This is in preparation of removing ide_atapi_pc. Expose the buffer as an
argument to ide_queue_pc_tail with later replacing it with local buffer
or even kmalloc'ed one if needed due to stack usage constraints.
Also, add the possibility of passing a NULL-ptr buffer for cmds which
don't transfer data besides the cdb. While at it, switch to local buffer
in idetape_get_mode_sense_results().
There should be no functional change resulting from this patch.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
This is in preparation for removing ide_atapi_pc.
There should be no functional change resulting from this patch.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Now that we have rq->resid_len, use it to account partial completion
amount during the lifetime of an rq, decrementing it on each successful
transfer. As a result, get rid of now unused pc->xferred.
While at it, remove noisy debug call in ide_prep_sense.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
After the recent struct request cleanups, blk_rq_bytes() is guaranteed
to be valid and is the current total length of the rq's bio. Use that
instead of pc->req_xfer in the do_request() path after the command has
been queued
The remaining usage of pc->req_xfer now is only until we map the rq to a
bio.
While at it:
- remove local caching of rq completion length in ide_tape_issue_pc()
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
ide-tape had a potential bug for fs requests when preparing the command
packet: it was writing the transfer length as a number of fixed blocks.
However, the block layer implies 512 byte blocks and ide-tape can have
other block sizes so account for that too.
ide-floppy does this calculation properly with the block size factor
(floppy->bs_factor).
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Till now block layer allowed two separate modes of request execution.
A request is always acquired from the request queue via
elv_next_request(). After that, drivers are free to either dequeue it
or process it without dequeueing. Dequeue allows elv_next_request()
to return the next request so that multiple requests can be in flight.
Executing requests without dequeueing has its merits mostly in
allowing drivers for simpler devices which can't do sg to deal with
segments only without considering request boundary. However, the
benefit this brings is dubious and declining while the cost of the API
ambiguity is increasing. Segment based drivers are usually for very
old or limited devices and as converting to dequeueing model isn't
difficult, it doesn't justify the API overhead it puts on block layer
and its more modern users.
Previous patches converted all block low level drivers to dequeueing
model. This patch completes the API transition by...
* renaming elv_next_request() to blk_peek_request()
* renaming blkdev_dequeue_request() to blk_start_request()
* adding blk_fetch_request() which is combination of peek and start
* disallowing completion of queued (not started) requests
* applying new API to all LLDs
Renamings are for consistency and to break out of tree code so that
it's apparent that out of tree drivers need updating.
[ Impact: block request issue API cleanup, no functional change ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Mike Miller <mike.miller@hp.com>
Cc: unsik Kim <donari75@gmail.com>
Cc: Paul Clements <paul.clements@steeleye.com>
Cc: Tim Waugh <tim@cyberelk.net>
Cc: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Laurent Vivier <Laurent@lvivier.info>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Borislav Petkov <petkovbb@googlemail.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Alex Dubov <oakad@yahoo.com>
Cc: Pierre Ossman <drzeus@drzeus.cx>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>
Cc: Stefan Weinhuber <wein@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
ide generally has single request in flight and tracks it using
hwif->rq and all state handlers follow the following convention.
* ide_started is returned if the request is in flight.
* ide_stopped is returned if the queue needs to be restarted. The
request might or might not have been processed fully or partially.
* hwif->rq is set to NULL, when an issued request completes.
So, dequeueing model can be implemented by dequeueing after fetch,
requeueing if hwif->rq isn't NULL on ide_stopped return and doing
about the same thing on completion / port unlock paths. These changes
can be made in ide-io proper.
In addition to the above main changes, the following updates are
necessary.
* ide-cd shouldn't dequeue a request when issuing REQUEST SENSE for it
as the request is already dequeued.
* ide-atapi uses request queue as stack when issuing REQUEST SENSE to
put the REQUEST SENSE in front of the failed request. This now
needs to be done using requeueing.
[ Impact: dequeue in-flight request ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Borislav Petkov <petkovbb@googlemail.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
With recent unification of fields, it's now guaranteed that
rq->data_len always equals blk_rq_bytes(). Convert all direct users
to accessors.
[ Impact: convert direct rq->data_len usages to blk_rq_bytes() ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Borislav Petkov <petkovbb@googlemail.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
ide doesn't manipulate request fields anymore and thus all hard and
their soft equivalents are always equal. Convert all references to
accessors.
[ Impact: use pos and nr_sectors accessors ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Borislav Petkov <petkovbb@googlemail.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Implement accessors - blk_rq_pos(), blk_rq_sectors() and
blk_rq_cur_sectors() which return rq->hard_sector, rq->hard_nr_sectors
and rq->hard_cur_sectors respectively and convert direct references of
the said fields to the accessors.
This is in preparation of request data length handling cleanup.
Geert : suggested adding const to struct request * parameter to accessors
Sergei : spotted error in patch description
[ Impact: cleanup ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Acked-by: Stephen Rothwell <sfr@canb.auug.org.au>
Tested-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Ackec-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Borislav Petkov <petkovbb@googlemail.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
rq->data_len served two purposes - the length of data buffer on issue
and the residual count on completion. This duality creates some
headaches.
First of all, block layer and low level drivers can't really determine
what rq->data_len contains while a request is executing. It could be
the total request length or it coulde be anything else one of the
lower layers is using to keep track of residual count. This
complicates things because blk_rq_bytes() and thus
[__]blk_end_request_all() relies on rq->data_len for PC commands.
Drivers which want to report residual count should first cache the
total request length, update rq->data_len and then complete the
request with the cached data length.
Secondly, it makes requests default to reporting full residual count,
ie. reporting that no data transfer occurred. The residual count is
an exception not the norm; however, the driver should clear
rq->data_len to zero to signify the normal cases while leaving it
alone means no data transfer occurred at all. This reverse default
behavior complicates code unnecessarily and renders block PC on some
drivers (ide-tape/floppy) unuseable.
This patch adds rq->resid_len which is used only for residual count.
While at it, remove now unnecessasry blk_rq_bytes() caching in
ide_pc_intr() as rq->data_len is not changed anymore.
Boaz : spotted missing conversion in osd
Sergei : spotted too early conversion to blk_rq_bytes() in ide-tape
[ Impact: cleanup residual count handling, report 0 resid by default ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Borislav Petkov <petkovbb@googlemail.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Mike Miller <mike.miller@hp.com>
Cc: Eric Moore <Eric.Moore@lsi.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Doug Gilbert <dgilbert@interlog.com>
Cc: Mike Miller <mike.miller@hp.com>
Cc: Eric Moore <Eric.Moore@lsi.com>
Cc: Darrick J. Wong <djwong@us.ibm.com>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Cc: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
rq->sector is set to the tape->first_frame but it's never actually
used and not even in the correct unit (512 byte sectors). Don't set
it.
[ Impact: cleanup ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Borislav Petkov <petkovbb@gmail.com>
Acked-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Some time ago we had to disable init_hwif callback for PowerPC builds.
That was because of a historical IRQ overwrite in the driver, which
was causing IDE malfunction on the MPC8610HPCD PowerPC boards.
It's unclear whether this overwrite is still useful, but it is proven
to cause a bit of harm, and today some PowerPC targets (Xilinx ML510,
as reported by Roderick Colenbrander) need the init_hwif, so we have
to re-enable it and remove the overwrite.
Reported-by: Roderick Colenbrander <thunderbird2k@gmail.com>
Suggested-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Original patch (dfa4411cc3) was buggy.
This is a more proper fix which introduces blk_rq_quiet() macro
alleviating the need for dumb, too short caching variables.
Thanks to Helge Deller and Bart for debugging this.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Reported-and-tested-by: Helge Deller <deller@gmx.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Impact: drop unnecessary code
Now that everything uses bio and block operations, there is no need to
reset request fields manually when retrying a request. Every field is
guaranteed to be always valid. Drop unnecessary request field
resetting from ide_dma_timeout_retry().
Signed-off-by: Tejun Heo <tj@kernel.org>
Impact: remove code path which is no longer necessary
All IDE data transfers now use rq->bio. Simplify ide_map_sg()
accordingly.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Impact: remove fields and code paths which are no longer necessary
Now that ide-tape uses standard mechanisms to transfer data, special
case handling for bh handling can be dropped from ide-atapi. Drop the
followings.
* pc->cur_pos, b_count, bh and b_data
* drive->pc_update_buffers() and pc_io_buffers().
Signed-off-by: Tejun Heo <tj@kernel.org>
Impact: cleanup
idetape_chrdev_read/write() functions are unnecessarily complex when
everything can be handled in a single loop. Collapse
idetape_add_chrdev_read/write_request() into the rw functions and
simplify the implementation.
Signed-off-by: Tejun Heo <tj@kernel.org>
Impact: cleanup
Byte size is what most issue functions deal with, make
idetape_queue_rw_tail() and its wrappers take byte size instead of
sector counts. idetape_chrdev_read() and write() functions are
converted to use tape->buffer_size instead of ctl from tape->cap.
This cleans up code a little bit and will ease the next r/w
reimplementation.
Signed-off-by: Tejun Heo <tj@kernel.org>
Impact: kill now unnecessary idetape_bh
With everything using standard mechanisms, there is no need for
idetape_bh anymore. Kill it and use tape->buf, cur and valid to
describe data buffer instead.
Changes worth mentioning are...
* idetape_queue_rq_tail() now always queue tape->buf and and adjusts
buffer state properly before completion.
* idetape_pad_zeros() clears the buffer only once.
Signed-off-by: Tejun Heo <tj@kernel.org>
Impact: use standard way to transfer data
ide-tape uses rq in an interesting way. For r/w requests, rq->special
is used to carry a private buffer management structure idetape_bh and
rq->nr_sectors and current_nr_sectors are initialized to the number of
idetape blocks which isn't necessary 512 bytes. Also,
rq->current_nr_sectors is used to report back the residual count in
units of idetape blocks.
This peculiarity taxes both block layer and ide. ide-atapi has
different paths and hooks to accomodate it and what a rq means becomes
quite confusing and making changes at the block layer becomes quite
difficult and error-prone.
This patch makes ide-tape use bio instead. With the previous patch,
ide-tape currently is using single contiguos buffer so replacing it
isn't difficult. Data buffer is mapped into bio using
blk_rq_map_kern() in idetape_queue_rw_tail(). idetape_io_buffers()
and idetape_update_buffers() are dropped and pc->bh is set to null to
tell ide-atapi to use standard data transfer mechanism and idetape_bh
byte counts are updated by the issuer on completion using the residual
count.
This change also nicely removes the FIXME in ide_pc_intr() where
ide-tape rqs need to be completed using ide_rq_bytes() instead of
blk_rq_bytes() (although this didn't really matter as the request
didn't have bio).
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jens Axboe <jens.axboe@oracle.com>
Impact: simpler buffer allocation and handling, kills OOM, fix DMA transfers
ide-tape has its own multiple buffer mechanism using struct
idetape_bh. It allocates buffer with decreasing order-of-two
allocations so that it results in minimum number of segments.
However, the implementation is quite complex and works in a way that
no other block or ide driver works necessitating a lot of special case
handling.
The benefit this complex allocation scheme brings is questionable as
PIO or DMA the number of segments (16 maximum) doesn't make any
noticeable difference and it also doesn't negate the need for multiple
order allocation which can fail under memory pressure or high
fragmentation although it does lower the highest order necessary by
one when the buffer size isn't power of two.
As the first step to remove the custom buffer management, this patch
makes ide-tape allocate single continous buffer. The maximum order is
four. I doubt the change would cause any trouble but if it ever
matters, it should be converted to regular sg mechanism like everyone
else and even in that case dropping custom buffer handling and moving
to standard mechanism first make sense as an intermediate step.
This patch makes the first bh to contain the whole buffer and drops
multi bh handling code. Following patches will make further changes.
This patch has the side effect of killing OOM triggered by allocation
path and fixing DMA transfers. Previously, bug in alloc path
triggered OOM on command issue and commands were passed to DMA engine
without DMA-mapping all the segments.
Signed-off-by: Tejun Heo <tj@kernel.org>
Impact: allow residual count implementation in ->pc_callback()
rq->data_len has two duties - carrying the number of input bytes on
issue and carrying residual count back to the issuer on completion.
ide-atapi completion callback ->pc_callback() is the right place to do
this but currently ide-atapi depends on rq->data_len carrying the
original request size after calling ->pc_callback() to complete the pc
request.
This patch makes ide_pc_intr(), ide_tape_issue_pc() and
ide_floppy_issue_pc() cache length to complete before calling
->pc_callback() so that it can modify rq->data_len as necessary.
Note: As using rq->data_len for two purposes can make cases like this
incorrect in subtle ways, future changes will introduce separate
field for residual count.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jens Axboe <jens.axboe@oracle.com>
Impact: fix infinite retry loop
After a command failed, ide-tape and floppy inserts REQUEST_SENSE in
front of the failed command and according to the result, sets
pc->retries, flags and errors. After REQUEST_SENSE is complete, the
failed command is again at the front of the queue and if the verdict
was to terminate the request, the issue functions tries to complete it
directly by calling drive->pc_callback() and returning ide_stopped.
However, drive->pc_callback() doesn't complete a request. It only
prepares for completion of the request. As a result, this creates an
infinite loop where the failed request is retried perpetually.
Fix it by actually ending the request by calling ide_complete_rq().
Signed-off-by: Tejun Heo <tj@kernel.org>
Impact: cleanup rq->data usage
ide-pm uses rq->data to carry pointer to struct request_pm_state
through request queue and rq->special is used to carray pointer to
local struct ide_cmd, which isn't necessary. Use rq->special for
request_pm_state instead and use local ide_cmd in
ide_start_power_step().
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Impact: unify request data buffer handling
rq->data is used mostly to pass kernel buffer through request queue
without using bio. There are only a couple of places which still do
this in kernel and converting to bio isn't difficult.
This patch converts ide-cd and atapi to use bio instead of rq->data
for request sense and internal pc commands. With previous change to
unify sense request handling, this is relatively easily achieved by
adding blk_rq_map_kern() during sense_rq prep and PC issue.
If blk_rq_map_kern() fails for sense, the error is deferred till sense
issue and aborts the failed command which triggered the sense. Note
that this is a slim possibility as sense prep is done on each command
issue, so for the above condition to actually trigger, all preps since
the last sense issue till the issue of the request which would require
a sense should fail.
* do_request functions might sleep now. This should be okay as ide
request_fn - do_ide_request() - is invoked only from make_request
and plug work. Make sure this is the case by adding might_sleep()
to do_ide_request().
* Functions which access the read sense data before the sense request
is complete now should access bio_data(sense_rq->bio) as the sense
buffer might have been copied during blk_rq_map_kern().
* ide-tape updated to map sg.
* cdrom_do_block_pc() now doesn't have to deal with REQ_TYPE_ATA_PC
special case. Simplified.
* tp_ops->output/input_data path dropped from ide_pc_intr().
Signed-off-by: Tejun Heo <tj@kernel.org>
Since we're issuing REQ_TYPE_SENSE now we need to allow those types of
rqs in the ->do_request callbacks. As a future improvement, sense_len
assignment might be unified across all ATAPI devices. Borislav to
check with specs and test.
As a result, get rid of ide_queue_pc_head() and
drive->request_sense_rq.
tj: * Init request sense ide_atapi_pc from sense request. In the
longer timer, it would probably better to fold
ide_create_request_sense_cmd() into its only current user -
ide_floppy_get_format_progress().
* ide_retry_pc() no longer takes @disk.
CC: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
CC: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Preallocate a sense request in the ->do_request method and reinitialize
it only on demand, in case it's been consumed in the IRQ handler path.
The reason for this is that we don't want to be mapping rq to bio in
the IRQ path and introduce all kinds of unnecessary hacks to the block
layer.
tj: * Both user and kernel PC requests expect sense data to be stored
in separate storage other than drive->sense_data. Copy sense
data to rq->sense on completion if rq->sense is not NULL. This
fixes bogus sense data on PC requests.
As a result, remove cdrom_queue_request_sense.
CC: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
CC: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This is in preparation of removing the queueing of a sense request out
of the IRQ handler path.
Use struct request_sense as a general sense buffer for all ATAPI
devices ide-{floppy,tape,cd}.
tj: * blk_get_request(__GFP_WAIT) can't be called from do_request() as
it can cause deadlock. Converted to use inline struct request
and blk_rq_init().
* Added xfer / cdb len selection depending on device type.
* All sense prep logics folded into ide_prep_sense() which never
fails.
* hwif->rq clearing and sense_rq used handling moved into
ide_queue_sense_rq().
* blk_rq_map_kern() conversion is moved to later patch.
CC: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
CC: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Impact: rq->buffer usage cleanup
ide-cd uses rq->buffer to carry pointer to the original request when
issuing REQUEST_SENSE. Use rq->special instead.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Impact: rq->buffer usage cleanup
ide-atapi uses rq->buffer as private opaque value for internal special
requests. rq->special isn't used for these cases (the only case where
rq->special is used is for ide-tape rw requests). Use rq->special
instead.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Impact: rq->buffer usage cleanup
ide_raw_taskfile() directly uses rq->buffer to carry pointer to the
data buffer. This complicates both block interface and ide backend
request handling. Use blk_rq_map_kern() instead and drop special
handling for REQ_TYPE_ATA_TASKFILE from ide_map_sg().
Note that REQ_RW setting is moved upwards as blk_rq_map_kern() uses it
to initialize bio rw flag.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Impact: remove unnecessary code path
Block pc requests always use bio and rq->data is always NULL. No need
to worry about !rq->bio cases in idefloppy_block_pc_cmd(). Note that
ide-atapi uses ide_pio_bytes() for bio PIO transfer which handle sg
fine.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Impact: code simplification
ide_cd_request_sense_fixup() clears the tail of the sense buffer if
the device didn't completely fill it. This patch makes
cdrom_queue_request_sense() clear the sense buffer before issuing the
command instead of clearing it afterwards. This simplifies code and
eases future changes.
Signed-off-by: Tejun Heo <tj@kernel.org>
Impact: fix an oops which always triggers
ide_tape_issue_pc() assumed drive->pc isn't NULL on invocation when
checking for back-to-back request sense issues but drive->pc can be
NULL and even when it's not NULL, it's not safe to dereference it once
the previous command is complete because pc could have been freed or
was on stack. Kill back-to-back REQUEST_SENSE detection.
Signed-off-by: Tejun Heo <tj@kernel.org>
Bugfixes noted by checking the code against the controller
documentation (TI document number SPRUE21):
- Remove declarations for eight non-existent registers (!);
and remove accesses to two of them.
- Remove access to various non-existent bitfields in some of
the registers which *do* exist (those fields must-be-zero).
- Provide comment to replace bogus reset logic (removed above,
it relied on non-existent bitfields). Resets require GPIO
help; this driver doesn't currently know about that.
With some minor cleanup: relocate a comment, avoid an extra
lookup of the PIO timings.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
My laptop (Acer Travelmate 660) always cuts the power when rebooting
which causes the disk to emergency-park it's head.
Add a dmi check to stop disk as for shutdown on this laptop.
Signed-off-by: Bruno Prémont <bonbons@linux-vserver.org>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
With 2.6.30-rc2 I face a kernel crash on the 32bit hppa architecture
due to ide-cd when udev creates the device nodes at startup:
Kernel Fault: Code=26 regs=8ed34c40 (Addr=00000024)
IASQ: 00000000 00000000 IAOQ: 1034b5ac 1034b5b0
IIR: 4ab30048 ISR: 00000000 IOR: 00000024
CPU: 0 CR30: 8ed34000 CR31: ffff55ff
ORIG_R28: 00000000
IAOQ[0]: ide_complete_rq+0x2c/0x70
IAOQ[1]: ide_complete_rq+0x30/0x70
RP(r2): cdrom_newpc_intr+0x178/0x46c
Backtrace:
[<1035c608>] cdrom_newpc_intr+0x178/0x46c
[<1034c494>] ide_intr+0x1b0/0x214
[<1016d284>] handle_IRQ_event+0x70/0x150
[<1016d4b0>] __do_IRQ+0x14c/0x1cc
[<102f7864>] superio_interrupt+0x88/0xbc
[<1016d284>] handle_IRQ_event+0x70/0x150
[<1016d4b0>] __do_IRQ+0x14c/0x1cc
[<10112efc>] do_cpu_irq_mask+0x9c/0xd0
[<10116068>] intr_return+0x0/0x4
This crash seems to happen due to an uninitialized variable "rc".
The compiler even warns about that:
CC drivers/ide/ide-cd.o
/mnt/sda4/home/cvs/parisc/git-kernel/linus-linux-2.6/drivers/ide/ide-cd.c: In function `cdrom_newpc_intr':
/mnt/sda4/home/cvs/parisc/git-kernel/linus-linux-2.6/drivers/ide/ide-cd.c:612: warning: `rc' might be used uninitialized in this function
After applying the trivial patch below, which just initializes
the variable to zero, the kernel doesn't crash any longer:
Starting the hotplug events dispatcher: udevd.
Synthesizing the initial hotplug events...
hda: command error: status=0x51 { DriveReady SeekComplete Error }
hda: command error: error=0x54 <3>{ AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
done.
Signed-off-by: Helge Deller <deller@gmx.de>
Acked-by: Borislav Petkov <petkovbb@gmail.com>
Cc: Linus <torvalds@linux-foundation.org>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Fix UDMA throughput bug: tCYC averages t2CYCTYP/2, but the code
previously assumed it was the same as t2CYCTYP. (That is, it was
using just one clock edge, not both.) Move the table's type
declaration so it's adjacent to the table, making it more clear
what those numbers mean.
On one system this change increased throughput by almost 4x: UDMA/66
sometimes topped 23 MB/sec (on a drive known to do much better). On
another system it was around a 10% win (UDMA/66 up to 7+ MB/sec).
The difference might be caused by the ratio between memory and IDE
clocks. In the system with large speedup, this was exactly 2 (as a
workaround for a rev 1.1 silicon bug). The other system used a more
standard ratio of 1.63 (and rev 2.1 silicon) ... clock domain synch
might have some issues, they're not unheard-of.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Impact: drop unnecessary code
Now that everything uses bio and block operations, there is no need to
reset request fields manually when retrying a request. Every field is
guaranteed to be always valid. Drop unnecessary request field
resetting from ide_dma_timeout_retry().
Signed-off-by: Tejun Heo <tj@kernel.org>
Impact: remove code path which is no longer necessary
All IDE data transfers now use rq->bio. Simplify ide_map_sg()
accordingly.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Impact: remove fields and code paths which are no longer necessary
Now that ide-tape uses standard mechanisms to transfer data, special
case handling for bh handling can be dropped from ide-atapi. Drop the
followings.
* pc->cur_pos, b_count, bh and b_data
* drive->pc_update_buffers() and pc_io_buffers().
Signed-off-by: Tejun Heo <tj@kernel.org>
Impact: cleanup
idetape_chrdev_read/write() functions are unnecessarily complex when
everything can be handled in a single loop. Collapse
idetape_add_chrdev_read/write_request() into the rw functions and
simplify the implementation.
Signed-off-by: Tejun Heo <tj@kernel.org>
Impact: cleanup
Byte size is what most issue functions deal with, make
idetape_queue_rw_tail() and its wrappers take byte size instead of
sector counts. idetape_chrdev_read() and write() functions are
converted to use tape->buffer_size instead of ctl from tape->cap.
This cleans up code a little bit and will ease the next r/w
reimplementation.
Signed-off-by: Tejun Heo <tj@kernel.org>
Impact: kill now unnecessary idetape_bh
With everything using standard mechanisms, there is no need for
idetape_bh anymore. Kill it and use tape->buf, cur and valid to
describe data buffer instead.
Changes worth mentioning are...
* idetape_queue_rq_tail() now always queue tape->buf and and adjusts
buffer state properly before completion.
* idetape_pad_zeros() clears the buffer only once.
Signed-off-by: Tejun Heo <tj@kernel.org>
Impact: use standard way to transfer data
ide-tape uses rq in an interesting way. For r/w requests, rq->special
is used to carry a private buffer management structure idetape_bh and
rq->nr_sectors and current_nr_sectors are initialized to the number of
idetape blocks which isn't necessary 512 bytes. Also,
rq->current_nr_sectors is used to report back the residual count in
units of idetape blocks.
This peculiarity taxes both block layer and ide. ide-atapi has
different paths and hooks to accomodate it and what a rq means becomes
quite confusing and making changes at the block layer becomes quite
difficult and error-prone.
This patch makes ide-tape use bio instead. With the previous patch,
ide-tape currently is using single contiguos buffer so replacing it
isn't difficult. Data buffer is mapped into bio using
blk_rq_map_kern() in idetape_queue_rw_tail(). idetape_io_buffers()
and idetape_update_buffers() are dropped and pc->bh is set to null to
tell ide-atapi to use standard data transfer mechanism and idetape_bh
byte counts are updated by the issuer on completion using the residual
count.
This change also nicely removes the FIXME in ide_pc_intr() where
ide-tape rqs need to be completed using ide_rq_bytes() instead of
blk_rq_bytes() (although this didn't really matter as the request
didn't have bio).
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jens Axboe <jens.axboe@oracle.com>
Impact: simpler buffer allocation and handling, kills OOM, fix DMA transfers
ide-tape has its own multiple buffer mechanism using struct
idetape_bh. It allocates buffer with decreasing order-of-two
allocations so that it results in minimum number of segments.
However, the implementation is quite complex and works in a way that
no other block or ide driver works necessitating a lot of special case
handling.
The benefit this complex allocation scheme brings is questionable as
PIO or DMA the number of segments (16 maximum) doesn't make any
noticeable difference and it also doesn't negate the need for multiple
order allocation which can fail under memory pressure or high
fragmentation although it does lower the highest order necessary by
one when the buffer size isn't power of two.
As the first step to remove the custom buffer management, this patch
makes ide-tape allocate single continous buffer. The maximum order is
four. I doubt the change would cause any trouble but if it ever
matters, it should be converted to regular sg mechanism like everyone
else and even in that case dropping custom buffer handling and moving
to standard mechanism first make sense as an intermediate step.
This patch makes the first bh to contain the whole buffer and drops
multi bh handling code. Following patches will make further changes.
This patch has the side effect of killing OOM triggered by allocation
path and fixing DMA transfers. Previously, bug in alloc path
triggered OOM on command issue and commands were passed to DMA engine
without DMA-mapping all the segments.
Signed-off-by: Tejun Heo <tj@kernel.org>
Impact: allow residual count implementation in ->pc_callback()
rq->data_len has two duties - carrying the number of input bytes on
issue and carrying residual count back to the issuer on completion.
ide-atapi completion callback ->pc_callback() is the right place to do
this but currently ide-atapi depends on rq->data_len carrying the
original request size after calling ->pc_callback() to complete the pc
request.
This patch makes ide_pc_intr(), ide_tape_issue_pc() and
ide_floppy_issue_pc() cache length to complete before calling
->pc_callback() so that it can modify rq->data_len as necessary.
Note: As using rq->data_len for two purposes can make cases like this
incorrect in subtle ways, future changes will introduce separate
field for residual count.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jens Axboe <jens.axboe@oracle.com>
Impact: fix infinite retry loop
After a command failed, ide-tape and floppy inserts REQUEST_SENSE in
front of the failed command and according to the result, sets
pc->retries, flags and errors. After REQUEST_SENSE is complete, the
failed command is again at the front of the queue and if the verdict
was to terminate the request, the issue functions tries to complete it
directly by calling drive->pc_callback() and returning ide_stopped.
However, drive->pc_callback() doesn't complete a request. It only
prepares for completion of the request. As a result, this creates an
infinite loop where the failed request is retried perpetually.
Fix it by actually ending the request by calling ide_complete_rq().
Signed-off-by: Tejun Heo <tj@kernel.org>
Impact: cleanup rq->data usage
ide-pm uses rq->data to carry pointer to struct request_pm_state
through request queue and rq->special is used to carray pointer to
local struct ide_cmd, which isn't necessary. Use rq->special for
request_pm_state instead and use local ide_cmd in
ide_start_power_step().
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Impact: unify request data buffer handling
rq->data is used mostly to pass kernel buffer through request queue
without using bio. There are only a couple of places which still do
this in kernel and converting to bio isn't difficult.
This patch converts ide-cd and atapi to use bio instead of rq->data
for request sense and internal pc commands. With previous change to
unify sense request handling, this is relatively easily achieved by
adding blk_rq_map_kern() during sense_rq prep and PC issue.
If blk_rq_map_kern() fails for sense, the error is deferred till sense
issue and aborts the failed command which triggered the sense. Note
that this is a slim possibility as sense prep is done on each command
issue, so for the above condition to actually trigger, all preps since
the last sense issue till the issue of the request which would require
a sense should fail.
* do_request functions might sleep now. This should be okay as ide
request_fn - do_ide_request() - is invoked only from make_request
and plug work. Make sure this is the case by adding might_sleep()
to do_ide_request().
* Functions which access the read sense data before the sense request
is complete now should access bio_data(sense_rq->bio) as the sense
buffer might have been copied during blk_rq_map_kern().
* ide-tape updated to map sg.
* cdrom_do_block_pc() now doesn't have to deal with REQ_TYPE_ATA_PC
special case. Simplified.
* tp_ops->output/input_data path dropped from ide_pc_intr().
Signed-off-by: Tejun Heo <tj@kernel.org>
Since we're issuing REQ_TYPE_SENSE now we need to allow those types of
rqs in the ->do_request callbacks. As a future improvement, sense_len
assignment might be unified across all ATAPI devices. Borislav to
check with specs and test.
As a result, get rid of ide_queue_pc_head() and
drive->request_sense_rq.
tj: * Init request sense ide_atapi_pc from sense request. In the
longer timer, it would probably better to fold
ide_create_request_sense_cmd() into its only current user -
ide_floppy_get_format_progress().
* ide_retry_pc() no longer takes @disk.
CC: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
CC: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Preallocate a sense request in the ->do_request method and reinitialize
it only on demand, in case it's been consumed in the IRQ handler path.
The reason for this is that we don't want to be mapping rq to bio in
the IRQ path and introduce all kinds of unnecessary hacks to the block
layer.
tj: * Both user and kernel PC requests expect sense data to be stored
in separate storage other than drive->sense_data. Copy sense
data to rq->sense on completion if rq->sense is not NULL. This
fixes bogus sense data on PC requests.
As a result, remove cdrom_queue_request_sense.
CC: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
CC: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This is in preparation of removing the queueing of a sense request out
of the IRQ handler path.
Use struct request_sense as a general sense buffer for all ATAPI
devices ide-{floppy,tape,cd}.
tj: * blk_get_request(__GFP_WAIT) can't be called from do_request() as
it can cause deadlock. Converted to use inline struct request
and blk_rq_init().
* Added xfer / cdb len selection depending on device type.
* All sense prep logics folded into ide_prep_sense() which never
fails.
* hwif->rq clearing and sense_rq used handling moved into
ide_queue_sense_rq().
* blk_rq_map_kern() conversion is moved to later patch.
CC: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
CC: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Impact: rq->buffer usage cleanup
ide-cd uses rq->buffer to carry pointer to the original request when
issuing REQUEST_SENSE. Use rq->special instead.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Impact: rq->buffer usage cleanup
ide-atapi uses rq->buffer as private opaque value for internal special
requests. rq->special isn't used for these cases (the only case where
rq->special is used is for ide-tape rw requests). Use rq->special
instead.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Impact: rq->buffer usage cleanup
ide_raw_taskfile() directly uses rq->buffer to carry pointer to the
data buffer. This complicates both block interface and ide backend
request handling. Use blk_rq_map_kern() instead and drop special
handling for REQ_TYPE_ATA_TASKFILE from ide_map_sg().
Note that REQ_RW setting is moved upwards as blk_rq_map_kern() uses it
to initialize bio rw flag.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Impact: remove unnecessary code path
Block pc requests always use bio and rq->data is always NULL. No need
to worry about !rq->bio cases in idefloppy_block_pc_cmd(). Note that
ide-atapi uses ide_pio_bytes() for bio PIO transfer which handle sg
fine.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Impact: code simplification
ide_cd_request_sense_fixup() clears the tail of the sense buffer if
the device didn't completely fill it. This patch makes
cdrom_queue_request_sense() clear the sense buffer before issuing the
command instead of clearing it afterwards. This simplifies code and
eases future changes.
Signed-off-by: Tejun Heo <tj@kernel.org>
Impact: fix an oops which always triggers
ide_tape_issue_pc() assumed drive->pc isn't NULL on invocation when
checking for back-to-back request sense issues but drive->pc can be
NULL and even when it's not NULL, it's not safe to dereference it once
the previous command is complete because pc could have been freed or
was on stack. Kill back-to-back REQUEST_SENSE detection.
Signed-off-by: Tejun Heo <tj@kernel.org>
The driver somehow got merged with the initializer for the dma_sff_read_status()
method missing which caused kernel panic on bootup.
This should fix the kernel.org bug #13026...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Reported-by: Arnd Hannemann <hannemann@nets.rwth-aachen.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Freeing non-slab objects is bad and results in an oops. Fix it.
Reported-and-tested-by: Andrew Price <andy@andrewprice.me.uk>
Cc: Theodore Tso <tytso@mit.edu>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Remove uneeded void casts
Signed-off-by: Jack Stone <jwjstone@fastmail.fm>
Cc: jeff@garzik.org
Cc: kernel-janitors@vger.kernel.org
Cc: Jack Stone <jwjstone@fastmail.fm>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Use ATA_DMA_* constants instead of the bare numbers for the BMIDE register bits.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The big driver change in 2.4.19-rc1 introduced a regression for many HPT370[A]
chips -- DMA stopped to work completely, only causing endless timeouts...
The culprit has been identified (at last!): it turned to be the code resetting
the DMA state machine before each transfer. Stop doing it now as this counter-
measure has clearly caused more harm than good.
This should fix the kernel.org bug #7703.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
As we have already PIO 6 transfer mode supported in IDE layer, we can turn
it on in the driver.
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Tested-by: "Steve Wootton" <swootton@esi-estech.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Make the case of flushing the drive's cache explicit.
There should be no functional change resulting from this patch.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Simplify tf_read() method, making it deal only with 'struct ide_taskfile' and
the validity flags that the upper layer passes, and factoring out the code that
deals with the high order bytes into ide_tf_readback() to be called from the
only two functions interested, ide_complete_cmd() and ide_dump_sector().
This should stop the needless code duplication in this method and so make
it about twice smaller than it was; along with simplifying the setup for
the method call, this should save both time and space...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Simplify tf_load() method, making it deal only with 'struct ide_taskfile' and
the validity flags that the upper layer passes, and moving the code that deals
with the high order bytes into the only function interested, do_rw_taskfile().
This should stop the needless code duplication in this method and so make
it about twice smaller than it was; along with simplifying the setup for the
method call, this should save both time and space...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Use write_devctl() method to clear/set the HOB bit in tf_read() method.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Move device register masking (and setting drive->select) out of tf_load() method
and into the only function that needs to use this code, do_rw_taskfile()...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
[bart: fix whitespace error]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Make 'struct ide_taskfile' cover only 8 register values and thus put two such
fields ('tf' and 'hob') into 'struct ide_cmd', dropping unnecessary 'tf_array'
field from it.
This required changing the prototype of ide_get_lba_addr() and ide_tf_dump().
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
[bart: fix setting of ATA_LBA bit for LBA48 commands in __ide_do_rw_disk()]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Replace IDE_TFLAG_{IN|OUT}_* flags meaning to the taskfile register validity on
input/output by the IDE_VALID_* flags and introduce 4 symmetric 8-bit register
validity indicator subfields, 'valid.{input/output}.{tf|hob}', into the 'struct
ide_cmd' instead of using the 'tf_flags' field for that purpose (this field can
then be turned from 32-bit into 8-bit one).
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Based on earlier work by Borislav Petkov.
Fix intendation in cdrom_decode_status(), no real code changes.
While at it:
- beautify comments
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Based on earlier work by Borislav Petkov.
Unify handling of fs and pc requests in cdrom_decode_status().
While at it:
- remove unreachable code
The only change in functionality is that for pc requests more
detailed error message will be printed for following sense keys:
* ILLEGAL_REQUEST
* DATA_PROTECT
* MEDIUM_ERROR
* BLANK_CHECK
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Based on earlier work by Borislav Petkov.
Convert cdrom_decode_status() to use switch statements in
preparation to unify handling of fs and pc requests.
While at it:
- remove superfluous comments and do minor CodingStyle fixups
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There should be no functional change resulting from this patch.
Suggested-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Now tx493[89]ide_tf_{load,read} do not contain word I/O operations.
They are endian-free now.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>,
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There should be no functional change resulting from this patch.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There should be no functional change resulting from this patch.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Since tf_{read|load}() methods of this driver have now become identical to their
standard counterparts using I/O port accesses, there's no need to override those
anymore...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Since tf_{read|load}() methods of this driver have now become identical to their
standard counterparts using MMIO accesses, there's no need to override those
anymore...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Remove two no longer used functions that I've overlooked...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* define CHECK_DMA_MASK
* remove use of wmb()
Reported-by: Grant Grundler <grundler@google.com>
Reviewed-by: Grant Grundler <grundler@google.com>
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
This patch:
o replaces "mask" variable in ide_dma_end() with #define.
o removes use of wmb() in ide-dma-sff.c and scc_pata.c.
o is not tested - I don't have (or want) the HW.
Signed-off-by: Grant Grundler <grundler@google.com>
Cc: KOBAYASHI Yoshitake <yoshitake.kobayashi@toshiba.co.jp>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Both of commits f94116aeec ("ide: cleanup
<asm-m68k/ide.h>") and 15a453a955 ("ide: include
<asm/ide.h> only when needed") break falconide:
| Uniform Multi-Platform E-IDE driver
| ide: Falcon IDE controller
| Probing IDE interface ide0...
| hda: Sarge m68k, ATA DISK drive
| ide0 at 0xfff00000 on irq 15 (serialized)
| ide-gd driver 1.18
| hda: max request size: 128KiB
| hda: 2118816 sectors (1084 MB) w/256KiB Cache, CHS=2102/16/63
| hda:<4>hda: lost interrupt
This happens because falconide relies on {in,out}sw() being redefined in
<asm/ide.h>, as included by <linux/ide.h>, which is no longer the case.
Use __ide_mm_{in,out}sw() from <asm/ide.h> instead, just like
ide_{in,out}put_data() do.
The same problem seems to exist in q40ide.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
commit 255115fb35 ("ide: allow host drivers to
specify IRQ flags") added irq_flags fields to struct ide_port_info and struct
ide_host. Drivers can now set ide_port_info.irq_flags = IRQF_SHARED, while
init_irq() passes ide_host.irq_flags to request_irq().
Unfortunately ide_host.irq_flags is never set, causing (on ARAnyM):
| Uniform Multi-Platform E-IDE driver
| ide: Falcon IDE controller
| Probing IDE interface ide0...
| hda: Sarge m68k, ATA DISK drive
| init_irq: sa = 0
| ide0: disabled, unable to get IRQ 15
| ide0: failed to initialize IDE interface
| ide0: disabling port
Solve this by copying ide_port_info.irq_flags to ide_host.irq_flags in
ide_host_alloc().
This bug probably affects the following IDE host drivers:
- buddha
- delkin_cb
- falconide
- gayle
- ide-cs
- macide
- q40ide
- scc_pata
- sgiioc4
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Replace all DMA_32BIT_MASK macro with DMA_BIT_MASK(32)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
... and access them afterwards. Simplify rq completing code while at it.
Spotted-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
No reason to need IDE built-in to be able to compile pmac driver.
Tested to work on 2.6.29-rc8 and 2.6.28.8 with ide and pmac as modules
inside an initramfs.
Signed-off-by: Gilles Espinasse <g.esp@free.fr>
Cc: sam@ravnborg.org
Cc: benh@kernel.crashing.org
[bart: remove now superfluous IDE check]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
As IDE cable used on Apple PowerBook/iBook laptops are always of "Short 40"
type when the firmware says it's 80 conductor one, the cable detection should
return ATA_CBL_PATA40_SHORT on those machines. This enables to automatically
use UDMA5 even with drives that doesn't correctly detect those cables on Apple
laptops.
Signed-off-by: TOMARI Hisanobu <posco.grubb@gmail.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: benh@kernel.crashing.org
[bart: beautify patch description]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Since SELECT_DRIVE() has boiled down to a mere dev_select() method call, it now
makes sense to just inline it...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Turn selectproc() method into dev_select() method by teaching it to write to the
device register and moving it from 'struct ide_port_ops' to 'struct ide_tp_ops'.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: benh@kernel.crashing.org
Cc: petkovbb@gmail.com
[bart: add ->dev_select to at91_ide.c and tx4939.c (__BIG_ENDIAN case)]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Move IDE_FTFLAG_{IN|OUT}_DATA flag handling out of tf_{read|load}() methods
into the only two functions where these flags actually need to be handled:
do_rw_taskfile() and ide_complete_cmd()...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Handle IDE_FTFLAG_{IN|OUT}_DATA flags in tf_{read|load}() methods by calling
{in|out}put_data() methods to transfer 2 bytes -- this will allow us to move
that handling out of those methods altogether...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
ide_{in|out|put_data() can be somewhat shortened by merging the paths doing
16-bit I/O...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The feature register has never been readable -- when its location is read, one
gets the error register value; hence rename IDE_TFLAG_IN_[HOB_]FEATURE into
IDE_TFLAG_IN_[HOB_]ERROR and introduce the 'hob_error' field into the 'struct
ide_taskfile' (despite the error register not really depending on the HOB bit).
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Turn set_irq() method with its software reset hack into write_devctl() method
(for just writing a value into the device control register) at last...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Make use of ATA_HOB instead of hard-coded value in the tf_read() method.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Make use of ATA_ERR instead of hard-coded value in idedisk_set_max_address()
and idedisk_read_native_max_address().
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add support for the CompactFlash specific PIO modes 5/6 and MWDMA modes 3/4.
Since there were no PIO5 capable hard drives produced and one would also need
66 MHz IDE clock to actually get the difference WRT the address setup timings
programmed, I decided to simply replace the old non-standard PIO mode 5 timings
with the CFA specified ones.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: stf_xl@wp.pl
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The bytes indicating current DMA mode in the identify data words 62, 63, and 88
should only change on setting a DMA mode, so stop clearing them on setting PIO
mode in ide_config_drive_speed(). While at it, correct SW/MW DMA mode masks...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The IDE code assumed for years that the bit 1 of the identify data word 53 also
covers the validity of the SW/MW DMA information in words 62 and 63, but it has
always covered only words 64 thru 70, with words 62 and 63 being defined in the
original ATA spec, not in ATA-2...
This fix however should only concern *very* old hard disks and rather old CF
cards...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Make auide_{insw|outsw}() 'static' and mark them 'inline' as there's only one
call site for each: in the driver's {in|out}put_data() methods respectively...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Fix ide_init_sg_cmd() setup for non-fs requests.
* Convert ide_pc_intr() to use ide_pio_bytes() for floppy media.
* Remove no longer needed ide_io_buffers() and sg/sg_cnt fields
from struct ide_atapi_pc.
* Remove partial completions; kill idefloppy_update_buffers(), as a
result.
* Add some more debugging statements.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Return number of bytes left to transfer from idetape_{in,out}put_buffers()
and number of bytes done from ide_tape_io_buffers().
* Fix padding for PIO transfers in ide_pc_intr() so read/write buffers are
always completely processed and then the transfer is padded if necessary.
* Remove invalid error messages.
* Remove now superfluous padding from ide{_io_buffers,tape_input_buffers}().
While at it:
* Set pc->bh to NULL in idetape_input_buffers() after all bh-s are done.
* Cache !!(pc->flags & PC_FLAG_WRITING) in local variable in ide_pc_intr().
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Nowadays it is not worth having a separate config option for
Amiga IDE Doubler support so always include it (it still needs
to be explicitly enabled by module parameter).
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
struct ide_atapi_pc is often allocated on the stack and size of ->pc_buf
size is 256 bytes. However since only ide_floppy_create_read_capacity_cmd()
and idetape_create_inquiry_cmd() require such size allocate buffers for
these pc-s explicitely and decrease ->pc_buf size to 64 bytes.
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There is no need for a separate ide_arm host driver nowadays
so merge it into ide_generic one.
While at it:
- return -EBUSY from ide_generic_init() if I/O resources are busy
- scale down ide_generic_check_pci_legacy_iobases() for CONFIG_PCI=n
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Alexander Schulz <alex@shark-linux.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Nowadays we have "ide_generic.probe_mask=" module parameter
and ide_platform host driver so sysfs interface for adding
IDE interfaces is no longer needed.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Move ide_map_sg() calls out from ide_build_sglist()
to ide_dma_prepare().
* Pass command to ide_destroy_dmatable().
* Rename ide_build_sglist() to ide_dma_map_sg()
and ide_destroy_dmatable() to ide_dma_unmap_sg().
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Set/clear drive->waiting_for_dma flag in the core code
instead of in ->dma_setup and ->dma_end methods.
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Move ide_map_sg() call from ->dma_setup implementations and
ide_destroy_dmatable() one from *_build_dmatable() to ide_dma_prepare().
There should be no functional changes caused by this patch.
Sergei:
Removed 'use_pio_instead' labels and replaced 'goto' with 'return 0' --
that required no changes to the follow-up patches...
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add (an optional) ->dma_check method for checking if DMA can be
used for a given command and fail DMA setup in ide_dma_prepare()
if necessary.
* Convert alim15x3 and trm290 host drivers to use ->dma_check.
* Rename ali15x3_dma_setup() to ali_dma_check() while at it.
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Use custom ->dma_{start,end} methods to handle trm290_prepare_drive()
there instead of in ->dma_setup method.
There should be no functional changes caused by this patch
(DMA support is disabled currently in trm290.c).
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Use custom ->dma_{start,end} methods to handle ns87415_prepare_drive()
there instead of in ->dma_setup method.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add ide_dma_prepare() helper.
* Convert ide_issue_pc() and do_rw_taskfile() to use it.
* Make ide_build_sglist() static.
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Since ide_dma_timeout() is only used by ide_dma_timeout_retry()
inline it there.
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
All custom ->dma_timeout implementations call the generic one thus it is
possible to have only an optional method for resetting DMA engine instead:
* Add ->dma_clear method and convert hpt366, pdc202xx_old and sl82c105
host drivers to use it.
* Always use ide_dma_timeout() in ide_dma_timeout_retry() and remove
->dma_timeout method.
* Make ide_dma_timeout() static.
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cache drive->queue in local variable and use max().
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Acked-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* 'thislen' is always <= cmd->nleft for non-fs requests so the transfer
padding inside the 'while (thislen > 0)' loop can happen only for fs
requests -- then move it out of the loop and unify with the transfer
padding for non-fs requests ('thislen' == 'len' for fs requests).
* blk_dump_rq_flags() dumps all request flags so it is enough to pass
only the function name to it.
* Update my Copyrights while at it.
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Use the following facts:
- rq->nr_sectors should now be always equal to (non-zero)
rq->hard_nr_sectors for fs requests
- REQ_TYPE_ATA_PC requests have never bio attached to them
- rq->hard_nr_sectors == 0 for REQ_TYPE_ATA_PC requests
- DMA is used only for fs, pc and REQ_TYPE_ATA_PC requests
- 'uptodate' is ignored for pc requests ('rc == 0' case)
and use the common completion path also for DMA requests.
There should be no functional changes caused by this patch
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Convert ide-cd to use scatterlists for PIO transfers and get rid of
partial completions (except on error) also for non-fs requests.
v2:
Do not map dataless commands to an sg since it oopses on the virt_to_page()
translation check when DEBUG_VIRTUAL is enabled. (from Borislav Petkov,
reported/bisected-by Tetsuo Handa).
Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Acked-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There should be no functional changes caused by this patch.
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
We now support arbitrary number of bytes per-IRQ also for fs requests
so remove ide_cd_check_transfer_size() and IDE_AFLAG_LIMIT_NFRAMES.
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Export ide_pio_bytes().
* Add ->last_xfer_len field to struct ide_cmd.
* Add ide_cd_error_cmd() helper to ide-cd.
* Convert ide-cd to use scatterlists also for PIO transfers (fs requests
only for now) and get rid of partial completions (except when the error
happens -- which is still subject to change later because looking at
ATAPI spec it seems that the device is free to error the whole transfer
with setting the Error bit only on the last transfer chunk).
* Update ide_cd_{prepare_rw,restore_request,do_request}() accordingly.
* Inline ide_cd_restore_request() into cdrom_start_rw().
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There should be no functional changes caused by this patch.
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Inline cdrom_end_request() into cdrom_newpc_intr()
and ide_cd_do_request().
There should be no functional changes caused by this patch.
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Move cdrom_end_request() calls from cdrom_decode_status()
and ide_cd_check_ireason() to cdrom_newpc_intr().
* Unify cdrom_newpc_intr() exit paths.
There should be no functional changes caused by this patch.
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Move setting REQ_FAILED flag out from 'end_request' exit path in
cdrom_newpc_intr() and also rename 'end_request' to 'out_end'.
There should be no functional changes caused by this patch.
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Move cdrom_end_request() calls from cdrom_start_rw()
and ide_cd_prepare_rw_request() to ide_cd_do_request().
* Unify ide_cd_do_request() exit paths.
There should be no functional changes caused by this patch.
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Borislav Petkov
Tejun Heo
Anton Vorontsov
Bartlomiej Zolnierkiewicz
Borislav Petkov
David Brownell
Bruno Prémont
Helge Deller
Sergei Shtylyov
Jack Stone
Stanislaw Gruszka
Huang Weiyi
Atsushi Nemoto
Grant Grundler
Geert Uytterhoeven
Yang Hongyang
Gilles Espinasse
TOMARI Hisanobu