When suspending to RAM, the power to the core is cut and the register
values are lost. Save and restore more registers than just IMR.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Correct the incorrect function name and description.
Fixes: a76edc89b1 ("pinctrl: core: Add generic pinctrl functions for managing groups")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add pinctrl driver support for the Axis ARTPEC-6 SoC.
There are only some pins that actually have different
functions available, but all can control bias (pull-up/-down)
and drive strength.
Code originally written by Chris Paterson.
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The NAND DQS pins are currently named nand_dqs_0 and nand_dqs_1.
However, they both seem to have the same function, just exposed on
different pins (unlike the ethernet TX pins for example, where there's
eth_txd0..3 - all of these can be active at the same time as they are
different data lines).
Rename the NAND DQS pins to nand_dqs_15 and nand_dqs_18 to reflect that
it's the same functionality just exposed on different pins (BOOT_15 and
BOOT_18).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The nand_groups table uses different names for the NAND DQS pins than
the GROUP() definition in meson8b_cbus_groups (nand_dqs_0 vs nand_dqs0).
This prevents using the NAND DQS pins in the devicetree.
Fix this by ensuring that the GROUP() definition and the
meson8b_cbus_groups use the same name for these pins.
Fixes: 0fefcb6876 ("pinctrl: Add support for Meson8b")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Recent pinctrl changes to allow dynamic allocation of pins exposed one
more issue with the pinctrl pins claimed early by the controller itself.
This caused a regression for IMX6 pinctrl hogs.
Before enabling the pin controller driver we need to wait until it has
been properly initialized, then claim the hogs, and only then enable it.
To fix the regression, split the code into pinctrl_claim_hogs() and
pinctrl_enable(). And then let's require that pinctrl_enable() is always
called by the pin controller driver when ready after calling
pinctrl_register_and_init().
Depends-on: 950b0d91dc ("pinctrl: core: Fix regression caused by delayed
work for hogs")
Fixes: df61b366af26 ("pinctrl: core: Use delayed work for hogs")
Fixes: e566fc11ea ("pinctrl: imx: use generic pinctrl helpers for
managing groups")
Cc: Haojian Zhuang <haojian.zhuang@linaro.org>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Mika Penttilä <mika.penttila@nextfour.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Stefan Agner <stefan@agner.ch>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Gary Bisson <gary.bisson@boundarydevices.com>
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
All R8A7794 manuals I have here (0.50 and 1.10) agree that the PFC driver
has ATAG0# and ATAWR0# signals in IPSR12 swapped -- fix this.
Fixes: 43c4436e2f ("pinctrl: sh-pfc: add R8A7794 PFC support")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
- Add basic support for the Pin Function Controller on revision ES2.0
of the R-Car H3 SoC, which differs from ES1.x in many ways.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=fKYc
-----END PGP SIGNATURE-----
Merge tag 'sh-pfc-for-v4.12-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into devel
pinctrl: sh-pfc: Updates for v4.12 (take two)
- Add basic support for the Pin Function Controller on revision ES2.0
of the R-Car H3 SoC, which differs from ES1.x in many ways.
The IPSR field names in the comments have been fat-fingered in a couple
places -- fix those silly typos...
Fixes: 5088451962 ("pinctrl: sh-pfc: r8a7791 PFC support")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
PINMUX_IPSR_MSEL() macro invocation for the TX2 signal has apparently wrong
1st argument -- most probably a result of cut&paste programming...
Fixes: 5088451962 ("pinctrl: sh-pfc: r8a7791 PFC support")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The R8A7791 PFC driver was apparently based on the preliminary revisions
of the user's manual, which omitted the DVC_MUTE signal altogether in
the PFC section. The modern manual has the signal described, so just add
the necassary data to the driver...
Fixes: 5088451962 ("pinctrl: sh-pfc: r8a7791 PFC support")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The R8A7791 PFC driver was apparently based on the preliminary revisions
of the user's manual, which omitted the HSCIF1 group E signals in the
IPSR4 register description. This would cause HSCIF1's probe to fail with
the messages like below:
sh-pfc e6060000.pfc: cannot locate data/mark enum_id for mark 1989
sh-sci e62c8000.serial: Error applying setting, reverse things back
sh-sci: probe of e62c8000.serial failed with error -22
Add the neceassary PINMUX_IPSR_MSEL() invocations for the HSCK1_E,
HCTS1#_E, and HRTS1#_E signals...
Fixes: 5088451962 ("pinctrl: sh-pfc: r8a7791 PFC support")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add pins, groups, and a function for SCIF_CLK on R-Car H3 ES2.0.
SCIF_CLK is the external clock source for the Baud Rate Generator for
External Clock (BRG) on (H)SCIF serial ports.
Extracted from a big patch in the BSP by Takeshi Kihara.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Add pins, groups, and functions for all SCIF serial ports on R-Car H3
ES2.0.
Extracted from a big patch in the BSP by Takeshi Kihara.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Takeshi Kihara <takeshi.kihara.df@renesas.com>
The Pin Function Controller module in the R-Car H3 ES2.0 differs from
ES1.x in many ways.
The goal is twofold:
1. Support both the ES1.x and ES2.0 SoC revisions in a single binary
for now,
2. Make it clear which code supports ES1.x, so it can easily be
identified and removed later, when production SoCs are deemed
ubiquitous.
Hence this patch:
1. Extracts the support for R-Car H3 ES1.x into a separate file, as
the differences are quite large,
2. Adds code for detecting the SoC revision at runtime using the new
soc_device_match() API, and selecting pinctrl tables for the actual
SoC revision,
3. Replaces the core register and bitfield definitions by their
counterparts for R-Car H3 ES2.0.
The addition of pins, groups, and functions for the various on-chip
devices is left to subsequent patches.
The R-Car H3 ES2.0 register and bitfield definitions were extracted from
a patch in the BSP by Takeshi Kihara.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Takeshi Kihara <takeshi.kihara.df@renesas.com>
When trying to add a gpio-hog, we enter a weird loop where the gpio-ranges
is needed when gpiochip_add_data() is called but in the current implementation
the ranges are added from the driver afterwards.
A simple solution is to rely on the DR gpio-ranges attribute and remove the
call to gpiochip_add_pin_range().
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix some inverted bit numbers in some pinctrl groups and add missing pins
and groups to be in pair with the GXBB pinctrl pins definition.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
With real-time preemption, regmap functions cannot be used in the
implementation of irq_chip since they use spinlocks which may sleep.
Move the setting of the mux for IRQs to an irq_bus_sync_unlock handler
where we are allowed to sleep.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We need to avoid calling regmap functions from irq handlers, so the next
commit is going to move the call to rockchip_set_mux() into an
irq_bus_sync_unlock handler. But we can't return an error from there so
we still need to check the settings from rockchip_irq_set_type() and we
will use this new rockchip_verify_mux() function from there.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This lock is used from rockchip_irq_set_type() which is part of the
irq_chip implementation and thus must use raw_spinlock_t as documented
in Documentation/gpio/driver.txt.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
regmap_update_bits does its own locking and everything else accessed
here is a local variable so there is no need to lock around it.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch fix some spelling typos found in printk.
[jkosina@suse.cz: drop arch/arm64/kernel/hibernate.c that was already
in place]
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Use devm_gpiochip_add_data to simplify the error path in
samsung_gpiolib_register.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
If we request a GPIO hog, then gpiochip_add_data will attempt
to request some of its own GPIOs. The driver also uses
gpiochip_generic_request which means that for any GPIO request to
succeed the pinctrl needs to be registered. Currently however the
driver registers the GPIO and then the pinctrl meaning all GPIO hog
requests will fail, which then in turn causes the whole driver to fail
probe.
Fix this up by ensuring we register the pinctrl first. This
does require us to manually set the GPIO base for the
pinctrl. Fortunately the driver already assigns a fixed GPIO base, in
samsung_gpiolib_register, and uses the same calculation it does for
the pin_base. Meaning the two will always be the same and allowing us
to reuse the pinbase and avoid the issue.
Although currently there are no users of GPIO hogs in mainline
there are plenty of Samsung based boards that are widely used for
development purposes of other hardware. Indeed we hit this issue
whilst attaching some additional hardware to an Arndale system.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
This patch adds support for retention control for Exynos5433 SoCs. Three
groups of pins has been defined for retention control: common shared group
for ALIVE, CPIF, eSE, FINGER, IMEM, NFC, PERIC, TOUCH pin banks and
separate control for FSYS and AUD pin banks, for which PMU retention
registers match whole banks.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
When pin controller device is a part of power domain, there is no guarantee
that the power domain was not turned off and then on during boot process
before probing of the pin control driver. If it happened, then pin control
driver should ensure that pad retention is turned off during its probe call.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
On some Cherry Trail devices the ASL uses the GMMR GPIO to access
GPIOs so as to serialize MMIO accesses to GPIO registers with the
OS, because:
"Due to a silicon issue, a shared lock must be used to prevent concurrent
accesses across the 4 GPIO controllers.
See Intel Atom Z8000 Processor Series Specification Update (Rev. 005),
errata #CHT34, for further information."
This commit adds support for this opregion, this fixes a number of
ASL errors on my Ezpad mini3 tablet and makes the otg port device/host
muxing which is controlled in firmware on this model work properly.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Rockchip finally named the SOC as RV1108, so change it.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
[adapted rk1108 dtsi to keep bisectability]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds the missing PINGROUP for GPIO70-99.
This fixes a crash that happens in pinctrl-msm, if any
of the GPIO70-99 are accessed.
Fixes: 5303f7827f ("pinctrl: qcom: ipq4019: set ngpios to correct value")
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When using GPIO as IRQ source, the GPIO must be configured
in INPUT. Callbacks dedicated for this was missing in
pinctrl-st driver.
This fix the following kernel error when trying to lock a gpio
as IRQ:
[ 7.521095] gpio gpiochip7: (PIO11): gpiochip_lock_as_irq: tried to flag a GPIO set as output for IRQ
[ 7.526018] gpio gpiochip7: (PIO11): unable to lock HW IRQ 6 for IRQ
[ 7.529405] genirq: Failed to request resources for 0-0053 (irq 81) on irqchip GPIO
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Clearing the status bit on irq_unmask will discard any pending interrupt
that did arrive after the irq_ack, i.e. while the IRQ handler function
was executing.
Fixes: f365be0925 ("pinctrl: Add Qualcomm TLMM driver")
Cc: stable@vger.kernel.org
Cc: Stephen Boyd <sboyd@codeaurora.org>
Reported-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some pinctrls share memory regions, and devm_ioremap_resource does not
allow to share resources, in opposition to devm_ioremap.
This patch restores back usage of devm_ioremap function, but with proper
error handling and logging.
Fixes: baafaca ("pinctrl: samsung: Fix return value check in samsung_pinctrl_get_soc_data()")
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As the IODelay driver is a hardware feature of the DRA7xxx SoC
depend on that SoC and compile test.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currently we are trying to enable/disable the clk of irq's gpio bank when
unmask/mask irq. But the kernel's "lazy disable approach" will skip masking
irq when the irq chip doesn't support irq_disable ops.
So we may hit this case:
irq_enable-> enable clk
irq_disable-> noop
irq_enable-> enable clk again
irq_disable-> noop
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
At first these drivers were written as tristate, but the module
usecases are actually not tested. Make all of them boolean.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since commit 3e030b0b4e ("pinctrl: uniphier: allow to have pinctrl
node under syscon node"), this driver has kept compatibility for the
old DT files. Several releases have passed since then, so remove
the obsoleted compatibles and clean up the code.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds support for the missing PWM pins on Meson GXL SoCs, namely:
- PWM_A
- PWM_B
- PWM_C
- PWM_F (GPIOX_7 and GPIOCLK_1 can be selected as output)
- PWM_AO_A (GPIOAO_3 and GPIOAO_8 can be selected as output)
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Update the sh_pfc_soc_info pointer after calling the SoC-specific
initialization function, as it may have been updated to e.g. handle
different SoC revisions. This makes sure the correct subdriver name is
printed later.
Fixes: 0c151062f3 ("sh-pfc: Add support for SoC-specific initialization")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Somehow the QSPI and SCIF_CLK fragments were inserted at the wrong
positions. Restore sort order (alphabetically, per group).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The sunxi pinctrl driver currently implement an irq_chip for handling
interrupts; due to how irq_chip handling is done, it's necessary for the
irq_chip methods to be invoked from hardirq context, even on a a
real-time kernel. Because the spinlock_t type becomes a "sleeping"
spinlock w/ RT kernels, it is not suitable to be used with irq_chips.
A quick audit of the operations under the lock reveal that they do only
minimal, bounded work, and are therefore safe to do under a raw spinlock.
Signed-off-by: Julia Cartwright <julia@ni.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The sirf atlas7 pinctrl drivers currently implement an irq_chip for
handling interrupts; due to how irq_chip handling is done, it's
necessary for the irq_chip methods to be invoked from hardirq context,
even on a a real-time kernel. Because the spinlock_t type becomes a
"sleeping" spinlock w/ RT kernels, it is not suitable to be used with
irq_chips.
A quick audit of the operations under the lock reveal that they do only
minimal, bounded work, and are therefore safe to do under a raw spinlock.
Signed-off-by: Julia Cartwright <julia@ni.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The amd pinctrl drivers currently implement an irq_chip for handling
interrupts; due to how irq_chip handling is done, it's necessary for the
irq_chip methods to be invoked from hardirq context, even on a a
real-time kernel. Because the spinlock_t type becomes a "sleeping"
spinlock w/ RT kernels, it is not suitable to be used with irq_chips.
A quick audit of the operations under the lock reveal that they do only
minimal, bounded work, and are therefore safe to do under a raw spinlock.
Signed-off-by: Julia Cartwright <julia@ni.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The bcm pinctrl drivers currently implement an irq_chip for handling
interrupts; due to how irq_chip handling is done, it's necessary for the
irq_chip methods to be invoked from hardirq context, even on a a
real-time kernel. Because the spinlock_t type becomes a "sleeping"
spinlock w/ RT kernels, it is not suitable to be used with irq_chips.
A quick audit of the operations under the lock reveal that they do only
minimal, bounded work, and are therefore safe to do under a raw spinlock.
Signed-off-by: Julia Cartwright <julia@ni.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The sysfs and debugfs entries for pin control drivers work better when
the individual pins are given real names, even if they are all just
"gpio0", "gpio1", etc.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
To prevent external signal crosstalk, some pins need to
enable input schmitt, like i2c pins, 32k-input pin and so on.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Allwinner pin controllers are also GPIO controllers.
Currently, if GPIOLIB is forgot to be chosen, the build of
pinctrl-sunxi.c will fail for lacking a lot of gpiochip_* functions.
Select GPIOLIB to ensure this driver can be built.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The A64 has a R_PIO pin controller, similar to the one found on the H3 SoC.
Add support for the pins controlled by the R_PIO controller.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
ARM64 Allwinner SoCs used to have every pinctrl driver selected in
ARCH_SUNXI. Change this to make their default value to (ARM64 &&
ARCH_SUNXI).
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Just fix spelling typos in comments.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Port D and port E GPIO loopback modes are commonly enabled via hardware
straps for use with front-panel buttons. When the BMC is powered
off or fails to boot, the front-panel buttons are directly connected to
the host chipset via the loopback to allow direct power-on and reset
control. Once the BMC has booted, the loopback mode must be disabled for
the BMC to take over control of host power-on and reset.
Disabling these loopback modes requires writing to the hardware strap
register which violates the current design of assuming the system
designer chose the strap settings for a specific reason and they should
be treated as read-only. Only the two bits of the strap register related
to these loopback modes are allowed to be written and comments have been
added to explain why.
Signed-off-by: Rick Altherr <raltherr@google.com>
Acked-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Note, the iomux of following pins are special, need to
be recalculated specially.
- gpio2_b4
- gpio2_b7
- gpio2_c7
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some pins are special at a bank so that add
IOMUX_RECALCED type to indicate which iomux source
of the bank need to be recalculated. If the mux
recalculateed callback and IOMUX_RECALCED type
were set, recalculate the pins' iomux by using
mux recalculated data struct.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The local variable drvdata is not used in samsung_gpio_set_direction.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch changes pin names of AIO and XIRQ according to updated
specification.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The get_direction callback function allows gpiolib to know the current
direction (input vs output) for a given GPIO.
This is particularly useful on ACPI systems, where the GPIOs are
configured only by firmware (typically UEFI), so the only way to
know the initial values to query the hardware directly. Without
this function, gpiolib thinks that all GPIOs are configured for
input.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix typos and add the following to the scripts/spelling.txt:
overrided||overridden
Link: http://lkml.kernel.org/r/1481573103-11329-22-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Core changes:
- Switch the generic pin config argument from 16 to 24 bits,
only use 8 bits for the configuration type. We might need to
encode more information about a certain setting than we need
to encode different generic settings.
- Add a cross-talk API to the pin control GPIO back-end,
utilizing pinctrl_gpio_set_config() from GPIO drivers that
want to set up a certain pin configuration in the back-end.
This also includes the .set_config() refactoring of the
GPIO chips, so that they pass a generic configuration for
things like debouncing and single ended (typically open
drain). This change has also been merged in an immutable
branch to the GPIO tree.
- Take hogs with a delayed work, so that we finalize probing
a pin controller before trying to get any hogs.
- For pin controllers putting all group and function definitions
into the device tree, we now have generic code to deal with
this and it is used in two drivers so far.
- Simplifications of the pin request conflict check.
- Make dt_free_map() optional.
Updates to drivers:
- pinctrl-single now use the generic helpers to generate dynamic
group and function tables from the device tree.
- Texas Instruments IOdelay configuration driver add-on to
pinctrl-single.
- i.MX: use radix trees to store groups and functions, use the new
generic group and function helpers to manage them.
- Intel: add support for hardware debouncing and 1K pull-down.
New subdriver for the Gemini Lake SoC.
- Renesas SH-PFC: drive strength and bias support, CAN bus muxing,
MSIOF, SDHI, HSCIF for r8a7796. Gyro-ADC supporton r8a7791.
- Aspeed: use syscon cross-dependencies to set up related bits in
the LPC host controller and display controller.
- Aspeed: finalize G4 and G5 support. Fix mux configuration on
GPIOs. Add banks Y, Z, AA, AB and AC.
- AMD: support additional GPIO.
- STM32: set this controller to strict muxing mode.
STM32H743 MCU support.
- Allwinner sunxi: deep simplifications on how to support
subvariants of SoCs without adding to much SoC-specific data
for each subvariant, especially for sun5i variants. New driver
for V3s SoCs. New driver for the H5 SoC. Support A31/A31s
variants with the new variant framework.
- Mvebu: simplifications to use a MMIO and regmap abstraction.
New subdrivers for the 98DX3236, 98DX5241 SoCs.
- Samsung Exynos: delete Exynos4415 support. Add crosstalk to the
SoC driver to access regmaps. Add infrastructure for pin-bank
retention control. Clean out the pin retention control from
arch/arm/mach-exynos and arch/arm/mach-s5p and put it properly
in the Samsung pin control driver(s).
- Meson: add HDMI HPD/DDC pins. Add pwm_ao_b pin.
- Qualcomm: use raw spinlock variants: this makes the qualcomm
driver realtime-safe.
-----BEGIN PGP SIGNATURE-----
iQIcBAABAgAGBQJYq/7kAAoJEEEQszewGV1zf4oQALVaN5tuaCbzN4QOq87jzXmk
K195kKG0nkNvN6o5llNhBszHfCSmX1+oSscxuCF/88kH4mFHeDIbvg0KOk5IZYxA
YlT8NA75C9+flARE3gQUyL320ulahWbvOthntQprzsVU4RJa0zP38peQsfiUd8W1
ch8GInJYYkczcsAbmziyUOBu5a2o9tX3u8BF8FaBf2uyrCiBC/ZT2VpzvbOR5NeU
MvjFvc7bq2fNltzDNHdZZUo/5iCbnPlRNig2umDp5fFa8rZcdPmGMAOl4p6nizHY
S16xDl38xxDQx8sp1IH4n+th3G2cXoONEj9eZ6woWTJhLbLc13CacYPfleYfqEOe
+JyrUgBgFBINiFWDHHaebWJeD2M/QF4FnSDGnnJBy/bKWe6lJnknGvSZNcIEvdvB
QeeKyfrvnKiCyjNY4N+ZNdMLA2vj5o86vG2hSqztPiwYWDePbN76yeZ7l79bFfOo
ZnCa2ay70Np7xwrQWors4Gl2LV2zJG7AkaNA7vvS9NX6OURu/SkNVePkY1XHCLwu
lNvYd4iwFJxzXm08TsgtLC080eZfvCot9xqbgzvoapnwx7tBuaAakXI4bh0T3x4n
pEauKO3oNE/K89mN9QK2jfsD9kDWvm4xvc+ilA6DGU0C37XnDQjF+Q5xy16262Gh
9w0yWMlqzrr7stUXAjS4
=IMY0
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"Pin control bulk changes for the v4.11 kernel cycle.
Core changes:
- Switch the generic pin config argument from 16 to 24 bits, only use
8 bits for the configuration type. We might need to encode more
information about a certain setting than we need to encode
different generic settings.
- Add a cross-talk API to the pin control GPIO back-end, utilizing
pinctrl_gpio_set_config() from GPIO drivers that want to set up a
certain pin configuration in the back-end.
This also includes the .set_config() refactoring of the GPIO chips,
so that they pass a generic configuration for things like
debouncing and single ended (typically open drain). This change has
also been merged in an immutable branch to the GPIO tree.
- Take hogs with a delayed work, so that we finalize probing a pin
controller before trying to get any hogs.
- For pin controllers putting all group and function definitions into
the device tree, we now have generic code to deal with this and it
is used in two drivers so far.
- Simplifications of the pin request conflict check.
- Make dt_free_map() optional.
Updates to drivers:
- pinctrl-single now use the generic helpers to generate dynamic
group and function tables from the device tree.
- Texas Instruments IOdelay configuration driver add-on to
pinctrl-single.
- i.MX: use radix trees to store groups and functions, use the new
generic group and function helpers to manage them.
- Intel: add support for hardware debouncing and 1K pull-down. New
subdriver for the Gemini Lake SoC.
- Renesas SH-PFC: drive strength and bias support, CAN bus muxing,
MSIOF, SDHI, HSCIF for r8a7796. Gyro-ADC supporton r8a7791.
- Aspeed: use syscon cross-dependencies to set up related bits in the
LPC host controller and display controller.
- Aspeed: finalize G4 and G5 support. Fix mux configuration on GPIOs.
Add banks Y, Z, AA, AB and AC.
- AMD: support additional GPIO.
- STM32: set this controller to strict muxing mode. STM32H743 MCU
support.
- Allwinner sunxi: deep simplifications on how to support subvariants
of SoCs without adding to much SoC-specific data for each
subvariant, especially for sun5i variants. New driver for V3s SoCs.
New driver for the H5 SoC. Support A31/A31s variants with the new
variant framework.
- Mvebu: simplifications to use a MMIO and regmap abstraction. New
subdrivers for the 98DX3236, 98DX5241 SoCs.
- Samsung Exynos: delete Exynos4415 support. Add crosstalk to the SoC
driver to access regmaps. Add infrastructure for pin-bank retention
control. Clean out the pin retention control from
arch/arm/mach-exynos and arch/arm/mach-s5p and put it properly in
the Samsung pin control driver(s).
- Meson: add HDMI HPD/DDC pins. Add pwm_ao_b pin.
- Qualcomm: use raw spinlock variants: this makes the qualcomm driver
realtime-safe"
* tag 'pinctrl-v4.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (111 commits)
pinctrl: samsung: Fix return value check in samsung_pinctrl_get_soc_data()
pinctrl: intel: unlock on error in intel_config_set_pull()
pinctrl: berlin: make bool drivers explicitly non-modular
pinctrl: spear: make bool drivers explicitly non-modular
pinctrl: mvebu: make bool drivers explicitly non-modular
pinctrl: sunxi: make sun5i explicitly non-modular
pinctrl: sunxi: Remove stray printk call in sun5i driver's probe function
pinctrl: samsung: mark PM functions as __maybe_unused
pinctrl: sunxi: Remove redundant A31s pinctrl driver
pinctrl: sunxi: Support A31/A31s with pinctrl variants
pinctrl: Amend bindings for STM32 pinctrl
pinctrl: Add STM32 pinctrl driver DT bindings
pinctrl: stm32: Add STM32H743 MCU support
include: dt-bindings: Add STM32H7 pinctrl DT defines
gpio: aspeed: Remove dependence on GPIOF_* macros
pinctrl: stm32: fix bad location of gpiochip_lock_as_irq
drivers: pinctrl: add driver for Allwinner H5 SoC
pinctrl: intel: Add Intel Gemini Lake pin controller support
pinctrl: intel: Add support for 1k additional pull-down
pinctrl: intel: Add support for hardware debouncer
...
In case of error, the function devm_ioremap() returns NULL pointer not
ERR_PTR(). Fix by using devm_ioremap_resource instead of devm_ioremap.
Fixes: 8b1bd11c1f ("pinctrl: samsung: Add the support the multiple IORESOURCE_MEM for one pin-bank")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We need to unlock before returning -EINVAL on this error path.
Fixes: 04cc058f0c ("pinctrl: intel: Add support for 1k additional pull-down")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
None of the Kconfigs for any of these drivers are tristate,
meaning that they currently are not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Since module_platform_driver() uses the same init level priority as
builtin_platform_driver() the init ordering remains unchanged with
this commit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Cc: "Antoine Ténart" <antoine.tenart@free-electrons.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Cc: Hongzhou Yang <hongzhou.yang@mediatek.com>
Cc: Thomas Hebb <tommyhebb@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
None of the Kconfigs for any of these drivers are tristate,
meaning that they currently are not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the drivers there is no doubt they are builtin-only. All
drivers get the exact same change, so they are handled in batch.
Changes are (1) use init.h header in place of module.h header,
(2) delete module_exit related code, (3) delete MODULE_DEVICE_TABLE,
and (4) delete MODULE_LICENCE/MODULE_AUTHOR and associated tags.
None of these drivers were using module_init() so we don't have to
worry about the init ordering getting changed with this commit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE etc. tags since all that information
is already contained at the top of each file in the comments.
Cc: spear-devel@list.st.com
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
None of the Kconfigs for any of these drivers are tristate, meaning
that they currently are not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the drivers there is no doubt they are builtin-only.
All drivers get the exact same change, so they are handled in batch.
Changes are (1) use builtin_platform_driver, (2) dont use module.h
(3) delete module_exit related code, (4) delete MODULE_DEVICE_TABLE,
and (5) delete MODULE_LICENCE/MODULE_AUTHOR and associated tags.
For the dove driver we explicitly disallow a driver unbind, since
that doesn't have a sensible use case anyway, and it allows us to
drop the ".remove" code for non-modular drivers.
Since module_platform_driver() uses the same init level priority as
builtin_platform_driver() the init ordering remains unchanged with
this commit.
We deleted the MODULE_LICENSE etc. tags since all that information
is already contained at the top of the file in the comments.
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We had all these corrected in commit 0c8c6ba00c ("pinctrl: sunxi:
make bool drivers explicitly non-modular") but this new one recently
crept in.
The Kconfig currently controlling compilation of this code is:
drivers/pinctrl/sunxi/Kconfig:config PINCTRL_SUN5I
drivers/pinctrl/sunxi/Kconfig: def_bool MACH_SUN5I
...meaning that it currently is not being built as a module by anyone.
Lets remove the couple traces of modular infrastructure use, so that
when reading the driver there is no doubt it is builtin-only.
Since module_platform_driver() uses the same init level priority as
builtin_platform_driver() the init ordering remains unchanged with
this commit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There is a stray printk call in the new sun5i pinctrl driver's probe
function.
Remove it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The rework of the suspend/resume handling uses the wrong #ifdef check, leading
to a build warning without CONFIG_PM_SLEEP:
drivers/pinctrl/samsung/pinctrl-samsung.c:1142:12: error: 'samsung_pinctrl_resume' defined but not used [-Werror=unused-function]
drivers/pinctrl/samsung/pinctrl-samsung.c:1092:12: error: 'samsung_pinctrl_suspend' defined but not used [-Werror=unused-function]
Using a __maybe_unused annotation instead of the #ifdef is a simple way to
avoid this problem class.
Fixes: 2b24efa8e5 ("pinctrl: samsung: Replace syscore ops with standard platform device pm_ops")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Now that we can support the A31s pin controller with the A31 driver
using the new variants support, the independent A31s driver becomes
redundant.
Remove it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The A31s is a trimmed down version of the A31. Some hardware blocks
are removed, thus not available for muxing on the external pins.
Some external pins were directly removed.
This makes it easy to support the A31s pin controller with the A31
driver. We just mark the pins and functions that were trimmed as
A31 only.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Move gpio lock as irq from "domain alloc" callback to "domain activate"
callback. It will allow to use gpiolib sysfs correctly.
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Based on the Allwinner H5 datasheet and the pinctrl driver of the
backward-compatible H3 this introduces the pin multiplex assignments for
the H5 SoC.
H5 introduced some more pin functions (e.g. three more groups of TS
pins, and one more groups of SIM pins) than H3.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
According to VLI64 Intel Atom E3800 Specification Update (#329901)
concurrent read accesses may result in returning 0xffffffff and write
accesses may be dropped silently.
To workaround all accesses must be protected by locks.
Cc: stable@vger.kernel.org
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Debounce value is set globally per community. Otherwise user will easily
get a kernel crash when they start using the feature:
BUG: unable to handle kernel paging request at ffffc900003be000
IP: byt_gpio_dbg_show+0xa9/0x430
Make it clear in byt_gpio_reg().
Note that this fix just prevents kernel to crash, but doesn't make any
difference to the existing logic. It means the last caller will win the
trade and debounce value will be configured accordingly. The actual
logic fix needs to be thought about and it's not as important as crash
fix. That's why the latter goes separately and right now.
Fixes: 658b476c74 ("pinctrl: baytrail: Add debounce configuration")
Cc: Cristina Ciocan <cristina.ciocan@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The commit 04ff5a095d ("pinctrl: baytrail: Rectify debounce support")
almost fixes the logic of debuonce but missed couple of things, i.e.
typo in mask when disabling debounce and lack of enabling it back.
This patch addresses above issues.
Reported-by: Jean Delvare <jdelvare@suse.de>
Fixes: 04ff5a095d ("pinctrl: baytrail: Rectify debounce support")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This driver adds pinctrl/GPIO support for Intel Gemini Lake SoC. The
GPIO controller is based on the next generation GPIO hardware but still
compatible with the one supported by the Intel core pinctrl/GPIO driver.
This commit includes material from David E. Box.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The next generation Intel GPIO hardware supports additional 1k pull-down
per-pad. Add support for this to the Intel core pinctrl driver.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The next generation Intel GPIO hardware has two additional registers
PADCFG2 and PADCFG3. The latter is marked as reserved but the former
includes configuration for per-pad hardware debouncer.
This patch adds support for that in the Intel pinctrl core driver. Since
these are additional features on top of the current generation hardware,
we use revision number and feature flags to enable this if detected.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This pinctrl driver supports the 98DX3236, 98DX3336 and 98DX4251 SoCs
from Marvell.
Signed-off-by: Kalyan Kinthada <kalyan.kinthada@alliedtelesis.co.nz>
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There is no need to take pointer of a pointer to an array of SoC data in
platform driver.
Do it in the same way as it's done for ACPI.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Not every pin can be configured. Add missed check to prevent access
violation.
Fixes: 4e80c8f505 ("pinctrl: intel: Add Intel Merrifield pin controller support")
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit 07fe64ba21 ("pinctrl: sunxi: Handle bias disable") actually
enforced enforced the disabling of the pull up/down resistors instead of
ignoring it like it was done before.
This was part of a wider rework to switch to the generic pinconf bindings,
and was meant to be merged together with DT patches that were switching to
it, and removing what was considered default values by both the binding and
the boards. This included no bias on a pin.
However, those DT patches were delayed to 4.11, which would be fine only
for a significant number boards having the bias setup wrong, which in turns
break the MMC on those boards (and possibly other devices too).
In order to avoid conflicts as much as possible, bring back the old
behaviour for 4.10, and we'll revert that commit once all the DT bits will
have landed.
Tested-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Once the dependency on PMU driver (for pad retention control) has been
removed, there is no reason to use syscore_ops based suspend/resume.
This patch replaces it with standard platform device pm_ops based solution.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch moves pad retention control from S5PV210 machine code to
Exynos pin controller driver. This helps to avoid possible ordering
and logical dependencies between machine and pin control code. Till
now it worked fine only because sys_ops for machine code and pin
controller were called in registration order.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
For mach-s5pv210:
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch moves pad retention control from PMU driver to Exynos pin
controller driver. This helps to avoid possible ordering and logical
dependencies between machine, PMU and pin control code. Till now it
worked fine only because sys_ops for PMU and pin controller were called
in registration order.
This is also a preparation for adding new features to Exynos pin
controller driver, like runtime power management and suspending
individual pin controllers, which might be a part of some power domain.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Apparently each GPIO pad's register are 16 bytes, so multiply the pad_map
by that. The same is done in byt_gpio_reg the only other place where
pad_map is used.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Pad retention control after suspend/resume cycle should be done from pin
controller driver instead of PMU (power management unit) driver to avoid
possible ordering and logical dependencies. Till now it worked fine only
because PMU driver registered its sys_ops after pin controller.
This patch adds infrastructure to handle pad retention during pin control
driver resume.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
'enable' parameter has been removed a while ago, so all code for handling
it can be simply removed.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Exynos5433 support has been added in parallel to adding initconst
annotation to most of the init data structures, so add those
annotations also to Exynos5433 structures.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Do not hide pinctrl drivers for Mediatek platforms using
conditionals. Doing so actually leaves the symbols present (but
always disabled) on all other platforms, which is confusing and
inefficient. Better use real dependencies so that the symbols do not
exist at all on platforms where they are not relevant.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Reported-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds support for the pwm_ao_b pin. Unfortunately the registers for
the pwm_ao pins are not documented at all. The source for the pwm_ao_b
pin from this patch is the Khadas VIM GPL kernel source, which sets bit
3 and unsets bits 4 and 31 to enable the PWM LEDs.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
While we have no users yet rename the platform driver to use the same
pattern as the rest of Intel SoCs, i.e. use full SoC name in
'apollolake-pinctrl'.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currently we already have two pin configuration related callbacks
available for GPIO chips .set_single_ended() and .set_debounce(). In
future we expect to have even more, which does not scale well if we need
to add yet another callback to the GPIO chip structure for each possible
configuration parameter.
Better solution is to reuse what we already have available in the
generic pinconf.
To support this, we introduce a new .set_config() callback for GPIO
chips. The callback takes a single packed pin configuration value as
parameter. This can then be extended easily beyond what is currently
supported by just adding new types to the generic pinconf enum.
If the GPIO driver is backed up by a pinctrl driver the GPIO driver can
just assign gpiochip_generic_config() (introduced in this patch) to
.set_config and that will take care configuration requests are directed
to the pinctrl driver.
We then convert the existing drivers over .set_config() and finally
remove the .set_single_ended() and .set_debounce() callbacks.
Suggested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When a GPIO driver is backed by a pinctrl driver the GPIO driver
sometimes needs to call the pinctrl driver to configure certain things,
like whether the pin is used as input or output. In addition to this
there are other configurations applicable to GPIOs such as setting
debounce time of the GPIO.
To support this we introduce a new function pinctrl_gpio_set_config()
that can be used by gpiolib based driver to pass configuration requests
to the backing pinctrl driver.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The current pinconf packed format allows only 16-bit argument limiting
the maximum value 65535. For most types this is enough. However,
debounce time can be in range of hundreths of milliseconds in case of
mechanical switches so we cannot represent the worst case using the
current format.
In order to support larger values change the packed format so that the
lower 8 bits are used as type which leaves 24 bits for the argument.
This allows representing values up to 16777215 and debounce times up to
16 seconds.
We also convert the existing users to use 32-bit integer when extracting
argument from the packed configuration value.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
A cleanup caused a harmless warning:
drivers/pinctrl/mvebu/pinctrl-kirkwood.c: In function 'kirkwood_pinctrl_probe':
drivers/pinctrl/mvebu/pinctrl-kirkwood.c:460:19: error: unused variable 'res' [-Werror=unused-variable]
The obvious fix is to remove the declaration of the now unused
variable.
Fixes: ad9ec4ecee ("pinctrl: mvebu: switch drivers to generic simple mmio")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Incorrect video output configuration bits were being tested on pins in
GPIO banks AA and AB for the ROM{8,16} mux functions. The ROM{8,16}
functions are the highest priority for the relevant pins and also the
default function, so we require the relevant video output configuration
be disabled to mux GPIO functionality. As the wrong bits were being
tested a GPIO export would succeed but leave the pin in an unresponsive
state (i.e. value updates were ignored).
This misbehaviour was discovered as part of extending the GPIO
controller's support to cover banks Y, Z, AA, AB and AC (AC in the case
of the g5 SoC).
Fixes: 6d329f14a7 ("pinctrl: aspeed-g4: Add mux configuration for all pins")
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The MSM pinctrl driver currently implements an irq_chip for handling
GPIO interrupts; due to how irq_chip handling is done, it's necessary
for the irq_chip methods to be invoked from hardirq context, even on a
a real-time kernel. Because the spinlock_t type becomes a "sleeping"
spinlock w/ RT kernels, it is not suitable to be used with irq_chips.
A quick audit of the operations under the lock reveal that they do only
minimal, bounded work, and are therefore safe to do under a raw
spinlock.
On real-time kernels, this fixes an OOPs which looks like the following,
as reported by Brian Wrenn:
kernel BUG at kernel/locking/rtmutex.c:1014!
Internal error: Oops - BUG: 0 [#1] PREEMPT SMP
Modules linked in: spidev_irq(O) smsc75xx wcn36xx [last unloaded: spidev]
CPU: 0 PID: 1163 Comm: irq/144-mmc0 Tainted: G W O 4.4.9-linaro-lt-qcom #1
PC is at rt_spin_lock_slowlock+0x80/0x2d8
LR is at rt_spin_lock_slowlock+0x68/0x2d8
[..]
Call trace:
rt_spin_lock_slowlock
rt_spin_lock
msm_gpio_irq_ack
handle_edge_irq
generic_handle_irq
msm_gpio_irq_handler
generic_handle_irq
__handle_domain_irq
gic_handle_irq
Reported-by: Brian Wrenn <dcbrianw@gmail.com>
Tested-by: Brian Wrenn <dcbrianw@gmail.com>
Signed-off-by: Julia Cartwright <julia@ni.com>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Return proper error code in case of memory allocation failure.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Memory subsystem already prints message about failed memory
allocation, there is no need to do it in the drivers.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add pin configuration support for Gyro-ADC, named ADI on r8a7791 SoC.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Tested-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The GXBB and GXL/GXM pinctrl drivers had a configuration which conflicts
with uart_ao_a. According to the GXBB ("S905") datasheet the AO UART
functions are:
- GPIOAO_0: Func1 = UART_TX_AO_A (bit 12), Func2 = UART_TX_AO_B (bit 26)
- GPIOAO_1: Func1 = UART_RX_AO_A (bit 11), Func2 = UART_RX_AO_B (bit 25)
- GPIOAO_4: Func2 = UART_TX_AO_B (bit 24)
- GPIOAO_5: Func2 = UART_RX_AO_B (bit 25)
The existing definition for uart_AO_A already uses GPIOAO_0 and GPIOAO_1.
The old definition of uart_AO_B however was broken, as it used GPIOAO_0
for TX (which would be fine) and two pins (GPIOAO_1 and GPIOAO_5) for RX
(which does not make any sense).
This fixes the uart_AO_B configuration by moving it to GPIOAO_4 and
GPIOAO_5 (it would be possible to use GPIOAO_0 and GPIOAO_1 in theory,
but all existing hardware uses uart_AO_A there).
The fix for GXBB and GXL/GXM is identical since it seems that these
specific pins are identical on both SoC variants.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It's not necessary to unregister pin controller device registered
with devm_pinctrl_register() and using pinctrl_unregister() leads
to a double free.
Fixes: 3bfd44306c ("pinctrl: amd: Add support for additional GPIO")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add pinctrl functions for HDMI HPD pin and DDC pins on Amlogic Meson
GXL and GXBB SoCs.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Support for Exynos4415 is going away because there are no internal nor
external users.
Since commit 46dcf0ff0d ("ARM: dts: exynos: Remove exynos4415.dtsi"),
the platform cannot be instantiated so remove also the drivers.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
pin is an unsigned int and therefore can never be < 0 so
this check is redundant. Remove the check and the associated
dev_err error message.
Fixes CoverityScan CID#1396438 ("Unsigned compared against 0")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add a simple regmap based pinctrl implementation for mvebu, for syscon
based regmap drivers.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Move the mvebu pinctrl drivers over to the generic simple mmio
implementation, saving a substantial number of lines of code in
the process.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Provide a generic simple mmio-based probe function and methods, which
pinctrl drivers can use to initialise the mvebu pinctrl subsystem.
Most mvebu pinctrl drivers can use this.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Provide per-control private data into each mvebu pinctrl method, which
will allow us to provide some completely generic helpers without the
global variable and per-instance function definitions that would be
required when we have multiple pin controllers on a SoC.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As the mvebu_mpp_ctrl structures contain function pointers, it is
preferable for these to be made read-only to prevent the function
pointers being modified. So make these const.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Single characters should be put into a sequence.
Thus use the corresponding function "seq_putc".
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Strings which did not contain data format specifications should be put
into a sequence. Thus use the corresponding function "seq_puts".
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The script "checkpatch.pl" pointed information out like the following.
WARNING: void function return statements are not generally useful
Thus remove such a statement in the affected function.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The script "checkpatch.pl" pointed information out like the following.
WARNING: Possible unnecessary 'out of memory' message
Thus fix the affected source code places.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* A multiplication for the size determination of a memory allocation
indicated that an array data structure should be processed.
Thus use the corresponding function "kmalloc_array".
This issue was detected by using the Coccinelle software.
* Replace the specification of a data structure by a pointer dereference
to make the corresponding size determination a bit safer according to
the Linux coding style convention.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- Add bias handling for non-GPIO pins for R-Car H3,
- Add drive-strength and bias handling for R-Car M3-W,
- Add CAN, CAN FD, MSIOF, and HSCIF pin groups for R-Car M3-W,
- Add SDHI voltage switching for R-Car M2-N.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=12cM
-----END PGP SIGNATURE-----
Merge tag 'sh-pfc-for-v4.11-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into devel
pinctrl: sh-pfc: Updates for v4.11
- Add bias handling for non-GPIO pins for R-Car H3,
- Add drive-strength and bias handling for R-Car M3-W,
- Add CAN, CAN FD, MSIOF, and HSCIF pin groups for R-Car M3-W,
- Add SDHI voltage switching for R-Car M2-N.
The struct pinctrl_dev's node field is not properly set up, which means
the .prev and .next fields will be NULL. That's not something that the
linked list code can deal with, so extra care must be taken when using
these fields. An example of this is introduced in commit 3429fb3cda
("pinctrl: Fix panic when pinctrl devices with hogs are unregistered")
where list_del() is made conditional on the pinctrl device being part
of the pinctrl device list. This is to ensure that list_del() won't
crash upon encountering a NULL pointer in .prev and/or .next.
After initializing the list head there's no need to jump through these
extra hoops and list_del() will work unconditionally. This is because
the initialized list head points to itself and therefore the .prev and
.next fields can be properly dereferenced.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit df61b366af26 ("pinctrl: core: Use delayed work for hogs") caused a
regression at least with sh-pfc that is also a GPIO controller as
noted by Geert Uytterhoeven <geert@linux-m68k.org>.
As the original pinctrl_register() has issues calling pin controller
driver functions early before the controller has finished registering,
we can't just revert commit df61b366af26. That would break the drivers
using GENERIC_PINCTRL_GROUPS or GENERIC_PINMUX_FUNCTIONS.
So let's fix the issue with the following steps as a single patch:
1. Revert the late_init parts of commit df61b366af26.
The late_init clearly won't work and we have to just give up
on fixing pinctrl_register() for GENERIC_PINCTRL_GROUPS and
GENERIC_PINMUX_FUNCTIONS.
2. Split pinctrl_register() into two parts
By splitting pinctrl_register() into pinctrl_init_controller()
and pinctrl_create_and_start() we have better control over when
it's safe to call pinctrl_create().
3. Introduce a new pinctrl_register_and_init() function
As suggested by Linus Walleij <linus.walleij@linaro.org>, we
can just introduce a new function for the controllers that need
pinctrl_create() called later.
4. Convert the four known problem cases to use new function
Let's convert pinctrl-imx, pinctrl-single, sh-pfc and ti-iodelay
to use the new function to fix the issues. The rest of the drivers
can be converted later. Let's also update Documentation/pinctrl.txt
accordingly because of the known issues with pinctrl_register().
Fixes: df61b366af26 ("pinctrl: core: Use delayed work for hogs")
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since gpio_dev->hwbank_num is now a variable, the compiler cannot
figure out if pin_num is initialized at all:
drivers/pinctrl/pinctrl-amd.c: In function 'amd_gpio_dbg_show':
drivers/pinctrl/pinctrl-amd.c:210:3: warning: 'pin_num' may be used uninitialized in this function [-Wmaybe-uninitialized]
for (; i < pin_num; i++) {
^~~
drivers/pinctrl/pinctrl-amd.c:172:21: warning: 'i' may be used uninitialized in this function [-Wmaybe-uninitialized]
This adds a 'default' statement to make that case well-defined.
Fixes: 3bfd44306c ("pinctrl: amd: Add support for additional GPIO")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When DIRECT_IRQ_EN is set, the pin is routed directly to the IO-APIC bypassing
the GPIO driver completely. However, the mask register is still used to
determine if the pin is supposed to generate IRQ or not.
So with commit 3ae02c14d9 the IRQ core masks all IRQs (because of
handle_bad_irq()) the pin connected to the touchscreen gets masked as well and
hence no interrupts.
To make this all work as expected we do not add those GPIOs to the IRQ domain
that can actually propagate interrupts.
Fixes: 3ae02c14d9 ("pinctrl: intel: set default handler to be handle_bad_irq()")
Reported-by: Robert R. Howell <rhowell@uwyo.edu>
Suggested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
V3s SoC features only a pin controller (for the lack of CPUs part).
Add a driver for this controller.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We accidentally deleted two tabs from the first line, but even with that
fixed the conditions were not really kernel style. Put the && at the
end of the line so we can align the condition clauses. Also add spaces
around the "+" operator.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Upon failing kzalloc() will print an error message in the log, so
there's no need for additional printouts. Also standardizes the "!ptr"
vs "ptr == NULL" while I'm touching those lines.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds the pintrol-da850-pupd driver to the module device table so that
udev will automatically bind the driver to the device.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This simplifies error handling and allows us to drop error path handlers
completely.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The commit 658b476c74 ("pinctrl: baytrail: Add debounce configuration")
implements debounce for Baytrail pin control, but seems wasn't tested properly.
The register which keeps debounce value is separated from the configuration
one. Writing wrong values to the latter will guarantee wrong behaviour of the
driver and even might break something physically.
Besides above there is missed case how to disable it, which is actually done
through the bit in configuration register.
Rectify implementation here by using proper register for debounce value.
Fixes: 658b476c74 ("pinctrl: baytrail: Add debounce configuration")
Cc: Cristina Ciocan <cristina.ciocan@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This simplifies error handling and allows us to drop intel_pinctrl_remove()
completely.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There are two bits in the PADCFG0 register to configure direction, one per
TX/RX buffers.
For now we wrongly assume that the GPIO is always requested before it is being
used, which is not true when the GPIO is used through irqchip. In this case the
GPIO is never requested and we never enable RX buffer for it.
Fix this by setting both bits accordingly.
Reported-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
PADCFGLOCK (and PADCFGLOCK_TX) offset in Broxton actually starts at 0x060
and not 0x090 as used in the driver. Fix it to use the correct offset.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
SoC family such as DRA7 family of processors have, in addition
to the regular muxing of pins (as done by pinctrl-single), a separate
hardware module called IODelay which is also expected to be configured.
The "IODelay" module has it's own register space that is independent
of the control module and the padconf register area.
With recent changes to the pinctrl framework, we can now support
this hardware with a reasonably minimal driver by using #pinctrl-cells,
GENERIC_PINCTRL_GROUPS and GENERIC_PINMUX_FUNCTIONS.
It is advocated strongly in TI's official documentation considering
the existing design of the DRA7 family of processors during mux or
IODelay reconfiguration, there is a potential for a significant glitch
which may cause functional impairment to certain hardware. It is
hence recommended to do as little of muxing as absolutely necessary
without I/O isolation (which can only be done in initial stages of
bootloader).
NOTE: with the system wide I/O isolation scheme present in DRA7 SoC
family, it is not reasonable to do stop all I/O operations for every
such pad configuration scheme. So, we will let it glitch when used in
this mode.
Even with the above limitation, certain functionality such as MMC has
mandatory need for IODelay reconfiguration requirements, depending on
speed of transfer. In these cases, with careful examination of usecase
involved, the expected glitch can be controlled such that it does not
impact functionality.
In short, IODelay module support as a padconf driver being introduced
here is not expected to do SoC wide I/O Isolation and is meant for
a limited subset of IODelay configuration requirements that need to
be dynamic and whose glitchy behavior will not cause functionality
failure for that interface.
IMPORTANT NOTE: we take the approach of keeping LOCK_BITs cleared
to 0x0 at all times, even when configuring Manual IO Timing Modes.
This is done by eliminating the LOCK_BIT=1 setting from Step
of the Manual IO timing Mode configuration procedure. This option
leaves the CFG_* registers unprotected from unintended writes to the
CTRL_CORE_PAD_* registers while Manual IO Timing Modes are configured.
This approach is taken to allow for a generic driver to exist in kernel
world that has to be used carefully in required usecases.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
[tony@atomide.com: updated to use generic pinctrl functions, added
binding documentation, updated comments]
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If the pin controller driver is using devm_kzalloc, there may not be
anything to do for dt_free_map. Let's make it optional to avoid
unncessary boilerplate code.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Now that we have a common pinctrl driver for all the sun5i SoCs, we can
remove the old, separate drivers.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The sun5i SoCs (A10s, A13, GR8) are all based on the same die fit in
different packages. Hence, the pins and functions available are just the
based on the same set, each SoC having a different subset.
Introduce a common pinctrl driver that supports multiple variants to allow
to put as much as we can in common.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some SoCs are either supposed to be pin compatible (A10 and A20 for
example), or are just repackaged versions of the same die (A10s, A13, GR8).
In those case, having a full blown pinctrl driver just introduces
duplication in both data size and maintainance effort.
Add a variant option to both pins and functions to be able to limit the
pins and functions described only to a subset of the SoC we support with a
given driver.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit df61b366af26 ('pinctrl: core: Use delayed work for hogs')
deferred part of the registration for pinctrl devices if the pinctrl
device has hogs. This introduced a window where if the pinctrl device
with hogs was sucessfully registered, but then unregistered again
(which could be caused by parent device being probe deferred) before
the delayed work has chanced to run, then this will cause a kernel
panic to occur because:
1. The 'pctldev->p' has not yet been initialised and when unregistering
the pinctrl device we only check to see if it is an error value, but
now it could also be NULL.
2. The pinctrl device may not have been added to the 'pinctrldev_list'
list and we don't check to see if it was added before removing.
Fix up the above by checking to see if the 'pctldev->p' pointer is an
error value or NULL before putting the pinctrl device and verifying
that the pinctrl device is present in 'pinctrldev_list' before removing.
Fixes: df61b366af26 ('pinctrl: core: Use delayed work for hogs')
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
3bfd44306c ("pinctrl: amd: Add support for additional GPIO")
created the following warning:
drivers/pinctrl/pinctrl-amd.c: In function 'amd_gpio_dbg_show':
drivers/pinctrl/pinctrl-amd.c:210:3: warning: 'pin_num' may be used uninitialized in this function [-Wmaybe-uninitialized]
for (; i < pin_num; i++) {
^
drivers/pinctrl/pinctrl-amd.c:172:21: warning: 'i' may be used uninitialized in this function [-Wmaybe-uninitialized]
unsigned int bank, i, pin_num;
^
Fix this by adding a guarding default case for illegal
bank numbers.
Cc: S-k Shyam-sundar <Shyam-sundar.S-k@amd.com>
Cc: Nehal Shah <Nehal-bakulchandra.Shah@amd.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Now using function_desc structure instead of imx_pmx_func.
Also leveraging generic functions to retrieve functions count/name/groups.
The imx_free_funcs function can be removed since it is now handled by
the core driver during unregister.
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Now using group_desc structure instead of imx_pin_group.
Also leveraging generic functions to retrieve groups count/name/pins.
The imx_free_pingroups function can be removed since it is now handled by
the core driver during unregister.
Finally the device tree parsing is moved after the pinctrl driver registration
since this latter initializes the radix trees.
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
These four pins are for SDC4, not SDC1. They are grouped for
SDC4 later in the file so this must be a typo.
Reviewed-by: Björn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We can now drop the driver specific code for managing functions.
Signed-off-by: Tony Lindgren <tony@atomide.com>
[Replaces GENERIC_PINMUX with GENERIC_PINMUX_FUNCTIONS]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We can now drop the driver specific code for managing groups.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We can add generic helpers for function handling for cases where the pin
controller driver does not need to use static arrays.
Signed-off-by: Tony Lindgren <tony@atomide.com>
[Renamed the Kconfig item and moved things around]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Rename the symbol PINCTRL_GENERIC to PINCTRL_GENERIC_GROUPS since
it all pertains to groups. Replace everywhere.
ifdef out the radix tree and the struct when not using the
generic groups.
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We can add generic helpers for pin group handling for cases where the pin
controller driver does not need to use static arrays.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It confused me a bit so it may confuse others. Make it crystal
clear what is going on here for any future readers.
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Having the pin control framework call pin controller functions
before it's probe has finished is not nice as the pin controller
device driver does not yet have struct pinctrl_dev handle.
Let's fix this issue by adding deferred work for late init. This is
needed to be able to add pinctrl generic helper functions that expect
to know struct pinctrl_dev handle. Note that we now need to call
create_pinctrl() directly as we don't want to add the pin controller
to the list of controllers until the hogs are claimed. We also need
to pass the pinctrl_dev to the device tree parser functions as they
otherwise won't find the right controller at this point.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch fixes the wrong width of PINCFG_TYPE_DRV bitfields for Exynos5433
because PINCFG_TYPE_DRV of Exynos5433 has 4bit fields in the *_DRV
registers. Usually, other Exynos have 2bit field for PINCFG_TYPE_DRV.
Fixes: 3c5ecc9ed3 ("pinctrl: exynos: Add support for Exynos5433")
Cc: stable@vger.kernel.org
Cc: Tomasz Figa <tomasz.figa@gmail.com>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This change is inspired from the pinctrl-single architecture.
The problem with current implementation is that it isn't possible
to add/remove functions and/or groups dynamically. The radix tree
offers an easy way to do so. The intent is to offer a follow-up
patch later that will enable the use of pinctrl nodes in dt-overlays.
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Otherwise can't dynamically update fields such as ngroups which can
change over time (with a dt-overlay for instance).
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Trivial fixe to spelling mistake "Ivalid" to "Invalid" in
dev_err error message.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This is a non-functional change, which deletes code duplication in two
of four if-if branches by reordering the checks. Functional identity
of the code change can be shown by running through the whole truth table
of boolean arguments.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch updates my email address as I no longer have access to the old
one.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add some tab in order to improve indentation.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reference to 'sys2pci_np' should be dropped in all cases here, not only in
error handling path.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This activates strict mode muxing for the STM32 pin controllers,
as these do not allow GPIO and functions to use the same pin
simultaneously.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pinctrl_gpio_request is called with the "full" gpio number, already
containing the base, then meson_pmx_request_gpio is then called with the
final pin number.
Remove the base addition when calling meson_pmx_disable_other_groups.
Fixes: 6ac7309511 ("pinctrl: add driver for Amlogic Meson SoCs")
CC: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Acked-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In the function amd_gpio_irq_set_type, read the values from
the ACPI table to set the level and drop the settings passed
by the client.
Cc: <stable@vger.kernel.org> # 4.8.x+
Reviewed-by: Pankaj Sen <Pankaj.Sen@amd.com>
Reviewed-by: Nitesh Kumar Agrawal <Nitesh-kumar.Agrawal@amd.com>
Reviewed-by: Shah, Nehal-bakulchandra <Nehal-bakulchandra.Shah@amd.com>
Signed-off-by: Shyam-sundar S-k <Shyam-sundar.S-k@amd.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds support for new Bank and adds IRQCHIP_SKIP_SET_WAKE flag.
Reviewed-by: S-k, Shyam-sundar <Shyam-sundar.S-k@amd.com>
Signed-off-by: Nehal Shah <Nehal-bakulchandra.Shah@amd.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The patch introducing the g5 pinctrl driver implemented a smattering of
pins to flesh out the implementation of the core and provide bare-bones
support for some OpenPOWER platforms and the AST2500 evaluation board.
Now, update the bindings document to reflect the complete functionality
and implement the necessary pin configuration tables in the driver.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Joel Stanley <joel@jms.id.au>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The patch introducing the g4 pinctrl driver implemented a smattering of
pins to flesh out the implementation of the core and provide bare-bones
support for some OpenPOWER platforms. Now, update the bindings document
to reflect the complete functionality and implement the necessary pin
configuration tables in the driver.
Cc: Timothy Pearson <tpearson@raptorengineering.com>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Joel Stanley <joel@jms.id.au>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The System Control Unit IP block in the Aspeed SoCs is typically where
the pinmux configuration is found, but not always. A number of pins
depend on state in one of LPC Host Control (LHC) or SoC Display
Controller (GFX) IP blocks, so the Aspeed pinmux drivers should have the
means to adjust these as necessary.
We use syscon to cast a regmap over the GFX and LPC blocks, which is
used as an arbitration layer between the relevant driver and the pinctrl
subsystem. The regmaps are then exposed to the SoC-specific pinctrl
drivers by phandles in the devicetree, and are selected during a mux
request by querying a new 'ip' member in struct aspeed_sig_desc.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Voltage switching is the same as on the r8a7791.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds CAN FD[0-1] pinmux support to r8a7796 SoC.
Based on a patch for r8a7795 by Ramesh Shanmugasundaram.
Signed-off-by: Chris Paterson <chris.paterson2@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds CAN[0-1] pinmux support to r8a7796 SoC.
Based on a patch for r8a7795 by Ramesh Shanmugasundaram.
Signed-off-by: Chris Paterson <chris.paterson2@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
There are pins on the r8a7795 which are not part of a GPIO bank nor
can be muxed between different functions. They do however allow for the
bias to be configured. Add those pins to the list of pins and
to the bias configuration array.
The pins can now be referred to in DT by function names and their bias
setting set.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Implements pull-up and pull-down. On this SoC there is no simple mapping
of GP pins to bias register bits, so we need a table.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Define the drive strength registers for the R8A7796. Add pins which are
not part of a GPIO bank nor can be muxed between different functions but
which still allow for their drive-strength to be configured.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Lots of changes as usual, so I'm trying to be brief here. Most of the
new hardware support has the respective driver changes merged through
other trees or has had it available for a while, so this is where things
come together.
We get a DT descriptions for a couple of new SoCs, all of them variants
of other chips we already support, and usually coming with a new
evaluation board:
- Oxford semiconductor (now Broadcom) OX820 SoC for NAS devices
- Qualcomm MDM9615 LTE baseband
- NXP imx6ull, the latest and smallest i.MX6 application processor variant
- Renesas RZ/G (r8a7743 and r8a7745) application processors
- Rockchip PX3, a variant of the rk3188 chip used in Android tablets
- Rockchip rk1108 single-core application processor
- ST stm32f746 Cortex-M7 based microcontroller
- TI DRA71x automotive processors
These are commercially available consumer platforms we now support:
- Motorola Droid 4 (xt894) mobile phone
- Rikomagic MK808 Android TV stick based on Rockchips rx3066
- Cloud Engines PogoPlug v3 based on OX820
- Various Broadcom based wireless devices:
- Netgear R8500 router
- Tenda AC9 router
- TP-LINK Archer C9 V1
- Luxul XAP-1510 Access point
- Turris Omnia open hardware router based on Armada 385
And a couple of new boards targeted at developers, makers
or industrial integration:
- Macnica Sodia development platform for Altera socfpga (Cyclone V)
- MicroZed board based on Xilinx Zynq FPGA platforms
- TOPEET itop/elite based on exynos4412
- WP8548 MangOH Open Hardware platform for IOT, based on
Qualcomm MDM9615
- NextThing CHIP Pro gadget
- NanoPi M1 development board
- AM571x-IDK industrial board based on TI AM5718
- i.MX6SX UDOO Neo
- Boundary Devices Nitrogen6_SOM2 (i.MX6)
- Engicam i.CoreM6
- Grinn i.MX6UL liteSOM/liteBoard
- Toradex Colibri iMX6 module
Other changes:
- added peripherals on renesas, davinci, stm32f429, uniphier, sti,
mediatek, integrator, at91, imx, vybrid, ls1021a, omap, qualcomm,
mvebu, allwinner, broadcom, exynos, zynq
- Continued fixes for W=1 dtc warnings
- The old STiH415/416 SoC support gets removed, these never made it into
products and have served their purpose in the kernel as a template
for teh newer chips from ST
- The exynos4415 dtsi file is removed as nothing uses it.
- Intel PXA25x can now be booted using devicetree
Conflicts:
arch/arm/boot/dts/r8a*.dtsi: a node was added
the clk tree, keep both sides and watch out for git
dropping the required '};' at the end of each side.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=wJt3
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM DT updates from Arnd Bergmann:
"Lots of changes as usual, so I'm trying to be brief here. Most of the
new hardware support has the respective driver changes merged through
other trees or has had it available for a while, so this is where
things come together.
We get a DT descriptions for a couple of new SoCs, all of them
variants of other chips we already support, and usually coming with a
new evaluation board:
- Oxford semiconductor (now Broadcom) OX820 SoC for NAS devices
- Qualcomm MDM9615 LTE baseband
- NXP imx6ull, the latest and smallest i.MX6 application processor variant
- Renesas RZ/G (r8a7743 and r8a7745) application processors
- Rockchip PX3, a variant of the rk3188 chip used in Android tablets
- Rockchip rk1108 single-core application processor
- ST stm32f746 Cortex-M7 based microcontroller
- TI DRA71x automotive processors
These are commercially available consumer platforms we now support:
- Motorola Droid 4 (xt894) mobile phone
- Rikomagic MK808 Android TV stick based on Rockchips rx3066
- Cloud Engines PogoPlug v3 based on OX820
- Various Broadcom based wireless devices:
- Netgear R8500 router
- Tenda AC9 router
- TP-LINK Archer C9 V1
- Luxul XAP-1510 Access point
- Turris Omnia open hardware router based on Armada 385
And a couple of new boards targeted at developers, makers or
industrial integration:
- Macnica Sodia development platform for Altera socfpga (Cyclone V)
- MicroZed board based on Xilinx Zynq FPGA platforms
- TOPEET itop/elite based on exynos4412
- WP8548 MangOH Open Hardware platform for IOT, based on Qualcomm MDM9615
- NextThing CHIP Pro gadget
- NanoPi M1 development board
- AM571x-IDK industrial board based on TI AM5718
- i.MX6SX UDOO Neo
- Boundary Devices Nitrogen6_SOM2 (i.MX6)
- Engicam i.CoreM6
- Grinn i.MX6UL liteSOM/liteBoard
- Toradex Colibri iMX6 module
Other changes:
- added peripherals on renesas, davinci, stm32f429, uniphier, sti,
mediatek, integrator, at91, imx, vybrid, ls1021a, omap, qualcomm,
mvebu, allwinner, broadcom, exynos, zynq
- Continued fixes for W=1 dtc warnings
- The old STiH415/416 SoC support gets removed, these never made it
into products and have served their purpose in the kernel as a
template for teh newer chips from ST
- The exynos4415 dtsi file is removed as nothing uses it.
- Intel PXA25x can now be booted using devicetree"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (422 commits)
arm: dts: zynq: Add MicroZed board support
ARM: dts: da850: enable high speed for mmc
ARM: dts: da850: Add node for pullup/pulldown pinconf
ARM: dts: da850: enable memctrl and mstpri nodes per board
ARM: dts: da850-lcdk: Add ethernet0 alias to DT
ARM: dts: artpec: add pcie support
ARM: dts: add support for Turris Omnia
devicetree: Add vendor prefix for CZ.NIC
ARM: dts: berlin2q-marvell-dmp: fix typo in chosen node
ARM: dts: berlin2q-marvell-dmp: fix regulators' name
ARM: dts: Add xo to sdhc clock node on qcom platforms
ARM: dts: r8a7794: Add device node for PRR
ARM: dts: r8a7793: Add device node for PRR
ARM: dts: r8a7792: Add device node for PRR
ARM: dts: r8a7791: Add device node for PRR
ARM: dts: r8a7790: Add device node for PRR
ARM: dts: r8a7779: Add device node for PRR
ARM: dts: r8a73a4: Add device node for PRR
ARM: dts: sk-rzg1e: add Ether support
ARM: dts: sk-rzg1e: initial device tree
...
No core changes this time. Mainly gradual improvement and
feature growth in the drivers.
New drivers:
- New driver for TI DA850/OMAP-L138/AM18XX pinconf
- The SX150x was moved over from the GPIO subsystem and
reimagined as a pin control driver with GPIO support
in a joint effort by three independent users of this
hardware. The result was amazingly good!
- New subdriver for the Oxnas OX820
Improvements:
- The sunxi driver now supports the generic pin control
bindings rather than the sunxi-specific. Add debouncing
support to the driver.
- Simplifications in pinctrl-single adding a generic parser.
- Two downstream fixes and move the Raspberry Pi BCM2835 over
to use the generic GPIOLIB_IRQCHIP.
-----BEGIN PGP SIGNATURE-----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=Pkzu
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pinctrl updates from Linus Walleij:
"Bulk pin control changes for the v4.10 kernel cycle:
No core changes this time. Mainly gradual improvement and
feature growth in the drivers.
New drivers:
- New driver for TI DA850/OMAP-L138/AM18XX pinconf
- The SX150x was moved over from the GPIO subsystem and reimagined as
a pin control driver with GPIO support in a joint effort by three
independent users of this hardware. The result was amazingly good!
- New subdriver for the Oxnas OX820
Improvements:
- The sunxi driver now supports the generic pin control bindings
rather than the sunxi-specific. Add debouncing support to the
driver.
- Simplifications in pinctrl-single adding a generic parser.
- Two downstream fixes and move the Raspberry Pi BCM2835 over to use
the generic GPIOLIB_IRQCHIP"
* tag 'pinctrl-v4.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (92 commits)
pinctrl: sx150x: use new nested IRQ infrastructure
pinctrl: sx150x: handle missing 'advanced' reg in sx1504 and sx1505
pinctrl: sx150x: rename 'reg_advance' to 'reg_advanced'
pinctrl: sx150x: access the correct bits in the 4-bit regs of sx150[147]
pinctrl: mt8173: set GPIO16 to usb iddig mode
pinctrl: bcm2835: switch to GPIOLIB_IRQCHIP
pinctrl: New driver for TI DA850/OMAP-L138/AM18XX pinconf
devicetree: bindings: pinctrl: Add binding for ti,da850-pupd
Documentation: pinctrl: palmas: Add ti,palmas-powerhold-override property definition
pinctrl: intel: set default handler to be handle_bad_irq()
pinctrl: sx150x: add support for sx1501, sx1504, sx1505 and sx1507
pinctrl: sx150x: sort chips by part number
pinctrl: sx150x: use correct registers for reg_sense (sx1502 and sx1508)
pinctrl: imx: fix imx_pinctrl_desc initialization
pinctrl: sx150x: support setting multiple pins at once
pinctrl: sx150x: various spelling fixes and some white-space cleanup
pinctrl: mediatek: use builtin_platform_driver
pinctrl: stm32: use builtin_platform_driver
pinctrl: sunxi: Testing the wrong variable
pinctrl: nomadik: split up and comments MC0 pins
...
Core changes:
- Simplify threaded interrupt handling: instead of passing
numbed parameters to gpiochip_irqchip_add_chained() we
create a new call: gpiochip_irqchip_add_nested() so the two
types are clearly semantically different. Also make sure
that all nested chips call gpiochip_set_nested_irqchip()
which is necessary for IRQ resend to work properly if
it happens.
- Return error on seek operations for the chardev.
- Clamp values set as part of gpio[d]_direction_output() so
that anything != 0 will be send down to the driver as "1"
not the value passed in.
- ACPI can now support naming of GPIO lines, hogs and holes
in the GPIO lists.
New drivers:
- The SX150x driver was deemed unfit for the GPIO subsystem
and was moved over to a combined GPIO+pinctrl driver in the
pinctrl subsystem.
New features:
- Various cleanups to various drivers.
-----BEGIN PGP SIGNATURE-----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=2UpT
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Luinus Walleij:
"Bulk GPIO changes for the v4.10 kernel cycle:
Core changes:
- Simplify threaded interrupt handling: instead of passing numbed
parameters to gpiochip_irqchip_add_chained() we create a new call:
gpiochip_irqchip_add_nested() so the two types are clearly
semantically different. Also make sure that all nested chips call
gpiochip_set_nested_irqchip() which is necessary for IRQ resend to
work properly if it happens.
- Return error on seek operations for the chardev.
- Clamp values set as part of gpio[d]_direction_output() so that
anything != 0 will be send down to the driver as "1" not the value
passed in.
- ACPI can now support naming of GPIO lines, hogs and holes in the
GPIO lists.
New drivers:
- The SX150x driver was deemed unfit for the GPIO subsystem and was
moved over to a combined GPIO+pinctrl driver in the pinctrl
subsystem.
New features:
- Various cleanups to various drivers"
* tag 'gpio-v4.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (49 commits)
gpio: merrifield: Implement gpio_get_direction callback
gpio: merrifield: Add support for hardware debouncer
gpio: chardev: Return error for seek operations
gpio: arizona: Tidy up probe error path
gpio: arizona: Remove pointless set of platform drvdata
gpio: pl061: delete platform data handling
gpio: pl061: move platform data into driver
gpio: pl061: rename variable from chip to pl061
gpio: pl061: rename state container struct
gpio: pl061: use local state for parent IRQ storage
gpio: set explicit nesting on drivers
gpio: simplify adding threaded interrupts
gpio: vf610: use builtin_platform_driver
gpio: axp209: use correct register for GPIO input status
gpio: stmpe: fix interrupt handling bug
gpio: em: depnd on ARCH_SHMOBILE
gpio: zx: depend on ARCH_ZX
gpio: x86: update config dependencies for x86 specific hardware
gpio: mb86s7x: use builtin_platform_driver
gpio: etraxfs: use builtin_platform_driver
...
Use the new gpiochip_irqchip_add_nested() and
gpiochip_set_nested_irqchip() calls to properly created
a nested irqchip and mark all child irqs properly with
their parent IRQ.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This fixes a problem where sx150x_regmap_reg_width() returns 8 for the
data register (reg 0) for sx1504 where it should return 4, and return
a correct 8 for sx1505 but for the wrong reason (both chips lack the
'advanced' register). This is not a real problem, since nothing depends
on the function returning 4 or 8, and certainly not if it is returning
8 for the wrong reason. But fix this to avoid nasty surprises down the
line.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This matches the datasheets and is less confusing since the register
has nothing to with advancing anything.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The code assumes 8-bit or 16-bit width registers, but three of the
chips (sx1501/sx1504/sx1507) are 4-bit. So, try to handle 4-bit chips as
well, they leave the high part of each register unused.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
the default mode of GPIO16 pin is gpio, when set EINT16 to
IRQ_TYPE_LEVEL_HIGH, no interrupt is triggered, it can be
fixed when set its default mode as usb iddig.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Acked-by: Hongzhou Yang <hongzhou.yang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It should be possible to use the GPIOLIB_IRQCHIP helper
library with the BCM2835 driver since it is a pretty straight
forward cascaded irqchip.
The only difference from other drivers is that the BCM2835
has several banks for a single gpiochip, and each bank has
a separate IRQ line. Instead of creating one gpiochip per
bank, a single gpiochip covers all banks GPIO lines. This
makes it necessary to resolve the bank ID in the IRQ
handler.
The GPIOLIB_IRQCHIP allows several IRQs to be cascaded off
the same gpiochip by calling gpiochip_set_chained_irqchip()
repeatedly, but we have been a bit short on examples
for how this should be handled in practice, so this is intended
as an example of how this can be achieved.
The old code did not model the chip as a chained interrupt
handler, but this patch also rectifies that situation.
Cc: Stephen Warren <swarren@wwwdotorg.org>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Tested-by: Eric Anholt <eric@anholt.net>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds a new driver for pinconf on TI DA850/OMAP-L138/AM18XX. These
SoCs have a separate controller for controlling pullup/pulldown groups.
Signed-off-by: David Lechner <david@lechnology.com>
Reviewed-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We switch the default handler to be handle_bad_irq() instead of
handle_simple_irq() (which was not correct anyway).
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
please pull the following:
- Rafal adds support for the Netgear R8500 routers, adds basic support
for the Tenda AC9 router which uses the new BCM53573 SoC (single core Cortex
A7). He also enables the UART on the Netgear R8000 and restructures the
include files a bit for the BCM47094 SoC, finally he adds USB 3.0 PHY nodes
which enables USB 3.0 on BCM5301X devices that support it. Finally he adds
support for the TP-LINK Archer C9 V1 router.
- Kamal adds support for the QSPI controller on the Northstar Plus SoCs and updates
the bcm958625k reference board to have it enabled
- Dan adds support for the Luxul XAP-1510 (using a BCM4708) and XWR-3100 (using
a BCM47094)
- Scott fixes the pinctrl names in the Cygnus DTS files
- Jonathan enables the Broadcom iProc mailbox controller for Broadcom Cygnus/iProc
SoCs, he adds interrupt support for the GPIO CRMU hardware block and finally adds
the node for the OTP controller found on Cygnus SoCs
- Dhananjay enables the GPIO B controller on Norstarh Plus SoCs
- Eric defines standard pinctrl groups in the BCM2835 GPIO node
- Gerd adds definitions for the pinctrl groups and updates the PWM, I2C and SDHCI nodes
to use their appropriate pinctrl functions
- Linus adds names for the Raspberry Pi GPIO lines based on the datasheet
- Martin adds the DT binding and nodes for the Raspberry Pi firmware thermal block
- Stefan fixes a few typos with respect to the BCM2835 mailbox binding example and
Device Tree nodes he also fixes the Raspberry Pi GPIO lines names and finally
adds names for the Raspberry Zero GPIO lines
-----BEGIN PGP SIGNATURE-----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=4GFQ
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-4.10/devicetree' of http://github.com/Broadcom/stblinux into next/dt
Pull "Broadcom devicetree changes for 4.10" from Florian Fainelli:
This pull request contains Broadcom ARM-based SoC Device Tree changes for 4.10,
please pull the following:
- Rafal adds support for the Netgear R8500 routers, adds basic support
for the Tenda AC9 router which uses the new BCM53573 SoC (single core Cortex
A7). He also enables the UART on the Netgear R8000 and restructures the
include files a bit for the BCM47094 SoC, finally he adds USB 3.0 PHY nodes
which enables USB 3.0 on BCM5301X devices that support it. Finally he adds
support for the TP-LINK Archer C9 V1 router.
- Kamal adds support for the QSPI controller on the Northstar Plus SoCs and updates
the bcm958625k reference board to have it enabled
- Dan adds support for the Luxul XAP-1510 (using a BCM4708) and XWR-3100 (using
a BCM47094)
- Scott fixes the pinctrl names in the Cygnus DTS files
- Jonathan enables the Broadcom iProc mailbox controller for Broadcom Cygnus/iProc
SoCs, he adds interrupt support for the GPIO CRMU hardware block and finally adds
the node for the OTP controller found on Cygnus SoCs
- Dhananjay enables the GPIO B controller on Norstarh Plus SoCs
- Eric defines standard pinctrl groups in the BCM2835 GPIO node
- Gerd adds definitions for the pinctrl groups and updates the PWM, I2C and SDHCI nodes
to use their appropriate pinctrl functions
- Linus adds names for the Raspberry Pi GPIO lines based on the datasheet
- Martin adds the DT binding and nodes for the Raspberry Pi firmware thermal block
- Stefan fixes a few typos with respect to the BCM2835 mailbox binding example and
Device Tree nodes he also fixes the Raspberry Pi GPIO lines names and finally
adds names for the Raspberry Zero GPIO lines
* tag 'arm-soc/for-4.10/devicetree' of http://github.com/Broadcom/stblinux: (29 commits)
ARM: bcm2835: Add names for the RPi Zero GPIO lines
ARM: bcm2835: Fix names for the Raspberry Pi GPIO lines
ARM: dts: enable GPIO-b for Broadcom NSP
ARM: BCM5301X: Add DT for TP-LINK Archer C9 V1
ARM: dts: Add node for Broadcom OTP controller driver
ARM: dts: Enable interrupt support for cygnus crmu gpio driver
ARM: dts: Enable Broadcom iProc mailbox controller
ARM: bcm2835: Add names for the Raspberry Pi GPIO lines
ARM: bcm2835: dts: add thermal node to device-tree of bcm283x
dt: bindings: add thermal device driver for bcm2835
ARM: dts: bcm283x: fix typo in mailbox address
DT: binding: bcm2835-mbox: fix address typo in example
ARM: dts: cygnus: fix naming of pinctrl node
ARM: BCM53573: Specify PMU and its ILP clock in the DT
ARM: BCM5301X: Add DT for Luxul XWR-3100
ARM: BCM5301X: Add DT for Luxul XAP-1510
ARM: BCM5301X: Specify USB 3.0 PHY in DT
ARM: BCM5301X: Enable UART on Netgear R8000
ARM: BCM5301X: Add separated DTS include file for BCM47094
ARM: dts: NSP: Add QSPI nodes to NSPI and bcm958625k DTSes
...
Alexandre Belloni
Geert Uytterhoeven
Jesper Nilsson
Martin Blumenstingl
Tony Lindgren
Sergei Shtylyov
Linus Walleij
Jerome Brunet
Neil Armstrong
John Keeping
Masanari Iida
Charles Keepax
Marek Szyprowski
Hans de Goede
Andy Yan
Christian Lamparter
Patrice Chotard
Bjorn Andersson
Andrzej Hajda
Peter Robinson
Jeffy Chen
Masahiro Yamada
Julia Cartwright
Timur Tabi
david.wu
Icenowy Zheng
Andy Shevchenko
Rick Altherr
Kunihiko Hayashi
Linus Torvalds
Wei Yongjun
Dan Carpenter
Paul Gortmaker
Chen-Yu Tsai
Arnd Bergmann
Alexandre TORGUE
Alexander Stein
Mika Westerberg
Kalyan Kinthada
Maxime Ripard
Jisheng Zhang
Jean Delvare
Andrew Jeffery
Jacopo Mondi
Krzysztof Kozlowski
Colin Ian King
Russell King
Markus Elfring
Thierry Reding
David Lechner
Nishanth Menon
Jon Hunter
Gary Bisson
Chanwoo Choi
Vladimir Zapolskiy
John Crispin
Christophe JAILLET
Gabriel Fernandez
Shyam Sundar S K
Shah, Nehal-bakulchandra
Ulrich Hecht
Simon Horman
Takeshi Kihara
Chris Paterson
Niklas Söderlund
Peter Rosin
Chunfeng Yun