spi framework should allocate bus number dynamically either
via Linux IDR or spi alias for master drivers. This patch deletes
code pertaining to manual allocation of spi bus number in spi omap2
master driver.
Signed-off-by: Suniel Mahesh <sunil.m@techveda.org>
Signed-off-by: Karthik Tummala <karthik@techveda.org>
Tested-by: Karthik Tummala <karthik@techveda.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The check to see if status is less than zero is actually redundant
as all previous places where it is -ve have already branched to the
exit paths, so it is never less than zero at the check.
Detected by CoverityScan, CID#1357119 ("Logically dead code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When running the spi-loopback-test with slower clock rate like 10 KHz,
the test for 251 bytes transfer was failed. This failure triggered an
spi-omap2-mcspi's error message "DMA RX last word empty".
This message means that PIO for reading the remaining bytes due to the
DMA transfer length reduction is failed. This problem can be fixed by
polling OMAP2_MCSPI_CHSTAT_RXS bit in channel status register to wait
until the receive buffer register is filled.
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove unneeded error handling on the result of a call
to platform_get_resource() when the value is passed to
devm_ioremap_resource().
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
currently during probe the resource data gets modified and device
physical address remains valid only during first load. If the module is
unloaded and loaded again, the ioremp will be done on a incorrect address
as the resource was modified during previous module load.
This patch fixes this issue.
Signed-off-by: Vikram N <vicky773@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently, the driver handles mapping buffers to be used by the DMA.
However, there are times that the current mapping implementation will
fail for certain buffers. Fortunately, the SPI framework can detect
and map buffers so its usable by the DMA.
Update the driver to utilize the SPI framework for buffer
mapping instead. Also incorporate hooks that the framework uses to
determine if the DMA can or can not be used.
This will result in the original omap2_mcspi_transfer_one function being
deleted and omap2_mcspi_work_one being renamed to
omap2_mcspi_transfer_one. Previously transfer_one was only responsible
for mapping and work_one handled the transfer. But now only transferring
needs to be handled by the driver.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
OMAP35x and OMAP37x mentions in the McSPI End-of-Transfer Sequences section
that if the McSPI is configured as a Master and only DMA RX is being
performed then the DMA transfer size needs to be reduced by 1 or 2.
This was originally implemented by:
commit 57c5c28dbc ("spi: omap2_mcspi rxdma bugfix")
This patch adds comments to clarify what is going on in the code since its
not obvious what problem its addressing.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
With the new dma_request_chan() the client driver does not need to look for
the DMA resource and it does not need to pass filter_fn anymore.
By switching to the new API the driver can now support deferred probing
against DMA.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 5de85b9d57 ("PM / runtime: Re-init runtime PM states at probe
error and driver unbind") introduced pm_runtime_reinit() that is used
to reinitialize PM runtime after -EPROBE_DEFER. This allows shutting
down the device after a failed probe.
However, for drivers using pm_runtime_use_autosuspend() this can cause
a state where suspend callback is never called after -EPROBE_DEFER.
On the following device driver probe, hardware state is different from
the PM runtime state causing omap_device to produce the following
error:
omap_device_enable() called from invalid state 1
And with omap_device and omap hardware being picky for PM, this will
block any deeper idle states in hardware.
The solution is to fix the drivers to follow the PM runtime documentation:
1. For sections of code that needs the device disabled, use
pm_runtime_put_sync_suspend() if pm_runtime_set_autosuspend() has
been set.
2. For driver exit code, use pm_runtime_dont_use_autosuspend() before
pm_runtime_put_sync() if pm_runtime_use_autosuspend() has been
set.
Fixes: 5de85b9d57 ("PM / runtime: Re-init runtime PM states at probe
error and driver unbind")
Cc: linux-spi@vger.kernel.org
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Nishanth Menon <nm@ti.com>
Cc: Rafael J. Wysocki <rafael@kernel.org>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Occasionally the setup function will be called multiple times. Only request
the gpio the first time otherwise -EBUSY will occur on subsequent calls to
setup.
Reported-by: Joseph Bell <joe@iachieved.it>
Signed-off-by: Michael Welling <mwelling@ieee.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This adds calls to pinctrl subsystem in order to switch pin states
on suspend/resume if you provide a "sleep" state in DT.
If no "sleep" state is provided in DT, these calls turn
to NOPs.
Signed-off-by: Pascal Huerst <pascal.huerst@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since the "Switch driver to use transfer_one" change, the cs_change
behavior has changed and a channel chip select can still be
asserted when changing channel from a previous last transfer in a
message having the cs_change attribute.
Since there is no sense having multiple chip select being asserted at the
same time, disable all the remaining forced chip selects in a the
prepare_message called right before a spi_transfer_one_message call.
It ignores the current channel configuration in order to keep the
possibility to leave the chip select asserted between messages.
It fixes this bug on a DM8168 SoC ES2.1 Soc and an OMAP4 ES2.1 SoC.
It was hanging all the other channels transfers when a CHCONF_FORCE
is present on the wrong channel.
Fixes: b28cb9414d ("spi: omap2-mcspi: Switch driver to use transfer_one")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Michael Welling <mwelling@ieee.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since commit ddcad7e906 omap2_mcspi_set_cs() is called without
runtime power management requested. This patch fixes the problem by
requesting runtime power management in omap2_mcspi_set_cs().
Reported-By: Pali Rohár <pali.rohar@gmail.com>
Fixes: ddcad7e906 (spi: omap2-mcspi: Fix native cs with new set_cs)
Tested-By: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Acked-by: Michael Welling <mwelling@ieee.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
If a valid GPIO is specified but cannot be requested by the driver, print a
message and error out of omap2_mcspi_setup.
Signed-off-by: Michael Welling <mwelling@ieee.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The OMAP2_MCSPI_CHCONF_FORCE must be toggled even when using GPIO
chip selects. This patch conditionally calls the omap2_mcspi_set_cs
function to do so when using GPIO chip selects.
Signed-off-by: Michael Welling <mwelling@ieee.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The core spi driver swaps the polarity of the enable based on SPI_CS_HIGH.
The omap2 controller has an internal configuration register bit called
OMAP2_MCSPI_CHCONF_EPOL to handle active high chip selects as well.
So we have to revert swap the polarity back for the correct setting of the
OMAP2_MCSPI_CHCONF_FORCE bit in omap2_mcspi_set_cs.
Signed-off-by: Michael Welling <mwelling@ieee.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The core spi driver handles the delay between transactions.
This is a remanant from the transfer_one conversion.
Signed-off-by: Michael Welling <mwelling@ieee.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
GPIO chip select patch series appears to have broken the native chip select
support. This patch pulls the manual native chip select toggling out of
the transfer_one routine and adds a set_cs routine.
Tested natively on AM3354 with SPI serial flash on spi0cs0.
Reported-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Michael Welling <mwelling@ieee.org>
Tested-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If GPIO chip select is specified, request the GPIO in the setup function
and release it in the cleanup function.
Signed-off-by: Michael Welling <mwelling@ieee.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Switches from transfer_one_message to transfer_one to prepare driver for
use of GPIO chip selects.
Signed-off-by: Michael Welling <mwelling@ieee.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The spi queue waits forever for spi_finalize_current_message() to be
called, blocking the bus. Ensure that all error paths from
omap2_mcspi_transfer_one_message() call spi_finalize_current_message().
Signed-off-by: Fionn Cleary <fionn.cleary@streamunlimited.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The spi hangs waiting the completion of omap2_mcspi_rx_callback.
Signed-off-by: Jorge A. Ventura <jorge.araujo.ventura@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
Commit id 2bd16e3e23
(spi: omap2-mcspi: Do not configure the controller
on each transfer unless needed) does its job too
well so omap2_mcspi_setup_transfer() isn't called
even when an SPI slave driver changes 'spi->mode'.
The result is that the mode requested by the SPI
slave driver never takes effect.
Fix this by adding the 'mode' member to the
omap2_mcspi_cs structure which holds the mode
value that the hardware is configured for.
When the SPI slave driver changes 'spi->mode'
it will be different than the value of this new
member and the SPI master driver will know that
the hardware must be reconfigured (by calling
omap2_mcspi_setup_transfer()).
Fixes: 2bd16e3e23 (spi: omap2-mcspi: Do not configure the controller on each transfer unless needed)
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
This saves a few unwind code and return proper error if devm_kcalloc fails.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Set master->max_speed_hz and master->min_speed_hz then spi core will handle
checking transfer speed. So we can remove the same checking in this driver.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Currently a divide-by-2^n clock is used, causing a very coarse
clock selection, i.e. a 10MHz device will need to use a 6MHz
clock. The McSPI can also use a divide-by-n clock, this patch
adds support for selecting that when possible.
Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
spi_transfer->speed_hz and spi_transfer->bits_per_word used to only be set when
not using the default settings but are not set on every transfer, causing
omap2_mcspi_setup_transfer to be called on each transfer. This patch changes
the check to only call omap2_mcspi_setup_transfer if the settings needs to be
changed.
Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
All OMAP IP blocks expect LE data, but CPU may operate in BE mode.
Need to use endian neutral functions to read/write h/w registers.
I.e instead of __raw_read[lw] and __raw_write[lw] functions code
need to use read[lw]_relaxed and write[lw]_relaxed functions.
If the first simply reads/writes register, the second will byteswap
it if host operates in BE mode.
Changes are trivial sed like replacement of __raw_xxx functions
with xxx_relaxed variant.
Signed-off-by: Victor Kamensky <victor.kamensky@linaro.org>
Signed-off-by: Taras Kondratiuk <taras.kondratiuk@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch fixes MCSPI FIFO buffer support when transmit-and-receive
(full duplex) mode is used. In this mode FIFO can be used for RX or
for TX or for both directions. If FIFO used for both directions the buffer
is split into two 32-byte buffers - one for each direction.
Also for full duplex mode both AEL and AFL need to be set in CHCONF0 register.
Signed-off-by: Illia Smyrnov <illia.smyrnov@globallogic.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use devm_spi_register_master() to make cleanup paths simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Convert dmaengine channel requests to use
dma_request_slave_channel_compat(). This supports the DT case of
platforms requiring channel selection from either the OMAP DMA or
the EDMA engine. AM33xx only boots from DT and is the only user
implementing EDMA so in the !DT case we can default to the OMAP DMA
filter.
Signed-off-by: Matt Porter <mporter@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Joel A Fernandes <joelagnel@ti.com>
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The MCSPI controller has a built-in FIFO buffer to unload the DMA or interrupt
handler and improve data throughput. This patch adds FIFO buffer support for SPI
transfers in DMA mode.
For SPI transfers in DMA mode, the largest possible FIFO buffer size will be
calculated and set up. The FIFO won't be used for the SPI transfers in DMA mode
if: calculated FIFO buffer size is less then 2 bytes or the FIFO buffer size
isn't multiple of the SPI word length.
Signed-off-by: Illia Smyrnov <illia.smyrnov@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Introduce mcspi_bytes_per_word function as replacement for the next code
fragment:
int c = (word_len <= 8) ? 1 :
(word_len <= 16) ? 2 :
/* word_len <= 32 */ 4;
This code used 2 times in current driver code and will be used 2 times in
the next FIFO buffer support patch. Replace it with inline function with clear
name to improve code legibility.
Signed-off-by: Illia Smyrnov <illia.smyrnov@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Fill in the recently added spi_master.bits_per_word_mask field in as
many drivers as possible. Make related cleanups, such as removing any
redundant error-checking, or empty setup callbacks.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use the wrapper functions for getting and setting the driver data using
platform_device instead of using dev_{get,set}_drvdata() with &pdev->dev,
so we can directly pass a struct platform_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Since commit ab78029 (drivers/pinctrl: grab default handles from device
core) we can rely on device core for handling pinctrl so remove
devm_pinctrl_get_select_default() from the driver.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Suniel Mahesh
Colin Ian King
Akinobu Mita
Wei Yongjun
Vikram N
Franklin S Cooper Jr
Peter Ujfalusi
Tony Lindgren
Michael Welling
Pascal Huerst
Neil Armstrong
Sebastian Reichel
Fionn Cleary
Jarkko Nikula
Wolfram Sang
Jorge A. Ventura
Mark A. Greer
Mark Brown
Axel Lin
Stefan Sørensen
Paul Gortmaker
Victor Kamensky
Illia Smyrnov
Jingoo Han
Matt Porter
Illia Smyrnov
Stephen Warren
Mark Brown