Previously, the ASoC 'platform' (PCM/DMA) object was instantiated via a
platform_device. This didn't represent the hardware well, since there
was no separate hardware associated with this platform_device; it was a
virtual device with sole purpose to call snd_soc_register_platform().
This change removes the platform_device completely. Each Samsung DAI now
registers the ASoC 'platform' itself. Machine drivers are adjusted for
the new 'platform' name.
Signed-off-by: Padmavathi Venna <padma.v@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Depending on the Codec, the the BCLK/LRCLK ratio might not be freely
chosen by the CPU DAI.
For example, some Codec might want to be supplied with 32-bit samples
for both its channels regardless of the actual audio word size the CPU
sends. In such cases, the rest of the bits on the data lines must be
padded with zeros:
_______________________________
LRCLK / \
--' `---------- .....
BCLK ||||||||||||||||||||||||||||||||||||||||||||||| .....
DATA ____||||||||||||||||_________________|||||||||| .....
|<-- data -->|<-- pads --> |
This patch adds a new clock divider to configure the BCLK/LRCLK ratio.
If the machine code uses that divider, the driver uses the specified
value, instead of deriving that information from the audio word size.
Otherwise, the original behaviour is retained.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Change davinci_config_channel_size() to derive the values for XSSZ and
XROT in DAVINCI_MCASP_[RT]XFMT_REG from the configured word length
rather than hard-coding them in a switch/case block.
Also, by directly passing the word length to
davinci_config_channel_size(), we can get rid of the
DAVINCI_AUDIO_WORD_* enum.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
codec_fmt and sample_rate variables are unused in both snd_platform_data
and davinci_audio_dev, so drop them.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The common machine driver will be able to support new boards where the voice
port is also in use.
At the same time add possibility to fine tune the connections from twl4030
on the board: jack detection GPIO, input/output selection
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
So the code to suppress duplicate changes is effective.
Reported-by: Kyung Kwee Ryu <Kyung-Kwee.Ryu@wolfsonmicro.comyu@wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Provide robustness against low quality FLL sync clocks by increasing the
timeout for lock to an absurdly high point; we should never get anywhere
near hitting the timeout in a real system unless it is failing.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The machine driver try to use GPIO15 of twl4030 for HS MUX which supposed to
select between TWL's HSOL/R and tlv320aic3254's HPL/R.
The TWL's GPIO allocated dynamically so the (OMAP_MAX_GPIO_LINES + 15) is no
longer valid GPIO number causing a kernel crash due to BUG_ON()
Also the current machine driver supports only TWL audio currently: there is
no need to control the GPIO.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use of devm_regmap_init_spi does not require an explicit
regmap_exit call.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown
Padmavathi Venna
Daniel Mack
Peter Ujfalusi
Sachin Kamat