The commit aef7db4bd5 fixed the problem with
recursive locking in fb blanking code if blank is caused by user setting
the /sys/class/graphics/fb*/blank. However this broke the fbcon timeout
blanking.
If you use a driver that defines ->fb_blank operation and at the same time
that driver relies on other driver (e.g. backlight or lcd class) to blank
the screen, when the fbcon times out and tries to blank the fb, it will
call only fb driver blanker and won't notify the other driver. Thus FB
output is disabled, but the screen isn't blanked.
Restore fbcon blanking and at the same time apply the proper fix for the
above problem: if fbcon_blank is called with FBINFO_FLAG_USEREVENT, we are
already called through notification from fb_blank, thus we don't have to
blank the fb again.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The engine on some radeon variants locks up if color expansion is called
for non aligned source data. This patch enables a feature of the core
fbdev to request aligned input pixmaps and uses the HW clipping engine to
clip the output to the requested size
Addresses http://bugzilla.kernel.org/show_bug.cgi?id=11875
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Tested-by: James Cloos <cloos@jhcloos.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The spi master driver must have num_chipselect set to allow the bus to
initialise. Pass this through the platform data.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The spidev_to_sg() call in spi_s3c24xx_gpio.c was using the wrong method
to convert the spi device into the private data for the driver. Fix this
by using spi_master_get_devdata.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix unsafe order in dma mapping operation: always flush data from the
cache *BEFORE* invalidating it, to allow full duplex transfers where the
same buffer may be used for both writes and reads. Tested with mmc-spi.
Signed-off-by: Jan Nikitenko <jan.nikitenko@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
According to the manual the "tdfOnExit" flag must be set on the last byte
we want to send. The PSC controller holds SS low until the flag is set.
However, the flag was set always on the last byte of the FIFO,
independently if it is the last byte of the transfer. This generates
spurious toggling of the SS signals that breaks the protocol of some
peripherals. Fix.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
make use of the new dmi device loading support to automatically load the
applesmc driver based on the dmi_match table.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Cc: Nicolas Boichat <nicolas@boichat.ch>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The netmos_9xx5_combo type assumes that PCI SSID provides always the
correct value for the number of parallel and serial ports, but there are
indeed broken devices with wrong numbers, which may result in Oops.
This patch simply adds the check of the array range.
Reference: Novell bnc#447067
https://bugzilla.novell.com/show_bug.cgi?id=447067
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
commit 50f3beb50a fixed em28xx-alsa
locking schema. However, a backport macro was kept.
This patch removes the macro, since it is not needed for the module
compilation against upstream.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
libata: blacklist Seagate drives which time out FLUSH_CACHE when used with NCQ
[libata] pata_rb532_cf: fix signature of the xfer function
[libata] pata_rb532_cf: fix and rename register definitions
ata_piix: add borked Tecra M4 to broken suspend list
Replaced usb_kill_usb for usb_unlink_usb
(wait until urb to fully stop require USB core to put the calling process to sleep).
Oops:
http://www.kerneloops.org/raw.php?rawid=71799&msgid=
Signed-off-by: Douglas Schilling Landgraf <dougsland@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/mlx4: Fix MTT leakage in resize CQ
IB/ehca: Fix problem with generated flush work completions
IB/ehca: Change misleading error message on memory hotplug
mlx4_core: Save/restore default port IB capability mask
Some recent Seagate harddrives have firmware bug which causes FLUSH
CACHE to timeout under certain circumstances if NCQ is being used.
This can be worked around by disabling NCQ and fixed by updating the
firmware. Implement ATA_HORKAGE_FIRMWARE_UPDATE and blacklist these
devices.
The wiki page has been updated to contain information on this issue.
http://ata.wiki.kernel.org/index.php/Known_issues
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Per definition, this function should return the number of bytes
consumed. As the original parameter "buflen" is being decremented inside
the read/write loop, save it in "retlen" at the beginning.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Acked-by: Sergei Shtyltov <sshtylyov@ru.mvista.com>
Acked-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The original standalone driver uses a custom address for the error
register. Use it in pata_rb532_cf, too.
Rename two register definitions:
- The address offset 0x0800 in fact is the ATA base, not ATA command
address.
- The offset 0x0C00 is not a regular ATA data address, but a buffered one
allowing 4-byte IO.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Tecra M4 sometimes forget what it is and reports bogus data via DMI
which makes the machine evade broken suspend matching and thus fail
suspend/resume. This patch updates piix_broken_suspend() such that it
can match such case. As the borked DMI data is a bit generic,
matching many entries to make the match more specific is necessary.
As the usual DMI matching is limited to four entries, this patch uses
hard coded manual matching.
This is reported by Alexandru Romanescu.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Alexandru Romanescu <a_romanescu@yahoo.co.uk>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
When resizing a CQ, MTTs associated with the old CQE buffer were not
freed. As a result, if any app used resize CQ repeatedly, all MTTs
were eventually exhausted, which led to all memory registration
operations failing until the driver is reloaded.
Once the RESIZE_CQ command returns successfully from FW, FW no longer
accesses the old CQ buffer, so it is safe to deallocate the MTT
entries used by the old CQ buffer.
Finally, if the RESIZE_CQ command fails, the MTTs allocated for the
new CQEs buffer also need to be de-allocated.
This fixes <https://bugs.openfabrics.org/show_bug.cgi?id=1416>.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This fix enables ehca device driver to generate flush work completions
even if the application doesn't request completions for all work
requests. The current implementation of ehca will generate flush work
completions for the wrong work requests if an application uses non
signaled work completions.
Signed-off-by: Stefan Roscher <stefan.roscher@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The error message printed when the eHCA driver prevents memory hotplug
is misleading -- the user might think that hot-removing the lhca,
hotplugging memory, then hot-adding the lhca again will work, but it
actually doesn't.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6:
ieee1394: sbp2: fix race condition in state change
ieee1394: fix list corruption (reported at module removal)
firewire: fw-sbp2: another iPod mini quirk entry
ieee1394: sbp2: another iPod mini quirk entry
stex sets the timeout in its slave configure routine for all devices.
This now needs to update the request queue timeout in block.
Cc: Ed Lin <ed.lin@promise.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
scsi_eh_try_stu() was still using the timeout parameter in the device
which is now not set (i.e. zero filled) meaning that it waited no time
at all for the start unit command to complete (leading the routine to
conclude failure every time). This lead to a 2.6.27 regression:
http://bugzilla.kernel.org/show_bug.cgi?id=12120
Where firewire devices that were non spec compliant wouldn't spin up.
Fix this by using the block queue timeout value instead.
Reported-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
megaraid_sas sets the timeout in its slave configure routine for devices
on special channels. This now needs to update the request queue timeout
in block.
Cc: "Yang, Bo" <Bo.Yang@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
ibmvscsi sets the timeout in its slave configure routine for disk
devices. This now needs to update the request queue timeout in block.
Cc: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
aacraid updates the timeout in its slave configure routine if it is too
small. This now needs to update the request queue timeout in block.
Cc: AACRAID list <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: Apple ALU wireless keyboards are bluetooth devices
HID: remove setup mutex, fix possible deadlock
HID: add USB ID for another dual gameron adapter
HID: unignore mouse on unibody macbooks
HID: fix blacklist entries for greenasia/pantherlord
We alloc a fake tty in usb serial console setup function. we should
init the tty's kref otherwise we will face WARN_ON after following
invoke of tty_port_tty_set --> tty_kref_get.
Signed-off-by: Kevin Hao <kexin.hao@windriver.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When no console is configured tty_open tries to call kref_get on a NULL
pointer, return ENODEV instead.
Signed-off-by: Will Newton <will.newton@gmail.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The zfcp_scsi_queuecommand was not acting according to the standard
when the respective unit was not available. In this case an -EBUSY was
returned, which is not valid in itself, and in addition scsi_done
was called. This combination is not allowed and was leading to a
double finish of the request and therefor double decrement of the
host_busy counter.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Waiting for the ERP to be finished in a task running in the global
kernel work-queue is a bad idea, especially if the ERP needs to run
another job in this work-queue before it can finish. -> deadlock.
This patch removes the necessity to wait for a finished ERP from the
scan task and moves the job scheduling to the end of the ERP.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The check of having a valid pointer was performed before the
processing was secured by the lock. Between those two steps the
pointer can turn invalid. During further processing another value is
used (referenced by the pointer described above) as a function pointer
which is never verified to be valid either, resulting under some
circumstances in an invalid function call. This patch is fixing both
issues.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Prevent a SCSI target scan for a rport which have turned invalid
in the meantime.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Aborting a SCSI cmnd might requrie to send a abort_fsf_cmnd. If the
creation of this fsf_req fails an ERR_PTR is returned where a NULL
value would be expected as an error indicator. This ERR_PTR is
dereferenced as valid fsf_req in succeeding processing leading to
an error.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Running two wka_port_get calls in parallel could issue two open_port
requests, overwriting the port handle. Don't issue an open_port
for the state PORT_OPENING, and only read the data from GOOD
responses.
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Acked-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
For an incoming RSCN it was checked by the ZFCP_STATUS_PORT_DID_DID
define to re-open a remote port or to test the connection. Since this
define was re-used it was also necessary to replace that define with
ZFCP_STATUS_PORT_PHYS_OPEN.
Signed-off-by: Martin Petermann <martin@linux.vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
USB: serial: add more Onda device ids to option driver
USB: usb-storage: unusual_devs entry for Nikon D2H
USB: storage: unusual_devs entry for Mio C520-GPS
USB: fsl_usb2_udc: Report disconnect before unbinding
USB: fsl_qe_udc: Report disconnect before unbinding
USB: fix SB600 USB subsystem hang bug
Revert "USB: improve ehci_watchdog's side effect in CPU power management"
This reverts commit e669dae614, since it
is incomplete, and clashes with fuller patches and the sparc 32/64
unification effort.
Requested-by: David Miller <davem@davemloft.net>
Acked-by: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When the "hpwdt" module is loaded (even if the /dev/watchdog device is not
opened), then kdump does not work. The panic kernel either does not start at
all or crash in various places.
The problem is that hpwdt_pretimeout is registered with register_die_notifier()
with the highest possible priority. Because it returns NOTIFY_STOP, the
crash_nmi_callback which is also registered with register_die_notifier()
is never executed. This causes the shutdown of other CPUs to fail.
Reverting the order is no option: The crash_nmi_callback executes HLT
and so never returns normally. Because of that, it must be executed as
last notifier, which currently is done.
So, that patch returns NOTIFY_OK to keep the crash_nmi_callback executed.
Signed-off-by: Bernhard Walle <bwalle@suse.de>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Thomas Mingarelli <thomas.mingarelli@hp.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
This patch adds an unusual_devs entry for the Nikon D2H camera.
From: Tobias Kunze Briseño <t@fictive.com>,
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1176) adds an unusual_devs entry for the Mio C520 GPS
unit. Other devices also based on the Mitac hardware use the same USB
interface firmware, so the Vendor and Product names are generalized.
This fixes Bugzilla #11583.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Tamas Kerecsen <kerecsen@bigfoot.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Gadgets disable endpoints in their disconnect callbacks, so
we must call disconnect before unbinding. This also fixes
muram memory leak, since we free muram in the qe_ep_disable().
But mainly the patch fixes following badness:
root@b1:~# insmod fsl_qe_udc.ko
fsl_qe_udc: Freescale QE/CPM USB Device Controller driver, 1.0
fsl_qe_udc e01006c0.usb: QE USB controller initialized as device
root@b1:~# insmod g_ether.ko
g_ether gadget: using random self ethernet address
g_ether gadget: using random host ethernet address
usb0: MAC be:2d:3c:fa:be:f0
usb0: HOST MAC 62:b8:6a:df:38:66
g_ether gadget: Ethernet Gadget, version: Memorial Day 2008
g_ether gadget: g_ether ready
fsl_qe_udc e01006c0.usb: fsl_qe_udc bind to driver g_ether
g_ether gadget: high speed config #1: CDC Ethernet (ECM)
root@b1:~# rmmod g_ether.ko
------------[ cut here ]------------
Badness at drivers/usb/gadget/composite.c:871
[...]
NIP [d10c1374] composite_unbind+0x24/0x15c [g_ether]
LR [d10a82f4] usb_gadget_unregister_driver+0x128/0x168 [fsl_qe_udc]
Call Trace:
[cfb93e80] [cfb1f3a0] 0xcfb1f3a0 (unreliable)
[cfb93eb0] [d10a82f4] usb_gadget_unregister_driver+0x128/0x168 [fsl_qe_udc]
[cfb93ed0] [d10c2a3c] usb_composite_unregister+0x3c/0x4c [g_ether]
[cfb93ee0] [c006bde0] sys_delete_module+0x130/0x19c
[cfb93f40] [c00142d8] ret_from_syscall+0x0/0x38
[...]
fsl_qe_udc e01006c0.usb: unregistered gadget driver 'g_ether'
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch is required for all AMD SB600 revisions to avoid USB subsystem hang
symptom. The USB subsystem hang symptom is observed when the system has
multiple USB devices connected to it. In some cases a USB hub may be required
to observe this symptom.
Reported in bugzilla as #11599, the similar patch for SB700 old revision is:
commit b09bc6cbae
Reported-by: raffaele <ralfconn@tele2.it>
Tested-by: Roman Mamedov <roman@rm.pp.ru>
Signed-off-by: Shane Huang <shane.huang@amd.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This reverts commit f0d781d59c.
It was the wrong thing to do, and does not really do what it said
it did.
Cc: Yi Yang <yi.y.yang@intel.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/i915: Fix copy'n'pasteo that broke VT switch if flushing was non-empty.
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
powerpc: Fix system calls on Cell entered with XER.SO=1
powerpc/cell: Fix GDB watchpoints, again
powerpc/mpic: Don't reset affinity for secondary MPIC on boot
powerpc/cell/axon-msi: Retry on missing interrupt
powerpc: Fix boot freeze on machine with empty memory node
powerpc: Fix IRQ assignment for some PCIe devices
powerpc/spufs: Fix spinning in spufs_ps_fault on signal
powerpc/mpc832x_rdb: fix swapped ethernet ids
powerpc: Use generic PHY driver for Marvell 88E1111 PHY on GE Fanuc SBC610
powerpc/85xx: L2 cache size wrong in 8572DS dts
powerpc/virtex: Update defconfigs
powerpc/52xx: update defconfigs
xsysace: Fix driver to use resource_size_t instead of unsigned long
powerpc/virtex: fix various format/casting printk mismatches
powerpc/mpc5200: fix bestcomm Kconfig dependencies
powerpc/44x: Fix 460EX/460GT machine check handling
powerpc/40x: Limit allocable DRAM during early mapping
* master.kernel.org:/home/rmk/linux-2.6-arm:
Allow architectures to override copy_user_highpage()
[ARM] pxa/palmtx: misc fixes to use generic GPIO API
ARM: OMAP: Fixes for suspend / resume GPIO wake-up handling
[ARM] pxa/corgi: update default config to exclude tosa from being built
[ARM] pxa/pcm990: use negative number for an invalid GPIO in camera data
ARM: OMAP: Typo fix for clock_allow_idle
ARM: OMAP: Remove broken LCD driver for SX1
[ARM] 5335/1: pxa25x_udc: Fix is_vbus_present to return 1 or 0
[ARM] pxa/MioA701: bluetooth resume fix
[ARM] pxa/MioA701: fix memory corruption.
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/i915: Save/restore HWS_PGA on suspend/resume
drm: move drm vblank initialization/cleanup to driver load/unload
drm/i915: execbuffer pins objects, no need to ensure they're still in the GTT
drm/i915: Always read pipestat in irq_handler
drm/i915: Subtract total pinned bytes from available aperture size
drm/i915: Avoid BUG_ONs on VT switch with a wedged chipset.
drm/i915: Remove IMR masking during interrupt handler, and restart it if needed.
drm/i915: Manage PIPESTAT to control vblank interrupts instead of IMR.
* 'linux-next' of git://git.infradead.org/~dedekind/ubi-2.6:
UBI: Don't exit from ubi_thread until kthread_should_stop() is true
UBI: fix EBADMSG handling
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
toshiba_acpi: close race in toshiba_acpi driver
ACPICA: disable _BIF warning
ACPI: delete OSI(Linux) DMI dmesg spam
ACPICA: Allow _WAK method to return an Integer
ACPI: thinkpad-acpi: fix fan sleep/resume path
sony-laptop: printk tweak
sony-laptop: brightness regression fix
Revert "ACPI: don't enable control method power button as wakeup device when Fixed Power button is used"
ACPI suspend: Blacklist boxes that require us to set SCI_EN directly on resume
ACPI: scheduling in atomic via acpi_evaluate_integer ()
ACPI: battery: Convert discharge energy rate to current properly
ACPI: EC: count interrupts only if called from interrupt handler.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: wacom - add support for new USB Tablet PCs
Input: replace spin_lock_bh with spin_lock_irqsave in ml_ff_playback
Input: i8042 - add Compal Hel80 laptop to nomux blacklist
Input: cm109 - add keymap for ATCom AU-100 phone
Input: fix the example of an input device driver
Input: psmouse - fix incorrect validate_byte check in OLPC protocol
Input: atkbd - cancel delayed work before freeing its structure
Input: atkbd - add keymap quirk for Inventec Symphony systems
Input: i8042 - add Dell XPS M1530 to nomux list
Input: elo - fix format string in elo driver
ml_ff_playback() uses spin_(un)lock_bh. However this function is called
with interrupts disabled from erase_effect() in drivers/input/ff-core.c:196.
This is not permitted, and will result in a WARN_ON in the bottom half handling code.
This patch changes this function to just use spin_lock_irqsave() instead, solving
the problem and simplifying the locking logic.
This was reported as entry #106559 in kerneloops.org
Reported-by: kerneloops.org
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
... by giving the instances' names magic suffix recognized by modpost ;-/
Their ->probe() is __devinit
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
for fsck sake, it's used only when parsing kernel command line...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
a) hisax_init_pcmcia() needs to be defined only if we have
CONFIG_HOTPLUG (no PCMCIA support otherwise) and can be declared
__devinit.
b) HiSax_inithardware() can go __init
c) hisax_register() is passing to checkcard() full-blown hisax_cs_setup_card():
checkcard(i, id, NULL, hisax_d_if->owner, hisax_cs_setup_card);
The problem with it is that
* hisax_cs_setup_card() is __devinit
* hisax_register() is not
* hisax_cs_setup_card() is a switch from hell, calling a lot of
setup_some_weirdcard() depending on card->typ. _These_ are also
__devinit.
However, in hisax_register() we have card->typ equal to
ISDN_CTYPE_DYNAMIC, which reduces hisax_cs_setup_card() to "nevermind
all that crap, just do nothing and return 2". So we add a
trimmed-down callback doing just that and passed to checkcard() by
hisax_register(). _This_ is non-init (we can stand the impact on
.text size).
Voila - no section warnings from drivers/isdn
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
'aperture' is declared devinitdata (the whole word of it) and
is used from ->fetch_size() which can, AFAICS, be used on
!HOTPLUG after init time.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
functions calling devinit and called only from devinit
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
a) ->probe() can be __devinit; no need to put it into .text
b) calling __init stuff from it, OTOH, is wrong
c) ->remove() is __devexit fodder
Acked-by: rmk+kernel@arm.linux.org.uk
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ibmtr_resume() is calling ibmtr_probe(), which is devinit. Whether
that's the right thing to do there is a separate question, but
since it's PCMCIA and thus will never compile without HOTPLUG...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ixgbe_init_interrupt_scheme() is called from ixgbe_resume(). Build that
with CONFIG_PM and without CONFIG_HOTPLUG and you've got a problem.
Several helpers called by it also are misannotated __devinit.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* rackmeter_remove() reference needs devexit_p
* rackmeter_setup() is calls devinit and is called only from devinit
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
PCI side of driver should be devinit, not init
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
switch to __init for those; unlike powerpc sparc has no hotplug support
for that stuff and their ->probe() tends to call __init functions while
being declared __devinit.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The code
if (shost->dma_channel != NO_ISA_DMA)
free_dma(shost->dma_channel);
in there is triggerable only if we have CONFIG_ISA (we only set ->dma_channel to
something other than NO_ISA_DMA under #ifdef CONFIG_ISA). OTOH, free_dma() is
not guaranteed to be there in absense of CONFIG_ISA. IOW, driver runs into
undefined symbols on PCI-but-not-ISA configs (e.g. on frv) and it's a false
positive.
Fix: put the entire if () under #ifdef CONFIG_ISA; behaviour doesn't change and
dependency on free_dma() disappears for !CONFIG_ISA.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Uses clk_...() a lot
Acked-by: rmk+kernel@arm.linux.org.uk
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
icside_register_v[56] is called from (__devinit) icside_probe
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
talitos_remove() can be called from talitos_probe() on failure
exit path, so it can't be __devexit.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
stli_findeisabrds() and stli_initbrds() are using __init and called only
from __init.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With the introduction of CONFIG_DYNAMIC_PRINTK_DEBUG it is possible to
allow debugging without having to recompile the kernel. This patch turns
all BT_DBG() calls into pr_debug() to support dynamic debug messages.
As a side effect all CONFIG_BT_*_DEBUG statements are now removed and
some broken debug entries have been fixed.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch allows the Asus WL-BTD202 dongle to be used with a mono
headset without having to specify "options btusb force_scofix=1".
Based on a patch from Guillaume Bedot <littletux@zarb.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Bluetooth subsystem was not using the HCI Reset command when doing
device initialization. The Bluetooth 1.0b specification was ambiguous
on how the device firmware was suppose to handle it. Almost every device
was triggering a transport reset at the same time. In case of USB this
ended up in disconnects from the bus.
All modern Bluetooth dongles handle this perfectly fine and a lot of
them actually require that HCI Reset is sent. If not then they are
either stuck in their HID Proxy mode or their internal structures for
inquiry and paging are not correctly setup.
To handle old and new devices smoothly the Bluetooth subsystem contains
a quirk to force the HCI Reset on initialization. However maintaining
such a quirk becomes more and more complicated. This patch turns the
logic around and lets the old devices disable the HCI Reset command.
The only device where the HCI_QUIRK_NO_RESET is still needed are the
original Digianswer devices and dongles with an early CSR firmware.
CSR reported that they fixed this for version 12 firmware. The last
official release of version 11 firmware is build ID 115. The first
version 12 candidate was build ID 117.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The old hci_usb driver has been fully replaced with the new btusb driver
and all major distributions switched to the new driver now. This removes
it since it should not be used at all anymore.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Following the pattern from hci_*.c, turn off BT_DBG messages unless
they have been requested via HCI_UART_DEBUG
Signed-off-by: Nick Pelly <npelly@google.com>
Acked-by: Brian Swetland <swetland@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Since size, addr, fcs, and tmp are unsigned, it would seem better to use
simple_strtoul that simple_strtol.
A simplified version of the semantic patch that makes this change is as
follows: (http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@r2@
long e;
position p;
@@
e = simple_strtol@p(...)
@@
position p != r2.p;
type T;
T e;
@@
e =
- simple_strtol@p
+ simple_strtoul
(...)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch fixes accumulating of the header in case packet was requeued
in the error path.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
During suspend it is important that all URBs are cancelled and then on
resume re-submitted. This gives initial suspend/resume support.
Based on initial work from Oliver Neukum <oneukum@suse.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
With the addition of usb_unlink_anchored_urbs() it is possible to fully
control the bulk URBs from the notify callback. There is no need to
schedule work and so only do this for the ISOC URBs.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The URB submission routines need more fine grained control for the
mem_flags used by kmalloc(), usb_alloc_urb() and usb_submit_urb() to
better support different caller situations. Add a mem_flags parameter
and give the caller full control.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Join the move away from the obsolete info() macro, opencoding the
remaining uses. While we're at it, also get rid of the warn() macro
by promoting the three remaining uses to err().
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
The N_GIGASET_M101 line discipline implemented by the ser_gigaset
driver does not transfer any data from/to userspace through the
tty interface. Therefore a poll method is not needed.
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
One fail path in hrz_probe omitted device disable. Fix it.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An intermediate transition from _RUNNING to _IN_SHUTDOWN could have been
missed by the former code.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
If there is more than one FireWire controller present, dummy_zero_addr
and dummy_max_addr were added multiple times to different lists, thus
corrupting the lists. Fix this by allocating them dynamically per host
instead of just once globally.
(Perhaps a better address space allocation algorithm could rid us of the
two dummy address spaces.)
Fixes http://bugzilla.kernel.org/show_bug.cgi?id=10129 .
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
pppol2tp_sock_to_session() do sock_hold() if the session to release is
not NULL.
Signed-off-by: Frédéric Moulins <frederic.moulins@alsatis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function is_pure_response() does "ntohl(var) & const" and then
essentially just tests whether the result is 0 or not; this can be done
more efficiently by computing "var & htonl(const)" instead and doing the
byte swap at compile time instead of run time.
This change slightly shrinks the compiled code; eg on x86-64 we save a
couple of bswapl instructions:
add/remove: 0/0 grow/shrink: 0/1 up/down: 0/-8 (-8)
function old new delta
t3_sge_intr_msix_napi 544 536 -8
and this also has the pleasant side effect of fixing a sparse warning:
drivers/net/cxgb3/sge.c:2313:15: warning: restricted degrades to integer
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 7ff93f8b ("mlx4_core: Multiple port type support") introduced
support for different port types. As part of that support, SET_PORT
is invoked to set the port type during driver startup. However, as a
side-effect, for IB ports the invocation of this command also sets the
port's capability mask to zero (losing the default value set by FW).
To fix this, get the default ib port capabilities (via a MAD_IFC Port
Info query) during driver startup, and save them for use in the
mlx4_SET_PORT command when setting the port-type to Infiniband.
This patch fixes problems with subnet manager (SM) failover such as
<https://bugs.openfabrics.org/show_bug.cgi?id=1183>, which occurred
because the IsTrapSupported bit in the capability mask was zeroed.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch adds the STMicroelectronics ste10xp PHY device driver.
It supports both the ste100p and the ste101p devices.
Suspend/resume alredy added.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the power management support into the physical
abstraction layer.
Suspend and resume functions respectively turns on/off the bit 11
into the PHY Basic mode control register.
Generic PHY device starts supporting PM.
In order to support the wake-on LAN and avoid to put in power down
the PHY device, the MDIO is aware of what the Ethernet device wants to do.
Voluntary, no CONFIG_PM defines were added into the sources.
Also generic suspend/resume functions are exported to allow
other drivers use them (such as genphy_config_aneg etc.).
Within the phy_driver_register function, we need to remove the
memset. It overrides the device driver owner and it is not good.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the PHY device driver for the National Semiconductor
DP83865 Gig PHYTER.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These warning originate from 50014f1 (ne2: convert to
net_device_ops) which did drop those functions.
drivers/net/ne2.c:140: warning: 'ne_open' declared 'static' but never defined
drivers/net/ne2.c:141: warning: 'ne_close' declared 'static' but never defined
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
the toshiba ACPI driver will, in a failure case, free the rfkill state
before stopping the polling timer that would use this state. More interesting,
in the same failure case handling, it calls the exit function, which also
frees the rfkill state, but after stopping the polling.
If the race happens, a NULL pointer is passed to rfkill_force_state()
which then causes a nice dereference.
Fix the race by just not doing the too-early freeing of the rfkill state.
This appears to be the cause of a hot issue on kerneloops.org; while I
have no solid evidence of that this patch will fix the issue, the race
appears rather real.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
i2c clients should be removed in reverse order compared to the probe
(actually: bind) order. This matters when several clients depend on
each other.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Build fixes for isp1301_omap; no behavior changes:
- fix incorrect probe() signature (it changed many months ago)
- provide missing functions on H3 and H4 boards
- "sparse" fixes (static, NULL-vs-0)
The H3 build bits subset some of the stuff that was previously in
the OMAP tree but never went to mainline.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
While parsing 'hid_blacklist' in the apple alu wireless keyboard is not found.
This happens because in the blacklist it is declared with HID_USB_DEVICE
although the keyboards are really bluetooth devices. The same holds for
'apple_devices' list.
This patch fixes it by changing HID_USB_DEVICE to HID_BLUETOOTH_DEVICE in those
two lists.
Signed-off-by: Jan Scholz <Scholz@fias.uni-frankfurt.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
ixgbe_init_interrupt_scheme() is called from ixgbe_resume(). Build that
with CONFIG_PM and without CONFIG_HOTPLUG and you've got a problem.
Several helpers called by it also are misannotated __devinit.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the calls necessary to enable advanced error reporting for igb on
systems with AER enabled.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The system log messages created on a link status change need to follow a
specific format to work with tools some customers use. This also makes
the messages consistant with other Intel driver link messages.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The system log messages created on a link status change need to follow a
specific format to work with tools some customers use. This also makes
the messages consistant with other Intel driver link messages.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The system log messages created on a link status change need to follow a
specific format to work with tools some customers use. This also makes
the messages consistant with other Intel driver link messages.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The system log messages created on a link status change need to follow a
specific format to work with tools some customers use. This also makes
the messages consistant with other Intel driver link messages.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The system log messages created on a link status change need to follow a
specific format to work with tools some customers use.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linux will continue to ignore OSI(Linux),
except for a white-list containing a few systems.
So delete the black-list,
and stop soliciting user-feedback on the console.
Signed-off-by: Len Brown <len.brown@intel.com>
This fixes a regression from v2.6.27, caused by commit
5814f737e1cd2cfa2893badd62189acae3e1e1fd, "ACPI: thinkpad-acpi:
attempt to preserve fan state on resume".
It is possible for fan_suspend() to fail to properly initialize
fan_control_desired_level as required by fan_resume(), resulting on
the fan always being set to level 7 on resume if the user didn't
touch the fan controller.
In order to get fan sleep/resume handling to work right:
1. Fix the fan_suspend handling of the T43 firmware quirk. If it is
still undefined, we didn't touch the fan yet and that means we have no
business doing it on resume.
2. Store the fan level on its own variable to avoid any possible
issues with hijacking fan_control_desired_level (which isn't supposed
to have anything other than 0-7 in it, anyway).
3. Change the fan_resume code to me more straightforward to understand
(although we DO optimize the boolean logic there, otherwise it looks
disgusting).
4. Add comments to help understand what the code is supposed to be
doing.
5. Change fan_set_level to be less strict about how auto and
full-speed modes are requested.
http://bugzilla.kernel.org/show_bug.cgi?id=11982
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Reported-by: Tino Keitel <tino.keitel@tikei.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Update FW loading path to accomodate in-kernel images location
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add consistency in alloc_ring() parameter checking
to avoid potential memory leaks.
alloc_ring() callers are correct fo far.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix t3_eth_xmit() missing into the netdev_ops structure.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PAUSE frames are only relevant for the real device, broadcasting them
to all macvlan devices can cause a significant load increase.
Reported-by: Ben Greear <greearb@candelatech.com>
Tested-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's no need to print "Sony: " just after "sony-laptop: " (DRV_PFX).
Signed-off-by: Alessandro Guido <ag@alessandroguido.name>
Signed-off-by: Len Brown <len.brown@intel.com>
After commit 540b8bb9c33935183ceb5bed466a42ad72b2af56:
sony-laptop: fingers off backlight if video.ko is serving this functionality
I can't set brightness on my sony laptop (nothing in /sys/class/backlight).
dmesg says "sony-laptop: Sony: Brightness ignored, must be controlled by ACPI
video driver".
The function acpi_video_backlight_support returns 0 if we should use the
vendor-specific backlight support, while non-0 if the ACPI generic should
be used. Because of this, the check introduced by the said commit appears
reversed.
Signed-off-by: Alessandro Guido <ag@alessandroguido.name>
Signed-off-by: Len Brown <len.brown@intel.com>
Some Apple boxes evidently require us to set SCI_EN on resume
directly, because if we don't do that, they hung somewhere in the
resume code path. Moreover, on these boxes it is not sufficient to
use acpi_enable() to turn ACPI on during resume. All of this is
against the ACPI specification which states that (1) the BIOS is
supposed to return from the S3 sleep state with ACPI enabled
(SCI_EN set) and (2) the SCI_EN bit is owned by the hardware and we
are not supposed to change it.
For this reason, blacklist the affected systems so that the SCI_EN
bit is set during resume on them.
[NOTE: Unconditional setting SCI_EN for all system on resume doesn't
work, because it makes some other systems crash (that's to be
expected). Also, it is not entirely clear right now if all of the
Apple boxes require this workaround.]
This patch fixes the recent regression tracked as
http://bugzilla.kernel.org/show_bug.cgi?id=12038
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Tested-by: Tino Keitel <tino.keitel@gmx.de>
Tested-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Now I know why I had strange "scheduling in atomic" problems:
acpi_evaluate_integer() does malloc(..., irqs_disabled() ? GFP_ATOMIC
: GFP_KERNEL)... which is (of course) broken.
There's no way to reliably tell if we need GFP_ATOMIC or not from
code, this one for example fails to detect spinlocks held.
Fortunately, allocation seems small enough to be done on stack.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Acked-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
ACPI battery interface reports its state either in mW or in mA, and
discharge rate in your case is reported in mW. power_supply interface
does not have such a parameter, so current_now parameter is used
for all cases. But in case of mW, reported discharge should
be converted into mA.
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Tested-by: Ferenc Wagner <wferi@niif.hu>
Signed-off-by: Len Brown <len.brown@intel.com>
This patch fixes a regression (introduced by
"p54: more definitions form lmac_longbow.h and pda.h")
It turned out that the "ret" variable wasn't initialized and
this caused the following warnings/errors to appear:
wmaster1: failed to set TX queue parameters for queue 2
wmaster1: failed to set TX queue parameters for queue 3
wmaster1: failed to set TX queue parameters for queue 1
wmaster1: failed to set TX queue parameters for queue 0
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The TX channel width of the BSS can be obtained only after association.
In all cases, default to HT20 if HT is enabled, and set
chan width to HT40 only if the BSS supports it.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make firmware caching on startup optional, and make it default.
When the option is not selected and PM_SLEEP is configured, then
cache firmware in the suspend pm_notifier. This configuration saves
about 64k RAM in normal use, but can lead to a situation where the
driver is configured to use a different firmware.
Signed-off by: David Kilroy <kilroyd@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Retrieval of external firmware has been resolved, and should work with
the standard orinoco resume algorithm.
This fixes an issue where priv->hw_unavailable indicates the card is
ready when firmware has not been loaded.
Signed-off by: David Kilroy <kilroyd@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This refactorring will make it easier to share logic with Symbol
firmware.
Signed-off by: David Kilroy <kilroyd@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We would get an oops on RX on -ENOMEM by passing
NULL to the hardware on ath_rx_buf_link(). The oops
would look something like this:
ath_rx_tasklet+0x515/0x53b
ath9k_tasklet+0x48
tasklet_action
__do_softirq
irq_exit
do_IRQ
RIP: ath_rx_buf_link+0x3a
We correct this by handling the requeue directly on
the ath_rx_tasklet() and trying to allocate an skb
*prior* to sending up the last hardware processed
skb. If we run out of memory this gauranteees we have
skbs to work with while it simply drops new received
frames.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch brings the ath5k eeprom parsing code in sync with the work
done on ath_info by Nick Kossifidis and integrates the missing parts
based on the code of the Atheros Legacy HAL release.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update the rate control only with the tx status of first
AMPDU of an aggregation. This patch fixes frequent drops
in throughput.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This instructs FH to increment the retry count of a packet when
it is brought from the memory to TX-FIFO to save transactions
during aggregation flow.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch configures correctly TX DMA channel. It is not
the same as TX queue.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Acked-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Apply same idiom as in 5000 introduced by
'iwlwifi: define firmware file name once'
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds base band calibration support.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch moves iwl_clear_stations_table into iwl-sta.c
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Patch fixes the ad-hoc mode by
1) Removing redundant clear_stations_table which prevented generation of
beacons.
2) Setting assoc_id to 1. It was never set so preventing tx flow
in iwl3945_tx_skb.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Configure the mac address in add_interface and clear it in
remove_interface so that users can change the mac address
to something other than the one in the eeprom. Also avoid
setting it at attach time so that we won't ack packets
until fully set up.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CHANNEL_CCK flag is set for all 2 Ghz channels, so IS_CHAN_CCK() would
turn out to be true for all channles in that band.
Use IS_CHAN_B() now, which checks the channel mode and not the channel
flags.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Dmitry Baryshkov
Benjamin Herrenschmidt
Ben Dooks
Jan Nikitenko
Julien Boibessot
Stefano Babic
Wolfgang Ocker
Henrik Rydberg
Takashi Iwai
Mauro Carvalho Chehab
Linus Torvalds
Hans Verkuil
Douglas Schilling Landgraf
Tejun Heo
Phil Sutter
Roland Dreier
Jack Morgenstein
Stefan Roscher
Joachim Fenkes
James Bottomley
Kevin Hao
Will Newton
Swen Schillig
Christof Schmitt
Martin Petermann
Bernhard Walle
Greg Kroah-Hartman
Tobias Kunze Briseño
Alan Stern
Anton Vorontsov
Shane Huang
Eric Anholt
Arjan van de Ven
Al Viro
Marcel Holtmann
Nick Pelly
Julia Lawall
Tomas Winkler
Tilman Schmidt
Jiri Slaby
Stefan Richter
Frédéric Moulins
Giuseppe Cavallaro
David S. Miller
Ilpo Järvinen
Jean Delvare
David Brownell
Jan Scholz
Al Viro
Russell King
Alexander Duyck
Jeff Kirsher
Len Brown
Henrique de Moraes Holschuh
Divy Le Ray
Patrick McHardy
Alessandro Guido
Rafael J. Wysocki
Pavel Machek
Alexey Starikovskiy
Alexey Starikovskiy
Ping Cheng
John W. Linville
Christian Lamparter
Sujith
David Kilroy
Luis R. Rodriguez
Felix Fietkau
Vasanthakumar Thiagarajan
Abhijeet Kolekar
Bob Copeland