If SPI is used for periodic polling any sensor, significant delays
sometimes appear. Switching on module clocks during resume lead to delays.
Enabling autosuspend mode causes the controller to not suspend between
SPI transfers and the delays disappear.
The commit also remove unnecessary call to pm_runtime_idle() used
to explicit put device to suspended state. Without pm_runtime_idle() PM
core will put device in the suspended state just after probe() returns.
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/r/20201019150343.2520-1-akochetkov@lintech.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
DMA-based transfer will be enabled if data length is larger than FIFO size
(64 bytes for A64). This greatly reduce number of interrupts for
transferring data.
For smaller data size PIO mode will be used. In PIO mode whole buffer will
be loaded into FIFO.
If driver failed to request DMA channels then it fallback for PIO mode.
Tested on SOPINE (https://www.pine64.org/sopine/)
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/r/20201022075221.23332-1-akochetkov@lintech.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
In sun6i_spi_transfer_one() the RX FIFO Ready (SUN6I_INT_CTL_RF_RDY) is
unconditionally enabled.
A RX interrupt is only needed, if more data than fits into the FIFO is going to
be received during this transfer. As the RX-FIFO is drained during transfer
complete interrupt, enable the RX FIFO Ready interrupt only if the data doesn't
fit into the FIFO.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/r/20200706143443.9855-11-mkl@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
In sun6i_spi_transfer_one() the Interrupt Control Register is written three
times. This patch collates the three writes into one.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/r/20200706143443.9855-10-mkl@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The function sun6i_spi_fill_fifo() is called with a length argument of
"sspi->fifo_depth" and "SUN6I_FIFO_DEPTH".
The driver reads the number of free bytes in the FIFO from the hardware and
uses the length argument to limit this value. This is not needed as the number
of free bytes in the FIFO is always less or equal the depth of the FIFO.
This patch removes the length argument and check.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/r/20200706143443.9855-9-mkl@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The function sun6i_spi_drain_fifo() is called with a length argument of
"sspi->fifo_depth" and "SUN6I_FIFO_DEPTH".
The driver reads the number of available bytes to read from the FIFO from the
hardware and uses the length argument to limit this value. This is not needed
as the FIFO can contain only the fifo depth number of bytes.
This patch removes the length argument and check.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/r/20200706143443.9855-8-mkl@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch introduces the function sun6i_spi_get_rx_fifo_count(), similar to
the existing sun6i_spi_get_tx_fifo_count(), to make the sun6i_spi_drain_fifo()
function a bit easier to read.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/r/20200706143443.9855-7-mkl@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch converts the manual shift+mask in sun6i_spi_get_tx_fifo_count() to
make use of FIELD_GET()
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/r/20200706143443.9855-6-mkl@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
In sun6i_spi_transfer_one() the driver ensures that the length of the transfer
is smaller or equal to SUN6I_MAX_XFER_SIZE. This means the masking of the
length to SUN6I_MAX_XFER_SIZE can be skipped when writing the transfer length
into the registers.
This patch removes the useless masking of the transfer length to
SUN6I_MAX_XFER_SIZE.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/r/20200706143443.9855-5-mkl@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch removes an useless goto at the end of
sun6i_spi_transfer_one().
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/r/20200706143443.9855-4-mkl@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch implementes the reporting of the effectivly used speed_hz for the
transfer by setting tfr->effective_speed_hz.
See the following patch, which adds this feature to the SPI core for more
information:
5d7e2b5ed5 spi: core: allow reporting the effectivly used speed_hz for a transfer
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/r/20200706143443.9855-3-mkl@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
A SPI transfer defines the _maximum_ speed of the SPI transfer. However the
driver doesn't take into account that the clock divider is always rounded down
(due to integer arithmetics). This results in a too high clock rate for the SPI
transfer.
E.g.: with a mclk_rate of 24 MHz and a SPI transfer speed of 10 MHz, the
original code calculates a reg of "0", which results in a effective divider of
"2" and a 12 MHz clock for the SPI transfer.
This patch fixes the issue by using DIV_ROUND_UP() instead of a plain
integer division.
While there simplify the divider calculation for the CDR1 case, use
order_base_2() instead of two ilog2() calculations.
Fixes: 3558fe900e ("spi: sunxi: Add Allwinner A31 SPI controller driver")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/r/20200706143443.9855-2-mkl@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190904135918.25352-31-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.
// <smpl>
@@
expression ret;
struct platform_device *E;
@@
ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);
if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>
While we're here, remove braces on if statements that only have one
statement (manually).
Cc: Mark Brown <broonie@kernel.org>
Cc: linux-spi@vger.kernel.org
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20190730181557.90391-42-swboyd@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
sun6i_spi_probe() uses sun6i_spi_runtime_resume() to prepare/enable
clocks, so sun6i_spi_remove() should use sun6i_spi_runtime_suspend() to
disable/unprepare them if we're not suspended.
Replacing pm_runtime_disable() by pm_runtime_force_suspend() will ensure
that sun6i_spi_runtime_suspend() is called if needed.
Found by Linux Driver Verification project (linuxtesting.org).
Fixes: 3558fe900e (spi: sunxi: Add Allwinner A31 SPI controller driver)
Signed-off-by: Tobias Jordan <Tobias.Jordan@elektrobit.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit a53e35db70 ("reset: Ensure drivers are explicit when requesting
reset lines") started to transition the reset control request API calls
to explicitly state whether the driver needs exclusive or shared reset
control behavior. Convert all drivers requesting exclusive resets to the
explicit API call so the temporary transition helpers can be removed.
No functional changes.
Cc: Mark Brown <broonie@kernel.org>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: linux-spi@vger.kernel.org
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The spi-sun6i driver have already got the ability to do large transfers.
However, the max transfer size reported is still fifo depth - 1.
Update the max transfer size reported to the max value possible.
Reported-by: Martin Ayotte <martinayotte@gmail.com>
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Mark Brown <broonie@kernel.org>
The spi-sun6i driver have the same problem that spi-sun4i used to have
-- SPI transfers are limited to one FIFO depth.
This commit fixes this problem in the same way it's fixed in spi-sun4i.
See commit 196737912d ("spi: sun4i: Allow transfers larger than FIFO size")
for more information.
The sun6i SPI controllers features changeable interrupt trigger level, but I
set it to 3/4 of fifo depth, as same as the the sun4i SPI controllers.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
H3 has two SPI controllers. The size of the buffer is 64 * 8.
(8 bit transfer by 64 entry FIFO)
A31 has four controllers. The size of the buffer is 128 * 8.
(8 bit transfer by 128 entry FIFO)
Register maps are sharable, so sun6i SPI driver is reusable with
device configuration.
Use the variable, 'fifo_depth' instead of fixed value to support both SPI
controllers.
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The speed limits are unset in the sun4i and sun6i SPI drivers.
The maximum speed of SPI master is used when maximum speed of SPI slave
is not specified. Also the __spi_validate function should check that
transfer speeds do not exceed the master limits.
The user manual for A10 and A31 specifies maximum
speed of the SPI clock as 100MHz and minimum as 3kHz.
Setting the SPI clock to out-of-spec values can lock up the SoC.
Signed-off-by: Michal Suchanek <hramrach@gmail.com>
--
v2:
new patch
v3:
fix constant style
Signed-off-by: Mark Brown <broonie@kernel.org>
The trasfer timeout is fixed at 1000 ms. Reading a 4Mbyte flash over
1MHz SPI bus takes way longer than that. Calculate the timeout from the
actual time the transfer is supposed to take and multiply by 2 for good
measure.
Signed-off-by: Michal Suchanek <hramrach@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
The sun4i spi hardware can trasfer at most 63 bytes of data without DMA
support so report the limitation. Same for sun6i.
Signed-off-by: Michal Suchanek <hramrach@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Allow transfers to set the transmission speed rather than using the
device max_speed_hz value. The SPI core makes sure that the speed_hz
value is always set on the transfer.
Signed-off-by: Marcus Weseloh <mweseloh42@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This controller only supports 8 bits word length.
Set bits_per_word_mask so spi core will reject transfers that attempt to use
an unsupported bits_per_word value.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Current code in sun6i_spi_set_cs() actually clears CPHA and CPOL bits which is
obvious wrong. The define for SUN6I_TFR_CTL_CS_MASK is wrong. Fix it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The Allwinner A31 has a new SPI controller IP compared to the older Allwinner
SoCs.
It supports DMA, but the driver only does PIO for now, and DMA will be
supported eventually.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Alexander Kochetkov
Marc Kleine-Budde
Alistair Francis
YueHaibing
Stephen Boyd
Thomas Gleixner
Tobias Jordan
Philipp Zabel
Icenowy Zheng
Milo Kim
Mark Brown
Michal Suchanek
Marcus Weseloh
Wolfram Sang
Axel Lin
Maxime Ripard