port->flags is of type upf_t, which corresponds to UPF_* flags.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This will make it easier to get the driver to support device tree. The
old platform data method is still supported though.
Also change the driver to use only one platform device per port.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is not even used in nios2 arch code anymore.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The three identical uart ports can work either in DMA or PIO mode. Adding such
a module parameter "hsu_dma_enable" will enable user to chose working modes for
each port. If the mfd driver is built in kernel, adding a "mfd.hsu_dma_enable=x"
in kernel command line has the same effect.
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In A0 stepping, TX half-empty interrupt is not working, so have to
use the full-empty interrupts whose performance will be 15% lower.
Now re-enable the half-empty interrrupt after it is enabled in
silicon.
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Kconfig options for the drivers/tty/ files still were hanging around
in the "big" drivers/char/Kconfig file, so move them to the proper
location under drivers/tty and drivers/tty/hvc/
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch changes dependency of ARCH_EXYNOS4 from ARCH_S5PV310
according to the change of ARCH name, EXYNOS4.
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
* 'fixes-2.6.38' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
workqueue: make sure MAYDAY_INITIAL_TIMEOUT is at least 2 jiffies long
workqueue, freezer: unify spelling of 'freeze' + 'able' to 'freezable'
workqueue: wake up a worker when a rescuer is leaving a gcwq
This is useful for system management software so that it can kick
off things like gettys and everything that's started from a tty,
before we reuse it from/for something else or shut it down.
Without this ioctl it would have to temporarily become the owner of
the tty, then call vhangup() and then give it up again.
Cc: Lennart Poettering <lennart@poettering.net>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This basically encapsulates the small bit of locking knowledge needed. While
we are at it make sure we blow up on any more abusers and unsafe misuses of
ioctl for this kind of stuff.
We change the function to return an argument as at some point it needs to
honour the POSIX 'I asked for changes but got none of them' error reporting
corner case.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Only oddities here are a couple of drivers that bogusly called the ldisc
helpers instead of returning -ENOIOCTLCMD. Fix the bug and the rest goes
away.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Doing tiocmget was such fun we should do tiocmset as well for the same
reasons
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We don't actually need this and it causes problems for internal use of
this functionality. Currently there is a single use of the FILE * pointer.
That is the serial core which uses it to check tty_hung_up_p. However if
that is true then IO_ERROR is also already set so the check may be removed.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use the regshift member of struct uart_port to store the address stride
from platform data. This way we can save one dereference per call of
altera_uart_readl and altera_uart_writel.
This also allows us to use the driver without platform data, which is
needed for device tree support in the Nios2 port.
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit 6b5756f176 introduced the
possibility for pdev->id being -1 but the change was not done equally in
altera_uart_remove. This patch fixes this.
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
using VT_SETACTIVATE ioctl for console switch did not work,
since it put wrong param to the set_console function.
Also ioctl returned misleading error, because of the missing
break statement. I wonder anyone has ever used this one :).
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Enables PPS support in atmel serial driver to make PPS API working.
Signed-off-by: Viktar Palstsiuk <viktar.palstsiuk@promwad.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In 8250.c original ns16550 autoconfig code, we change the divisor latch when
we goto to high speed mode, we're assuming the previous speed is legacy. This
some times is not true.
For example in a system with both CONFIG_SERIAL_8250 and
CONFIG_SERIAL_8250_PNP set, in this case, the code (autoconfig) will be called
twice, one in serial8250_init/probe() and the other is from
serial_pnp_probe. When serial_pnp_probe calls the autoconfig for NS16550A,
it's already in high speed mode, change the divisor latch (quot << 3) in this
case will make the UART console garbled.
CC: Greg Kroah-Hartman <greg@kroah.com>
CC: David Woodhouse <dwmw2@infradead.org>
CC: linux-kernel@vger.kernel.org
CC: stable@kernel.org
Signed-off-by: Yin Kangkai <kangkai.yin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
For any reason if the NS16550A was not work in high speed mode (e.g. we hold
NS16550A from going to high speed mode in autoconfig_16550a()), now we are
resume from suspend, we should also set the uartclk to the correct
value. Otherwise it is still the old 1843200 and that will bring issues.
CC: Greg Kroah-Hartman <greg@kroah.com>
CC: David Woodhouse <dwmw2@infradead.org>
CC: linux-kernel@vger.kernel.org
CC: stable@kernel.org
Signed-off-by: Yin Kangkai <kangkai.yin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
renamed spi_driver variable to not be h/w specific
set driver name to use DRVNAME define
removed commented-out define
Signed-off-by: Russ Gorby <russ.gorby@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The probe routine should call spi_setup() to configure
the SPI bus so it can properly communicate with the device.
E.g. the device operates in SPI mode 1.
Called spi_setup to configure SPI mode, max_speed_hz, and bpw
Signed-off-by: Russ Gorby <russ.gorby@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Platforms containing the 6260 can run up to 25Mhz.
For these platforms set max_speed_hz to 25Mhz.
Signed-off-by: Russ Gorby <russ.gorby@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
driver should support 32bit SPI transfers. The boolean variable
only allowed 8/16.
Changed to support 8/16/32 for future enabling
of 32 bpw.
Signed-off-by: Russ Gorby <russ.gorby@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This driver is a SPI protocol driver and has no DMA ops
associated with the device so the call will fail. Furthermore,
the DMA allocation made here will be used by the SPI
controller driver (parent dev) so it makes sense to
pass that device instead.
Signed-off-by: Russ Gorby <russ.gorby@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The port ops must be set AFTER calling port init as that function
zeroes the structure
Signed-off-by: Russ Gorby <russ.gorby@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
seems there's no longer need for using con_buf/conf_buf_mtx
as vcs_read/vcs_write buffer for user's data.
The do_con_write function, that was the other user of this,
is currently using its own kmalloc-ed buffer.
Not sure when this got changed, as I was able to find this code
in 2.6.9, but it's already gone as far as current git history
goes - 2.6.12-rc2.
AFAICS there's a behaviour change with the current change.
The lseek is not completely mutually exclusive with the
vcs_read/vcs_write - the file->f_pos might get updated
via lseek callback during the vcs_read/vcs_write processing.
I tried to find out if the prefered behaviour is to keep
this in sync within read/write/lseek functions, but I did
not find any pattern on different places.
I guess if user end up calling write/lseek from different
threads she should know what she's doing. If needed we
could use dedicated fd mutex/buffer.
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
printk()s without a priority level default to KERN_WARNING. To reduce
noise at KERN_WARNING, this patch set the priority level appriopriately
for unleveled printks()s. This should be useful to folks that look at
dmesg warnings closely.
Signed-off-by: Mandeep Singh Baines <msb@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This converts the existing bfin_jtag_comm TTY driver to the HVC layer so
that the common HVC code can worry about all of the TTY/polling crap and
leave the Blackfin code to worry about the Blackfin bits.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
virtual console: add keyboard mode OFF
Add a new mode for the virtual console keyboard OFF in which all input
other than shift keys is ignored. Prevents vt input buffers from
overflowing when a program opens but doesn't read from a tty, like X11
using evdev for input.
Signed-off-by: Arthur Taylor <art@ified.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Only include linux/pci.h once in drivers/tty/serial/pch_uart.c
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
There are two spellings in use for 'freeze' + 'able' - 'freezable' and
'freezeable'. The former is the more prominent one. The latter is
mostly used by workqueue and in a few other odd places. Unify the
spelling to 'freezable'.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Alex Dubov <oakad@yahoo.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Steven Whitehouse <swhiteho@redhat.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
m68knommu: set flow handler for secondary interrupt controller of 5249
m68knommu: remove use of IRQ_FLG_LOCK from 68360 platform support
m68knommu: fix dereference of port.tty
m68knommu: add missing linker __modver section
m68knommu: fix mis-named variable int set_irq_chip loop
m68knommu: add optimize memmove() function
m68k: remove arch specific non-optimized memcmp()
m68knommu: fix use of un-defined _TIF_WORK_MASK
m68knommu: Rename m548x_wdt.c to m54xx_wdt.c
m68knommu: fix m548x_wdt.c compilation after headers renaming
m68knommu: Remove dependencies on nonexistent M68KNOMMU
The struct_tty associated with a port is now a direct pointer
from within the local private driver info struct. So fix all uses
of it.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Do not include linux/device.h twice in drivers/tty/serial/mxs-auart.c .
Once is enough.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The inline assembly differences for v6 vs. v7 in the hvc_dcc
driver are purely optimizations. On a v7 processor, an mrc with
the pc sets the condition codes to the 28-31 bits of the register
being read. It just so happens that the TX/RX full bits the DCC
driver is testing for are high enough in the register to be put
into the condition codes. On a v6 processor, this "feature" isn't
implemented and thus we have to do the usual read, mask, test
operations to check for TX/RX full.
Since we already test the RX/TX full bits before calling
__dcc_getchar() and __dcc_putchar() we don't actually need to do
anything special for v7 over v6. The only difference is in
hvc_dcc_get_chars(). We would test RX full, poll RX full, and
then read a character from the buffer, whereas now we will test
RX full, read a character from the buffer, and then test RX full
again for the second iteration of the loop. It doesn't seem
possible for the buffer to go from full to empty between testing
the RX full and reading a character. Therefore, replace the v7
versions with the v6 versions and everything works the same.
Acked-by: Tony Lindgren <tony@atomide.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Cc: Daniel Walker <dwalker@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Casting and anding with 0xff is unnecessary in
hvc_dcc_put_chars() since buf is already a char[].
__dcc_get_char() can't return an int less than 0 since it only
returns a char. Simplify the if statement in hvc_dcc_get_chars()
to take this into account.
Cc: Daniel Walker <dwalker@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Without marking the asm __dcc_getstatus() volatile my compiler
decides it can cache the value of __ret in a register and then
check the value of it continually in hvc_dcc_put_chars() (I had
to replace get_wait/put_wait with 1 and fixup the branch
otherwise my disassembler barfed on __dcc_(get|put)char).
00000000 <hvc_dcc_put_chars>:
0: ee103e11 mrc 14, 0, r3, cr0, cr1, {0}
4: e3a0c000 mov ip, #0 ; 0x0
8: e2033202 and r3, r3, #536870912 ; 0x20000000
c: ea000006 b 2c <hvc_dcc_put_chars+0x2c>
10: e3530000 cmp r3, #0 ; 0x0
14: 1afffffd bne 10 <hvc_dcc_put_chars+0x10>
18: e7d1000c ldrb r0, [r1, ip]
1c: ee10fe11 mrc 14, 0, pc, cr0, cr1, {0}
20: 2afffffd bcs 1c <hvc_dcc_put_chars+0x1c>
24: ee000e15 mcr 14, 0, r0, cr0, cr5, {0}
28: e28cc001 add ip, ip, #1 ; 0x1
2c: e15c0002 cmp ip, r2
30: bafffff6 blt 10 <hvc_dcc_put_chars+0x10>
34: e1a00002 mov r0, r2
38: e12fff1e bx lr
As you can see, the value of the mrc is checked against
DCC_STATUS_TX (bit 29) and then stored in r3 for later use.
Marking the asm volatile produces the following:
00000000 <hvc_dcc_put_chars>:
0: e3a03000 mov r3, #0 ; 0x0
4: ea000007 b 28 <hvc_dcc_put_chars+0x28>
8: ee100e11 mrc 14, 0, r0, cr0, cr1, {0}
c: e3100202 tst r0, #536870912 ; 0x20000000
10: 1afffffc bne 8 <hvc_dcc_put_chars+0x8>
14: e7d10003 ldrb r0, [r1, r3]
18: ee10fe11 mrc 14, 0, pc, cr0, cr1, {0}
1c: 2afffffd bcs 18 <hvc_dcc_put_chars+0x18>
20: ee000e15 mcr 14, 0, r0, cr0, cr5, {0}
24: e2833001 add r3, r3, #1 ; 0x1
28: e1530002 cmp r3, r2
2c: bafffff5 blt 8 <hvc_dcc_put_chars+0x8>
30: e1a00002 mov r0, r2
34: e12fff1e bx lr
which looks better and actually works. Mark all the inline
assembly in this file as volatile since we don't want the
compiler to optimize away these statements or move them around
in any way.
Acked-by: Tony Lindgren <tony@atomide.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Cc: Daniel Walker <dwalker@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The RX lock is used to protect the RX buffer from concurrent access in DMA
mode between the timer and RX interrupt routines. It is independent from
the uart lock which is used to protect the TX buffer. It is possible for
a uart TX transfer to be started up from the RX interrupt handler if low
latency is enabled. So we need to split the locks to avoid deadlocking in
this situation.
In PIO mode, the RX lock is not necessary because the handle_simple_irq
and handle_level_irq functions ensure driver interrupt handlers are called
once on one core.
And now that the RX path has its own lock, the TX interrupt has nothing to
do with the RX path, so disabling it at the same time.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit 0587102cf9 replaced a direct
implementation of SIOCGICOUNT with an implementation of
tty_operations::get_icount, but it did not actually set
rs_360_ops.get_icount.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Cc: stable@kernel.org [2.6.37]
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This field is settable but did not get copied.
Signed-off-by: Ken Mills <ken.k.mills@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: stable@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit 728674a7e4 moved virtio_console.c
to drivers/tty/hvc/ under the perception of this being an hvc driver.
It was such once, but these days it has generic communication
capabilities as well, so move it to drivers/char/.
In the future, the hvc part from this file can be split off and moved
under drivers/tty/hvc/.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
CC: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
PCH_DMA is not always enabled when a user uses PCH_UART.
Since overhead of DMA is not small, in case of low frequent
communication, without DMA is better.
Thus, "select PCH_DMA" and DMADEVICES are unnecessary
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Support ML7213 device of OKI SEMICONDUCTOR.
ML7213 is companion chip of Intel Atom E6xx series for IVI(In-Vehicle Infotainment).
ML7213 is completely compatible for Intel EG20T PCH.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On some platforms, we need to restore the console speed on resume even
it was not suspended (no_console_suspend), and on others we don't have
to do that.
So don't care about the "console_suspend_enabled" and unconditionally
reset the console speed if it is a console.
This is actually a redo of ba15ab0 (Set proper console speed on resume
if console suspend is disabled) from Deepak Saxena. I also tried to
investigate more to find out if this change will break others, here is
what I've found out:
commit 891b9dd107
Author: Jason Wang <jason77.wang@gmail.com>
serial-core: restore termios settings when resume console ports
commit ca2e71aa8c
Author: Jason Wang <jason77.wang@gmail.com>
serial-core: skip call set_termios/console_start when no_console_suspend
commit 4547be7809
Author: Stanislav Brabec <sbrabec@suse.cz>
serial-core: resume serial hardware with no_console_suspend
commit ba15ab0e8d
Author: Deepak Saxena <dsaxena@laptop.org>
Set proper console speed on resume if console suspend is disabled
from ba15ab0, we learned that, even if the console suspend is disabled
(when no_console_suspend is set), we may still need to "reset the port
to the state it was in before we suspended."
Then with 4547be7, this piece of code is removed.
And then Jason Wang added that back in ca2e71a and 891b9dd, to fix
some breakage on OMAP3EVM platform. From ca2e71a we learned that the
"set_termios" things is actually needed by both console is suspended
and not suspended.
That's why I removed the console_suspended_enabled condition, and only
call console_start() when we actually suspeneded it.
I also noticed in this thread:
http://marc.info/?t=129079257100004&r=1&w=2, which talked about on
some platforms, UART HW will be cut power whether or not we set
no_console_suspend, and then on resume it does not work quite well. I
have a similar HW, and this patch fixed this issue, don't know if this
patch also works on their platforms.
[Update: Stanislav tested this patch on Zaurus and reported it improves the
situation. Thanks.]
CC: Greg KH <greg@kroah.com>
CC: Deepak Saxena <dsaxena@laptop.org>
CC: Jason Wang <jason77.wang@gmail.com>
CC: Stanislav Brabec <sbrabec@suse.cz>
CC: Daniel Drake <dsd@laptop.org>
Signed-off-by: Yin Kangkai <kangkai.yin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is used to store the spi_device ->modalias so they have to be the same
size. SPI_NAME_SIZE is 32.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: stable@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
flush_scheduled_work() is scheduled to be deprecated. Explicitly sync
flush the used work items instead. Note that before this change,
flush_scheduled_work() wouldn't have properly flushed tty->buf.work if
it were on timer.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
OMAP can do also dynamic idling so wake-up enable register should be set
also while system is running. If UART_OMAP_WER is not set, then for instance
the RX activity cannot wake up the UART port that is sleeping.
This RX wake-up feature was working when the 8250 driver was used instead
of omap-serial. Reason for this is that the 8250 doesn't set the
UART_OMAP_WER and then arch/arm/mach-omap2/pm34xx.c ends up saving and
restoring the reset default which is the same than value
OMAP_UART_WER_MOD_WKUP here.
Fix this by moving the conditional UART_OMAP_WER write from serial_omap_pm
into serial_omap_startup where wake-up bits are set unconditionally.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Cc: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Magic SysRq key is not working for OMAP on new serial
console ttyOx because SUPPORT_SYSRQ is not defined
for omap-serial.
This patch defines SUPPORT_SYSRQ in omap-serial and
enables handling of Magic SysRq character.
Further there is an issue of losing first break character.
Removing the reset of the lsr_break_flag fixes this issue.
Signed-off-by: Thomas Weber <weber@corscience.de>
Acked-by: Govindraj.R <govindraj.raja@ti.com>
Tested-by: Manjunath G Kondaiah <manjugk@ti.com>
Acked-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some platform attributes (e.g. max_hz, use_dma) were being intuited
from the modem type. These things should be specified by the platform
data.
Added max_hz, use_dma to ifx_modem_platform_data definition,
replaced is_6160 w/ modem_type, and changed clients accordingly
Signed-off-by: Russ Gorby <russ.gorby@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is kind of a revert for commit 669b7a0938 "hsu: add a periodic
timer to check dma rx channel", which is a workaround for a bug in A0
stepping silicon, where a dma rx data timeout is missing for some case.
Since new silicon has fixed it and the old version is phasing out, no
need to carry on it any more.
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
sport->port.irq is unsigned, check for <0 doesn't make sense.
Explicitly cast it to int to check for error.
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'tty-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6:
tty/serial: fix apbuart build
n_hdlc: fix read and write locking
serial: unbreak billionton CF card
tty: use for_each_console() and WARN() on sysfs failures
vt: fix issue when fbcon wants to takeover a second time.
Fix up trivial conflict in drivers/tty/tty_io.c
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: wacom - pass touch resolution to clients through input_absinfo
Input: wacom - add 2 Bamboo Pen and touch models
Input: sysrq - ensure sysrq_enabled and __sysrq_enabled are consistent
Input: sparse-keymap - fix KEY_VSW handling in sparse_keymap_setup
Input: tegra-kbc - add tegra keyboard driver
Input: gpio_keys - switch to using request_any_context_irq
Input: serio - allow registered drivers to get status flag
Input: ct82710c - return proper error code for ct82c710_open
Input: bu21013_ts - added regulator support
Input: bu21013_ts - remove duplicate resolution parameters
Input: tnetv107x-ts - don't treat NULL clk as an error
Input: tnetv107x-keypad - don't treat NULL clk as an error
Fix up trivial conflicts in drivers/input/keyboard/Makefile due to
additions of tc3589x/Tegra drivers
The -rt patches change the console_semaphore to console_mutex. As a
result, a quite large chunk of the patches changes all
acquire/release_console_sem() to acquire/release_console_mutex()
This commit makes things use more neutral function names which dont make
implications about the underlying lock.
The only real change is the return value of console_trylock which is
inverted from try_acquire_console_sem()
This patch also paves the way to switching console_sem from a semaphore to
a mutex.
[akpm@linux-foundation.org: coding-style fixes]
[akpm@linux-foundation.org: make console_trylock return 1 on success, per Geert]
Signed-off-by: Torben Hohn <torbenh@gmx.de>
Cc: Thomas Gleixner <tglx@tglx.de>
Cc: Greg KH <gregkh@suse.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
lh7a40x has only been receiving updates for updates to generic code.
The last involvement from the maintainer according to the git logs was
in 2006. As such, it is a maintainence burden with no benefit.
This gets rid of two defconfigs.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix locking in read and write code of n_hdlc line discipline.
2.6.36 replaced lock_kernel() with tty_lock(). The tty mutex is not
dropped automatically when the thread sleeps like the BKL. This results
in a blocked read or write holding the tty mutex and stalling operations
by other devices that use the tty mutex.
A review of n_hdlc read and write code shows:
1. neither BKL or tty mutex are required for correct operation
2. read can block while read data is available if data is posted
between availability check and call to interruptible_sleep_on()
3. write does not set process state to TASK_INTERRUPTIBLE
on each pass through the processing loop which can cause
unneeded scheduling of the thread
The unnecessary tty mutex references have been removed.
Read changed to use same code as n_tty read
for completing reads and blocking.
Write corrected to set process state to TASK_INTERRUPTIBLE on each pass
through processing loop.
Signed-off-by: Paul Fulghum <paulkf@microgate.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Unbreak Billionton CF bluetooth card. This actually fixes a regression
on zaurus.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes the build warnings in the tty code, and uses the proper
function for iterating over the console devices.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
With framebuffer handover and multiple GPUs, we get into a
position where the fbcon unbinds the vesafb framebuffer for GPU 1,
but we still have a radeon framebuffer bound from GPU 0, so
we don't unregister the console driver. Then when we tried to bind
the new radeon framebuffer for GPU1 we never get to the bind
call as we fail due to the console being registered already.
This changes the return value to -EBUSY when the driver is
already registered and continues to bind for -EBUSY.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* akpm:
kernel/smp.c: consolidate writes in smp_call_function_interrupt()
kernel/smp.c: fix smp_call_function_many() SMP race
memcg: correctly order reading PCG_USED and pc->mem_cgroup
backlight: fix 88pm860x_bl macro collision
drivers/leds/ledtrig-gpio.c: make output match input, tighten input checking
MAINTAINERS: update Atmel AT91 entry
mm: fix truncate_setsize() comment
memcg: fix rmdir, force_empty with THP
memcg: fix LRU accounting with THP
memcg: fix USED bit handling at uncharge in THP
memcg: modify accounting function for supporting THP better
fs/direct-io.c: don't try to allocate more than BIO_MAX_PAGES in a bio
mm: compaction: prevent division-by-zero during user-requested compaction
mm/vmscan.c: remove duplicate include of compaction.h
memblock: fix memblock_is_region_memory()
thp: keep highpte mapped until it is no longer needed
kconfig: rename CONFIG_EMBEDDED to CONFIG_EXPERT
* 'tty-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6:
tty: update MAINTAINERS file due to driver movement
tty: move drivers/serial/ to drivers/tty/serial/
tty: move hvc drivers to drivers/tty/hvc/
The serial drivers are really just tty drivers, so move them to
drivers/tty/ to make things a bit neater overall.
This is part of the tty/serial driver movement proceedure as proposed by
Arnd Bergmann and approved by everyone involved a number of months ago.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Rogier Wolff <R.E.Wolff@bitwizard.nl>
Cc: Michael H. Warfield <mhw@wittsend.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
As requested by Arnd Bergmann, the hvc drivers are now
moved to the drivers/tty/hvc/ directory. The virtio_console.c driver
was also moved, as it required the hvc_console.h file to be able to be
built, and it really is a hvc driver.
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'tty-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6: (36 commits)
serial: apbuart: Fixup apbuart_console_init()
TTY: Add tty ioctl to figure device node of the system console.
tty: add 'active' sysfs attribute to tty0 and console device
drivers: serial: apbuart: Handle OF failures gracefully
Serial: Avoid unbalanced IRQ wake disable during resume
tty: fix typos/errors in tty_driver.h comments
pch_uart : fix warnings for 64bit compile
8250: fix uninitialized FIFOs
ip2: fix compiler warning on ip2main_pci_tbl
specialix: fix compiler warning on specialix_pci_tbl
rocket: fix compiler warning on rocket_pci_ids
8250: add a UPIO_DWAPB32 for 32 bit accesses
8250: use container_of() instead of casting
serial: omap-serial: Add support for kernel debugger
serial: fix pch_uart kconfig & build
drivers: char: hvc: add arm JTAG DCC console support
RS485 documentation: add 16C950 UART description
serial: ifx6x60: fix memory leak
serial: ifx6x60: free IRQ on error
Serial: EG20T: add PCH_UART driver
...
Fixed up conflicts in drivers/serial/apbuart.c with evil merge that
makes the code look fairly sane (unlike either side).
tty: add 'active' sysfs attribute to tty0 and console device
Userspace can query the actual virtual console, and the configured
console devices behind /dev/tt0 and /dev/console.
The last entry in the list of devices is the active device, analog
to the console= kernel command line option.
The attribute supports poll(), which is raised when the virtual
console is changed or /dev/console is reconfigured.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
index 0000000..b138b66
gsm_data_alloc buffer allocation could fail and it is not being checked.
Add check for allocated buffer and return if the buffer allocation
fails.
Signed-off-by: Ken Mills <ken.k.mills@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: stable@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix message length handling when building header
When the message length is greater than 127, the length field in the header
is built incorrectly. According to the spec, when the length is less than 128
the length field is a single byte formatted as: bbbbbbb1. When it is greater
than 127 then the field is two bytes of the format: bbbbbbb0 bbbbbbbb.
Signed-off-by: Ken Mills <ken.k.mills@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: stable@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'tty-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6:
serial: mfd: adjust the baud rate setting
TTY: open/hangup race fixup
TTY: don't allow reopen when ldisc is changing
NET: wan/x25, fix ldisc->open retval
TTY: ldisc, fix open flag handling
serial8250: Mark console as CON_ANYTIME
Like in the "TTY: don't allow reopen when ldisc is changing" patch,
this one fixes a TTY WARNING as described in the option 1) there:
1) __tty_hangup from tty_ldisc_hangup to tty_ldisc_enable. During this
section tty_lock is held. However tty_lock is temporarily dropped in
the middle of the function by tty_ldisc_hangup.
The fix is to introduce a new flag which we set during the unlocked
window and check it in tty_reopen too. The flag is TTY_HUPPING and is
cleared after TTY_HUPPED is set.
While at it, remove duplicate TTY_HUPPED set_bit. The one after
calling ops->hangup seems to be more correct. But anyway, we hold
tty_lock, so there should be no difference.
Also document the function it does that kind of crap.
Nicely reproducible with two forked children:
static void do_work(const char *tty)
{
if (signal(SIGHUP, SIG_IGN) == SIG_ERR) exit(1);
setsid();
while (1) {
int fd = open(tty, O_RDWR|O_NOCTTY);
if (fd < 0) continue;
if (ioctl(fd, TIOCSCTTY)) continue;
if (vhangup()) continue;
close(fd);
}
exit(0);
}
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Reported-by: <Valdis.Kletnieks@vt.edu>
Reported-by: Kyle McMartin <kyle@mcmartin.ca>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There are many WARNINGs like the following reported nowadays:
WARNING: at drivers/tty/tty_io.c:1331 tty_open+0x2a2/0x49a()
Hardware name: Latitude E6500
Modules linked in:
Pid: 1207, comm: plymouthd Not tainted 2.6.37-rc3-mmotm1123 #3
Call Trace:
[<ffffffff8103b189>] warn_slowpath_common+0x80/0x98
[<ffffffff8103b1b6>] warn_slowpath_null+0x15/0x17
[<ffffffff8128a3ab>] tty_open+0x2a2/0x49a
[<ffffffff810fd53f>] chrdev_open+0x11d/0x146
...
This means tty_reopen is called without TTY_LDISC set. For further
considerations, note tty_lock is held in tty_open. TTY_LDISC is cleared in:
1) __tty_hangup from tty_ldisc_hangup to tty_ldisc_enable. During this
section tty_lock is held. However tty_lock is temporarily dropped in
the middle of the function by tty_ldisc_hangup.
2) tty_release via tty_ldisc_release till the end of tty existence. If
tty->count <= 1, tty_lock is taken, TTY_CLOSING bit set and then
tty_ldisc_release called. tty_reopen checks TTY_CLOSING before checking
TTY_LDISC.
3) tty_set_ldisc from tty_ldisc_halt to tty_ldisc_enable. We:
* take tty_lock, set TTY_LDISC_CHANGING, put tty_lock
* call tty_ldisc_halt (clear TTY_LDISC), tty_lock is _not_ held
* do some other work
* take tty_lock, call tty_ldisc_enable (set TTY_LDISC), put
tty_lock
I cannot see how 2) can be a problem, as there I see no race. OTOH, 1)
and 3) can happen without problems. This patch the case 3) by checking
TTY_LDISC_CHANGING along with TTY_CLOSING in tty_reopen. 1) will be
fixed in the following patch.
Nicely reproducible with two processes:
while (1) {
fd = open("/dev/ttyS1", O_RDWR);
if (fd < 0) {
warn("open");
continue;
}
close(fd);
}
--------
while (1) {
fd = open("/dev/ttyS1", O_RDWR);
ld1 = 0; ld2 = 2;
while (1) {
ioctl(fd, TIOCSETD, &ld1);
ioctl(fd, TIOCSETD, &ld2);
}
close(fd);
}
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Reported-by: <Valdis.Kletnieks@vt.edu>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When a concrete ldisc open fails in tty_ldisc_open, we forget to clear
TTY_LDISC_OPEN. This causes a false warning on the next ldisc open:
WARNING: at drivers/char/tty_ldisc.c:445 tty_ldisc_open+0x26/0x38()
Hardware name: System Product Name
Modules linked in: ...
Pid: 5251, comm: a.out Tainted: G W 2.6.32-5-686 #1
Call Trace:
[<c1030321>] ? warn_slowpath_common+0x5e/0x8a
[<c1030357>] ? warn_slowpath_null+0xa/0xc
[<c119311c>] ? tty_ldisc_open+0x26/0x38
[<c11936c5>] ? tty_set_ldisc+0x218/0x304
...
So clear the bit when failing...
Introduced in c65c9bc3ef (tty: rewrite the ldisc locking) back in
2.6.31-rc1.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Alan Cox <alan@linux.intel.com>
Reported-by: Sergey Lapin <slapin@ossfans.org>
Tested-by: Sergey Lapin <slapin@ossfans.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: fix typo in keycode validation supporting large scancodes
Input: aiptek - tighten up permissions on sysfs attributes
Input: sysrq - pass along lone Alt + SysRq
[Original From Ken Mills but I redid it using pr_ helpers instead]
Also fix up coding style, there are two warnings left but that is where
the CodingStyle tools blow up because they cannot handle
if (blah) {
foo
} else switch (x) {
case 1:
}
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The mux supports several encoding schemes. Encoding 0 is a "not
recommended" mode still sometimes used. This has now been tested with
hardware that supports this mode, and found wanting.
Fix the FCS handling in this mode and correct the state machine.
Signed-off-by: Ken Mills <ken.k.mills@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If the mux is configured with a large mru/mtu the existing code gets the
byte ordering wrong for the header.
Signed-off-by: Ken Mills <ken.k.mills@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The n2 field is settable but didn't get propogated
Signed-off-by: Ken Mills <ken.k.mills@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Kay Sievers pointed out that usage of POLLIN is well defined by POSIX,
and the current usage here doesn't follow that definition. So let's
duplicate the same semantics as implemented by sysfs_poll() instead.
Signed-off-by: Nicolas Pitre <nicolas.pitre@canonical.com>
Acked-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A kernel BUG when bluetooth rfcomm connection drop while the associated
serial port is open is sometime triggered.
It seems that the line discipline can disappear between the
tty_ldisc_put and tty_ldisc_get. This patch fall back to the N_TTY line
discipline if the previous discipline is not available anymore.
Signed-off-by: Philippe Retornaz <philippe.retornaz@epfl.ch>
Acked-by: Alan Cox <alan@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It was removed in 65b770468e (tty-ldisc: turn ldisc user count into
a proper refcount), but we need to wait for last user to quit the
ldisc before we close it in tty_set_ldisc.
Otherwise weird things start to happen. There might be processes
waiting in tty_read->n_tty_read on tty->read_wait for input to appear
and at that moment, a change of ldisc is fatal. n_tty_close is called,
it frees read_buf and the waiting process is still in the middle of
reading and goes nuts after it is woken.
Previously we prevented close to happen when others are in ldisc ops
by tty_ldisc_wait_idle in tty_set_ldisc. But the commit above removed
that. So revoke the change and test whether there is 1 user (=we), and
allow the close then.
We can do that without ldisc/tty locks, because nobody else can open
the device due to TTY_LDISC_CHANGING bit set, so we in fact wait for
everybody to leave.
I don't understand why tty_ldisc_lock would be needed either when the
counter is an atomic variable, so this is a lockless
tty_ldisc_wait_idle.
On the other hand, if we fail to wait (timeout or signal), we have to
reenable the halted ldiscs, so we take ldisc lock and reuse the setup
path at the end of tty_set_ldisc.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Tested-by: Sebastian Andrzej Siewior <bigeasy@breakpoint.cc>
LKML-Reference: <20101031104136.GA511@Chamillionaire.breakpoint.cc>
LKML-Reference: <1287669539-22644-1-git-send-email-jslaby@suse.cz>
Cc: Alan Cox <alan@linux.intel.com>
Cc: stable@kernel.org [32, 33, 36]
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There's a small window inside the flush_to_ldisc function,
where the tty is unlocked and calling ldisc's receive_buf
function. If in this window new buffer is added to the tty,
the processing might never leave the flush_to_ldisc function.
This scenario will hog the cpu, causing other tty processing
starving, and making it impossible to interface the computer
via tty.
I was able to exploit this via pty interface by sending only
control characters to the master input, causing the flush_to_ldisc
to be scheduled, but never actually generate any output.
To reproduce, please run multiple instances of following code.
- SNIP
#define _XOPEN_SOURCE
#include <stdlib.h>
#include <stdio.h>
#include <sys/types.h>
#include <sys/stat.h>
#include <fcntl.h>
int main(int argc, char **argv)
{
int i, slave, master = getpt();
char buf[8192];
sprintf(buf, "%s", ptsname(master));
grantpt(master);
unlockpt(master);
slave = open(buf, O_RDWR);
if (slave < 0) {
perror("open slave failed");
return 1;
}
for(i = 0; i < sizeof(buf); i++)
buf[i] = rand() % 32;
while(1) {
write(master, buf, sizeof(buf));
}
return 0;
}
- SNIP
The attached patch (based on -next tree) fixes this by checking on the
tty buffer tail. Once it's reached, the current work is rescheduled
and another could run.
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
Cc: stable <stable@kernel.org>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The autogenerated files (consolemap_deftbl.c and defkeymap.c) need to
be ignored by git, so move the .gitignore file that was doing it to the
properly location now that the files have moved as well.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The vt and other related code is moved into the drivers/tty/vt directory.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The tty code should be in its own subdirectory and not in the char
driver with all of the cruft that is currently there.
Based on work done by Arnd Bergmann <arnd@arndb.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Tobias Klauser
Feng Tang
Greg Kroah-Hartman
Kukjin Kim
Linus Torvalds
Kay Sievers
Alan Cox
Jiri Olsa
Viktar Palstsiuk
Niranjana Vishwanathapura
Yin Kangkai
Russ Gorby
Mandeep Singh Baines
Mike Frysinger
Arthur Taylor
Jesper Juhl
Tejun Heo
Greg Ungerer
Paul Bolle
Paul Mundt
Sascha Hauer
Stephen Boyd
Sonic Zhang
Ben Hutchings
Ken Mills
Amit Shah
Tomoya MORINAGA
Dan Carpenter
Jarkko Nikula
Thomas Weber
Vasiliy Kulikov
Torben Hohn
David Brown
Russell King
Randy Dunlap
Paul Fulghum
Pavel Machek
Dave Airlie
Werner Fink
Jiri Slaby
Nicolas Pitre
Philippe Rétornaz