).
Reported-by: Vince Weaver <vincent.weaver@maine.edu>
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Frederic Weisbecker <fweisbec@gmail.com>
Link: http://lkml.kernel.org/r/20130620155018.GA6347@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Add the trivial helper which simply returns cpumask_of() or
cpu_possible_mask depending on bp->cpu.
Change fetch_bp_busy_slots() and toggle_bp_slot() to always do
for_each_cpu(cpumask_of_bp) to simplify the code and avoid the
code duplication.
Reported-by: Vince Weaver <vincent.weaver@maine.edu>
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Frederic Weisbecker <fweisbec@gmail.com>
Link: http://lkml.kernel.org/r/20130620155015.GA6340@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Change toggle_bp_slot() to make "weight" negative if !enable.
This way we can always use "+ weight" without additional "if
(enable)" check and toggle_bp_task_slot() no longer needs this
arg.
Reported-by: Vince Weaver <vincent.weaver@maine.edu>
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Frederic Weisbecker <fweisbec@gmail.com>
Link: http://lkml.kernel.org/r/20130620155013.GA6337@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The enable/disable logic in toggle_bp_slot() is not symmetrical
and imho very confusing. "old_count" in toggle_bp_task_slot() is
actually new_count because this bp was already removed from the
list.
Change toggle_bp_slot() to always call list_add/list_del after
toggle_bp_task_slot(). This way old_idx is task_bp_pinned() and
this entry should be decremented, new_idx is +/-weight and we
need to increment this element. The code/logic looks obvious.
Reported-by: Vince Weaver <vincent.weaver@maine.edu>
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Frederic Weisbecker <fweisbec@gmail.com>
Link: http://lkml.kernel.org/r/20130620155011.GA6330@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
trinity fuzzer triggered WARN_ONCE("Can't find any breakpoint
slot") in arch_install_hw_breakpoint() but the problem is not
arch-specific.
The problem is, task_bp_pinned(cpu) checks "cpu == iter->cpu"
but this doesn't account the "all cpus" events with iter->cpu <
0.
This means that, say, register_user_hw_breakpoint(tsk) can
happily create the arbitrary number > HBP_NUM of breakpoints
which can not be activated. toggle_bp_task_slot() is equally
wrong by the same reason and nr_task_bp_pinned[] can have
negative entries.
Simple test:
# perl -e 'sleep 1 while 1' &
# perf record -e mem:0x10,mem:0x10,mem:0x10,mem:0x10,mem:0x10 -p `pidof perl`
Before this patch this triggers the same problem/WARN_ON(),
after the patch it correctly fails with -ENOSPC.
Reported-by: Vince Weaver <vincent.weaver@maine.edu>
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: <stable@vger.kernel.org>
Link: http://lkml.kernel.org/r/20130620155006.GA6324@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Building full dynticks now implies that all CPUs are forced
into RCU nocb mode through CONFIG_RCU_NOCB_CPU_ALL.
The dynamic check has become useless.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Li Zhong <zhong@linux.vnet.ibm.com>
Cc: Borislav Petkov <bp@alien8.de>
When the watchdog runs, it prevents the full dynticks
CPUs from stopping their tick because the hard lockup
detector uses perf events internally, which in turn
rely on the periodic tick.
Since this is a rather confusing behaviour that is not
easy to track down and identify for those who want to
test CONFIG_NO_HZ_FULL, let's default disable the
watchdog on boot time when full dynticks is enabled.
The user can still enable it later on runtime using
proc or sysctl.
Reported-by: Steven Rostedt <rostedt@goodmis.org>
Suggested-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Li Zhong <zhong@linux.vnet.ibm.com>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Cc: Anish Singh <anish198519851985@gmail.com>
We have two very conflicting state variable names in the
watchdog:
* watchdog_enabled: This one reflects the user interface. It's
set to 1 by default and can be overriden with boot options
or sysctl/procfs interface.
* watchdog_disabled: This is the internal toggle state that
tells if watchdog threads, timers and NMI events are currently
running or not. This state mostly depends on the user settings.
It's a convenient state latch.
Now we really need to find clearer names because those
are just too confusing to encourage deep review.
watchdog_enabled now becomes watchdog_user_enabled to reflect
its purpose as an interface.
watchdog_disabled becomes watchdog_running to suggest its
role as a pure internal state.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Cc: Anish Singh <anish198519851985@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Li Zhong <zhong@linux.vnet.ibm.com>
Cc: Don Zickus <dzickus@redhat.com>
Since tp->flags assignment was moved into function enable_trace_probe(),
there is no need to use trace_probe_is_enabled to check flags
in the same function.
Remove the unnecessary checking.
Link: http://lkml.kernel.org/r/51BA7B9E.3040807@huawei.com
Acked-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Signed-off-by: zhangwei(Jovi) <jovi.zhangwei@huawei.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Add a traceoff_on_warning option in both the kernel command line as well
as a sysctl option. When set, any WARN*() function that is hit will cause
the tracing_on variable to be cleared, which disables writing to the
ring buffer.
This is useful especially when tracing a bug with function tracing. When
a warning is hit, the print caused by the warning can flood the trace with
the functions that producing the output for the warning. This can make the
resulting trace useless by either hiding where the bug happened, or worse,
by overflowing the buffer and losing the trace of the bug totally.
Acked-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
There are some cases when filtering on a set flag of a field of a tracepoint
is useful. But currently the only filtering commands for numbered fields
is ==, !=, <, <=, >, >=. This does not help when you just want to trace if
a specific flag is set. For example:
> # sudo trace-cmd record -e brcmfmac:brcmf_dbg -f 'level & 0x40000'
> disable all
> enable brcmfmac:brcmf_dbg
> path = /sys/kernel/debug/tracing/events/brcmfmac/brcmf_dbg/enable
> (level & 0x40000)
> ^
> parse_error: Invalid operator
>
When trying to trace brcmf_dbg when level has its 1 << 18 bit set, the
filter fails to perform.
By allowing a binary '&' operation, this gives the user the ability to
test a bit.
Note, a binary '|' is not added, as it doesn't make sense as fields must
be compared to constants (for now), and ORing a constant will always return
true.
Link: http://lkml.kernel.org/r/1371057385.9844.261.camel@gandalf.local.home
Suggested-by: Arend van Spriel <arend@broadcom.com>
Tested-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
The user activation/deactivation of the watchdog through boot parameters
or systcl is currently implemented with a dance involving kthreads parking
and unparking methods: the threads are unconditionally registered on
boot and they park as soon as the user want the watchdog to be disabled.
This method involves a few noisy details to handle though: the watchdog
kthreads may be unparked anytime due to hotplug operations, after which
the watchdog internals have to decide to park again if it is user-disabled.
As a result the setup() and unpark() methods need to be able to request a
reparking. This is not currently supported in the kthread infrastructure
so this piece of the watchdog code only works halfway.
Besides, unparking/reparking the watchdog kthreads consume unnecessary
cputime on hotplug operations when those could be simply ignored in the
first place.
As suggested by Srivatsa, let's instead only register the watchdog
threads when they are needed. This way we don't need to think about
hotplug operations and we don't burden the CPU onlining when the watchdog
is simply disabled.
Suggested-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Cc: Anish Singh <anish198519851985@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Li Zhong <zhong@linux.vnet.ibm.com>
Cc: Don Zickus <dzickus@redhat.com>
If the user configures NO_HZ_FULL and defines nohz_full=XXX on the
kernel command line, or enables NO_HZ_FULL_ALL, but nohz fails
due to the machine having a unstable clock, warn about it.
We do not want users thinking that they are getting the benefit
of nohz when their machine can not support it.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Li Zhong <zhong@linux.vnet.ibm.com>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Pull RCU changes from Paul E. McKenney:
"The major changes for this series are:
1. Simplify RCU's grace-period and callback processing based on
the new numbering for callbacks. These were posted to LKML at
https://lkml.org/lkml/2013/5/20/330.
2. Documentation updates. These were posted to LKML at
https://lkml.org/lkml/2013/5/20/348.
3. Miscellaneous fixes, including converting a few remaining printk()
calls to pr_*(). These were posted to LKML at
https://lkml.org/lkml/2013/5/20/324.
4. SRCU-related changes and fixes. These were posted to LKML at
https://lkml.org/lkml/2013/5/20/425.
5. Removal of TINY_PREEMPT_RCU in favor of TREE_PREEMPT_RCU for
single-CPU low-latency systems. These were posted to LKML at
https://lkml.org/lkml/2013/5/20/427."
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Just use struct ctl_table.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1371063336.2069.22.camel@joe-AO722
Signed-off-by: Ingo Molnar <mingo@kernel.org>
sd can't be NULL in init_sched_groups_power() and so checking it for NULL isn't
useful. In case it is required, then also we need to rearrange the code a bit as
we already accessed invalid pointer sd to get sg: sg = sd->groups.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/2bbe633cd74b431c05253a8ce61fdfd5066a531b.1370948150.git.viresh.kumar@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
In build_sched_groups() we don't need to call get_group() for cpus
which are already covered in previous iterations. Calling get_group()
would mark the group used and eventually leak it since we wouldn't
connect it and not find it again to free it.
This will happen only in cases where sg->cpumask contained more than
one cpu (For any topology level). This patch would free sg's memory
for all cpus leaving the group leader as the group isn't marked used
now.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/7a61e955abdcbb1dfa9fe493f11a5ec53a11ddd3.1370948150.git.viresh.kumar@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
In the beginning of build_sched_groups() we called sched_domain_span() and
cached its return value in span. Few statements later we are calling it again to
get the same pointer.
Lets use the cached value instead as it hasn't changed in between.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/834ecd507071ad88aff039352dbc7e063dd996a7.1370948150.git.viresh.kumar@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
For loop for traversing sched_domain_topology was used at multiple placed in
core.c. This patch removes code redundancy by creating for_each_sd_topology().
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/e0e04542f54e9464bd9da54f5ccfe62ec6c4c0bc.1370861520.git.viresh.kumar@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Memory for sd is allocated with kzalloc_node() which will initialize its fields
with zero. In build_sched_domain() we are setting sd->child to child even if
child is NULL, which isn't required.
Lets do it only if child isn't NULL.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/f4753a1730051341003ad2ad29a3229c7356678e.1370861520.git.viresh.kumar@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We are saving first scheduling domain for a cpu in build_sched_domains() by
iterating over the nested sd->child list. We don't actually need to do it this
way.
tl will be equal to sched_domain_topology for the first iteration and so we can
set *per_cpu_ptr(d.sd, i) based on that. So, save pointer to first SD while
running the iteration loop over tl's.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/fc473527cbc4dfa0b8eeef2a59db74684eb59a83.1370436120.git.viresh.kumar@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Most of the stuff from kernel/sched.c was moved to kernel/sched/core.c long time
back and the comments/Documentation never got updated.
I figured it out when I was going through sched-domains.txt and so thought of
fixing it globally.
I haven't crossed check if the stuff that is referenced in sched/core.c by all
these files is still present and hasn't changed as that wasn't the motive behind
this patch.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/cdff76a265326ab8d71922a1db5be599f20aad45.1370329560.git.viresh.kumar@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
default_cfs_period(), do_sched_cfs_period_timer(), do_sched_cfs_slack_timer()
already defined previously, no need to declare again.
Signed-off-by: Michael Wang <wangyun@linux.vnet.ibm.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/51AD8808.7020608@linux.vnet.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Directly use rq to save some code.
Signed-off-by: Michael Wang <wangyun@linux.vnet.ibm.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/51AD87EB.1070605@linux.vnet.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
[ Peter, this is based off of some of my work, I ran it though a few
tests and it passed. I also reviewed it, and added my SOB as I am
somewhat a co-author to it. ]
Based on the patch by Steven Rostedt from previous year:
https://lkml.org/lkml/2012/4/18/517
1)Simplify pull_rt_task() logic: search in pushable tasks of dest runqueue.
The only pullable tasks are the tasks which are pushable in their local rq,
and no others.
2)Remove .leaf_rt_rq_list member of struct rt_rq and functions connected
with it: nobody uses it since now.
Signed-off-by: Kirill Tkhai <tkhai@yandex.ru>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/287571370557898@web7d.yandex.ru
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Dave Jones hit the following bug report:
===============================
[ INFO: suspicious RCU usage. ]
3.10.0-rc2+ #1 Not tainted
-------------------------------
include/linux/rcupdate.h:771 rcu_read_lock() used illegally while idle!
other info that might help us debug this:
RCU used illegally from idle CPU! rcu_scheduler_active = 1, debug_locks = 0
RCU used illegally from extended quiescent state!
2 locks held by cc1/63645:
#0: (&rq->lock){-.-.-.}, at: [<ffffffff816b39fd>] __schedule+0xed/0x9b0
#1: (rcu_read_lock){.+.+..}, at: [<ffffffff8109d645>] cpuacct_charge+0x5/0x1f0
CPU: 1 PID: 63645 Comm: cc1 Not tainted 3.10.0-rc2+ #1 [loadavg: 40.57 27.55 13.39 25/277 64369]
Hardware name: Gigabyte Technology Co., Ltd. GA-MA78GM-S2H/GA-MA78GM-S2H, BIOS F12a 04/23/2010
0000000000000000 ffff88010f78fcf8 ffffffff816ae383 ffff88010f78fd28
ffffffff810b698d ffff88011c092548 000000000023d073 ffff88011c092500
0000000000000001 ffff88010f78fd60 ffffffff8109d7c5 ffffffff8109d645
Call Trace:
[<ffffffff816ae383>] dump_stack+0x19/0x1b
[<ffffffff810b698d>] lockdep_rcu_suspicious+0xfd/0x130
[<ffffffff8109d7c5>] cpuacct_charge+0x185/0x1f0
[<ffffffff8109d645>] ? cpuacct_charge+0x5/0x1f0
[<ffffffff8108dffc>] update_curr+0xec/0x240
[<ffffffff8108f528>] put_prev_task_fair+0x228/0x480
[<ffffffff816b3a71>] __schedule+0x161/0x9b0
[<ffffffff816b4721>] preempt_schedule+0x51/0x80
[<ffffffff816b4800>] ? __cond_resched_softirq+0x60/0x60
[<ffffffff816b6824>] ? retint_careful+0x12/0x2e
[<ffffffff810ff3cc>] ftrace_ops_control_func+0x1dc/0x210
[<ffffffff816be280>] ftrace_call+0x5/0x2f
[<ffffffff816b681d>] ? retint_careful+0xb/0x2e
[<ffffffff816b4805>] ? schedule_user+0x5/0x70
[<ffffffff816b4805>] ? schedule_user+0x5/0x70
[<ffffffff816b6824>] ? retint_careful+0x12/0x2e
------------[ cut here ]------------
What happened was that the function tracer traced the schedule_user() code
that tells RCU that the system is coming back from userspace, and to
add the CPU back to the RCU monitoring.
Because the function tracer does a preempt_disable/enable_notrace() calls
the preempt_enable_notrace() checks the NEED_RESCHED flag. If it is set,
then preempt_schedule() is called. But this is called before the user_exit()
function can inform the kernel that the CPU is no longer in user mode and
needs to be accounted for by RCU.
The fix is to create a new preempt_schedule_context() that checks if
the kernel is still in user mode and if so to switch it to kernel mode
before calling schedule. It also switches back to user mode coming back
from schedule in need be.
The only user of this currently is the preempt_enable_notrace(), which is
only used by the tracing subsystem.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1369423420.6828.226.camel@gandalf.local.home
Signed-off-by: Ingo Molnar <mingo@kernel.org>
I have faced a sequence where the Idle Load Balance was sometime not
triggered for a while on my platform, in the following scenario:
CPU 0 and CPU 1 are running tasks and CPU 2 is idle
CPU 1 kicks the Idle Load Balance
CPU 1 selects CPU 2 as the new Idle Load Balancer
CPU 2 sets NOHZ_BALANCE_KICK for CPU 2
CPU 2 sends a reschedule IPI to CPU 2
While CPU 3 wakes up, CPU 0 or CPU 1 migrates a waking up task A on CPU 2
CPU 2 finally wakes up, runs task A and discards the Idle Load Balance
task A quickly goes back to sleep (before a tick occurs on CPU 2)
CPU 2 goes back to idle with NOHZ_BALANCE_KICK set
Whenever CPU 2 will be selected as the ILB, no reschedule IPI will be sent
because NOHZ_BALANCE_KICK is already set and no Idle Load Balance will be
performed.
We must wait for the sched softirq to be raised on CPU 2 thanks to another
part the kernel to come back to clear NOHZ_BALANCE_KICK.
The proposed solution clears NOHZ_BALANCE_KICK in schedule_ipi if
we can't raise the sched_softirq for the Idle Load Balance.
Change since V1:
- move the clear of NOHZ_BALANCE_KICK in got_nohz_idle_kick if the ILB
can't run on this CPU (as suggested by Peter)
Signed-off-by: Vincent Guittot <vincent.guittot@linaro.org>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1370419991-13870-1-git-send-email-vincent.guittot@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This allows us to use pdev->name for registering a PMU device.
IMO the name is not supposed to be changed anyway.
Signed-off-by: Mischa Jonker <mjonker@synopsys.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1370339148-5566-1-git-send-email-mjonker@synopsys.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Commit 2b923c8 perf/x86: Check branch sampling priv level in generic code
was missing the check for the hypervisor (HV) priv level, so add it back.
With this patch, we get the following correct behavior:
# echo 2 >/proc/sys/kernel/perf_event_paranoid
$ perf record -j any,k noploop 1
Error:
You may not have permission to collect stats.
Consider tweaking /proc/sys/kernel/perf_event_paranoid:
-1 - Not paranoid at all
0 - Disallow raw tracepoint access for unpriv
1 - Disallow cpu events for unpriv
2 - Disallow kernel profiling for unpriv
$ perf record -j any,hv noploop 1
Error:
You may not have permission to collect stats.
Consider tweaking /proc/sys/kernel/perf_event_paranoid:
-1 - Not paranoid at all
0 - Disallow raw tracepoint access for unpriv
1 - Disallow cpu events for unpriv
2 - Disallow kernel profiling for unpriv
Signed-off-by: Stephane Eranian <eranian@google.com>
Acked-by: Petr Matousek <pmatouse@redhat.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20130606090204.GA3725@quad
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Vince's fuzzer once again found holes. This time it spotted a leak in
the locked page accounting.
When an event had redirected output and its close() was the last
reference to the buffer we didn't have a vm context to undo accounting.
Change the code to destroy the buffer on the last munmap() and detach
all redirected events at that time. This provides us the right context
to undo the vm accounting.
Reported-and-tested-by: Vince Weaver <vincent.weaver@maine.edu>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20130604084421.GI8923@twins.programming.kicks-ass.net
Cc: <stable@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cont is short for container. control group was named process container
at first, but then people found container already has a meaning in
linux kernel.
Clean up the leftover variable name @cont.
Signed-off-by: Li Zefan <lizefan@huawei.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
cgroup_serial_nr_cursor was created atomic64_t because I thought it
was never gonna used for anything other than assigning unique numbers
to cgroups and didn't want to worry about synchronization; however,
now we're using it as an event-stamp to distinguish cgroups created
before and after certain point which assumes that it's protected by
cgroup_mutex.
Let's make it clear by making it a u64. Also, rename it to
cgroup_serial_nr_next and make it point to the next nr to allocate so
that where it's pointing to is clear and more conventional.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Li Zefan <lizefan@huawei.com>
We used root->allcg_list to iterate cgroup hierarchy because at that time
cgroup_for_each_descendant_pre() hasn't been invented.
tj: In cgroup_cfts_commit(), s/@serial_nr/@update_upto/, move the
assignment right above releasing cgroup_mutex and explain what's
going on there.
Signed-off-by: Li Zefan <lizefan@huawei.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The next patch will use it to determine if a cgroup is newly created
while we're iterating the cgroup hierarchy.
tj: Rephrased the comment on top of cgroup_serial_nr_cursor.
Signed-off-by: Li Zefan <lizefan@huawei.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Joshua reported: Commit cd7b304dfa (x86, range: fix missing merge
during add range) broke mtrr cleanup on his setup in 3.9.5.
corresponding commit in upstream is fbe06b7bae.
The reason is add_range_with_merge could generate blank spot.
We could avoid that by searching new expanded start/end, that
new range should include all connected ranges in range array.
At last add the new expanded start/end to the range array.
Also move up left array so do not add new blank slot in the
range array.
-v2: move left array to avoid enhance add_range()
-v3: include fix from Joshua about memmove declaring when
DYN_DEBUG is used.
Reported-by: Joshua Covington <joshuacov@googlemail.com>
Tested-by: Joshua Covington <joshuacov@googlemail.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Link: http://lkml.kernel.org/r/1371154622-8929-3-git-send-email-yinghai@kernel.org
Cc: <stable@vger.kernel.org> v3.9
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
The memory allocated in cgroup_add_cftypes() should be freed. The
effect of this bug is we leak a bit memory everytime we unload
cfq-iosched module if blkio cgroup is enabled.
Signed-off-by: Li Zefan <lizefan@huawei.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
commit 5db9a4d99b
Author: Tejun Heo <tj@kernel.org>
Date: Sat Jul 7 16:08:18 2012 -0700
cgroup: fix cgroup hierarchy umount race
This commit fixed a race caused by the dput() in css_dput_fn(), but
the dput() in cgroup_event_remove() can also lead to the same BUG().
Signed-off-by: Li Zefan <lizefan@huawei.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
cgroup_cfts_commit() uses dget() to keep cgroup alive after cgroup_mutex
is dropped, but dget() won't prevent cgroupfs from being umounted. When
the race happens, vfs will see some dentries with non-zero refcnt while
umount is in process.
Keep running this:
mount -t cgroup -o blkio xxx /cgroup
umount /cgroup
And this:
modprobe cfq-iosched
rmmod cfs-iosched
After a while, the BUG() in shrink_dcache_for_umount_subtree() may
be triggered:
BUG: Dentry xxx{i=0,n=blkio.yyy} still in use (1) [umount of cgroup cgroup]
Signed-off-by: Li Zefan <lizefan@huawei.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
cgroup's rename(2) isn't a proper migration implementation - it can't
move the cgroup to a different parent in the hierarchy. All it can do
is swapping the name string for that cgroup. This isn't useful and
can mislead users to think that cgroup supports proper cgroup-level
migration. Disallow rename(2) if sane_behavior.
v2: Fail with -EPERM instead of -EINVAL so that it matches the vfs
return value when ->rename is not implemented as suggested by Li.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Li Zefan <lizefan@huawei.com>
There is a small race between when the cycle count is read from
the hardware and when the epoch stabilizes. Consider this
scenario:
CPU0 CPU1
---- ----
cyc = read_sched_clock()
cyc_to_sched_clock()
update_sched_clock()
...
cd.epoch_cyc = cyc;
epoch_cyc = cd.epoch_cyc;
...
epoch_ns + cyc_to_ns((cyc - epoch_cyc)
The cyc on cpu0 was read before the epoch changed. But we
calculate the nanoseconds based on the new epoch by subtracting
the new epoch from the old cycle count. Since epoch is most likely
larger than the old cycle count we calculate a large number that
will be converted to nanoseconds and added to epoch_ns, causing
time to jump forward too much.
Fix this problem by reading the hardware after the epoch has
stabilized.
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Pull VFS fixes from Al Viro:
"Several fixes + obvious cleanup (you've missed a couple of open-coded
can_lookup() back then)"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
snd_pcm_link(): fix a leak...
use can_lookup() instead of direct checks of ->i_op->lookup
move exit_task_namespaces() outside of exit_notify()
fput: task_work_add() can fail if the caller has passed exit_task_work()
ncpfs: fix rmdir returns Device or resource busy
exit_notify() does exit_task_namespaces() after
forget_original_parent(). This was needed to ensure that ->nsproxy
can't be cleared prematurely, an exiting child we are going to
reparent can do do_notify_parent() and use the parent's (ours) pid_ns.
However, after 32084504 "pidns: use task_active_pid_ns in
do_notify_parent" ->nsproxy != NULL is no longer needed, we rely
on task_active_pid_ns().
Move exit_task_namespaces() from exit_notify() to do_exit(), after
exit_fs() and before exit_task_work().
This solves the problem reported by Andrey, free_ipc_ns()->shm_destroy()
does fput() which needs task_work_add().
Note: this particular problem can be fixed if we change fput(), and
that change makes sense anyway. But there is another reason to move
the callsite. The original reason for exit_task_namespaces() from
the middle of exit_notify() was subtle and it has already gone away,
now this looks confusing. And this allows us do simplify exit_notify(),
we can avoid unlock/lock(tasklist) and we can use ->exit_state instead
of PF_EXITING in forget_original_parent().
Reported-by: Andrey Vagin <avagin@openvz.org>
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Acked-by: Andrey Vagin <avagin@openvz.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
PARISC bootup triggers the warning at kernel/cpu/idle.c:96. That's
caused by the weak arch_cpu_idle() implementation, which is provided
to avoid that architectures implement idle_poll over and over.
The switchover to polling mode happens in the first call of the weak
arch_cpu_idle() implementation, but that code fails to reenable
interrupts and therefor triggers the warning.
Fix this by enabling interrupts in the weak arch_cpu_idle() code.
[ tglx: Made the changelog match the patch ]
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Reviewed-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Link: http://lkml.kernel.org/r/1371236142.2726.43.camel@dabdike
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cont is short for container. control group was named process container
at first, but then people found container already has a meaning in
linux kernel.
Clean up the leftover variable name @cont.
Signed-off-by: Li Zefan <lizefan@huawei.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
A css (cgroup_subsys_state) is how each cgroup is represented to a
controller. As such, it can be used in hot paths across the various
subsystems different controllers are associated with.
One of the common operations is reference counting, which up until now
has been implemented using a global atomic counter and can have
significant adverse impact on scalability. For example, css refcnt
can be gotten and put multiple times by blkcg for each IO request.
For highops configurations which try to do as much per-cpu as
possible, the global frequent refcnting can be very expensive.
In general, given the various and hugely diverse paths css's end up
being used from, we need to make it cheap and highly scalable. In its
usage, css refcnting isn't very different from module refcnting.
This patch converts css refcnting to use the recently added
percpu_ref. css_get/tryget/put() directly maps to the matching
percpu_ref operations and the deactivation logic is no longer
necessary as percpu_ref already has refcnt killing.
The only complication is that as the refcnt is per-cpu,
percpu_ref_kill() in itself doesn't ensure that further tryget
operations will fail, which we need to guarantee before invoking
->css_offline()'s. This is resolved collecting kill confirmation
using percpu_ref_kill_and_confirm() and initiating the offline phase
of destruction after all css refcnt's are confirmed to be seen as
killed on all CPUs. The previous patches already splitted destruction
into two phases, so percpu_ref_kill_and_confirm() can be hooked up
easily.
This patch removes css_refcnt() which is used for rcu dereference
sanity check in css_id(). While we can add a percpu refcnt API to ask
the same question, css_id() itself is scheduled to be removed fairly
soon, so let's not bother with it. Just drop the sanity check and use
rcu_dereference_raw() instead.
v2: - init_cgroup_css() was calling percpu_ref_init() without checking
the return value. This causes two problems - the obvious lack
of error handling and percpu_ref_init() being called from
cgroup_init_subsys() before the allocators are up, which
triggers warnings but doesn't cause actual problems as the
refcnt isn't used for roots anyway. Fix both by moving
percpu_ref_init() to cgroup_create().
- The base references were put too early by
percpu_ref_kill_and_confirm() and cgroup_offline_fn() put the
refs one extra time. This wasn't noticeable because css's go
through another RCU grace period before being freed. Update
cgroup_destroy_locked() to grab an extra reference before
killing the refcnts. This problem was noticed by Kent.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Kent Overstreet <koverstreet@google.com>
Acked-by: Li Zefan <lizefan@huawei.com>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: "Alasdair G. Kergon" <agk@redhat.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Mikulas Patocka <mpatocka@redhat.com>
Cc: Glauber Costa <glommer@gmail.com>
Split cgroup_destroy_locked() into two steps and put the latter half
into cgroup_offline_fn() which is executed from a work item. The
latter half is responsible for offlining the css's, removing the
cgroup from internal lists, and propagating release notification to
the parent. The separation is to allow using percpu refcnt for css.
Note that this allows for other cgroup operations to happen between
the first and second halves of destruction, including creating a new
cgroup with the same name. As the target cgroup is marked DEAD in the
first half and cgroup internals don't care about the names of cgroups,
this should be fine. A comment explaining this will be added by the
next patch which implements the actual percpu refcnting.
As RCU freeing is guaranteed to happen after the second step of
destruction, we can use the same work item for both. This patch
renames cgroup->free_work to ->destroy_work and uses it for both
purposes. INIT_WORK() is now performed right before queueing the work
item.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Li Zefan <lizefan@huawei.com>
This patch reorders the operations in cgroup_destroy_locked() such
that the userland visible parts happen before css offlining and
removal from the ->sibling list. This will be used to make css use
percpu refcnt.
While at it, split out CGRP_DEAD related comment from the refcnt
deactivation one and correct / clarify how different guarantees are
met.
While this patch changes the specific order of operations, it
shouldn't cause any noticeable behavior difference.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Li Zefan <lizefan@huawei.com>
Pull RCU fixes from Paul McKenney:
"I must confess that this past merge window was not RCU's best showing.
This series contains three more fixes for RCU regressions:
1. A fix to __DECLARE_TRACE_RCU() that causes it to act as an
interrupt from idle rather than as a task switch from idle.
This change is needed due to the recent use of _rcuidle()
tracepoints that can be invoked from interrupt handlers as well
as from idle. Without this fix, invoking _rcuidle() tracepoints
from interrupt handlers results in splats and (more seriously)
confusion on RCU's part as to whether a given CPU is idle or not.
This confusion can in turn result in too-short grace periods and
therefore random memory corruption.
2. A fix to a subtle deadlock that could result due to RCU doing
a wakeup while holding one of its rcu_node structure's locks.
Although the probability of occurrence is low, it really
does happen. The fix, courtesy of Steven Rostedt, uses
irq_work_queue() to avoid the deadlock.
3. A fix to a silent deadlock (invisible to lockdep) due to the
interaction of timeouts posted by RCU debug code enabled by
CONFIG_PROVE_RCU_DELAY=y, grace-period initialization, and CPU
hotplug operations. This will not occur in production kernels,
but really does occur in randconfig testing. Diagnosis courtesy
of Steven Rostedt"
* 'rcu/urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/paulmck/linux-rcu:
rcu: Fix deadlock with CPU hotplug, RCU GP init, and timer migration
rcu: Don't call wakeup() with rcu_node structure ->lock held
trace: Allow idle-safe tracepoints to be called from irq
cgroup->count tracks the number of css_sets associated with the cgroup
and used only to verify that no css_set is associated when the cgroup
is being destroyed. It's superflous as the destruction path can
simply check whether cgroup->cset_links is empty instead.
Drop cgroup->count and check ->cset_links directly from
cgroup_destroy_locked().
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Li Zefan <lizefan@huawei.com>
__put_css_set() does RCU read access on @cgrp across dropping
@cgrp->count so that it can continue accessing @cgrp even if the count
reached zero and destruction of the cgroup commenced. Given that both
sides - __css_put() and cgroup_destroy_locked() - are cold paths, this
is unnecessary. Just making cgroup_destroy_locked() grab css_set_lock
while checking @cgrp->count is enough.
Remove the RCU read locking from __put_css_set() and make
cgroup_destroy_locked() read-lock css_set_lock when checking
@cgrp->count. This will also allow removing @cgrp->count.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Li Zefan <lizefan@huawei.com>
We will add another flag indicating that the cgroup is in the process
of being killed. REMOVING / REMOVED is more difficult to distinguish
and cgroup_is_removing()/cgroup_is_removed() are a bit awkward. Also,
later percpu_ref usage will involve "kill"ing the refcnt.
s/CGRP_REMOVED/CGRP_DEAD/
s/cgroup_is_removed()/cgroup_is_dead()
This patch is purely cosmetic.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Li Zefan <lizefan@huawei.com>
There's no point in using kmalloc() instead of the clearing variant
for trivial stuff. We can live dangerously elsewhere. Use kzalloc()
instead and drop 0 inits.
While at it, do trivial code reorganization in cgroup_file_open().
This patch doesn't introduce any functional changes.
v2: I was caught in the very distant past where list_del() didn't
poison and the initial version converted list_del()s to
list_del_init()s too. Li and Kent took me out of the stasis
chamber.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Kent Overstreet <koverstreet@google.com>
Acked-by: Li Zefan <lizefan@huawei.com>
cgroups and css_sets are mapped M:N and this M:N mapping is
represented by struct cg_cgroup_link which forms linked lists on both
sides. The naming around this mapping is already confusing and struct
cg_cgroup_link exacerbates the situation quite a bit.
>From cgroup side, it starts off ->css_sets and runs through
->cgrp_link_list. From css_set side, it starts off ->cg_links and
runs through ->cg_link_list. This is rather reversed as
cgrp_link_list is used to iterate css_sets and cg_link_list cgroups.
Also, this is the only place which is still using the confusing "cg"
for css_sets. This patch cleans it up a bit.
* s/cgroup->css_sets/cgroup->cset_links/
s/css_set->cg_links/css_set->cgrp_links/
s/cgroup_iter->cg_link/cgroup_iter->cset_link/
* s/cg_cgroup_link/cgrp_cset_link/
* s/cgrp_cset_link->cg/cgrp_cset_link->cset/
s/cgrp_cset_link->cgrp_link_list/cgrp_cset_link->cset_link/
s/cgrp_cset_link->cg_link_list/cgrp_cset_link->cgrp_link/
* s/init_css_set_link/init_cgrp_cset_link/
s/free_cg_links/free_cgrp_cset_links/
s/allocate_cg_links/allocate_cgrp_cset_links/
* s/cgl[12]/link[12]/ in compare_css_sets()
* s/saved_link/tmp_link/ s/tmp/tmp_links/ and a couple similar
adustments.
* Comment and whiteline adjustments.
After the changes, we have
list_for_each_entry(link, &cont->cset_links, cset_link) {
struct css_set *cset = link->cset;
instead of
list_for_each_entry(link, &cont->css_sets, cgrp_link_list) {
struct css_set *cset = link->cg;
This patch is purely cosmetic.
v2: Fix broken sentences in the patch description.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Li Zefan <lizefan@huawei.com>
cgroup.c uses @cg for most struct css_set variables, which in itself
could be a bit confusing, but made much worse by the fact that there
are places which use @cg for struct cgroup variables.
compare_css_sets() epitomizes this confusion - @[old_]cg are struct
css_set while @cg[12] are struct cgroup.
It's not like the whole deal with cgroup, css_set and cg_cgroup_link
isn't already confusing enough. Let's give it some sanity by
uniformly using @cset for all struct css_set variables.
* s/cg/cset/ for all css_set variables.
* s/oldcg/old_cset/ s/oldcgrp/old_cgrp/. The same for the ones
prefixed with "new".
* s/cg/cgrp/ for cgroup variables in compare_css_sets().
* s/css/cset/ for the cgroup variable in task_cgroup_from_root().
* Whiteline adjustments.
This patch is purely cosmetic.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Li Zefan <lizefan@huawei.com>
Before moving tasks out of empty cpusets, update_tasks_nodemask()
is called, which calls do_migrate_pages(xx, from, to). Then those
tasks are moved to an ancestor, and do_migrate_pages() is called
again.
The first time: from = node_to_be_offlined, to = empty.
The second time: from = empty, to = ancestor's nodemask.
so looks like no pages will be migrated.
Fix this by:
- Don't call update_tasks_nodemask() on empty cpusets.
- Pass cs->old_mems_allowed to do_migrate_pages().
v4: added comment in cpuset_hotplug_update_tasks() and rephased comment
in cpuset_attach().
Signed-off-by: Li Zefan <lizefan@huawei.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Currently some cpuset behaviors are not friendly when cpuset is co-mounted
with other cgroup controllers.
Now with this patchset if cpuset is mounted with sane_behavior option,
it behaves differently:
- Tasks will be kept in empty cpusets when hotplug happens and take
masks of ancestors with non-empty cpus/mems, instead of being moved to
an ancestor.
- A task can be moved into an empty cpuset, and again it takes masks of
ancestors, so the user can drop a task into a newly created cgroup without
having to do anything for it.
As tasks can reside in empy cpusets, here're some rules:
- They can be moved to another cpuset, regardless it's empty or not.
- Though it takes masks from ancestors, it takes other configs from the
empty cpuset.
- If the ancestors' masks are changed, those tasks will also be updated
to take new masks.
v2: add documentation in include/linux/cgroup.h
Signed-off-by: Li Zefan <lizefan@huawei.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
To achieve this:
- We call update_tasks_cpumask/nodemask() for empty cpusets when
hotplug happens, instead of moving tasks out of them.
- When a cpuset's masks are changed by writing cpuset.cpus/mems,
we also update tasks in child cpusets which are empty.
v3:
- do propagation work in one place for both hotplug and unplug
v2:
- drop rcu_read_lock before calling update_task_nodemask() and
update_task_cpumask(), instead of using workqueue.
- add documentation in include/linux/cgroup.h
Signed-off-by: Li Zefan <lizefan@huawei.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
effective_cpumask_cpuset() returns an ancestor cpuset which has
non-empty cpumask.
If a cpuset is empty and the tasks in it need to update their
cpus_allowed, they take on the ancestor cpuset's cpumask.
This currently won't change any behavior, but it will later allow us
to keep tasks in empty cpusets.
Signed-off-by: Li Zefan <lizefan@huawei.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
When we update a cpuset's mems_allowed and thus update tasks'
mems_allowed, it's required to pass the old mems_allowed and new
mems_allowed to cpuset_migrate_mm().
Currently we save old mems_allowed in a temp local variable before
changing cpuset->mems_allowed. This patch changes it by saving
old mems_allowed in cpuset->old_mems_allowed.
This currently won't change any behavior, but it will later allow
us to keep tasks in empty cpusets.
v3: restored "cpuset_attach_nodemask_to = cs->mems_allowed"
Signed-off-by: Li Zefan <lizefan@huawei.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Merge misc fixes from Andrew Morton:
"Bunch of fixes and one little addition to math64.h"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (27 commits)
include/linux/math64.h: add div64_ul()
mm: memcontrol: fix lockless reclaim hierarchy iterator
frontswap: fix incorrect zeroing and allocation size for frontswap_map
kernel/audit_tree.c:audit_add_tree_rule(): protect `rule' from kill_rules()
mm: migration: add migrate_entry_wait_huge()
ocfs2: add missing lockres put in dlm_mig_lockres_handler
mm/page_alloc.c: fix watermark check in __zone_watermark_ok()
drivers/misc/sgi-gru/grufile.c: fix info leak in gru_get_config_info()
aio: fix io_destroy() regression by using call_rcu()
rtc-at91rm9200: use shadow IMR on at91sam9x5
rtc-at91rm9200: add shadow interrupt mask
rtc-at91rm9200: refactor interrupt-register handling
rtc-at91rm9200: add configuration support
rtc-at91rm9200: add match-table compile guard
fs/ocfs2/namei.c: remove unecessary ERROR when removing non-empty directory
swap: avoid read_swap_cache_async() race to deadlock while waiting on discard I/O completion
drivers/rtc/rtc-twl.c: fix missing device_init_wakeup() when booted with device tree
cciss: fix broken mutex usage in ioctl
audit: wait_for_auditd() should use TASK_UNINTERRUPTIBLE
drivers/rtc/rtc-cmos.c: fix accidentally enabling rtc channel
...
audit_add_tree_rule() must set 'rule->tree = NULL;' firstly, to protect
the rule itself freed in kill_rules().
The reason is when it is killed, the 'rule' itself may have already
released, we should not access it. one example: we add a rule to an
inode, just at the same time the other task is deleting this inode.
The work flow for adding a rule:
audit_receive() -> (need audit_cmd_mutex lock)
audit_receive_skb() ->
audit_receive_msg() ->
audit_receive_filter() ->
audit_add_rule() ->
audit_add_tree_rule() -> (need audit_filter_mutex lock)
...
unlock audit_filter_mutex
get_tree()
...
iterate_mounts() -> (iterate all related inodes)
tag_mount() ->
tag_trunk() ->
create_trunk() -> (assume it is 1st rule)
fsnotify_add_mark() ->
fsnotify_add_inode_mark() -> (add mark to inode->i_fsnotify_marks)
...
get_tree(); (each inode will get one)
...
lock audit_filter_mutex
The work flow for deleting an inode:
__destroy_inode() ->
fsnotify_inode_delete() ->
__fsnotify_inode_delete() ->
fsnotify_clear_marks_by_inode() -> (get mark from inode->i_fsnotify_marks)
fsnotify_destroy_mark() ->
fsnotify_destroy_mark_locked() ->
audit_tree_freeing_mark() ->
evict_chunk() ->
...
tree->goner = 1
...
kill_rules() -> (assume current->audit_context == NULL)
call_rcu() -> (rule->tree != NULL)
audit_free_rule_rcu() ->
audit_free_rule()
...
audit_schedule_prune() -> (assume current->audit_context == NULL)
kthread_run() -> (need audit_cmd_mutex and audit_filter_mutex lock)
prune_one() -> (delete it from prue_list)
put_tree(); (match the original get_tree above)
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Cc: Eric Paris <eparis@redhat.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
audit_log_start() does wait_for_auditd() in a loop until
audit_backlog_wait_time passes or audit_skb_queue has a room.
If signal_pending() is true this becomes a busy-wait loop, schedule() in
TASK_INTERRUPTIBLE won't block.
Thanks to Guy for fully investigating and explaining the problem.
(akpm: that'll cause the system to lock up on a non-preemptible
uniprocessor kernel)
(Guy: "Our customer was in fact running a uniprocessor machine, and they
reported a system hang.")
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Reported-by: Guy Streeter <streeter@redhat.com>
Cc: Eric Paris <eparis@redhat.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The dmesg_restrict sysctl currently covers the syslog method for access
dmesg, however /dev/kmsg isn't covered by the same protections. Most
people haven't noticed because util-linux dmesg(1) defaults to using the
syslog method for access in older versions. With util-linux dmesg(1)
defaults to reading directly from /dev/kmsg.
To fix /dev/kmsg, let's compare the existing interfaces and what they
allow:
- /proc/kmsg allows:
- open (SYSLOG_ACTION_OPEN) if CAP_SYSLOG since it uses a destructive
single-reader interface (SYSLOG_ACTION_READ).
- everything, after an open.
- syslog syscall allows:
- anything, if CAP_SYSLOG.
- SYSLOG_ACTION_READ_ALL and SYSLOG_ACTION_SIZE_BUFFER, if
dmesg_restrict==0.
- nothing else (EPERM).
The use-cases were:
- dmesg(1) needs to do non-destructive SYSLOG_ACTION_READ_ALLs.
- sysklog(1) needs to open /proc/kmsg, drop privs, and still issue the
destructive SYSLOG_ACTION_READs.
AIUI, dmesg(1) is moving to /dev/kmsg, and systemd-journald doesn't
clear the ring buffer.
Based on the comments in devkmsg_llseek, it sounds like actions besides
reading aren't going to be supported by /dev/kmsg (i.e.
SYSLOG_ACTION_CLEAR), so we have a strict subset of the non-destructive
syslog syscall actions.
To this end, move the check as Josh had done, but also rename the
constants to reflect their new uses (SYSLOG_FROM_CALL becomes
SYSLOG_FROM_READER, and SYSLOG_FROM_FILE becomes SYSLOG_FROM_PROC).
SYSLOG_FROM_READER allows non-destructive actions, and SYSLOG_FROM_PROC
allows destructive actions after a capabilities-constrained
SYSLOG_ACTION_OPEN check.
- /dev/kmsg allows:
- open if CAP_SYSLOG or dmesg_restrict==0
- reading/polling, after open
Addresses https://bugzilla.redhat.com/show_bug.cgi?id=903192
[akpm@linux-foundation.org: use pr_warn_once()]
Signed-off-by: Kees Cook <keescook@chromium.org>
Reported-by: Christian Kujau <lists@nerdbynature.de>
Tested-by: Josh Boyer <jwboyer@redhat.com>
Cc: Kay Sievers <kay@vrfy.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We recently noticed that reboot of a 1024 cpu machine takes approx 16
minutes of just stopping the cpus. The slowdown was tracked to commit
f96972f2dc ("kernel/sys.c: call disable_nonboot_cpus() in
kernel_restart()").
The current implementation does all the work of hot removing the cpus
before halting the system. We are switching to just migrating to the
boot cpu and then continuing with shutdown/reboot.
This also has the effect of not breaking x86's command line parameter
for specifying the reboot cpu. Note, this code was shamelessly copied
from arch/x86/kernel/reboot.c with bits removed pertaining to the
reboot_cpu command line parameter.
Signed-off-by: Robin Holt <holt@sgi.com>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Cc: "Srivatsa S. Bhat" <srivatsa.bhat@linux.vnet.ibm.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Russ Anderson <rja@sgi.com>
Cc: Robin Holt <holt@sgi.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are instances in the kernel where we would like to disable CPU
hotplug (from sysfs) during some important operation. Today the freezer
code depends on this and the code to do it was kinda tailor-made for
that.
Restructure the code and make it generic enough to be useful for other
usecases too.
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Robin Holt <holt@sgi.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Russ Anderson <rja@sgi.com>
Cc: Robin Holt <holt@sgi.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Nothing about the sched_clock implementation in the ARM port is
specific to the architecture. Generalize the code so that other
architectures can use it by selecting GENERIC_SCHED_CLOCK.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
[jstultz: Merge minor collisions with other patches in my tree]
Signed-off-by: John Stultz <john.stultz@linaro.org>
Export symbols so they can be used by
drivers/staging/android/alarm-dev.c if it is built as a module.
So far alarm-dev is built-in but module support is planned (see
drivers/staging/android/TODO).
Signed-off-by: Marcus Gelderie <redmnic@gmail.com>
[jstultz: tweaked commit message, also export newly added functions]
Signed-off-by: John Stultz <john.stultz@linaro.org>
one of the counter clocks. The new multibuffer code changed the trace_clock
file to update the trace instances tr->clock_id but the actual traces still
used the value from the obsolete global variable trace_clock_id.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJRt8hEAAoJEOdOSU1xswtM6+EH/jAEuOrXhkkDqcua/paAOngw
XWSaF9Cr6ozh4hutFrVSBi3AnsDrVo0adZmMVvLS9a7goyIUdYLfXbNeyK6Nvcq5
bGXR5sJNpjtQ7snrmGX2KlXIGix28adi49eACi4qsGSG/jJYORYlgXcNBeXtENsb
PKTXdQ8XEyc/h7Q51YQPHIVunf+zJSoepuXZ0myPLUWzLlPX9qoy5kETEpGhh9xh
Ianb4wLo8dn6JuVGBuXQhZ/VzUHwJT1jJxR2JfnZ0bNVplNilnumAxY8f2zPOmzT
lvIiQjCMRvNExFShuFh9WNnGRi62zYE9e0JJpYL4W9moIcbbEUvXYt2/imAVe9Q=
=H+Wb
-----END PGP SIGNATURE-----
Merge tag 'trace-fixes-v3.10-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fix from Steven Rostedt:
"Yoshihiro Yunomae fixed a regression in the output format when using
one of the counter clocks.
The new multibuffer code changed the trace_clock file to update the
trace instances tr->clock_id but the actual traces still used the
value from the obsolete global variable trace_clock_id"
* tag 'trace-fixes-v3.10-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Fix outputting formats of x86-tsc and counter when use trace_clock
The function tracer uses preempt_disable/enable_notrace() for
synchronization between reading registered ftrace_ops and unregistering
them.
Most of the ftrace_ops are global permanent structures that do not
require this synchronization. That is, ops may be added and removed from
the hlist but are never freed, and wont hurt if a synchronization is
missed.
But this is not true for dynamically created ftrace_ops or control_ops,
which are used by the perf function tracing.
The problem here is that the function tracer can be used to trace
kernel/user context switches as well as going to and from idle.
Basically, it can be used to trace blind spots of the RCU subsystem.
This means that even though preempt_disable() is done, a
synchronize_sched() will ignore CPUs that haven't made it out of user
space or idle. These can include functions that are being traced just
before entering or exiting the kernel sections.
To implement the RCU synchronization, instead of using
synchronize_sched() the use of schedule_on_each_cpu() is performed. This
means that when a dynamically allocated ftrace_ops, or a control ops is
being unregistered, all CPUs must be touched and execute a ftrace_sync()
stub function via the work queues. This will rip CPUs out from idle or
in dynamic tick mode. This only happens when a user disables perf
function tracing or other dynamically allocated function tracers, but it
allows us to continue to debug RCU and context tracking with function
tracing.
Link: http://lkml.kernel.org/r/1369785676.15552.55.camel@gandalf.local.home
Cc: "Paul E. McKenney" <paulmck@us.ibm.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Commit 4f271a2a60
(tracing: Add a proc file to stop tracing and free buffer)
implement a method to free up ring buffer in kernel memory
in the release code path of free_buffer's fd.
Then we don't need read/write support for free_buffer,
indeed we just have a dummy write fop, and don't implement read fop.
So the 0200 is more reasonable file mode for free_buffer than
the current file mode 0644.
Link: http://lkml.kernel.org/r/20130526085201.GA3183@udknight
Acked-by: Vaibhav Nagarnaik <vnagarnaik@google.com>
Acked-by: David Sharp <dhsharp@google.com>
Signed-off-by: Wang YanQing <udknight@gmail.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Add the "cpudump" command to have the current CPU ftrace buffer dumped
to console if a function is hit. This is useful when debugging a
tripple fault, where you have an idea of a function that is called
just before the tripple fault occurs, and can tell ftrace to dump its
content out to the console before it continues.
This differs from the "dump" command as it only dumps the content of
the ring buffer for the currently executing CPU, and does not show
the contents of the other CPUs.
Format is:
<function>:cpudump
echo 'bad_address:cpudump' > /debug/tracing/set_ftrace_filter
To remove this:
echo '!bad_address:cpudump' > /debug/tracing/set_ftrace_filter
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Add the "dump" command to have the ftrace buffer dumped to console if
a function is hit. This is useful when debugging a tripple fault,
where you have an idea of a function that is called just before the
tripple fault occurs, and can tell ftrace to dump its content out
to the console before it continues.
Format is:
<function>:dump
echo 'bad_address:dump' > /debug/tracing/set_ftrace_filter
To remove this:
echo '!bad_address:dump' > /debug/tracing/set_ftrace_filter
Requested-by: Luis Claudio R. Goncalves <lclaudio@uudg.org>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
This adds in a new message to the wakeup code which adds an
indication to the log that suspend was cancelled due to a wake event
occouring during the suspend sequence. It also adjusts the message
printed in suspend.c to reflect the potential that a suspend was
aborted, as opposed to a device failing to suspend.
Without these message adjustments one can end up with a kernel log
that says that a device failed to suspend with no actual device
suspend failures, which can be confusing to the log examiner.
Signed-off-by: Bernie Thompson <bhthompson@chromium.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Moving x86 to the generic idle implementation (commit 7d1a9417 "x86:
Use generic idle loop") wreckaged the stack protector.
I stupidly missed that boot_init_stack_canary() must be inlined from a
function which never returns, but I put that call into
arch_cpu_idle_prepare() which of course returns.
I pondered to play tricks with arch_cpu_idle_prepare() first, but then
I noticed, that the other archs which have implemented the
stackprotector (ARM and SH) do not initialize the canary for the
non-boot cpus.
So I decided to move the boot_init_stack_canary() call into
cpu_startup_entry() ifdeffed with an CONFIG_X86 for now. This #ifdef
is just a temporary measure as I don't want to inflict the
boot_init_stack_canary() call on ARM and SH that late in the cycle.
I'll queue a patch for 3.11 which removes the #ifdef if the ARM/SH
maintainers have no objection.
Reported-by: Wouter van Kesteren <woutershep@gmail.com>
Cc: x86@kernel.org
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Outputting formats of x86-tsc and counter should be a raw format, but after
applying the patch(2b6080f28c), the format was
changed to nanosec. This is because the global variable trace_clock_id was used.
When we use multiple buffers, clock_id of each sub-buffer should be used. Then,
this patch uses tr->clock_id instead of the global variable trace_clock_id.
[ Basically, this fixes a regression where the multibuffer code changed the
trace_clock file to update tr->clock_id but the traces still use the old
global trace_clock_id variable, negating the file's effect. The global
trace_clock_id variable is obsolete and removed. - SR ]
Link: http://lkml.kernel.org/r/20130423013239.22334.7394.stgit@yunodevel
Signed-off-by: Yoshihiro YUNOMAE <yoshihiro.yunomae.ez@hitachi.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
When a threaded irq handler is installed the irq thread is initially
created on normal scheduling priority. Only after the irq thread is
woken up it sets its priority to RT_FIFO MAX_USER_RT_PRIO/2 itself.
This means that interrupts that occur directly after the irq handler
is installed will be handled on a normal scheduling priority instead
of the realtime priority that one would expect.
Fix this by setting the RT priority on creation of the irq_thread.
Signed-off-by: Ivo Sieben <meltedpianoman@gmail.com>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Steven Rostedt <rostedt@goodmis.org>
Link: http://lkml.kernel.org/r/1370254322-17240-1-git-send-email-meltedpianoman@gmail.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The stop machine logic can lock up if all but one of the migration
threads make it through the disable-irq step and the one remaining
thread gets stuck in __do_softirq. The reason __do_softirq can hang is
that it has a bail-out based on jiffies timeout, but in the lockup case,
jiffies itself is not incremented.
To work around this, re-add the max_restart counter in __do_irq and stop
processing irqs after 10 restarts.
Thanks to Tejun Heo and Rusty Russell and others for helping me track
this down.
This was introduced in 3.9 by commit c10d73671a ("softirq: reduce
latencies").
It may be worth looking into ath9k to see if it has issues with its irq
handler at a later date.
The hang stack traces look something like this:
------------[ cut here ]------------
WARNING: at kernel/watchdog.c:245 watchdog_overflow_callback+0x9c/0xa7()
Watchdog detected hard LOCKUP on cpu 2
Modules linked in: ath9k ath9k_common ath9k_hw ath mac80211 cfg80211 nfsv4 auth_rpcgss nfs fscache nf_nat_ipv4 nf_nat veth 8021q garp stp mrp llc pktgen lockd sunrpc]
Pid: 23, comm: migration/2 Tainted: G C 3.9.4+ #11
Call Trace:
<NMI> warn_slowpath_common+0x85/0x9f
warn_slowpath_fmt+0x46/0x48
watchdog_overflow_callback+0x9c/0xa7
__perf_event_overflow+0x137/0x1cb
perf_event_overflow+0x14/0x16
intel_pmu_handle_irq+0x2dc/0x359
perf_event_nmi_handler+0x19/0x1b
nmi_handle+0x7f/0xc2
do_nmi+0xbc/0x304
end_repeat_nmi+0x1e/0x2e
<<EOE>>
cpu_stopper_thread+0xae/0x162
smpboot_thread_fn+0x258/0x260
kthread+0xc7/0xcf
ret_from_fork+0x7c/0xb0
---[ end trace 4947dfa9b0a4cec3 ]---
BUG: soft lockup - CPU#1 stuck for 22s! [migration/1:17]
Modules linked in: ath9k ath9k_common ath9k_hw ath mac80211 cfg80211 nfsv4 auth_rpcgss nfs fscache nf_nat_ipv4 nf_nat veth 8021q garp stp mrp llc pktgen lockd sunrpc]
irq event stamp: 835637905
hardirqs last enabled at (835637904): __do_softirq+0x9f/0x257
hardirqs last disabled at (835637905): apic_timer_interrupt+0x6d/0x80
softirqs last enabled at (5654720): __do_softirq+0x1ff/0x257
softirqs last disabled at (5654725): irq_exit+0x5f/0xbb
CPU 1
Pid: 17, comm: migration/1 Tainted: G WC 3.9.4+ #11 To be filled by O.E.M. To be filled by O.E.M./To be filled by O.E.M.
RIP: tasklet_hi_action+0xf0/0xf0
Process migration/1
Call Trace:
<IRQ>
__do_softirq+0x117/0x257
irq_exit+0x5f/0xbb
smp_apic_timer_interrupt+0x8a/0x98
apic_timer_interrupt+0x72/0x80
<EOI>
printk+0x4d/0x4f
stop_machine_cpu_stop+0x22c/0x274
cpu_stopper_thread+0xae/0x162
smpboot_thread_fn+0x258/0x260
kthread+0xc7/0xcf
ret_from_fork+0x7c/0xb0
Signed-off-by: Ben Greear <greearb@candelatech.com>
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: Pekka Riikonen <priikone@iki.fi>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
TINY_RCU's reset_cpu_stall_ticks() and check_cpu_stalls() functions
are defined unconditionally, and are empty functions if CONFIG_RCU_TRACE
is disabled (which in turns disables detection of RCU CPU stalls).
This commit saves a few lines of source code by defining these functions
only if CONFIG_RCU_TRACE=y.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Now that TINY_PREEMPT_RCU is no more, exit_rcu() is always an empty
function. But if TINY_RCU is going to have an empty function, it should
be in include/linux/rcutiny.h, where it does not bloat the kernel.
This commit therefore moves exit_rcu() out of kernel/rcupdate.c to
kernel/rcutree_plugin.h, and places a static inline empty function in
include/linux/rcutiny.h in order to shrink TINY_RCU a bit.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
This commit rearranges code in order to allow ifdefs to be consolidated
in kernel/rcutiny_plugin.h, simplifying the code.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
With the removal of CONFIG_TINY_PREEMPT_RCU, check_cpu_stall_preempt()
is now an empty function. This commit therefore eliminates it by
inlining it.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
TINY_PREEMPT_RCU could use a kthread to handle RCU callback invocation,
which required an API to abstract kthread vs. softirq invocation.
Now that TINY_PREEMPT_RCU is no longer with us, this commit retires
this API in favor of direct use of the relevant softirq primitives.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
With the removal of CONFIG_TINY_PREEMPT_RCU, rcu_preempt_process_callbacks()
is now an empty function. This commit therefore eliminates it by
inlining it.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
With the removal of CONFIG_TINY_PREEMPT_RCU, rcu_preempt_remove_callbacks()
is now an empty function. This commit therefore eliminates it by
inlining it.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
With the removal of CONFIG_TINY_PREEMPT_RCU, rcu_preempt_check_callbacks()
is now an empty function. This commit therefore eliminates it by
inlining it.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
With the removal of CONFIG_TINY_PREEMPT_RCU, show_tiny_preempt_stats()
is now an empty function. This commit therefore eliminates it by
inlining it.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
TINY_PREEMPT_RCU adds significant code and complexity, but does not
offer commensurate benefits. People currently using TINY_PREEMPT_RCU
can get much better memory footprint with TINY_RCU, or, if they really
need preemptible RCU, they can use TREE_PREEMPT_RCU with a relatively
minor degradation in memory footprint. Please note that this move
has been widely publicized on LKML (https://lkml.org/lkml/2012/11/12/545)
and on LWN (http://lwn.net/Articles/541037/).
This commit therefore removes TINY_PREEMPT_RCU.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
[ paulmck: Updated to eliminate #else in rcutiny.h as suggested by Josh ]
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
These interfaces never did get used, so this commit removes them,
their rcutorture tests, and documentation referencing them.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Two ifdefs in kernel/rcupdate.c now have identical conditions with
nothing between them, so the commit merges them into a single ifdef.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Systems with HZ=100 can have slow bootup times due to the default
three-jiffy delays between quiescent-state forcing attempts. This
commit therefore auto-tunes the RCU_JIFFIES_TILL_FORCE_QS value based
on the value of HZ. However, this would break very large systems that
require more time between quiescent-state forcing attempts. This
commit therefore also ups the default delay by one jiffy for each
256 CPUs that might be on the system (based off of nr_cpu_ids at
runtime, -not- NR_CPUS at build time).
Updated to collapse #ifdefs for RCU_JIFFIES_TILL_FORCE_QS into a
step-function definition as suggested by Josh Triplett.
Reported-by: Paul Mackerras <paulus@au1.ibm.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
After a release or two, features are no longer experimental. Therefore,
this commit removes the "Experimental" tag from them.
Reported-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
The __rcu_process_callbacks() invokes note_gp_changes() immediately
before invoking rcu_check_quiescent_state(), which conditionally
invokes that same function. This commit therefore eliminates the
call to note_gp_changes() in __rcu_process_callbacks() in favor of
making unconditional to call from rcu_check_quiescent_state() to
note_gp_changes().
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Given the changes that introduce note_gp_change(), rcu_start_gp_per_cpu()
is now a trivial wrapper function with only one caller. This commit
therefore inlines it into its sole call site.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
One of the calls to check_for_new_grace_period() is now redundant due to
an immediately preceding call to note_gp_changes(). Eliminating this
redundant call leaves a single caller, which is simpler if inlined.
This commit therefore eliminates the redundant call and inlines the
body of check_for_new_grace_period() into the single remaining call site.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
This commit eliminates some duplicated code by merging
__rcu_process_gp_end() into __note_gp_changes().
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Because note_gp_changes() now incorporates rcu_process_gp_end() function,
this commit switches to the former and eliminates the latter. In
addition, this commit changes external calls from __rcu_process_gp_end()
to __note_gp_changes().
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
This commit converts printk() calls to the corresponding pr_*() calls.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Because note_new_gpnum() now also checks for the ends of old grace periods,
this commit changes its name to note_gp_changes(). Later commits will merge
rcu_process_gp_end() into note_gp_changes().
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
The current implementation can detect the beginning of a new grace period
before noting the end of a previous grace period. Although the current
implementation correctly handles this sort of nonsense, it would be
good to reduce RCU's state space by making such nonsense unnecessary,
which is now possible thanks to the fact that RCU's callback groups are
now numbered.
This commit therefore makes __note_new_gpnum() invoke
__rcu_process_gp_end() in order to note the ends of prior grace
periods before noting the beginnings of new grace periods.
Of course, this now means that note_new_gpnum() notes both the
beginnings and ends of grace periods, and could therefore be
used in place of rcu_process_gp_end(). But that is a job for
later commits.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
The addition of callback numbering allows combining the detection of the
ends of old grace periods and the beginnings of new grace periods. This
commit moves code to set the stage for this combining.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
This commit converts printk() calls to the corresponding pr_*() calls.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
This patch increases the amount of output produced by the
irq_domain_mapping debugfs file by first listing all of the registered
irq domains at the beginning of the output, and then by including all
mapped IRQs in the output, not just the active ones. It is very useful
when debugging irqdomain issues to be able to see the entire list of
mapped irqs, not just the ones that happen to be connected to devices.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
After refactoring the irqdomain code, there are a number of API
functions that are merely empty wrappers around core code. Drop those
wrappers out of the C file and replace them with static inlines in the
header.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
The NOMAP irq_domain type is only used by a handful of interrupt
controllers and it unnecessarily complicates the code by adding special
cases on how to look up mappings and different revmap functions are used
for each type which need to validate the correct type is passed to it
before performing the reverse map. Eliminating the revmap_type and
making a single reverse mapping function simplifies the code. It also
shouldn't be any slower than having separate revmap functions because
the type of the revmap needed to be checked anyway.
The linear and tree revmap types were already merged in a previous
patch. This patch rolls the NOMAP or direct mapping behaviour into the
same domain code making is possible for an irq domain to do any mapping
type; linear, tree or direct; and that the mapping will be transparent
to the interrupt controller driver.
With this change, direct mappings will get stored in the linear or tree
mapping for consistency. Reverse mapping from the hwirq to virq will go
through the normal lookup process. However, any controller using a
direct mapping can take advantage of knowing that hwirq==virq for any
mapped interrupts skip doing a revmap lookup when handling IRQs.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Keeping them separate makes irq_domain more complex and adds a lot of
code (as proven by the diffstat). Merging them simplifies the whole
scheme. This change makes it so both the tree and linear methods can be
used by the same irq_domain instance. If the hwirq is less than the
->linear_size, then the linear map is used to reverse map the hwirq.
Otherwise the radix tree is used. The test for which map to use is no
more expensive that the existing code, so the performance of fast path
is preserved.
It also means that complex interrupt controllers can use both the
linear map and a tree in the same domain. This may be useful for an
interrupt controller with a base set of core irqs and a large number
of GPIOs which might be used as irqs. The linear map could cover the
core irqs, and the tree used for thas irqs. The linear map could
cover the core irqs, and the tree used for the gpios.
v2: Drop reorganization of revmap data
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Rob Herring <rob.herring@calxeda.com>
This patch adds a name field to the irq_domain structure to help mere
mortals understand the mappings between irq domains and virqs. It also
converts a number of places that have open-coded some kind of fudging
an irqdomain name to use the new field. This means a more consistent
display of names in irq domain log messages and debugfs output.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
The LEGACY mapping unnecessarily complicates the irqdomain code and
can easily be implemented with a linear mapping. By ripping it out
and replacing it with the LINEAR mapping the object size of
irqdomain.c shrinks by about 330 bytes (ARMv7) which offsets the
additional allocation required by the linear map. It also makes it
possible for current LEGACY map users to pre-allocate irq_descs for a
subset of the hwirqs and dynamically allocate the rest as needed.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Rob Herring <rob.herring@calxeda.com>
Commit 98aa468e, "irqdomain: Support for static IRQ mapping and
association" introduced an API for directly associating blocks of hwirqs
to linux irqs. However, if any irq in that block failed to map (say if
the mapping functions returns an error because the irq is already
mapped) then the whole thing will fail and roll back. This is probably
too aggressive since there are valid reasons why a mapping may fail.
ie. Firmware may have a particular IRQ marked as unusable.
This patch drops the error path out of irq_domain_associate(). If a
mapping fails, then it is simply skipped. There is no reason to fail the
entire allocation.
v2: Still output an information message on failed mappings and make sure
attempted mapping gets cleared out of the irq_data structure.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
As we can drop rcu read lock while iterating cgroup hierarchy,
we don't have to do propagation asynchronously via workqueue.
Signed-off-by: Li Zefan <lizefan@huawei.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Instead of triggering propagation work in cpuset_attach(), we make
hotplug propagation work wait until there's no task attaching in
progress.
IMO this is more robust. We won't see empty masks in cpuset_attach().
Also it's a preparation for removing propagation work. Without asynchronous
propagation we can't call move_tasks_in_empty_cpuset() in cpuset_attach(),
because otherwise we'll deadlock on cgroup_mutex.
tj: typo fixes.
Signed-off-by: Li Zefan <lizefan@huawei.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Pull timer fixes from Thomas Gleixner:
- Trivial: unused variable removal
- Posix-timers: Add the clock ID to the new proc interface to make it
useful. The interface is new and should be functional when we reach
the final 3.10 release.
- Cure a false positive warning in the tick code introduced by the
overhaul in 3.10
- Fix for a persistent clock detection regression introduced in this
cycle
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
timekeeping: Correct run-time detection of persistent_clock.
ntp: Remove unused variable flags in __hardpps
posix-timers: Show clock ID in proc file
tick: Cure broadcast false positive pending bit warning
This branch contains a set of straight forward bug fixes to the
irqdomain code and to a couple of drivers that make use of it.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=wZCk
-----END PGP SIGNATURE-----
Merge tag 'irqdomain-for-linus' of git://git.secretlab.ca/git/linux
Pull irqdomain bug fixes from Grant Likely:
"This branch contains a set of straight forward bug fixes to the
irqdomain code and to a couple of drivers that make use of it."
* tag 'irqdomain-for-linus' of git://git.secretlab.ca/git/linux:
irqchip: Return -EPERM for reserved IRQs
irqdomain: document the simple domain first_irq
kernel/irq/irqdomain.c: before use 'irq_data', need check it whether valid.
irqdomain: export irq_domain_add_simple
The first_irq needs to be zero to get a linear domain and that
comes with special semantics. We want to simplify this going
forward but some documentation never hurts.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Since irq_data may be NULL, if so, we WARN_ON(), and continue, 'hwirq'
which related with 'irq_data' has to initialize later, or it will cause
issue.
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
All other irq_domain_add_* functions are exported already, and apparently
this one got left out by mistake, which causes build errors for ARM
allmodconfig kernels:
ERROR: "irq_domain_add_simple" [drivers/gpio/gpio-rcar.ko] undefined!
ERROR: "irq_domain_add_simple" [drivers/gpio/gpio-em.ko] undefined!
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
The first two fix the case where full RCU debugging is enabled, enabling
function tracing causes a live lock of the system. This is due to the added
debug checks in rcu_dereference_raw() that is used by the function tracer.
These checks are also traced by the function tracer as well as cause enough
overhead to the function tracer to slow down the system enough that
the time to finish an interrupt can take longer than when the next
interrupt is triggered, causing a live lock from the timer interrupt.
Talking this over with Paul McKenney, we came up with a fix that adds
a new rcu_dereference_raw_notrace() that does not perform these added checks,
and let the function tracer use that.
The third commit fixes a failed compile when branch tracing is enabled,
due to the conversion of the trace_test_buffer() selftest that the
branch trace wasn't converted for.
The forth patch fixes a bug caught by the RCU lockdep code where a
rcu_read_lock() is performed when rcu is disabled (either going to
or from idle, or user space). This happened on the irqsoff tracer
as it calls task_uid(). The fix here was to use current_uid() when
possible that doesn't use rcu locking. Which luckily, is always used
when irqsoff calls this code.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJRsQZhAAoJEOdOSU1xswtMquIH/0zyrqrLTnkc5MsNnnJ8kH5R
z1cULts4FqBTUNZ1hdb3BTOu4zywjREIkWfM9qqpBmq9Mq6PBxX7gxWTqYvD4jiX
EatiiCKa7Fyddx4iHJNfvtWgKVYt9WKSNeloRugS9h7NxIZ1wpz21DUpENFQzW2f
jWRnq/AKXFmZ0vn1953mPePtRsg61RYpb7DCkTE1gtUnvL43wMd/Mo6p6BLMEG26
1dDK6EWO/uewl8A4oP5JZYP+AP5Ckd4x1PuQK682AtQw+8S6etaGfeJr0WZmKQoD
0aDZ/NXXSNKChlUFGJusBNJCWryONToa+sdiKuk1h/lW/k9Mail/FChiHBzMiwk=
=uvlD
-----END PGP SIGNATURE-----
Merge tag 'trace-fixes-v3.10-rc3-v3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fixes from Steven Rostedt:
"This contains 4 fixes.
The first two fix the case where full RCU debugging is enabled,
enabling function tracing causes a live lock of the system. This is
due to the added debug checks in rcu_dereference_raw() that is used by
the function tracer. These checks are also traced by the function
tracer as well as cause enough overhead to the function tracer to slow
down the system enough that the time to finish an interrupt can take
longer than when the next interrupt is triggered, causing a live lock
from the timer interrupt.
Talking this over with Paul McKenney, we came up with a fix that adds
a new rcu_dereference_raw_notrace() that does not perform these added
checks, and let the function tracer use that.
The third commit fixes a failed compile when branch tracing is
enabled, due to the conversion of the trace_test_buffer() selftest
that the branch trace wasn't converted for.
The forth patch fixes a bug caught by the RCU lockdep code where a
rcu_read_lock() is performed when rcu is disabled (either going to or
from idle, or user space). This happened on the irqsoff tracer as it
calls task_uid(). The fix here was to use current_uid() when possible
that doesn't use rcu locking. Which luckily, is always used when
irqsoff calls this code."
* tag 'trace-fixes-v3.10-rc3-v3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Use current_uid() for critical time tracing
tracing: Fix bad parameter passed in branch selftest
ftrace: Use the rcu _notrace variants for rcu_dereference_raw() and friends
rcu: Add _notrace variation of rcu_dereference_raw() and hlist_for_each_entry_rcu()
When param1 is enabled in EINJ but not assigned with a valid
value, sometimes it will cause the error like below:
APEI: Can not request [mem 0x7aaa7000-0x7aaa7007] for APEI EINJ Trigger registers
It is because some firmware will access target address specified in
param1 to trigger the error when injecting memory error. This will
cause resource conflict with regular memory. So It must be removed
from trigger table resources, but incorrect param1/param2
combination will stop this action. Add extra check to avoid
this kind of error.
Signed-off-by: Chen Gong <gong.chen@linux.intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The irqsoff tracer records the max time that interrupts are disabled.
There are hooks in the assembly code that calls back into the tracer when
interrupts are disabled or enabled.
When they are enabled, the tracer checks if the amount of time they
were disabled is larger than the previous recorded max interrupts off
time. If it is, it creates a snapshot of the currently running trace
to store where the last largest interrupts off time was held and how
it happened.
During testing, this RCU lockdep dump appeared:
[ 1257.829021] ===============================
[ 1257.829021] [ INFO: suspicious RCU usage. ]
[ 1257.829021] 3.10.0-rc1-test+ #171 Tainted: G W
[ 1257.829021] -------------------------------
[ 1257.829021] /home/rostedt/work/git/linux-trace.git/include/linux/rcupdate.h:780 rcu_read_lock() used illegally while idle!
[ 1257.829021]
[ 1257.829021] other info that might help us debug this:
[ 1257.829021]
[ 1257.829021]
[ 1257.829021] RCU used illegally from idle CPU!
[ 1257.829021] rcu_scheduler_active = 1, debug_locks = 0
[ 1257.829021] RCU used illegally from extended quiescent state!
[ 1257.829021] 2 locks held by trace-cmd/4831:
[ 1257.829021] #0: (max_trace_lock){......}, at: [<ffffffff810e2b77>] stop_critical_timing+0x1a3/0x209
[ 1257.829021] #1: (rcu_read_lock){.+.+..}, at: [<ffffffff810dae5a>] __update_max_tr+0x88/0x1ee
[ 1257.829021]
[ 1257.829021] stack backtrace:
[ 1257.829021] CPU: 3 PID: 4831 Comm: trace-cmd Tainted: G W 3.10.0-rc1-test+ #171
[ 1257.829021] Hardware name: To Be Filled By O.E.M. To Be Filled By O.E.M./To be filled by O.E.M., BIOS SDBLI944.86P 05/08/2007
[ 1257.829021] 0000000000000001 ffff880065f49da8 ffffffff8153dd2b ffff880065f49dd8
[ 1257.829021] ffffffff81092a00 ffff88006bd78680 ffff88007add7500 0000000000000003
[ 1257.829021] ffff88006bd78680 ffff880065f49e18 ffffffff810daebf ffffffff810dae5a
[ 1257.829021] Call Trace:
[ 1257.829021] [<ffffffff8153dd2b>] dump_stack+0x19/0x1b
[ 1257.829021] [<ffffffff81092a00>] lockdep_rcu_suspicious+0x109/0x112
[ 1257.829021] [<ffffffff810daebf>] __update_max_tr+0xed/0x1ee
[ 1257.829021] [<ffffffff810dae5a>] ? __update_max_tr+0x88/0x1ee
[ 1257.829021] [<ffffffff811002b9>] ? user_enter+0xfd/0x107
[ 1257.829021] [<ffffffff810dbf85>] update_max_tr_single+0x11d/0x12d
[ 1257.829021] [<ffffffff811002b9>] ? user_enter+0xfd/0x107
[ 1257.829021] [<ffffffff810e2b15>] stop_critical_timing+0x141/0x209
[ 1257.829021] [<ffffffff8109569a>] ? trace_hardirqs_on+0xd/0xf
[ 1257.829021] [<ffffffff811002b9>] ? user_enter+0xfd/0x107
[ 1257.829021] [<ffffffff810e3057>] time_hardirqs_on+0x2a/0x2f
[ 1257.829021] [<ffffffff811002b9>] ? user_enter+0xfd/0x107
[ 1257.829021] [<ffffffff8109550c>] trace_hardirqs_on_caller+0x16/0x197
[ 1257.829021] [<ffffffff8109569a>] trace_hardirqs_on+0xd/0xf
[ 1257.829021] [<ffffffff811002b9>] user_enter+0xfd/0x107
[ 1257.829021] [<ffffffff810029b4>] do_notify_resume+0x92/0x97
[ 1257.829021] [<ffffffff8154bdca>] int_signal+0x12/0x17
What happened was entering into the user code, the interrupts were enabled
and a max interrupts off was recorded. The trace buffer was saved along with
various information about the task: comm, pid, uid, priority, etc.
The uid is recorded with task_uid(tsk). But this is a macro that uses rcu_read_lock()
to retrieve the data, and this happened to happen where RCU is blind (user_enter).
As only the preempt and irqs off tracers can have this happen, and they both
only have the tsk == current, if tsk == current, use current_uid() instead of
task_uid(), as current_uid() does not use RCU as only current can change its uid.
This fixes the RCU suspicious splat.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Check if cpus_allowed is to be changed before calling validate_change().
This won't change any behavior, but later it will allow us to do this:
# mkdir /cpuset/child
# echo $$ > /cpuset/child/tasks /* empty cpuset */
# echo > /cpuset/child/cpuset.cpus /* do nothing, won't fail */
Without this patch, the last operation will fail.
Signed-off-by: Li Zefan <lizefan@huawei.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
- We never pass a NULL @cs to these functions.
- The top cpuset always has some online cpus/mems.
Signed-off-by: Li Zefan <lizefan@huawei.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
* Rename it from files[] (really?) to cgroup_base_files[].
* Drop CGROUP_FILE_GENERIC_PREFIX which was defined as "cgroup." and
used inconsistently. Just use "cgroup." directly.
* Collect insane files at the end. Note that only the insane ones are
missing "cgroup." prefix.
This patch doesn't introduce any functional changes.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Li Zefan <lizefan@huawei.com>
The empty cgroup notification mechanism currently implemented in
cgroup is tragically outdated. Forking and execing userland process
stopped being a viable notification mechanism more than a decade ago.
We're gonna have a saner mechanism. Let's make it clear that this
abomination is going away.
Mark "notify_on_release" and "release_agent" with CFTYPE_INSANE.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Li Zefan <lizefan@huawei.com>
Some resources controlled by cgroup aren't per-task and cgroup core
allowing threads of a single thread_group to be in different cgroups
forced memcg do explicitly find the group leader and use it. This is
gonna be nasty when transitioning to unified hierarchy and in general
we don't want and won't support granularity finer than processes.
Mark "tasks" with CFTYPE_INSANE.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Li Zefan <lizefan@huawei.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Balbir Singh <bsingharora@gmail.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: cgroups@vger.kernel.org
Cc: Vivek Goyal <vgoyal@redhat.com>
Ever since commit 45f035ab9b ("CONFIG_HOTPLUG should be always on"),
it has been basically impossible to build a kernel with CONFIG_HOTPLUG
turned off. Remove all the remaining references to it.
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Doug Thompson <dougthompson@xmission.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Print physical address info in a style consistent with the %pR style
used elsewhere in the kernel.
Commit 69f1d475cc did this for a similar printk in this file, but I
must have missed this one.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull cgroup fixes from Tejun Heo:
- Fix for yet another xattr bug which may lead to NULL deref.
- A subtle bug in for_each_descendant_pre(). This bug requires quite
specific conditions to trigger and isn't too likely to actually
happen in the wild, but maybe that just makes it that much more
nastier.
- A warning message added for silly cgroup re-mount (not -o remount,
but unmount followed by mount) behavior.
* 'for-3.10-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
cgroup: warn about mismatching options of a new mount of an existing hierarchy
cgroup: fix a subtle bug in descendant pre-order walk
cgroup: initialize xattr before calling d_instantiate()
Since 7300711e ("clockevents: broadcast fixup possible waiters"),
the timekeeping duty is assigned to the CPU that handles the tick
broadcast clock device by the time it is set in one shot mode.
This is an issue in full dynticks mode where the timekeeping duty
must stay handled by the boot CPU for now. Otherwise it prevents
secondary CPUs from offlining and this breaks
suspend/shutdown/reboot/...
As it appears there is no reason for this timekeeping duty to be
moved to the broadcast CPU, besides nothing prevent it from being
later re-assigned to another target, let's simply remove it.
Signed-off-by: Jiri Bohac <jbohac@suse.cz>
Reported-by: Steven Rostedt <rostedt@goodmis.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Commit 78becc2709 ("sched: Use an accessor to read the rq clock")
introduces rq_clock(), which obsoletes the use of the "rq" variable
in expire_cfs_rq_runtime() and triggers this build warning:
kernel/sched/fair.c: In function 'expire_cfs_rq_runtime':
kernel/sched/fair.c:2159:13: warning: unused variable 'rq' [-Wunused-variable]
Signed-off-by: Kamalesh Babulal <kamalesh@linux.vnet.ibm.com>
Acked-by: Frederic Weisbecker <fweisbec@gmail.com>
Acked-by: Paul Turner <pjt@google.com>
Cc: peterz@infradead.org
Link: http://lkml.kernel.org/r/1369904660-14169-1-git-send-email-kamalesh@linux.vnet.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
In tick_nohz_cpu_down_callback() if the cpu is the one handling
timekeeping, we must return something that stops the CPU_DOWN_PREPARE
notifiers and then start notify CPU_DOWN_FAILED on the already called
notifier call backs.
However traditional errno values are not handled by the notifier unless
these are encapsulated using errno_to_notifier().
Hence the current -EINVAL is misinterpreted and converted to junk after
notifier_to_errno(), leaving the notifier subsystem to random behaviour
such as eventually allowing the cpu to go down.
Fix this by using the standard NOTIFY_BAD instead.
Signed-off-by: Li Zhong <zhong@linux.vnet.ibm.com>
Reviewed-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The kvm_host.h header file doesn't handle well
inclusion when archs don't support KVM.
This results in build crashes for such archs when they
want to implement context tracking because this subsystem
includes kvm_host.h in order to implement the
guest_enter/exit APIs but it doesn't handle KVM off case.
To fix this, move the guest_enter()/guest_exit()
declarations and generic implementation to the context
tracking headers. These generic APIs actually belong to
this subsystem, besides other domains boundary tracking
like user_enter() et al.
KVM now properly becomes a user of this library, not the
other buggy way around.
Reported-by: Kevin Hilman <khilman@linaro.org>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Kevin Hilman <khilman@linaro.org>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Cc: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
While computing the cputime delta of dynticks CPUs,
we are mixing up clocks of differents natures:
* local_clock() which takes care of unstable clock
sources and fix these if needed.
* sched_clock() which is the weaker version of
local_clock(). It doesn't compute any fixup in case
of unstable source.
If the clock source is stable, those two clocks are the
same and we can safely compute the difference against
two random points.
Otherwise it results in random deltas as sched_clock()
can randomly drift away, back or forward, from local_clock().
As a consequence, some strange behaviour with unstable tsc
has been observed such as non progressing constant zero cputime.
(The 'top' command showing no load).
Fix this by only using local_clock(), or its irq safe/remote
equivalent, in vtime code.
Reported-by: Mike Galbraith <efault@gmx.de>
Suggested-by: Mike Galbraith <efault@gmx.de>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Li Zhong <zhong@linux.vnet.ibm.com>
Cc: Mike Galbraith <efault@gmx.de>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull x86 fixes from Peter Anvin:
- Three EFI-related fixes
- Two early memory initialization fixes
- build fix for older binutils
- fix for an eager FPU performance regression -- currently we don't
allow the use of the FPU at interrupt time *at all* in eager mode,
which is clearly wrong.
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86: Allow FPU to be used at interrupt time even with eagerfpu
x86, crc32-pclmul: Fix build with older binutils
x86-64, init: Fix a possible wraparound bug in switchover in head_64.S
x86, range: fix missing merge during add range
x86, efi: initial the local variable of DataSize to zero
efivar: fix oops in efivar_update_sysfs_entries() caused by memory reuse
efivarfs: Never return ENOENT from firmware again
The branch selftest calls trace_test_buffer(), but with the new code
it expects the first parameter to be a pointer to a struct trace_buffer.
All self tests were changed but the branch selftest was missed.
This caused either a crash or failed test when the branch selftest was
enabled.
Link: http://lkml.kernel.org/r/20130529141333.GA24064@localhost
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Below is a patch from android kernel that maintains a histogram of
suspend times. Please review and provide feedback.
Statistices on the time spent in suspend are kept in
/sys/kernel/debug/sleep_time.
Cc: Android Kernel Team <kernel-team@android.com>
Cc: Colin Cross <ccross@android.com>
Cc: Todd Poynor <toddpoynor@google.com>
Cc: San Mehat <san@google.com>
Cc: Benoit Goby <benoit@android.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Colin Cross <ccross@android.com>
Signed-off-by: Todd Poynor <toddpoynor@google.com>
[zoran.markovic@linaro.org: Re-formatted suspend time table to better
fit expected values. Moved accounting of suspend time into timekeeping
core. Removed CONFIG_SUSPEND_TIME flag and made the feature conditional
on CONFIG_DEBUG_FS. Changed the file name to sleep_time to better fit
terminology in timekeeping core. Changed seq_printf to seq_puts. Tweaked
commit message]
Signed-off-by: Zoran Markovic <zoran.markovic@linaro.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Add functions needed for hooking up alarmtimer to timerfd:
* alarm_restart: Similar to hrtimer_restart, restart an alarmtimer after
the expires time has already been updated (as with alarm_forward).
* alarm_forward_now: Similar to hrtimer_forward_now, move the expires
time forward to an interval from the current time of the associated clock.
* alarm_start_relative: Start an alarmtimer with an expires time relative to
the current time of the associated clock.
* alarm_expires_remaining: Similar to hrtimer_expires_remaining, return the
amount of time remaining until alarm expiry.
Signed-off-by: Todd Poynor <toddpoynor@google.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Some controllers have irqs that aren't wired up and must never be used.
For the generic chip attached to an irq_domain this provides a mask that
can be used to block out particular irqs so that they never get mapped.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Link: http://lkml.kernel.org/r/1369793454-19197-2-git-send-email-grant.likely@linaro.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Provide infrastructure for irq chip implementations which work on
linear irq domains.
- Interface to allocate multiple generic chips which are associated to
the irq domain.
- Interface to get the generic chip pointer for a particular hardware
interrupt in the domain.
- irq domain mapping function to install the chip for a particular
interrupt.
Note: This lacks a removal function for now.
[ Sebastian Hesselbarth: Mask cache and pointer math fixups ]
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Russell King - ARM Linux <linux@arm.linux.org.uk>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Jean-Francois Moine <moinejf@free.fr>
Cc: devicetree-discuss@lists.ozlabs.org
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Cc: Gregory Clement <gregory.clement@free-electrons.com>
Cc: Gerlando Falauto <gerlando.falauto@keymile.com>
Cc: Rob Landley <rob@landley.net>
Acked-by: Grant Likely <grant.likely@linaro.org>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Link: http://lkml.kernel.org/r/20130506142539.450634298@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Preparatory patch for linear interrupt domains.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Russell King - ARM Linux <linux@arm.linux.org.uk>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Jean-Francois Moine <moinejf@free.fr>
Cc: devicetree-discuss@lists.ozlabs.org
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Cc: Gregory Clement <gregory.clement@free-electrons.com>
Cc: Gerlando Falauto <gerlando.falauto@keymile.com>
Cc: Rob Landley <rob@landley.net>
Acked-by: Grant Likely <grant.likely@linaro.org>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Link: http://lkml.kernel.org/r/20130506142539.377017672@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Some chips have weird bit mask access patterns instead of the linear
you expect. Allow them to calculate the cached mask themself.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Russell King - ARM Linux <linux@arm.linux.org.uk>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Jean-Francois Moine <moinejf@free.fr>
Cc: devicetree-discuss@lists.ozlabs.org
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Cc: Gregory Clement <gregory.clement@free-electrons.com>
Cc: Gerlando Falauto <gerlando.falauto@keymile.com>
Cc: Rob Landley <rob@landley.net>
Acked-by: Grant Likely <grant.likely@linaro.org>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Link: http://lkml.kernel.org/r/20130506142539.302898834@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cache the per irq bit mask instead of recalculating it over and over.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Russell King - ARM Linux <linux@arm.linux.org.uk>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Jean-Francois Moine <moinejf@free.fr>
Cc: devicetree-discuss@lists.ozlabs.org
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Cc: Gregory Clement <gregory.clement@free-electrons.com>
Cc: Gerlando Falauto <gerlando.falauto@keymile.com>
Cc: Rob Landley <rob@landley.net>
Acked-by: Grant Likely <grant.likely@linaro.org>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Link: http://lkml.kernel.org/r/20130506142539.227119865@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
There are cases where all irq_chip_type instances have separate mask
registers, making a shared mask register cache unsuitable for the
purpose.
Introduce a new flag IRQ_GC_MASK_CACHE_PER_TYPE. If set, point the per
chip mask pointer to the per chip private mask cache instead.
[ tglx: Simplified code, renamed flag and massaged changelog ]
Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Joey Oravec <joravec@drewtech.com>
Cc: Lennert Buytenhek <kernel@wantstofly.org>
Cc: Russell King - ARM Linux <linux@arm.linux.org.uk>
Cc: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Cc: Holger Brunck <Holger.Brunck@keymile.com>
Cc: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Grant Likely <grant.likely@linaro.org>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: devicetree-discuss@lists.ozlabs.org
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Gregory Clement <gregory.clement@free-electrons.com>
Cc: Simon Guinot <simon@sequanux.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Jean-Francois Moine <moinejf@free.fr>
Cc: Nicolas Pitre <nico@fluxnic.net>
Cc: Rob Landley <rob@landley.net>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Link: http://lkml.kernel.org/r/20130506142539.152569748@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Today the same interrupt mask cache (stored within struct irq_chip_generic)
is shared between all the irq_chip_type instances. As there are instances
where each irq_chip_type uses a distinct mask register (as it is the case
for Orion SoCs), sharing a single mask cache may be incorrect.
So add a distinct pointer for each irq_chip_type, which for now
points to the original mask register within irq_chip_generic.
So no functional changes here.
[ tglx: Minor cosmetic tweaks ]
Reported-by: Joey Oravec <joravec@drewtech.com>
Signed-off-by: Simon Guinot <sguinot@lacie.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Lennert Buytenhek <kernel@wantstofly.org>
Cc: Russell King - ARM Linux <linux@arm.linux.org.uk>
Cc: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Cc: Holger Brunck <Holger.Brunck@keymile.com>
Cc: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Grant Likely <grant.likely@linaro.org>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: devicetree-discuss@lists.ozlabs.org
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Gregory Clement <gregory.clement@free-electrons.com>
Cc: Simon Guinot <simon@sequanux.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Jean-Francois Moine <moinejf@free.fr>
Cc: Nicolas Pitre <nico@fluxnic.net>
Cc: Rob Landley <rob@landley.net>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Link: http://lkml.kernel.org/r/20130506142539.082226607@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Since we already have an irq_data_get_chip_type() function which returns
a pointer to irq_chip_type, use that instead of cur_regs().
Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Joey Oravec <joravec@drewtech.com>
Cc: Lennert Buytenhek <kernel@wantstofly.org>
Cc: Russell King - ARM Linux <linux@arm.linux.org.uk>
Cc: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Cc: Holger Brunck <Holger.Brunck@keymile.com>
Cc: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Grant Likely <grant.likely@linaro.org>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: devicetree-discuss@lists.ozlabs.org
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Gregory Clement <gregory.clement@free-electrons.com>
Cc: Simon Guinot <simon@sequanux.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Jean-Francois Moine <moinejf@free.fr>
Cc: Nicolas Pitre <nico@fluxnic.net>
Cc: Rob Landley <rob@landley.net>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Link: http://lkml.kernel.org/r/20130506142539.010164766@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
As rcu_dereference_raw() under RCU debug config options can add quite a
bit of checks, and that tracing uses rcu_dereference_raw(), these checks
happen with the function tracer. The function tracer also happens to trace
these debug checks too. This added overhead can livelock the system.
Have the function tracer use the new RCU _notrace equivalents that do
not do the debug checks for RCU.
Link: http://lkml.kernel.org/r/20130528184209.467603904@goodmis.org
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
With the new __DEVEL__sane_behavior mount option was introduced,
if the root cgroup is alive with no xattr function, to mount a
new cgroup with xattr will be rejected in terms of design which
just fine. However, if the root cgroup does not mounted with
__DEVEL__sane_hehavior, to create a new cgroup with xattr option
will succeed although after that the EA function does not works
as expected but will get ENOTSUPP for setting up attributes under
either cgroup. e.g.
setfattr: /cgroup2/test: Operation not supported
Instead of keeping silence in this case, it's better to drop a log
entry in warning level. That would be helpful to understand the
reason behind the scene from the user's perspective, and this is
essentially an improvement does not break the backward compatibilities.
With this fix, above mount attemption will keep up works as usual but
the following line cound be found at the system log:
[ ...] cgroup: new mount options do not match the existing superblock
tj: minor formatting / message updates.
Signed-off-by: Jie Liu <jeff.liu@oracle.com>
Reported-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
Since commit 31ade30692, timekeeping_init()
checks for presence of persistent clock by attempting to read a non-zero
time value. This is an issue on platforms where persistent_clock (instead
is implemented as a free-running counter (instead of an RTC) starting
from zero on each boot and running during suspend. Examples are some ARM
platforms (e.g. PandaBoard).
An attempt to read such a clock during timekeeping_init() may return zero
value and falsely declare persistent clock as missing. Additionally, in
the above case suspend times may be accounted twice (once from
timekeeping_resume() and once from rtc_resume()), resulting in a gradual
drift of system time.
This patch does a run-time correction of the issue by doing the same check
during timekeeping_suspend().
A better long-term solution would have to return error when trying to read
non-existing clock and zero when trying to read an uninitialized clock, but
that would require changing all persistent_clock implementations.
This patch addresses the immediate breakage, for now.
Cc: John Stultz <john.stultz@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Feng Tang <feng.tang@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Zoran Markovic <zoran.markovic@linaro.org>
[jstultz: Tweaked commit message and subject]
Signed-off-by: John Stultz <john.stultz@linaro.org>
kernel/time/ntp.c: In function ‘__hardpps’:
kernel/time/ntp.c:877: warning: unused variable ‘flags’
commit a076b2146f ("ntp: Remove ntp_lock,
using the timekeeping locks to protect ntp state") removed its users,
but not the actual variable.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
The first one was reported by Mauro Carvalho Chehab, where if a poll()
is done against a trace buffer for a CPU that has never been online,
it will crash the kernel, as buffers are only created when a CPU comes
on line, but the trace files are for all possible CPUs.
This fix is to check if the buffer was allocated and if not return -EINVAL.
That was the simple fix, the real fix is a bit more complex and not for
a -rc release. We could have the files created when the CPUs come online.
That would require some design changes.
The second one was reported by Peter Zijlstra. If the kernel command line
has ftrace=nop, it will lock up the system on boot up. This is because
the new design for 3.10 has the nop tracer bootstrap the tracing subsystem.
When ftrace=<trace> is defined, when a that tracer is registered, it
starts the tracing, but uses the nop tracer to clear things out.
What happened here was that ftrace=nop caused the registering of nop
to start it and use nop before it was initialized.
The only thing nop needs to have done to initialize it is to have the
tracer point its current_tracer structure member to the nop tracer.
Doing that before registering the nop tracer makes everything work.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJRpMkPAAoJEOdOSU1xswtMxeEIALWCnqSCKZJ0Oz+2TuR15vd2
Szm/knRBktRG2FizN8FIouXXMLIYM5HFSvO3Q2bWuV4Dv5KaqNcCEL5BggZC/+Rj
swt5+rMiUuln0teq792h2LhKwORw0YicLzWsyIZ82iSpcFKAseXqcMzEe/P/Emat
+J1QaoeDtOx/3X5Sv6tqHomqR80u7phQJwmIK6Yik389yLo3sy2XiPRk9PJqDpac
V9xbCnZlnopm7rLo7pEAI3R6Vn+MX6lrY1MO0xxjqeIvhvxr9nk0WIRnaevyARbt
eHnCtfa9pjn+bU9xYaFmyIkilc/IEBFRLb0dtEueH81nmaFDXpHI+h/pEFrDJqE=
=PR0j
-----END PGP SIGNATURE-----
Merge tag 'trace-fixes-v3.10-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fixes from Steven Rostedt:
"Two more fixes:
The first one was reported by Mauro Carvalho Chehab, where if a poll()
is done against a trace buffer for a CPU that has never been online,
it will crash the kernel, as buffers are only created when a CPU comes
on line, but the trace files are for all possible CPUs.
This fix is to check if the buffer was allocated and if not return
-EINVAL.
That was the simple fix, the real fix is a bit more complex and not
for a -rc release. We could have the files created when the CPUs come
online. That would require some design changes.
The second one was reported by Peter Zijlstra. If the kernel command
line has ftrace=nop, it will lock up the system on boot up. This is
because the new design for 3.10 has the nop tracer bootstrap the
tracing subsystem. When ftrace=<trace> is defined, when a that tracer
is registered, it starts the tracing, but uses the nop tracer to clear
things out. What happened here was that ftrace=nop caused the
registering of nop to start it and use nop before it was initialized.
The only thing nop needs to have done to initialize it is to have the
tracer point its current_tracer structure member to the nop tracer.
Doing that before registering the nop tracer makes everything work."
* tag 'trace-fixes-v3.10-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
ring-buffer: Do not poll non allocated cpu buffers
tracing: Fix crash when ftrace=nop on the kernel command line
The tracing infrastructure sets up for possible CPUs, but it uses
the ring buffer polling, it is possible to call the ring buffer
polling code with a CPU that hasn't been allocated. This will cause
a kernel oops when it access a ring buffer cpu buffer that is part
of the possible cpus but hasn't been allocated yet as the CPU has never
been online.
Reported-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Tested-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
In old kernels, it's allowed to set softlockup_thresh to -1 or 0
to disable softlockup detection. However watchdog_thresh only
uses 0 to disable detection, and setting it to -1 just froze my
box and nothing I can do but reboot.
Signed-off-by: Li Zefan <lizefan@huawei.com>
Acked-by: Don Zickus <dzickus@redhat.com>
Link: http://lkml.kernel.org/r/51959668.9040106@huawei.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Vince reported a problem found by his perf specific trinity
fuzzer.
Al noticed 2 problems with perf's mmap():
- it has issues against fork() since we use vma->vm_mm for accounting.
- it has an rb refcount leak on double mmap().
We fix the issues against fork() by using VM_DONTCOPY; I don't
think there's code out there that uses this; we didn't hear
about weird accounting problems/crashes. If we do need this to
work, the previously proposed VM_PINNED could make this work.
Aside from the rb reference leak spotted by Al, Vince's example
prog was indeed doing a double mmap() through the use of
perf_event_set_output().
This exposes another problem, since we now have 2 events with
one buffer, the accounting gets screwy because we account per
event. Fix this by making the buffer responsible for its own
accounting.
Reported-by: Vince Weaver <vincent.weaver@maine.edu>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Link: http://lkml.kernel.org/r/20130528085548.GA12193@twins.programming.kicks-ass.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Fix to free gone and unused optprobes. This bug will
cause a kernel panic if the user reuses the killed and
unused probe.
Reported at:
http://sourceware.org/ml/systemtap/2013-q2/msg00142.html
In the normal path, an optprobe on an init function is
unregistered when a module goes live.
unregister_kprobe(kp)
-> __unregister_kprobe_top
->__disable_kprobe
->disarm_kprobe(ap == op)
->__disarm_kprobe
->unoptimize_kprobe : the op is queued
on unoptimizing_list
and do nothing in __unregister_kprobe_bottom
After a while (usually wait 5 jiffies), kprobe_optimizer
runs to unoptimize and free optprobe.
kprobe_optimizer
->do_unoptimize_kprobes
->arch_unoptimize_kprobes : moved to free_list
->do_free_cleaned_kprobes
->hlist_del: the op is removed
->free_aggr_kprobe
->arch_remove_optimized_kprobe
->arch_remove_kprobe
->kfree: the op is freed
Here, if kprobes_module_callback is called and the delayed
unoptimizing probe is picked BEFORE kprobe_optimizer runs,
kprobes_module_callback
->kill_kprobe
->kill_optimized_kprobe : dequeued from unoptimizing_list <=!!!
->arch_remove_optimized_kprobe
->arch_remove_kprobe
(but op is not freed, and on the kprobe hash table)
This doesn't happen if the probe unregistration is done AFTER
kprobes_module_callback is called (because at that time the op
is gone), and kprobe-tracer does it.
To fix this bug, this patch changes kprobes_module_callback to
enqueue the op to freeing_list at kill_optimized_kprobe only
if the op is unused. The unused probes on freeing_list will
be freed in do_free_cleaned_kprobes.
Note that this calls arch_remove_*kprobe twice on the
same probe. Thus those functions have to check the double free.
Fortunately, most of arch codes already checked that except
for mips. This will be fixed in the next patch.
Signed-off-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Timo Juhani Lindfors <timo.lindfors@iki.fi>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Cc: Frank Ch. Eigler <fche@redhat.com>
Cc: systemtap@sourceware.org
Cc: yrl.pp-manager.tt@hitachi.com
Cc: David S. Miller <davem@davemloft.net>
Cc: "David S. Miller" <davem@davemloft.net>
Link: http://lkml.kernel.org/r/20130522093409.9084.63554.stgit@mhiramat-M0-7522
[ Minor edits. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
commit 7eaeb34305 (clocksource: Provide unbind interface in sysfs)
implemented clocksource_select_fallback() which is not defined for
CONFIG_ARCH_USES_GETTIMEOFFSET=y. Add an empty inline function for
that.
Reported-by: Ingo Molnar <mingo@kernel.org>
Reported-by: fengguang.wu@intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Read the runqueue clock through an accessor. This
prepares for adding a debugging infrastructure to
detect missing or redundant calls to update_rq_clock()
between a scheduler's entry and exit point.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Li Zhong <zhong@linux.vnet.ibm.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Paul Turner <pjt@google.com>
Cc: Mike Galbraith <efault@gmx.de>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1365724262-20142-6-git-send-email-fweisbec@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Linus Torvalds
Rafael J. Wysocki
David Vrabel
Bart Van Assche
Davidlohr Bueso
Alex Shi
Thomas Gleixner
Fabio Estevam
Ben Hutchings
Kamalesh Babulal
Tejun Heo
Shuah Khan
Daniel Vetter
Maarten Lankhorst
JunweiZhang
Ingo Molnar
Colin Cross
Zhang Yi
Javier Martinez Canillas
Greg Kroah-Hartman
Stephen Boyd
James Hogan
Kefeng Wang
Grant Likely
Grant Likely
Sahara
Dave Hansen
Daniel Lezcano
Julius Werner
Oleg Nesterov
Frederic Weisbecker
Juri Lelli
zhangwei(Jovi)
Steven Rostedt (Red Hat)
Joe Perches
Viresh Kumar
Michael Wang
Kirill Tkhai
Vincent Guittot
Mischa Jonker
Stephane Eranian
Peter Zijlstra
Li Zefan
Yinghai Lu
Uwe Kleine-König
James Bottomley
Chen Gang
Kees Cook
Robin Holt
Srivatsa S. Bhat
Marcus Gelderie
Namhyung Kim
Wang YanQing
Harsh Prateek Bora
Bernie Thompson
Yoshihiro YUNOMAE
Ivo Sieben
Ben Greear
Paul E. McKenney
Linus Walleij
Arnd Bergmann
Chen Gong
Stephen Rothwell
Bjorn Helgaas
Jiri Bohac
Li Zhong
Todd Poynor
Andreas Fenkart
Gerlando Falauto
Jeff Liu
Zoran Markovic
Geert Uytterhoeven
Stanislaw Gruszka
Masami Hiramatsu