These have the Mainpine PCI identifier on however
Additional paranoia check for Tornado versions added by Alan Cox
(and this time I remembered to do an stg refresh so that the corrections ended
up in these patches not randomly attached to another diff -- Alan)
Signed-off-by: Lee Howard <lee.howard@mainpine.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for the OxSemi 'Tornado' devices.
Reformatted and reworked a bit by Alan Cox
Signed-off-by: Lee Howard <lee.howard@mainpine.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
<rmk> talking about leaks - I noticed that the 'check return of
pci_enable_dev()' in the 8250 pci resume function finally made it in
despite my objections against it (causing stuff in higher levels to
leak).
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It is a no-name PCI card. I found no reference to a producer so I used
"UNKNOWN_0x1584" as the name.
Full lspci:
01:07.0 0780: 10b5:9050 (rev 01)
Subsystem: 10b5:1584
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- \
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- \
DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 10
Region 1: I/O ports at ec00 [size=128]
Region 2: I/O ports at e480 [size=32]
Region 3: I/O ports at e400 [size=8]
Capabilities: [40] Power Management version 1
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA \
PME(D0+,D1-,D2-,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [48] #06 [0080]
Capabilities: [4c] Vital Product Data
After:
0000:01:07.0: ttyS4 at I/O 0xe480 (irq = 10) is a 16550A
0000:01:07.0: ttyS5 at I/O 0xe488 (irq = 10) is a 16550A
0000:01:07.0: ttyS6 at I/O 0xe490 (irq = 10) is a 16550A
0000:01:07.0: ttyS7 at I/O 0xe498 (irq = 10) is a 16550A
Signed-off-by: Catalin(ux) M BOIE <catab@embedromix.ro>
Acked-by: Alan Cox <alan@redhat.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch removes CVS keywords that weren't updated for a long time in
comments, printk's and MODULE_DESCRIPTION's (no printk's or
MODULE_DESCRIPTION's are completely removed).
While doing this I also found and fixed a missing \n in a printk
in m32r_sio.c
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for the InstaShield IS-400 four port RS-232 PCI card.
Signed-off-by: Ignacio García Pérez <iggarpe@t2i.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix following warnings:
WARNING: drivers/serial/built-in.o(.data+0x5b8): Section mismatch in reference from the variable pci_serial_quirks to the function .devexit.text:pci_ite887x_exit()
WARNING: drivers/serial/built-in.o(.data+0x5e0): Section mismatch in reference from the variable pci_serial_quirks to the function .devexit.text:pci_plx9050_exit()
WARNING: drivers/serial/built-in.o(.data+0x608): Section mismatch in reference from the variable pci_serial_quirks to the function .devexit.text:pci_plx9050_exit()
WARNING: drivers/serial/built-in.o(.data+0x658): Section mismatch in reference from the variable pci_serial_quirks to the function .devexit.text:pci_plx9050_exit()
WARNING: drivers/serial/built-in.o(.data+0x680): Section mismatch in reference from the variable pci_serial_quirks to the function .devexit.text:pci_plx9050_exit()
WARNING: drivers/serial/built-in.o(.data+0x6a8): Section mismatch in reference from the variable pci_serial_quirks to the function .devexit.text:pci_plx9050_exit()
WARNING: drivers/serial/built-in.o(.data+0x6d0): Section mismatch in reference from the variable pci_serial_quirks to the function .devexit.text:sbs_exit()
WARNING: drivers/serial/built-in.o(.data+0x6f8): Section mismatch in reference from the variable pci_serial_quirks to the function .devexit.text:sbs_exit()
WARNING: drivers/serial/built-in.o(.data+0x720): Section mismatch in reference from the variable pci_serial_quirks to the function .devexit.text:sbs_exit()
WARNING: drivers/serial/built-in.o(.data+0x748): Section mismatch in reference from the variable pci_serial_quirks to the function .devexit.text:sbs_exit()
pci_serial_quirks contains a number of function pointers where the referenced
function is annotated __devexit. This is OK so we annotate pci_serial_quirks
with __refdata to ignore the __devexit references
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for a whole range of boards. Some are partly autodetected but
not fully correctly others (PCI Express notably) not at all. Stick all
the right entries in.
Thanks to Mainpine for information and testing.
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add PCI IDs for the onchip UARTs on PA Semi PWRficient.
Signed-off-by: Olof Johansson <olof@lixom.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The serial_pci driver tries to guess serial ports on unknown devices based
on the PCI class (modem or serial). On certain softmodems (AC'97 modems)
this can lead to the recognition of non-existing serial ports.
This patch adds a blacklist of PCI IDs that are to be ignored by the driver.
[akpm@linux-foundation.org: cleanups]
Signed-off-by: Christian Schmidt <schmidt@digadd.de>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Russell King <rmk+lkml@arm.linux.org.uk>
Cc: Yinghai Lu <yinghai.lu@sun.com>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for the it887x-chips (PCI) manufactured by ITE.
Signed-off-by: Niels de Vos <niels.devos@wincor-nixdorf.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
After Al Viro (finally) succeeded in removing the sched.h #include in module.h
recently, it makes sense again to remove other superfluous sched.h includes.
There are quite a lot of files which include it but don't actually need
anything defined in there. Presumably these includes were once needed for
macros that used to live in sched.h, but moved to other header files in the
course of cleaning it up.
To ease the pain, this time I did not fiddle with any header files and only
removed #includes from .c-files, which tend to cause less trouble.
Compile tested against 2.6.20-rc2 and 2.6.20-rc2-mm2 (with offsets) on alpha,
arm, i386, ia64, mips, powerpc, and x86_64 with allnoconfig, defconfig,
allmodconfig, and allyesconfig as well as a few randconfigs on x86_64 and all
configs in arch/arm/configs on arm. I also checked that no new warnings were
introduced by the patch (actually, some warnings are removed that were emitted
by unnecessarily included header files).
Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for the CPCI-ASIO4 quad port CompactPCI UART board from
electronic system design gmbh.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Get the Perle quad-modem PCI card (PCI-RAS4) detected by serial driver. It
may also get the PCI-RAS8 running, but can't guarantee as I didn't had one for
testing.
Signed-off-by: Thomas Hoehn <thomas.hoehn@avocent.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds initial support to 8250-pci for the Korenix Jetcard PCI serial
cards. The JC12xx cards are standard RS232-based serial cards utilising
the Oxford 16C950 device.
The JC14xx are RS422/RS485-based cards, but in order for these to be
supported natively, we will need additional tweaks to the 8250 layers so
we can specify some values for the 950's registers. Hence, these two
entries are commented out.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove some code which is unneeded if CONFIG_PM=n.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
- some const- ification and usage of ARRAY_SIZE() in serial drivers
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Here is a patch that adds support for the Instashield IS-200 2 port PCI
serial card.
Signed-off-by: Peter Horton <pdh@colonel-panic.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-serial:
[SERIAL] Ensure 8250_pci quirks are not marked __devinit
[SERIAL] Convert fifosize to an unsigned int
The 8250_pci quirks must not be marked __devinit since they may
be used from parport_serial. We only really need to mark those
which might be used by cards recognised by parport_serial, but
that wouldn't allow static checking.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Based on a patch series originally from Vivek Goyal <vgoyal@in.ibm.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds new PCI serial card support.
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds support for SIIG 8-port boards. These boards have 4 ports in
separate bars and another 4 ports in the single bar. Because of this strange
port arrangement these cards need special setup function. Fortunately no other
SIIG cards have more than 4 port, so this setup function could be used for them
too.
Signed-off-by: Andrey Panin <pazke@donpac.ru>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There is a new device which is look like:
Serial controller: Decision Computer International Co. PCCOM2 (rev 02) (prog-if 02 [16550])
0700: 6666:0004 (rev 02) (prog-if 02)
Flags: medium devsel, IRQ 177
Memory at fe000000 (32-bit, non-prefetchable) [size=128]
I/O ports at e880 [size=128]
I/O ports at e400 [size=256]
It has two 16550A, and is not listed in kernel, although the
manufacturer clams that it is supported...
I've created the following patch, it only add the new PCI id and the
card to the repository, it seems to work.
Signed-off-by: Alon Bar-Lev <alon.barlev@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
I've also fixed the sort-ordering comments on this naming convention.
Signed-off-by: Stuart MacDonald <stuartm@connecttech.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch marks a few serial data structures const, moving them to
.rodata where they won't false-share cachelines with things that get
written to.
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add the new ID 0x132a and configure the new PCI Diva console port. This
device supports only 1 single console UART.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested by Wolfgang Denk with this device:
00:0f.0 Network controller: PLX Technology, Inc. PCI <-> IOBus Bridge (rev 01)
Subsystem: Exsys EX-4055 4S(16C550) RS-232
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 10
Region 0: Memory at 80100000 (32-bit, non-prefetchable) [size=128]
Region 1: I/O ports at 7080 [size=128]
Region 2: I/O ports at 7400 [size=32]
00:0f.0 Class 0280: 10b5:9050 (rev 01)
Subsystem: d84d:4055
Results with this patch:
Serial: 8250/16550 driver $Revision: 1.90 $ 32 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
PCI: Found IRQ 10 for device 0000:00:0f.0
ttyS4 at I/O 0x7400 (irq = 10) is a 16550A
ttyS5 at I/O 0x7408 (irq = 10) is a 16550A
ttyS6 at I/O 0x7410 (irq = 10) is a 16550A
ttyS7 at I/O 0x7418 (irq = 10) is a 16550A
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for the MRi PCIDS1 dual port serial card. This card is a
little controversial since it is the subject of a PCI vendor/device ID
clash. (See
http://www.ussg.iu.edu/hypermail/linux/kernel/0303.1/0516.html). I have
for now just used the hex ID 0x950a. The divisor was part calculated part
iterated, so may not be exactly correct (but works for me at all settings
between 300 - 115300 bps).
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Convert parport_serial to use the new 8250_pci interface, converting
the table to a pciserial_board table. This also unuses the SPCI_*
definitions in serialP.h, which can now be removed.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Re-jig the setup/removal/suspend/resume of 8250 pci ports so that they
know slightly less about how they're attached to a PCI device. Expose
this as the new interface for registering PCI serial ports, as well as
the pciserial_board structure and associated flag definitions.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Pass the serial_private structure via the setup method instead of
the pci_dev. We don't want to assume that the pci_dev's driver
data is a pointer to serial_private. Instead, put the pci_dev
inside serial_private.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Collapse all the SIIG quirk entries into one. SIIG10x cards all
have PCI device IDs of 0x10xx, SIIG20x cards all have PCI device
IDs of 0x20xx.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for SIIG Quartet Serial card. This card has Oxford
Semiconducor 16954 quad UART which is clocked by 10x faster
(18.432 MHz) quartz.
Signed-off-by: Andrey Panin <pazke@donpac.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
Lee Howard
Alan Cox
Catalin(ux) M BOIE
Adrian Bunk
Ignacio García Pérez
Alan Cox
Sam Ravnborg
Al Viro
Krauth.Julien
Dirk Hohndel
Ralf Baechle
Olof Johansson
Christian Schmidt
Niels de Vos
Yoichi Yuasa
Tim Schmielau
Burman Yan
Matthias Fuchs
Thomas Hoehn
Russell King
Alexey Dobriyan
Helge Deller
Peter Horton
Linus Torvalds
Russell King
Greg Kroah-Hartman
Andrey Panin
Alon Bar-Lev
Andrew Morton
Gareth Howlett
Dave Jones
Arjan van de Ven
Justin Chen
Bjorn Helgaas
David Ranson
Linus Torvalds