The the pin groups and pin functions have been changed
in atlas7 step B soc. We have to update the driver
to support step B chip.
Changes:
1. add 5 jtag pins to IOC_TOP:
"jtag_tdo", "jtag_tms","jtag_tck", "jtag_tdi", "jtag_trstn"
these 5 pins can be mutiplex with other functions, so we
have to conver these 5 pins in pinmux.
2. add pin groups for audio digmic, audio spdif, can transceiver
en, can transceiver stb, i2s0, i2s1 and jtag.
3. serval pins can be located to more PADs:
audio_uart0_urfs, audio_uart1_urfs, audio_uart2_urfs,
audio_uart2_urxd, audio_uart2_usclk, audio_uart2_utfs,
audio_uart2_utxd, can0_rxd, can0_txd, can1_rxd, can1_txd
jtag_ntrst, jtag_swdiotms, jtag_tck, jtag_tdi, jtag_tdo,
pw_cko0, pw_cko1, pw_i2s01, pw_pwm0, pw_pwm1, sd2_cdb,
sd2_wpb, uart2_cts, uart2_rts, uart2_rxd, uart2_txd,
uart3_cts, uart3_rts, uart3_rxd, uart3_txd, uart4_cts,
uart4_rts, usb0_drvvbus, usb1_drvvbus.
Because of Changes#3, some functions should have more than one
pin groups. So we have to split the original pin group to serval
pin groups.
For example:
audio_uart0 has 5 pins, on STEPA, each of these 5 pins only has
one related PAD. But on STEPB, audio_uart0_urfs has 4 related
PAD.
So we place the 4 pins with one PAD into a single pin group:
audio_uart0_basic_group.
and place urfs pin wtih different PADs to 4 different pin groups:
audio_uart0_urfs_group0, ..., audio_uart0_urfs_group3
A full audio_uart0 pin group can be:
pinctrl-0 = <&audio_uart0_basic_group &audio_uart0_urfs_group0>;
If audio_uart0 pin group encountered some confiction, we only have
to change the urfs group:
pinctrl-0 = <&audio_uart0_basic_group &audio_uart0_urfs_group2>;
Signed-off-by: Wei Chen <Wei.Chen@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Most interrupt flow handlers do not use the irq argument. Those few
which use it can retrieve the irq number from the irq descriptor.
Remove the argument.
Search and replace was done with coccinelle and some extra helper
scripts around it. Thanks to Julia for her help!
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
To set/get atlas7 pull & drive strength, we use lots of if/else
to check pad type. But except mask value or immediate value, all
actions in these conditional branches are the same.
So we use predefined pull info table and drive strength table
to reduce these redundancy code.
Signed-off-by: Wei Chen <Wei.Chen@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We had not implemented the pm interface of atlas7 pinctrl
and gpio drivers. So when system resumes from sleep, all
pin configuration and gpio status will be lost.
Now, we implement these interfaces to support pm.
At the same time, this patch also drops a lot of if-else
by look-up table for getting and setting pull.
Signed-off-by: Wei Chen <Wei.Chen@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The irq argument of most interrupt flow handlers is unused or merily
used instead of a local variable. The handlers which need the irq
argument can retrieve the irq number from the irq descriptor.
Search and update was done with coccinelle and the invaluable help of
Julia Lawall.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-gpio@vger.kernel.org
Use irq_desc_get_xxx() to avoid redundant lookup of irq_desc while we
already have a pointer to corresponding irq_desc.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
platform_driver does not need to set an owner because
platform_driver_register() will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currently, pinctrl_register() just returns NULL on error, so the
callers can not know the exact reason of the failure.
Some of the pinctrl drivers return -EINVAL, some -ENODEV, and some
-ENOMEM on error of pinctrl_register(), although the error code
might be different from the real cause of the error.
This commit reworks pinctrl_register() to return the appropriate
error code and modifies all of the pinctrl drivers to use IS_ERR()
for the error checking and PTR_ERR() for getting the error code.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Lee Jones <lee@kernel.org>
Acked-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Ray Jui <rjui@broadcom.com>
Acked-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Hongzhou Yang <hongzhou.yang@mediatek.com>
Acked-by: Wei Chen <Wei.Chen@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
platform_driver does not need to set the owner field, as it will be
populated by the driver core, so just remove it.
The semantic patch that makes this change is available
in scripts/coccinelle/api/platform_no_drv_owner.cocci.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Pinctrl module (ioc) controls the Pad's function select
(each pad can have 8 functions), Pad's Drive Strength, Pad's
Pull Select and Pad's Input Disable status.
The ioc has two modules, ioc_top & ioc_rtc. Both of these two
modules have function select/clear, Pull select and Drive
Strength registers. But only ioc_rtc has input-disable
registers. The Pads on ioc_top have to access ioc_rtc to set
their input-disable status and intpu-disable-value.
So have to use one ioc driver instance to drive these two
ioc modules at the same time, and each ioc module will be
treat as one bank on the "IOC Device".
The GPIO Controller controls the GPIO status if the Pad has
been config as GPIO by Pinctrl already. Includes the GPIO
Input/output, Interrupt type, Interrupt Status, and Set/Get
Values.
The GPIO pull up/down are controlled by Pinctrl.
There are 7 GPIO Groups and splited into 3 MACROs in atlas7.
The GPIO Groups in one MACRO share one GPIO controllers, each
GPIO Group are treated as one GPIO bank.
For example:
In VDIFM macro, there is one GPIO Controller, it has 3 banks
to control 3 gpio groups. Its gpio name space is from 0 to 95.
The Device Tree can be written as following:
gpio-ranges = <&pinctrl 0 0 0>,
<&pinctrl 32 0 0>,
<&pinctrl 64 0 0>;
gpio-ranges-group-names = "gnss_gpio_grp",
"lcd_vip_gpio_grp",
"sdio_i2s_gpio_grp";
bank#0 is from 0~31, the pins are from pinctrl's "gnss_gpio_grp".
bank#2 is from 32~63, the pins are from pinctrl's "lcd_vip_gpio_grp".
bank#3 is from 64~95, the pins are from pinctrl's "sdio_i2s_gpio_grp".
Signed-off-by: Wei Chen <Wei.Chen@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Instead of referring to a global static variable for the sgpio
locking, use the state container to contain the lock.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
marco chip has been dropped, clear its support.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
cycle:
- Increase the default ARCH_NR_GPIO from 256 to 512. This
was done to avoid having a custom <asm/gpio.h> header for
the x86 architecture - GPIO is custom and complicated
enough as it is already! We want to move to a radix to
store the descriptors going forward, and finally get rid
of this fixed array size altogether.
- Endgame patching of the gpio_remove() semantics initiated
by Abdoulaye Berthe. It is not accepted by the system that
the removal of a GPIO chip fails during e.g. reboot or
shutdown, and therefore the return value has now painfully
been refactored away. For special cases like GPIO expanders
on a hot-pluggable bus like USB, we may later add some
gpiochip_try_remove() call, but for the cases we have now,
return values are moot.
- Some incremental refactoring of the gpiolib core and ACPI
GPIO library for more descriptor usage.
- Refactor the chained IRQ handler set-up method to handle
also threaded, nested interrupts and set up the parent IRQ
correctly. Switch STMPE and TC3589x drivers to use this
registration method.
- Add a .irq_not_threaded flag to the struct gpio_chip, so
that also GPIO expanders that block but are still not
using threaded IRQ handlers.
- New drivers for the ARM64 X-Gene SoC GPIO controller.
- The syscon GPIO driver has been improved to handle the
"DSP GPIO" found on the TI Keystone 2 SoC:s.
- ADNP driver switched to use gpiolib irqchip helpers.
- Refactor the DWAPB driver to support being instantiated
from and MFD cell (platform device).
- Incremental feature improvement in the Zynq, MCP23S08,
DWAPB, OMAP, Xilinx and Crystalcove drivers.
- Various minor fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=8InA
-----END PGP SIGNATURE-----
Merge tag 'gpio-v3.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO changes from Linus Walleij:
"This is the bulk of GPIO changes for the v3.18 development cycle:
- Increase the default ARCH_NR_GPIO from 256 to 512. This was done
to avoid having a custom <asm/gpio.h> header for the x86
architecture - GPIO is custom and complicated enough as it is
already! We want to move to a radix to store the descriptors going
forward, and finally get rid of this fixed array size altogether.
- Endgame patching of the gpio_remove() semantics initiated by
Abdoulaye Berthe. It is not accepted by the system that the
removal of a GPIO chip fails during eg reboot or shutdown, and
therefore the return value has now painfully been refactored away.
For special cases like GPIO expanders on a hot-pluggable bus like
USB, we may later add some gpiochip_try_remove() call, but for the
cases we have now, return values are moot.
- Some incremental refactoring of the gpiolib core and ACPI GPIO
library for more descriptor usage.
- Refactor the chained IRQ handler set-up method to handle also
threaded, nested interrupts and set up the parent IRQ correctly.
Switch STMPE and TC3589x drivers to use this registration method.
- Add a .irq_not_threaded flag to the struct gpio_chip, so that also
GPIO expanders that block but are still not using threaded IRQ
handlers.
- New drivers for the ARM64 X-Gene SoC GPIO controller.
- The syscon GPIO driver has been improved to handle the "DSP GPIO"
found on the TI Keystone 2 SoC:s.
- ADNP driver switched to use gpiolib irqchip helpers.
- Refactor the DWAPB driver to support being instantiated from and
MFD cell (platform device).
- Incremental feature improvement in the Zynq, MCP23S08, DWAPB, OMAP,
Xilinx and Crystalcove drivers.
- Various minor fixes"
* tag 'gpio-v3.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (52 commits)
gpio: pch: Build context save/restore only for PM
pinctrl: abx500: get rid of unused variable
gpio: ks8695: fix 'else should follow close brace '}''
gpio: stmpe: add verbose debug code
gpio: stmpe: fix up interrupt enable logic
gpio: staticize xway_stp_init()
gpio: handle also nested irqchips in the chained handler set-up
gpio: set parent irq on chained handlers
gpiolib: irqchip: use irq_find_mapping while removing irqchip
gpio: crystalcove: support virtual GPIO
pinctrl: bcm281xx: make Kconfig dependency more strict
gpio: kona: enable only on BCM_MOBILE or for compile testing
gpio, bcm-kona, LLVMLinux: Remove use of __initconst
gpio: Fix ngpio in gpio-xilinx driver
gpio: dwapb: fix pointer to integer cast
gpio: xgene: Remove unneeded #ifdef CONFIG_OF guard
gpio: xgene: Remove unneeded forward declation for struct xgene_gpio
gpio: xgene: Fix missing spin_lock_init()
gpio: ks8695: fix switch case indentation
gpiolib: add irq_not_threaded flag to gpio_chip
...
Some drivers accidentally still use the return value from
gpiochip_remove(). Get rid of them so we can simplify this function
and get rid of the return value.
Cc: Abdoulaye Berthe <berthe.ab@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
we have done that for atlas6 in commit ed36c1a, 086b8904 etc. here we
do same things for prima2.
Signed-off-by: Rongjun Ying <rongjun.ying@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
commit 2243a87d90
"pinctrl: avoid duplicated calling enable_pinmux_setting for a pin"
removed the .disable callback from the struct pinmux_ops,
making the .enable() callback the only remaining callback.
However .enable() is a bad name as it seems to imply that a
muxing can also be disabled. Rename the callback to .set_mux()
and also take this opportunity to clean out any remaining
mentions of .disable() from the documentation.
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Acked-by: Fan Wu <fwu@marvell.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The I2S controller can use the external clock as reference clock with
master mode. But based on different hardware or software design, this
external clock might be needed or not needed.
So the external input pin can be an independent pinctrl group, and the
card driver can decice to get it or not.
Signed-off-by: Rongjun Ying <rongjun.ying@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The I2S controller can output mclk to external audio codec. But by
hardware design, some codecs need mclk and some codecs do not need
mclk. So the mclk pin can be an independent pinctrl group, and the
card driver can get it or not based on boards.
Signed-off-by: Rongjun Ying <rongjun.ying@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
According to key customer's requirement, fix "line over 80
characters".
Signed-off-by: Bin Shi <Bin.Shi@csr.com>
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
What the patch does:
1. Call pinmux_disable_setting ahead of pinmux_enable_setting
each time pinctrl_select_state is called
2. Remove the HW disable operation in pinmux_disable_setting function.
3. Remove the disable ops in struct pinmux_ops
4. Remove all the disable ops users in current code base.
Notes:
1. Great thanks for the suggestion from Linus, Tony Lindgren and
Stephen Warren and Everyone that shared comments on this patch.
2. The patch also includes comment fixes from Stephen Warren.
The reason why we do this:
1. To avoid duplicated calling of the enable_setting operation
without disabling operation inbetween which will let the pin
descriptor desc->mux_usecount increase monotonously.
2. The HW pin disable operation is not useful for any of the
existing platforms.
And this can be used to avoid the HW glitch after using the
item #1 modification.
In the following case, the issue can be reproduced:
1. There is a driver that need to switch pin state dynamically,
e.g. between "sleep" and "default" state
2. The pin setting configuration in a DTS node may be like this:
component a {
pinctrl-names = "default", "sleep";
pinctrl-0 = <&a_grp_setting &c_grp_setting>;
pinctrl-1 = <&b_grp_setting &c_grp_setting>;
}
The "c_grp_setting" config node is totally identical, maybe like
following one:
c_grp_setting: c_grp_setting {
pinctrl-single,pins = <GPIO48 AF6>;
}
3. When switching the pin state in the following official pinctrl
sequence:
pin = pinctrl_get();
state = pinctrl_lookup_state(wanted_state);
pinctrl_select_state(state);
pinctrl_put();
Test Result:
1. The switch is completed as expected, that is: the device's
pin configuration is changed according to the description in the
"wanted_state" group setting
2. The "desc->mux_usecount" of the corresponding pins in "c_group"
is increased without being decreased, because the "desc" is for
each physical pin while the setting is for each setting node
in the DTS.
Thus, if the "c_grp_setting" in pinctrl-0 is not disabled ahead
of enabling "c_grp_setting" in pinctrl-1, the desc->mux_usecount
will keep increasing without any chance to be decreased.
According to the comments in the original code, only the setting,
in old state but not in new state, will be "disabled" (calling
pinmux_disable_setting), which is correct logic but not intact. We
still need consider case that the setting is in both old state
and new state. We can do this in the following two ways:
1. Avoid to "enable"(calling pinmux_enable_setting) the "same pin
setting" repeatedly
2. "Disable"(calling pinmux_disable_setting) the "same pin setting",
actually two setting instances, ahead of enabling them.
Analysis:
1. The solution #2 is better because it can avoid too much
iteration.
2. If we disable all of the settings in the old state and one of
the setting(s) exist in the new state, the pins mux function
change may happen when some SoC vendors defined the
"pinctrl-single,function-off"
in their DTS file.
old_setting => disabled_setting => new_setting.
3. In the pinmux framework, when a pin state is switched, the
setting in the old state should be marked as "disabled".
Conclusion:
1. To Remove the HW disabling operation to above the glitch mentioned
above.
2. Handle the issue mentioned above by disabling all of the settings
in old state and then enable the all of the settings in new state.
Signed-off-by: Fan Wu <fwu@marvell.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit 294d1351ff
"pinctrl: sirf: switch to using allocated state container"
caused a build conflict due to a bad conflict resolution
when cherry-picking the patch. Fix it up.
Cc: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This rewrites the SIRF pinctrl driver to allocate a state container
for the GPIO chip, just as is done for the pin controller, and
use the gpiochip_add_pin_range() to add the range from the gpiochip
side rather than adding the range from the pinctrl side.
All resulting changes are done in order to pass around a state
container rather than refer to a static global object.
Acked-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The patch 7420d2d09b12: "pinctrl: sirf: switch driver to use gpiolib
irqchip helpers" from Apr 15, 2014, leads to the following static
checker warning:
drivers/pinctrl/sirf/pinctrl-sirf.c:578 sirfsoc_gpio_handle_irq()
warn: buffer overflow 'sgpio_chip.sgpio_bank' 5 <= 31
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This switches the SiRF pinctrl driver over to using the gpiolib
irqchip helpers simplifying some of the code.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
all gpio banks are in one chip, that makes software clean in mapping
irq and gpio.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The sirfsoc_irqchip_to_bank() is obviously misnamed, as it is
not converting an irqchip to a bank but converts a gpiochip
to a bank so rename it sirfsoc_gpiochip_to_bank().
Acked-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- Merged in a branch of irqchip changes from Thomas
Gleixner: we need to have new callbacks from the
irqchip to determine if the GPIO line will be eligible
for IRQs, and this callback must be able to say "no".
After some thinking I got the branch from tglx and
have switched all current users over to use this.
- Based on tglx patches, we have added some generic
irqchip helpers in the gpiolib core. These will
help centralize code when GPIO drivers have simple
chained/cascaded IRQs. Drivers will still define
their irqchip vtables, but the gpiolib core will
take care of irqdomain set-up, mapping from local
offsets to Linux irqs, and reserve resources by
marking the GPIO lines for IRQs.
- Initially the PL061 and Nomadik GPIO/pin control
drivers have been switched over to use the new
gpiochip-to-irqchip infrastructure with more
drivers expected for the next kernel cycle. The
factoring of just two drivers still makes it worth
it so it is already a win.
- A new driver for the Synopsys DesignWare APB GPIO
block.
- Modify the DaVinci GPIO driver to be reusable also
for the new TI Keystone architecture.
- A new driver for the LSI ZEVIO SoCs.
- Delete the obsolte tnetv107x driver.
- Some incremental work on GPIO descriptors: have
gpiod_direction_output() use a logical level,
respecting assertion polarity through ACTIVE_LOW
flags, adding gpiod_direction_output_raw() for the
case where you want to set that very value. Add
gpiochip_get_desc() to fetch a GPIO descriptor from
a specific offset on a certain chip inside driver
code.
- Switch ACPI GPIO code over to using
gpiochip_get_desc() and get rid of gpio_to_desc().
- The ACPI GPIO event handling code has been reworked
after encountering an actual real life implementation.
- Support for ACPI GPIO operation regions.
- Generic GPIO chips can now be assigned labels/names
from platform data.
- We now clamp values returned from GPIO drivers to
the boolean [0,1] range.
- Some improved documentation on how to use the polarity
flag was added.
- The a large slew of incremental driver updates and
non-critical fixes. Some targeted for stable.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=8Qqf
-----END PGP SIGNATURE-----
Merge tag 'gpio-v3.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull bulk of gpio updates from Linus Walleij:
"A pretty big chunk of changes this time, but it has all been on
rotation in linux-next and had some testing. Of course there will be
some amount of fixes on top...
- Merged in a branch of irqchip changes from Thomas Gleixner: we need
to have new callbacks from the irqchip to determine if the GPIO
line will be eligible for IRQs, and this callback must be able to
say "no". After some thinking I got the branch from tglx and have
switched all current users over to use this.
- Based on tglx patches, we have added some generic irqchip helpers
in the gpiolib core. These will help centralize code when GPIO
drivers have simple chained/cascaded IRQs. Drivers will still
define their irqchip vtables, but the gpiolib core will take care
of irqdomain set-up, mapping from local offsets to Linux irqs, and
reserve resources by marking the GPIO lines for IRQs.
- Initially the PL061 and Nomadik GPIO/pin control drivers have been
switched over to use the new gpiochip-to-irqchip infrastructure
with more drivers expected for the next kernel cycle. The
factoring of just two drivers still makes it worth it so it is
already a win.
- A new driver for the Synopsys DesignWare APB GPIO block.
- Modify the DaVinci GPIO driver to be reusable also for the new TI
Keystone architecture.
- A new driver for the LSI ZEVIO SoCs.
- Delete the obsolte tnetv107x driver.
- Some incremental work on GPIO descriptors: have
gpiod_direction_output() use a logical level, respecting assertion
polarity through ACTIVE_LOW flags, adding gpiod_direction_output_raw()
for the case where you want to set that very value. Add
gpiochip_get_desc() to fetch a GPIO descriptor from a specific
offset on a certain chip inside driver code.
- Switch ACPI GPIO code over to using gpiochip_get_desc() and get rid
of gpio_to_desc().
- The ACPI GPIO event handling code has been reworked after
encountering an actual real life implementation.
- Support for ACPI GPIO operation regions.
- Generic GPIO chips can now be assigned labels/names from platform
data.
- We now clamp values returned from GPIO drivers to the boolean [0,1]
range.
- Some improved documentation on how to use the polarity flag was
added.
- a large slew of incremental driver updates and non-critical fixes.
Some targeted for stable"
* tag 'gpio-v3.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (80 commits)
gpio: rcar: Add helper variable dev = &pdev->dev
gpio-lynxpoint: force gpio_get() to return "1" and "0" only
gpio: unmap gpio irqs properly
pch_gpio: set value before enabling output direction
gpio: moxart: Actually set output state in moxart_gpio_direction_output()
gpio: moxart: Avoid forward declaration
gpio: mxs: Allow for recursive enable_irq_wake() call
gpio: samsung: Add missing "break" statement
gpio: twl4030: Remove redundant assignment
gpio: dwapb: correct gpio-cells in binding document
gpio: iop: fix devm_ioremap_resource() return value checking
pinctrl: coh901: convert driver to use gpiolib irqchip
pinctrl: nomadik: convert driver to use gpiolib irqchip
gpio: pl061: convert driver to use gpiolib irqchip
gpio: add IRQ chip helpers in gpiolib
pinctrl: nomadik: factor in platform data container
pinctrl: nomadik: rename secondary to latent
gpio: Driver for SYSCON-based GPIOs
gpio: generic: Use platform_device_id->driver_data field for driver flags
pinctrl: coh901: move irq line locking to resource callbacks
...
functionality this time, just incremental driver updates:
- A large refactoring of the MVEBU (Marvell) driver.
- A large refactoring of the Tegra (nVidia) driver.
- GPIO interrupt including soft edges support in the
STi driver.
- Misc updates to PFC (Renesas), AT91, ADI2 (Blackfin),
pinctrl-single, sirf (CSR), msm (Qualcomm), Exynos (Samsung),
sunxi (AllWinner), i.MX (Freescale), Baytrail.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=i7Sq
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v3.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control bulk changes from Linus Walleij:
"Pin control bulk changes for the v3.15 series, no new core
functionality this time, just incremental driver updates:
- A large refactoring of the MVEBU (Marvell) driver.
- A large refactoring of the Tegra (nVidia) driver.
- GPIO interrupt including soft edges support in the STi driver.
- Misc updates to PFC (Renesas), AT91, ADI2 (Blackfin),
pinctrl-single, sirf (CSR), msm (Qualcomm), Exynos (Samsung), sunxi
(AllWinner), i.MX (Freescale), Baytrail"
* tag 'pinctrl-v3.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (72 commits)
pinctrl: tegra: add some missing Tegra114 entries
pinctrl: tegra: fix some mistakes in Tegra124
pinctrl: msm: fix up out-of-order merge conflict
pinctrl: st: Fix error check for of_irq_to_resource usage
pinctrl: tegra: consistency cleanup
pinctrl: tegra: dynamically calculate function list of groups
pinctrl: tegra: init Tegra20/30 at module_init time
pinctrl: st: Use ARRAY_SIZE instead of raw value for number of delays
pinctrl: st: add pinctrl support for the STiH407 SoC
pinctrl: st: Enhance the controller to manage unavailable registers
pinctrl: msm: Simplify msm_config_reg() and callers
pinctrl: msm: Remove impossible WARN_ON()s
pinctrl: msm: Replace lookup tables with math
pinctrl: msm: Drop OF_IRQ dependency
pinctrl: msm: Drop unused includes
pinctrl: msm: Check for ngpios > MAX_NR_GPIO
pinctrl: msm: Silence recursive lockdep warning
pinctrl: mvebu: silence WARN to dev_warn
pinctrl: msm: drop wake_irqs bitmap
pinctrl-baytrail: add function mux checking in gpio pin request
...
This switches all GPIO and pin control drivers with irqchips
that were using .startup() and .shutdown() callbacks to lock
GPIO lines for IRQ usage over to using the .request_resources()
and .release_resources() callbacks just introduced into the
irqchip vtable.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jean-Jacques Hiblot <jjhiblot@traphandler.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
USP0 has multiple functions, and has RX and TX frame sync signals,
for some scenarios like audio PCM, we don't need both of them.
so here we add two possibilities for USP0 only holding one of TX
and RX frame sync.
commit 8385af02ba only added this group for prima2, and missed
atlas6. This patch fixes it.
Signed-off-by: Rongjun Ying <rongjun.ying@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
according to datasheet and ac97_muxmask assignment, ac97_pins should be
corrected.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This uses the new API for tagging GPIO lines as in use by
IRQs. This enforces a few semantic checks on how the underlying
GPIO line is used.
Also assign the gpio_chip.dev pointer to be used for error
messages.
Cc: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
busses like i2c, spi and so on can parse the virq of their subnode automatically by
irq_of_parse_and_map(). for example, i2c will do that in of_i2c_register_devices().
people can put hwirq number attached to a gpio controller in dts, and drivers can
directly request the parsed virq.
for example, for an i2c client as below,
tangoc-ts@5c{
compatible = "pixcir,tangoc-ts";
interrupt-parent = <&gpio>;
interrupts = <3 0>;
reg = <0x5c>;
};
in i2c client probe(), it will request_irq(client->irq, ...) without
calling gpio_direction_input().
so here when we set irq type, we also put the pin to input direction.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
in sirfsoc gpio probe(), we create 5 irq_domains for 5 gpio banks. but
in irq_create_of_mapping() of irqchip core level, irq_find_host() can
only return the 1st irq_domain attached the pinctrl dt device node as
we can see from the codes:
unsigned int irq_create_of_mapping(struct device_node *controller,
const u32 *intspec, unsigned int intsize)
{
struct irq_domain *domain;
...
domain = controller ? irq_find_host(controller) : irq_default_domain;
}
struct irq_domain *irq_find_host(struct device_node *node)
{
struct irq_domain *h, *found = NULL;
int rc;
/* We might want to match the legacy controller last since
* it might potentially be set to match all interrupts in
* the absence of a device node. This isn't a problem so far
* yet though...
*/
mutex_lock(&irq_domain_mutex);
list_for_each_entry(h, &irq_domain_list, link) {
if (h->ops->match)
rc = h->ops->match(h, node);
else
rc = (h->of_node != NULL) && (h->of_node == node);
if (rc) {
found = h;
break;
}
}
mutex_unlock(&irq_domain_mutex);
return found;
}
for sirfsoc, the 1st irq_domain attached to the device_node(controller) only
can do linear for the 1st 32 gpios. so for devices who use gpio hwirq above
32 and put the information in dt like:
tangoc-ts@5c{
compatible = "pixcir,tangoc-ts";
+ interrupt-parent = <&gpio>;
+ interrupts = <34 0>;
};
we will fail to get the virq for these devices as hwirq will be bigger than
domain->revmap_data.linear.size in:
unsigned int irq_linear_revmap(struct irq_domain *domain,
irq_hw_number_t hwirq)
{
/* Check revmap bounds; complain if exceeded */
if (WARN_ON(hwirq >= domain->revmap_data.linear.size))
return 0;
return domain->revmap_data.linear.revmap[hwirq];
}
this patch drops redundant irq_domain and keep only one to fix the problem.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
USP0 has multiple functions, and has RX and TX frame sync signals,
for some scenarios like audio PCM, we don't need both of them.
so here we add two possibilities for USP0 only holding one of TX
and RX frame sync.
Signed-off-by: Rongjun Ying <Rongjun.Ying@csr.com>
Signed-off-by: Barry Song <Barry.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
sdmmc5 has only 3 pins CMD, CLK, DATA which are connected with CSR
TriG RF multi-GNSS. The hardware connection is like:
DATA -- GPS_SGN
CLK -- GPS_RF_CLK
CMD -- GPS_MAG
here we drop redundant pins in sdmmc5 group.
Signed-off-by: Bin Shi <Bin.Shi@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
commit af614b2301 adds lost USP-based UART pin groups for prima2,
but missed usp1_uart_nostreamctrl group for atlas6, this patch fixes it.
this makes USP(Universal Serial Ports) port1 can work as uart without
stream ctrl.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
dn and dp of USB1 can share with UART1(UART1 can route rx,tx to dn and dp pins of USB1).
here we add this pinmux capability.
USB1/UART1 mode selection has dedicated control register in RSC module, here we attach
the register offset of private data of related pin groups.
Signed-off-by: Rong Wang <Rong.Wang@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
USP(Universal Serial Ports) can be UART as commit 5df831117b,
this patch defines the USP-based UART function pin groups for prima2.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
the old codes defined uart0_nostreamctrl_pins, but missed pingroup
and padmux definition for it. this patch fixes it.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJSGqS5AAoJEHm+PkMAQRiGFxEH/3VrqF6WAkcviNiW/0DCdO8k
v6Wi7Sp5LxVkwzmOCHCV1tTHwLRlH3cB9YmJlGQ0kHCREaAuEQAB0xJXIW7dnyYj
Qq7KoRZEMe3wizmjEsj8qsrhfMLzHjBw67hBz2znwW/4P7YdgzwD7KRiEat+yRC9
ON3nNL2zIqpfk92RXvVrSVl4KMEM+WNbOfiffgBiEP24Ja1MJMFH1d4i6hNOaB0x
9Pb3Lw8let92x+8Ao5jnjKdKMgVsoZWbN/TgQR8zZOHM38AGGiDgk18vMz+L+hpS
jqfjckxj1m30jGq0qZ9ZbMZx3IGif4KccVr30MqNHJpwi6Q24qXvT3YfA3HkstM=
=nAab
-----END PGP SIGNATURE-----
Merge tag 'v3.11-rc7' into devel
Merged in this to avoid conflicts with the big locking fixes
from upstream.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Conflicts:
drivers/pinctrl/pinctrl-sunxi.c
the old codes defined uart0_nostreamctrl_pins, but missed pingroup
and padmux definition for it. this patch fixes it.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
this patch adds hibernation entries so that the sirf platform can
support suspend-to-disk.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Wei Chen
Thomas Gleixner
Jiang Liu
Krzysztof Kozlowski
Masahiro Yamada
Fabio Estevam
Linus Walleij
Colin Ian King
Barry Song
Wolfram Sang
Linus Torvalds
Rongjun Ying
Pramod Gurav
Bin Shi
Fan Wu
Qipan Li
Rong Wang
Jingoo Han