The TI K3 family of SoCs typically have one or more dual-core Arm Cortex
R5F processor clusters/subsystems (R5FSS). This R5F subsystem/cluster
can be configured at boot time to be either run in a LockStep mode or in
an Asymmetric Multi Processing (AMP) fashion in Split-mode. This subsystem
has 64 KB each Tightly-Coupled Memory (TCM) internal memories for each
core split between two banks - TCMA and TCMB (further interleaved into
two banks). The subsystem does not have an MMU, but has a Region Address
Translater (RAT) module that is accessible only from the R5Fs for providing
translations between 32-bit CPU addresses into larger system bus addresses.
Add a remoteproc driver to support this subsystem to be able to load and
boot the R5F cores primarily in LockStep mode. The code also includes the
base support for Split mode. Error Recovery and Power Management features
are not currently supported. Loading support includes the internal TCMs
and DDR. RAT support is left for a future patch, and as such the reserved
memory carveout regions are all expected to be using memory regions within
the first 2 GB.
The R5F remote processors do not have an MMU, and so require fixed memory
carveout regions matching the firmware image addresses. Support for this
is provided by mandating multiple memory regions to be attached to the
remoteproc device. The first memory region will be used to serve as the
DMA pool for all dynamic allocations like the vrings and vring buffers.
The remaining memory regions are mapped into the kernel at device probe
time, and are used to provide address translations for firmware image
segments without the need for any RSC_CARVEOUT entries. Any firmware
image using memory outside of the supplied reserved memory carveout
regions will be errored out.
The R5F processors on TI K3 SoCs require a specific sequence for booting
and shutting down the processors. This sequence is also dependent on the
mode (LockStep or Split) the R5F cluster is configured for. The R5F cores
have a Memory Protection Unit (MPU) that has a default configuration that
does not allow the cores to run out of DDR out of reset. This is resolved
by using the TCMs for boot-strapping code that applies the appropriate
executable permissions on desired DDR memory. The loading into the TCMs
requires that the resets be released first with the cores in halted state.
The Power Sleep Controller (PSC) module on K3 SoCs requires that the cores
be in WFI/WFE states with no active bus transactions before the cores can
be put back into reset. Support for this is provided by using the newly
introduced .prepare() and .unprepare() ops in the remoteproc core. The
.prepare() ops is invoked before any loading, and the .unprepare() ops
is invoked after the remoteproc resource cleanup. The R5F core resets
are deasserted in .prepare() and asserted in .unprepare(), and the cores
themselves are started and halted in .start() and .stop() ops. This
ensures symmetric usage and allows the R5F cores state machine to be
maintained properly between using the sysfs 'state' variable, bind/unbind
and regular module load/unload flows.
The subsystem is represented as a single remoteproc in LockStep mode, and
as two remoteprocs in Split mode. The driver uses various TI-SCI interfaces
to talk to the System Controller (DMSC) for managing configuration, power
and reset management of these cores. IPC between the A53 cores and the R5
cores is supported through the virtio rpmsg stack using shared memory and
OMAP Mailboxes.
The AM65x SoCs typically have a single R5FSS in the MCU voltage domain. The
J721E SoCs uses a slightly revised IP and typically have three R5FSSs, with
one cluster present within the MCU voltage domain (MCU_R5FSS0), and the
remaining two clusters present in the MAIN voltage domain (MAIN_R5FSS0 and
MAIN_R5FSS1). The integration of these clusters on J721E SoC is also
slightly different in that these IPs do support an actual local reset line,
while they are a no-op on AM65x SoCs.
Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20201002234234.20704-3-s-anna@ti.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Split out all the bits that are purely for dma_map_ops implementations
and related code into a new <linux/dma-map-ops.h> header so that they
don't get pulled into all the drivers. That also means the architecture
specific <asm/dma-mapping.h> is not pulled in by <linux/dma-mapping.h>
any more, which leads to a missing includes that were pulled in by the
x86 or arm versions in a few not overly portable drivers.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Fix the discrepancy observed between accepted input and read back value
while disabling remoteproc coredump through the coredump debugfs entry.
Fixes: 3afdc59e43 ("remoteproc: Add coredump debugfs entry")
Cc: stable@vger.kernel.org
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/20200916145100.15872-1-sibis@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
On secure devices which support warm reset, the MBA firmware requires
access to the modem region to clear them out. Hence provide Q6 access
to this region before MBA boot. This will be a nop during a modem SSR.
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/20200917175840.18708-1-sibis@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Currently when pointer scp is null a dev_err is being called that
references the pointer which is the very thing we are trying to
avoid doing. Remove the extraneous error message to avoid this
issue.
Addresses-Coverity: ("Dereference after null check")
Fixes: 63c13d61ea ("remoteproc/mediatek: add SCP support for mt8183")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20200918152428.27258-1-colin.king@canonical.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The new field 'dma_range_map' in struct device is used to facilitate the
use of single or multiple offsets between mapping regions of cpu addrs and
dma addrs. It subsumes the role of "dev->dma_pfn_offset" which was only
capable of holding a single uniform offset and had no region bounds
checking.
The function of_dma_get_range() has been modified so that it takes a single
argument -- the device node -- and returns a map, NULL, or an error code.
The map is an array that holds the information regarding the DMA regions.
Each range entry contains the address offset, the cpu_start address, the
dma_start address, and the size of the region.
of_dma_configure() is the typical manner to set range offsets but there are
a number of ad hoc assignments to "dev->dma_pfn_offset" in the kernel
driver code. These cases now invoke the function
dma_direct_set_offset(dev, cpu_addr, dma_addr, size).
Signed-off-by: Jim Quinlan <james.quinlan@broadcom.com>
[hch: various interface cleanups]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Tested-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Tested-by: Nathan Chancellor <natechancellor@gmail.com>
Fix the assignment of the @state pointer - it is obviously wrong.
Acked-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Fixes: 376ffdc044 ("remoteproc: stm32: Properly set co-processor state when attaching")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20200831213758.206690-1-mathieu.poirier@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This introduces a new "detached" state for remote processors that are
deemed to be running at the time Linux boots and the infrastructure for
"attaching" to these. It then introduces the support for performing this
operation for the STM32 platform.
The coredump functionality is moved out from the core file and gains
support for an optional mode where the recovery phase awaits the
notification from devcoredump that the dump should be released. This
allows userspace to grab the coredump in scenarios where vmalloc space
is too low for creating a complete copy of the coredump before handing
this to devcoredump.
A new character device based interface is introduced to allow tying the
stoppage of a remote processor to the termination of a user space
process. This is useful in situations when such process provides crucial
resources/operations for the firmware running on the remote processor.
The Texas Instrument K3 driver gains support for the C66x and C71x DSPs.
Qualcomm remoteprocs gains support for stashing relocation information
in IMEM, to aid post mortem debugging and the crash notification
mechanism is generalized to be reusable in cases where loosely coupled
drivers needs to know about the status of a remote processor. One such
example is the IPA hardware block, which is jointly owned with the
modem and migrated to this improved interface.
It also introduces a number of bug fixes and debug improvements for the
Qualcomm modem remoteproc driver.
And it cleans up the inconsistent interface for remoteproc drivers to
implement power management.
-----BEGIN PGP SIGNATURE-----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=9cjt
-----END PGP SIGNATURE-----
Merge tag 'rproc-v5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/andersson/remoteproc
Pull remoteproc updates from Bjorn Andersson:
"This introduces a new "detached" state for remote processors that are
deemed to be running at the time Linux boots and the infrastructure
for "attaching" to these. It then introduces the support for
performing this operation for the STM32 platform.
The coredump functionality is moved out from the core file and gains
support for an optional mode where the recovery phase awaits the
notification from devcoredump that the dump should be released. This
allows userspace to grab the coredump in scenarios where vmalloc space
is too low for creating a complete copy of the coredump before handing
this to devcoredump.
A new character device based interface is introduced to allow tying
the stoppage of a remote processor to the termination of a user space
process. This is useful in situations when such process provides
crucial resources/operations for the firmware running on the remote
processor.
The Texas Instrument K3 driver gains support for the C66x and C71x
DSPs.
Qualcomm remoteprocs gains support for stashing relocation information
in IMEM, to aid post mortem debugging and the crash notification
mechanism is generalized to be reusable in cases where loosely coupled
drivers needs to know about the status of a remote processor. One such
example is the IPA hardware block, which is jointly owned with the
modem and migrated to this improved interface.
It also introduces a number of bug fixes and debug improvements for
the Qualcomm modem remoteproc driver.
And it cleans up the inconsistent interface for remoteproc drivers to
implement power management"
* tag 'rproc-v5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/andersson/remoteproc: (56 commits)
remoteproc: core: Register the character device interface
remoteproc: Add remoteproc character device interface
remoteproc: kill IPA notify code
net: ipa: new notification infrastructure
remoteproc: k3-dsp: Add support for C71x DSPs
dt-bindings: remoteproc: k3-dsp: Update bindings for C71x DSPs
remoteproc: k3-dsp: Add support for L2RAM loading on C66x DSPs
remoteproc: k3-dsp: Add a remoteproc driver of K3 C66x DSPs
dt-bindings: remoteproc: Add bindings for C66x DSPs on TI K3 SoCs
remoteproc: k3: Add TI-SCI processor control helper functions
remoteproc: Introduce rproc_of_parse_firmware() helper
dt-bindings: arm: keystone: Add common TI SCI bindings
remoteproc: qcom_q6v5_mss: Remove redundant running state
remoteproc: qcom: q6v5: Update running state before requesting stop
remoteproc: qcom_q6v5_mss: Add modem debug policy support
remoteproc: qcom_q6v5_mss: Validate modem blob firmware size before load
remoteproc: qcom_q6v5_mss: Validate MBA firmware size before load
rpmsg: update documentation
remoteproc: qcom_q6v5_mss: Add MBA log extraction support
remoteproc: Add coredump debugfs entry
...
Add the character device during rproc_add. This would create
a character device node at /dev/remoteproc<index>. Userspace
applications can interact with the remote processor using this
interface.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Rishabh Bhatnagar <rishabhb@codeaurora.org>
Signed-off-by: Siddharth Gupta <sidgup@codeaurora.org>
Link: https://lore.kernel.org/r/1596044401-22083-3-git-send-email-sidgup@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add the character device interface into remoteproc framework.
This interface can be used in order to boot/shutdown remote
subsystems and provides a basic ioctl based interface to implement
supplementary functionality. An ioctl call is implemented to enable
the shutdown on release feature which will allow remote processors to
be shutdown when the controlling userspace application crashes or hangs.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Rishabh Bhatnagar <rishabhb@codeaurora.org>
Signed-off-by: Siddharth Gupta <sidgup@codeaurora.org>
Link: https://lore.kernel.org/r/1596044401-22083-2-git-send-email-sidgup@codeaurora.org
[bjorn: s/int32_t/s32/ per checkpatch]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The IPA code now uses the generic remoteproc SSR notification
mechanism. This makes the original IPA notification code unused
and unnecessary, so get rid of it.
This is effectively a revert of commit d7f5f3c89c ("remoteproc:
add IPA notification to q6v5 driver").
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Alex Elder <elder@linaro.org>
Link: https://lore.kernel.org/r/20200724181142.13581-3-elder@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The Texas Instrument's K3 J721E SoCs have a newer next-generation
C71x DSP Subsystem in the MAIN voltage domain in addition to the
previous generation C66x DSP subsystems. The C71x DSP subsystem is
based on the TMS320C71x DSP CorePac module. The C71x CPU is a true
64-bit machine including 64-bit memory addressing and single-cycle
64-bit base arithmetic operations and supports vector signal processing
providing a significant lift in DSP processing power over C66x DSPs.
J721E SoCs use a C711 (a one-core 512-bit vector width CPU core) DSP
that is cache coherent with the A72 Arm cores.
Each subsystem has one or more Fixed/Floating-Point DSP CPUs, with 32 KB
of L1P Cache, 48 KB of L1D SRAM that can be configured and partitioned as
either RAM and/or Cache, and 512 KB of L2 SRAM configurable as either RAM
and/or Cache. The CorePac also includes a Matrix Multiplication Accelerator
(MMA), a Stream Engine (SE) and a C71x Memory Management Unit (CMMU), an
Interrupt Controller (INTC) and a Powerdown Management Unit (PMU) modules.
Update the existing K3 DSP remoteproc driver to add support for this C71x
DSP subsystem. The firmware loading support is provided by using the newly
added 64-bit ELF loader support, and is limited to images using only
external DDR memory at the moment. The L1D and L2 SRAMs are used as scratch
memory when using as RAMs, and cannot be used for loadable segments. The
CMMU is also not supported to begin with, and the driver is designed to
treat the MMU as if it is in bypass mode.
Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20200612225357.8251-3-s-anna@ti.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The resets for the DSP processors on K3 SoCs are managed through the
Power and Sleep Controller (PSC) module. Each DSP typically has two
resets - a global module reset for powering on the device, and a local
reset that affects only the CPU while allowing access to the other
sub-modules within the DSP processor sub-systems.
The C66x DSPs have two levels of internal RAMs that can be used to
boot from, and the firmware loading into these RAMs require the
local reset to be asserted with the device powered on/enabled using
the module reset. Enhance the K3 DSP remoteproc driver to add support
for loading into the internal RAMs. The local reset is deasserted on
SoC power-on-reset, so logic has to be added in probe in remoteproc
mode to balance the remoteproc state-machine.
Note that the local resets are a no-op on C71x cores, and the hardware
does not supporting loading into its internal RAMs.
Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20200721223617.20312-7-s-anna@ti.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The Texas Instrument's K3 J721E SoCs have two C66x DSP Subsystems in MAIN
voltage domain that are based on the TI's standard TMS320C66x DSP CorePac
module. Each subsystem has a Fixed/Floating-Point DSP CPU, with 32 KB each
of L1P & L1D SRAMs that can be configured and partitioned as either RAM
and/or Cache, and 288 KB of L2 SRAM with 256 KB of memory configurable as
either RAM and/or Cache. The CorePac also includes an Internal DMA (IDMA),
External Memory Controller (EMC), Extended Memory Controller (XMC) with a
Region Address Translator (RAT) unit for 32-bit to 48-bit address
extension/translations, an Interrupt Controller (INTC) and a Powerdown
Controller (PDC).
A new remoteproc module is added to perform the device management of
these DSP devices. The support is limited to images using only external
DDR memory at the moment, the loading support to internal memories and
any on-chip RAM memories will be added in a subsequent patch. RAT support
is also left for a future patch, and as such the reserved memory carveout
regions are all expected to be using memory regions within the first 2 GB.
Error Recovery and Power Management features are not currently supported.
The C66x remote processors do not have an MMU, and so require fixed memory
carveout regions matching the firmware image addresses. Support for this
is provided by mandating multiple memory regions to be attached to the
remoteproc device. The first memory region will be used to serve as the
DMA pool for all dynamic allocations like the vrings and vring buffers.
The remaining memory regions are mapped into the kernel at device probe
time, and are used to provide address translations for firmware image
segments without the need for any RSC_CARVEOUT entries. Any firmware
image using memory outside of the supplied reserved memory carveout
regions will be errored out.
The driver uses various TI-SCI interfaces to talk to the System Controller
(DMSC) for managing configuration, power and reset management of these
cores. IPC between the A72 cores and the DSP cores is supported through
the virtio rpmsg stack using shared memory and OMAP Mailboxes.
Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20200721223617.20312-6-s-anna@ti.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Texas Instruments' K3 generation SoCs have specific modules/register
spaces used for configuring the various aspects of a remote processor.
These include power, reset, boot vector and other configuration features
specific to each compute processor present on the SoC. These registers
are managed by the System Controller such as DMSC on K3 AM65x SoCs.
The Texas Instrument's System Control Interface (TI-SCI) Message Protocol
is used to communicate to the System Controller from various compute
processors to invoke specific services provided by the firmware running
on the System Controller.
Add a common processor control interface header file that can be used by
multiple remoteproc drivers. The helper functions within this header file
abstract the various TI SCI protocol ops for the remoteproc drivers, and
allow them to request the System Controller to be able to program and
manage various remote processors on the SoC. The remoteproc drivers are
expected to manage the life-cycle of their ti_sci_proc_dev local
structures.
Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20200721223617.20312-4-s-anna@ti.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add a new helper function rproc_of_parse_firmware() to the remoteproc
core that can be used by various remoteproc drivers to look up the
the "firmware-name" property from a rproc device node. This property
is already being used by multiple drivers, so this helper can avoid
repeating equivalent code in remoteproc drivers.
Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20200721223617.20312-3-s-anna@ti.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Remove the redundant running state, as an equivalent is maintained in
the common q6v5 resource handling helpers.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/20200602163257.26978-2-sibis@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Sometimes the stop triggers a watchdog rather than a stop-ack. Update
the running state to false on requesting stop to skip the watchdog
instead.
Error Logs:
$ echo stop > /sys/class/remoteproc/remoteproc0/state
ipa 1e40000.ipa: received modem stopping event
remoteproc-modem: watchdog received: sys_m_smsm_mpss.c:291:APPS force stop
qcom-q6v5-mss 4080000.remoteproc-modem: port failed halt
ipa 1e40000.ipa: received modem offline event
remoteproc0: stopped remote processor 4080000.remoteproc-modem
Reviewed-by: Evan Green <evgreen@chromium.org>
Fixes: 3b415c8fb2 ("remoteproc: q6v5: Extract common resource handling")
Cc: stable@vger.kernel.org
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/20200602163257.26978-1-sibis@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add modem debug policy support which will enable coredumps and live
debug support when the msadp firmware is present on secure devices.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/20200722201047.12975-4-sibis@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The following mem abort is observed when one of the modem blob firmware
size exceeds the allocated mpss region. Fix this by restricting the copy
size to segment size using request_firmware_into_buf before load.
Err Logs:
Unable to handle kernel paging request at virtual address
Mem abort info:
...
Call trace:
__memcpy+0x110/0x180
rproc_start+0xd0/0x190
rproc_boot+0x404/0x550
state_store+0x54/0xf8
dev_attr_store+0x44/0x60
sysfs_kf_write+0x58/0x80
kernfs_fop_write+0x140/0x230
vfs_write+0xc4/0x208
ksys_write+0x74/0xf8
...
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Fixes: 051fb70fd4 ("remoteproc: qcom: Driver for the self-authenticating Hexagon v5")
Cc: stable@vger.kernel.org
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/20200722201047.12975-3-sibis@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The following mem abort is observed when the mba firmware size exceeds
the allocated mba region. MBA firmware size is restricted to a maximum
size of 1M and remaining memory region is used by modem debug policy
firmware when available. Hence verify whether the MBA firmware size lies
within the allocated memory region and is not greater than 1M before
loading.
Err Logs:
Unable to handle kernel paging request at virtual address
Mem abort info:
...
Call trace:
__memcpy+0x110/0x180
rproc_start+0x40/0x218
rproc_boot+0x5b4/0x608
state_store+0x54/0xf8
dev_attr_store+0x44/0x60
sysfs_kf_write+0x58/0x80
kernfs_fop_write+0x140/0x230
vfs_write+0xc4/0x208
ksys_write+0x74/0xf8
__arm64_sys_write+0x24/0x30
...
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Fixes: 051fb70fd4 ("remoteproc: qcom: Driver for the self-authenticating Hexagon v5")
Cc: stable@vger.kernel.org
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/20200722201047.12975-2-sibis@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
On SC7180 the MBA firmware stores the bootup text logs in a 4K segment
at the beginning of the MBA region. Add support to extract the logs
which will be useful to debug mba boot/authentication issues.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/20200721112935.25716-3-sibis@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add coredump debugfs entry to configure the type of dump that will
be collected during recovery. User can select between default or
inline coredump functionality. Also coredump collection can be
disabled through this interface.
This functionality can be configured differently for different
remote processors.
Signed-off-by: Rishabh Bhatnagar <rishabhb@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Tested-by: Sibi Sankar <sibis@codeaurora.org>
Reviewed-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/1594938035-7327-6-git-send-email-rishabhb@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The current coredump implementation uses vmalloc area to copy
all the segments. But this might put strain on low memory targets
as the firmware size sometimes is in tens of MBs. The situation
becomes worse if there are multiple remote processors undergoing
recovery at the same time. This patch adds inline coredump
functionality that avoids extra memory usage. This requires
recovery to be halted until data is read by userspace and free
function is called.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Sibi Sankar <sibis@codeaurora.org>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Rishabh Bhatnagar <rishabhb@codeaurora.org>
Tested-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/1594938035-7327-5-git-send-email-rishabhb@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Change the segment dump API signature to include size and offset
arguments. Refactor the qcom_q6v5_mss driver to use these
arguments while copying the segment. Doing this lays the ground
work for "inline" coredump functionality being added in the next
patch.
Tested-by: Sibi Sankar <sibis@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Sibi Sankar <sibis@codeaurora.org>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Rishabh Bhatnagar <rishabhb@codeaurora.org>
Link: https://lore.kernel.org/r/1594938035-7327-4-git-send-email-rishabhb@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
In order to land inline coredump support for mss, the dump_segment
function would need to support granularities less than the segment
size. This is achieved by replacing mask based tracking with size.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Signed-off-by: Rishabh Bhatnagar <rishabhb@codeaurora.org>
Link: https://lore.kernel.org/r/1594938035-7327-3-git-send-email-rishabhb@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Move all coredump functionality to an individual file. This is
being done so that the current functionality can be extended
in future patchsets.
Signed-off-by: Rishabh Bhatnagar <rishabhb@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Sibi Sankar <sibis@codeaurora.org>
Tested-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/1594938035-7327-2-git-send-email-rishabhb@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Split function stm32_rproc_parse_fw() in two parts, the first one
to parse the memory regions and the second one to load the
resource table. That way parsing of the memory regions can be
done without having do deal with the resource table when attaching
to a remote processor.
Mainly based on the work published by Arnaud Pouliquen [1].
[1]. https://patchwork.kernel.org/project/linux-remoteproc/list/?series=239877
Acked-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20200714200445.1427257-9-mathieu.poirier@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Make function rproc_resource_cleanup() public so that it can be
used by platform drivers when allocating resources to be used by
a detached remote processor.
Acked-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20200714200445.1427257-8-mathieu.poirier@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Introduce the required mechanic to set the state of the M4 in order
to properly deal with scenarios where the co-processor has been
started by another entity.
Mainly based on the work published by Arnaud Pouliquen [1].
[1]. https://patchwork.kernel.org/project/linux-remoteproc/list/?series=239877
Acked-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20200714200445.1427257-7-mathieu.poirier@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Get from the DT the syncon to probe the state of the remote processor
and the location of the resource table.
Mainly based on the work published by Arnaud Pouliquen [1].
[1]. https://patchwork.kernel.org/project/linux-remoteproc/list/?series=239877
Acked-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Loic Pallardy <loic.pallardy@st.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20200714200445.1427257-6-mathieu.poirier@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Other than one has to be done after the other, there is no correlation
between memory translation and DT parsing. As such move function
stm32_rproc_of_memory_translations() to stm32_rproc_probe() so that
stm32_rproc_parse_dt() can be extended to look for attach bindings
in a clean way.
Acked-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Loic Pallardy <loic.pallardy@st.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20200714200445.1427257-5-mathieu.poirier@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Remove the remote processor from the process of parsing the device tree
since (1) there is no correlation between them and (2) to use the
information that was gathered to make a decision on whether to
synchronise with the M4 or not.
Acked-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20200714200445.1427257-4-mathieu.poirier@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Request IRQ with platform device rather than remote proc in order to
call stm32_rproc_parse_dt() before rproc_alloc(). That way we can
know whether we need to synchronise with the MCU or not.
Acked-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Loic Pallardy <loic.pallardy@st.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20200714200445.1427257-3-mathieu.poirier@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Remove the remote processor from the process of parsing the memory
ranges since there is no correlation between them.
Acked-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Loic Pallardy <loic.pallardy@st.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20200714200445.1427257-2-mathieu.poirier@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This patch prevents the firmware image name from being displayed when
the remoteproc core is attaching to a remote processor. This is needed
needed since there is no guarantee about the nature of the firmware
image that is loaded by the external entity.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Link: https://lore.kernel.org/r/20200714195035.1426873-10-mathieu.poirier@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
When function rproc_free_vring() clears the virtio device section
it does so on the cached resource table rather than the one
installed in the remote processor memory. When a remote processor
has been booted by another entity there is no need to use a cached
table and as such, no need to clear the virtio device section in
it.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Link: https://lore.kernel.org/r/20200714195035.1426873-9-mathieu.poirier@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Refactor function rproc_trigger_auto_boot() to properly deal
with scenarios where the remoteproc core needs to attach with a
remote processor that has already been booted by an external
entity.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Link: https://lore.kernel.org/r/20200714195035.1426873-8-mathieu.poirier@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Refactor function rproc_boot() to properly deal with scenarios
where the remoteproc core needs to attach with a remote
processor that has already been booted by an external entity.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Link: https://lore.kernel.org/r/20200714195035.1426873-7-mathieu.poirier@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add a new function to assert the general health of the remote
processor before handing it to the remoteproc core.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Tested-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Link: https://lore.kernel.org/r/20200714195035.1426873-6-mathieu.poirier@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Introduce function rproc_actuate() that provides the same
functionatlity as rproc_fw_boot(), but without the steps that
involve interaction with the firmware image. That way we can
deal with scenarios where the remoteproc core is attaching
to a remote processor that has already been started by another
entity.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Tested-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Link: https://lore.kernel.org/r/20200714195035.1426873-5-mathieu.poirier@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Introducing function rproc_attach() to enact the same actions as
rproc_start(), but without the steps related to the handling of
a firmware image. That way we can properly deal with scenarios
where the remoteproc core needs to attach with a remote processsor
that has been booted by another entity.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Link: https://lore.kernel.org/r/20200714195035.1426873-4-mathieu.poirier@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add an new attach() operation in order to properly deal with
scenarios where the remoteproc core needs to attach to a
remote processor that has been booted by another entity.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Link: https://lore.kernel.org/r/20200714195035.1426873-3-mathieu.poirier@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add a new RPROC_DETACHED state to take into account scenarios
where the remoteproc core needs to attach to a remote processor
that is booted by another entity.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Link: https://lore.kernel.org/r/20200714195035.1426873-2-mathieu.poirier@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
On secure devices there exists a race condition which could lock the MSS
CONFIG AHB bus thus preventing access to BOOT_STATUS register during SSR.
Switch to polling the MSS_STATUS register with an additional 10 us delay
to reliably track boot completion.
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/20200716120514.21588-1-sibis@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
On platforms with 32-bit phys_addr_t the shift to get the upper word of
the base address of the memory region is invalid. Cast the base to 64
bit to resolv this.
Fixes: 549b67da66 ("remoteproc: qcom: Introduce helper to store pil info in IMEM")
Tested-by: Nathan Chancellor <natechancellor@gmail.com> # build
Reported-by: Lee Jones <lee.jones@linaro.org>
Reported-by: Nathan Chancellor <natechancellor@gmail.com>
Link: https://lore.kernel.org/r/20200716054817.157608-1-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Looks as though 'name' has now been moved into 'struct sysmod_event'
which is passed in instead. However, the parameter descriptions were
not updated at the same time. Let's do that now.
Fixes the following W=1 kernel build warning(s):
drivers/remoteproc/qcom_sysmon.c:78: warning: Function parameter or member 'event' not described in 'sysmon_send_event'
drivers/remoteproc/qcom_sysmon.c:78: warning: Excess function parameter 'name' description in 'sysmon_send_event'
drivers/remoteproc/qcom_sysmon.c:350: warning: Function parameter or member 'event' not described in 'ssctl_send_event'
drivers/remoteproc/qcom_sysmon.c:350: warning: Excess function parameter 'name' description in 'ssctl_send_event'
Cc: Andy Gross <agross@kernel.org>
Cc: linux-arm-msm@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20200715123551.4011154-2-lee.jones@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Fixes the following W=1 kernel build warning(s):
drivers/remoteproc/remoteproc_core.c: In function ‘rproc_find_carveout_by_name’:
drivers/remoteproc/remoteproc_core.c:257:2: warning: function ‘rproc_find_carveout_by_name’ might be a candidate for ‘gnu_printf’ format attribute [-Wsuggest-attribute=format]
257 | vsnprintf(_name, sizeof(_name), name, args);
| ^~~~~~~~~
drivers/remoteproc/remoteproc_core.c: In function ‘rproc_mem_entry_init’:
drivers/remoteproc/remoteproc_core.c:993:2: warning: function ‘rproc_mem_entry_init’ might be a candidate for ‘gnu_printf’ format attribute [-Wsuggest-attribute=format]
993 | vsnprintf(mem->name, sizeof(mem->name), name, args);
| ^~~~~~~~~
drivers/remoteproc/remoteproc_core.c: In function ‘rproc_of_resm_mem_entry_init’:
drivers/remoteproc/remoteproc_core.c:1029:2: warning: function ‘rproc_of_resm_mem_entry_init’ might be a candidate for ‘gnu_printf’ format attribute [-Wsuggest-attribute=format]
1029 | vsnprintf(mem->name, sizeof(mem->name), name, args);
| ^~~~~~~~~
Cc: Brian Swetland <swetland@google.com>
Cc: Mark Grosen <mgrosen@ti.com>
Cc: Guzman Lugo <fernando.lugo@ti.com>
Cc: Suman Anna <s-anna@ti.com>
Cc: Robert Tivy <rtivy@ti.com>
Cc: De Leon <x0095078@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20200715123551.4011154-1-lee.jones@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
drivers/remoteproc/qcom_common.c: In function 'qcom_ssr_get_subsys':
drivers/remoteproc/qcom_common.c:210:9: error: implicit declaration of function 'kzalloc'; did you mean 'vzalloc'?
[-Werror=implicit-function-declaration]
info = kzalloc(sizeof(*info), GFP_KERNEL);
^~~~~~~
vzalloc
kzalloc() is declared in linux/slab.h, add include to fix build issue.
Tested-by: Alex Elder <elder@linaro.org>
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Link: https://lore.kernel.org/r/20200713020003.134039-1-wangkefeng.wang@huawei.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The SSR subdevice only adds callback for the unprepare event. Add callbacks
for prepare, start and prepare events. The client driver for a particular
remoteproc might be interested in knowing the status of the remoteproc
while undergoing SSR, not just when the remoteproc has finished shutting
down.
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Siddharth Gupta <sidgup@codeaurora.org>
Signed-off-by: Rishabh Bhatnagar <rishabhb@codeaurora.org>
Link: https://lore.kernel.org/r/1592965408-16908-3-git-send-email-rishabhb@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Currently there is a single notification chain which is called whenever any
remoteproc shuts down. This leads to all the listeners being notified, and
is not an optimal design as kernel drivers might only be interested in
listening to notifications from a particular remoteproc. Create a global
list of remoteproc notification info data structures. This will hold the
name and notifier_list information for a particular remoteproc. The API
to register for notifications will use name argument to retrieve the
notification info data structure and the notifier block will be added to
that data structure's notification chain. Also move from blocking notifier
to srcu notifer based implementation to support dynamic notifier head
creation.
Reviewed-by: Alex Elder <elder@linaro.org>
Co-developed-by: Siddharth Gupta <sidgup@codeaurora.org>
Signed-off-by: Siddharth Gupta <sidgup@codeaurora.org>
Signed-off-by: Rishabh Bhatnagar <rishabhb@codeaurora.org>
Link: https://lore.kernel.org/r/1592965408-16908-2-git-send-email-rishabhb@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Update the PIL relocation information in IMEM with information about
where the firmware for various remoteprocs are loaded.
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20200622191942.255460-4-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
A region in IMEM is used to communicate load addresses of remoteproc to
post mortem debug tools. Implement a helper function that can be used to
store this information in order to enable these tools to process
collected ramdumps.
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20200622191942.255460-3-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This reverts commit a99a37f6cd.
Removing PM runtime operations from the remoteproc core in order to:
1) Keep all power management operations in platform drivers. That way we
do not loose flexibility in an area that is very HW specific.
2) Avoid making the support for remote processor managed by external
entities more complex that it already is.
3) Fix regression introduced for the Omap remoteproc driver.
Acked-by: Suman Anna <s-anna@ti.com>
Tested-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20200630163118.3830422-3-mathieu.poirier@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The header file linux/uio.h includes crypto/hash.h which pulls in
most of the Crypto API. Since linux/uio.h is used throughout the
kernel this means that every tiny bit of change to the Crypto API
causes the entire kernel to get rebuilt.
This patch fixes this by moving it into lib/iov_iter.c instead
where it is actually used.
This patch also fixes the ifdef to use CRYPTO_HASH instead of just
CRYPTO which does not guarantee the existence of ahash.
Unfortunately a number of drivers were relying on linux/uio.h to
provide access to linux/slab.h. This patch adds inclusions of
linux/slab.h as detected by build failures.
Also skbuff.h was relying on this to provide a declaration for
ahash_request. This patch adds a forward declaration instead.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
This introduces device managed versions of functions used to register
remoteproc devices, add support for remoteproc driver specific resource
control, enables remoteproc drivers to specify ELF class and machine for
coredumps. It integrates pm_runtime in the core for keeping resources
active while the remote is booted and holds a wake source while
recoverying a remote processor after a firmware crash.
It refactors the remoteproc device's allocation path to simplify the
logic, fix a few cleanup bugs and to not clone const strings onto the
heap. Debugfs code is simplifies using the DEFINE_SHOW_ATTRIBUTE and a
zero-length array is replaced with flexible-array.
A new remoteproc driver for the JZ47xx VPU is introduced, the Qualcomm
SM8250 gains support for audio, compute and sensor remoteprocs and the
Qualcomm SC7180 modem support is cleaned up and improved.
The Qualcomm glink subsystem-restart driver is merged into the main
glink driver, the Qualcomm sysmon driver is extended to properly notify
remote processors about all other remote processors' state transitions.
-----BEGIN PGP SIGNATURE-----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=4k54
-----END PGP SIGNATURE-----
Merge tag 'rproc-v5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/andersson/remoteproc
Pull remoteproc updates from Bjorn Andersson:
"This introduces device managed versions of functions used to register
remoteproc devices, add support for remoteproc driver specific
resource control, enables remoteproc drivers to specify ELF class and
machine for coredumps. It integrates pm_runtime in the core for
keeping resources active while the remote is booted and holds a wake
source while recoverying a remote processor after a firmware crash.
It refactors the remoteproc device's allocation path to simplify the
logic, fix a few cleanup bugs and to not clone const strings onto the
heap. Debugfs code is simplifies using the DEFINE_SHOW_ATTRIBUTE and a
zero-length array is replaced with flexible-array.
A new remoteproc driver for the JZ47xx VPU is introduced, the Qualcomm
SM8250 gains support for audio, compute and sensor remoteprocs and the
Qualcomm SC7180 modem support is cleaned up and improved.
The Qualcomm glink subsystem-restart driver is merged into the main
glink driver, the Qualcomm sysmon driver is extended to properly
notify remote processors about all other remote processors' state
transitions"
* tag 'rproc-v5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/andersson/remoteproc: (43 commits)
remoteproc: Fix an error code in devm_rproc_alloc()
MAINTAINERS: Add myself as reviewer for Ingenic rproc driver
remoteproc: ingenic: Added remoteproc driver
remoteproc: Add support for runtime PM
dt-bindings: Document JZ47xx VPU auxiliary processor
remoteproc: wcss: Fix arguments passed to qcom_add_glink_subdev()
remoteproc: Fix and restore the parenting hierarchy for vdev
remoteproc: Fall back to using parent memory pool if no dedicated available
remoteproc: Replace zero-length array with flexible-array
remoteproc: wcss: add support for rpmsg communication
remoteproc: core: Prevent system suspend during remoteproc recovery
remoteproc: qcom_q6v5_mss: Remove unused q6v5_da_to_va function
remoteproc: qcom_q6v5_mss: map/unmap mpss segments before/after use
remoteproc: qcom_q6v5_mss: Drop accesses to MPSS PERPH register space
dt-bindings: remoteproc: qcom: Replace halt-nav with spare-regs
remoteproc: qcom: pas: Add SM8250 PAS remoteprocs
dt-bindings: remoteproc: qcom: pas: Add SM8250 remoteprocs
remoteproc: qcom_q6v5_mss: Extract mba/mpss from memory-region
dt-bindings: remoteproc: qcom: Use memory-region to reference memory
remoteproc: qcom: pas: Add SC7180 Modem support
...
The comments say that this function should return NULL on error and the
caller expects NULL returns as well so I have modified the code to match.
Returning an ERR_PTR(-ENOMEM) would lead to an OOps.
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Fixes: 305ac5a766 ("remoteproc: Add device-managed variants of rproc_alloc/rproc_add")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20200520120705.GH172354@mwanda
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This driver is used to boot, communicate with and load firmwares to the
MIPS co-processor found in the VPU hardware of the JZ47xx SoCs from
Ingenic.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Acked-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20200515104340.10473-4-paul@crapouillou.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Call pm_runtime_get_sync() before the firmware is loaded, and
pm_runtime_put() after the remote processor has been stopped.
Even though the remoteproc device has no PM callbacks, this allows the
parent device's PM callbacks to be properly called.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20200515104340.10473-3-paul@crapouillou.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Recently qcom_add_glink_subdev() was extended to also take the glink_ssr
identifier as an argument and I missed this while applying '8a226e2c71bb
("remoteproc: wcss: add support for rpmsg communication")'.
Fixes: 8a226e2c71 ("remoteproc: wcss: add support for rpmsg communication")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20200514185856.1598945-1-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The commit 086d08725d ("remoteproc: create vdev subdevice with specific
dma memory pool") has introduced a new vdev subdevice for each vdev
declared in the firmware resource table and made it as the parent for the
created virtio rpmsg devices instead of the previous remoteproc device.
This changed the overall parenting hierarchy for the rpmsg devices, which
were children of virtio devices, and does not allow the corresponding
rpmsg drivers to retrieve the parent rproc device through the
rproc_get_by_child() API.
Fix this by restoring the remoteproc device as the parent. The new vdev
subdevice can continue to inherit the DMA attributes from the remoteproc's
parent device (actual platform device).
Cc: stable@vger.kernel.org
Fixes: 086d08725d ("remoteproc: create vdev subdevice with specific dma memory pool")
Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Acked-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Link: https://lore.kernel.org/r/20200420160600.10467-3-s-anna@ti.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
In some cases, like with OMAP remoteproc, we are not creating dedicated
memory pool for the virtio device. Instead, we use the same memory pool
for all shared memories. The current virtio memory pool handling forces
a split between these two, as a separate device is created for it,
causing memory to be allocated from bad location if the dedicated pool
is not available. Fix this by falling back to using the parent device
memory pool if dedicated is not available.
Cc: stable@vger.kernel.org
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Acked-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Fixes: 086d08725d ("remoteproc: create vdev subdevice with specific dma memory pool")
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Link: https://lore.kernel.org/r/20200420160600.10467-2-s-anna@ti.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The system might go into suspend during recovery of any remoteproc.
This will interrupt the recovery process in between increasing the
recovery time. Make the platform device as wakeup capable and
use pm_stay_wake/pm_relax APIs to avoid system from going into
suspend during recovery.
Signed-off-by: Siddharth Gupta <sidgup@codeaurora.org>
Signed-off-by: Rishabh Bhatnagar <rishabhb@codeaurora.org>
Acked-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/1588183482-21146-1-git-send-email-rishabhb@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Remove unsed q6v5_da_to_va function as the mss driver uses a per segment
dump function.
Tested-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/20200415071619.6052-2-sibis@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The application processor accessing the mpss region when the Q6 modem is
running will lead to an XPU violation. Fix this by un-mapping the mpss
segments post copy during mpss authentication and coredumps.
Tested-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/20200415071619.6052-1-sibis@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
7C retail devices using MSA based boot will result in a fuse combination
which will prevent accesses to MSS PERPH register space where the mpss
clocks and halt-nav reside. So drop all accesses to the MPSS PERPH
register space. Issuing HALT NAV request and turning on the mss clocks
as part of SSR will no longer be required since the modem firmware will
have the necessary fixes to ensure that there are no pending NAV DMA
transactions.
Tested-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/20200415145110.20624-3-sibis@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
In the absence of mba and mpss sub-child extract the mba/mpss regions
from the memory-region property.
Tested-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/20200421143228.8981-5-sibis@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add support for booting the Modem DSP found on Qualcomm's SC7180 SoCs.
Tested-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/20200421143228.8981-3-sibis@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
sizeof() when applied to a pointer typed expression gives the
size of the pointer, not that of the pointed data.
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Fixes: 63c13d61ea ("remoteproc/mediatek: add SCP support for mt8183")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Link: https://lore.kernel.org/r/20200509084237.36293-1-weiyongjun1@huawei.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Rather than carrying a special purpose blocking notifier for glink_ssr
in remoteproc's qcom_common.c, move it into glink_ssr so allow wider
reuse of the common one.
The rpmsg glink header file is used in preparation for the next patch.
Acked-by: Chris Lew <clew@codeaurora.org>
Acked-by: Rishabh Bhatnagar <rishabhb@codeaurora.org>
Link: https://lore.kernel.org/r/20200423003736.2027371-3-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Pass ssr_name to glink subdevice in preparation for tying glink_ssr to
the glink subdevice, rather than having its own "ssr subdevice".
Acked-by: Chris Lew <clew@codeaurora.org>
Acked-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Acked-by: Rishabh Bhatnagar <rishabhb@codeaurora.org>
Link: https://lore.kernel.org/r/20200423003736.2027371-2-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This fixes a regression in the probe error path of the Qualcomm modem
remoteproc driver and a mix up of phy_addr_t and dma_addr_t in the
Mediatek SCP control driver.
-----BEGIN PGP SIGNATURE-----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=WDtr
-----END PGP SIGNATURE-----
Merge tag 'rproc-v5.7-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/andersson/remoteproc
Pull remoteproc fixes from Bjorn Andersson:
"This fixes a regression in the probe error path of the Qualcomm modem
remoteproc driver and a mix up of phy_addr_t and dma_addr_t in the
Mediatek SCP control driver"
* tag 'rproc-v5.7-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/andersson/remoteproc:
remoteproc: mtk_scp: use dma_addr_t for DMA API
remoteproc: qcom_q6v5_mss: fix q6v5_probe() error paths
remoteproc: qcom_q6v5_mss: fix a bug in q6v5_probe()
Message logged by 'dev_xxx()' or 'pr_xxx()' should end with a '\n'.
Fixes: 791c13b709 ("remoteproc: Fix NULL pointer dereference in rproc_virtio_notify")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/20200411160750.32573-1-christophe.jaillet@wanadoo.fr
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
On some SoC architecture, it is needed to enable HW like
clock, bus, regulator, memory region... before loading
co-processor firmware.
This patch introduces prepare and unprepare ops to execute
platform specific function before firmware loading and after
stop execution.
Signed-off-by: Loic Pallardy <loic.pallardy@st.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20200417002036.24359-2-s-anna@ti.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Since checks are present in the remoteproc elf loader before calling
da_to_va, loading a elf64 will work on 32bits flavors of kernel.
Indeed, if a segment size is larger than what size_t can hold, the
loader will return an error so the functionality is equivalent to
what exists today.
Acked-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Clement Leger <cleger@kalray.eu>
Link: https://lore.kernel.org/r/20200422093017.10985-1-cleger@kalray.eu
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add API functions devm_rproc_alloc() and devm_rproc_add(), which behave
like rproc_alloc() and rproc_add() respectively, but register their
respective cleanup function to be called on driver detach.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20200417170040.174319-2-paul@crapouillou.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The current name field used in the remoteproc structure is simply
a pointer to a name field supplied during the rproc_alloc() call.
The pointer passed in by remoteproc drivers during registration is
typically a dev_name pointer, but it is possible that the pointer
will no longer remain valid if the devices themselves were created
at runtime like in the case of of_platform_populate(), and were
deleted upon any failures within the respective remoteproc driver
probe function.
So, allocate and maintain a local copy for this name field to
keep it agnostic of the logic used in the remoteproc drivers.
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Suman Anna <s-anna@ti.com>
Link: https://lore.kernel.org/r/20200417002036.24359-3-s-anna@ti.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Get rid of tedious error management by moving firmware and operation
allocation after calling device_initialize(). That way we take advantage
of the automatic call to rproc_type_release() to cleanup after ourselves
when put_device() is called.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Alex Elder <elder@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Suman Anna <s-anna@ti.com>
Link: https://lore.kernel.org/r/20200420231601.16781-5-mathieu.poirier@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Make the rproc_ops allocation a function on its own in an effort
to clean up function rproc_alloc().
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Alex Elder <elder@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20200420231601.16781-4-mathieu.poirier@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Improve the readability of function rproc_alloc_firmware() by using
a non-negated condition and moving the comment out of the conditional
block
Suggested-by: Alex Elder <elder@linaro.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Alex Elder <elder@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20200420231601.16781-3-mathieu.poirier@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
For cases where @firmware is declared "const char *", use function
kstrdup_const() to avoid needlessly creating another copy on the
heap.
Suggested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Alex Elder <elder@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20200420231601.16781-2-mathieu.poirier@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Clients/services running on a remoteproc that booted up might need to be
aware of the state of already running remoteprocs. When a remoteproc boots
up (fresh or after recovery) it is not aware of the remoteprocs that booted
before it, i.e., the system state is incomplete. So to keep track of it we
send sysmon on behalf of all 'ONLINE' remoteprocs.
Acked-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Siddharth Gupta <sidgup@codeaurora.org>
Link: https://lore.kernel.org/r/1586389003-26675-4-git-send-email-sidgup@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add notification for other stages of remoteproc boot and shutdown. This
includes adding callback functions for the prepare and unprepare events,
and fleshing out the callback function for start.
Acked-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Siddharth Gupta <sidgup@codeaurora.org>
Link: https://lore.kernel.org/r/1586389003-26675-3-git-send-email-sidgup@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Current implementation of the sysmon driver does not support adding
notifications for other remoteproc events - prepare, start, unprepare.
Clients on the remoteproc side might be interested in knowing when a
remoteproc boots up. This change adds the ability to send the notification
type along with the name. For example, audio DSP is interested in knowing
when modem has crashed so that it can perform cleanup and wait for modem to
boot up before it starts processing data again.
Acked-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Siddharth Gupta <sidgup@codeaurora.org>
Link: https://lore.kernel.org/r/1586389003-26675-2-git-send-email-sidgup@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Modify drivers which are using remoteproc coredump functionality to use
rproc_coredump_set_elf_info in order to create correct elf coredump
format.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Clement Leger <cleger@kalray.eu>
Link: https://lore.kernel.org/r/20200410102433.2672-3-cleger@kalray.eu
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
In an effort to cleanup firmware name allocation, replace the
cumbersome mechanic used to allocate a default firmware name with
function kasprintf().
Reviewed-by: Alex Elder <elder@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Suggested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20200415204858.2448-4-mathieu.poirier@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Make the firmware name allocation a function on its own in an
effort to cleanup function rproc_alloc().
Reviewed-by: Alex Elder <elder@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20200415204858.2448-3-mathieu.poirier@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
If ida_simple_get() returns an error when called in rproc_alloc(),
put_device() is called to clean things up. By this time the rproc
device type has been assigned, with rproc_type_release() as the
release function.
The first thing rproc_type_release() does is call:
idr_destroy(&rproc->notifyids);
But at the time the ida_simple_get() call is made, the notifyids
field in the remoteproc structure has not been initialized.
I'm not actually sure this case causes an observable problem, but
it's incorrect. Fix this by initializing the notifyids field before
calling ida_simple_get() in rproc_alloc().
Fixes: b5ab5e24e9 ("remoteproc: maintain a generic child device for each rproc")
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20200415204858.2448-2-mathieu.poirier@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Suman Anna
Christoph Hellwig
Alexandre Courbot
Pi-Hsun Shih
Sibi Sankar
Colin Ian King
Jim Quinlan
Mathieu Poirier
Gustavo A. R. Silva
Linus Torvalds
Siddharth Gupta
Alex Elder
Rishabh Bhatnagar
Bjorn Andersson
Lee Jones
Kefeng Wang
Herbert Xu
Dan Carpenter
Paul Cercueil
Tero Kristo
Sivaprakash Murugesan
Wei Yongjun
Christophe JAILLET
Loic Pallardy
Clement Leger
Michael S. Tsirkin