* 'tty-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6:
serial: bcm63xx_uart: fix irq storm after rx fifo overrun.
amba pl011: platform data for reg lockup and glitch v2
amba pl011: workaround for uart registers lockup
tty: n_gsm: improper skb_pull() use was leaking framed data
tty: n_gsm: Fixed logic to decode break signal from modem status
TTY: ntty, add one more sanity check
TTY: ldisc, do not close until there are readers
8250: Fix capabilities when changing the port type
8250_pci: Fix missing const from merges
ARM: SAMSUNG: serial: Fix on handling of one clock source for UART
serial: ioremap warning fix for jsm driver.
8250_pci: add -ENODEV code for Intel EG20T PCH
The driver went to initialize its waitqueue at the start of the main
processing thread. However, it is possible that this thread is not
scheduled on a CPU before the write function is called which leads to a
following error:
BUG: spinlock bad magic on CPU#1, swapper/1
lock: f5f3ebdc, .magic: 00000000, .owner: <none>/-1, .owner_cpu: 0
Pid: 1, comm: swapper Not tainted 3.0.0-rc2+ #67
Call Trace:
[<c1289663>] spin_bug+0xa3/0xf0
[<c12897ad>] do_raw_spin_lock+0x7d/0x150
[<c14963de>] _raw_spin_lock_irqsave+0x4e/0x60
[<c102f2bb>] __wake_up+0x1b/0x50
[<c12d3715>] serial_m3110_con_write+0x55/0x60
[<c1041575>] __call_console_drivers+0x75/0x90
[<c10415d9>] _call_console_drivers+0x49/0x80
[<c1041baa>] console_unlock+0xca/0x1f0
[<c10420ef>] vprintk+0x18f/0x4f0
[<c14928a3>] printk+0x18/0x1a
[<c1042730>] register_console+0x2e0/0x350
[<c12d098e>] uart_add_one_port+0x33e/0x3d0
[<c1485ba6>] serial_m3110_probe+0x1c2/0x1df
[<c1303db7>] spi_drv_probe+0x17/0x20
...
Fix this by initializing the waitqueue before the main thread is
created.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Change print message to notice instead of error to clean up non critical
messages showing on startup. The MAX3111 not being present is a normal
path for end user systems.
Signed-off-by: William Douglas <william.douglas@intel.com>
[rebased on 3.0, switched to dev_dbg()]
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This workaround aims to break the deadlock situation
which raises during continuous transfer of data for long
duration over uart with hardware flow control. It is
observed that CTS interrupt cannot be cleared in uart
interrupt register (ICR). Hence further transfer over
uart gets blocked.
It is seen that during such deadlock condition ICR
don't get cleared even on multiple write. This leads
pass_counter to decrease and finally reach zero. This
can be taken as trigger point to run this UART_BT_WA.
Workaround backups the register configuration, does soft
reset of UART using BIT-0 of PRCC_K_SOFTRST_SET/CLEAR
registers and restores the registers.
This patch also provides support for uart init and exit
function calls if present.
Signed-off-by: Shreshtha Kumar Sahu <shreshthakumar.sahu@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
gsm_dlci_data_output_framed() was doing:
memcpy(dp, skb_pull(dlci->skb, len), len);
The problem is skb_pull() returns the post-increment data ptr
so the first chunk of dlci->skb->data is leaked.
Signed-off-by: Russ Gorby <russ.gorby@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The modem status can be one or 2 octets and contains the V.24 signals
and in the 2 octet case also the break signal.
We were improperly decoding the break signal from the modem in the
2 octet case.
Signed-off-by: Russ Gorby <russ.gorby@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If dmi_get_system_info() returns NULL, pch_uart_init_port() will
dereferencea a zero pointer.
This oops was observed on an Atom based board which has no BIOS, but
a bootloder which doesn't provide DMI data.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Cc: Greg KH <gregkh@suse.de>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The flush_to_ldisc() work entry has special logic to notice when it has
seen the original tail of the data queue, and it avoids continuing the
flush if it sees that _original_ tail rather than the current tail.
This logic can trigger in case somebody is constantly adding new data to
the tty while the flushing is active - and the intent is to avoid
excessive CPU usage while flushing the tty, especially as we used to do
this from a softirq context which made it non-preemptible.
However, since we no longer re-arm the work-queue from within itself
(because that causes other trouble: see commit a5660b41af "tty: fix
endless work loop when the buffer fills up"), this just leads to
possible hung tty's (most easily seen in SMP and with a test-program
that floods a pty with data - nobody seems to have reported this for any
real-life situation yet).
And since the workqueue isn't done from timers and softirq's any more,
it's doubtful whether the CPU useage issue is really relevant any more.
So just remove the logic entirely, and see if anybody ever notices.
Alternatively, we might want to re-introduce the "re-arm the work" for
just this case, but then we'd have to re-introduce the delayed work
model or some explicit timer, which really doesn't seem worth it for
this.
Reported-and-tested-by: Guillaume Chazarain <guichaz@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With the previous patch, we fixed another bug where read_buf was freed
while we still was in n_tty_read. We currently check whether read_buf
is NULL at the start of the function. Add one more check after we wake
up from waiting for input.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We restored tty_ldisc_wait_idle in 100eeae2c5 (TTY: restore
tty_ldisc_wait_idle). We used it in the ldisc changing path to fix the
case where there are tasks in n_tty_read waiting for data and somebody
tries to change ldisc.
Similar to the case above, there may be also tasks waiting in
n_tty_read while hangup is performed. As 65b770468e (tty-ldisc: turn
ldisc user count into a proper refcount) removed the wait-until-idle
from all paths, hangup path won't wait for them to disappear either
now. So add it back even to the hangup path.
There is a difference, we need uninterruptible sleep as there is
obviously HUP signal pending. So tty_ldisc_wait_idle now sleeps
without possibility to be interrupted. This is what original
tty_ldisc_wait_idle did. After the wait idle reintroduction
(100eeae2c5), we have had interruptible sleeps for the ldisc changing
path. But as there is a 5s timeout anyway, we don't allow it to be
interrupted from now on. It's not worth the added complexity of
deciding what kind of sleep we want.
Before 65b770468e tty_ldisc_release was called also from
tty_ldisc_release. It is called from tty_release, so I don't think we
need to restore that one.
This is nicely reproducible after constifying the timing when
drivers/tty/n_tty.c is patched as follows ("TTY: ntty, add one more
sanity check" patch is needed to actually see it explode):
%% -1548,6 +1549,7 @@ static int n_tty_open(struct tty_struct *tty)
/* These are ugly. Currently a malloc failure here can panic */
if (!tty->read_buf) {
+ msleep(100);
tty->read_buf = kzalloc(N_TTY_BUF_SIZE, GFP_KERNEL);
if (!tty->read_buf)
return -ENOMEM;
%% -1785,6 +1788,7 @@ do_it_again:
break;
}
timeout = schedule_timeout(timeout);
+ msleep(20);
continue;
}
__set_current_state(TASK_RUNNING);
===== With a process: =====
while (1) {
int fd = open(argv[1], O_RDWR);
read(fd, buf, sizeof(buf));
close(fd);
}
===== and its child: =====
setsid();
while (1) {
int fd = open(tty, O_RDWR|O_NOCTTY);
ioctl(fd, TIOCSCTTY, 1);
vhangup();
close(fd);
usleep(100 * (10 + random() % 1000));
}
===== EOF =====
References: https://bugzilla.novell.com/show_bug.cgi?id=693374
References: https://bugzilla.novell.com/show_bug.cgi?id=694509
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: stable <stable@kernel.org> [32, 33, 34, 39]
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When changing the port type, the capabilities flags should be changed
also, otherwise the capabilities will not correspond to the port type,
which make set_sleep() crash on rmmod.
This patch just assign the correct capabilites when the port changes.
Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
CC: Michael Reed <mreed@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes the way of comparison for handling of two or more
clock sources for UART.
For example, if just only one clock source is defined even though
there are two clock sources for UART, the serial driver does not
set proper clock up. Of course, it is problem.
So this patch changes the condition of comparison to avoid useless
setup clock and adds a flag 'NO_NEED_CHECK_CLKSRC' which means
selection of source clock is not required.
In addition, since the Exynos4210 has only one clock source for UART
this patch adds the flag into its common_init_uarts().
Signed-off-by: Boojin Kim <boojin.kim@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I saw a warning about ioremap from the jsm driver on a system which
looked like this:
resource map sanity check conflict: 0xe0200800 0xe02017ff 0xe0200800 0xe0200fff 0000:01:08.0
Turns out the warning is valid. The jsm driver has been asking to ioremap
0x1000 forever, but in fact only 8 port chips have 0x1000 bytes of memory.
4 port chips have 0x800 and 2 port chips have 0x400 according to the
data sheet. It makes more sense to map the size of the region rather
than a hard coded value. If you happen to have the region legitimately
mapped to a base address that is not 4K aligned, ioremap complains
otherwise.
Signed-off-by: Len Sorensen <lsorense@csclub.uwaterloo.ca>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This reverts commit b1c43f82c5.
It was broken in so many ways, and results in random odd pty issues.
It re-introduced the buggy schedule_work() in flush_to_ldisc() that can
cause endless work-loops (see commit a5660b41af6a: "tty: fix endless
work loop when the buffer fills up").
It also used an "unsigned int" return value fo the ->receive_buf()
function, but then made multiple functions return a negative error code,
and didn't actually check for the error in the caller.
And it didn't actually work at all. BenH bisected down odd tty behavior
to it:
"It looks like the patch is causing some major malfunctions of the X
server for me, possibly related to PTYs. For example, cat'ing a
large file in a gnome terminal hangs the kernel for -minutes- in a
loop of what looks like flush_to_ldisc/workqueue code, (some ftrace
data in the quoted bits further down).
...
Some more data: It -looks- like what happens is that the
flush_to_ldisc work queue entry constantly re-queues itself (because
the PTY is full ?) and the workqueue thread will basically loop
forver calling it without ever scheduling, thus starving the consumer
process that could have emptied the PTY."
which is pretty much exactly the problem we fixed in a5660b41af.
Milton Miller pointed out the 'unsigned int' issue.
Reported-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reported-by: Milton Miller <miltonm@bga.com>
Cc: Stefan Bigler <stefan.bigler@keymile.com>
Cc: Toby Gray <toby.gray@realvnc.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Intel EG20T PCH has UART device which is compatible with 8250.
Currently, with general configuration, the PCH UART driver is not loaded
but 8250 standard driver is loaded. Therefore, in case of using PCH
UART driver, need to disable 8250 pci function. However, this procedure
is not best solution. This patch, in 8250_pci, if the device is the PCH
or the family IOH, '-ENODEV' is returned. As a result, disabling
8250-pci processing becomes unnecessary.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (45 commits)
ARM: 6945/1: Add unwinding support for division functions
ARM: kill pmd_off()
ARM: 6944/1: mm: allow ASID 0 to be allocated to tasks
ARM: 6943/1: mm: use TTBR1 instead of reserved context ID
ARM: 6942/1: mm: make TTBR1 always point to swapper_pg_dir on ARMv6/7
ARM: 6941/1: cache: ensure MVA is cacheline aligned in flush_kern_dcache_area
ARM: add sendmmsg syscall
ARM: 6863/1: allow hotplug on msm
ARM: 6832/1: mmci: support for ST-Ericsson db8500v2
ARM: 6830/1: mach-ux500: force PrimeCell revisions
ARM: 6829/1: amba: make hardcoded periphid override hardware
ARM: 6828/1: mach-ux500: delete SSP PrimeCell ID
ARM: 6827/1: mach-netx: delete hardcoded periphid
ARM: 6940/1: fiq: Briefly document driver responsibilities for suspend/resume
ARM: 6938/1: fiq: Refactor {get,set}_fiq_regs() for Thumb-2
ARM: 6914/1: sparsemem: fix highmem detection when using SPARSEMEM
ARM: 6913/1: sparsemem: allow pfn_valid to be overridden when using SPARSEMEM
at91: drop at572d940hf support
at91rm9200: introduce at91rm9200_set_type to specficy cpu package
at91: drop boot_params and PLAT_PHYS_OFFSET
...
* 'trivial' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild-2.6:
gfs2: Drop __TIME__ usage
isdn/diva: Drop __TIME__ usage
atm: Drop __TIME__ usage
dlm: Drop __TIME__ usage
wan/pc300: Drop __TIME__ usage
parport: Drop __TIME__ usage
hdlcdrv: Drop __TIME__ usage
baycom: Drop __TIME__ usage
pmcraid: Drop __DATE__ usage
edac: Drop __DATE__ usage
rio: Drop __DATE__ usage
scsi/wd33c93: Drop __TIME__ usage
scsi/in2000: Drop __TIME__ usage
aacraid: Drop __TIME__ usage
media/cx231xx: Drop __TIME__ usage
media/radio-maxiradio: Drop __TIME__ usage
nozomi: Drop __TIME__ usage
cyclades: Drop __TIME__ usage
alpha allmodconfig:
drivers/tty/serial/pch_uart.c: In function 'dma_handle_tx':
drivers/tty/serial/pch_uart.c:873: error: implicit declaration of function 'kzalloc'
drivers/tty/serial/pch_uart.c:873: warning: assignment makes pointer from integer without a cast
drivers/tty/serial/pch_uart.c: In function 'pch_uart_init_port':
drivers/tty/serial/pch_uart.c:1403: warning: assignment makes pointer from integer without a cast
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Architectures that implement their own show_mem() function did not pass
the filter argument to show_free_areas() to appropriately avoid emitting
the state of nodes that are disallowed in the current context. This patch
now passes the filter argument to show_free_areas() so those nodes are now
avoided.
This patch also removes the show_free_areas() wrapper around
__show_free_areas() and converts existing callers to pass an empty filter.
ia64 emits additional information for each node, so skip_free_areas_zone()
must be made global to filter disallowed nodes and it is converted to use
a nid argument rather than a zone for this use case.
Signed-off-by: David Rientjes <rientjes@google.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Helge Deller <deller@gmx.de>
Cc: James Bottomley <jejb@parisc-linux.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
specify the port num via platform_data this will allow to match the clock
with the plaform_dev staticaly
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Patrice Vilchez <patrice.vilchez@atmel.com>
Cc: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/brodo/pcmcia-2.6:
pcmcia: Make struct pcmcia_device_id const, sound drivers edition
staging: pcmcia: Convert pcmcia_device_id declarations to const
pcmcia: Convert pcmcia_device_id declarations to const
pcmcia: Make declaration and uses of struct pcmcia_device_id const
pcmcia/sa1100: put sa11x0_pcmcia_hw_init[] to .devinit.data
* 'sh-latest' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (23 commits)
sh: Ignore R_SH_NONE module relocations.
SH: SE7751: Fix pcibios_map_platform_irq prototype.
sh: remove warning and warning_symbol from struct stacktrace_ops
sh: wire up sys_sendmmsg.
clocksource: sh_tmu: Runtime PM support
clocksource: sh_tmu: __clocksource_updatefreq_hz() update
clocksource: sh_cmt: Runtime PM support
clocksource: sh_cmt: __clocksource_updatefreq_hz() update
dmaengine: shdma: synchronize RCU before freeing, simplify spinlock
dmaengine: shdma: add runtime- and system-level power management
dmaengine: shdma: fix locking
sh: sh-sci: sh7377 and sh73a0 build fixes
sh: cosmetic improvement: use an existing pointer
serial: sh-sci: suspend/resume wakeup support V2
serial: sh-sci: Runtime PM support
sh: select IRQ_FORCED_THREADING.
sh: intc: Set virtual IRQs as nothread.
sh: fixup fpu.o compile order
i2c: add a module alias to the sh-mobile driver
ALSA: add a module alias to the FSI driver
...
* 'tty-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6: (48 commits)
serial: 8250_pci: add support for Cronyx Omega PCI multiserial board.
tty/serial: Fix break handling for PORT_TEGRA
tty/serial: Add explicit PORT_TEGRA type
n_tracerouter and n_tracesink ldisc additions.
Intel PTI implementaiton of MIPI 1149.7.
Kernel documentation for the PTI feature.
export kernel call get_task_comm().
tty: Remove to support serial for S5P6442
pch_phub: Support new device ML7223
8250_pci: Add support for the Digi/IBM PCIe 2-port Adapter
ASoC: Update cx20442 for TTY API change
pch_uart: Support new device ML7223 IOH
parport: Use request_muxed_region for IT87 probe and lock
tty/serial: add support for Xilinx PS UART
n_gsm: Use print_hex_dump_bytes
drivers/tty/moxa.c: Put correct tty value
TTY: tty_io, annotate locking functions
TTY: serial_core, remove superfluous set_task_state
TTY: serial_core, remove invalid test
Char: moxa, fix locking in moxa_write
...
Fix up trivial conflicts in drivers/bluetooth/hci_ldisc.c and
drivers/tty/serial/Makefile.
I did the hci_ldisc thing as an evil merge, cleaning things up.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (39 commits)
b43: fix comment typo reqest -> request
Haavard Skinnemoen has left Atmel
cris: typo in mach-fs Makefile
Kconfig: fix copy/paste-ism for dell-wmi-aio driver
doc: timers-howto: fix a typo ("unsgined")
perf: Only include annotate.h once in tools/perf/util/ui/browsers/annotate.c
md, raid5: Fix spelling error in comment ('Ofcourse' --> 'Of course').
treewide: fix a few typos in comments
regulator: change debug statement be consistent with the style of the rest
Revert "arm: mach-u300/gpio: Fix mem_region resource size miscalculations"
audit: acquire creds selectively to reduce atomic op overhead
rtlwifi: don't touch with treewide double semicolon removal
treewide: cleanup continuations and remove logging message whitespace
ath9k_hw: don't touch with treewide double semicolon removal
include/linux/leds-regulator.h: fix syntax in example code
tty: fix typo in descripton of tty_termios_encode_baud_rate
xtensa: remove obsolete BKL kernel option from defconfig
m68k: fix comment typo 'occcured'
arch:Kconfig.locks Remove unused config option.
treewide: remove extra semicolons
...
This patch adds wakeup support to the sh-sci driver. The serial
core deals with all details but defaults to wakeup disabled. So
to make use of this feature enable wakeup in sysfs:
echo enabled > /sys/class/tty/ttySC0/power/wakeup
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds support for the Omega-PCI, an 8-port asynchronous
multiport adapter for computers with PCI bus [1].
[1] http://www.cronyx.ru/hardware/ompci.html
Signed-off-by: Antony Pavlov <antony@niisi.msk.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When a break is received, Tegra's UART apparently fills the FIFO with
0 bytes. These must be drained so that they aren't interpreted as actual
data received. This allows e.g. MAGIC_SYSRQ to work on Tegra's UARTs.
v2: Added FIXME comment to clear_rx_fifo
Originally-by: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Tegra's UART is currently auto-detected as PORT_XSCALE due to register
bit UART_IER.UUE being writable. However, the Tegra documentation states
that this register bit is reserved. Hence, we should not program it.
Instead, the documentation specifies that the UART is 16550 compatible.
However, Tegra does need register bit UART_IER.RTOIE set, which is not
enabled by any 16550 port type. This was not noticed before, since
PORT_XSCALE enables CAP_UUE, which conflates both UUE and RTOIE bit
programming.
This change defines PORT_TEGRA that doesn't set UART_CAP_UUE, but does
set UART_CAP_RTOIE, which is a new capability indicating that the RTOIE
bit needs to be enabled.
Based-on-code-by: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit b826291c, "drivercore/dt: add a match table pointer to struct
device" added an of_match pointer to struct device to cache the
of_match_table entry discovered at driver match time. This was unsafe
because matching is not an atomic operation with probing a driver. If
two or more drivers are attempted to be matched to a driver at the
same time, then the cached matching entry pointer could get
overwritten.
This patch reverts the of_match cache pointer and reworks all users to
call of_match_device() directly instead.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The n_tracerouter and n_tracesink line discpline drivers use the
Linux tty line discpline framework to route trace data coming
from a tty port (say UART for example) to the trace sink line
discipline driver and to another tty port(say USB). Those
these two line discipline drivers can be used together,
independently from pti.c, they are part of the original
implementation solution of the MIPI P1149.7, compact JTAG, PTI
solution for Intel mobile platforms starting with the
Medfield platform.
Signed-off-by: J Freyensee <james_p_freyensee@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
According to removing ARCH_S5P6442, we don't need to support
serial for S5P6442.
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add support to the 8250 PCI serial driver for the Digi/IBM PCIe 2-port Async EIA-232 Adapter.
Oxford Semiconductor produces a 2/4/8 port UART (OXPCIe952/OXPCIe954/OXPCIe958) chip
called the Tornado, that can be used to create a very simple serial board product.
The kernel sources currently have just 2 vendors using this chip, which is Oxford and Mainpipe.
This new Digi/IBM serial product now uses it as well.
Rather than create a long running comment of vendors using the chip, the one changed comment
in the patch below now just lists "For Oxford Semiconductor Tornado based devices" to be a
more generic comment for all vendors that end up using the Oxford Tornado chip.
Cc: Michael Reed <mreed10@us.ibm.com>
Signed-off-by: Scott Kilau <scottk@digi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Support new device OKI SEMICONDUCTOR ML7223 IOH(Input/Output Hub).
The ML7223 IOH is for MP(Media Phone) use.
The ML7223 is companion chip for Intel Atom E6xx series.
The ML7223 is completely compatible for Intel EG20T PCH.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Saves about 50KB of data.
Old/new size of all objects:
text data bss dec hex filename
563015 80096 130684 773795 bcea3 (TOTALS)
610916 32256 130632 773804 bceac (TOTALS)
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Kurt Van Dijck <kurt.van.dijck@eia.be> (for drivers/net/can/softing/softing_cs.c)
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
The Xilinx PS Uart is used on the new ARM based SoC. This
UART is not compatible with others such that a seperate
driver is required.
Signed-off-by: John Linn <john.linn@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use the standard mechanism to print a hex buffer
to eliminate empty printf warning.
A couple % smaller text and data too.
$ size drivers/tty/n_gsm.o*
text data bss dec hex filename
23543 312 6376 30231 7617 drivers/tty/n_gsm.o.new
24051 408 6496 30955 78eb drivers/tty/n_gsm.o.old
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The tty value that should be put is the one that was just gotten by
tty_port_tty_get, not the one that is the argument to the enclosing
function.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@exists@
local idexpression struct tty_struct *x;
expression ra,rr;
statement S1,S2;
@@
x = tty_port_tty_get(...)
... when != x = rr
when any
when != tty_kref_put(x,...)
when != if (...) { ... tty_kref_put(x,...) ...}
(
if(<+...x...+>) S1 else S2
|
if(...) { ... when != x = ra
when forall
when != tty_kref_put(x,...)
*return...;
}
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Using C line continuation inside format strings is error prone.
Clean up the unintended whitespace introduced by misuse of \.
Neaten correctly used line continations as well for consistency.
drivers/scsi/arcmsr/arcmsr_hba.c has these errors as well,
but arcmsr needs a lot more work and the driver should likely be
moved to staging instead.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
tty_write_lock and tty_write_unlock contain imbalanced locking. But
this is intentional, so mark them appropriately by
__acquires/__releases.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Linus Torvalds
Andrew Morton
Mika Westerberg
William Douglas
Maxime Bizon
Shreshtha Kumar Sahu
Russ Gorby
Alexander Stein
Jiri Slaby
leitao@linux.vnet.ibm.com
Alan Cox
Boojin Kim
Lennart Sorensen
Greg Kroah-Hartman
Tomoya MORINAGA
Russell King
KOSAKI Motohiro
David Rientjes
Jean-Christophe PLAGNIOL-VILLARD
Magnus Damm
Antony Pavlov
Stephen Warren
John Crispin
Grant Likely
J Freyensee
Kukjin Kim
Scott Kilau
Justin P. Mattock
Joe Perches
John Linn
Julia Lawall
Jiri Kosina