Pull networking fixes from Jakub Kicinski:
- fix failure to add bond interfaces to a bridge, the offload-handling
code was too defensive there and recent refactoring unearthed that.
Users complained (Ido)
- fix unnecessarily reflecting ECN bits within TOS values / QoS marking
in TCP ACK and reset packets (Wei)
- fix a deadlock with bpf iterator. Hopefully we're in the clear on
this front now... (Yonghong)
- BPF fix for clobbering r2 in bpf_gen_ld_abs (Daniel)
- fix AQL on mt76 devices with FW rate control and add a couple of AQL
issues in mac80211 code (Felix)
- fix authentication issue with mwifiex (Maximilian)
- WiFi connectivity fix: revert IGTK support in ti/wlcore (Mauro)
- fix exception handling for multipath routes via same device (David
Ahern)
- revert back to a BH spin lock flavor for nsid_lock: there are paths
which do require the BH context protection (Taehee)
- fix interrupt / queue / NAPI handling in the lantiq driver (Hauke)
- fix ife module load deadlock (Cong)
- make an adjustment to netlink reply message type for code added in
this release (the sole change touching uAPI here) (Michal)
- a number of fixes for small NXP and Microchip switches (Vladimir)
[ Pull request acked by David: "you can expect more of this in the
future as I try to delegate more things to Jakub" ]
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (167 commits)
net: mscc: ocelot: fix some key offsets for IP4_TCP_UDP VCAP IS2 entries
net: dsa: seville: fix some key offsets for IP4_TCP_UDP VCAP IS2 entries
net: dsa: felix: fix some key offsets for IP4_TCP_UDP VCAP IS2 entries
inet_diag: validate INET_DIAG_REQ_PROTOCOL attribute
net: bridge: br_vlan_get_pvid_rcu() should dereference the VLAN group under RCU
net: Update MAINTAINERS for MediaTek switch driver
net/mlx5e: mlx5e_fec_in_caps() returns a boolean
net/mlx5e: kTLS, Avoid kzalloc(GFP_KERNEL) under spinlock
net/mlx5e: kTLS, Fix leak on resync error flow
net/mlx5e: kTLS, Add missing dma_unmap in RX resync
net/mlx5e: kTLS, Fix napi sync and possible use-after-free
net/mlx5e: TLS, Do not expose FPGA TLS counter if not supported
net/mlx5e: Fix using wrong stats_grps in mlx5e_update_ndo_stats()
net/mlx5e: Fix multicast counter not up-to-date in "ip -s"
net/mlx5e: Fix endianness when calculating pedit mask first bit
net/mlx5e: Enable adding peer miss rules only if merged eswitch is supported
net/mlx5e: CT: Fix freeing ct_label mapping
net/mlx5e: Fix memory leak of tunnel info when rule under multipath not ready
net/mlx5e: Use synchronize_rcu to sync with NAPI
net/mlx5e: Use RCU to protect rq->xdp_prog
...
When calling the RCU brother of br_vlan_get_pvid(), lockdep warns:
=============================
WARNING: suspicious RCU usage
5.9.0-rc3-01631-g13c17acb8e38-dirty #814 Not tainted
-----------------------------
net/bridge/br_private.h:1054 suspicious rcu_dereference_protected() usage!
Call trace:
lockdep_rcu_suspicious+0xd4/0xf8
__br_vlan_get_pvid+0xc0/0x100
br_vlan_get_pvid_rcu+0x78/0x108
The warning is because br_vlan_get_pvid_rcu() calls nbp_vlan_group()
which calls rtnl_dereference() instead of rcu_dereference(). In turn,
rtnl_dereference() calls rcu_dereference_protected() which assumes
operation under an RCU write-side critical section, which obviously is
not the case here. So, when the incorrect primitive is used to access
the RCU-protected VLAN group pointer, READ_ONCE() is not used, which may
cause various unexpected problems.
I'm sad to say that br_vlan_get_pvid() and br_vlan_get_pvid_rcu() cannot
share the same implementation. So fix the bug by splitting the 2
functions, and making br_vlan_get_pvid_rcu() retrieve the VLAN groups
under proper locking annotations.
Fixes: 7582f5b70f ("bridge: add br_vlan_get_pvid_rcu()")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* fix using HE on 2.4 GHz
* AQL (airtime queue limit) estimation & VHT160 fix
* do not oversize A-MPDUs if local capability is smaller than peer's
* fix radiotap on 6 GHz to not put 2.4 GHz flag
* fix Kconfig for lib80211
* little fixlet for 6 GHz channel number / frequency conversion
-----BEGIN PGP SIGNATURE-----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=ZjBk
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-net-2020-09-21' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Just a few fixes:
* fix using HE on 2.4 GHz
* AQL (airtime queue limit) estimation & VHT160 fix
* do not oversize A-MPDUs if local capability is smaller than peer's
* fix radiotap on 6 GHz to not put 2.4 GHz flag
* fix Kconfig for lib80211
* little fixlet for 6 GHz channel number / frequency conversion
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace a comma between expression statements by a semicolon.
Signed-off-by: Xu Wang <vulab@iscas.ac.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
When calculating ancestor_size with IPv6 enabled, simply using
sizeof(struct ipv6_pinfo) doesn't account for extra bytes needed for
alignment in the struct sctp6_sock. On x86, there aren't any extra
bytes, but on ARM the ipv6_pinfo structure is aligned on an 8-byte
boundary so there were 4 pad bytes that were omitted from the
ancestor_size calculation. This would lead to corruption of the
pd_lobby pointers, causing an oops when trying to free the sctp
structure on socket close.
Fixes: 636d25d557 ("sctp: not copy sctp_sock pd_lobby in sctp_copy_descendant")
Signed-off-by: Henry Ptasinski <hptasinski@google.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When IPV6_SEG6_HMAC is enabled and CRYPTO is disabled, it results in the
following Kbuild warning:
WARNING: unmet direct dependencies detected for CRYPTO_HMAC
Depends on [n]: CRYPTO [=n]
Selected by [y]:
- IPV6_SEG6_HMAC [=y] && NET [=y] && INET [=y] && IPV6 [=y]
WARNING: unmet direct dependencies detected for CRYPTO_SHA1
Depends on [n]: CRYPTO [=n]
Selected by [y]:
- IPV6_SEG6_HMAC [=y] && NET [=y] && INET [=y] && IPV6 [=y]
WARNING: unmet direct dependencies detected for CRYPTO_SHA256
Depends on [n]: CRYPTO [=n]
Selected by [y]:
- IPV6_SEG6_HMAC [=y] && NET [=y] && INET [=y] && IPV6 [=y]
The reason is that IPV6_SEG6_HMAC selects CRYPTO_HMAC, CRYPTO_SHA1, and
CRYPTO_SHA256 without depending on or selecting CRYPTO while those configs
are subordinate to CRYPTO.
Honor the kconfig menu hierarchy to remove kconfig dependency warnings.
Fixes: bf355b8d2c ("ipv6: sr: add core files for SR HMAC support")
Signed-off-by: Necip Fazil Yildiran <fazilyildiran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- fix wrong type use in backbone_gw hash, by Linus Luessing
- disable TT re-routing for multicast packets, by Linus Luessing
- Add missing include for in_interrupt(), by Sven Eckelmann
- fix BLA/multicast issues for packets sent via unicast,
by Linus Luessing (3 patches)
-----BEGIN PGP SIGNATURE-----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=JjK9
-----END PGP SIGNATURE-----
Merge tag 'batadv-net-for-davem-20200918' of git://git.open-mesh.org/linux-merge
Simon Wunderlich says:
====================
Here are some batman-adv bugfixes:
- fix wrong type use in backbone_gw hash, by Linus Luessing
- disable TT re-routing for multicast packets, by Linus Luessing
- Add missing include for in_interrupt(), by Sven Eckelmann
- fix BLA/multicast issues for packets sent via unicast,
by Linus Luessing (3 patches)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The ocelot_port->ts_id is used to:
(a) populate skb->cb[0] for matching the TX timestamp in the PTP IRQ
with an skb.
(b) populate the REW_OP from the injection header of the ongoing skb.
Only then is ocelot_port->ts_id incremented.
This is a problem because, at least theoretically, another timestampable
skb might use the same ocelot_port->ts_id before that is incremented.
Normally all transmit calls are serialized by the netdev transmit
spinlock, but in this case, ocelot_port_add_txtstamp_skb() is also
called by DSA, which has started declaring the NETIF_F_LLTX feature
since commit 2b86cb8299 ("net: dsa: declare lockless TX feature for
slave ports"). So the logic of using and incrementing the timestamp id
should be atomic per port.
The solution is to use the global ocelot_port->ts_id only while
protected by the associated ocelot_port->ts_id_lock. That's where we
populate skb->cb[0]. Note that for ocelot, ocelot_port_add_txtstamp_skb
is called for the actual skb, but for felix, it is called for the skb's
clone. That is something which will also be changed in the future.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When trying to associate to an AP support 180 or 80+80 MHz on 6 GHz with a
STA that only has 80 Mhz support the cf2 field inside the chandef will get
set causing the association to fail when trying to validate the chandef.
Fix this by checking the support flags prior to setting cf2.
Fixes: 57fa5e85d5 ("mac80211: determine chandef from HE 6 GHz operation")
Signed-off-by: John Crispin <john@phrozen.org>
Link: https://lore.kernel.org/r/20200918115304.1135693-1-john@phrozen.org
[reword commit message a bit]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When LIB80211_CRYPT_CCMP is enabled and CRYPTO is disabled, it results in unmet
direct dependencies config warning. The reason is that LIB80211_CRYPT_CCMP
selects CRYPTO_AES and CRYPTO_CCM, which are subordinate to CRYPTO. This is
reproducible with CRYPTO disabled and R8188EU enabled, where R8188EU selects
LIB80211_CRYPT_CCMP but does not select or depend on CRYPTO.
Honor the kconfig menu hierarchy to remove kconfig dependency warnings.
Fixes: a11e2f8548 ("lib80211: use crypto API ccm(aes) transform for CCMP processing")
Signed-off-by: Necip Fazil Yildiran <fazilyildiran@gmail.com>
Link: https://lore.kernel.org/r/20200909095452.3080-1-fazilyildiran@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When converting from struct ieee80211_tx_rate to ieee80211_rx_status,
there was one check missing to fill in the bandwidth for 160 MHz
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/r/20200915085945.3782-2-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The unit of the return value of ieee80211_get_rate_duration is nanoseconds, not
microseconds. Adjust the duration checks to account for that.
For higher data rates, allow larger estimated aggregation sizes, and add some
values for HE as well, which can use much larger aggregates.
Since small packets with high data rates can now lead to duration values too
small for info->tx_time_est, return a minimum of 4us.
Fixes: f01cfbaf9b ("mac80211: improve AQL aggregation estimation for low data rates")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/r/20200915085945.3782-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Tunnel offload info code uses ETHTOOL_MSG_TUNNEL_INFO_GET message type (cmd
field in genetlink header) for replies to tunnel info netlink request, i.e.
the same value as the request have. This is a problem because we are using
two separate enums for userspace to kernel and kernel to userspace message
types so that this ETHTOOL_MSG_TUNNEL_INFO_GET (28) collides with
ETHTOOL_MSG_CABLE_TEST_TDR_NTF which is what message type 28 means for
kernel to userspace messages.
As the tunnel info request reached mainline in 5.9 merge window, we should
still be able to fix the reply message type without breaking backward
compatibility.
Fixes: c7d759eb7b ("ethtool: add tunnel info interface")
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexei Starovoitov says:
====================
pull-request: bpf 2020-09-15
The following pull-request contains BPF updates for your *net* tree.
We've added 12 non-merge commits during the last 19 day(s) which contain
a total of 10 files changed, 47 insertions(+), 38 deletions(-).
The main changes are:
1) docs/bpf fixes, from Andrii.
2) ld_abs fix, from Daniel.
3) socket casting helpers fix, from Martin.
4) hash iterator fixes, from Yonghong.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The bpf_skc_to_* type casting helpers are available to
BPF_PROG_TYPE_TRACING. The traced PTR_TO_BTF_ID may be NULL.
For example, the skb->sk may be NULL. Thus, these casting helpers
need to check "!sk" also and this patch fixes them.
Fixes: 0d4fad3e57 ("bpf: Add bpf_skc_to_udp6_sock() helper")
Fixes: 478cfbdf5f ("bpf: Add bpf_skc_to_{tcp, tcp_timewait, tcp_request}_sock() helpers")
Fixes: af7ec13833 ("bpf: Add bpf_skc_to_tcp6_sock() helper")
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Yonghong Song <yhs@fb.com>
Acked-by: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/bpf/20200915182959.241101-1-kafai@fb.com
Kfir reported that pmtu exceptions are not created properly for
deployments where multipath routes use the same device.
After some digging I see 2 compounding problems:
1. ip_route_output_key_hash_rcu is updating the flowi4_oif *after*
the route lookup. This is the second use case where this has
been a problem (the first is related to use of vti devices with
VRF). I can not find any reason for the oif to be changed after the
lookup; the code goes back to the start of git. It does not seem
logical so remove it.
2. fib_lookups for exceptions do not call fib_select_path to handle
multipath route selection based on the hash.
The end result is that the fib_lookup used to add the exception
always creates it based using the first leg of the route.
An example topology showing the problem:
| host1
+------+
| eth0 | .209
+------+
|
+------+
switch | br0 |
+------+
|
+---------+---------+
| host2 | host3
+------+ +------+
| eth0 | .250 | eth0 | 192.168.252.252
+------+ +------+
+-----+ +-----+
| vti | .2 | vti | 192.168.247.3
+-----+ +-----+
\ /
=================================
tunnels
192.168.247.1/24
for h in host1 host2 host3; do
ip netns add ${h}
ip -netns ${h} link set lo up
ip netns exec ${h} sysctl -wq net.ipv4.ip_forward=1
done
ip netns add switch
ip -netns switch li set lo up
ip -netns switch link add br0 type bridge stp 0
ip -netns switch link set br0 up
for n in 1 2 3; do
ip -netns switch link add eth-sw type veth peer name eth-h${n}
ip -netns switch li set eth-h${n} master br0 up
ip -netns switch li set eth-sw netns host${n} name eth0
done
ip -netns host1 addr add 192.168.252.209/24 dev eth0
ip -netns host1 link set dev eth0 up
ip -netns host1 route add 192.168.247.0/24 \
nexthop via 192.168.252.250 dev eth0 nexthop via 192.168.252.252 dev eth0
ip -netns host2 addr add 192.168.252.250/24 dev eth0
ip -netns host2 link set dev eth0 up
ip -netns host2 addr add 192.168.252.252/24 dev eth0
ip -netns host3 link set dev eth0 up
ip netns add tunnel
ip -netns tunnel li set lo up
ip -netns tunnel li add br0 type bridge
ip -netns tunnel li set br0 up
for n in $(seq 11 20); do
ip -netns tunnel addr add dev br0 192.168.247.${n}/24
done
for n in 2 3
do
ip -netns tunnel link add vti${n} type veth peer name eth${n}
ip -netns tunnel link set eth${n} mtu 1360 master br0 up
ip -netns tunnel link set vti${n} netns host${n} mtu 1360 up
ip -netns host${n} addr add dev vti${n} 192.168.247.${n}/24
done
ip -netns tunnel ro add default nexthop via 192.168.247.2 nexthop via 192.168.247.3
ip netns exec host1 ping -M do -s 1400 -c3 -I 192.168.252.209 192.168.247.11
ip netns exec host1 ping -M do -s 1400 -c3 -I 192.168.252.209 192.168.247.15
ip -netns host1 ro ls cache
Before this patch the cache always shows exceptions against the first
leg in the multipath route; 192.168.252.250 per this example. Since the
hash has an initial random seed, you may need to vary the final octet
more than what is listed. In my tests, using addresses between 11 and 19
usually found 1 that used both legs.
With this patch, the cache will have exceptions for both legs.
Fixes: 4895c771c7 ("ipv4: Add FIB nexthop exceptions")
Reported-by: Kfir Itzhak <mastertheknife@gmail.com>
Signed-off-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix parameter description of tipc_link_bc_create()
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: 16ad3f4022 ("tipc: introduce variable window congestion control")
Signed-off-by: Lu Wei <luwei32@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Scenario:
* Multicast frame send from BLA backbone gateways (multiple nodes
with their bat0 bridged together, with BLA enabled) sharing the same
LAN to nodes in the mesh
Issue:
* Nodes receive the frame multiple times on bat0 from the mesh,
once from each foreign BLA backbone gateway which shares the same LAN
with another
For multicast frames via batman-adv broadcast packets coming from the
same BLA backbone but from different backbone gateways duplicates are
currently detected via a CRC history of previously received packets.
However this CRC so far was not performed for multicast frames received
via batman-adv unicast packets. Fixing this by appyling the same check
for such packets, too.
Room for improvements in the future: Ideally we would introduce the
possibility to not only claim a client, but a complete originator, too.
This would allow us to only send a multicast-in-unicast packet from a BLA
backbone gateway claiming the node and by that avoid potential redundant
transmissions in the first place.
Fixes: 279e89b228 ("batman-adv: add broadcast duplicate check")
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Scenario:
* Multicast frame send from mesh to a BLA backbone (multiple nodes
with their bat0 bridged together, with BLA enabled)
Issue:
* BLA backbone nodes receive the frame multiple times on bat0,
once from mesh->bat0 and once from each backbone_gw from LAN
For unicast, a node will send only to the best backbone gateway
according to the TQ. However for multicast we currently cannot determine
if multiple destination nodes share the same backbone if they don't share
the same backbone with us. So we need to keep sending the unicasts to
all backbone gateways and let the backbone gateways decide which one
will forward the frame. We can use the CLAIM mechanism to make this
decision.
One catch: The batman-adv gateway feature for DHCP packets potentially
sends multicast packets in the same batman-adv unicast header as the
multicast optimizations code. And we are not allowed to drop those even
if we did not claim the source address of the sender, as for such
packets there is only this one multicast-in-unicast packet.
How can we distinguish the two cases?
The gateway feature uses a batman-adv unicast 4 address header. While
the multicast-to-unicasts feature uses a simple, 3 address batman-adv
unicast header. So let's use this to distinguish.
Fixes: fe2da6ff27 ("batman-adv: check incoming packet type for bla")
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Scenario:
* Multicast frame send from a BLA backbone (multiple nodes with
their bat0 bridged together, with BLA enabled)
Issue:
* BLA backbone nodes receive the frame multiple times on bat0
For multicast frames received via batman-adv broadcast packets the
originator of the broadcast packet is checked before decapsulating and
forwarding the frame to bat0 (batadv_bla_is_backbone_gw()->
batadv_recv_bcast_packet()). If it came from a node which shares the
same BLA backbone with us then it is not forwarded to bat0 to avoid a
loop.
When sending a multicast frame in a non-4-address batman-adv unicast
packet we are currently missing this check - and cannot do so because
the batman-adv unicast packet has no originator address field.
However, we can simply fix this on the sender side by only sending the
multicast frame via unicasts to interested nodes which do not share the
same BLA backbone with us. This also nicely avoids some unnecessary
transmissions on mesh side.
Note that no infinite loop was observed, probably because of dropping
via batadv_interface_tx()->batadv_bla_tx(). However the duplicates still
utterly confuse switches/bridges, ICMPv6 duplicate address detection and
neighbor discovery and therefore leads to long delays before being able
to establish TCP connections, for instance. And it also leads to the Linux
bridge printing messages like:
"br-lan: received packet on eth1 with own address as source address ..."
Fixes: 2d3f6ccc4e ("batman-adv: Modified forwarding behaviour for multicast packets")
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
For AF_XDP sockets, there was a discrepancy between the number of of
pinned pages and the size of the umem region.
The size of the umem region is used to validate the AF_XDP descriptor
addresses. The logic that pinned the pages covered by the region only
took whole pages into consideration, creating a mismatch between the
size and pinned pages. A user could then pass AF_XDP addresses outside
the range of pinned pages, but still within the size of the region,
crashing the kernel.
This change correctly calculates the number of pages to be
pinned. Further, the size check for the aligned mode is
simplified. Now the code simply checks if the size is divisible by the
chunk size.
Fixes: bbff2f321a ("xsk: new descriptor addressing scheme")
Reported-by: Ciara Loftus <ciara.loftus@intel.com>
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Tested-by: Ciara Loftus <ciara.loftus@intel.com>
Acked-by: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/bpf/20200910075609.7904-1-bjorn.topel@gmail.com
In fl_set_erspan_opt(), all bits of erspan md was set 1, as this
function is also used to set opt MASK. However, when setting for
md->u.index for opt VALUE, the rest bits of the union md->u will
be left 1. It would cause to fail the match of the whole md when
version is 1 and only index is set.
This patch is to fix by initializing with 0 before setting erspan
md->u.
Reported-by: Shuang Li <shuali@redhat.com>
Fixes: 79b1011cb3 ("net: sched: allow flower to match erspan options")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As we can see from vxlan_build/parse_gbp_hdr(), when processing metadata
on vxlan rx/tx path, only dont_learn/policy_applied/policy_id fields can
be set to or parse from the packet for vxlan gbp option.
So do the mask when set it in lwtunnel, as it does in act_tunnel_key and
cls_flower.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As we can see from vxlan_build/parse_gbp_hdr(), when processing metadata
on vxlan rx/tx path, only dont_learn/policy_applied/policy_id fields can
be set to or parse from the packet for vxlan gbp option.
So we'd better do the mask when set it in act_tunnel_key and cls_flower.
Otherwise, when users don't know these bits, they may configure with a
value which can never be matched.
Reported-by: Shuang Li <shuali@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In tipc_buf_append() it may change skb's frag_list, and it causes
problems when this skb is cloned. skb_unclone() doesn't really
make this skb's flag_list available to change.
Shuang Li has reported an use-after-free issue because of this
when creating quite a few macvlan dev over the same dev, where
the broadcast packets will be cloned and go up to the stack:
[ ] BUG: KASAN: use-after-free in pskb_expand_head+0x86d/0xea0
[ ] Call Trace:
[ ] dump_stack+0x7c/0xb0
[ ] print_address_description.constprop.7+0x1a/0x220
[ ] kasan_report.cold.10+0x37/0x7c
[ ] check_memory_region+0x183/0x1e0
[ ] pskb_expand_head+0x86d/0xea0
[ ] process_backlog+0x1df/0x660
[ ] net_rx_action+0x3b4/0xc90
[ ]
[ ] Allocated by task 1786:
[ ] kmem_cache_alloc+0xbf/0x220
[ ] skb_clone+0x10a/0x300
[ ] macvlan_broadcast+0x2f6/0x590 [macvlan]
[ ] macvlan_process_broadcast+0x37c/0x516 [macvlan]
[ ] process_one_work+0x66a/0x1060
[ ] worker_thread+0x87/0xb10
[ ]
[ ] Freed by task 3253:
[ ] kmem_cache_free+0x82/0x2a0
[ ] skb_release_data+0x2c3/0x6e0
[ ] kfree_skb+0x78/0x1d0
[ ] tipc_recvmsg+0x3be/0xa40 [tipc]
So fix it by using skb_unshare() instead, which would create a new
skb for the cloned frag and it'll be safe to change its frag_list.
The similar things were also done in sctp_make_reassembled_event(),
which is using skb_copy().
Reported-by: Shuang Li <shuali@redhat.com>
Fixes: 37e22164a8 ("tipc: rename and move message reassembly function")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tipc_group_add_to_tree() returns silently if `key` matches `nkey` of an
existing node, causing tipc_group_create_member() to leak memory. Let
tipc_group_add_to_tree() return an error in such a case, so that
tipc_group_create_member() can handle it properly.
Fixes: 75da2163db ("tipc: introduce communication groups")
Reported-and-tested-by: syzbot+f95d90c454864b3b5bc9@syzkaller.appspotmail.com
Cc: Hillf Danton <hdanton@sina.com>
Link: https://syzkaller.appspot.com/bug?id=048390604fe1b60df34150265479202f10e13aff
Signed-off-by: Peilin Ye <yepeilin.cs@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
flowi4_multipath_hash was added by the commit referenced below for
tunnels. Unfortunately, the patch did not initialize the new field
for several fast path lookups that do not initialize the entire flow
struct to 0. Fix those locations. Currently, flowi4_multipath_hash
is random garbage and affects the hash value computed by
fib_multipath_hash for multipath selection.
Fixes: 24ba14406c ("route: Add multipath_hash in flowi_common to make user-define hash")
Signed-off-by: David Ahern <dsahern@gmail.com>
Cc: wenxu <wenxu@ucloud.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
The fix for receiving (internally generated) bla packets outside the
interrupt context introduced the usage of in_interrupt(). But this
functionality is only defined in linux/preempt.h which was not included
with the same patch.
Fixes: 279e89b228 ("batman-adv: bla: use netif_rx_ni when not in interrupt context")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
It's possible that the user specifies an interval that couldn't allow
any packet to be transmitted. This also avoids the issue of the
hrtimer handler starving the other threads because it's running too
often.
The solution is to reject interval sizes that according to the current
link speed wouldn't allow any packet to be transmitted.
Reported-by: syzbot+8267241609ae8c23b248@syzkaller.appspotmail.com
Fixes: 5a781ccbd1 ("tc: Add support for configuring the taprio scheduler")
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The parameter passed via DCB_ATTR_DCB_BUFFER is a struct dcbnl_buffer. The
field prio2buffer is an array of IEEE_8021Q_MAX_PRIORITIES bytes, where
each value is a number of a buffer to direct that priority's traffic to.
That value is however never validated to lie within the bounds set by
DCBX_MAX_BUFFERS. The only driver that currently implements the callback is
mlx5 (maintainers CCd), and that does not do any validation either, in
particual allowing incorrect configuration if the prio2buffer value does
not fit into 4 bits.
Instead of offloading the need to validate the buffer index to drivers, do
it right there in core, and bounce the request if the value is too large.
CC: Parav Pandit <parav@nvidia.com>
CC: Saeed Mahameed <saeedm@nvidia.com>
Fixes: e549f6f9c0 ("net/dcb: Add dcbnl buffer attribute")
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a netdev is enslaved to a bridge, its parent identifier is queried.
This is done so that packets that were already forwarded in hardware
will not be forwarded again by the bridge device between netdevs
belonging to the same hardware instance.
The operation fails when the netdev is an upper of netdevs with
different parent identifiers.
Instead of failing the enslavement, have dev_get_port_parent_id() return
'-EOPNOTSUPP' which will signal the bridge to skip the query operation.
Other callers of the function are not affected by this change.
Fixes: 7e1146e8c1 ("net: devlink: introduce devlink_compat_switch_id_get() helper")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reported-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 8d7017fd62 ("blackhole_netdev: use blackhole_netdev to
invalidate dst entries"), we use blackhole_netdev to invalidate dst entries
instead of loopback device anymore.
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently there is concurrent reset and enqueue operation for the
same lockless qdisc when there is no lock to synchronize the
q->enqueue() in __dev_xmit_skb() with the qdisc reset operation in
qdisc_deactivate() called by dev_deactivate_queue(), which may cause
out-of-bounds access for priv->ring[] in hns3 driver if user has
requested a smaller queue num when __dev_xmit_skb() still enqueue a
skb with a larger queue_mapping after the corresponding qdisc is
reset, and call hns3_nic_net_xmit() with that skb later.
Reused the existing synchronize_net() in dev_deactivate_many() to
make sure skb with larger queue_mapping enqueued to old qdisc(which
is saved in dev_queue->qdisc_sleeping) will always be reset when
dev_reset_queue() is called.
Fixes: 6b3ba9146f ("net: sched: allow qdiscs to handle locking")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch set the init remote_id to zero, otherwise it will be a random
number.
Then it added the missing subflow's remote_id setting code both in
__mptcp_subflow_connect and in subflow_ulp_clone.
Fixes: 01cacb00b3 ("mptcp: add netlink-based PM")
Fixes: ec3edaa7ca ("mptcp: Add handling of outgoing MP_JOIN requests")
Fixes: f296234c98 ("mptcp: Add handling of incoming MP_JOIN requests")
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
In mptcp_pm_nl_get_local_id, skc_local is the same as msk_local, so it
always return 0. Thus every subflow's local_id is 0. It's incorrect.
This patch fixed this issue.
Also, we need to ignore the zero address here, like 0.0.0.0 in IPv4. When
we use the zero address as a local address, it means that we can use any
one of the local addresses. The zero address is not a new address, we don't
need to add it to PM, so this patch added a new function address_zero to
check whether an address is the zero address, if it is, we ignore this
address.
Fixes: 01cacb00b3 ("mptcp: add netlink-based PM")
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I confirmed that the problem fixed by commit 2a63866c8b ("tipc: fix
shutdown() of connectionless socket") also applies to stream socket.
----------
#include <sys/socket.h>
#include <unistd.h>
#include <sys/wait.h>
int main(int argc, char *argv[])
{
int fds[2] = { -1, -1 };
socketpair(PF_TIPC, SOCK_STREAM /* or SOCK_DGRAM */, 0, fds);
if (fork() == 0)
_exit(read(fds[0], NULL, 1));
shutdown(fds[0], SHUT_RDWR); /* This must make read() return. */
wait(NULL); /* To be woken up by _exit(). */
return 0;
}
----------
Since shutdown(SHUT_RDWR) should affect all processes sharing that socket,
unconditionally setting sk->sk_shutdown to SHUTDOWN_MASK will be the right
behavior.
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
clean follow coccicheck warning:
net//hsr/hsr_netlink.c:94:8-42: WARNING avoid newline at end of message
in NL_SET_ERR_MSG_MOD
net//hsr/hsr_netlink.c:87:30-57: WARNING avoid newline at end of message
in NL_SET_ERR_MSG_MOD
net//hsr/hsr_netlink.c:79:29-53: WARNING avoid newline at end of message
in NL_SET_ERR_MSG_MOD
Signed-off-by: Ye Bin <yebin10@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Highlights include:
Bugfixes:
- Fix an NFS/RDMA resource leak
- Fix the error handling during delegation recall
- NFSv4.0 needs to return the delegation on a zero-stateid SETATTR
- Stop printk reading past end of string
-----BEGIN PGP SIGNATURE-----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=3fw2
-----END PGP SIGNATURE-----
Merge tag 'nfs-for-5.9-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client bugfixes from Trond Myklebust:
- Fix an NFS/RDMA resource leak
- Fix the error handling during delegation recall
- NFSv4.0 needs to return the delegation on a zero-stateid SETATTR
- Stop printk reading past end of string
* tag 'nfs-for-5.9-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
SUNRPC: stop printk reading past end of string
NFS: Zero-stateid SETATTR should first return delegation
NFSv4.1 handle ERR_DELAY error reclaiming locking state on delegation recall
xprtrdma: Release in-flight MRs on disconnect
Currently, in tcp_v4_reqsk_send_ack() and tcp_v4_send_reset(), we
echo the TOS value of the received packets in the response.
However, we do not want to echo the lower 2 ECN bits in accordance
with RFC 3168 6.1.5 robustness principles.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stefan Schmidt says:
====================
pull-request: ieee802154 for net 2020-09-08
An update from ieee802154 for your *net* tree.
A potential memory leak fix for ca8210 from Liu Jian,
a check on the return for a register read in adf7242
and finally a user after free fix in the softmac tx
function from Eric found by syzkaller.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
If CONFIG_IPV6=m, the IPV6 functions won't be found by the linker:
ld: net/core/fib_rules.o: in function `fib_rules_lookup':
fib_rules.c:(.text+0x606): undefined reference to `fib6_rule_match'
ld: fib_rules.c:(.text+0x611): undefined reference to `fib6_rule_match'
ld: fib_rules.c:(.text+0x68c): undefined reference to `fib6_rule_action'
ld: fib_rules.c:(.text+0x693): undefined reference to `fib6_rule_action'
ld: fib_rules.c:(.text+0x6aa): undefined reference to `fib6_rule_suppress'
ld: fib_rules.c:(.text+0x6bc): undefined reference to `fib6_rule_suppress'
make: *** [Makefile:1166: vmlinux] Error 1
Reported-by: Sven Joachim <svenjoac@gmx.de>
Fixes: b9aaec8f0b ("fib: use indirect call wrappers in the most common fib_rules_ops")
Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Signed-off-by: Brian Vazquez <brianvv@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds
Eric Dumazet
Vladimir Oltean
David S. Miller
Xu Wang
Chuck Lever
Henry Ptasinski
Necip Fazil Yildiran
John Crispin
Felix Fietkau
Johannes Berg
Wen Gong
Aloka Dixit
Michal Kubecek
Martin KaFai Lau
David Ahern
Lu Wei
Linus Lüssing
Björn Töpel
Xin Long
Peilin Ye
David Ahern
Sven Eckelmann
Vinicius Costa Gomes
Petr Machata
Ido Schimmel
Miaohe Lin
Yunsheng Lin
Geliang Tang
Tetsuo Handa
Ye Bin
Wei Wang
Brian Vazquez