According to Devicetree Specification v0.2 and later, Section "Generic
Names Recommendation", the node name for a pin controller device node
should be "pinctrl".
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20200821112351.5518-1-geert+renesas@glider.be
Add reset control properties to the device nodes for the Display Units
on all supported R-Car Gen2 SoCs. Note that on these SoCs, there is
only a single reset for all DU channels.
Join the clocks lines while at it, to increase uniformity.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20200218133019.22299-2-geert+renesas@glider.be
"#address-cells", "#size-cells", and "ranges" are required properties
for devices nodes compatible with "mmio-sram", leading to warnings when
running "make dtbs_check":
$ make dtbs_check DT_SCHEMA_FILES=Documentation/devicetree/bindings/sram/sram.yaml
arch/arm/boot/dts/r8a7791-koelsch.dt.yaml: sram@e63a0000: '#address-cells' is a required property
arch/arm/boot/dts/r8a7791-koelsch.dt.yaml: sram@e63a0000: '#size-cells' is a required property
arch/arm/boot/dts/r8a7791-koelsch.dt.yaml: sram@e63a0000: 'ranges' is a required property
...
Fix this by adding the missing properties to the mmio-sram device nodes
in the DTS files for all affected R-Car Gen2 and RZ/G1 SoCs.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20191213162604.1890-1-geert+renesas@glider.be
To improve human readability and enable automatic validation, the tuples
in the various properties containing interrupt specifiers should be
grouped. While "make dtbs_check" does not impose this yet for the
"interrupts" property, it does for the "interrupt-map" property, leading
to warnings like:
pci@ee090000: interrupt-map:0: [0, 0, 0, 1, 5, 0, 108, 4, 2048, 0, 0, 1, 5, 0, 108, 4, 4096, 0, 0, 2, 5, 0, 108, 4] is too long
pci@ee0d0000: interrupt-map:0: [0, 0, 0, 1, 5, 0, 113, 4, 2048, 0, 0, 1, 5, 0, 113, 4, 4096, 0, 0, 2, 5, 0, 113, 4] is too long
Fix this by grouping the tuples of the "interrupts" and "interrupt-map"
properties using angle brackets.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20191213164115.3697-4-geert+renesas@glider.be
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Add CMT0 and CMT1 to the R-Car Gen2 V2H (r8a7792) SoC.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add IIC3 node to R8A7792 SoC device tree and a DA9063 PMIC node
to V2H Blanche board device tree.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Improve the user friendliness of the DTS code base by including the
R-Car product name in each R-Car Gen2 DTSI file.
The product names are taken from:
Documentation/devicetree/bindings/arm/shmobile.txt
Signed-off-by: Magnus Damm <damm@opensource.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The DU DT bindings have been updated to drop the reg-names property.
Update the r8a7792 and r8a7794 device trees accordingly.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable support for the ARM Performance Monitor Units in the Cortex-A15
CPU cores on R-Car V2H by adding a device node for the PMU.
New Linux output:
hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counters available
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a device node for the Watchdog Timer (WDT) controller on the Renesas
R-Car V2H (r8a7792) SoC.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adjusts the definition of the SMP routine size according
to the latest changes made by commit:
"ARM: shmobile: Add watchdog support"
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Sort the subnodes of the soc node to improve maintainability.
The sort key is the address on the bus with instances of the same
IP block grouped together.
This patch should not introduce any functional change.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
* r8a7745 (RZ/G1E) SoC
- Enable SMP
Fabrizio Castro says "Add DT node for the Advanced Power Management
Unit (APMU), add the second CPU core, and use "renesas,apmu" as
"enable-method"."
* r8a7743 (RZ/G1M) SoC
- Add node for thermal sensor module with thermal-zone support
* r8a7743 (RZ/G1M) and r8a7745 (RZ/G1E) SoCs
- Add:
+ Renesas Core Match Timer (CMT) support
+ Renesas Timer Pulse Unit PWM Controller (TPU) support
+ Renesas PWM Timer Controller (PWM) support
* r8a7743 (RZ/G1M) iW-RainboW-G20D-Qseven and
r8a7745 (RZ/G1E) iW-RainboW-G22D development platforms
- Add sound support
* r8a7743 (RZ/G1M), r8a7745 (RZ/G1E) and r8a7792 (R-Car V2H) SoCs
- Allow DTBs of boards of these SoCs to build without any warnings when
compiled with W=1 using gcc-linaro-5.4.1-2017.05
+ Move nodes which have no reg property out of bus, they don't belong there
+ Also sort sub-nodes of root node to allow for easier maintenance
* r8a7790 (R-Car H2), r8a7791 (R-Car M2-W) and r8a7793 (R-Car M2-N) SoCs
- Correct critical CPU temperature
Chris Paterson says "The current R-Car Gen2 device trees define the CPU
critical temperature as 115°C.
The R-Car hardware manuals state that Tc = –40°C to +105°C. The thermal
sensor has an accuracy of ±5°C and there can be a temperature
difference of 1 or 2 degrees between Tjmax and the thermal sensor due
to the location of the latter.
This means that 95°C is a safer value to use.
This value should also apply to r8a7792 but thermal sensor support has
not been added yet."
* r8a7740 (R-Mobile A1) SoC
- Correct TPU register block size
Geert Uytterhoven says "The Timer Pulse Unit has registers that lie
outside the declared register block. Enlarge the register block size to
fix this.
This was probably based on the old platform code, which also assumed a
register block size of 0x100."
-----BEGIN PGP SIGNATURE-----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=2oL+
-----END PGP SIGNATURE-----
Merge tag 'renesas-dt2-for-v4.16' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Second Round of Renesas ARM Based SoC DT Updates for v4.16
* r8a7745 (RZ/G1E) SoC
- Enable SMP
Fabrizio Castro says "Add DT node for the Advanced Power Management
Unit (APMU), add the second CPU core, and use "renesas,apmu" as
"enable-method"."
* r8a7743 (RZ/G1M) SoC
- Add node for thermal sensor module with thermal-zone support
* r8a7743 (RZ/G1M) and r8a7745 (RZ/G1E) SoCs
- Add:
+ Renesas Core Match Timer (CMT) support
+ Renesas Timer Pulse Unit PWM Controller (TPU) support
+ Renesas PWM Timer Controller (PWM) support
* r8a7743 (RZ/G1M) iW-RainboW-G20D-Qseven and
r8a7745 (RZ/G1E) iW-RainboW-G22D development platforms
- Add sound support
* r8a7743 (RZ/G1M), r8a7745 (RZ/G1E) and r8a7792 (R-Car V2H) SoCs
- Allow DTBs of boards of these SoCs to build without any warnings when
compiled with W=1 using gcc-linaro-5.4.1-2017.05
+ Move nodes which have no reg property out of bus, they don't belong there
+ Also sort sub-nodes of root node to allow for easier maintenance
* r8a7790 (R-Car H2), r8a7791 (R-Car M2-W) and r8a7793 (R-Car M2-N) SoCs
- Correct critical CPU temperature
Chris Paterson says "The current R-Car Gen2 device trees define the CPU
critical temperature as 115°C.
The R-Car hardware manuals state that Tc = –40°C to +105°C. The thermal
sensor has an accuracy of ±5°C and there can be a temperature
difference of 1 or 2 degrees between Tjmax and the thermal sensor due
to the location of the latter.
This means that 95°C is a safer value to use.
This value should also apply to r8a7792 but thermal sensor support has
not been added yet."
* r8a7740 (R-Mobile A1) SoC
- Correct TPU register block size
Geert Uytterhoven says "The Timer Pulse Unit has registers that lie
outside the declared register block. Enlarge the register block size to
fix this.
This was probably based on the old platform code, which also assumed a
register block size of 0x100."
* tag 'renesas-dt2-for-v4.16' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (37 commits)
ARM: dts: r8a7745: Add missing clock for secondary CA7 CPU core
ARM: dts: iwg22d-sodimm: Sound DMA support via DVC on DTS
ARM: dts: iwg22d-sodimm: Sound DMA support via SRC on DTS
ARM: dts: iwg22d-sodimm: Sound DMA support via BUSIF on DTS
ARM: dts: iwg22d-sodimm: Sound DMA support on DTS
ARM: dts: iwg22d-sodimm: Sound PIO support
ARM: dts: iwg22d-sodimm: Enable SGTL5000 audio codec
ARM: dts: r8a7745: Add sound support
ARM: dts: r8a7745: Add audio DMAC support
ARM: dts: r8a7745: Add audio clocks
ARM: dts: r8a7740: Correct TPU register block size
ARM: dts: r8a7743: move timer and thermal-zones nodes out of bus
ARM: dts: r8a7743: sort root sub-nodes alphabetically
ARM: dts: iwg20d-q7-common: Sound DMA support via DVC on DTS
ARM: dts: iwg20d-q7-common: Sound DMA support via SRC on DTS
ARM: dts: iwg20d-q7-common: Sound DMA support via BUSIF on DTS
ARM: dts: iwg20d-q7-common: Sound DMA support on DTS
ARM: dts: iwg20d-q7-common: Sound PIO support
ARM: dts: iwg20d-q7-common: Enable SGTL5000 audio codec
ARM: dts: r8a7792: move timer node out of bus
...
Signed-off-by: Olof Johansson <olof@lixom.net>
* Convert to named i2c-gpio bindings
Geert Uytterhoeven says "Commits 7d29f509d2 ("dt-bindings: i2c:
i2c-gpio: Add support for named gpios") and 05c7477885 ("i2c: gpio:
Add support for named gpios in DT") introduced named i2c-gpio DT
bindings, and deprecated the more error-prone unnamed variant.
This patch series switches all Renesas boards to the new bindings, and
adds the missing GPIO_OPEN_DRAIN I/O flags, which were implicitly
assumed before..."
... Note that after this series is applied, the i2c-gpio buses are no
longer detected when booting new DTBs on old (v4.14 and older) kernels,
which should not be an issue. Booting old DTBs on new kernels is not
affected."
* Update DTS for CMT DT binding rework
Geert Uytterhoeven says "This patch series updates the CMT device nodes
in the various Renesas DTS files sh_cmt clocksource driver for the recent
DT binding rework that was merged in v4.14-rc1 and v4.15-rc1..."
* Add SMP support to r8a7794 (R-Car E2) SoC
Sergei Shtylyov says "Add the device tree node for the Advanced Power
Management Unit (APMU). Use the "enable-method" prop to point out that
the APMU should be used for the SMP support."
* Correct primary compatible value for eeprom
on r7s72100 (RZ/A1H) genmai and r8a7791 (R-Car M2-W) koelsh boards
Geert Uytterhoeven says "The Renesas part numbers of the two-wire serial
interface EEPROMs do not follow the 24Cxx pattern, but the R1EX24xxx
pattern.
Hence change the primary compatible values to the appropriate variant of
"renesas,r1ex24xxx", like is already done on Gose.""
* Move cec_clock to root node on r8a7791 (R-Car M2-W) koelsh board
r8a7791 (R-Car M2-W) koelsh board
* Use R-Car SDHI and Ether Gen1 and 2 fallback compat strings
Use recently posted R-Car SDHI and Ether Gen 1 and 2 fallback
compat strings in the DT of Renesas ARM based SoCs.
* Add IIC cores to dtsi of r8a7745 (RZ/G1E) SoC
* Rework DT architecture for r8a7745 (RZ/G1E) iW-RainboW-G22D development
platform and add serial support.
Fabrizio Castro says "... define a new DT architecture for the
iW-RainboW-G22D SODIMM Development Platform to include the configuration
with the HDMI daughter board and to define the serial interfaces."
* Add USB function support to
r8a7745 (RZ/G1E) iW-RainboW-G22D development platform
* Add PCIEC and ttySC3 support to r8a7743 (RZ/G1M) iW-RainboW-G20M-Qseven SoM
* Add VIN support to r8a7743 (RZ/G1M) and r8a7745 (RZ/G1E) SoCs
* Add CAN and HDMI support to r8a7743 (RZ/G1M) iW-RainboW-G20D-Qseven and
r8a7745 (RZ/G1E) iW-RainboW-G22D development platforms
-----BEGIN PGP SIGNATURE-----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=Yk5x
-----END PGP SIGNATURE-----
Merge tag 'renesas-dt-for-v4.16' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Pull "Renesas ARM Based SoC DT Updates for v4.16" from Simon Horman:
* Convert to named i2c-gpio bindings
Geert Uytterhoeven says "Commits 7d29f509d2 ("dt-bindings: i2c:
i2c-gpio: Add support for named gpios") and 05c7477885 ("i2c: gpio:
Add support for named gpios in DT") introduced named i2c-gpio DT
bindings, and deprecated the more error-prone unnamed variant.
This patch series switches all Renesas boards to the new bindings, and
adds the missing GPIO_OPEN_DRAIN I/O flags, which were implicitly
assumed before..."
... Note that after this series is applied, the i2c-gpio buses are no
longer detected when booting new DTBs on old (v4.14 and older) kernels,
which should not be an issue. Booting old DTBs on new kernels is not
affected."
* Update DTS for CMT DT binding rework
Geert Uytterhoeven says "This patch series updates the CMT device nodes
in the various Renesas DTS files sh_cmt clocksource driver for the recent
DT binding rework that was merged in v4.14-rc1 and v4.15-rc1..."
* Add SMP support to r8a7794 (R-Car E2) SoC
Sergei Shtylyov says "Add the device tree node for the Advanced Power
Management Unit (APMU). Use the "enable-method" prop to point out that
the APMU should be used for the SMP support."
* Correct primary compatible value for eeprom
on r7s72100 (RZ/A1H) genmai and r8a7791 (R-Car M2-W) koelsh boards
Geert Uytterhoeven says "The Renesas part numbers of the two-wire serial
interface EEPROMs do not follow the 24Cxx pattern, but the R1EX24xxx
pattern.
Hence change the primary compatible values to the appropriate variant of
"renesas,r1ex24xxx", like is already done on Gose.""
* Move cec_clock to root node on r8a7791 (R-Car M2-W) koelsh board
r8a7791 (R-Car M2-W) koelsh board
* Use R-Car SDHI and Ether Gen1 and 2 fallback compat strings
Use recently posted R-Car SDHI and Ether Gen 1 and 2 fallback
compat strings in the DT of Renesas ARM based SoCs.
* Add IIC cores to dtsi of r8a7745 (RZ/G1E) SoC
* Rework DT architecture for r8a7745 (RZ/G1E) iW-RainboW-G22D development
platform and add serial support.
Fabrizio Castro says "... define a new DT architecture for the
iW-RainboW-G22D SODIMM Development Platform to include the configuration
with the HDMI daughter board and to define the serial interfaces."
* Add USB function support to
r8a7745 (RZ/G1E) iW-RainboW-G22D development platform
* Add PCIEC and ttySC3 support to r8a7743 (RZ/G1M) iW-RainboW-G20M-Qseven SoM
* Add VIN support to r8a7743 (RZ/G1M) and r8a7745 (RZ/G1E) SoCs
* Add CAN and HDMI support to r8a7743 (RZ/G1M) iW-RainboW-G20D-Qseven and
r8a7745 (RZ/G1E) iW-RainboW-G22D development platforms
* tag 'renesas-dt-for-v4.16' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (61 commits)
ARM: dts: alt: Convert to named i2c-gpio bindings
ARM: dts: koelsch: Convert to named i2c-gpio bindings
ARM: dts: lager: Convert to named i2c-gpio bindings
ARM: dts: armadillo800eva: Convert to named i2c-gpio bindings
ARM: dts: sh73a0: Remove CMT renesas,channels-mask
ARM: dts: r8a7794: Remove CMT renesas,channels-mask
ARM: dts: r8a7793: Remove CMT renesas,channels-mask
ARM: dts: r8a7791: Remove CMT renesas,channels-mask
ARM: dts: r8a7790: Remove CMT renesas,channels-mask
ARM: dts: r8a7740: Remove CMT renesas,channels-mask
ARM: dts: r8a73a4: Remove CMT renesas,channels-mask
ARM: dts: r8a7794: Update CMT compat strings
ARM: dts: r8a7793: Update CMT compat strings
ARM: dts: r8a7791: Update CMT compat strings
ARM: dts: r8a7790: Update CMT compat strings
ARM: dts: r8a73a4: Update CMT compat string
ARM: dts: r8a7794: Add SMP support
ARM: dts: genmai: Correct primary compatible value for eeprom
ARM: dts: koelsch: Correct primary compatible value for eeprom
ARM: dts: r8a7745: add VIN dt support
...
The timer node does not have any register properties and thus shouldn't be
placed on the bus.
This problem is flagged by the compiler as follows:
$ make dtbs W=1
...
DTC arch/arm/boot/dts/r8a7792-wheat.dtb
arch/arm/boot/dts/r8a7792-blanche.dtb: Warning (simple_bus_reg): Node /soc/timer missing or empty reg/ranges property
arch/arm/boot/dts/r8a7792-wheat.dtb: Warning (simple_bus_reg): Node /soc/timer missing or empty reg/ranges property
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Sort root sub-nodes alphabetically to allow for easier maintenance
of this file.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Use newly added R-Car SDHI Gen2 fallback compat string
in the DT of the r8a7792 SoC.
This should have no run-time effect as the driver matches against
the per-SoC compat string before considering the fallback compat string.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
With the latest dtc, we get many warnings about the missing
'#reset-cells' property in these controllers, e.g.:
arch/arm/boot/dts/r8a7790-lager.dtb: Warning (resets_property): Missing property '#reset-cells' in node /clock-controller@e6150000 or bad phandle (referred from /can@e6e80000:resets[0])
arch/arm/boot/dts/r8a7792-blanche.dtb: Warning (resets_property): Missing property '#reset-cells' in node /soc/clock-controller@e6150000 or bad phandle (referred from /soc/dma-controller@e6700000:resets[0])
arch/arm/boot/dts/r8a7792-wheat.dtb: Warning (resets_property): Missing property '#reset-cells' in node /soc/clock-controller@e6150000 or bad phandle (referred from /soc/ethernet@e6800000:resets[0])
arch/arm/boot/dts/r8a7793-gose.dtb: Warning (resets_property): Missing property '#reset-cells' in node /clock-controller@e6150000 or bad phandle (referred from /gpio@e6050000:resets[0])
arch/arm/boot/dts/r8a7794-alt.dtb: Warning (resets_property): Missing property '#reset-cells' in node /clock-controller@e6150000 or bad phandle (referred from /i2c@e6500000:resets[0])
arch/arm/boot/dts/r8a7794-silk.dtb: Warning (resets_property): Missing property '#reset-cells' in node /clock-controller@e6150000 or bad phandle (referred from /interrupt-controller@e61c0000:resets[0])
This adds it for the three r8a779x chips that were lacking it. The
binding mandates this as <1>, so this is the value I use.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[geert: Add fix for r8a7793.dtsi]
Fixes: 34fbd2b127 ("ARM: dts: r8a7790: Add reset control properties")
Fixes: 6e11a322f1 ("ARM: dts: r8a7792: Add reset control properties")
Fixes: 84fb19e1d2 ("ARM: dts: r8a7793: Add reset control properties")
Fixes: 615beb759c ("ARM: dts: r8a7794: Add reset control properties")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Currently only the primary CPU in the CA15 cluster has a clocks
property, while the secondary CPU core is driven by the same clock.
Add the missing clocks property to fix this.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Use newly added R-Car GPIO Gen2 fallback compat string
in place of now deprecated non-generation specific
R-Car GPIO fallback compat string in the DT of the r8a7792 SoC.
This should have no run-time effect as the driver matches against
the per-SoC compat string before considering the fallback compat string.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Use the preferred generic node name instead of the specific name.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add properties to describe the reset topology for on-SoC devices:
- Add the "#reset-cells" property to the CPG/MSSR device node,
- Add resets and reset-names properties to the various device nodes.
This allows to reset SoC devices using the Reset Controller API.
Note that resets usually match the corresponding module clocks.
Exceptions are:
- The audio module has resets for the Serial Sound Interfaces only,
but audio is not yet enabled in r8a7792.dtsi,
- The display module has only a single reset for all DU channels, but
adding reset properties for the display is postponed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Convert the R-Car V2H SoC from the old "Renesas R-Car Gen2 Clock Pulse
Generator (CPG)" and "Renesas CPG Module Stop (MSTP) Clocks" DT bindings
to the new unified "Renesas Clock Pulse Generator / Module Standby and
Software Reset" DT bindings.
This simplifies the DTS files, and allows to add support for reset
control later.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reserve SRAM for the jump stub for CPU core bringup.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
R-Car V2H has 2 regions of Inter Connect RAM (72 + 4 KiB).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Unlike other R-Car Gen2 SoCs with Cortex-A15 CPU cores, R-Car V2H does
not have a programmable Z clock (Cortex-A15 CPU core clock), but uses a
fixed divider.
This is similar to the Z2 clock (Cortex-A7 CPU core clock) on R-Car E2.
Hence:
- Remove the Z clock output from the cpg_clocks node, as this implied
a programmable clock,
- Add the Z clock as a fixed factor clock,
- Let the first CPU node point to the new Z clock,
- Remove the Z clock index from the bindings (this definition was used
by r8a7792.dtsi only, and was not a contract between DT and driver).
Fixes: 7c4163aae3 ("ARM: dts: r8a7792: initial SoC device tree")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Link the ARM GIC to the INTC-SYS module clock, and add it to the "always
on" PM Domain, so it can be power managed using that clock.
Note that currently the GIC-400 driver doesn't support module clocks nor
Runtime PM, so this must be handled as a critical clock.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The Cortex-A15 cache controller is an integrated controller, and thus
the device node representing it should not have a unit-addresses or reg
property.
Fixes: 7c4163aae3 ("ARM: dts: r8a7792: initial SoC device tree")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Since everybody copied my own mistake from the DT binding example,
let's address all the offenders in one swift go.
Most of them got the CPU interface size wrong (4kB, while it should
be 8kB), except for both keystone platforms which got the control
interface wrong (4kB instead of 8kB).
In a few cases where I knew for sure what implementation was used,
I've added the "arm,gic-400" compatible string. I'm 99% sure that
this is what everyone is using, but short of having the TRM for
all the other SoCs, I've left them alone.
Acked-by: Shawn Guo <shawnguo@kernel.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Matthias Brugger <matthias.bgg@gmail.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Use recently added R-Car Gen 2 fallback binding for msiof nodes in
DT for r8a7792 SoC.
This has no run-time effect for the current driver as the initialisation
sequence is the same for the SoC-specific binding for r8a7792 and the
fallback binding for R-Car Gen 2.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Use recently added R-Car Gen 2 fallback binding for i2c nodes in
DT for r8a7792 SoC.
This has no run-time effect for the current driver as the initialisation
sequence is the same for the SoC-specific binding for r8a7792 and the
fallback binding for R-Car Gen 2.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Lots of changes as usual, so I'm trying to be brief here. Most of the
new hardware support has the respective driver changes merged through
other trees or has had it available for a while, so this is where things
come together.
We get a DT descriptions for a couple of new SoCs, all of them variants
of other chips we already support, and usually coming with a new
evaluation board:
- Oxford semiconductor (now Broadcom) OX820 SoC for NAS devices
- Qualcomm MDM9615 LTE baseband
- NXP imx6ull, the latest and smallest i.MX6 application processor variant
- Renesas RZ/G (r8a7743 and r8a7745) application processors
- Rockchip PX3, a variant of the rk3188 chip used in Android tablets
- Rockchip rk1108 single-core application processor
- ST stm32f746 Cortex-M7 based microcontroller
- TI DRA71x automotive processors
These are commercially available consumer platforms we now support:
- Motorola Droid 4 (xt894) mobile phone
- Rikomagic MK808 Android TV stick based on Rockchips rx3066
- Cloud Engines PogoPlug v3 based on OX820
- Various Broadcom based wireless devices:
- Netgear R8500 router
- Tenda AC9 router
- TP-LINK Archer C9 V1
- Luxul XAP-1510 Access point
- Turris Omnia open hardware router based on Armada 385
And a couple of new boards targeted at developers, makers
or industrial integration:
- Macnica Sodia development platform for Altera socfpga (Cyclone V)
- MicroZed board based on Xilinx Zynq FPGA platforms
- TOPEET itop/elite based on exynos4412
- WP8548 MangOH Open Hardware platform for IOT, based on
Qualcomm MDM9615
- NextThing CHIP Pro gadget
- NanoPi M1 development board
- AM571x-IDK industrial board based on TI AM5718
- i.MX6SX UDOO Neo
- Boundary Devices Nitrogen6_SOM2 (i.MX6)
- Engicam i.CoreM6
- Grinn i.MX6UL liteSOM/liteBoard
- Toradex Colibri iMX6 module
Other changes:
- added peripherals on renesas, davinci, stm32f429, uniphier, sti,
mediatek, integrator, at91, imx, vybrid, ls1021a, omap, qualcomm,
mvebu, allwinner, broadcom, exynos, zynq
- Continued fixes for W=1 dtc warnings
- The old STiH415/416 SoC support gets removed, these never made it into
products and have served their purpose in the kernel as a template
for teh newer chips from ST
- The exynos4415 dtsi file is removed as nothing uses it.
- Intel PXA25x can now be booted using devicetree
Conflicts:
arch/arm/boot/dts/r8a*.dtsi: a node was added
the clk tree, keep both sides and watch out for git
dropping the required '};' at the end of each side.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=wJt3
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM DT updates from Arnd Bergmann:
"Lots of changes as usual, so I'm trying to be brief here. Most of the
new hardware support has the respective driver changes merged through
other trees or has had it available for a while, so this is where
things come together.
We get a DT descriptions for a couple of new SoCs, all of them
variants of other chips we already support, and usually coming with a
new evaluation board:
- Oxford semiconductor (now Broadcom) OX820 SoC for NAS devices
- Qualcomm MDM9615 LTE baseband
- NXP imx6ull, the latest and smallest i.MX6 application processor variant
- Renesas RZ/G (r8a7743 and r8a7745) application processors
- Rockchip PX3, a variant of the rk3188 chip used in Android tablets
- Rockchip rk1108 single-core application processor
- ST stm32f746 Cortex-M7 based microcontroller
- TI DRA71x automotive processors
These are commercially available consumer platforms we now support:
- Motorola Droid 4 (xt894) mobile phone
- Rikomagic MK808 Android TV stick based on Rockchips rx3066
- Cloud Engines PogoPlug v3 based on OX820
- Various Broadcom based wireless devices:
- Netgear R8500 router
- Tenda AC9 router
- TP-LINK Archer C9 V1
- Luxul XAP-1510 Access point
- Turris Omnia open hardware router based on Armada 385
And a couple of new boards targeted at developers, makers or
industrial integration:
- Macnica Sodia development platform for Altera socfpga (Cyclone V)
- MicroZed board based on Xilinx Zynq FPGA platforms
- TOPEET itop/elite based on exynos4412
- WP8548 MangOH Open Hardware platform for IOT, based on Qualcomm MDM9615
- NextThing CHIP Pro gadget
- NanoPi M1 development board
- AM571x-IDK industrial board based on TI AM5718
- i.MX6SX UDOO Neo
- Boundary Devices Nitrogen6_SOM2 (i.MX6)
- Engicam i.CoreM6
- Grinn i.MX6UL liteSOM/liteBoard
- Toradex Colibri iMX6 module
Other changes:
- added peripherals on renesas, davinci, stm32f429, uniphier, sti,
mediatek, integrator, at91, imx, vybrid, ls1021a, omap, qualcomm,
mvebu, allwinner, broadcom, exynos, zynq
- Continued fixes for W=1 dtc warnings
- The old STiH415/416 SoC support gets removed, these never made it
into products and have served their purpose in the kernel as a
template for teh newer chips from ST
- The exynos4415 dtsi file is removed as nothing uses it.
- Intel PXA25x can now be booted using devicetree"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (422 commits)
arm: dts: zynq: Add MicroZed board support
ARM: dts: da850: enable high speed for mmc
ARM: dts: da850: Add node for pullup/pulldown pinconf
ARM: dts: da850: enable memctrl and mstpri nodes per board
ARM: dts: da850-lcdk: Add ethernet0 alias to DT
ARM: dts: artpec: add pcie support
ARM: dts: add support for Turris Omnia
devicetree: Add vendor prefix for CZ.NIC
ARM: dts: berlin2q-marvell-dmp: fix typo in chosen node
ARM: dts: berlin2q-marvell-dmp: fix regulators' name
ARM: dts: Add xo to sdhc clock node on qcom platforms
ARM: dts: r8a7794: Add device node for PRR
ARM: dts: r8a7793: Add device node for PRR
ARM: dts: r8a7792: Add device node for PRR
ARM: dts: r8a7791: Add device node for PRR
ARM: dts: r8a7790: Add device node for PRR
ARM: dts: r8a7779: Add device node for PRR
ARM: dts: r8a73a4: Add device node for PRR
ARM: dts: sk-rzg1e: add Ether support
ARM: dts: sk-rzg1e: initial device tree
...
Add a device node for the Product Register, which provides SoC product
and revision information.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the generic R8A7792 parts of the MSIOF0/1 device nodes.
Based on the original (and large) patch by Vladimir Barinov
<vladimir.barinov@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe the MSIOF0/1 clocks and their parent, MP clock in the R8A7792
device tree.
Based on the original (and large) patch by Vladimir Barinov
<vladimir.barinov@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a device node for the RST module, which provides a.o. reset control
and mode pin monitoring.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Define the generic R8A7792 part of the QSPI device node.
Based on the original (and large) patch by Vladimir Barinov
<vladimir.barinov@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe the QSPI clock in the R8A7792 device tree.
Based on the original (and large) patch by Vladimir Barinov
<vladimir.barinov@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe 3 instances (VSPS, VSPD0, and VSPD1) of the VSP1V in the R8A7792
device tree.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe the VSP1V clocks in the R8A7792 device tree.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the generic R8A7792 part of the DU device node.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe the DU0/1 clocks and their parent, ZX clock in the R8A7792 device
tree.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Commit 2a0900655d5e (ARM: dts: r8a7792: add I2C support) had a wrongly
indented line at the end of the "aliases" subnode -- fix it.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the generic R8A7792 parts of the VIN[0-5] device nodes.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe the VIN[0-5] clocks and their parent, ZG clock in the R8A7792
device tree.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the generic R8A7792 parts of the I2C[0-5] device nodes.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe the I2C[0-5] clocks in the R8A7792 device tree.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the generic R8A7792 part of the SDHI0 device node.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Geert Uytterhoeven
Yoshihiro Shimoda
Magnus Damm
Marek Vasut
Magnus Damm
Laurent Pinchart
Wolfram Sang
Fabrizio Castro
Simon Horman
Olof Johansson
Arnd Bergmann
Marc Zyngier
Linus Torvalds
Sergei Shtylyov