For new stepping of PCH, the display reference clock
is fully under driver's control. This one trys to setup
all needed reference clock for different outputs. Older
stepping of PCH chipset should be ignoring this.
This fixes output failure issue on newer PCH which requires
driver to take control of reference clock enabling.
Cc: Stable Team <stable@kernel.org>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
To enable framebuffer compression on a g4x, we not only need the buffer
to tiled (X only), we also need to hold a fence register for the buffer.
Currently we only install a fence register for pre-i965s when setting up
the scanout buffer. Rather than adding some convoluted logic to
g4x_enable_fbc() to acquire a fence register, and perhaps to
g4x_disable_fbc() to release it again, we can extend the acquisition
during setup to all chipsets.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Turns out some machines, like the ThinkPad X40 don't come back if you
don't save/restore this register.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
FDI M/N calculation hasn't taken the current pipe color depth into account,
but always set as 24bpp. This one checks current pipe color depth setting,
and change FDI M/N calculation a little to use bits_per_pixel first, then
convert to bytes_per_pixel later.
This fixes display corrupt issue on Arrandle LVDS with 1600x900 panel
in 18bpp dual-channel mode.
Cc: Stable Team <stable@kernel.org>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Until we figure out the right setting for powersave features on
Ironlake, disable it for now. Also disable watermark update,
which has new registers for it on Ironlake too.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[anholt: Resolved against the Pineview FBC changes]
Signed-off-by: Eric Anholt <eric@anholt.net>
If the device didn't support EDP, we would bail out too soon.
Signed-off-by: Andy Lutomirski <luto@mit.edu>
[anholt: Pulled this patch out of the patch for adding quirks to
enable reclocking.]
Signed-off-by: Eric Anholt <eric@anholt.net>
This hasn't fixed the regressions we were testing against, but clearly
should be required.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
According to the spec the LVDS_BORDER_ENABLE bit decides whether the border
data should be included in the active display and data sent to the panel.
Border should be used when in VGA centered (un-scaled) mode or when scaling
a 4:3 source image to a wide screen panel (typical 16:9).
So when the LVDS scaling is used, decide whether the LVDS_BORDER should be
enabled or not according to the current scaling mode.
At the same time fix the typo error in LVDS center scaling mode.
https://bugs.freedesktop.org/show_bug.cgi?id=23789
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
tested-by: Zhao Jian <jian.zhao@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Pineview doesn't have this FBC mechanism, so this code doesn't apply.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
* 'drm-intel-next' of git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel:
drm/i915: Initialize HDMI outputs as HDMI connectors, not DVI.
drm/i915: Multiply the refresh by 1000 in TV mode validatiion
drm/i915: Enable irq to trace batch buffer completion.
drm/i915: batch submit seqno off-by-one.
drm/i915: Record device minor rather than pointer in TRACE_EVENT
drm/i915: Don't call intel_update_fbc from intel_crtc_cursor_set
conflict in radeon since new init path merged with vga arb code.
Conflicts:
drivers/gpu/drm/radeon/radeon.h
drivers/gpu/drm/radeon/radeon_asic.h
drivers/gpu/drm/radeon/radeon_device.c
The previous patches had some unwanted side effects, I've fixed
the lack of 32bpp working, and fixed up 16bpp so it should also work.
this also adds the interface to allow the driver to set a preferred
console depth so for example low memory rn50 can set it to 8bpp.
It also catches 24bpp on cards that can't do it and forces 32bpp.
Tested on r100/r600/i945.
Signed-off-by: Dave Airlie <airlied@redhat.com>
This adds support for the setcmap api and fixes the 8bpp
support at least on radeon hardware. It adds a new load_lut
hook which can be called once the color map is setup.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Even if the physical output connector is DVI, calling it HDMI
tells the user that there's HDMI audio signaling support.
Signed-off-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
As of 559ee21d26 the actual refresh rate
is returned by the function of drm_mode_vrefresh, so multiply the refresh
rate by 1000 in TV mode validation.
At the same time the error is expanded from 10 to 1000.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
* 'drm-next' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (25 commits)
drm/radeon/kms: Convert R520 to new init path and associated cleanup
drm/radeon/kms: Convert RV515 to new init path and associated cleanup
drm: fix radeon DRM warnings when !CONFIG_DEBUG_FS
drm: fix drm_fb_helper warning when !CONFIG_MAGIC_SYSRQ
drm/r600: fix memory leak introduced with 64k malloc avoidance fix.
drm/kms: make fb helper work for all drivers.
drm/radeon/r600: fix offset handling in CS parser
drm/radeon/kms/r600: fix forcing pci mode on agp cards
drm/radeon/kms: fix for the extra pages copying.
drm/radeon/kms/r600: add support for vline relocs
drm/radeon/kms: fix some bugs in vline reloc
drm/radeon/kms/r600: clamp vram to aperture size
drm/kms: protect against fb helper not being created.
drm/r600: get values from the passed in IB not the copy.
drm: create gitignore file for radeon
drm/radeon/kms: remove unneeded master create/destroy functions.
drm/kms: start adding command line interface using fb.
fb: change rules for global rules match.
drm/radeon/kms: don't require up to 64k allocations. (v2)
drm/radeon/kms: enable dac load detection by default.
...
Trivial conflicts in drivers/gpu/drm/radeon/radeon_asic.h due to adding
'->vga_set_state' function pointers.
If we trigger a tracepoint for batch buffer submission, it is a reasonable
assumption that we wish to also trace the batch buffer completion. So in
order to capture the completion events, we need to enable irqs... However,
we cannot rely on the completion event to disable the irq later, so we
defer the irq disable to the retire request.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
We increment the seqno number between submitting the batch buffer and
the flush/interrupt that demarcates its end, so the tracepoint needs to
reference the incremented value to match the completion event.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Commit 74dff282 exposed this unnecessary call by causing a change in
the failure path on i965 where framebuffer compression will be turned
on and off on every cursor update. If you don't have the xf86-video-intel
fix to avoid the blinking cursor effect, this is very slow.
Symptoms were a far more noticeable cursor blink with every cursor image
change combined with severe slowdown for animated cursors.
Signed-off-by: Brian Rogers <brian@xyzw.org>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
[note this requires an fb patch posted to linux-fbdev-devel already]
This uses the normal video= command line option to control the kms
output setup at boot time. It is used to override the autodetection
done by kms.
video= normally takes a framebuffer as the first parameter, in kms
it will take a connector name, DVI-I-1, or LVDS-1 etc. If no output
connector is specified the mode string will apply to all connectors.
The mode specification used will match down the probed modes, and if
no mode is found it will add a CVT mode that matches.
video=1024x768 - all connectors match a 1024x768 mode or add a CVT on
video=VGA-1:1024x768, VGA-1 connector gets mode only.
The same strings as used in current fb modedb.c are used, except I've
added three more letters, e, D, d, e = enable, D = enable Digital,
d = disable, which allow a connector to be forced into a certain state.
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'drm-intel-next' of git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel: (57 commits)
drm/i915: Handle ERESTARTSYS during page fault
drm/i915: Warn before mmaping a purgeable buffer.
drm/i915: Track purged state.
drm/i915: Remove eviction debug spam
drm/i915: Immediately discard any backing storage for uneeded objects
drm/i915: Do not mis-classify clean objects as purgeable
drm/i915: Whitespace correction for madv
drm/i915: BUG_ON page refleak during unbind
drm/i915: Search harder for a reusable object
drm/i915: Clean up evict from list.
drm/i915: Add tracepoints
drm/i915: framebuffer compression for GM45+
drm/i915: split display functions by chip type
drm/i915: Skip the sanity checks if the current relocation is valid
drm/i915: Check that the relocation points to within the target
drm/i915: correct FBC update when pipe base update occurs
drm/i915: blacklist Acer AspireOne lid status
ACPI: make ACPI button funcs no-ops if not built in
drm/i915: prevent FIFO calculation overflows on 32 bits with high dotclocks
drm/i915: intel_display.c handle latency variable efficiently
...
Fix up trivial conflicts in drivers/gpu/drm/i915/{i915_dma.c|i915_drv.h}
During a page fault and rebinding the buffer there exists a window for a
signal to arrive during the i915_wait_request() and trigger a
ERESTARTSYS. This used to be handled by returning SIGBUS and thereby
killing the application. Try 'cairo-perf-trace & cairo-test-suite' and
watch X go boom!
The solution as suggested by H. Peter Anvin is to simply return NOPAGE and
leave the higher layers to spot we did not fill the page and resubmit
the page fault.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
[anholt: Mostly squash it with another commit]
In order to correctly prevent the invalid reuse of a purged buffer, we
need to track such events and warn the user before something bad
happens.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Whilst cleaning up the patches for submission, I mis-classified non-dirty
objects as purgeable. This was causing the backing pages for those
objects to be evicted under memory-pressure, discarding valid and
unreplaceable texture data.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
As evict_something() is called by routines that do not repeatedly search
again, try harder in the initial search to find an object that matches
the request.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
First the routine attempted to unlock a mutex it did not own along the
error path.
Secondly the routine should never be called on any list but the inactive
one, since we attempt to unbind those objects, so fix the calling semantics.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
By adding tracepoint equivalents for WATCH_BUF/EXEC we are able to monitor
the lifetimes of objects, requests and significant events. These events can
then be probed using the tracing frameworks, such as systemtap and, in
particular, perf.
For example to record the stack trace for every GPU stall during a run, use
$ perf record -e i915:i915_gem_request_wait_begin -c 1 -g
And
$ perf report
to view the results.
[Updated to fix compilation issues caused.]
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Ben Gamari <bgamari@gmail.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (34 commits)
trivial: fix typo in aic7xxx comment
trivial: fix comment typo in drivers/ata/pata_hpt37x.c
trivial: typo in kernel-parameters.txt
trivial: fix typo in tracing documentation
trivial: add __init/__exit macros in drivers/gpio/bt8xxgpio.c
trivial: add __init macro/ fix of __exit macro location in ipmi_poweroff.c
trivial: remove unnecessary semicolons
trivial: Fix duplicated word "options" in comment
trivial: kbuild: remove extraneous blank line after declaration of usage()
trivial: improve help text for mm debug config options
trivial: doc: hpfall: accept disk device to unload as argument
trivial: doc: hpfall: reduce risk that hpfall can do harm
trivial: SubmittingPatches: Fix reference to renumbered step
trivial: fix typos "man[ae]g?ment" -> "management"
trivial: media/video/cx88: add __init/__exit macros to cx88 drivers
trivial: fix typo in CONFIG_DEBUG_FS in gcov doc
trivial: fix missing printk space in amd_k7_smp_check
trivial: fix typo s/ketymap/keymap/ in comment
trivial: fix typo "to to" in multiple files
trivial: fix typos in comments s/DGBU/DBGU/
...
Add support for framebuffer compression on GM45 and above. Removes
some unnecessary I915_HAS_FBC checks as well (this is now part of the
FBC display function).
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
This patch splits out several of the display functions into a separate
display function table to avoid tons of chipset specific if..else
if..else if blocks all over. There are more opportunities for this
(some noted in the structure defintition); so more cleanup patches will
follow.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (133 commits)
drm/vgaarb: add VGA arbitration support to the drm and kms.
drm/radeon: some r420s have a CP race with the DMA engine.
drm/radeon/r600/kms: rv670 is not DCE3
drm/radeon/kms: r420 idle after programming GA_ENHANCE
drm/radeon/kms: more fixes to rv770 suspend/resume path.
drm/radeon/kms: more alignment for rv770.c with r600.c
drm/radeon/kms: rv770 blit init called too late.
drm/radeon/kms: move around new init path code to avoid posting at init
drm/radeon/r600: fix some issues with suspend/resume.
drm/radeon/kms: disable VGA rendering engine before taking over VRAM
drm/radeon/kms: Move radeon_get_clock_info() call out of radeon_clocks_init().
drm/radeon/kms: add initial connector properties
drm/radeon/kms: Use surfaces for scanout / cursor byte swapping on big endian.
drm/radeon/kms: don't fail if we fail to init GPU acceleration
drm/r600/kms: fixup number of loops per blit calculation.
drm/radeon/kms: reprogram format in set base.
drm/radeon: avivo chips have no separate int bit for display
drm/radeon/r600: don't do interrupts
drm: fix _DRM_GEM addmap error message
drm: update crtc x/y when only fb changes
...
Fixed up trivial conflicts in firmware/Makefile due to network driver
(cxgb3) and drm (mga/r128/radeon) firmware being listed next to each
other.
VGA arb requires DRM support for non-kms drivers, to turn on/off
irqs when disabling the mem/io regions.
VGA arb requires KMS support for GPUs where we can turn off VGA
decoding. Currently we know how to do this for intel and radeon
kms drivers, which allows them to be removed from the arbiter.
This patch comes from Fedora rawhide kernel.
Signed-off-by: Dave Airlie <airlied@redhat.com>
If the presumed_offset as feed to userspace and returned to the kernel
from a previous execbuffer is still valid, then we do not need to rewrite
the relocation entry and may skip the offset sanity checks.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Eric noted a potential concern with the low bits not being strictly used
as part of the absolute offset (instead part of the command stream to the
GPU), but in practice that should not be an issue.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Andy Whitcroft <apw@canonical.com>
Cc: Eric Anholt <eric@anholt.net>
CC: stable@kernel.org
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
We usually don't have an SAREA, and we always want to update the FBC
status anyway, so move the update up above the various master/sarea
checks.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
It reports closed when open, leading to "no outputs found" at startup
unless a VGA cable is plugged in.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
A very high dotclock (e.g. 229500kHz as reported by Anton) can cause
the entries_required variable to overflow, potentially leading to a
FIFO watermark value that's too low to support the given mode. Split
the division across the calculation to avoid this.
Cc: stable@kernel.org
Reported-by: Anton Khirnov <wyskas@gmail.com>
Tested-by: Anton Khirnov <wyskas@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
By handling latency variable efficiently we also get rid of this warning :
CC [M] drivers/gpu/drm/i915/intel_display.o
drivers/gpu/drm/i915/intel_display.c: In function ‘igd_enable_cxsr’:
drivers/gpu/drm/i915/intel_display.c:1918: warning: ‘latency’ may be used uninitialized in this function
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Don't need extra config restore like for intel_agp, which
might cause resume hang issue found by Alan on 845G.
Cc: Stable Team <stable@kernel.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Due to the necessity of having to take the struct_mutex, the i915
shrinker can not free the inactive lists if we fail to allocate memory
whilst processing a batch buffer, triggering an OOM and an ENOMEM that
is reported back to userspace. In order to fare better under such
circumstances we need to manually retry a failed allocation after
evicting inactive buffers.
To do so involves 3 steps:
1. Marking the backing shm pages as NORETRY.
2. Updating the get_pages() callers to evict something on failure and then
retry.
3. Revamping the evict something logic to be smarter about the required
buffer size and prefer to use volatile or clean inactive pages.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Similar to the madvise() concept, the application may wish to mark some
data as volatile. That is in the event of memory pressure the kernel is
free to discard such buffers safe in the knowledge that the application
can recreate them on demand, and is simply using these as a cache.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This should help GEM handle memory pressure sitatuions more gracefully.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
There is no need to store the gtt_alignment as it is either explicitly
set according to the hardware requirements (e.g. scanout) or the
minimum alignment is computed on demand.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
If we failed to set the domain, the buffer was no longer being tracked
on any list.
Cc: stable@kernel.org
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Due to a bogus FBC support check and failing to check for FBC support
in the right places, mode setting on non-mobile platforms could fail
and hang in the FBC disable routine. Fix it up.
This fix highlights the need for cleanups in this area (function
pointers and better feature support checks). Patches for that to
follow.
Tested-by: Kenny Graunke <kenny@whitecape.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
We now unconditionally restore the mode at lid open time since some
platforms turn off the panel, pipes or other display elements when the
lid is closed. There's a problem with doing this at resume time
however.
At resume time, we'll get a lid event, but restoring the mode at that
time may not be safe (e.g. if we get the lid event before global state
has been restored), so check the suspended state and make sure our
restore is locked against other mode updates.
Tested-by: Ben Gamari <bgamari.foss@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
There is a very real possibility that multiple CPUs will notice that the
GPU is wedged. This introduces all sorts of potential race conditions.
Make the wedged flag atomic to mitigate this risk.
Signed-off-by: Ben Gamari <bgamari.foss@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch uses the previously introduced chip reset logic to reset the
chip when an error event is detected.
Signed-off-by: Ben Gamari <bgamari.foss@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch puts in place the machinery to attempt to reset the GPU. This
will be used when attempting to recover from a GPU hang.
Signed-off-by: Owain G. Ainsworth <oga@openbsd.org>
Signed-off-by: Ben Gamari <bgamari.foss@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
We set a periodic timer to check on the GPU, resetting it every time a
batch is completed. If the timer elapses, we check acthd. If acthd
hasn't changed in two timer periods, we assume the chip is wedged.
This is implemented in such a way that it leaves the option open to
employ adaptive timer intervals in the future. One could wait until
several timer periods have elapsed before declaring the chip dead. If
the chip comes back after several periods but before the "dead"
threshold, the timer interval or dead threshold could be raised.
It is important to note that while checking for active requests, we need
to account for the fact that requests are removed from the list (i.e.
retired) in a deferred work queue handler. This means that merely
checking for an empty request_list is insufficient; the list could be
non-empty yet the GPU still idle, causing the hangcheck timer to
incorrectly mark the GPU as wedged (it took me a while to figure that
out---sigh...)
Signed-off-by: Ben Gamari <bgamari.foss@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
We'll need it in i915_irq.c for checking whether there are outstanding
requests. Also, the function really ought to return a bool, not an int.
Signed-off-by: Ben Gamari <bgamari.foss@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
We move the display-specific code into it's own functions, called
from the general GPU state save/restore functions. This will be needed
later by the GPU reset code.
Signed-off-by: Ben Gamari <bgamari.foss@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
i915_wait_request() only checks mm.wedged after it interacts with the
hardware, generally causing the driver to lock up waiting for a wedged
chip. Make sure we check mm.wedged as the first thing we do.
Reported-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ben Gamari <bgamari.foss@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
BLC_PWM_CTL2 is for 965+ only, so add device model check for
legacy backlight control.
For native backlight control, it maps the backlight value (0~255)
in opregion ASLE[BCLP] to backlight duty cycle (0~max_backlight)
and set into control register.
It also add support for IGD device, which follows opregion spec.
Signed-off-by: Li Peng <peng.li@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Arrandale has new window based method for panel fitting.
This one enables full screen aspect scaling on LVDS. It fixes
standard mode display failure on LVDS for Arrandale.
Cc: Stable Team <stable@kernel.org>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This is not required on newer stepping hardware to get
reliable force detect status. Removing this fixes screen
blank flicker in CRT detect on IGDNG.
Cc: Stable Team <stable@kernel.org>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
IGDNG LVDS SSC uses 120Mhz freq. This fixes one
1600x900 LVDS panel black issue on IGDNG with SSC enabled.
Cc: Stable Team <stable@kernel.org>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
New register for PCH LVDS on IGDNG should be used.
This is a copy-n-paste typo. This fixes possible dual
channel LVDS panel failure on IGDNG.
Cc: Stable Team <stable@kernel.org>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
drm_ht_remove_item() does not handle removing an absent item and the hlist
in particular is incorrectly initialised. The easy remedy is simply skip
calling i915_gem_free_mmap_offset() unless we have actually created the
offset and associated ht entry.
This also fixes the mishandling of a partially constructed offset which
leaves pointers initialized after freeing them along the
i915_gem_create_mmap_offset() error paths.
In particular this should fix the oops found here:
https://bugs.launchpad.net/ubuntu/+source/xserver-xorg-video-intel/+bug/415357/comments/8
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Cc: stable@kernel.org
Ever since we enabled GEM, the pre-9xx chipsets (particularly 865) have had
serious stability issues. Back in May a wbinvd was added to the DRM to
work around much of the problem. Some failure remained -- easily visible
by dragging a window around on an X -retro desktop, or by looking at bugzilla.
The chipset flush was on the right track -- hitting the right amount of
memory, and it appears to be the only way to flush on these chipsets, but the
flush page was mapped uncached. As a result, the writes trying to clear the
writeback cache ended up bypassing the cache, and not flushing anything! The
wbinvd would flush out other writeback data and often cause the data we wanted
to get flushed, but not always. By removing the setting of the page to UC
and instead just clflushing the data we write to try to flush it, we get the
desired behavior with no wbinvd.
This exports clflush_cache_range(), which was laying around and happened to
basically match the code I was otherwise going to copy from the DRM.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Brice Goglin <Brice.Goglin@ens-lyon.org>
Cc: stable@kernel.org
This patch adds framebuffer compression (good for about ~0.5W power
savings in the best case) support for pre-GM45 chips. GM45+ have a new,
more flexible FBC scheme that will be added in a separate patch.
FBC can't always be enabled: the compressed buffer must be physically
contiguous and reside in stolen space. So if you have a large display
and a small amount of stolen memory, you may not be able to take
advantage of FBC. In some cases, a BIOS setting controls how much
stolen space is available. Increasing this to 8 or 16M can help.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
With all the other lid pieces in place, it's easy to generate a uevent
for the LVDS connector just like we do for other outputs. Should make
lid open/close fit in with the rest of a userland based output
reconfiguration scheme.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
We can't load or hotplug detect LVDS like we can other outputs, but if
there's a lid device present we can use it as a proxy. This allows the
LFP state to be determined at ->detect time, making configurations
requiring manual intervention today "just work" assuming the lid device
status is correct.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Some laptop platforms will disable pipes and/or planes at lid close time
and not restore them when the lid is opened again. So catch the lid
event, and if the lid was opened, force a mode restore.
Fixes fdo bug #21230.
Acked-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
When the output device is LVDS, maybe the pixel clock of adjusted_mode will be
less than that in mode. In such case it will set the incorrect multipler factor
in DPLL_MD register.
So the dpll_md_reg will be reset when the output type is non-SDVO
https://bugs.freedesktop.org/show_bug.cgi?id=22761
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Reviewd-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Eric Anholt <eric@anholt.net>
When the sdvo device is detected as SDVO-LVDS, we will check whether the
brightness is supported by issue SDVO enhancement command.
If it is supported, we will add the brightness property and then brightness
can be adjusted.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
When the sdvo device is detected as SDVO-TV, we will check whether the
sepecific picture enhancement is supported. If it is supported, we will
add the corresponnding property for SDVO-TV. We will add the following
property for the SDVO-TV enhancements if they are supported:
* Contrast/Brightness/Saturation/Hue.
* left/right/top/bottom margin: This is implemented by using the
horizontal/vertical overscan enhancements. When the overscan
enhancements are supported, the above properties will be added. This is
to be compatible with what we have done in integrated-TV.
* horizontal pos/vertical pos.
http://bugs.freedesktop.org/show_bug.cgi?id=22891
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Otherwise, some other userland writing into its buffer may race to land
writes either after the CPU thinks it's got a coherent view, or after its
GTT entries have been redirected to point at the scratch page. Either
result is unpleasant.
Signed-off-by: Eric Anholt <eric@anholt.net>
Reinette Chatre reports a frozen system (with blinking keyboard LEDs)
when switching from graphics mode to the text console, or when
suspending (which does the same thing). With netconsole, the oops
turned out to be
BUG: unable to handle kernel NULL pointer dereference at 0000000000000084
IP: [<ffffffffa03ecaab>] i915_driver_irq_handler+0x26b/0xd20 [i915]
and it's due to the i915_gem.c code doing drm_irq_uninstall() after
having done i915_gem_idle(). And the i915_gem_idle() path will do
i915_gem_idle() ->
i915_gem_cleanup_ringbuffer() ->
i915_gem_cleanup_hws() ->
dev_priv->hw_status_page = NULL;
but if an i915 interrupt comes in after this stage, it may want to
access that hw_status_page, and gets the above NULL pointer dereference.
And since the NULL pointer dereference happens from within an interrupt,
and with the screen still in graphics mode, the common end result is
simply a silently hung machine.
Fix it by simply uninstalling the irq handler before idling rather than
after. Fixes
http://bugzilla.kernel.org/show_bug.cgi?id=13819
Reported-and-tested-by: Reinette Chatre <reinette.chatre@intel.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
eDP is exclusive connector too, and add missing crtc_mask
setting for TV.
This fixes
http://bugzilla.kernel.org/show_bug.cgi?id=14139
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Reported-and-tested-by: Carlos R. Mafra <crmafra2@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The driver gets the bridge device in a number of places, upcoming
vga arb code paths need the bridge device, however they need it in
under a lock, and the pci lookup can allocate memory. So clean
this code up before then and get the bridge once for the driver lifetime.
Signed-off-by: Dave Airlie <airlied@redhat.com>
According to the docs, the ringbuffer is not allowed to wrap in the middle
of an instruction.
G45 PRM, Vol 1b, p101:
While the “free space” wrap may allow commands to be wrapped around the
end of the Ring Buffer, the wrap should only occur between commands.
Padding (with NOP) may be required to follow this restriction.
Do as commanded.
[Having seen bug reports where there is evidence of split commands, but
apparently the GPU has continued on merrily before a bizarre and untimely
death, this may or may not fix a few random hangs.]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
CC: Eric Anholt <eric@anholt.net>
Signed-off-by: Eric Anholt <eric@anholt.net>
mac Mini's have a single DDC line on the DVI connector, shared between the
analog link and the digital link. So, if DDC isn't detected on GPIOE (the
usual SDVO DDC link), try GPIOA (the usual VGA DDC link) when there isn't a
VGA monitor connected.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
It seems that on IGDNG the same swizzling setup always applys.
And front buffer tiling needs to set address swizzle in display
arb control too.
Fix plane tricle feed setting in v1 which should be disable bit,
and always setup address swizzle to let hardware care for buffer
tiling in all cases.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
And clean up a small whitespace goof-up in the same function, while
I was looking at it.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Eric Anholt <eric@anholt.net>
There are several sources of unnecessary power consumption on Intel
graphics systems. The first is the LVDS clock. TFTs don't suffer from
persistence issues like CRTs, and so we can reduce the LVDS refresh rate
when the screen is idle. It will be automatically upclocked when
userspace triggers graphical activity. Beyond that, we can enable memory
self refresh. This allows the memory to go into a lower power state when
the graphics are idle. Finally, we can drop some clocks on the gpu
itself. All of these things can be reenabled between frames when GPU
activity is triggered, and so there should be no user visible graphical
changes.
Signed-off-by: Jesse Barnes <jesse.barnes@intel.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
In the event that any one of the DAC analog outputs (R,G,B) were driven
at full-scale (white video) or some analog level close to full-scale
voltage, and if the video cable were then disconnected, the analog video
voltage level would exceed the maximum electrical overstress limit of the
native (thin-oxide) transistors thus causing a long-term reliability concern.
The electrical overstress condition occurs in this particular case.
This patch address the IGD EOS (electrical overstress condition) issue.
When the EOS interrupt occurs, OS should disable DAC and then disable EOS,
then the normal hotplug operation follows.
TODO: it appears the normal unplug interrupt is missed as reported by Li Peng,
need more checks here.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Currently SDVO TV only support NTSC-M format. In this patch
we introduce PAL and SECAM formats available and create seting-format
property at init time. When user dynamically chose preferred
format by xrandr command, it will refine all modelines
provided by SDVO device, then instruct SDVO device to execute.
At the same time the property is added for SDVO-TV so that the SDVO-TV mode can be changed
by using xrandr.
https://bugs.freedesktop.org/show_bug.cgi?id=22891
Signed-off-by: Ma Ling <ling.ma@intel.com>
review-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
For integrated TV there are 3 connector types: S-VIDEO, Composite and
Component(YprPb). Those tv formats whose component flag is true should
be assigned to Component connector, others are for S-VIDEO and Composite.
The patch intends to find appropriate tv format for each connector.
In such case it will return the correct modeline to user space. Otherwise
it will return the incorrect modeline when S-video/composite is connected.
Signed-off-by: Ma Ling <ling.ma@intel.com>
reviewed-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Add a debugfs file to dump the entire register range. Here we
assume that reading write-only/reserved registers won't make the chip
angry. Seems to hold true, thankfully.
Signed-off-by: Ben Gamari <bgamari.foss@gmail.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Remember to release the local reference if we fail to wait on
the rendering.
(Also whilst in the vicinity add some whitespace so that the phasing of
the operations is clearer.)
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Some i915/i945 platforms have a fairly high memory latency in certain
situations, so increase our constant a bit to avoid FIFO underruns.
The effect should be positive on other platforms as well; we'll have a
bit more insurance against a busy memory subsystem due to the extra
FIFO entries.
Fixes fdo bug #23368. Needed for 2.6.31.
Tested-by: Sven Arvidsson <sa@whiz.se>
Tested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Set accel to none, we really don't want anyone thinking
fb is an accel interface.
Pass pitch not depth to function for intel.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Initially I always meant this code to be shared, but things
ran away from me before I got to it.
This refactors the i915 and radeon kms fbdev interaction layers
out into generic helpers + driver specific pieces.
It moves all the panic/sysrq enhancements to the core file,
and stores a linked list of kernel fbs. This could possibly be
improved to only store the fb which has fbcon on it for panics
etc.
radeon retains some specific codes used for a big endian
workaround.
changes:
fix oops in v1
fix freeing path for crtc_info
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Use VBT information to determine which DDC bus to use for CRTDCC.
Fall back to GPIOA if VBT info is not available.
Signed-off-by: David Müller <d.mueller@elsoft.ch>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Tested on: 855 (David), and 945GM, 965GM, GM45, and G45 (anholt)
Several functions in the GEM kernel API used int as handle type, but
user API has it __u32 which is also the intended type.
Replace int with u32.
Signed-off-by: Pekka Paalanen <pq@iki.fi>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Based on Bspec each encoder has different sharing pipe property,
i.e. Integrated or SDVO TV both will occupy one pipe exclusively,
and sdvo-non-tv and crt are allowed to share one. The patch moves
sharing judgment into differnet output functions, and sets the right
clone bit.
This fixes both HDMI outputs choosing the same pipe.
https://bugs.freedesktop.org/show_bug.cgi?id=22247
Signed-off-by: Ma Ling <ling.ma@intel.com>
Reviewed-by : Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
After the following commit is shipped, the SDVO C detection will depend on
the SDVO_C/DP detion bit.
commit 13520b051e
Author: Kristian Høgsberg <krh@redhat.com>
Date: Fri Mar 13 15:42:14 2009 -0400
drm/i915: Read the right SDVO register when detecting SVDO/HDMI.
According to the spec we should continue to detect the SDVO_B/C based on
the SDVO_B detection bit. The new detection bit on G4X platform is for
the HDMI_C detection rather than SDVO_C detection.
https://bugs.freedesktop.org/show_bug.cgi?id=20639
Signed-off-by: Ma Ling <ling.ma@intel.com>
Acked-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Commit 0c2e39525b is not sufficient to
get fd.o bug #20115 fixed.
In addition intel_find_best_PLL() must not only rely on BIOS settings
for i9xx chips but also for i8xx, so drop the IS_I9XX() check.
Signed-off-by: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
http://bugs.freedesktop.org/show_bug.cgi?id=21417
Signed-off-by: Sean Young <sean@mess.org>
Reviewed-by: Zhao Yakui <yakui.zhao@intel.com>
Acked-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Now that we're using the scaling property in the Intel driver I noticed
that the names were a bit confusing. I've corrected them according to
our discussion on IRC and the mailing list, though I've left out
potential new additions for a new scaling property with an integer (or
two) for the scaling factor. None of the drivers implement that today,
but if someone wants to do it, I think it could be done with the
addition of a single new type and a new property to describe the
scaling factor in the X and Y directions.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Acked-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
dev_priv->saveSWF1 is a 16 element array, but this reads up to index 22,
and restored values from the wrong registers.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
We will have to add a prefix when using the macro defintion of DRM_DEBUG_KMS
/DRM_DEBUG_DRIVER/MODE. It is not convenient. We should use the DRM_NAME
as default prefix.
So remove the prefix in the macro definition of DRM_DEBUG_KMS/DRIVER/MODE.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Acked-by: Ian Romanick <ian.d.romanick@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This corresponds to a fix to UMS back in 2007. Fixes fd.o bug #20115.
Signed-off-by: Ma Ling <ling.ma@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
The patch fixed a bug on MP965-D. When VGA is connected to a DVI-I connector,
it incorrectly shows sdvo dvi as connected.
Signed-off-by: Ma Ling <ling.ma@intel.com>
[anholt: hand-resolved against previous commit and fixed up commit message]
Signed-off-by: Eric Anholt <eric@anholt.net>
Baed on Eric's idea in order to handle multiple sdvo encoders
we implement another approach to dynamically chose real one
encoder after detection, which is contrasted with patch -
drm/i915:Construct all possible sdvo outputs for sdvo encoder.
Signed-off-by: Ma Ling <ling.ma@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
In order to get best possible quality image we chose 640x480 for
NTSC, PAL and 480p, 1280x720 for 720p, 1920x1080 for 1080i/p
TV format respectively.
Signed-off-by: Ma Ling <ling.ma@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
I had one report of flicker due to FIFO underruns on 845G. Scott was
kind enough to test a few patches and report success with this one.
Looks like 845G measures FIFO size slightly differently than other
chips, and we were also clobbering the FIFO burst length. Fixing both
of those issues gives him a healthy machine again.
Note that we still only adjust plane A's watermark in the 830/845
case. If someone is willing to test we could support a bigger variety
of dual-head 830/845 configurations with a bit more code.
Fixes fdo bug #19304 (again).
Reported-by: Scott Hansen <scottandchrystie@comcast.net>
Tested-by: Scott Hansen <scottandchrystie@comcast.net>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Check FORCE_DETECT bit to be clear for the finish
of hotplug detect process. Also check possible mono
monitor which should also be marked as connected.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
This adds embedded DisplayPort support on next mobile chip which
aims to replace origin LVDS port. VBT's driver feature block has
been used to determine the type of current internal panel for eDP
or LVDS.
Currently no panel fitting support for eDP and backlight control
would be added in future.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
We should use current channel 'status' bits to clear DP aux channel's
done and error bits, instead of using the channel setting bits, that
will set send/busy bit again to initiate new transaction.
This also includes also some minor cleanup.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
During pipe DPMS off, instead of busy waiting pipe off, insert
delays during wait and don't loop after enough tries which matches
spec requirement. Also try to match DPMS on path by disable FDI TX
PLL in DPMS off. Disable PF by writing PF_WIN_SZ which really trigger
the update.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
This does VGA disable like DDX driver. SR01 bit 5 should be set
before VGA plane disable through control register, otherwise we
might get random crash and lockups.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Now the DVO timing in LVDS data entry is obtained by using the
following step:
a. get the entry size for every LVDS panel data
b. Get the LVDS fp entry for the preferred panel type
c. get the DVO timing by using entry->dvo_timing
In our driver the entry->dvo_timing is related with the size of
lvds_fp_timing. For example: the size is 46.
But it seems that the size of lvds_fp_timing varies on the differnt
platform. In such case we will get the incorrect DVO timing entry
because of the incorrect DVO offset in LVDS panel data entry.
This also removes a hack on new IGDNG to get proper DVO timing.
Calculate the DVO timing offset in LVDS data entry to get the DVO timing
a. get the DVO timing offset in the LVDS fp data entry by using the
pointer definition in LVDS data ptr
b. get the LVDS data entry
c. get the DVO timing by adding the DVO timing offset to data entry
https://bugs.freedesktop.org/show_bug.cgi?id=22787
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Tested-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
According to investigations from windows team ,hw team,
and our test results on all 4x platofrms available
(gm45, g45b, q45, g45a, g45c, g41a, and g41), we find
currently Hot plug live status and Hot plug interrupt
detection are not reliable, sometime the results from
the two approaches are contradicts. So we chose edid
detection for hdmi output.
Signed-off-by: Ma Ling <ling.ma@intel.com>
Reviewed-by: Ian Romanick <ian.d.romanick@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
If no planes are enabled, the self-refresh calculation may end up doing
a divide by zero. This patch should prevent that by making sure at
least one of the CRTCs had a valid hdisplay value.
Reported-by: Eric Anholt <eric@anholt.net>
Tested-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
If you're pushing a plane hard (i.e. you need most or all of the FIFO
entries just to cover your frame refresh latency), the watermark level
may end up being negative. So fix up the signed vs. unsigned math in
the calculation function to handle this correctly, giving all available
FIFO entries to such a configuration.
Reported-by: Eric Anholt <eric@anholt.net>
Tested-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
I discovered several bugs in the FIFO code that was recently applied.
Some of them fell into the "how did this ever work" category, since in
some cases we were using the wrong FIFO size values, and the
calculations ended up being way off.
This patch fixes all the bugs I found, and works well on my GM45, 915GM
and 855GM test machines; but as usual with these sorts of patches
broader testing is definitely requested (in particular this patch
affects 830, 845 and 865 for which I don't have test hardware).
Overall, the patch clarifies the watermark calculation function by
adding some comments and debug info, and making the variable names a
bit clearer. The "get FIFO size" portion of the code has also been
corrected, so we should be able to properly detect the FIFO allocations
for each pipe, for use in the watermark calculation.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
This motherboard thinks it has an LVDS connected, so without this
patch the screen goes blank on the connected VGA monitor. More
information (for the non-KMS case) in fd.o bug #18004.
Signed-off-by: Tormod Volden <debian.tormod@gmail.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
The 915 and 945 scanout engines can handle frame buffers up to 4096 pixels
wide. Pre-9xx hardware has an 8192 byte stride limit, and so we leave the
existing 2048 max in place.
I'm not sure why we limit the height to the same value; there's no intrinsic
hardware limit in the scanout engine.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
This patch refactors the existing error detection and collection code,
placing most of it in i915_handle_error(). Additionally, we introduce a
work queue for scheduling post-crash tasks such as generating a uevent.
Using the uevent facility, userspace should be able to capture a
post-mortem dump for diagnostics.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Ben Gamari <bgamari.foss@gmail.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Vbios will set lvds register correctly based on
current algorithm for lingle/dual Channel LVDS when
system boot, so we can accept this configuration
directly, regardless of LVDS enable status.
It fixed freedesktop.org bug #22262
Signed-off-by: Florian Mickler <florian@mickler.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
IGDNG mobile chip's LVDS data block removes panel fitting
register definition. So this fixes offset for LVDS timing
block parsing. Thanks for Michael Fu to catch this.
Signed-off-by: Zhenyu Wang <zhenyu.z.wang@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
As of 52dc7d32b8, we could leave an old
linear GTT mapping in place, so that apps trying to GTT-mapped write in
tiled data wouldn't get the fence added, and garbage would get displayed.
Signed-off-by: Eric Anholt <eric@anholt.net>
As we call unmap_mapping_range() twice in identical fashion, refactor
and attempt to explain why we need to call unmap_mapping_range().
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
In KMS mode we now use the normal mode-setting paths to set the modes
back to the current configuration, so we don't need to also run the more
limited non-KMS implementation of modesetting for resume.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
This is seen on some G41 systems, where the BIOS will consume all but
a few KB of the aperture. This should be bad for all operating systems, as
it means that the OS can't dynamically manage memory between graphics and
the rest of the system, and OSes that did static memory management
statically add memory in addition to the BIOS allocation anyway. So, instead
of working around it, just fail out verbosely.
fd.o bug #21574
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Ian Romanick <ian.d.romanick@intel.com>
On some boxes the mobile chipset is used and there is no LVDS device. In such
case we had better not initialize the LVDS output device so that one pipe can
be used for other output device. For example: E-TOP.
But unfortunately the LVDS device is still initialized on the boxes based on
mobile chipset in KMS mode. It brings that this pipe occupied by LVDS can't be
used for other output device.
After checking the acpidump we find that there is no LID device on such boxes.
In such case we can use the LID device to decide whether the LVDS device should
be initialized.
If there is no LID device, we can think that there is no LVDS device. It is
unnecessary to initialize the LVDS output device.
If there exists the LID device, it will continue the current flowchart.
Maybe on some boxes there is no LVDS device but the LID device is found. In
such case it should be added to the quirk list.
http://bugs.freedesktop.org/show_bug.cgi?id=21496http://bugs.freedesktop.org/show_bug.cgi?id=21856http://bugs.freedesktop.org/show_bug.cgi?id=21127
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[anholt: squashed in style fixups]
Signed-off-by: Eric Anholt <eric@anholt.net>
Make this consistent with the unlock statement. Also fix a
minor typo in debugfs formatting
Signed-off-by: Ben Gamari <bgamari.foss@gmail.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
This is quite useful for verifying that objects are actually mapped when
they need to be.
Signed-off-by: Ben Gamari <bgamari.foss@gmail.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
This wasn't even used as far as I could tell and will only confuse
people (like me).
Signed-off-by: Ben Gamari <bgamari.foss@gmail.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Usually crt mainly get modes via GPIOA ports.
However on G4X platform we need to probe possible
ports for DVI-I, which could be wired to GPIOD,
then fetch our desired EDID, i.e on DG45ID platform
we successfully fetch EDID by GPIOD port.
It fixed freedesktop.org bug #21084
Signed-off-by: Ma Ling <ling.ma@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
For some reason, the DP clocks were based off a 100MHz reference instead of
the standard 96MHz reference. This caused some DP monitors to fail to lock
to the signal.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Convert many printk calls to DRM_DEBUG calls to reduce kernel log noise
for normal activities. Switch other printk calls to DRM_ERROR or DRM_INFO.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
We are seeing compilation failures on i386 in some environments due
to an undefined reference as below:
ERROR: "__udivdi3" [drivers/gpu/drm/i915/i915.ko] undefined!
This is generated due to a raw 64 bit divide in the i915 driver. Fix up
this raw divide.
Signed-off-by: Andy Whitcroft <apw@canonical.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Currently we implemented basic sdvo lvds function,
But except for sdvo lvds fixed mode, we can not switch
to other modes, otherwise display get black. The patch
handle three operations to enable sdvo lvds. At first
duplicate sdvo fixed mode for adjustment, then according
to fixed mode line valid all modes, at last adjust input
mode to fit our requirement.
Acked by Li Peng <peng.li@linux.intel.com>
Signed-off-by: Ma Ling <ling.ma@intel.com>
Reviewed-by: Ian Romanick <idr@freedesktop.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
All 8xx class chips have the 66/48 split, not just 855.
Signed-off-by: Ma Ling <ling.ma@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
This patch from jbarnes and myself adds FIFO watermark control to the
driver. This is needed for both power saving features on new platforms
with the so-called "big FIFO" and for controlling FIFO allocation
between pipes in multi-head configurations.
It's also necessary infrastructure to support things like framebuffer
compression and configuration supportability checks (i.e. checking a
configuration against available bandwidth).
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
This patch enables error detection by enabling several types of error
interrupts. When an error interrupt is received, the interrupt
handler captures the error state; hopefully resulting in an accurate
set of error data (error type, active head pointer, etc.). The new
record is then available from sysfs. The current code will also dump
the error state to the system log.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (28 commits)
drm: remove unused #include <linux/version.h>'s
drm/radeon: fix driver initialization order so radeon kms can be builtin
drm: Fix shifts which were miscalculated when converting from bitfields.
drm/radeon: Clear surface registers at initialization time.
drm/radeon: Don't initialize acceleration related fields of struct fb_info.
drm/radeon: fix radeon kms framebuffer device
drm/i915: initialize fence registers to zero when loading GEM
drm/i915: Fix HDMI regression introduced in new chipset support
drm/i915: fix LFP data fetch
drm/i915: set TV detection mode when tv is already connected
drm/i915: Catch up to obj_priv->page_list rename in disabled debug code.
drm/i915: Fix size_t handling in off-by-default debug printfs
drm/i915: Don't change the blank/sync width when calculating scaled modes
drm/i915: Add support for changing LVDS panel fitting using an output property.
drm/i915: correct suspend/resume ordering
drm/i915: Add missing dependency on Intel AGP support.
drm/i915: Generate 2MHz clock for display port aux channel I/O. Retry I/O.
drm/i915: Clarify error returns from display port aux channel I/O
drm/i915: Add CLKCFG register definition
drm/i915: Split array of DAC limits into separate structures.
...
Sometimes both acpi video and i915 driver are compiled as modules.
And there exists the strict dependency between the two drivers.
The acpi video bus will be unloaded in course of unloading the i915 driver.
If we unload the acpi video driver, then the kernel oops will be triggered.
Add the reference count to avoid unloading the ACPI video bus twice.
The reference count should be checked before unregistering the acpi video bus.
If the reference count is already zero, it won't unregister it again.
And after the acpi video bus is already unregistered, the reference count
will be set to zero.
http://bugzilla.kernel.org/show_bug.cgi?id=13396
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Unitialized fence register could leads to corrupted display. Problem
encountered on MacBooks (revision 1 and 2), directly booting from EFI
or through BIOS emulation.
(bug #21710 at freedestop.org)
Signed-off-by: Grégoire Henry <henry@pps.jussieu.fr>
Signed-off-by: Eric Anholt <eric@anholt.net>
Remove wrongly added NULL_PACKETS_DURING_VSYNC setting for HDMI.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Apparently the proper way to do this is to use the LFP data pointer
block to figure out the LFP data block entry size, then use that plus
the panel index to calculate an offset into the LFP data block array.
Similar fix has already been pushed to the 2D driver to fix fdo bug
applied to the VBIOS reader, and things look sane).
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
We used load_detect_temp flag to determine whether to set tv to the test
mode. However if the TV already has a mode set, we still need to set the
test mode to determine connection. This results in blinking, but there is
no other reliable way to determine TV connection.
freedesktop.org bug #22035
Signed-off-by: Ma Ling <ling.ma@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Also, use the border instead of border minus one.
At the same time, make sure the horizontal border and hsync are even for
the LVDS that works in dual-channel mode. So both horizontal border and hsync
start are also changed to be even, even for the LVDS in single-channel mode.
https://bugs.freedesktop.org/show_bug.cgi?id=20951
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Previously the driver would always scale the chosen video mode to fill the
panel. This adds 1:1 and maintain-aspect-ratio scaling modes.
v2: the drm_calloc/drm_free is replaced by kzalloc/kfree based
on Eric's suggestion.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
We need to save register state *after* idling GEM, clearing the ring,
and uninstalling the IRQ handler, or we might end up saving bogus
fence regs, for one. Our restore ordering should already be correct,
since we do GEM, ring and IRQ init after restoring the last register
state, which prevents us from clobbering things.
I put this together to potentially address a bug, but I haven't heard
back if it fixes it yet. However I think it stands on its own, so I'm
sending it in.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
In theory now that the AGP subsystem is using struct page, we should
have on problems enabling GEM on PAE systems.
Signed-off-by: Dave Airlie <airlied@redhat.com>
The display port aux channel clock is taken from the hrawclk value, which is
provided to the chip as the FSB frequency (as far as I can determine). The
strapping values for that are available in the CLKCFG register, now used to
select an appropriate divider to generate a 2MHz clock.
In addition, the DisplayPort spec requires that each aux channel I/O be
retried 'at least 3 times' in case the sink is idle when the first request
comes in.
Signed-off-by: Keith Packard <keithp@keithp.com>
The array of DAC limits was only ever referenced with #defined constant
offsets, and keeping those #define values in sync with the array itself was a
nuisance. This will make future changes to the set of DAC limits less
error-prone.
Signed-off-by: Keith Packard <keithp@keithp.com>
Eliminate the copy of i2c_bus in sdvo_priv.
Eliminate local copies of i2c_bus and ddcbus.
Eliminate unused settings of slave_addr.
Signed-off-by: Keith Packard <keithp@keithp.com>
The existing API passed around intel_i2c_chan pointers, which are dependent
on the i2c bit-banging algo. This precluded the driver from using outputs
which use a different algo. Switching to the more general i2c_adpater allows
the driver to support non bit-banging DDC.
This also required moving the slave address into the output private
structures.
Signed-off-by: Keith Packard <keithp@keithp.com>
Some machines say 'Apple Inc.' while others say 'Apple Computer, Inc'.
Switch the test to just look for 'Apple' instead.
Signed-off-by: Keith Packard <keithp@keithp.com>
HDMI and DVI both require DDC/EDID on monitors, so use
that to know when a monitor is connected as the hot-plug
pins are shared with SDVO and DisplayPort
Signed-off-by: Keith Packard <keithp@keithp.com>
It hasn't been used in ages, and having the user tell your how much
memory is being freed at free time is a recipe for disaster even if it
was ever used.
Signed-off-by: Eric Anholt <eric@anholt.net>
The fence register value also depends upon the stride of the object, so we
need to clear the fence if that is changed as well.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[anholt: Added 8xx and 965 paths, and renamed the confusing
i915_gem_object_tiling_ok function to i915_gem_object_fence_offset_ok]
Signed-off-by: Eric Anholt <eric@anholt.net>
With the work by Jesse Barnes to eliminate allocation of fences during
execbuffer, it becomes possible to write to the scan-out buffer with it
never acquiring a fence (simply by only ever writing to the object using
tiled GPU commands and never writing to it via the GTT). So for pre-i965
chipsets which require fenced access for tiled scan-out buffers, we need
to obtain a fence register.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
After performing an operation over the page list for a buffer retrieved by
i915_gem_object_get_pages() the pages need to be returned with
i915_gem_object_put_pages(). This was not being observed for the phys
objects which were thus leaking references to their backing pages.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
CC: Dave Airlie <airlied@gmail.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
While sifting through the inteldrmfb code trying to solve #22040 I found that
the fb restore path doesn't check the return value of
drm_crtc_helper_set_config(), which seems to have all sorts of potential
failure modes. We should warn someone if one of these is triggered.
Signed-Off-By: Ben Gamari <bgamari.foss@gmail.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[anholt: hand-applied, failures are mine]
Signed-off-by: Eric Anholt <eric@anholt.net>
With KMS we have ran into an issue where we really want the KMS fb driver
to be the one running the console, so panics etc can be shown by switching
out of X etc.
However with vesafb/efifb built-in, we end up with those on fb0 and the
KMS fb driver on fb1, driving the same piece of hw, so this adds an fb
info flag to denote a firmware fbdev, and adds a new aperture base/size
range which can be compared when the hw drivers are installed to see if
there is a conflict with a firmware driver, and if there is the firmware
driver is unregistered and the hw driver takes over.
It uses new aperture_base/size members instead of comparing on the fix
smem_start/length, as smem_start/length might for example only cover the
first 1MB of the PCI aperture, and we could allocate the kms fb from 8MB
into the aperture, thus they would never overlap.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Dave Airlie <airlied@redhat.com>
Acked-by: Peter Jones <pjones@redhat.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (50 commits)
drm: include kernel list header file in hashtab header
drm: Export hash table functionality.
drm: Split out the mm declarations in a separate header. Add atomic operations.
drm/radeon: add support for RV790.
drm/radeon: add rv740 drm support.
drm_calloc_large: check right size, check integer overflow, use GFP_ZERO
drm: Eliminate magic I2C frobbing when reading EDID
drm/i915: duplicate desired mode for use by fbcon.
drm/via: vfree() no need checking before calling it
drm: Replace DRM_DEBUG with DRM_DEBUG_DRIVER in i915 driver
drm: Replace DRM_DEBUG with DRM_DEBUG_MODE in drm_mode
drm/i915: Replace DRM_DEBUG with DRM_DEBUG_KMS in intel_sdvo
drm/i915: replace DRM_DEBUG with DRM_DEBUG_KMS in intel_lvds
drm: add separate drm debugging levels
radeon: remove _DRM_DRIVER from the preadded sarea map
drm: don't associate _DRM_DRIVER maps with a master
drm: simplify kcalloc() call to kzalloc().
intelfb: fix spelling of "CLOCK"
drm: fix LOCK_TEST_WITH_RETURN macro
drm/i915: Hook connector to encoder during load detection (fixes tv/vga detect)
...
Replace the DRM_DEBUG with the DRM_DEBUG_DRIVER to print the debug info
in i915 driver.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Use the DRM_DEBUG_KMS/DEBUG_LOG_KMS to print the debug info for
SDVO device.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Use the DRM_DEBUG_KMS macro definition to print the debug info for
the LVDS.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Pavel Roskin <proski@gnu.org>
Cc: Eric Anholt <eric@anholt.net>
Cc: Dave Airlie <airlied@linux.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
With the DRM-driven DPMS code, encoders are considered idle unless a
connector is hooked to them, so mode setting is skipped. This makes load
detection fail as none of the hardware is enabled.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
To differentiate between encountering an out-of-memory error with running
out of space in the aperture, use ENOSPC for the later.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Ensure that the drm_vblank_pre_modeset() is always balanced by
drm_vblank_post_modeset() within intel_crtc_mode_set().
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
The batch buffer may be shared with another read buffer, so we should not
ignore any previously set domains, but just or in the command domain (and
check that the buffer is not writable).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
By sending a broken execbuffer (its length was not suitably aligned) I
triggered an operation upon a freed object. The invalid alignment was
discovered after updating the write_domain on the object but before the
object was placed on the active queue. So during the unwind process
following the error, the now freed object attempts to flush its
non-existent, but outstanding, GPU writes causing this use-after-free.
[drm:i915_dispatch_gem_execbuffer] *ERROR* alignment
[drm:i915_gem_execbuffer] *ERROR* dispatch failed -22
WARNING: at lib/kref.c:43 warn_slowpath_null+0x10/0x15()
Modules linked in:
Pid: 4552, comm: lt-csi-drm Not tainted 2.6.30-rc6 #423
Call Trace:
[<c0119ef3>] warn_slowpath_fmt+0x57/0x6d
[<c014de24>] ? get_pageblock_migratetype+0x18/0x1e
[<c014e8fd>] ? free_hot_page+0xa/0xc
[<c014e915>] ? __free_pages+0x16/0x1f
[<c0153ebf>] ? shmem_truncate_range+0x63e/0x656
[<c015fb2f>] ? slob_page_alloc+0x146/0x1c8
[<c0119f19>] warn_slowpath_null+0x10/0x15
[<c01f55f2>] kref_get+0x1b/0x21
[<c02605db>] i915_gem_object_move_to_active+0x1f/0x56
[<c0261302>] i915_add_request+0x156/0x19a
[<c026136e>] i915_gem_object_flush_gpu_write_domain+0x28/0x3f
[<c0261eca>] i915_gem_object_unbind+0x4a/0x124
[<c0261fd7>] i915_gem_free_object+0x33/0x9b
[<c0250d6b>] drm_gem_object_free+0x28/0x4a
[<c0250d43>] ? drm_gem_object_free+0x0/0x4a
[<c01f55ce>] kref_put+0x38/0x41
[<c0250cbf>] drm_gem_object_unreference+0x11/0x13
[<c0250d06>] drm_gem_object_handle_unreference+0x1e/0x21
[<c0250d13>] drm_gem_object_release_handle+0xa/0xe
[<c01f3e6b>] idr_for_each+0x5f/0x98
[<c0250d09>] ? drm_gem_object_release_handle+0x0/0xe
[<c0250daf>] drm_gem_release+0x22/0x34
[<c025046f>] drm_release+0x1e8/0x3c4
[<c0162d25>] __fput+0xaf/0x146
[<c0162dce>] fput+0x12/0x14
[<c01605ef>] filp_close+0x48/0x52
[<c011b182>] put_files_struct+0x57/0x9b
[<c011b1e4>] exit_files+0x1e/0x20
[<c011c6b6>] do_exit+0x16d/0x511
[<c03704ab>] ? __schedule+0x3d4/0x3e5
[<c0103f0d>] ? handle_irq+0xd/0x69
[<c011caa7>] do_group_exit+0x4d/0x73
[<c011cae0>] sys_exit_group+0x13/0x17
[<c010268c>] sysenter_do_call+0x12/0x2b
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Update interrupt handling methods for IGDNG with new registers
for display and graphics interrupt functions. As we won't use
irq-based vblank sync in dri2, so display interrupt on new chip
will be used for hotplug only in future.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Using the new PNP resource checking code, this patch allows the i915
driver to allocate MCHBAR space if needed and use the BAR to determine
current memory settings.
[apw@canonical.com: moved to the new generic PNP resource interface]
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Andy Whitcroft <apw@canonical.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
failure to update-index after git-am --reject to hand-apply
Signed-off-by: Eric Anholt <eric@anholt.net>
The sysrq functions are executed in hardirq context, so we shouldn't be
calling sleeping functions from them, like mutex_locks or memory
allocations.
Fix up the i915 sysrq handler to avoid this.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
All G4x and newer chips use the new style frame count register, with a
full 32 bit frame count. Update the code to reflect this.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Fix a FIXME in the intel LVDS bring-up code, adding the appropriate
blacklist entry for the AOpen Mini PC, courtesy of a dmidecode
dump from Florian Demmer.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
CC: Florian Demmer <florian@demmer.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
The general definition block contains the child device tables, which include
the SDVO device info. For example: device slave address, device dvo port,
device type.
We will get the info of SDVO device by parsing the general definition blocks.
Only when a valid slave address is found, it is regarded as the SDVO device.
And the info of DVO port and slave address is recorded.
http://bugs.freedesktop.org/show_bug.cgi?id=20429
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
This adds the register definitions for the display port enable register
along with those for the GMCH and Link M/N ratios required to drive display
port outputs.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
We can safely assume that cursor addresses will not extend beyond the
addressable screen dimensions; setting the additional bits is harmless in
any case.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
We detect TV connect status by setting DAC voltage level override
values as 0.7 voltage for DAC_A/B/C. The corresponding 2-bits shold be 0x2,
In order correctly to set last bit as 0, at first we must clean it.
It fixed freedesktop.org bug #21204
Signed-off-by: Ma Ling <ling.ma@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
This adds kernel mode setting on IGDNG with VGA output support.
Note that suspend/resume doesn't work yet.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Disable OpRegion support for now until verified on new chipsets.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
[anholt: dropped drm_pciids.h hunk to avoid loading an incomplete driver]
Signed-off-by: Eric Anholt <eric@anholt.net>
keithp didn't like the original 20ms plan because a cooperative client could
be starved by an uncooperative client. There may even have been problems
with cooperative clients versus cooperative clients. So keithp changed
throttle to just wait for the second to last seqno emitted by that client.
It worked well, until we started getting more round-trips to the server
due to DRI2 -- the server throttles in BlockHandler, and so if you did more
than one round trip after finishing your frame, you'd end up unintentionally
syncing to the swap.
Fix this by keeping track of the client's requests, so the client can wait
when it has an outstanding request over 20ms old. This should have
non-starving behavior, good behavior in the presence of restarts, and less
waiting. Improves high-settings openarena performance on my GM45 by 50%.
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This may fix cursor corruption in X on resume, which would persist until
the cursor was hidden and then shown again.
V2: Also include the cursor control regs.
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This could be triggered by a gtt mapping fault on 965 that decides to
remove the fence from another object that happens to be active currently.
Since the other object doesn't rely on the fence reg for its execution, we
don't wait for it to finish. We'll soon be not waiting on 915 most of the
time as well, so just drop the BUG_ON.
Signed-off-by: Eric Anholt <eric@anholt.net>
intel_no_lvds[] does not require __initdata as it is used only by
void intel_lvds_init(struct drm_device *dev).
Signed-off-by: Jaswinder Singh Rajput <jaswinder@kernel.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Making the drm_crtc.c code recognize the DPMS property and invoke the
connector->dpms function doesn't remove any capability from the driver while
reducing code duplication.
That just highlighted the problem with the existing DPMS functions which
could turn off the connector, but failed to turn off any relevant crtcs. The
new drm_helper_connector_dpms function manages all of that, using the
drm_helper-specific crtc and encoder dpms functions, automatically computing
the appropriate DPMS level for each object in the system.
This fixes the current troubles in the i915 driver which left PLLs, pipes
and planes running while in DPMS_OFF mode or even while they were unused.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
allocating devname in the i915 driver was a hack originally and I
forgot to figure out how to do this properly back then.
So this is the cleaner version that just picks devname or driver name
in the irq code.
It removes the devname allocs from the i915 driver.
Signed-off-by: Dave Airlie <airlied@redhat.com>
When a GEM object is evicted from the GTT we set it to the CPU domain,
as it might get swapped in and out or ever mmapped regularly. If the
object is mmapped through the GTT it can still get evicted in this way
by other objects requiring GTT space. When the GTT mapping is touched
again we fault it back into the GTT, but fail to set it back to the
GTT domain. This means we fail to flush any cached CPU writes to the
pages backing the object which will then happen "eventually", typically
after we write to the page through the uncached GTT mapping.
[anholt: Note that userland does do a set_domain(GTT, GTT) when starting
to access the GTT mapping. That covers getting the existing mapping of the
object synchronized if it's bound to the GTT. But set_domain(GTT, GTT)
doesn't do anything if the object is currently unbound. This fix covers the
transition to being bound for GTT mapping.]
Fixes glyph and other pixmap corruption during swapping. fd.o bug #21790
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
On the 865, but not the 855, the clflush we do appears to not actually make
it out to the hardware all the time. An easy way to safely reproduce was
X -retro, which would show that some of the blits involved in drawing the
lovely root weave didn't make it out to the hardware. Those blits are 32
bytes each, and 1-2 would be missing at various points around the screen.
Other experimentation (doing more clflush, doing more AGP chipset flush,
poking at some more device registers to maybe trigger more flushing) didn't
help. krh came up with the wbinvd as a way to successfully get all those
blits to appear.
Signed-off-by: Eric Anholt <eric@anholt.net>
The pitch field is an exponent on pre-965, so we were rejecting buffers
on 8xx that we shouldn't have. 915 got lucky in that the largest legal
value happened to match (8KB / 512 = 0x10), but 8xx has a smaller tile width.
Additionally, we programmed that bad value into the register on 8xx, so the
only pitch that would work correctly was 4096 (512-1023 pixels), while others
would probably give bad rendering or hangs.
Signed-off-by: Eric Anholt <eric@anholt.net>
fd.o bug #20473.
Two approaches for VGA detections: hot plug detection for 945G onwards
and load pipe detection for Pre-945G. Load pipe detection will get one free
pipe, set border color as red and blue, then check CRT status by
swf register. This is a sync-up with the 2D driver.
Signed-off-by: Ma Ling <ling.ma@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Previously, we would set the control bus switch before calls were made
to request EDID information over DDC. But recently the DDC code started
doing multiple I2C transfers to get the EDID extensions as well. This
tripped up SDVO, because the control bus switch is only in effect until
the next STOP after a START. By doing our own algo, we can wrap each i2c
transaction on the DDC I2C bus with the control bus switch it requires.
freedesktop.org bug #21042
Signed-off-by: Ma Ling <ling.ma@intel.com>
[anholt: Hand application for conflict, fixed error path]
Signed-off-by: Eric Anholt <eric@anholt.net>
drm_connector_init sets both the connector type and the connector type_id
on the newly initialised connector. As the connector type_id is coupled to
the connector type, the connector type cannot simply be modified on an
initialised connector.
This patch changes the order of operations on intel_sdvo_init so that the
type is determined before the connector is intialised.
This fixes a bug whereby the name card0-VGA-1 would be allocted to both a
CRT and an SDVO connector since the SDVO connector would be initialised
with type 'unknown' and hence have its type_id assigned from the wrong pool.
Signed-off-by: Jonas Bonn <jonas@southpole.se>
Signed-off-by: Eric Anholt <eric@anholt.net>
Some new SDVO LVDS hardware doesn't have DDC available, and this should
fix the display on it.
Signed-off-by: Ma Ling <ling.ma@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
For some reason we never added 8xx desktop cursor support to the
kernel. This patch fixes that.
[krh: Also set the size on pre-i915 hw.]
Tested-by: Kristian Høgsberg <krh@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
For awhile now, many of the GEM code paths have allocated page or
object arrays with the slab allocator. This is nice and fast, but
won't work well if memory is fragmented, since the slab allocator works
with physically contiguous memory (i.e. order > 2 allocations are
likely to fail fairly early after booting and doing some work).
This patch works around the issue by falling back to vmalloc for
>PAGE_SIZE allocations. This is ugly, but much less work than chaining
a bunch of pages together by hand (suprisingly there's not a bunch of
generic kernel helpers for this yet afaik). vmalloc space is somewhat
precious on 32 bit kernels, but our allocations shouldn't be big enough
to cause problems, though they're routinely more than a page.
Note that this patch doesn't address the unchecked
alloc-based-on-ioctl-args in GEM; that needs to be fixed in a separate
patch.
Also, I've deliberately ignored the DRM's "area" junk. I don't think
anyone actually uses it anymore and I'm hoping it gets ripped out soon.
[Updated: removed size arg to new free function. We could unify the
free functions as well once the DRM mem tracking is ripped out.]
fd.o bug #20152 (part 1/3)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
* 'drm-intel-next' of git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel:
drm/i915: Add new GET_PIPE_FROM_CRTC_ID ioctl.
drm/i915: Set HDMI hot plug interrupt enable for only the output in question.
drm/i915: Include 965GME pci ID in IS_I965GM(dev) to match UMS.
drm/i915: Use the GM45 VGA hotplug workaround on G45 as well.
drm/i915: ignore LVDS on intel graphics systems that lie about having it
drm/i915: sanity check IER at wait_request time
drm/i915: workaround IGD i2c bus issue in kernel side (v2)
drm/i915: Don't allow binding objects into the last page of the aperture.
drm/i915: save/restore fence registers across suspend/resume
drm/i915: x86 always has writeq. Add I915_READ64 for symmetry.
Commit 79e539453b introduced a
regression where you cannot use sysrq 'g' to enter kgdb. The solution
is to move the intel fb sysrq over to V for video instead of G for
graphics. The SMP VOYAGER code to register for the sysrq-v is not
anywhere to be found in the mainline kernel, so the comments in the
code were cleaned up as well.
This patch also cleans up the sysrq definitions for kgdb to make it
generic for the kernel debugger, such that the sysrq 'g' can be used
in the future to enter a gdbstub or another kernel debugger.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
This allows userlevel code to discover the pipe number corresponding
to a given CRTC ID. This is necessary for doing pipe-specific
operations such as waiting for vblank on a given CRTC. Failure to use
the right pipe mapping can result in GPU hangs, or at least failure
to actually sync to vblank.
Signed-off-by: Carl Worth <cworth@cworth.org>
[anholt: Style touchups from review]
Signed-off-by: Eric Anholt <eric@anholt.net>
We detect HDMI output connection status by writing to HOT Plug Interrupt
Detect Enable bit in PORT_HOTPLUG_EN. The behavior will generate a specified
interrupt, which is caught by audio driver, but during one detection driver
set all Detect Enable bits of HDMIB, HDMIC HDMID, and generate wrong
interrupt signals for current output, according to the signals audio driver
misunderstand device status. The patch intends to handle corresponding
output precisely.
It fixed freedesktop.org bug #21371
Signed-off-by: Ma Ling <ling.ma@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
It fixed bug #21659
Signed-off-by: Ma Ling <ling.ma@intel.com>
[anholt: hand-applied because git-am is too picky]
Signed-off-by: Eric Anholt <eric@anholt.net>
Although spec say CRT_HOTPLUG_ACTIVATION_PERIOD_64 is only useful for
mobile platform, it is also required to detect vga on G4x desktops correctly.
Tested on G45/G43/Q45 platforms with no regressions.
It fixed freedesktop.org bug #21120 and part of bug #21210
Signed-off-by: Ma Ling <ling.ma@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
There are a number of small form factor desktop systems with Intel mobile
graphics chips that lie and say they have an LVDS. With kernel mode-setting,
this becomes a problem, and makes native resolution boot go haywire -- for
example, my Dell Studio Hybrid, hooked to a 1920x1080 display claims to
have a 1024x768 LVDS, and the resulting graphical boot on the 1920x1080
display uses only the top left 1024x768, and auto-configured X will end
up only 1024x768 as well. With this change, graphical boot and X
both do 1920x1080 as expected.
Note that we're simply embracing and extending the early bail-out code
in place for the Mac Mini here. The xorg intel driver uses pci subsystem
device and vendor id for matching, while we're using dmi lookups here.
The MSI addition is courtesy of and tested by Bill Nottingham.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Tested-by: Bill Nottingham <notting@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
We might sleep here anyway so I hope an extra uncached read is ok to
add.
In #20896 we found that vbetool clobbers the IER. In KMS mode this is
particularly bad since we don't set the interrupt regs late (in
EnterVT), so we'd fail to get *any* interrupts at all after X started
(since some distros have scripts that call vbetool at X startup
apparently).
So this patch checks IER at wait_request time, and re-enables
interrupts if it's been clobbered. In a proper config this check
should never be triggered.
This is really a distro issue, but having a sanity check is nice, as
long as it doesn't have a real performance hit.
Tested-by: Mateusz Kaduk <mateusz.kaduk@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[anholt: Moved the check inside of the sleeping case to avoid perf cost]
Signed-off-by: Eric Anholt <eric@anholt.net>
Zhenyu Wang
Chris Wilson
Jesse Barnes
Andy Lutomirski
Zhao Yakui
Shaohua Li
Linus Torvalds
Dave Airlie
Adam Jackson
Eric Anholt
Brian Rogers
Dave Airlie
Joe Perches
Jaswinder Singh Rajput
Ben Gamari
Li Peng
Li Peng
Fabian Henze
Keith Packard
Daniel Vetter
Kyle McMartin
Ma Ling
David Müller (ELSOFT AG)
Pekka Paalanen
Roel Kluin
Bruno Prémont
Sean Young
Frans Pop
Tormod Volden
Florian Mickler
Zhenyu Wang
Andy Whitcroft
Len Brown
Grégoire Henry
Krzysztof Halasa
Pavel Roskin
Michael Cousin
Jesse Barnes
Jarod Wilson
Kristian Høgsberg
Jonas Bonn
Jason Wessel
Carl Worth