The optimal change would be to move the AC97 register definitions into
the AC97 driver, unfortunately, the registers are shared between several
files. Move them into a dedicated regs-ac97.h first.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
[stripped sound/isa/* changes, replaced with the next patch -- tiwai]
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The control had an extra space at the end of the name.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix missing unsigned for irqsave flags in psc i2s driver
Make attribute visiblity static
Collect all sysfs errors before checking status
[Word wrapped DEVICE_ATTR() lines for 80 columns -- broonie]
Signed-off-by: Jon Smirl <jonsmirl@gmail.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When ASoC was converted to support full int width masks SOC_SINGLE_VALUE()
omitted the assignment of rshift, causing the control operatins to report
some mono controls as stereo. This happened to work some of the time due
to a confusion between shift and min in snd_soc_info_volsw().
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
- Setting the TFS pin selector for SPORT 0 based on whether the selected
port id F or G. If the port is F then no conflict should exist for the
TFS. When Port G is selected and EMAC then there is a conflict between
the PHY interrupt line and TFS. Current settings prevent the conflict
by ignoring the TFS pin when Port G is selected. This allows both
ssm2602 using Port G and EMAC concurrently.
- some code cleanup
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
- Codec doesn't support to configure bit clock and frame sync polarities
- Codec doesn't support DSP_A format but DSP_B with inverted bit clock
polarity
- Match also other formats with their signal polarities
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix "ASoC: OMAP: Fix DSP DAI format in McBSP DAI driver" was not correct
due misunderstanding of DSP_A format and similar error in TLV320AIC33
codec which was used to test the original fix.
This patch corrects now DSP_A format in OMAP McBSP DAI driver and is
verified with TLV320AIC23 codec that's implementing DSP_A correctly.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Cc: Arun KS <arunks@mistralsolutions.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix word clock length which must equal to one bit clock cycle in DSP mode.
Surprisingly McBSP is able synchronize into wrong length when it's
slave but e.g. TLV320AIC33 codec in slave configuration is outputting
some amount of noise if word clock length is longer than one bit clock
cycle.
Fix also bit clock and frame sync polarities in DSP mode since they are
opposite from I2S.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Cc: Arun KS <arunks@mistralsolutions.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
debugfs_create_dir() returns NULL if an error occurs, returns -ENODEV
when debugfs is not enabled in the kernel.
Signed-off-by: Zhao Lei <zhaolei@cn.fujitsu.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Make the visibility of the tristate conditional on having the OpenFirmware
helper code enabed so that users who can't use it don't see the visible
option. Kconfig ignores dependencies for select so other users are
unaffected.
Thanks to Takashi for the suggestion.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6: (33 commits)
ALSA: ASoC codec: remove unused #include <version.h>
ALSA: ASoC: update email address for Liam Girdwood
ALSA: hda: corrected invalid mixer values
ALSA: hda: add mixers for analog mixer on 92hd75xx codecs
ALSA: ASoC: Add destination and source port for DMA on OMAP1
ALSA: ASoC: Drop device registration from GTA01 lm4857 driver
ALSA: ASoC: Fix build of GTA01 audio driver
ALSA: ASoC: Add widgets before setting endpoints on GTA01
ALSA: ASoC: Fix inverted input PGA mute bits in WM8903
ALSA: ASoC: OMAP: Set DMA stream name at runtime in McBSP DAI driver
ALSA: ASoC: OMAP: Add support for OMAP2430 and OMAP34xx in McBSP DAI driver
ALSA: ASoC: OMAP: Add multilink support to McBSP DAI driver
ALSA: ASoC: Make TLV320AIC26 user-visible
ALSA: ASoC - clean up Kconfig for TLV320AIC2
ALSA: ASoC: Make WM8510 microphone input a DAPM mixer
ALSA: ASoC: Implement WM8510 bias level control
ALSA: ASoC: Remove unused AUDIO_NAME define from codec drivers
ALSA: ASoC: tlv320aic3x: Use uniform tlv320aic naming
ALSA: ASoC: Add WM8510 SPI support
ALSA: ASoC: Add WM8753 SPI support
...
Fixes this warning:
sound/soc/codecs/tlv320aic23.c: In function 'tlv320aic23_write':
sound/soc/codecs/tlv320aic23.c:104: warning: passing argument 2 of
'codec->hw_write' makes pointer from integer without a cast
Replaces i2c smbus write function with standard i2c write function
Signed-off-by: Arun KS <arunks@mistralsolutions.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The files below do not use LINUX_VERSION_CODE nor KERNEL_VERSION.
sound/soc/codecs/ad1980.c
sound/soc/codecs/wm8580.c
sound/soc/codecs/wm8900.c
This patch removes the said #include <version.h>.
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Update the contact information for Liam Girdwood in ASoC core and
drivers as my old email address is no longer valid.
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Adds destination and source port for dma in platform driver as
required by OMAP1
Signed-off-by: Arun KS <arunks@mistralsolutions.com>
Acked-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Device registration should be handled at the machine level and not
in the driver code itself. This patch removes the device registration
from the driver code in preparation for moving it to the machine
definition.
[Squashed down two parts to this patch for bisectability - there's also
a third part adding registration of the device to the out of tree GTA01
machine driver -- broonie]
Signed-off-by: Jonas Bonn <jonas.bonn@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix a couple of thinkos introduced during the I2C API update.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This prevents error messages at startup where the endpoints are being
set before the widgets/controls have even been added.
Signed-off-by: Jonas Bonn <jonas.bonn@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This suits better when adding support for multiple links and different
link formats.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Thanks to Arun KS <arunks@mistralsolutions.com> for fixing one typo in
original version of this patch.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The TLV320AIC26 Kconfig option is unusual in that it supports the
OpenFirmware machine driver which doesn't have a hard binding to the
codec driver but discovers the codec via the device tree. This makes it
meaningful to select the codec without a machine driver.
Ideally there would be a proxy entry so that this option was only
visible on OpenFirmware systems.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The WM8510 microphone input PGA was represented as a DAPM PGA but in
DAPM terms the functionality is that of a mixer since it takes three
switchable inputs and produces one output. Representing it as an input
was causing its controls to be misinterpreted as gain controls and
would cause some required DAPM updates to be missed.
Reported-by: Jukka Hynninen <ext-jukka.hynninen@vaisala.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The WM8510 bias level configuration blindly overwrites the power
management registers, interfering with the operation of DAPM.
Only adjust the specific bits required, implementing use of the VMID
resistor string configuration control as we go.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Implement SPI support for WM8510, cut'n'pasting from the support for
WM8731 contributed by Cliff Cai and Alan Horstmann since the wire format
is the same for both codecs.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Implement SPI support for WM8753, cut'n'pasting from the support for
WM8731 contributed by Cliff Cai and Alan Horstmann since the wire format
is the same for both codecs.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Replaces SOC_ENUM with custom SOC_SINGLE_TLV for Sidetone volume
Signed-off-by: Arun KS <arunks@mistralsolutions.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Enables DSP DAI format for McBSP in OMAP platform driver
Signed-off-by: Arun KS <arunks@mistralsolutions.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
With MMAP enabled (DMA mode) on the AD1981, there is +/- 250ms of delay between
writing data to alsa and audio starts coming out of the AD1981.
Copy more data to local buffer before starting DMA
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The ASoC machine drivers for this board were only provided as examples
for the new AT91 ASoC platform driver. Since the ETI-B1 board is
proprietary and there are other AT91 ASoC machine drivers available,
it makes sense to remove these drivers.
Signed-off-by: Frank Mandarino <fmandarino@endrelia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Eric Miao
Takashi Iwai
Kay Sievers
Mark Brown
Jon Smirl
Cliff Cai
Jarkko Nikula
Linus Torvalds
Zhaolei
Arun KS
Huang Weiyi
Liam Girdwood
Jonas Bonn
Frank Mandarino