Introduce basic support for the Freescale P1022DS reference board, based on the
Freescale BSP for this board. This patch excludes the DIU, SSI, and MMC/SD
drivers. Only a 36-bit DTS is provided.
Update mpc86xx_smp_defconfig and mpc85xx_defconfig to support the P1022DS.
This means enabling 64-bit physical address support, increasing the maximum
zone order to 12 (to allow the DIU driver to allocate large chunks), and
clean up the audio options to disable the deprecated OSS support.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
By default ti1520 bridge expects an input clock on CLOCK pin (to control
power chip). However on this boards CLOCK should be generated by PCI1520
itself. Add a quirk that enables internal 16 KHz clock generation on
this pin.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The mpc85xx_mds_setup_arch() function is incomprehensible
and unmaintainable. Factor out all QE specific stuff into
mpc85xx_mds_qe_init() and mpc85xx_mds_reset_ucc_phys().
Also move QE stuff out of mpc85xx_mds_pic_init().
The diff is unreadable, but only because the code was so. ;-)
It should be better now, and less indented.
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
P1021 processors have no dedicated ROM to store the QE microcode,
so the fimrware is stored externally, and it is U-Boot responsibility
to load it. It might be that the board is booting without QE, e.g.
currently U-Boot doesn't support QE for P1021MDS boards, which means
that QE isn't initialized, and so the board hangs early at boot.
This patch fixes the issue by marking QE as disabled and checking the
state in the probing code. U-Boot should fixup the state if it
initialized the QE.
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The code inside '#ifdef CONFIG_QUICC_ENGINE' makes the
mpc85xx_mds_setup_arch() return early if no QE nodes present,
and so SWIOTLB is never initialized.
This patch fixes the issue by moving SWIOTLB code above
QE.
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Adds support for kexec on 85xx machines for the BookE platform.
Including support for SMP machines
Based off work from Maxim Uvarov <muvarov@mvista.com>
Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
via following scripts
FILES=$(find * -type f | grep -vE 'oprofile|[^K]config')
sed -i \
-e 's/lmb/memblock/g' \
-e 's/LMB/MEMBLOCK/g' \
$FILES
for N in $(find . -name lmb.[ch]); do
M=$(echo $N | sed 's/lmb/memblock/g')
mv $N $M
done
and remove some wrong change like lmbench and dlmb etc.
also move memblock.c from lib/ to mm/
Suggested-by: Ingo Molnar <mingo@elte.hu>
Acked-by: "H. Peter Anvin" <hpa@zytor.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The doorbells use the content of the PIR register to match messages
from other CPUs. This may or may not be the same as our linux CPU
number, so using that as the "target" is no right.
Instead, we sample the PIR register at boot on every processor
and use that value subsequently when sending IPIs.
We also use a per-cpu message mask rather than a global array which
should limit cache line contention.
Note: We could use the CPU number in the device-tree instead of
the PIR register, as they are supposed to be equivalent. This
might prove useful if doorbells are to be used to kick CPUs out
of FW at boot time, thus before we can sample the PIR. This is
however not the case now and using the PIR just works.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently some MPC85xx and MPC86xx boards fail to build without
CONFIG_PCI:
arch/powerpc/platforms/fsl_uli1575.c: In function 'quirk_final_uli5249':
arch/powerpc/platforms/fsl_uli1575.c:234: error: implicit declaration of function 'pci_bus_for_each_resource'
arch/powerpc/platforms/fsl_uli1575.c:234: error: expected ';' before '{' token
cc1: warnings being treated as errors
arch/powerpc/platforms/fsl_uli1575.c:223: warning: unused variable 'dummy'
make[1]: *** [arch/powerpc/platforms/fsl_uli1575.o] Error 1
This patch fixes the issue by appending 'if PCI' condition when
selecting FSL_ULI1575 Kconfig symbol.
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Interrupt controllers' hooks are executed in the atomic context, so
they are not permitted to sleep (with RT kernels non-raw spinlocks are
sleepable). So, socrates_fpga_pic_lock has to be a real (non-sleepable)
spinlock.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* 'next-devicetree' of git://git.secretlab.ca/git/linux-2.6: (41 commits)
of: remove undefined request_OF_resource & release_OF_resource
of/sparc: Remove sparc-local declaration of allnodes and devtree_lock
of: move definition of of_chosen into common code.
of: remove unused extern reference to devtree_lock
of: put default string compare and #a/s-cell values into common header
of/flattree: Don't assume HAVE_LMB
of: protect linux/of.h with CONFIG_OF
proc_devtree: fix THIS_MODULE without module.h
of: Remove old and misplaced function declarations
of/flattree: Make the kernel accept ePAPR style phandle information
of/flattree: endian-convert members of boot_param_header
of: assume big-endian properties, adding conversions where necessary
of: use __be32 for cell value accessors
of/flattree: use OF_ROOT_NODE_{SIZE,ADDR}_CELLS DEFAULT for fdt parsing
of/flattree: use callback to setup initrd from /chosen
proc_devtree: include linux/of.h
of: make set_node_proc_entry private to proc_devtree.c
of: include linux/proc_fs.h
of/flattree: merge early_init_dt_scan_memory() common code
of: add 'of_' prefix to machine_is_compatible()
...
This patch adds NOR Flash, LEDs and PIB support for MPC8568E-MDS
boards. Plus, move bcsr node into localbus node, and add bcsr5
gpio-controller node.
Some platform code modifications were also needed.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Now we use printf style alignment there is no need to manually space
these fields.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Recent U-Boot commit 5ccd29c3679b3669b0bde5c501c1aa0f325a7acb caused
the "cpu-release-addr" device tree property to contain the physical RAM
location that secondary cores were spinning at. Previously, the
"cpu-release-addr" property contained a value referencing the boot page
translation address range of 0xfffffxxx, which then indirectly accessed
RAM.
The "cpu-release-addr" is currently ioremapped and the secondary cores
kicked. However, due to the recent change in "cpu-release-addr", it
sometimes points to a memory location in low memory that cannot be
ioremapped. For example on a P2020-based board with 512MB of RAM the
following error occurs on bootup:
<...>
mpic: requesting IPIs ...
__ioremap(): phys addr 0x1ffff000 is RAM lr c05df9a0
Unable to handle kernel paging request for data at address 0x00000014
Faulting instruction address: 0xc05df9b0
Oops: Kernel access of bad area, sig: 11 [#1]
SMP NR_CPUS=2 P2020 RDB
Modules linked in:
<... eventual kernel panic>
Adding logic to conditionally ioremap or access memory directly resolves
the issue.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Nate Case <ncase@xes-inc.com>
Reported-by: Dipen Dudhat <B09055@freescale.com>
Tested-by: Dipen Dudhat <B09055@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
MPC85xx chips report the wrong value in feature reporting register,
and that causes the following oops:
Unable to handle kernel paging request for data at address 0x00000c00
Faulting instruction address: 0xc0019294
Oops: Kernel access of bad area, sig: 11 [#1]
MPC8569 MDS
Modules linked in:
[...]
NIP [c0019294] mpic_set_irq_type+0x2f0/0x368
LR [c0019124] mpic_set_irq_type+0x180/0x368
Call Trace:
[ef851d60] [c0019124] mpic_set_irq_type+0x180/0x368 (unreliable)
[ef851d90] [c007958c] __irq_set_trigger+0x44/0xd4
[ef851db0] [c007b550] set_irq_type+0x40/0x7c
[ef851dc0] [c0004a60] irq_create_of_mapping+0xb4/0x114
[ef851df0] [c0004af0] irq_of_parse_and_map+0x30/0x40
[ef851e20] [c0405678] fsl_of_msi_probe+0x1a0/0x328
[ef851e60] [c02e6438] of_platform_device_probe+0x5c/0x84
[...]
This is because mpic_alloc() assigns wrong values to
mpic->isu_{size,shift,mask}, and things eventually break when
_mpic_irq_read() is trying to use them.
This patch fixes the issue by enabling MPIC_BROKEN_FRR_NIRQS quirk.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
machine is compatible is an OF-specific call. It should have
the of_ prefix to protect the global namespace.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Frans Pop <elendil@planet.nl>
Cc: linuxppc-dev@ozlabs.org
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Recent U-Boot commit 5ccd29c3679b3669b0bde5c501c1aa0f325a7acb caused
the "cpu-release-addr" device tree property to contain the physical RAM
location that secondary cores were spinning at. Previously, the
"cpu-release-addr" property contained a value referencing the boot page
translation address range of 0xfffffxxx, which then indirectly accessed
RAM.
The "cpu-release-addr" is currently ioremapped and the secondary cores
kicked. However, due to the recent change in "cpu-release-addr", it
sometimes points to a memory location in low memory that cannot be
ioremapped. For example on a P2020-based board with 512MB of RAM the
following error occurs on bootup:
<...>
mpic: requesting IPIs ...
__ioremap(): phys addr 0x1ffff000 is RAM lr c05df9a0
Unable to handle kernel paging request for data at address 0x00000014
Faulting instruction address: 0xc05df9b0
Oops: Kernel access of bad area, sig: 11 [#1]
SMP NR_CPUS=2 P2020 RDB
Modules linked in:
<... eventual kernel panic>
Adding logic to conditionally ioremap or access memory directly resolves
the issue.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Nate Case <ncase@xes-inc.com>
Reported-by: Dipen Dudhat <B09055@freescale.com>
Tested-by: Dipen Dudhat <B09055@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The wrong variable was returned in the case of an error.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Writing a driver using SCLPC on the MPC5200B I detected, that the
intspec arrays to map irqs to Linux virq cannot be const, because the
mapping and xlate functions only take non const pointers. All those
functions do not modify the intspec, so a const pointer could be used.
Signed-off-by: Roman Fietze <roman.fietze@telemotive.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The typename member of struct irq_chip was kept for migration purposes
and is obsolete since more than 2 years. Fix up the leftovers.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: linuxppc-dev@ozlabs.org
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Add basic support for the P4080 DS reference board. None of the data
path devices (ethernet, crypto, pme) are support at this time.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
- Add power management controller nodes;
- Add interrupts for RTC nodes, the RTC interrupt may be used as a
wakeup source;
- Add sleep properties (DEVDISR bit mask) and sleep-nexus nodes.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
P1020 is another member of Freescale QorIQ series of processors.
It is an e500 based dual core SOC.
Being a scaled down version of P2020 it has following differences from P2020:
- 533MHz - 800MHz core frequency.
- 256Kbyte L2 cache
- Ethernet controllers with classification capabilities(new controller).
From board perspective P1020RDB is same as P2020RDB.
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch creates the dts files for each core and splits the devices
between the two cores for P2020RDB.
core0 has memory, L2, i2c, spi, dma1, usb, eth0, eth1, crypto,
global-util, pci0,
core1 has L2, dma2, eth0, pci1, msi.
MPIC is shared between two cores but each core will protect its
interrupts from other core by using "protected-sources" of mpic.
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
get_irq_desc() is a powerpc-specific version of irq_to_desc(). That
is reason enough to remove it, but it also doesn't know about sparse
irq_desc support which irq_to_desc() does (when we enable it).
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The following commit introduced a compile error since it removed
the implementation of smp_85xx_basic_setup:
commit 77c0a700c1
Author: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Date: Fri Aug 28 14:25:04 2009 +1000
powerpc: Properly start decrementer on BookE secondary CPUs
Make it so that smp_ops probe() and setup_cpu() can be set to NULL.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This moves the code to start the decrementer on 40x and BookE into
a separate function which is now called from time_init() and
secondary_time_init(), before the respective clock sources are
registered. We also remove the 85xx specific code for doing it
from the platform code.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Now swiotlb_pci_dma_ops is identical to swiotlb_dma_ops; we can use
swiotlb_dma_ops with any devices. This removes swiotlb_pci_dma_ops.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch adds max_direct_dma_addr to struct dev_archdata to remove
addr_needs_map in struct dma_mapping_ops. It also converts
dma_capable() to use max_direct_dma_addr.
max_direct_dma_addr is initialized in pci_dma_dev_setup_swiotlb(),
called via ppc_md.pci_dma_dev_setup hook.
For further information:
http://marc.info/?t=124719060200001&r=1&w=2
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
- Add gpio-controller node for BCSR17, it is used to control USB
speed and VBUS;
- Add timer node for QE GTM, needed for USB host;
- Add usb node itself;
- Add some probing code for BCSR GPIOs.
NOTE: QE USB doesn't work on prototype boards, but should work on
pilot boards if specs and schematics are correct, though we
don't have the pilot boards to actually test it.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The existing fsl_rstcr_restart function is not applicable to the
mpc8560. The Global Utilities Block on this earlier CPU doesn't have
the control/reset register at 0xe00b0. This implements a board
specific reset function that uses the RCR(Reset Control Register) of
the sbc8560's EPLD to do a reset.
Signed-off-by: Liang Li <Liang.Li@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Those definitions are currently declared extern in the .c file where
they are used, move them to a header file instead.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Linux isn't able to detect link changes on ethernet ports that were
used by U-Boot. This is because U-Boot wrongly clears interrupt
polarity bit (INTPOL, 0x400) in the extended status register (EXT_SR,
0x1b) of Marvell PHYs.
There is no easy way for PHY drivers to know IRQ line polarity (we
could extract it from the device tree and pass it to phydevs, but
that'll be quite a lot of work), so for now just reset the PHYs to
their default states.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
FSL RapidIO won't probe without a proper compatible entry. This
patch fixes the issue by adding fsl,rapidio-delta compatible to
mpc85xx_ids.
Signed-off-by: Randy Vinson <rvinson@mvista.com>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Match what other 85xx platforms do for of_platform_bus_probe and use
machine_device_initcall. This is one small step in killing of
ppc_md.init.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add support for X-ES single-board computers based on the Freescale
MPC85xx processors.
Signed-off-by: Nate Case <ncase@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add the platform-specific code for enabling SWIOTLB if needed on P2020DS,
MPC85xx DS, and MPC85xx MDS boards as they are capable of having >4G of
memory.
We determine if we need to enable swiotlb based on how much memory is in
the board and if it exceeds 4G or what we can map via PCI inbound
windows.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The P2020 is a dual e500v2 core based SOC with:
* 3 PCIe controllers
* 2 General purpose DMA controllers
* 2 sRIO controllers
* 3 eTSECS
* USB 2.0
* SDHC
* SPI, I2C, DUART
* enhanced localbus
* and optional Security (P2020E) security w/XOR acceleration
The p2020 DS reference board is pretty similar to the existing MPC85xx
DS boards and has a ULI 1575 connected on one of the PCIe controllers.
Signed-off-by: Ted Peters <Ted.Peters@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Benjamin Herrenschmidt
Timur Tabi
Dmitry Eremin-Solenikov
Anton Vorontsov
Matthew McClintock
Yinghai Lu
Haiying Wang
Anton Vorontsov
David S. Miller
Linus Torvalds
Anton Blanchard
Peter Tyser
Grant Likely
Frans Pop
Liu Yu-B13201
Roel Kluin
Roman Fietze
Thomas Gleixner
Kumar Gala
Poonam Aggrwal
Michael Ellerman
FUJITA Tomonori
Liang Li
Huang Weiyi
Randy Vinson
Nate Case