The error handling in prepare_output has several issues with
resource leaks. Ensure that filename is free'd and the directory
stream DIR is closed before returning.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Thomas Renninger <trenn@suse.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Mattia Dongili <malattia@linux.it>
Signed-off-by: Thomas Renninger <trenn@suse.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The logic on the test for a valid fd to close is incorrect.
This was just a mistake and was pointed out by Colin Ian King.
Link: https://patchwork.kernel.org/patch/8620201/
Original-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* pm-core:
PM / wakeirq: fix wakeirq setting after wakup re-configuration from sysfs
PM / runtime: Document steps for device removal
* powercap:
powercap: intel_rapl: Add missing Haswell model
* pm-tools:
tools/power turbostat: work around RC6 counter wrap
tools/power turbostat: initial KBL support
tools/power turbostat: initial SKX support
tools/power turbostat: decode BXT TSC frequency via CPUID
tools/power turbostat: initial BXT support
tools/power turbostat: print IRTL MSRs
tools/power turbostat: SGX state should print only if --debug
Sometimes the rc6 sysfs counter spontaneously resets,
causing turbostat prints a very large number
as it tries to calcuate % = 100 * (old - new) / interval
When we see (old > new), print ***.**% instead
of a bogus huge number.
Note that this detection is not fool-proof, as the counter
could reset several times and still result in new > old.
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Hard-code BXT ART to 19200MHz, so turbostat --debug
can fully enumerate TSC:
CPUID(0x15): eax_crystal: 3 ebx_tsc: 186 ecx_crystal_hz: 0
TSC: 1190 MHz (19200000 Hz * 186 / 3 / 1000000)
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Some processors use the Interrupt Response Time Limit (IRTL) MSR value
to describe the maximum IRQ response time latency for deep
package C-states. (Though others have the register, but do not use it)
Lets print it out to give insight into the cases where it is used.
IRTL begain in SNB, with PC3/PC6/PC7, and HSW added PC8/PC9/PC10.
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The CPUID.SGX bit was printed, even if --debug was used
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 795e136d2ac77c1c8b091fba019b5fe36a44a323
Fixes a problem with the merger of the two internal versions
of this function. Make the maximum integer width (32-bit or
64-bit) a parameter to the function so that it no longer
exclusively uses the integer width specified in the DSDT/SSDT.
ACPICA BZ 1260
Link: https://github.com/acpica/acpica/commit/795e136d
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 37a1dec2391272251e59948c16c60713183ae78f
Link: https://github.com/acpica/acpica/commit/37a1dec2
Signed-off-by: Will Miles <wmiles@sgl.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
- Redesign of cpufreq governors and the intel_pstate driver to
make them use callbacks invoked by the scheduler to trigger CPU
frequency evaluation instead of using per-CPU deferrable timers
for that purpose (Rafael Wysocki).
- Reorganization and cleanup of cpufreq governor code to make it
more straightforward and fix some concurrency problems in it
(Rafael Wysocki, Viresh Kumar).
- Cleanup and improvements of locking in the cpufreq core (Viresh
Kumar).
- Assorted cleanups in the cpufreq core (Rafael Wysocki, Viresh
Kumar, Eric Biggers).
- intel_pstate driver updates including fixes, optimizations and a
modification to make it enable enable hardware-coordinated P-state
selection (HWP) by default if supported by the processor (Philippe
Longepe, Srinivas Pandruvada, Rafael Wysocki, Viresh Kumar, Felipe
Franciosi).
- Operating Performance Points (OPP) framework updates to improve
its handling of voltage regulators and device clocks and updates
of the cpufreq-dt driver on top of that (Viresh Kumar, Jon Hunter).
- Updates of the powernv cpufreq driver to fix initialization
and cleanup problems in it and correct its worker thread handling
with respect to CPU offline, new powernv_throttle tracepoint
(Shilpasri Bhat).
- ACPI cpufreq driver optimization and cleanup (Rafael Wysocki).
- ACPICA updates including one fix for a regression introduced
by previos changes in the ACPICA code (Bob Moore, Lv Zheng,
David Box, Colin Ian King).
- Support for installing ACPI tables from initrd (Lv Zheng).
- Optimizations of the ACPI CPPC code (Prashanth Prakash, Ashwin
Chaugule).
- Support for _HID(ACPI0010) devices (ACPI processor containers)
and ACPI processor driver cleanups (Sudeep Holla).
- Support for ACPI-based enumeration of the AMBA bus (Graeme Gregory,
Aleksey Makarov).
- Modification of the ACPI PCI IRQ management code to make it treat
255 in the Interrupt Line register as "not connected" on x86 (as
per the specification) and avoid attempts to use that value as
a valid interrupt vector (Chen Fan).
- ACPI APEI fixes related to resource leaks (Josh Hunt).
- Removal of modularity from a few ACPI drivers (BGRT, GHES,
intel_pmic_crc) that cannot be built as modules in practice (Paul
Gortmaker).
- PNP framework update to make it treat ACPI_RESOURCE_TYPE_SERIAL_BUS
as a valid resource type (Harb Abdulhamid).
- New device ID (future AMD I2C controller) in the ACPI driver for
AMD SoCs (APD) and in the designware I2C driver (Xiangliang Yu).
- Assorted ACPI cleanups (Colin Ian King, Kaiyen Chang, Oleg Drokin).
- cpuidle menu governor optimization to avoid a square root
computation in it (Rasmus Villemoes).
- Fix for potential use-after-free in the generic device properties
framework (Heikki Krogerus).
- Updates of the generic power domains (genpd) framework including
support for multiple power states of a domain, fixes and debugfs
output improvements (Axel Haslam, Jon Hunter, Laurent Pinchart,
Geert Uytterhoeven).
- Intel RAPL power capping driver updates to reduce IPI overhead in
it (Jacob Pan).
- System suspend/hibernation code cleanups (Eric Biggers, Saurabh
Sengar).
- Year 2038 fix for the process freezer (Abhilash Jindal).
- turbostat utility updates including new features (decoding of more
registers and CPUID fields, sub-second intervals support, GFX MHz
and RC6 printout, --out command line option), fixes (syscall jitter
detection and workaround, reductioin of the number of syscalls made,
fixes related to Xeon x200 processors, compiler warning fixes) and
cleanups (Len Brown, Hubert Chrzaniuk, Chen Yu).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=cfty
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-4.6-rc1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI updates from Rafael Wysocki:
"This time the majority of changes go into cpufreq and they are
significant.
First off, the way CPU frequency updates are triggered is different
now. Instead of having to set up and manage a deferrable timer for
each CPU in the system to evaluate and possibly change its frequency
periodically, cpufreq governors set up callbacks to be invoked by the
scheduler on a regular basis (basically on utilization updates). The
"old" governors, "ondemand" and "conservative", still do all of their
work in process context (although that is triggered by the scheduler
now), but intel_pstate does it all in the callback invoked by the
scheduler with no need for any additional asynchronous processing.
Of course, this eliminates the overhead related to the management of
all those timers, but also it allows the cpufreq governor code to be
simplified quite a bit. On top of that, the common code and data
structures used by the "ondemand" and "conservative" governors are
cleaned up and made more straightforward and some long-standing and
quite annoying problems are addressed. In particular, the handling of
governor sysfs attributes is modified and the related locking becomes
more fine grained which allows some concurrency problems to be avoided
(particularly deadlocks with the core cpufreq code).
In principle, the new mechanism for triggering frequency updates
allows utilization information to be passed from the scheduler to
cpufreq. Although the current code doesn't make use of it, in the
works is a new cpufreq governor that will make decisions based on the
scheduler's utilization data. That should allow the scheduler and
cpufreq to work more closely together in the long run.
In addition to the core and governor changes, cpufreq drivers are
updated too. Fixes and optimizations go into intel_pstate, the
cpufreq-dt driver is updated on top of some modification in the
Operating Performance Points (OPP) framework and there are fixes and
other updates in the powernv cpufreq driver.
Apart from the cpufreq updates there is some new ACPICA material,
including a fix for a problem introduced by previous ACPICA updates,
and some less significant changes in the ACPI code, like CPPC code
optimizations, ACPI processor driver cleanups and support for loading
ACPI tables from initrd.
Also updated are the generic power domains framework, the Intel RAPL
power capping driver and the turbostat utility and we have a bunch of
traditional assorted fixes and cleanups.
Specifics:
- Redesign of cpufreq governors and the intel_pstate driver to make
them use callbacks invoked by the scheduler to trigger CPU
frequency evaluation instead of using per-CPU deferrable timers for
that purpose (Rafael Wysocki).
- Reorganization and cleanup of cpufreq governor code to make it more
straightforward and fix some concurrency problems in it (Rafael
Wysocki, Viresh Kumar).
- Cleanup and improvements of locking in the cpufreq core (Viresh
Kumar).
- Assorted cleanups in the cpufreq core (Rafael Wysocki, Viresh
Kumar, Eric Biggers).
- intel_pstate driver updates including fixes, optimizations and a
modification to make it enable enable hardware-coordinated P-state
selection (HWP) by default if supported by the processor (Philippe
Longepe, Srinivas Pandruvada, Rafael Wysocki, Viresh Kumar, Felipe
Franciosi).
- Operating Performance Points (OPP) framework updates to improve its
handling of voltage regulators and device clocks and updates of the
cpufreq-dt driver on top of that (Viresh Kumar, Jon Hunter).
- Updates of the powernv cpufreq driver to fix initialization and
cleanup problems in it and correct its worker thread handling with
respect to CPU offline, new powernv_throttle tracepoint (Shilpasri
Bhat).
- ACPI cpufreq driver optimization and cleanup (Rafael Wysocki).
- ACPICA updates including one fix for a regression introduced by
previos changes in the ACPICA code (Bob Moore, Lv Zheng, David Box,
Colin Ian King).
- Support for installing ACPI tables from initrd (Lv Zheng).
- Optimizations of the ACPI CPPC code (Prashanth Prakash, Ashwin
Chaugule).
- Support for _HID(ACPI0010) devices (ACPI processor containers) and
ACPI processor driver cleanups (Sudeep Holla).
- Support for ACPI-based enumeration of the AMBA bus (Graeme Gregory,
Aleksey Makarov).
- Modification of the ACPI PCI IRQ management code to make it treat
255 in the Interrupt Line register as "not connected" on x86 (as
per the specification) and avoid attempts to use that value as a
valid interrupt vector (Chen Fan).
- ACPI APEI fixes related to resource leaks (Josh Hunt).
- Removal of modularity from a few ACPI drivers (BGRT, GHES,
intel_pmic_crc) that cannot be built as modules in practice (Paul
Gortmaker).
- PNP framework update to make it treat ACPI_RESOURCE_TYPE_SERIAL_BUS
as a valid resource type (Harb Abdulhamid).
- New device ID (future AMD I2C controller) in the ACPI driver for
AMD SoCs (APD) and in the designware I2C driver (Xiangliang Yu).
- Assorted ACPI cleanups (Colin Ian King, Kaiyen Chang, Oleg Drokin).
- cpuidle menu governor optimization to avoid a square root
computation in it (Rasmus Villemoes).
- Fix for potential use-after-free in the generic device properties
framework (Heikki Krogerus).
- Updates of the generic power domains (genpd) framework including
support for multiple power states of a domain, fixes and debugfs
output improvements (Axel Haslam, Jon Hunter, Laurent Pinchart,
Geert Uytterhoeven).
- Intel RAPL power capping driver updates to reduce IPI overhead in
it (Jacob Pan).
- System suspend/hibernation code cleanups (Eric Biggers, Saurabh
Sengar).
- Year 2038 fix for the process freezer (Abhilash Jindal).
- turbostat utility updates including new features (decoding of more
registers and CPUID fields, sub-second intervals support, GFX MHz
and RC6 printout, --out command line option), fixes (syscall jitter
detection and workaround, reductioin of the number of syscalls
made, fixes related to Xeon x200 processors, compiler warning
fixes) and cleanups (Len Brown, Hubert Chrzaniuk, Chen Yu)"
* tag 'pm+acpi-4.6-rc1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (182 commits)
tools/power turbostat: bugfix: TDP MSRs print bits fixing
tools/power turbostat: correct output for MSR_NHM_SNB_PKG_CST_CFG_CTL dump
tools/power turbostat: call __cpuid() instead of __get_cpuid()
tools/power turbostat: indicate SMX and SGX support
tools/power turbostat: detect and work around syscall jitter
tools/power turbostat: show GFX%rc6
tools/power turbostat: show GFXMHz
tools/power turbostat: show IRQs per CPU
tools/power turbostat: make fewer systems calls
tools/power turbostat: fix compiler warnings
tools/power turbostat: add --out option for saving output in a file
tools/power turbostat: re-name "%Busy" field to "Busy%"
tools/power turbostat: Intel Xeon x200: fix turbo-ratio decoding
tools/power turbostat: Intel Xeon x200: fix erroneous bclk value
tools/power turbostat: allow sub-sec intervals
ACPI / APEI: ERST: Fixed leaked resources in erst_init
ACPI / APEI: Fix leaked resources
intel_pstate: Do not skip samples partially
intel_pstate: Remove freq calculation from intel_pstate_calc_busy()
intel_pstate: Move intel_pstate_calc_busy() into get_target_pstate_use_performance()
...
Pull turbostat updates for 4.6 from Len Brown.
* 'turbostat' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
tools/power turbostat: bugfix: TDP MSRs print bits fixing
tools/power turbostat: correct output for MSR_NHM_SNB_PKG_CST_CFG_CTL dump
tools/power turbostat: call __cpuid() instead of __get_cpuid()
tools/power turbostat: indicate SMX and SGX support
tools/power turbostat: detect and work around syscall jitter
tools/power turbostat: show GFX%rc6
tools/power turbostat: show GFXMHz
tools/power turbostat: show IRQs per CPU
tools/power turbostat: make fewer systems calls
tools/power turbostat: fix compiler warnings
tools/power turbostat: add --out option for saving output in a file
tools/power turbostat: re-name "%Busy" field to "Busy%"
tools/power turbostat: Intel Xeon x200: fix turbo-ratio decoding
tools/power turbostat: Intel Xeon x200: fix erroneous bclk value
tools/power turbostat: allow sub-sec intervals
tools/power turbostat: Decode MSR_MISC_PWR_MGMT
tools/power turbostat: decode HWP registers
x86 msr-index: Simplify syntax for HWP fields
tools/power turbostat: CPUID(0x16) leaf shows base, max, and bus frequency
tools/power turbostat: decode more CPUID fields
MSR_CONFIG_TDP_NOMINAL:
should print all 8 bits of base_ratio (bit 0:7) 0xFF
MSR_CONFIG_TDP_LEVEL_1:
should print all 15 bits of PKG_MIN_PWR_LVL1 (bit 48:62) 0x7FFF
should print all 15 bits of PKG_MAX_PWR_LVL1 (bit 32:46) 0x7FFF
should print all 8 bits of LVL1_RATIO (bit 16:23) 0xFF
should print all 15 bits of PKG_TDP_LVL1 (bit 0:14) 0x7FFF
And the same modification to MSR_CONFIG_TDP_LEVEL_2.
MSR_TURBO_ACTIVATION_RATIO:
should print all 8 bits of MAX_NON_TURBO_RATIO (bit 0:7) 0xFF
Signed-off-by: Chen Yu <yu.c.chen@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
MSR_NHM_SNB_PKG_CST_CFG_CTL: 0x1e008008 (...pkg-cstate-limit=0: unlimited)
should print as
MSR_NHM_SNB_PKG_CST_CFG_CTL: 0x1e008008 (...pkg-cstate-limit=8: unlimited)
Signed-off-by: Len Brown <len.brown@intel.com>
turbostat already checks whether calling each cpuid leavf is legal,
and it doesn't look at the function return value,
so call the simpler gcc intrinsic __cpuid() instead of __get_cpuid().
syntax only, no functional change
Signed-off-by: Len Brown <len.brown@intel.com>
The accuracy of Bzy_Mhz and Busy% depend on reading
the TSC, APERF, and MPERF close together in time.
When there is a very short measurement interval,
or a large system is profoundly idle, the changes
in APERF and MPERF may be very small.
They can be small enough that an expensive interrupt
between reading APERF and MPERF can cause the APERF/MPERF
ratio to become inaccurate, resulting in invalid
calculation and display of Bzy_MHz.
A dummy APERF read of APERF makes this problem
much more rare. Apparently this 1st systemn call
after exiting a long stretch of idle is when we
typically see expensive timer interrupts that cause
large jitter.
For the cases that dummy APERF read fails to prevent,
we compare the latency of the APERF and MPERF reads.
If they differ by more than 2x, we re-issue them.
Signed-off-by: Len Brown <len.brown@intel.com>
The column "GFX%c6" show the percentage of time the GPU
is in the "render C6" state, rc6. Deep package C-states on several
systems depend on the GPU being in RC6.
This information comes from the counter
/sys/class/drm/card0/power/rc6_residency_ms,
as read before and after the measurement interval.
Signed-off-by: Len Brown <len.brown@intel.com>
Under the column "GFXMHz", show a snapshot of this attribute:
/sys/class/graphics/fb0/device/drm/card0/gt_cur_freq_mhz
This is an instantaneous snapshot of what sysfs presents
at the end of the measurement interval. turbostat does
not average or otherwise perform any math on this value.
Signed-off-by: Len Brown <len.brown@intel.com>
The new IRQ column shows how many interrupts have occurred on each CPU
during the measurement inteval. This information comes from
the difference between /proc/interrupts shapshots made before
and after the measurement interval.
The first row, the system summary, shows the sum of the IRQS
for all CPUs during that interval.
Signed-off-by: Len Brown <len.brown@intel.com>
skip the open(2)/close(2) on each msr read
by keeping the /dev/cpu/*/msr files open.
The remaining read(2) is generally far fewer cycles
than the removed open(2) system call.
Signed-off-by: Len Brown <len.brown@intel.com>
By default...
Turbostat --debug gconfiguration info goes to stderr.
In FORK mode, turbostat statistics go to stderr.
In PERIODIC mode, turbostat statistics go to stdout.
These defaults do not change, but an option "--out file"
will send all output above only to the specified file.
Signed-off-by: Len Brown <len.brown@intel.com>
some tools processing turbostat output
have difficulty with items that begin with %...
Reported-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Following changes have been made:
- changed MSR_NHM_TURBO_RATIO_LIMIT to MSR_TURBO_RATIO_LIMIT in debug print
for consistency with Developer Manual
- updated definition of bitfields in MSR_TURBO_RATIO_LIMIT and appropriate
parsing code
- added x200 to list of architectures that do not support Nahlem compatible
definition of MSR_TURBO_RATIO_LIMIT register (x200 has the register but
bits definition is custom)
- fixed typo in code that parses MSR_TURBO_RATIO_LIMIT
(logical instead of bitwise operator)
- changed MSR_TURBO_RATIO_LIMIT parsing algorithm so the print out had the
same order as implementations for other platforms
Signed-off-by: Hubert Chrzaniuk <hubert.chrzaniuk@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
x200 does not enable any way to programmatically obtain bus clock
speed. Bclk for the architecture has a fixed value of 100 MHz.
At the same time x200 cannot be included in has_snb_msrs since
it does not support C7 idle state.
prior to this patch, MHz values reported on this chip
were erroneously calculated using bclk of 133MHz,
causing MHz values to be reported 33% higher than actual.
Signed-off-by: Hubert Chrzaniuk <hubert.chrzaniuk@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
turbostat -i interval_sec
will sample and display statistics every interval_sec.
interval_sec used to be a whole number of seconds,
but now we accept a decimal, as small as 0.001 sec (1 ms).
Signed-off-by: Len Brown <len.brown@intel.com>
When building with gcc 6 we're getting various build warnings that just
require some trivial function declaration and call fixes:
turbostat.c: In function ‘dump_cstate_pstate_config_info’:
turbostat.c:1973:1: warning: type of ‘family’ defaults to ‘int’
dump_cstate_pstate_config_info(family, model)
turbostat.c:1973:1: warning: type of ‘model’ defaults to ‘int’
turbostat.c: In function ‘get_tdp’:
turbostat.c:2145:8: warning: type of ‘model’ defaults to ‘int’
double get_tdp(model)
turbostat.c: In function ‘perf_limit_reasons_probe’:
turbostat.c:2259:6: warning: type of ‘family’ defaults to ‘int’
void perf_limit_reasons_probe(family, model)
turbostat.c:2259:6: warning: type of ‘model’ defaults to ‘int’
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Cc: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/n/tip-wbicer8n0s9qe6ql8h9x478e@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
for debugging, dump a few more fields:
CPUID(1): SSE3 MONITOR EIST TM2 TSC MSR ACPI-TM TM
cpu0: MSR_IA32_MISC_ENABLE: 0x00850089 (TCC EIST MONITOR)
Signed-off-by: Len Brown <len.brown@intel.com>
Fix the following build error by including limits.h -
utils/cpufreq-info.c: In function ‘get_latency’:
utils/cpufreq-info.c:437:29: error: ‘UINT_MAX’ undeclared (first use in
this function)
if (!latency || latency == UINT_MAX) {
^
Signed-off-by: Shreyas B. Prabhu <shreyas@linux.vnet.ibm.com>
Fixes: e98f033f94 (cpupower: fix how "cpupower frequency-info" interprets latency)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
All tool/utility signons.
Dual-license module header.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* pm-sleep:
PM / sleep: Add support for read-only sysfs attributes
* pm-tools:
cpupower: fix how "cpupower frequency-info" interprets latency
cpupower: rework the "cpupower frequency-info" command
cpupower: Do not analyse offlined cpus
cpupower: Provide STATIC variable in Makefile for debug builds
cpupower: Fix precedence issue
ACPICA commit 0d784a90bc3aac75227c4459c3553de18b9ebe7a
Document one of the option string operators.
Link: https://github.com/acpica/acpica/commit/0d784a90
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit dfa394471f6c01b2ee9433dbc143ec70cb9bca72
Mostly indentation inconsistencies across the code. Split
some long lines, etc.
Link: https://github.com/acpica/acpica/commit/dfa39447
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch adds a userspace tool to access Linux kernel AML debugger
interface.
Tow modes are supported by this tool:
1. Interactive: Users are able to launch a debugging shell to talk with
in-kernel AML debugger.
Note that it's user duty to ensure kernel runtime integrity by using
this debugging tool:
A. Some control methods evaluated by the users may result in kernel
panics if those control methods shouldn't be evaluated by the OSPMs
according to the current BIOS/OS configurations.
B. Currently if a single stepping evaluation couldn't run to an end,
then the synchronization primitives acquired by the evaluation may
block normal OSPM control method evaluations.
2. Batch: Users are able to execute debugger commands in a script.
Note that in addition to the above duties, it's user duty to ensure
script runtime integrity by using this debugging tool in this mode:
C. Currently only those commands that are not used for single stepping
are suitable to be used in this mode.
D. If the execution of the command may cause a failure that could result
in an endless kernel execution, the execution of the script may also
get blocked.
To exit the utility, currently "exit/quit" commands are recommended, but
ctrl-C" can also be used.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
the intel-pstate driver does not support the ondemand governor and does not
have a valid value in
/sys/devices/system/cpu/cpu[x]/cpufreq/cpuinfo_transition_latency. The
intel-pstate driver sets cpuinfo_transition_latency to CPUFREQ_ETERNAL (-1),
the value written into cpuinfo_transition_latency is defind as an unsigned
int so checking the read value against max unsigned int will determine if the
value is valid.
Signed-off-by: Jacob Tanenbaum <jtanenba@redhat.com>
Signed-off-by: Thomas Renninger <trenn@suse.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
this patch makes two changes to the way that "cpupower
frequancy-info" operates
1. make it so that querying individual values always returns a
message to the user
currently cpupower frequency info doesn't return anything to the user when
querying an individual value cannot be returned
[root@amd-dinar-09 cpupower]# cpupower -c 4 frequency-info -d
analyzing CPU 4:
[root@amd-dinar-09 cpupower]#
I added messages so that each query prints a message to the terminal
[root@amd-dinar-09 cpupower]# ./cpupower -c 4 frequency-info -d
analyzing CPU 4:
no or unknown cpufreq driver is active on this CPU
[root@amd-dinar-09 cpupower]#
(this is just one example)
2. change debug_output_one() to use the functions already provided
by cpufreq-info.c to query individual values of interest.
Signed-off-by: Jacob Tanenbaum <jtanenba@redhat.com>
Signed-off-by: Thomas Renninger <trenn@suse.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Use sysfs_is_cpu_online(cpu) instead of cpufreq_cpu_exists(cpu) to detect offlined cpus.
Re-arrange printfs slightly to have a consistent output even if you have multiple CPUs
as output and even if offlined cores are in between.
Signed-off-by: Thomas Renninger <trenn@suse.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When working on cpupower code, you often want to compile library code into the
binary.
This allows to execute modified cpupower code, even with library changes
without doing "make install"
Signed-off-by: Thomas Renninger <trenn@suse.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
MSR_PLATFORM_INFO is the new name for MSR_NHM_PLATFORM_INFO
no functional change
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* pm-tools:
Creating a common structure initialization pattern for struct option
cpupower: Enable disabled Cstates if they are below max latency
cpupower: Remove debug message when using cpupower idle-set -D switch
cpupower: cpupower monitor reports uninitialized values for offline cpus
tools/power turbostat: bugfix: print MAX_NON_TURBO_RATIO
tools/power turbostat: simplify Bzy_MHz calculation
This patch tries to creates a common structure initialization
within the cpupower tool.
Previously the ``struct option`` was initialized
using `designated initializer` technique which was
not needed. There were conflicting initialization methods seen with
bench/main.c & others.
Signed-off-by: Sriram Raghunathan <sriram@marirs.net.in>
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
cpupower idle-set -D <latency>
currently only disables all C-states that have a higher latency than the
specified <latency>. But if deep sleep states were already disabled and
have a lower latency, they should get enabled again.
For example:
This call:
cpupower idle-set -D 30
disables all C-states with a higher or equal latency than 30.
If one then calls:
cpupower idle-set -D 100
C-states with a latency between 30-99 will get enabled again with this patch
now. It is ensured that only C-states with a latency of 100 and higher are
disabled.
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
[root@hp-dl980g7-02 linux]# cpupower monitor
...
5472| 0| 1|******|******|******|******|| 0.00| 0.00| 0.00| 0.00| 0.00 *is offline
10567| 0| 159|******|******|******|******|| 0.00| 0.00| 0.00| 0.00| 0.00 *is offline
1661206560|859272560| 150|******|******|******|******|| 0.00| 0.00| 0.00| 0.00| 0.00 *is offline
1661206560|943093104| 140|******|******|******|******|| 0.00| 0.00| 0.00| 0.00| 0.00 *is offline
because of this cpupower also holds the incorrect value for the number
of physical packages in the machine
Changed cpupower to initialize the values of an offline cpu's socket and
core to -1, warn the user that one or more cpus is/are
offline and not print statistics for offline cpus.
This fix hides offlined cores where topology cannot be accessed.
With a recent kernel patch suggested from Prarit Bhargava it may be possible
that soft offlined cores' topology can still be parsed.
This patch would then show which cores in which package/socket are offline,
when sane toplogoy information is available.
Signed-off-by: Jacob Tanenbaum <jtanenba@redhat.com>
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
MSR_TURBO_ACTIVATION_RATIO: 0x00000016 (MAX_NON_TURBO_RATIO=6 lock=0)
should print all 7 bits of MAX_NON_TURBO_RATIO (in decimal):
MSR_TURBO_ACTIVATION_RATIO: 0x00000016 (MAX_NON_TURBO_RATIO=22 lock=0)
Signed-off-by: Len Brown <len.brown@intel.com>
ACPICA commit bed456ed2976bdaafdef406b982fdf6c539befc0
Removed some extraneous defines, reordered others.
Link: https://github.com/acpica/acpica/commit/bed456ed
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Bzy_MHz = TSC_delta*tsc_tweak/APERF_delta/MPERF_delta/measurement_interval
becomes
Bzy_MHz = base_mhz/APERF_delta/MPERF_delta
on systems which support MSR_NHM_PLATFORM_INFO.
base_mhz is calculated directly from the base_ratio
reported in MSR_NHM_PLATFORM_INFO * bclk,
and bclk is discovered via MSR or cpuid.
This reduces the dependency of Bzy_MHz calculation on the TSC.
Previously, there were 4 TSC readings required in each caculation,
the raw TSC delta combined with the measurement_interval.
This also removes the "tsc_tweak" correction factor used when
TSC runs on a different base clock from the CPU's bclk.
After this change, tsc_tweak is used only for %Busy.
The end-result should be a Bzy_MHz result slightly less prone to jitter.
Signed-off-by: Len Brown <len.brown@intel.com>
On a Skylake with 1500MHz base frequency,
the TSC runs at 1512MHz.
This is because the TSC is no longer in the n*100 MHz BCLK domain,
but is now in the m*24MHz crystal clock domain. (24 MHz * 63 = 1512 MHz)
This adds error to several calculations in turbostat,
unless the TSC sample sizes are adjusted for this difference.
Note that calculations in the time domain are immune
from this issue, as the timing sub-system has already
calibrated the TSC against a known wall clock.
AVG_MHz = APERF_delta/measurement_interval
need no adjustment. APERF_delta is in the BCLK domain,
and measurement_interval is in the time domain.
TSC_MHz = TSC_delta/measurement_interval
needs no adjustment -- as we really do want to report
the actual measured TSC delta here, and measurement_interval
is in the accurate time domain.
%Busy = MPERF_delta/TSC_delta
needs adjustment to use TSC_BCLK_DOMAIN_delta.
TSC_BCLK_DOMAIN_delta = TSC_delta * base_hz / tsc_hz
Bzy_MHz = TSC_delta/APERF_delta/MPERF_delta/measurement_interval
need adjustment as above.
No other metrics in turbostat need to be adjusted.
Before:
CPU Avg_MHz %Busy Bzy_MHz TSC_MHz
- 550 24.84 2216 1512
0 2191 98.73 2219 1514
2 0 0.01 2130 1512
1 9 0.43 2016 1512
3 2 0.08 2016 1512
After:
CPU Avg_MHz %Busy Bzy_MHz TSC_MHz
- 550 25.05 2198 1512
0 2190 99.62 2199 1512
2 0 0.01 2152 1512
1 9 0.46 2000 1512
3 2 0.10 2000 1512
Note that in this example, the "Before" Bzy_MHz
was reported as exceeding the 2200 max turbo rate.
Also, even a pinned spin loop would not be reported
as over 99% busy.
Signed-off-by: Len Brown <len.brown@intel.com>
KNL increments APERF and MPERF every 1024 clocks.
This is compliant with the architecture specification,
which requires that only the ratio of APERF/MPERF need be valid.
However, turbostat takes advantage of the fact that these
two MSRs increment every un-halted clock
at the actual and base frequency:
AVG_MHz = APERF_delta/measurement_interval
%Busy = MPERF_delta/TSC_delta
This quirk is needed for these calculations to also work on KNL,
which would otherwise show a value 1024x smaller than expected.
Signed-off-by: Hubert Chrzaniuk <hubert.chrzaniuk@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Staring in Linux-4.3-rc1,
commit 6fb3143b56 ("tools/power turbostat: dump CONFIG_TDP")
touches MSR 0x648, which is not supported on IVB-Xeon.
This results in "turbostat --debug" exiting on those systems:
turbostat: /dev/cpu/2/msr offset 0x648 read failed: Input/output error
Remove IVB-Xeon from the list of machines supporting with that MSR.
Signed-off-by: Len Brown <len.brown@intel.com>
- ACPICA update to upstream revision 20150818 including method
tracing extensions to allow more in-depth AML debugging in the
kernel and a number of assorted fixes and cleanups (Bob Moore,
Lv Zheng, Markus Elfring).
- ACPI sysfs code updates and a documentation update related to
AML method tracing (Lv Zheng).
- ACPI EC driver fix related to serialized evaluations of _Qxx
methods and ACPI tools updates allowing the EC userspace tool
to be built from the kernel source (Lv Zheng).
- ACPI processor driver updates preparing it for future
introduction of CPPC support and ACPI PCC mailbox driver
updates (Ashwin Chaugule).
- ACPI interrupts enumeration fix for a regression related
to the handling of IRQ attribute conflicts between MADT
and the ACPI namespace (Jiang Liu).
- Fixes related to ACPI device PM (Mika Westerberg, Srinidhi Kasagar).
- ACPI device registration code reorganization to separate the
sysfs-related code and bus type operations from the rest (Rafael
J Wysocki).
- Assorted cleanups in the ACPI core (Jarkko Nikula, Mathias Krause,
Andy Shevchenko, Rafael J Wysocki, Nicolas Iooss).
- ACPI cpufreq driver and ia64 cpufreq driver fixes and cleanups
(Pan Xinhui, Rafael J Wysocki).
- cpufreq core cleanups on top of the previous changes allowing it
to preseve its sysfs directories over system suspend/resume (Viresh
Kumar, Rafael J Wysocki, Sebastian Andrzej Siewior).
- cpufreq fixes and cleanups related to governors (Viresh Kumar).
- cpufreq updates (core and the cpufreq-dt driver) related to the
turbo/boost mode support (Viresh Kumar, Bartlomiej Zolnierkiewicz).
- New DT bindings for Operating Performance Points (OPP), support
for them in the OPP framework and in the cpufreq-dt driver plus
related OPP framework fixes and cleanups (Viresh Kumar).
- cpufreq powernv driver updates (Shilpasri G Bhat).
- New cpufreq driver for Mediatek MT8173 (Pi-Cheng Chen).
- Assorted cpufreq driver (speedstep-lib, sfi, integrator) cleanups
and fixes (Abhilash Jindal, Andrzej Hajda, Cristian Ardelean).
- intel_pstate driver updates including Skylake-S support, support
for enabling HW P-states per CPU and an additional vendor bypass
list entry (Kristen Carlson Accardi, Chen Yu, Ethan Zhao).
- cpuidle core fixes related to the handling of coupled idle states
(Xunlei Pang).
- intel_idle driver updates including Skylake Client support and
support for freeze-mode-specific idle states (Len Brown).
- Driver core updates related to power management (Andy Shevchenko,
Rafael J Wysocki).
- Generic power domains framework fixes and cleanups (Jon Hunter,
Geert Uytterhoeven, Rajendra Nayak, Ulf Hansson).
- Device PM QoS framework update to allow the latency tolerance
setting to be exposed to user space via sysfs (Mika Westerberg).
- devfreq support for PPMUv2 in Exynos5433 and a fix for an incorrect
exynos-ppmu DT binding (Chanwoo Choi, Javier Martinez Canillas).
- System sleep support updates (Alan Stern, Len Brown, SungEun Kim).
- rockchip-io AVS support updates (Heiko Stuebner).
- PM core clocks support fixup (Colin Ian King).
- Power capping RAPL driver update including support for Skylake H/S
and Broadwell-H (Radivoje Jovanovic, Seiichi Ikarashi).
- Generic device properties framework fixes related to the handling
of static (driver-provided) property sets (Andy Shevchenko).
- turbostat and cpupower updates (Len Brown, Shilpasri G Bhat,
Shreyas B Prabhu).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=fTgI
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-4.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI updates from Rafael Wysocki:
"From the number of commits perspective, the biggest items are ACPICA
and cpufreq changes with the latter taking the lead (over 50 commits).
On the cpufreq front, there are many cleanups and minor fixes in the
core and governors, driver updates etc. We also have a new cpufreq
driver for Mediatek MT8173 chips.
ACPICA mostly updates its debug infrastructure and adds a number of
fixes and cleanups for a good measure.
The Operating Performance Points (OPP) framework is updated with new
DT bindings and support for them among other things.
We have a few updates of the generic power domains framework and a
reorganization of the ACPI device enumeration code and bus type
operations.
And a lot of fixes and cleanups all over.
Included is one branch from the MFD tree as it contains some
PM-related driver core and ACPI PM changes a few other commits are
based on.
Specifics:
- ACPICA update to upstream revision 20150818 including method
tracing extensions to allow more in-depth AML debugging in the
kernel and a number of assorted fixes and cleanups (Bob Moore, Lv
Zheng, Markus Elfring).
- ACPI sysfs code updates and a documentation update related to AML
method tracing (Lv Zheng).
- ACPI EC driver fix related to serialized evaluations of _Qxx
methods and ACPI tools updates allowing the EC userspace tool to be
built from the kernel source (Lv Zheng).
- ACPI processor driver updates preparing it for future introduction
of CPPC support and ACPI PCC mailbox driver updates (Ashwin
Chaugule).
- ACPI interrupts enumeration fix for a regression related to the
handling of IRQ attribute conflicts between MADT and the ACPI
namespace (Jiang Liu).
- Fixes related to ACPI device PM (Mika Westerberg, Srinidhi
Kasagar).
- ACPI device registration code reorganization to separate the
sysfs-related code and bus type operations from the rest (Rafael J
Wysocki).
- Assorted cleanups in the ACPI core (Jarkko Nikula, Mathias Krause,
Andy Shevchenko, Rafael J Wysocki, Nicolas Iooss).
- ACPI cpufreq driver and ia64 cpufreq driver fixes and cleanups (Pan
Xinhui, Rafael J Wysocki).
- cpufreq core cleanups on top of the previous changes allowing it to
preseve its sysfs directories over system suspend/resume (Viresh
Kumar, Rafael J Wysocki, Sebastian Andrzej Siewior).
- cpufreq fixes and cleanups related to governors (Viresh Kumar).
- cpufreq updates (core and the cpufreq-dt driver) related to the
turbo/boost mode support (Viresh Kumar, Bartlomiej Zolnierkiewicz).
- New DT bindings for Operating Performance Points (OPP), support for
them in the OPP framework and in the cpufreq-dt driver plus related
OPP framework fixes and cleanups (Viresh Kumar).
- cpufreq powernv driver updates (Shilpasri G Bhat).
- New cpufreq driver for Mediatek MT8173 (Pi-Cheng Chen).
- Assorted cpufreq driver (speedstep-lib, sfi, integrator) cleanups
and fixes (Abhilash Jindal, Andrzej Hajda, Cristian Ardelean).
- intel_pstate driver updates including Skylake-S support, support
for enabling HW P-states per CPU and an additional vendor bypass
list entry (Kristen Carlson Accardi, Chen Yu, Ethan Zhao).
- cpuidle core fixes related to the handling of coupled idle states
(Xunlei Pang).
- intel_idle driver updates including Skylake Client support and
support for freeze-mode-specific idle states (Len Brown).
- Driver core updates related to power management (Andy Shevchenko,
Rafael J Wysocki).
- Generic power domains framework fixes and cleanups (Jon Hunter,
Geert Uytterhoeven, Rajendra Nayak, Ulf Hansson).
- Device PM QoS framework update to allow the latency tolerance
setting to be exposed to user space via sysfs (Mika Westerberg).
- devfreq support for PPMUv2 in Exynos5433 and a fix for an incorrect
exynos-ppmu DT binding (Chanwoo Choi, Javier Martinez Canillas).
- System sleep support updates (Alan Stern, Len Brown, SungEun Kim).
- rockchip-io AVS support updates (Heiko Stuebner).
- PM core clocks support fixup (Colin Ian King).
- Power capping RAPL driver update including support for Skylake H/S
and Broadwell-H (Radivoje Jovanovic, Seiichi Ikarashi).
- Generic device properties framework fixes related to the handling
of static (driver-provided) property sets (Andy Shevchenko).
- turbostat and cpupower updates (Len Brown, Shilpasri G Bhat,
Shreyas B Prabhu)"
* tag 'pm+acpi-4.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (180 commits)
cpufreq: speedstep-lib: Use monotonic clock
cpufreq: powernv: Increase the verbosity of OCC console messages
cpufreq: sfi: use kmemdup rather than duplicating its implementation
cpufreq: drop !cpufreq_driver check from cpufreq_parse_governor()
cpufreq: rename cpufreq_real_policy as cpufreq_user_policy
cpufreq: remove redundant 'policy' field from user_policy
cpufreq: remove redundant 'governor' field from user_policy
cpufreq: update user_policy.* on success
cpufreq: use memcpy() to copy policy
cpufreq: remove redundant CPUFREQ_INCOMPATIBLE notifier event
cpufreq: mediatek: Add MT8173 cpufreq driver
dt-bindings: mediatek: Add MT8173 CPU DVFS clock bindings
PM / Domains: Fix typo in description of genpd_dev_pm_detach()
PM / Domains: Remove unusable governor dummies
PM / Domains: Make pm_genpd_init() available to modules
PM / domains: Align column headers and data in pm_genpd_summary output
powercap / RAPL: disable the 2nd power limit properly
tools: cpupower: Fix error when running cpupower monitor
PM / OPP: Drop unlikely before IS_ERR(_OR_NULL)
PM / OPP: Fix static checker warning (broken 64bit big endian systems)
...
* pm-tools:
tools: cpupower: Fix error when running cpupower monitor
tools/power turbostat: fix typo on DRAM column in Joules-mode
cpupower: Do not change the frequency of offline cpu
tools/power turbostat: fix parameter passing for forked command
tools/power turbostat: dump CONFIG_TDP
tools/power turbostat: cpu0 is no longer hard-coded, so update output
tools/power turbostat: update turbostat(8)
* powercap:
powercap / RAPL: disable the 2nd power limit properly
powercap / RAPL: Add support for Broadwell-H
powercap / RAPL: Add support for Skylake H/S
get_cpu_topology() tries to get topology info from all cpus by reading
files in the topology sysfs dir. If a cpu is offlined, since it doesn't
have topology dir, this function fails and returns -1. This causes
functions relying on get_cpu_topology() to fail. For example-
$ cpupower monitor
Cannot read number of available processors
Fix this by skipping fetching topology info for offline cpus.
Signed-off-by: Shreyas B. Prabhu <shreyas@linux.vnet.ibm.com>
Reported-by: Pavaman Subramaniyam <pavsubra@linux.vnet.ibm.com>
Acked-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull turbostat changes for v4.3 from Len Brown.
* 'turbostat' of https://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
tools/power turbostat: fix typo on DRAM column in Joules-mode
tools/power turbostat: fix parameter passing for forked command
tools/power turbostat: dump CONFIG_TDP
tools/power turbostat: cpu0 is no longer hard-coded, so update output
tools/power turbostat: update turbostat(8)
This patch allows EC userspace tool to be built as an ACPI tool.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch splits tools/power/acpi/Makefile to support descend compling for
ACPI tools. In this patch tools/ec related stuff is removed as it is
originally not enabled.
Also a missing .o (utnonansi.o) is added to the acpidump/Makefile.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Check if the cpu is online before changing the frequency/governor of
the cpu.
Reported-by: Pavaman Subramaniyam <pavsubra@linux.vnet.ibm.com>
Signed-off-by: Shilpasri G Bhat <shilpa.bhat@linux.vnet.ibm.com>
Reviewed-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Acked-by: Thomas Renninger <trenn@suse.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
turbostat supports forked command when sampling cpu state. However,
the forked command is not allowed to be executed with options, otherwise
turbostat might regard these options as invalid turbostat options.
For example:
./turbostat stress -c 4 -t 10
./turbostat: unrecognized option '-t'
Reported-by: Chen Yu <yu.c.chen@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Now that there is no paravirt TSC, the "native" is
inappropriate. The function does RDTSC, so give it the obvious
name: rdtsc().
Suggested-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Huang Rui <ray.huang@amd.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Len Brown <lenb@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: kvm ML <kvm@vger.kernel.org>
Link: http://lkml.kernel.org/r/fd43e16281991f096c1e4d21574d9e1402c62d39.1434501121.git.luto@kernel.org
[ Ported it to v4.2-rc1. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Now that the ->read_tsc() paravirt hook is gone, rdtscll() is
just a wrapper around native_read_tsc(). Unwrap it.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Huang Rui <ray.huang@amd.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Len Brown <lenb@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: kvm ML <kvm@vger.kernel.org>
Link: http://lkml.kernel.org/r/d2449ae62c1b1fb90195bcfb19ef4a35883a04dc.1434501121.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
- Fix system resume problems related to 32-bit and 64-bit versions
of the Firmware ACPI Control Structure (FACS) in the firmare (Lv
Zheng).
- Fix double initialization of the FACS (Lv Zheng).
- Add _CLS object processing code to ACPICA (Suravee Suthikulpanit).
- Add support for the (currently missing) new GIC version field in
the Multiple APIC Description Table (MADT) (Hanjun Guo).
- Add support for overriding objects in the ACPI namespace to
ACPICA and OSDT support (Lv Zheng, Bob Moore, Zhang Rui).
- Updates related to the TCPA and TPM2 ACPI tables (Bob Moore).
- Restore the commit modifying _REV to always return "2" (as
required by ACPI 6) and add a blacklisting mechanism for
systems that may be affected by that change (Rafael J Wysocki).
- Assorted fixes and cleanups (Bob Moore, Lv Zheng, Sascha Wildner).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=MlWS
-----END PGP SIGNATURE-----
Merge tag 'acpica-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPICA updates from Rafael Wysocki:
"Additional ACPICA material for v4.2-rc1
This will update the ACPICA code in the kernel to upstream revision
20150619 (a bug-fix release mostly including stable-candidate fixes)
and restore an earlier ACPICA commit that had to be reverted due to a
regression introduced by it (the regression is addressed by
blacklisting the only known system affected by it to date).
The only new feature added by this update is the support for
overriding objects in the ACPI namespace and a new ACPI table that can
be used for that called the Override System Definition Table (OSDT).
That should allow us to "patch" the ACPI namespace built from
incomplete or incorrect ACPI System Definition tables (DSDT, SSDT)
during system startup without the need to provide replacements for all
of those tables in the future.
Specifics:
- Fix system resume problems related to 32-bit and 64-bit versions of
the Firmware ACPI Control Structure (FACS) in the firmare (Lv
Zheng)
- Fix double initialization of the FACS (Lv Zheng)
- Add _CLS object processing code to ACPICA (Suravee Suthikulpanit)
- Add support for the (currently missing) new GIC version field in
the Multiple APIC Description Table (MADT) (Hanjun Guo)
- Add support for overriding objects in the ACPI namespace to ACPICA
and OSDT support (Lv Zheng, Bob Moore, Zhang Rui)
- Updates related to the TCPA and TPM2 ACPI tables (Bob Moore)
- Restore the commit modifying _REV to always return "2" (as required
by ACPI 6) and add a blacklisting mechanism for systems that may be
affected by that change (Rafael J Wysocki)
- Assorted fixes and cleanups (Bob Moore, Lv Zheng, Sascha Wildner)"
* tag 'acpica-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (28 commits)
Revert 'Revert "ACPICA: Permanently set _REV to the value '2'."'
ACPI / init: Make it possible to override _REV
ACPICA: Update version to 20150619
ACPICA: Comment update, no functional change
ACPICA: Update TPM2 ACPI table
ACPICA: Update definitions for the TCPA and TPM2 ACPI tables
ACPICA: Split C library prototypes to new header
ACPICA: De-macroize calls to standard C library functions
ACPI / acpidump: Update acpidump manual
ACPICA: acpidump: Convert the default behavior to dump from /sys/firmware/acpi/tables
ACPICA: acpidump: Allow customized tables to be dumped without accessing /dev/mem
ACPICA: Cleanup output for the ASL Debug object
ACPICA: Update for acpi_install_table memory types
ACPICA: Namespace: Change namespace override to avoid node deletion
ACPICA: Namespace: Add support of OSDT table
ACPICA: Namespace: Add support to allow overriding objects
ACPICA: ACPI 6.0: Add values for MADT GIC version field
ACPICA: Utilities: Add _CLS processing
ACPICA: Add dragon_fly support to unix file mapping file
ACPICA: EFI: Add EFI interface definitions to eliminate dependency of GNU EFI
...
ACPICA commit 3b1026e0bdd3c32eb6d5d313f3ba0b1fee7597b4
ACPICA commit 00f0dc83f5cfca53b27a3213ae0d7719b88c2d6b
ACPICA commit 47d22a738d0e19fd241ffe4e3e9d4e198e4afc69
Across all of ACPICA. Replace C library macros such as ACPI_STRLEN with the
standard names such as strlen. The original purpose for these macros is
long since obsolete.
Also cast various invocations as necessary. Bob Moore, Jung-uk Kim, Lv Zheng.
Link: https://github.com/acpica/acpica/commit/3b1026e0
Link: https://github.com/acpica/acpica/commit/00f0dc83
Link: https://github.com/acpica/acpica/commit/47d22a73
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Jung-uk Kim <jkim@FreeBSD.org>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch updates acpidump manual according to the recent changes.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 04c3bd7e9d6aeb2b3edebe99c90dc271ae4e6353
In order to work without any additional option to dump tables when /dev/mem
doesn't exist, this patch switches the default behavior of acpidump to dump
from /sys/firmware/acpi/tables. Reported by Al Stone, Fixed by Lv Zheng.
Link: https://github.com/acpica/acpica/commit/04c3bd7e
Reported-by: Al Stone <ahs3@redhat.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit ab29013cfa2424140446aff196a70b211ab343a9
The /dev/mem can be configured out, in which case, acpidump should still
work with "-c" option as tables can be found in /sys/firmware/acpi/tables.
This patch allows acpidump to work without /dev/mem.
This patch has been tested with "acpidump -c" and "acpidump -c -n FADT".
And it worked as expected. Lv Zheng.
Link: https://github.com/acpica/acpica/commit/ab29013c
Reported-by: Al Stone <ahs3@redhat.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
- ACPICA update to upstream revision 20150515 including basic
support for ACPI 6 features: new ACPI tables introduced by
ACPI 6 (STAO, XENV, WPBT, NFIT, IORT), changes related to the
other tables (DTRM, FADT, LPIT, MADT), new predefined names
(_BTH, _CR3, _DSD, _LPI, _MTL, _PRR, _RDI, _RST, _TFP, _TSN),
fixes and cleanups (Bob Moore, Lv Zheng).
- ACPI device power management core code update to follow ACPI 6
which reflects the ACPI device power management implementation
in Windows (Rafael J Wysocki).
- Rework of the backlight interface selection logic to reduce the
number of kernel command line options and improve the handling
of DMI quirks that may be involved in that and to make the
code generally more straightforward (Hans de Goede).
- Fixes for the ACPI Embedded Controller (EC) driver related to
the handling of EC transactions (Lv Zheng).
- Fix for a regression related to the ACPI resources management
and resulting from a recent change of ACPI initialization code
ordering (Rafael J Wysocki).
- Fix for a system initialization regression related to ACPI
introduced during the 3.14 cycle and caused by running the
code that switches the platform over to the ACPI mode too
early in the initialization sequence (Rafael J Wysocki).
- Support for the ACPI _CCA device configuration object related
to DMA cache coherence (Suravee Suthikulpanit).
- ACPI/APEI fixes and cleanups (Jiri Kosina, Borislav Petkov).
- ACPI battery driver cleanups (Luis Henriques, Mathias Krause).
- ACPI processor driver cleanups (Hanjun Guo).
- Cleanups and documentation update related to the ACPI device
properties interface based on _DSD (Rafael J Wysocki).
- ACPI device power management fixes (Rafael J Wysocki).
- Assorted cleanups related to ACPI (Dominik Brodowski. Fabian
Frederick, Lorenzo Pieralisi, Mathias Krause, Rafael J Wysocki).
- Fix for a long-standing issue causing General Protection Faults
to be generated occasionally on return to user space after resume
from ACPI-based suspend-to-RAM on 32-bit x86 (Ingo Molnar).
- Fix to make the suspend core code return -EBUSY consistently in
all cases when system suspend is aborted due to wakeup detection
(Ruchi Kandoi).
- Support for automated device wakeup IRQ handling allowing drivers
to make their PM support more starightforward (Tony Lindgren).
- New tracepoints for suspend-to-idle tracing and rework of the
prepare/complete callbacks tracing in the PM core (Todd E Brandt,
Rafael J Wysocki).
- Wakeup sources framework enhancements (Jin Qian).
- New macro for noirq system PM callbacks (Grygorii Strashko).
- Assorted cleanups related to system suspend (Rafael J Wysocki).
- cpuidle core cleanups to make the code more efficient (Rafael J
Wysocki).
- powernv/pseries cpuidle driver update (Shilpasri G Bhat).
- cpufreq core fixes related to CPU online/offline that should
reduce the overhead of these operations quite a bit, unless the
CPU in question is physically going away (Viresh Kumar, Saravana
Kannan).
- Serialization of cpufreq governor callbacks to avoid race
conditions in some cases (Viresh Kumar).
- intel_pstate driver fixes and cleanups (Doug Smythies, Prarit
Bhargava, Joe Konno).
- cpufreq driver (arm_big_little, cpufreq-dt, qoriq) updates (Sudeep
Holla, Felipe Balbi, Tang Yuantian).
- Assorted cleanups in cpufreq drivers and core (Shailendra Verma,
Fabian Frederick, Wang Long).
- New Device Tree bindings for representing Operating Performance
Points (Viresh Kumar).
- Updates for the common clock operations support code in the PM
core (Rajendra Nayak, Geert Uytterhoeven).
- PM domains core code update (Geert Uytterhoeven).
- Intel Knights Landing support for the RAPL (Running Average Power
Limit) power capping driver (Dasaratharaman Chandramouli).
- Fixes related to the floor frequency setting on Atom SoCs in the
RAPL power capping driver (Ajay Thomas).
- Runtime PM framework documentation update (Ben Dooks).
- cpupower tool fix (Herton R Krzesinski).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=7jTj
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI updates from Rafael Wysocki:
"The rework of backlight interface selection API from Hans de Goede
stands out from the number of commits and the number of affected
places perspective. The cpufreq core fixes from Viresh Kumar are
quite significant too as far as the number of commits goes and because
they should reduce CPU online/offline overhead quite a bit in the
majority of cases.
From the new featues point of view, the ACPICA update (to upstream
revision 20150515) adding support for new ACPI 6 material to ACPICA is
the one that matters the most as some new significant features will be
based on it going forward. Also included is an update of the ACPI
device power management core to follow ACPI 6 (which in turn reflects
the Windows' device PM implementation), a PM core extension to support
wakeup interrupts in a more generic way and support for the ACPI _CCA
device configuration object.
The rest is mostly fixes and cleanups all over and some documentation
updates, including new DT bindings for Operating Performance Points.
There is one fix for a regression introduced in the 4.1 cycle, but it
adds quite a number of lines of code, it wasn't really ready before
Thursday and you were on vacation, so I refrained from pushing it on
the last minute for 4.1.
Specifics:
- ACPICA update to upstream revision 20150515 including basic support
for ACPI 6 features: new ACPI tables introduced by ACPI 6 (STAO,
XENV, WPBT, NFIT, IORT), changes related to the other tables (DTRM,
FADT, LPIT, MADT), new predefined names (_BTH, _CR3, _DSD, _LPI,
_MTL, _PRR, _RDI, _RST, _TFP, _TSN), fixes and cleanups (Bob Moore,
Lv Zheng).
- ACPI device power management core code update to follow ACPI 6
which reflects the ACPI device power management implementation in
Windows (Rafael J Wysocki).
- rework of the backlight interface selection logic to reduce the
number of kernel command line options and improve the handling of
DMI quirks that may be involved in that and to make the code
generally more straightforward (Hans de Goede).
- fixes for the ACPI Embedded Controller (EC) driver related to the
handling of EC transactions (Lv Zheng).
- fix for a regression related to the ACPI resources management and
resulting from a recent change of ACPI initialization code ordering
(Rafael J Wysocki).
- fix for a system initialization regression related to ACPI
introduced during the 3.14 cycle and caused by running the code
that switches the platform over to the ACPI mode too early in the
initialization sequence (Rafael J Wysocki).
- support for the ACPI _CCA device configuration object related to
DMA cache coherence (Suravee Suthikulpanit).
- ACPI/APEI fixes and cleanups (Jiri Kosina, Borislav Petkov).
- ACPI battery driver cleanups (Luis Henriques, Mathias Krause).
- ACPI processor driver cleanups (Hanjun Guo).
- cleanups and documentation update related to the ACPI device
properties interface based on _DSD (Rafael J Wysocki).
- ACPI device power management fixes (Rafael J Wysocki).
- assorted cleanups related to ACPI (Dominik Brodowski, Fabian
Frederick, Lorenzo Pieralisi, Mathias Krause, Rafael J Wysocki).
- fix for a long-standing issue causing General Protection Faults to
be generated occasionally on return to user space after resume from
ACPI-based suspend-to-RAM on 32-bit x86 (Ingo Molnar).
- fix to make the suspend core code return -EBUSY consistently in all
cases when system suspend is aborted due to wakeup detection (Ruchi
Kandoi).
- support for automated device wakeup IRQ handling allowing drivers
to make their PM support more starightforward (Tony Lindgren).
- new tracepoints for suspend-to-idle tracing and rework of the
prepare/complete callbacks tracing in the PM core (Todd E Brandt,
Rafael J Wysocki).
- wakeup sources framework enhancements (Jin Qian).
- new macro for noirq system PM callbacks (Grygorii Strashko).
- assorted cleanups related to system suspend (Rafael J Wysocki).
- cpuidle core cleanups to make the code more efficient (Rafael J
Wysocki).
- powernv/pseries cpuidle driver update (Shilpasri G Bhat).
- cpufreq core fixes related to CPU online/offline that should reduce
the overhead of these operations quite a bit, unless the CPU in
question is physically going away (Viresh Kumar, Saravana Kannan).
- serialization of cpufreq governor callbacks to avoid race
conditions in some cases (Viresh Kumar).
- intel_pstate driver fixes and cleanups (Doug Smythies, Prarit
Bhargava, Joe Konno).
- cpufreq driver (arm_big_little, cpufreq-dt, qoriq) updates (Sudeep
Holla, Felipe Balbi, Tang Yuantian).
- assorted cleanups in cpufreq drivers and core (Shailendra Verma,
Fabian Frederick, Wang Long).
- new Device Tree bindings for representing Operating Performance
Points (Viresh Kumar).
- updates for the common clock operations support code in the PM core
(Rajendra Nayak, Geert Uytterhoeven).
- PM domains core code update (Geert Uytterhoeven).
- Intel Knights Landing support for the RAPL (Running Average Power
Limit) power capping driver (Dasaratharaman Chandramouli).
- fixes related to the floor frequency setting on Atom SoCs in the
RAPL power capping driver (Ajay Thomas).
- runtime PM framework documentation update (Ben Dooks).
- cpupower tool fix (Herton R Krzesinski)"
* tag 'pm+acpi-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (194 commits)
cpuidle: powernv/pseries: Auto-promotion of snooze to deeper idle state
x86: Load __USER_DS into DS/ES after resume
PM / OPP: Add binding for 'opp-suspend'
PM / OPP: Allow multiple OPP tables to be passed via DT
PM / OPP: Add new bindings to address shortcomings of existing bindings
ACPI: Constify ACPI device IDs in documentation
ACPI / enumeration: Document the rules regarding the PRP0001 device ID
ACPI / video: Make acpi_video_unregister_backlight() private
acpi-video-detect: Remove old API
toshiba-acpi: Port to new backlight interface selection API
thinkpad-acpi: Port to new backlight interface selection API
sony-laptop: Port to new backlight interface selection API
samsung-laptop: Port to new backlight interface selection API
msi-wmi: Port to new backlight interface selection API
msi-laptop: Port to new backlight interface selection API
intel-oaktrail: Port to new backlight interface selection API
ideapad-laptop: Port to new backlight interface selection API
fujitsu-laptop: Port to new backlight interface selection API
eeepc-laptop: Port to new backlight interface selection API
dell-wmi: Port to new backlight interface selection API
...
* pnp:
PNP / ACPI: use unsigned int in pnpacpi_encode_resources()
PNP / ACPI: use u8 instead of int in acpi_resource_extended_irq context
* pm-tools:
cpupower: mperf monitor: fix output in MAX_FREQ_SYSFS mode
Config TDP is a feature that allows parts to be configured
for different thermal limits after they have left the factory.
This can have an effect on the operation of the part,
particularly in determiniing...
Max Non-turbo Ratio
Turbo Activation Ratio
Signed-off-by: Len Brown <len.brown@intel.com>
The --debug option reads a number of per-package MSRs.
Previously we explicitly read them on cpu0, but recently
turbostat changed to read them on the current "base_cpu".
Update the print-out to reflect base_cpu, rather than
the hard-coded cpu0.
Signed-off-by: Len Brown <len.brown@intel.com>
This header containing all MSRs and respective bit definitions
got exported to userspace in conjunction with the big UAPI
shuffle.
But, it doesn't belong in the UAPI headers because userspace can
do its own MSR defines and exporting them from the kernel blocks
us from doing cleanups/renames in that header. Which is
ridiculous - it is not kernel's job to export such a header and
keep MSRs list and their names stable.
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1433436928-31903-19-git-send-email-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Remove reference to the original Nehalem Turbo white paper,
since it has moved, and these mechanisms have now long since
been documented in the Software Developer's Manual.
Reported-by: Jeremie Lagraviere <jeremie@simula.no>
Signed-off-by: Len Brown <len.brown@intel.com>
There is clearly wrong output when mperf monitor runs in MAX_FREQ_SYSFS mode:
average frequency shows in kHz unit (despite the intended output to be in MHz),
and percentages for C state information are all wrong (including high/negative
values shown).
The problem is that the max_frequency read on initialization isn't used where it
should have been used on mperf_get_count_percent (to estimate the number of
ticks in the given time period), and the value we read from sysfs is in kHz, so
we must divide it to get the MHz value to use in current calculations.
While at it, also I fixed another small issues in the debug output of
max_frequency value in mperf_get_count_freq.
Signed-off-by: Herton R. Krzesinski <herton@redhat.com>
Acked-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Linux-3.7 added CONFIG_BOOTPARAM_HOTPLUG_CPU0,
allowing systems to offline cpu0.
But when cpu0 is offline, turbostat will not run:
# turbostat ls
turbostat: no /dev/cpu/0/msr
This patch replaces the hard-coded use of cpu0 in turbostat
with the current cpu, allowing it to run without a cpu0.
Fewer cross-calls may also be needed due to use of current cpu,
though this hard-coding was used only for the --debug preamble.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Len Brown <len.brown@intel.com>
When EPB is 0xF, turbosat was incorrectly describing it as "custom"
instead of calling it "powersave":
< cpu0: MSR_IA32_ENERGY_PERF_BIAS: 0x0000000f (custom)
> cpu0: MSR_IA32_ENERGY_PERF_BIAS: 0x0000000f (powersave)
Signed-off-by: Len Brown <len.brown@intel.com>
Changes mainly to account for minor differences in Knights Landing(KNL):
1. KNL supports C1 and C6 core states.
2. KNL supports PC2, PC3 and PC6 package states.
3. KNL has a different encoding of the TURBO_RATIO_LIMIT MSR
Signed-off-by: Dasaratharaman Chandramouli <dasaratharaman.chandramouli@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Without this update, turbostat displays only 2 threads per core.
Some processors, such as Xeon Phi, have more.
Signed-off-by: Dasaratharaman Chandramouli <dasaratharaman.chandramouli@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
- Fix a build warning in the intel_pstate driver showing up in non-SMP
builds (Borislav Petkov).
- Change one of the intel_pstate's P-state selection parameters for
Baytrail and Cherrytrail CPUs to significantly improve performance
at the cost of a small increase in energy consumption (Kristen
Carlson Accardi).
- Fix a NULL pointer dereference in the ACPI EC driver due to an unsafe
list walk in the query handler removal routine (Chris Bainbridge).
- Get rid of a false-positive lockdep warning in the ACPI container
hot-remove code (Rafael J Wysocki).
- Prevent the ACPI device enumeration code from creating device
objects of a wrong type in some cases (Rafael J Wysocki).
- Add Skylake processors support to the Intel RAPL power capping
driver (Brian Bian).
- Drop the stale MAINTAINERS entry for the ACPI dock driver that is
regarded as part of the ACPI core and maintained along with it now
(Chao Yu).
- Fix cpupower tool breakage caused by a library API change in libpci
3.3.0 (Lucas Stach).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQIcBAABCAAGBQJVOoMNAAoJEILEb/54YlRxx+QP/A/gaX9GgB6rv627Khlaw2AK
PpE1SrJoU9jAEwPqXtRnYc/6nducDzO5XaHOdWaV02YCpKLL5vIyia6wcy7cf4kr
6vJUnBz0OiHjp4e4sYrvIGt7RrLnlodayKAzNgtjDjF2JE3gzOOldD0klcfisiUP
Uc7Y3bpFndS8fwpcJO0tGm73aA9kNC5N8sYxgtuv/OAeMmJgi0fIi2V227XIurJU
48nMJ1v7M3OChmhdfxEtUSR9TM8J0Ck3yJwPYORNFItRCGqHJb3WY6lo1kbNcv1g
SLwbw+nCaq+E4k2PtDAsg68Ni0uGGnytcBTzhtPeUOdPRulp4CHCnZEyMUBwFVV8
gZlgL2S3CxcBlZ52hVB9tAhAyRcxmaWrp1v/hNsTh1xX9v9JFUFdpjYvk1RlHKwD
aT30G1mV8icU9lrYzhNOnh9gMrZVv6wy4sp4Uk1NLa17WXu+p0LMrCX8HJEb3PT3
rYZ8jbzo422lTksopiLTLhY4ipgX+kysa7NhTtw/J5Hb9xctho0uTsIhP6sSkh2e
eHO8WthEpF36228n6qiGGTBMcs4xPD8goxXCeBmgsBeVAQDaVR1IcArVTS+HAaJX
KOhemws+ThpEpjqB8jbpa42OEmY1Um3UUufHwnJIX54vGkSlXBxXE9r3hCwK7Mgu
hQhnM9hargHcy9Z8vd91
=0bKD
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-4.1-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more power management and ACPI updates from Rafael Wysocki:
"These are fixes mostly (intel_pstate, ACPI core, ACPI EC driver,
cpupower tool), a new CPU ID for the Intel RAPL driver and one
intel_pstate driver improvement that didn't make it to my previous
pull requests due to timing.
Specifics:
- Fix a build warning in the intel_pstate driver showing up in
non-SMP builds (Borislav Petkov)
- Change one of the intel_pstate's P-state selection parameters for
Baytrail and Cherrytrail CPUs to significantly improve performance
at the cost of a small increase in energy consumption (Kristen
Carlson Accardi)
- Fix a NULL pointer dereference in the ACPI EC driver due to an
unsafe list walk in the query handler removal routine (Chris
Bainbridge)
- Get rid of a false-positive lockdep warning in the ACPI container
hot-remove code (Rafael J Wysocki)
- Prevent the ACPI device enumeration code from creating device
objects of a wrong type in some cases (Rafael J Wysocki)
- Add Skylake processors support to the Intel RAPL power capping
driver (Brian Bian)
- Drop the stale MAINTAINERS entry for the ACPI dock driver that is
regarded as part of the ACPI core and maintained along with it now
(Chao Yu)
- Fix cpupower tool breakage caused by a library API change in libpci
3.3.0 (Lucas Stach)"
* tag 'pm+acpi-4.1-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / scan: Add a scan handler for PRP0001
ACPI / scan: Annotate physical_node_lock in acpi_scan_is_offline()
ACPI / EC: fix NULL pointer dereference in acpi_ec_remove_query_handler()
MAINTAINERS: remove maintainship entry of docking station driver
powercap / RAPL: Add support for Intel Skylake processors
cpufreq: intel_pstate: Fix an annoying !CONFIG_SMP warning
intel_pstate: Change the setpoint for Atom params
cpupower: fix breakage from libpci API change
Pull turbostat update from Len Brown:
"Updates to the turbostat utility.
Just one kernel dependency in this batch -- added a #define to
msr-index.h"
* 'turbostat' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
tools/power turbostat: correct dumped pkg-cstate-limit value
tools/power turbostat: calculate TSC frequency from CPUID(0x15) on SKL
tools/power turbostat: correct DRAM RAPL units on recent Xeon processors
tools/power turbostat: Initial Skylake support
tools/power turbostat: Use $(CURDIR) instead of $(PWD) and add support for O= option in Makefile
tools/power turbostat: modprobe msr, if needed
tools/power turbostat: dump MSR_TURBO_RATIO_LIMIT2
tools/power turbostat: use new MSR_TURBO_RATIO_LIMIT names
x86 msr-index: define MSR_TURBO_RATIO_LIMIT,1,2
tools/power turbostat: label base frequency
tools/power turbostat: update PERF_LIMIT_REASONS decoding
tools/power turbostat: simplify default output
* pm-cpufreq:
cpufreq: intel_pstate: Fix an annoying !CONFIG_SMP warning
intel_pstate: Change the setpoint for Atom params
* powercap:
powercap / RAPL: Add support for Intel Skylake processors
* pm-tools:
cpupower: fix breakage from libpci API change
HSW expanded MSR_PKG_CST_CONFIG_CONTROL.Package-C-State-Limit,
from bits[2:0] used by previous implementations, to [3:0].
The value 1000b is unlimited, and is used by BDW and SKL too.
Signed-off-by: Len Brown <len.brown@intel.com>
While not yet documented in the Software Developer's Manual,
the data-sheet for modern Xeon states that DRAM RAPL ENERGY units
are fixed at 15.3 uJ, rather than being discovered via MSR.
Before this patch, DRAM energy on these products is over-stated by turbostat
because the RAPL units are 4x larger.
ref: "Xeon E5-2600 v3/E5-1600 v3 Datasheet Volume 2"
http://www.intel.com/content/dam/www/public/us/en/documents/datasheets/xeon-e5-v3-datasheet-vol-2.pdf
Signed-off-by: Andrey Semin <andrey.semin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Skylake adds some additional residency counters.
Skylake supports a different mix of RAPL registers
from any previous product.
In most other ways, Skylake is like Broadwell.
Signed-off-by: Len Brown <len.brown@intel.com>
Since commit ee0778a301
("tools/power: turbostat: make Makefile a bit more capable")
turbostat's Makefile is using
[...]
BUILD_OUTPUT := $(PWD)
[...]
which obviously causes trouble when building "turbostat" with
make -C /usr/src/linux/tools/power/x86/turbostat ARCH=x86 turbostat
because GNU make does not update nor guarantee that $PWD is set.
This patch changes the Makefile to use $CURDIR instead, which GNU make
guarantees to set and update (i.e. when using "make -C ...") and also
adds support for the O= option (see "make help" in your root of your
kernel source tree for more details).
Link: https://bugs.gentoo.org/show_bug.cgi?id=533918
Fixes: ee0778a301 ("tools/power: turbostat: make Makefile a bit more capable")
Signed-off-by: Thomas D. <whissi@whissi.de>
Cc: Mark Asselstine <mark.asselstine@windriver.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Colin Ian King
Mattia Dongili
Lv Zheng
Rafael J. Wysocki
Len Brown
Bob Moore
Will Miles
Linus Torvalds
Chen Yu
Hubert Chrzaniuk
Shreyas B. Prabhu
Jacob Tanenbaum
Thomas Renninger
Sriram Raghunathan
Thomas Renninger
Shilpasri G Bhat
Andy Lutomirski
Sascha Wildner
Borislav Petkov
Herton R. Krzesinski
Prarit Bhargava
Dasaratharaman Chandramouli
Rafael J. Wysocki
Andrey Semin
Thomas D