Currently .get_state() and .apply() use dev_get_drvdata() on the struct
device related to the pwm chip. This only works after .probe() called
platform_set_drvdata() which in this driver happens only after
pwmchip_add() and so comes possibly too late.
Instead of setting the driver data earlier use the traditional
container_of approach as this way the driver data is conceptually and
computational nearer.
Fixes: 9db33d221e ("pwm: Add support for sl28cpld PWM controller")
Tested-by: Michael Walle <michael@walle.cc>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
SoC changes, a substantial part of this is cleanup of some of the older
platforms that used to have a bunch of board files. In particular:
- Removal of non-DT i.MX platforms that haven't seen activity in years,
it's time to remove them.
- A bunch of cleanup and removal of platform data for TI/OMAP platforms,
moving over to genpd for power/reset control (yay!)
- Major cleanup of Samsung S3C24xx and S3C64xx platforms, moving them
closer to multiplatform support (not quite there yet, but getting
close).
THere are a few other changes too, smaller fixlets, etc. For new
platform support, the primary ones re:
- New SoC: Hisilicon SD5203, ARM926EJ-S platform.
- Cpufreq support for i.MX7ULP
-----BEGIN PGP SIGNATURE-----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=0+Ee
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC platform updates from Olof Johansson:
"SoC changes, a substantial part of this is cleanup of some of the
older platforms that used to have a bunch of board files.
In particular:
- Remove non-DT i.MX platforms that haven't seen activity in years,
it's time to remove them.
- A bunch of cleanup and removal of platform data for TI/OMAP
platforms, moving over to genpd for power/reset control (yay!)
- Major cleanup of Samsung S3C24xx and S3C64xx platforms, moving them
closer to multiplatform support (not quite there yet, but getting
close).
There are a few other changes too, smaller fixlets, etc. For new
platform support, the primary ones are:
- New SoC: Hisilicon SD5203, ARM926EJ-S platform.
- Cpufreq support for i.MX7ULP"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (121 commits)
ARM: mstar: Select MStar intc
ARM: stm32: Replace HTTP links with HTTPS ones
ARM: debug: add UART early console support for SD5203
ARM: hisi: add support for SD5203 SoC
ARM: omap3: enable off mode automatically
clk: imx: imx35: Remove mx35_clocks_init()
clk: imx: imx31: Remove mx31_clocks_init()
clk: imx: imx27: Remove mx27_clocks_init()
ARM: imx: Remove unused definitions
ARM: imx35: Retrieve the IIM base address from devicetree
ARM: imx3: Retrieve the AVIC base address from devicetree
ARM: imx3: Retrieve the CCM base address from devicetree
ARM: imx31: Retrieve the IIM base address from devicetree
ARM: imx27: Retrieve the CCM base address from devicetree
ARM: imx27: Retrieve the SYSCTRL base address from devicetree
ARM: s3c64xx: bring back notes from removed debug-macro.S
ARM: s3c24xx: fix Wunused-variable warning on !MMU
ARM: samsung: fix PM debug build with DEBUG_LL but !MMU
MAINTAINERS: mark linux-samsung-soc list non-moderated
ARM: imx: Remove remnant board file support pieces
...
cros-ec:
* Error code cleanup across cros-ec by Guenter.
* Remove cros_ec_cmd_xfer in favor of cros_ec_cmd_xfer_status.
cros_ec_typec:
* Landed initial USB4 support in typec connector class driver for cros_ec.
* Role switch bugfix on disconnect, and reordering configuration steps.
cros_ec_lightbar:
* Fix buffer outsize and result for get_lightbar_version.
misc:
* Remove config MFD_CROS_EC, now that transition from MFD is complete.
* Enable KEY_LEFTMETA in new location on arm based cros-ec-keyboard keymap.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQQCtZK6p/AktxXfkOlzbaomhzOwwgUCX5G2IAAKCRBzbaomhzOw
wo4JAQC7BcJJwYgoVnRQvYd4xXCEsl/F9cVFJJLRYAH/PA4x6gEA+wfdIxebAXbO
RapU2HOppxiQGFkr+0FX5xV+O7cRNAo=
=gkul
-----END PGP SIGNATURE-----
Merge tag 'tag-chrome-platform-for-v5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux
Pull chrome platform updates from Benson Leung:
"cros-ec:
- Error code cleanup across cros-ec by Guenter
- Remove cros_ec_cmd_xfer in favor of cros_ec_cmd_xfer_status
cros_ec_typec:
- Landed initial USB4 support in typec connector class driver for
cros_ec
- Role switch bugfix on disconnect, and reordering configuration
steps
cros_ec_lightbar:
- Fix buffer outsize and result for get_lightbar_version
misc:
- Remove config MFD_CROS_EC, now that transition from MFD is complete
- Enable KEY_LEFTMETA in new location on arm based cros-ec-keyboard
keymap"
* tag 'tag-chrome-platform-for-v5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux:
ARM: dts: cros-ec-keyboard: Add alternate keymap for KEY_LEFTMETA
platform/chrome: Use kobj_to_dev() instead of container_of()
platform/chrome: cros_ec_proto: Drop cros_ec_cmd_xfer()
platform/chrome: cros_ec_proto: Update cros_ec_cmd_xfer() call-sites
platform/chrome: Kconfig: Remove the transitional MFD_CROS_EC config
platform/chrome: cros_ec_lightbar: Reduce ligthbar get version command
platform/chrome: cros_ec_trace: Add fields to command traces
platform/chrome: cros_ec_typec: Re-order connector configuration steps
platform/chrome: cros_ec_typec: Avoid setting usb role twice during disconnect
platform/chrome: cros_ec_typec: Send enum values to usb_role_switch_set_role()
platform/chrome: cros_ec_typec: USB4 support
pwm: cros-ec: Simplify EC error handling
platform/chrome: cros_ec_proto: Convert EC error codes to Linux error codes
platform/input: cros_ec: Replace -ENOTSUPP with -ENOPROTOOPT
pwm: cros-ec: Accept more error codes from cros_ec_cmd_xfer_status
platform/chrome: cros_ec_sysfs: Report range of error codes from EC
cros_ec_lightbar: Accept more error codes from cros_ec_cmd_xfer_status
iio: cros_ec: Accept -EOPNOTSUPP as 'not supported' error code
This release cycle's updates are mostly cleanup and some minor fixes.
-----BEGIN PGP SIGNATURE-----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=zEte
-----END PGP SIGNATURE-----
Merge tag 'pwm/for-5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"This release cycle's updates are mostly cleanup and some minor fixes"
* tag 'pwm/for-5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm:
dt-bindings: pwm: renesas,pwm-rcar: Add r8a7742 support
dt-bindings: pwm: renesas,tpu-pwm: Document r8a7742 support
pwm: Allow store 64-bit duty cycle from sysfs interface
pwm: img: Fix null pointer access in probe
pwm: pca9685: Disable unused alternative addresses
pwm: pca9685: Use BIT() macro instead of shift
pwm: pca9685: Make comments more consistent
pwm: sun4i: Simplify with dev_err_probe()
pwm: sprd: Simplify with dev_err_probe()
pwm: sifive: Simplify with dev_err_probe()
pwm: rockchip: Simplify with dev_err_probe()
pwm: jz4740: Simplify with dev_err_probe()
pwm: bcm2835: Simplify with dev_err_probe()
pwm: Convert to use DEFINE_SEQ_ATTRIBUTE macro
pwm: rockchip: Keep enabled PWMs running while probing
dt-bindings: pwm: renesas,pwm-rcar: Add r8a774e1 support
New driver:
Cadence MHDP8546 DisplayPort bridge driver
core:
- cross-driver scatterlist cleanups
- devm_drm conversions
- remove drm_dev_init
- devm_drm_dev_alloc conversion
ttm:
- lots of refactoring and cleanups
bridges:
- chained bridge support in more drivers
panel:
- misc new panels
scheduler:
- cleanup priority levels
displayport:
- refactor i915 code into helpers for nouveau
i915:
- split into display and GT trees
- WW locking refactoring in GEM
- execbuf2 extension mechanism
- syncobj timeline support
- GEN 12 HOBL display powersaving
- Rocket Lake display additions
- Disable FBC on Tigerlake
- Tigerlake Type-C + DP improvements
- Hotplug interrupt refactoring
amdgpu:
- Sienna Cichlid updates
- Navy Flounder updates
- DCE6 (SI) support for DC
- Plane rotation enabled
- TMZ state info ioctl
- PCIe DPC recovery support
- DC interrupt handling refactor
- OLED panel fixes
amdkfd:
- add SMI events for thermal throttling
- SMI interface events ioctl update
- process eviction counters
radeon:
- move to dma_ for allocations
- expose sclk via sysfs
msm:
- DSI support for sm8150/sm8250
- per-process GPU pagetable support
- Displayport support
mediatek:
- move HDMI phy driver to PHY
- convert mtk-dpi to bridge API
- disable mt2701 tmds
tegra:
- bridge support
exynos:
- misc cleanups
vc4:
- dual display cleanups
ast:
- cleanups
gma500:
- conversion to GPIOd API
hisilicon:
- misc reworks
ingenic:
- clock handling and format improvements
mcde:
- DSI support
mgag200:
- desktop g200 support
mxsfb:
- i.MX7 + i.MX8M
- alpha plane support
panfrost:
- devfreq support
- amlogic SoC support
ps8640:
- EDID from eDP retrieval
tidss:
- AM65xx YUV workaround
virtio:
- virtio-gpu exported resources
rcar-du:
- R8A7742, R8A774E1 and R8A77961 support
- YUV planar format fixes
- non-visible plane handling
- VSP device reference count fix
- Kconfig fix to avoid displaying disabled options in .config
-----BEGIN PGP SIGNATURE-----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=4H8J
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2020-10-15' of git://anongit.freedesktop.org/drm/drm
Pull drm updates from Dave Airlie:
"Not a major amount of change, the i915 trees got split into display
and gt trees to better facilitate higher level review, and there's a
major refactoring of i915 GEM locking to use more core kernel concepts
(like ww-mutexes). msm gets per-process pagetables, older AMD SI cards
get DC support, nouveau got a bump in displayport support with common
code extraction from i915.
Outside of drm this contains a couple of patches for hexint
moduleparams which you've acked, and a virtio common code tree that
you should also get via it's regular path.
New driver:
- Cadence MHDP8546 DisplayPort bridge driver
core:
- cross-driver scatterlist cleanups
- devm_drm conversions
- remove drm_dev_init
- devm_drm_dev_alloc conversion
ttm:
- lots of refactoring and cleanups
bridges:
- chained bridge support in more drivers
panel:
- misc new panels
scheduler:
- cleanup priority levels
displayport:
- refactor i915 code into helpers for nouveau
i915:
- split into display and GT trees
- WW locking refactoring in GEM
- execbuf2 extension mechanism
- syncobj timeline support
- GEN 12 HOBL display powersaving
- Rocket Lake display additions
- Disable FBC on Tigerlake
- Tigerlake Type-C + DP improvements
- Hotplug interrupt refactoring
amdgpu:
- Sienna Cichlid updates
- Navy Flounder updates
- DCE6 (SI) support for DC
- Plane rotation enabled
- TMZ state info ioctl
- PCIe DPC recovery support
- DC interrupt handling refactor
- OLED panel fixes
amdkfd:
- add SMI events for thermal throttling
- SMI interface events ioctl update
- process eviction counters
radeon:
- move to dma_ for allocations
- expose sclk via sysfs
msm:
- DSI support for sm8150/sm8250
- per-process GPU pagetable support
- Displayport support
mediatek:
- move HDMI phy driver to PHY
- convert mtk-dpi to bridge API
- disable mt2701 tmds
tegra:
- bridge support
exynos:
- misc cleanups
vc4:
- dual display cleanups
ast:
- cleanups
gma500:
- conversion to GPIOd API
hisilicon:
- misc reworks
ingenic:
- clock handling and format improvements
mcde:
- DSI support
mgag200:
- desktop g200 support
mxsfb:
- i.MX7 + i.MX8M
- alpha plane support
panfrost:
- devfreq support
- amlogic SoC support
ps8640:
- EDID from eDP retrieval
tidss:
- AM65xx YUV workaround
virtio:
- virtio-gpu exported resources
rcar-du:
- R8A7742, R8A774E1 and R8A77961 support
- YUV planar format fixes
- non-visible plane handling
- VSP device reference count fix
- Kconfig fix to avoid displaying disabled options in .config"
* tag 'drm-next-2020-10-15' of git://anongit.freedesktop.org/drm/drm: (1494 commits)
drm/ingenic: Fix bad revert
drm/amdgpu: Fix invalid number of character '{' in amdgpu_acpi_init
drm/amdgpu: Remove warning for virtual_display
drm/amdgpu: kfd_initialized can be static
drm/amd/pm: setup APU dpm clock table in SMU HW initialization
drm/amdgpu: prevent spurious warning
drm/amdgpu/swsmu: fix ARC build errors
drm/amd/display: Fix OPTC_DATA_FORMAT programming
drm/amd/display: Don't allow pstate if no support in blank
drm/panfrost: increase readl_relaxed_poll_timeout values
MAINTAINERS: Update entry for st7703 driver after the rename
Revert "gpu/drm: ingenic: Add option to mmap GEM buffers cached"
drm/amd/display: HDMI remote sink need mode validation for Linux
drm/amd/display: Change to correct unit on audio rate
drm/amd/display: Avoid set zero in the requested clk
drm/amdgpu: align frag_end to covered address space
drm/amdgpu: fix NULL pointer dereference for Renoir
drm/vmwgfx: fix regression in thp code due to ttm init refactor.
drm/amdgpu/swsmu: add interrupt work handler for smu11 parts
drm/amdgpu/swsmu: add interrupt work function
...
PWM core was converted to u64 by the commit a9d887dc1c ("pwm: Convert
period and duty cycle to u64") but did not change the duty_cycle_store()
so it will error out if trying to pass a numeric string bigger than
2^32-1.
Fix this by using u64 and kstrtou64() in duty_cycle_store().
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Guru Das Srinagesh <gurus@codeaurora.org>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
dev_get_drvdata() is called in img_pwm_runtime_resume() before the
driver data is set.
When pm_runtime_enabled() returns false in img_pwm_probe() it calls
img_pwm_runtime_resume() which results in a null pointer access.
This patch fixes the problem by setting the driver data earlier in the
img_pwm_probe() function.
This crash was seen when booting the Imagination Technologies Creator
Ci40 (Marduk) with kernel 5.4 in OpenWrt.
Fixes: e690ae5262 ("pwm: img: Add runtime PM")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The PCA9685 supports listening to 1 or more alternative I2C chip addresses
for some special features that this driver does not support.
By default the LED ALLCALL address is active (default 0x70), which causes
this chip to respond to address 0x70 in addition to its main address
(0x41). This is not desireable if there is another device on the same bus
that uses this address (like a TMP103 for example).
Since this feature is not supported by this driver, it is best to disable
these addresses in the chip to avoid unsuspected bus collisions.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Make all explanatory comments start with an uppercase char.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and also it prints the error value.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and also it prints the error value.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Chunyan Zhang <zhang.lyra@gmail.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and also it prints the error value.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Palmer Dabbelt <palmerdabbelt@google.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and also it prints the error value.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and also it prints the error value.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and also it prints the error value.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Use DEFINE_SEQ_ATTRIBUTE macro to simplify the code.
Signed-off-by: Liu Shixin <liushixin2@huawei.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Following commit cfc4c189bc ("pwm: Read initial hardware state at
request time") the Rockchip PWM driver can no longer assume a device's
pwm_state structure has been populated after a call to pwmchip_add().
Consequently, the test in rockchip_pwm_probe() intended to prevent the
driver from stopping PWM devices already enabled by the bootloader no
longer functions reliably and this can lead to the kernel hanging
during startup, particularly on devices like the Pinebook Pro that use
a PWM-controlled backlight for their display.
Avoid this by querying the device directly at probe time to determine
whether or not it is enabled.
Fixes: cfc4c189bc ("pwm: Read initial hardware state at request time")
Signed-off-by: Simon South <simon@simonsouth.net>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Add support for the PWM controller of the sl28cpld board management
controller. This is part of a multi-function device driver.
The controller has one PWM channel and can just generate four distinct
frequencies.
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Implement the pwm_ops.get_state() method to complete the support for the
new atomic PWM API.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200903112337.4113-14-hdegoede@redhat.com
Replace the enable, disable and config pwm_ops with an apply op,
to support the new atomic PWM API.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200903112337.4113-13-hdegoede@redhat.com
The pwm-crc code is using 2 different enable bits:
1. bit 7 of the PWM0_CLK_DIV (PWM_OUTPUT_ENABLE)
2. bit 0 of the BACKLIGHT_EN register
So far we've kept the PWM_OUTPUT_ENABLE bit set when disabling the PWM,
this commit makes crc_pwm_disable() clear it on disable and makes
crc_pwm_enable() set it again on re-enable.
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200903112337.4113-12-hdegoede@redhat.com
The pwm-crc code is using 2 different enable bits:
1. bit 7 of the PWM0_CLK_DIV (PWM_OUTPUT_ENABLE)
2. bit 0 of the BACKLIGHT_EN register
The BACKLIGHT_EN register at address 0x51 really controls a separate
output-only GPIO which is earmarked to be used as output connected to the
backlight-enable pin for LCD panels, this GPO is part of the PMIC's
"Display Panel Control Block." . This pin should probably be moved over
to a GPIO provider driver (and consumers modified accordingly), but that
is something for an(other) patch.
Enabling / disabling the actual PWM output is controlled by the
PWM_OUTPUT_ENABLE bit of the PWM0_CLK_DIV register.
As the comment in the old code already indicates we must disable the PWM
before we can change the clock divider. But the crc_pwm_disable() and
crc_pwm_enable() calls the old code make for this only change the
BACKLIGHT_EN register; and the value of that register does not matter for
changing the period / the divider. What does matter is that the
PWM_OUTPUT_ENABLE bit must be cleared before a new value can be written.
This commit modifies crc_pwm_config() to clear PWM_OUTPUT_ENABLE instead
when changing the period, so that period changes actually work.
Note this fix will cause a significant behavior change on some devices
using the CRC PWM output to drive their backlight. Before the PWM would
always run with the output frequency configured by the BIOS at boot, now
the period time specified by the i915 driver will actually be honored.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200903112337.4113-11-hdegoede@redhat.com
The CRC PWM controller has a clock-divider which divides the clock with
a value between 1-128. But as can seen from the PWM_DIV_CLK_xxx
defines, this range maps to a register value of 0-127.
So after calculating the clock-divider we must subtract 1 to get the
register value, unless the requested frequency was so high that the
calculation has already resulted in a (rounded) divider value of 0.
Note that before this fix, setting a period of PWM_MAX_PERIOD_NS which
corresponds to the max. divider value of 128 could have resulted in a
bug where the code would use 128 as divider-register value which would
have resulted in an actual divider value of 0 (and the enable bit being
set). A rounding error stopped this bug from actually happen. This
same rounding error means that after the subtraction of 1 it is impossible
to set the divider to 128. Also bump PWM_MAX_PERIOD_NS by 1 ns to allow
setting a divider of 128 (register-value 127).
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200903112337.4113-10-hdegoede@redhat.com
While looking into adding atomic-pwm support to the pwm-crc driver I
noticed something odd, there is a PWM_BASE_CLK define of 6 MHz and
there is a clock-divider which divides this with a value between 1-128,
and there are 256 duty-cycle steps.
The pwm-crc code before this commit assumed that a clock-divider
setting of 1 means that the PWM output is running at 6 MHZ, if that
is true, where do these 256 duty-cycle steps come from?
This would require an internal frequency of 256 * 6 MHz = 1.5 GHz, that
seems unlikely for a PMIC which is using a silicon process optimized for
power-switching transistors. It is way more likely that there is an 8
bit counter for the duty cycle which acts as an extra fixed divider
wrt the PWM output frequency.
The main user of the pwm-crc driver is the i915 GPU driver which uses it
for backlight control. Lets compare the PWM register values set by the
video-BIOS (the GOP), assuming the extra fixed divider is present versus
the PWM frequency specified in the Video-BIOS-Tables:
Device: PWM Hz set by BIOS PWM Hz specified in VBT
Asus T100TA 200 200
Asus T100HA 200 200
Lenovo Miix 2 8 23437 20000
Toshiba WT8-A 23437 20000
So as we can see if we assume the extra division by 256 then the register
values set by the GOP are an exact match for the VBT values, where as
otherwise the values would be of by a factor of 256.
This commit fixes the period / duty_cycle calculations to take the
extra division by 256 into account.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200903112337.4113-9-hdegoede@redhat.com
PWM controller drivers should not restore the PWM state on resume. The
convention is that PWM consumers do this by calling pwm_apply_state(),
so that it can be done at the exact moment when the consumer needs
the state to be stored, avoiding e.g. backlight flickering.
The only in kernel consumers of the pwm-lpss code, the i915 driver
and the pwm-class sysfs interface code both correctly restore the
state on resume, so there is no need to do this in the pwm-lpss code.
More-over the removed resume handler is buggy, since it blindly
restores the ctrl-register contents without setting the update
bit, which is necessary to get the controller to actually use/apply
the restored base-unit and on-time-div values.
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200903112337.4113-8-hdegoede@redhat.com
Before this commit pwm_lpss_apply() was assuming 2 pre-conditions
were met by the existing hardware state:
1. That the base-unit and on-time-div read back from the
control register are those actually in use, so that it
can skip setting the update bit if the read-back value
matches the desired values.
2. That the controller is enabled when the cached
pwm_state.enabled says that the controller is enabled.
As the long history of fixes for subtle (often suspend/resume)
lpss-pwm issues shows, these assumptions are not necessary
always true.
1. Specifically is not true on some (*) Cherry Trail devices
with a nasty GFX0._PS3 method which: a. saves the ctrl reg value.
b. sets the base-unit to 0 and writes the update bit to apply/commit
c. restores the original ctrl value without setting the update bit,
so that the 0 base-unit value is still in use.
2. Assumption 2. currently is true, but only because of the code which
saves/restores the state on suspend/resume. By convention restoring the
PWM state should be done by the PWM consumer and the presence of this
code in the pmw-lpss driver is a bug. Therefor the save/restore code will
be dropped in the next patch in this series, after which this assumption
also is no longer true.
This commit changes the pwm_lpss_apply() to not make any assumptions about
the state the hardware is in. Instead it makes pwm_lpss_apply() always
fully program the PWM controller, making it much less fragile.
*) Seen on the Acer One 10 S1003, Lenovo Ideapad Miix 310 and 320 models
and various Medion models.
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200903112337.4113-7-hdegoede@redhat.com
In the not-enabled -> enabled path pwm_lpss_apply() needs to get a
runtime-pm reference; and then on any errors it needs to release it
again.
This leads to somewhat hard to read code. This commit introduces a new
pwm_lpss_prepare_enable() helper and moves all the steps necessary for
the not-enabled -> enabled transition there, so that we can error check
the entire transition in a single place and only have one pm_runtime_put()
on failure call site.
While working on this I noticed that the enabled -> enabled (update
settings) path was quite similar, so I've added an enable parameter to
the new pwm_lpss_prepare_enable() helper, which allows using it in that
path too.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200903112337.4113-6-hdegoede@redhat.com
When the user requests a high enough period ns value, then the
calculations in pwm_lpss_prepare() might result in a base_unit value of 0.
But according to the data-sheet the way the PWM controller works is that
each input clock-cycle the base_unit gets added to a N bit counter and
that counter overflowing determines the PWM output frequency. Adding 0
to the counter is a no-op. The data-sheet even explicitly states that
writing 0 to the base_unit bits will result in the PWM outputting a
continuous 0 signal.
When the user requestes a low enough period ns value, then the
calculations in pwm_lpss_prepare() might result in a base_unit value
which is bigger then base_unit_range - 1. Currently the codes for this
deals with this by applying a mask:
base_unit &= (base_unit_range - 1);
But this means that we let the value overflow the range, we throw away the
higher bits and store whatever value is left in the lower bits into the
register leading to a random output frequency, rather then clamping the
output frequency to the highest frequency which the hardware can do.
This commit fixes both issues by clamping the base_unit value to be
between 1 and (base_unit_range - 1).
Fixes: 684309e504 ("pwm: lpss: Avoid potential overflow of base_unit")
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200903112337.4113-5-hdegoede@redhat.com
According to the data-sheet the way the PWM controller works is that
each input clock-cycle the base_unit gets added to a N bit counter and
that counter overflowing determines the PWM output frequency.
So assuming e.g. a 16 bit counter this means that if base_unit is set to 1,
after 65535 input clock-cycles the counter has been increased from 0 to
65535 and it will overflow on the next cycle, so it will overflow after
every 65536 clock cycles and thus the calculations done in
pwm_lpss_prepare() should use 65536 and not 65535.
This commit fixes this. Note this also aligns the calculations in
pwm_lpss_prepare() with those in pwm_lpss_get_state().
Note this effectively reverts commit 684309e504 ("pwm: lpss: Avoid
potential overflow of base_unit"). The next patch in this series really
fixes the potential overflow of the base_unit value.
Fixes: 684309e504 ("pwm: lpss: Avoid potential overflow of base_unit")
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200903112337.4113-4-hdegoede@redhat.com
With enhanced error reporting from cros_ec_cmd_xfer_status() in place,
we can fully use it and no longer rely on EC error codes.
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Since commit c5cd2b47b2 ("platform/chrome: cros_ec_proto: Report command
not supported") we can no longer assume that cros_ec_cmd_xfer_status()
reports -EPROTO for all errors returned by the EC itself. A follow-up
patch will change cros_ec_cmd_xfer_status() to report additional errors
reported by the EC as distinguished Linux error codes.
Handle this change by no longer assuming that only -EPROTO is used
to report all errors returned by the EC itself. Instead, support both
the old and the new error codes.
Add a comment describing cros_ec_num_pwms() to explain its functionality.
Cc: Gwendal Grignou <gwendal@chromium.org>
Cc: Yu-Hsuan Hsu <yuhsuan@chromium.org>
Cc: Prashant Malani <pmalani@chromium.org>
Cc: Brian Norris <briannorris@chromium.org>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
The plat-samsung directory and mach-s5pv210 can be build
completely independently, so split the two Kconfig symbols
CONFIG_PLAT_SAMSUNG and CONFIG_ARCH_S5PV210.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20200806182059.2431-18-krzk@kernel.org
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The majority of this batch is conversion of the PWM period and duty
cycle to 64-bit unsigned integers, which is required so that some types
of hardware can generate the full range of signals that they're capable
of. The remainder is mostly minor fixes and cleanups.
-----BEGIN PGP SIGNATURE-----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=v6MG
-----END PGP SIGNATURE-----
Merge tag 'pwm/for-5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"The majority of this batch is conversion of the PWM period and duty
cycle to 64-bit unsigned integers, which is required so that some
types of hardware can generate the full range of signals that they're
capable of.
The remainder is mostly minor fixes and cleanups"
* tag 'pwm/for-5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm:
pwm: bcm-iproc: handle clk_get_rate() return
pwm: Replace HTTP links with HTTPS ones
pwm: omap-dmtimer: Repair pwm_omap_dmtimer_chip's broken kerneldoc header
pwm: mediatek: Provide missing kerneldoc description for 'soc' arg
pwm: bcm-kona: Remove impossible comparison when validating duty cycle
pwm: bcm-iproc: Remove impossible comparison when validating duty cycle
pwm: iqs620a: Use lowercase hexadecimal literals for consistency
pwm: Convert period and duty cycle to u64
clk: pwm: Use 64-bit division function
backlight: pwm_bl: Use 64-bit division function
pwm: sun4i: Use nsecs_to_jiffies to avoid a division
pwm: sifive: Use 64-bit division macro
pwm: iqs620a: Use 64-bit division
pwm: imx27: Use 64-bit division macro
pwm: imx-tpm: Use 64-bit division macro
pwm: clps711x: Use 64-bit division macro
hwmon: pwm-fan: Use 64-bit division macro
drm/i915: Use 64-bit division macro
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Argument descriptions must be prepended with a '@' to be understood
by the kerneldoc tooling/parsers/validators.
Fixes the following W=1 warning:
drivers/pwm/pwm-omap-dmtimer.c:70: warning: Function parameter or member 'dm_timer_pdev' not described in 'pwm_omap_dmtimer_chip'
Cc: Tony Lindgren <tony@atomide.com>
Cc: Joachim Eastwood <manabian@gmail.com>
Cc: NeilBrown <neilb@suse.de>
Cc: Grant Erickson <marathon96@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Kerneldoc syntax is used, but not complete.
Descriptions are required for all arguments.
Fixes the following W=1 build warning:
drivers/pwm/pwm-mediatek.c:57: warning: Function parameter or member 'soc' not described in 'pwm_mediatek_chip'
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: John Crispin <blogic@openwrt.org>
Cc: Zhi Mao <zhi.mao@mediatek.com>
Cc: linux-pwm@vger.kernel.org
Cc: linux-mediatek@lists.infradead.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
'dc' here is an unsigned long, thus checking for <0 will always
evaluate to false.
Fixes the following W=1 warning:
drivers/pwm/pwm-bcm-kona.c:141:35: warning: comparison of unsigned expression < 0 is always false [-Wtype-limits]
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: linux-pwm@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
'duty' here is an unsigned int, thus checking for <0 will always
evaluate to false.
Fixes the following W=1 warning:
drivers/pwm/pwm-bcm-iproc.c:147:12: warning: comparison of unsigned expression < 0 is always false [-Wtype-limits]
Cc: Ray Jui <rjui@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: Yendapally Reddy Dhananjaya Reddy <yendapally.reddy@broadcom.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: linux-pwm@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The unicore32 port is removed from the kernel.
There is no point to keep stale PWM driver for this architecture.
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Other drivers use lowercase hexadecimal literals, so convert the IQS620a
driver to do the same for consistency.
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Because period and duty cycle are defined as ints with units of
nanoseconds, the maximum time duration that can be set is limited to
~2.147 seconds. Change their definitions to u64 in the structs of the
PWM framework so that higher durations may be set.
Also use the right format specifiers in debug prints in both core.c,
pwm-stm32-lp.c as well as video/fbdev/ssd1307fb.c.
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Guru Das Srinagesh <gurus@codeaurora.org>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Since the PWM framework is switching struct pwm_state.period's datatype
to u64, prepare for this transition by using nsecs_to_jiffies() which
does away with the need for a division operation.
Signed-off-by: Guru Das Srinagesh <gurus@codeaurora.org>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Since the PWM framework is switching struct pwm_args.period's datatype
to u64, prepare for this transition by using DIV64_U64_ROUND_CLOSEST to
handle a 64-bit divisor.
Signed-off-by: Guru Das Srinagesh <gurus@codeaurora.org>
Acked-by: Palmer Dabbelt <palmerdabbelt@google.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The PWM framework is going to change the PWM period and duty cycles to
be 64-bit unsigned integers. To avoid build errors on platforms that do
not natively support 64-bit division, use explicity 64-bit division.
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Since the PWM framework is switching struct pwm_state.period's
datatype to u64, prepare for this transition by using
DIV_ROUND_UP_ULL to handle a 64-bit dividend.
Signed-off-by: Guru Das Srinagesh <gurus@codeaurora.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Since the PWM framework is switching struct pwm_state.period's datatype
to u64, prepare for this transition by using DIV64_U64_ROUND_CLOSEST to
handle a 64-bit divisor.
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Signed-off-by: Guru Das Srinagesh <gurus@codeaurora.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Since the PWM framework is switching struct pwm_args.period's datatype
to u64, prepare for this transition by using DIV64_U64_ROUND_CLOSEST to
handle a 64-bit divisor.
Cc: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Guru Das Srinagesh <gurus@codeaurora.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The IS_ENABLED() use was missing the CONFIG_ prefix which would have
lead to skipping this code.
Fixes: 3ad1f3a332 ("pwm: Implement some checks for lowlevel drivers")
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
To not trigger the warnings provided by CONFIG_PWM_DEBUG
- use up-rounding in .get_state()
- don't divide by the result of a division
- don't use the rounded counter value for the period length to calculate
the counter value for the duty cycle
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The way state->enabled is computed is rather convoluted and hard to
read - both branches of the if() actually do the exact same thing. So
remove the if(), and further simplify "<boolean condition> ? true :
false" to "<boolean condition>".
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Even in failed case of pm_runtime_get_sync(), the usage_count is
incremented. In order to keep the usage_count with correct value call
appropriate pm_runtime_put().
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Added support for dynamic clock freq configuration in PWM kernel driver.
Earlier the PWM driver used to cache boot time clock rate by PWM clock
parent during probe. Hence dynamically changing PWM frequency was not
possible for all the possible ranges. With this change, dynamic
calculation is enabled and it is able to set the requested period from
sysfs knob provided the value is supported by clock source.
Changes mainly have 2 parts:
- Tegra186 and later chips [1]
- Tegra210 and prior chips [2]
For [1] - Changes implemented to set pwm period dynamically and also
checks added to allow only if requested period(ns) is below or
equals to higher range.
For [2] - Only checks if the requested period(ns) is below or equals to
higher range defined by max clock limit. The limitation in
Tegra210 or prior chips are due to the reason of having only
one PWM controller supporting multiple channels. But later
chips have multiple PWM controller instances each having
single channel support.
Signed-off-by: Sandipan Patra <spatra@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The PWM hardware in the JZ4725B works the same as in the JZ4740, but has
only six channels available.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The PWM in Ingenic SoCs starts in inactive state until the internal
timer reaches the duty value, then becomes active until the timer
reaches the period value. In theory, we should then use (period - duty)
as the real duty value, as a high duty value would otherwise result in
the PWM pin being inactive most of the time.
This is the reason why the duty value was inverted in the driver until
now, but it still had the problem that it would not start with the
active part.
To address this remaining issue, the common trick is to invert the
duty, and invert the polarity when the PWM is enabled.
Since the duty was already inverted, and we invert it again, we now
program the hardware for the requested duty, and simply invert the
polarity when the PWM is enabled.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Calculating the hardware value for the duty from the hardware value of
the period resulted in a precision loss versus calculating it from the
clock rate directly.
(Also remove a cast that doesn't really need to be here)
Fixes: f6b8a57000 ("pwm: Add Ingenic JZ4740 support")
Cc: <stable@vger.kernel.org>
Suggested-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Depending on MACH_INGENIC prevent us from creating a generic kernel that
works on more than one MIPS board. Instead, we just depend on MIPS being
set.
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Before commit cfc4c189bc ("pwm: Read initial hardware state at request
time"), a driver's get_state callback would get called once per PWM from
pwmchip_add().
pwm-lpss' runtime-pm code was relying on this, getting a runtime-pm ref for
PWMs which are enabled at probe time from within its get_state callback,
before enabling runtime-pm.
The change to calling get_state at request time causes a number of
problems:
1. PWMs enabled at probe time may get runtime suspended before they are
requested, causing e.g. a LCD backlight controlled by the PWM to turn off.
2. When the request happens when the PWM has been runtime suspended, the
ctrl register will read all 1 / 0xffffffff, causing get_state to store
bogus values in the pwm_state.
3. get_state was using an async pm_runtime_get() call, because it assumed
that runtime-pm has not been enabled yet. If shortly after the request an
apply call is made, then the pwm_lpss_is_updating() check may trigger
because the resume triggered by the pm_runtime_get() call is not complete
yet, so the ctrl register still reads all 1 / 0xffffffff.
This commit fixes these issues by moving the initial pm_runtime_get() call
for PWMs which are enabled at probe time to the pwm_lpss_probe() function;
and by making get_state take a runtime-pm ref before reading the ctrl reg.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1828927
Fixes: cfc4c189bc ("pwm: Read initial hardware state at request time")
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Allwinner A64 is capable of a direct clock output on PWM (see A64 User
Manual chapter 3.10). Add support for this in the sun4i PWM driver.
Signed-off-by: Peter Vasil <peter.vasil@gmail.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
This patch adds support for the Azoteq IQS620A, capable of generating
a 1-kHz PWM output with duty cycle between ~0.4% and 100% (inclusive).
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Message logged by 'dev_xxx()' or 'pr_xxx()' should end with a '\n'.
Fixes: 3ad1f3a332 ("pwm: Implement some checks for lowlevel drivers")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
This driver allows pwms to be requested as gpios via gpiolib. Obviously,
it should not be allowed to request a GPIO when its corresponding PWM is
already requested (and vice versa). So it requires some exclusion code.
Given that the PWMm and GPIO cores are not synchronized with respect to
each other, this exclusion code will also require proper
synchronization.
Such a mechanism was in place, but was inadvertently removed by Uwe's
clean-up in commit e926b12c61 ("pwm: Clear chip_data in pwm_put()").
Upon revisiting the synchronization mechanism, we found that
theoretically, it could allow two threads to successfully request
conflicting PWMs/GPIOs.
Replace with a bitmap which tracks PWMs in-use, plus a mutex. As long as
PWM and GPIO's respective request/free functions modify the in-use
bitmap while holding the mutex, proper synchronization will be
guaranteed.
Reported-by: YueHaibing <yuehaibing@huawei.com>
Fixes: e926b12c61 ("pwm: Clear chip_data in pwm_put()")
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: YueHaibing <yuehaibing@huawei.com>
Link: https://lkml.org/lkml/2019/5/31/963
Signed-off-by: Sven Van Asbroeck <TheSven73@gmail.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
[cg: Tested on an i.MX6Q board with two NXP PCA9685 chips]
Tested-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Reviewed-by: Sven Van Asbroeck <TheSven73@gmail.com> # cg's rebase
Link: https://lore.kernel.org/lkml/20200330160238.GD2817345@ulmo/
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Fix the following gcc warning:
drivers/pwm/core.c:467:6: warning: symbol 'pwm_apply_state_debug' was
not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The variable fin_freq is being initialized with a value that is never
read and it is being updated later with a new value. The initialization
is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The TCU channels 0 and 1 were previously reserved for system tasks, and
thus unavailable for PWM.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Mathieu Malaterre <malat@debian.org>
Tested-by: Artur Rojek <contact@artur-rojek.eu>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The TCU registers are shared between a handful of drivers, accessing
them through the same regmap.
While this driver is devicetree-compatible, it is never (as of now)
probed from devicetree, so this change does not introduce a ABI problem
with current devicetree files.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Mathieu Malaterre <malat@debian.org>
Tested-by: Artur Rojek <contact@artur-rojek.eu>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The previous algorithm hardcoded details about how the TCU clocks work.
The new algorithm will use clk_round_rate to find the perfect clock rate
for the PWM channel.
This code relies on the fact that clk_round_rate() will always round
down, which is not a valid assumption given by the clk API, but only
happens to be true with the clk drivers used for Ingenic SoCs.
Right now, there is no alternative as the clk API does not have a
round-down function (and won't have one for a while), but if it ever
comes to light, a round-down function should be used instead.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Mathieu Malaterre <malat@debian.org>
Tested-by: Artur Rojek <contact@artur-rojek.eu>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The ingenic-timer "TCU" driver provides us with clocks, that can be
(un)gated, reparented or reclocked from devicetree, instead of having
these settings hardcoded in this driver.
The new code now uses a clk pointer per PWM (instead of a clk per
pwm-chip before). So the pointer is stored in per-pwm data now.
The calls to arch-specific timer code is replaced with standard
clock API calls to start and stop each channel's clock.
While this driver is devicetree-compatible, it is never (as of now)
probed from devicetree, so this change does not introduce a ABI problem
with current devicetree files.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Mathieu Malaterre <malat@debian.org>
Tested-by: Artur Rojek <contact@artur-rojek.eu>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
'needs_delay' does now always evaluate to true, so remove all
occurrences.
Signed-off-by: Pascal Roeleven <dev@pascalroeleven.nl>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Implement .apply callback and drop the legacy callbacks(enable, disable,
config, set_polarity). In .apply() check for the current hardware status
before changing the PWM configuration.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Only the Timer control register(TCLR) cannot be updated when the timer
is running. Registers like Counter register (TCRR), loader register
(TLDR) and match register (TMAR) can be updated while the counter is
running. Since TCLR is not updated in pwm_omap_dmtimer_config(), do not
stop the timer for period/duty_cycle update.
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
To configure DM timer in PWM mode the following needs to be set in
OMAP_TIMER_CTRL_REG using set_pwm callback:
- Set toggle mode on PORTIMERPWM output pin
- Set trigger on overflow and match on PORTIMERPWM output pin.
- Set auto reload
This is a one time configuration and needs to be set before the start of
the DM timer. But the current driver tries to set the same configuration
for every period/duty cycle update, which is not needed. So move the PWM
setup before enabling timer and do not update it in
pwm_omap_dmtimer_config().
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Update the description with a brief about how PWM is generated using
OMAP DM timer and add limitations for the PWM generations. Also add a
link to the reference manual.
Suggested-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
pwm_omap_dmtimer.h is used only:
- to typedef struct omap_dm_timer to pwm_omap_dmtimer
- for macro PWM_OMAP_DMTIMER_TRIGGER_OVERFLOW_AND_COMPARE
Rest of the file is pretty mush unsed. So reuse omap_dm_timer
and OMAP_TIMER_TRIGGER_OVERFLOW_AND_COMPARE in pwm-omap-dmtimer.c
and delete the header file.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
During device probe, the message
TPU PWM -1 registered
is printed.
While the "-1" looks suspicious, it is perfectly normal for a device
instantiated from DT.
Remove the message, as there are no non-DT users left, and other drivers
don't print such messages either.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Runtime PM should be enabled before calling pwmchip_add(), as PWM users
can appear immediately after the PWM chip has been added.
Likewise, Runtime PM should always be disabled after the removal of the
PWM chip, even if the latter failed.
Fixes: 99b82abb0a ("pwm: Add Renesas TPU PWM driver")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Runtime PM should be enabled before calling pwmchip_add(), as PWM users
can appear immediately after the PWM chip has been added.
Likewise, Runtime PM should be disabled after the removal of the PWM
chip.
Fixes: ed6c1476bf ("pwm: Add support for R-Car PWM Timer")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
GPIO core recently added macro to uniformly specify direction of a GPIO
line, so use it.
Signed-off-by: Rishi Gupta <gupt21@gmail.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The __maybe_unused attribute is preferred over CONFIG_PM to prevent
potential build time issues. This commit replaces CONFIG_PM with this
attribute.
Signed-off-by: Rishi Gupta <gupt21@gmail.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Tegra194 has multiple PWM controllers with each having only one output.
Also the maxmimum frequency is higher than earlier SoCs.
Add support for Tegra194 and specify the number of PWM outputs and
maximum supported frequency using device tree match data.
Signed-off-by: Sandipan Patra <spatra@nvidia.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Some of the PWM drivers can be compile tested to increase build
coverage.
The Meson PWM driver requires COMMON_CLK dependency.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com> # For Broadcoam
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> # For Meson
Acked-by: Claudiu Beznea <claudiu.beznea@microchip.com> # For Atmel
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
duty_cycle was only set, never read.
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
There is nothing in use from of_address.h, remove it.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
There is nothing in use from of_device.h, remove it.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
There is nothing in use from log2.h/of_address.h, remove them.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
There are some expectations which the callbacks provided by lowlevel
drivers should fulfill. Implement checks that help driver authors to get
these semantics right. As these have some overhead the checks can be
disabled using a Kconfig setting.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Up to now the .probe() function didn't enable clocks and relied on the
core to call the .get_state() callback to have the clock running. The
latter enabled the needed clocks and kept them running if the PWM wass
enabled.
This only works correctly if the .get_state() callback is called exactly
once and this single call happens before unused clocks are disabled by
the clk core.
The former wasn't true for a short period while commit 01ccf903ed
("pwm: Let pwm_get_state() return the last implemented state") applied
and not reverted yet and might become wrong in the future.
The latter isn't true any more since commit cfc4c189bc ("pwm: Read
initial hardware state at request time") which results in a running PWM
being stopped at boot time if for example the consumer lives in a kernel
module that is only loaded after the clk core disabled unused clocks.
So ensure .probe() is left with the clocks on if the PWM is running and
.get_state() disables everything it enabled.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The .remove() callback is not supposed to modify hardware state. This is
in the responsibility of the PWM consumer.
After the PWM was disabled the clocks are off (apart from a bug that is
fixed in the next patch), so unbinding the driver either stops the PWM
(which it should not) or disables already disabled clocks yielding
warnings from the clk core.
So just drop the call to disable the clocks. (Which BTW was also in the
wrong order because the call makes the PWM unfunctional and so should
have come only after pwmchip_remove()).
Fixes: 9f4c8f9607 ("pwm: imx: Add ipg clock operation")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
pwm_imx27_clk_prepare_enable() took a pointer to a struct pwm_chip just
to convert it to a struct pwm_imx27_chip pointer while all callers
already have the latter. Ditto for pwm_imx27_clk_disable_unprepare().
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
pwm_imx27_apply() enables the clocks if the previous PWM state was
disabled. Given that the clocks are supposed to be left on iff the PWM
is running, the decision to disable the clocks at the end of the
function must not depend on the previous state.
Without this fix the enable count of the two affected clocks increases
by one whenever ->apply() changes from one disabled state to another.
Fixes: bd88d319ab ("pwm: imx27: Unconditionally write state to hardware")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The newer 2711 and 7211 chips have two PWM controllers and failure to
dynamically allocate the PWM base would prevent the second PWM
controller instance being probed for succeeding with an -EEXIST error
from alloc_pwms().
Fixes: e5a06dc5ac ("pwm: Add BCM2835 PWM driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
dm timer ops set_load() api allows to configure the load value and to
set the auto reload feature. But auto reload feature is independent of
load value and should be part of configuring pwm. This way pwm can be
disabled by disabling auto reload feature using set_pwm() so that the
current pwm cycle will be completed. Else pwm disabling causes the
cycle to be stopped abruptly.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200305082715.15861-7-lokeshvutla@ti.com
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/pwm/pwm-pca9685.c: In function ‘pca9685_pwm_gpio_free’:
drivers/pwm/pwm-pca9685.c:162:21: warning: variable ‘pwm’ set but not used [-Wunused-but-set-variable]
It is never used, and so can be removed. In that case, hold and release
the lock 'pca->lock' can be removed since nothing will be done between
them.
Fixes: e926b12c61 ("pwm: Clear chip_data in pwm_put()")
Signed-off-by: yu kuai <yukuai3@huawei.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
GCC can't always determine that the duty, period and prescaler values
are initialized when returning from sun4i_pwm_calculate(), so help out a
little by initializing them to 0.
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Don't use AOE (automatic output enable) by default. In case of break
events, PWM is automatically re-enabled on next PWM cycle otherwise.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The variable pval is only used in a single block in the function
sun4i_pwm_calculate(). So declare it in a more local scope to simplify
the function for humans and compilers.
While at it also simplify assignment to pval.
While the diffstat for this patch is negative for this patch I still
thing the advantage of having a narrower scope is beneficial.
In my compiler / .config setup (gcc 8.2.1, arm/imx_v6_v7_defconfig +
COMPILE_TEST + PWM_SUN4I) this change doesn't result in any binary
changes.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
BCM7211 is supported using ARCH_BRCMSTB and uses this PWM controller
driver, make it possible to build it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
For defer probe error, no need to output error message which
will cause confusion.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Fix inconsistent IS_ERR and PTR_ERR in sun4i_pwm_probe().
The proper pointers to be passed as arguments are pwm->clk and pwm->bus_clk.
This bug was detected with the help of Coccinelle.
Fixes: b8d74644f3 ("pwm: sun4i: Prefer "mod" clock to unnamed")
Fixes: 5b090b430d ("pwm: sun4i: Add an optional probe for bus clock")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
pwm_calculate() calls clk_get_rate() while holding a spin_lock().
This create an issue as clk_get_rate() may sleep.
Move pwm_calculate() out of this spin_lock().
Fixes: c32c5c50d4 ("pwm: sun4i: Switch to atomic PWM")
Reported-by: Alexander Finger <alex.mobigo@gmail.com>
Sugested-by: Vasily Khoruzhick <anarsoul@gmail.com>
Tested-by: Alexander Finger <alex.mobigo@gmail.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The dependency on OMAP_DM_TIMER is only a runtime dependency. Also
OMAP_DM_TIMER cannot be enabled without ARCH_OMAP being enabled.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
This was found by coccicheck:
drivers/pwm/pwm-omap-dmtimer.c:304:2-8: ERROR: missing put_device;
call of_find_device_by_node on line 255, but without a corresponding
object release within this function.
Reported-by: Markus Elfring <elfring@users.sourceforge.net>
Fixes: 6604c6556d ("pwm: Add PWM driver for OMAP using dual-mode timers")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Instead of doing error handling in the middle of ->probe(), move error
handling and freeing the reference to timer to the end.
This fixes a resource leak as dm_timer wasn't freed when allocating
*omap failed.
Implementation note: The put: label was never reached without a goto and
ret being unequal to 0, so the removed return statement is fine.
Fixes: 6604c6556d ("pwm: Add PWM driver for OMAP using dual-mode timers")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
In the old code (e.g.) mutex_destroy() was called before
pwmchip_remove(). Between these two calls it is possible that a PWM
callback is used which tries to grab the mutex.
Fixes: 6604c6556d ("pwm: Add PWM driver for OMAP using dual-mode timers")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
This allows to log all calls to the driver's lowlevel functions which
simplifies debugging in some cases.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
When .apply() is called with state->duty_cycle = 0 the duty_ns parameter
to rcar_pwm_set_counter() is 0 which results in ph being 0 and
rcar_pwm_set_counter() returning -EINVAL.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
pwm_get_state has no side effects and the resulting pwm_state is unused.
So drop the call to pwm_get_state() and the local variable from
rcar_pwm_apply().
The call was introduced in commit 7f68ce8287 ("pwm: rcar: Add support
"atomic" API") and already then was useless.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
This function reads back the configured parameters from the hardware. As
.apply() rounds down (mostly) I'm rounding up in .get_state() to achieve
that applying a state just read from hardware is a no-op.
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Acked-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
This makes it a bit easier when instrumenting register access to only
have to add code in one place.
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
This documents the my findings while reading through the driver and the
reference manual.
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The calculated values are the same with the modified algorithm. The only
difference is that the calculation is a bit more efficient.
Acked-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The maximal prescale value is 10 for all supported variants. So drop the
member in the variant description and introduce a global constant
instead.
This reduces the size of the variant descriptions and the .apply()
callback can be compiled a bit more effectively.
Acked-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Most Microchip (formerly Atmel) chips have publicly available manuals.
A comprehensive list is already contained in the documentation folder.
Reference this list in the header of the driver to allow reviewers to
find the relevant manuals.
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Since the divisor is not a compile-time constant (unless gcc somehow
decided to unroll the loop PERIOD_CDIV_MAX times), this does a
somewhat expensive 32/32 division. Replace that with a right shift.
We still have a 64/32 division just below, but at least in that
case the divisor is compile-time constant.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
If I'm reading of_pwm_xlate_with_flags() right, existing device trees
that set #pwm-cells = 2 will continue to work.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Since we now have ->apply(), these are no longer relevant.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
In preparation for supporting setting the polarity, switch the driver
to support the ->apply() method.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Now that sun4i PWM driver supports deasserting reset line and enabling
bus clock, support for H6 PWM can be added.
Note that while H6 PWM has two channels, only first one is wired to
output pin. Second channel is used as a clock source to companion AC200
chip which is bundled into same package.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
PWM core has an option to bypass whole logic and output unchanged source
clock as PWM output. This is achieved by enabling bypass bit.
Note that when bypass is enabled, no other setting has any meaning, not
even enable bit.
This mode of operation is needed to achieve high enough frequency to
serve as clock source for AC200 chip which is integrated into same
package as H6 SoC.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Bypass mode will require to be re-calculated when the pwm state
is changed.
Remove the condition so pwm_sun4i_calculate is always called.
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
H6 PWM core needs bus clock to be enabled in order to work.
Add an optional probe for it.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
New device tree bindings called the source clock of the module
"mod" when several clocks are defined.
Try to get a clock called "mod" if nothing is found try to get
an unnamed clock.
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
H6 PWM core needs deasserted reset line in order to work.
Add an optional probe for it.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The i.MX driver currently uses a shortcut and doesn't write all of the
state through to the hardware when the PWM is disabled. This causes an
inconsistent state to be read back by consumers with the result of them
malfunctioning.
Fix this by always writing the full state through to the hardware
registers so that the correct state can always be read back.
Tested-by: Michal Vokáč <michal.vokac@ysoft.com>
Tested-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The hardware register containing the duty cycle value cannot be accessed
when the PWM is disabled. This causes the ->get_state() callback to read
back a duty cycle value of 0, which can confuse consumer drivers.
Tested-by: Michal Vokáč <michal.vokac@ysoft.com>
Tested-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The ChromeOS embedded controller doesn't differentiate between disabled
and duty cycle being 0. In order not to potentially confuse consumers,
cache the duty cycle and return the cached value instead of the real
value when the PWM is disabled.
Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Drivers that support reading the hardware state (using ->get_state())
may want to rely on per-PWM data to do so. Defer reading the hardware
state for the first time until the PWM has been requested and after
drivers have had a chance to allocate per-PWM data.
Conceptually this is also a more natural place to read the hardware
state because the PWM core doesn't need to know the hardware state of a
PWM unless there is a user for it. This also ensures that the state is
read everytime a user requests a PWM. If the PWM changes between users
for some reason, the PWM core will reload the state from hardware and
keep its copy of the state up-to-date.
Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Michal Vokáč <michal.vokac@ysoft.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Various changes and minor fixes across a couple of drivers.
-----BEGIN PGP SIGNATURE-----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=Sd9F
-----END PGP SIGNATURE-----
Merge tag 'pwm/for-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"Various changes and minor fixes across a couple of drivers"
* tag 'pwm/for-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm:
pwm: stm32: Pass breakinput instead of its values
pwm: stm32: Remove clutter from ternary operator
pwm: stm32: Validate breakinput data from DT
pwm: Update comment on struct pwm_ops::apply
pwm: sun4i: Fix incorrect calculation of duty_cycle/period
pwm: stm32: Add power management support
pwm: stm32: Split breakinput apply routine to ease PM support
dt-bindings: pwm-stm32: Document pinctrl sleep state
pwm: sun4i: Drop redundant assignment to variable pval
dt-bindings: pwm: mediatek: Remove gratuitous compatible string for MT7629
The owner member of struct pwm_ops must be set to THIS_MODULE to
increase the reference count of the module such that the module cannot
be removed while its code is in use.
Fixes: daa5abc41c ("pwm: Add support for Broadcom iProc PWM controller")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Remove usage of the ternary operator to assign values for register
fields. Instead, parameterize the register and field offset macros
and pass the index to them.
This removes clutter and improves readability.
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Both index and level can only be either 0 or 1 and the filter value is
limited to values between (and including) 0 and 15. Validate that the
device tree node contains values that are within these ranges.
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Since 5.4-rc1, pwm_apply_state calls ->get_state after ->apply
if available, and this revealed an issue with integer precision
when calculating duty_cycle and period for the currently set
state in ->get_state callback.
This issue manifested in broken backlight on several Allwinner
based devices.
Previously this worked, because ->apply updated the passed state
directly.
Fixes: deb9c462f4 ("pwm: sun4i: Don't update the state for the caller of pwm_apply_state")
Signed-off-by: Ondrej Jirman <megous@megous.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Add suspend/resume PM sleep ops. When going to low power, enforce the PWM
channel isn't active. Let the PWM consumers disable it during their own
suspend sequence, see [1]. So, perform a check here, and handle the
pinctrl states. Also restore the break inputs upon resume, as registers
content may be lost when going to low power mode.
[1] https://lkml.org/lkml/2019/2/5/770
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Split breakinput routine that configures STM32 timers 'break' safety
feature upon probe, into two routines:
- stm32_pwm_apply_breakinputs() sets all the break inputs into registers.
- stm32_pwm_probe_breakinputs() probes the device tree break input settings
before calling stm32_pwm_apply_breakinputs()
This is a precursor patch to ease PM support. Registers content may get
lost during low power. So, break input settings applied upon probe need
to be restored upon resume (e.g. by calling stm32_pwm_apply_breakinputs()).
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Variable pval is being assigned a value that is never read. The
assignment is redundant and hence can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
It turns out that commit 01ccf903ed ("pwm: Let pwm_get_state() return
the last implemented state") causes backlight failures on a number of
boards. The reason is that some of the drivers do not write the full
state through to the hardware registers, which means that ->get_state()
subsequently does not return the correct state. Consumers which rely on
pwm_get_state() returning the current state will therefore get confused
and subsequently try to program a bad state.
Before this change can be made, existing drivers need to be more
carefully audited and fixed to behave as the framework expects. Until
then, keep the original behaviour of returning the software state that
was applied rather than reading the state back from hardware.
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Michal Vokáč <michal.vokac@ysoft.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The TI PWMSS driver is a simple bus driver for providing power
power management for the PWM peripherals on TI AM33xx SoCs, namely
eCAP, eHRPWM and eQEP. The eQEP is a counter rather than a PWM, so
it does not make sense to have the bus driver in the PWM subsystem
since the PWMSS is not exclusive to PWM devices.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Besides one new driver being added for the PWM controller found in
various Spreadtrum SoCs, this series of changes brings a slew of, mostly
minor, fixes and cleanups for existing drivers, as well as some
enhancements to the core code.
Lastly, Uwe is added to the PWM subsystem entry of the MAINTAINERS file,
making official his role as a reviewer.
-----BEGIN PGP SIGNATURE-----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=C9sW
-----END PGP SIGNATURE-----
Merge tag 'pwm/for-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"Besides one new driver being added for the PWM controller found in
various Spreadtrum SoCs, this series of changes brings a slew of,
mostly minor, fixes and cleanups for existing drivers, as well as some
enhancements to the core code.
Lastly, Uwe is added to the PWM subsystem entry of the MAINTAINERS
file, making official his role as a reviewer"
* tag 'pwm/for-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (34 commits)
MAINTAINERS: Add myself as reviewer for the PWM subsystem
MAINTAINERS: Add patchwork link for PWM entry
MAINTAINERS: Add a selection of PWM related keywords to the PWM entry
pwm: mediatek: Add MT7629 compatible string
dt-bindings: pwm: Update bindings for MT7629 SoC
pwm: mediatek: Update license and switch to SPDX tag
pwm: mediatek: Use pwm_mediatek as common prefix
pwm: mediatek: Allocate the clks array dynamically
pwm: mediatek: Remove the has_clks field
pwm: mediatek: Drop the check for of_device_get_match_data()
pwm: atmel: Consolidate driver data initialization
pwm: atmel: Remove unneeded check for match data
pwm: atmel: Remove platform_device_id and use only dt bindings
pwm: stm32-lp: Add check in case requested period cannot be achieved
pwm: Ensure pwm_apply_state() doesn't modify the state argument
pwm: fsl-ftm: Don't update the state for the caller of pwm_apply_state()
pwm: sun4i: Don't update the state for the caller of pwm_apply_state()
pwm: rockchip: Don't update the state for the caller of pwm_apply_state()
pwm: Let pwm_get_state() return the last implemented state
pwm: Introduce local struct pwm_chip in pwm_apply_state()
...
This adds pwm support for MT7629, and separate mt7629 compatible string
from mt7622
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Add SPDX identifiers to pwm-mediatek.c. Update MODULE_LICENSE to
correctly reflect the GNU General Public License v2.0.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Use pwm_mediatek as common prefix to match the filename. No functional
change intended.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Yangtao Li
Uwe Kleine-König
Linus Torvalds
Jarkko Nikula
Hauke Mehrtens
David Jander
Krzysztof Kozlowski
Liu Shixin
Simon South
Michael Walle
Rodrigo Vivi
Hans de Goede
Guenter Roeck
Arnd Bergmann
Rayagonda Kokatanur
Alexander A. Klimov
Lee Jones
Mike Rapoport
Thierry Reding
Guru Das Srinagesh
Kees Cook
Rasmus Villemoes
Navid Emamdoost
Sandipan Patra
Paul Cercueil
Peter Vasil
Jeff LaBundy
Christophe JAILLET
Sven Van Asbroeck
Jason Yan
Colin Ian King
Pascal Roeleven
Lokesh Vutla
Geert Uytterhoeven
Rishi Gupta
Matthias Schiffer
Anson Huang
Florian Fainelli
yu kuai
Fabrice Gasnier
Gustavo A. R. Silva
Clément Péron
Uwe Kleine-König
Jernej Skrabec
Greg Kroah-Hartman
Ondrej Jirman
David Lechner
Sam Shih