PowerPC 750CL has high BATs. The patch below adds a CPU_FTRS_750CL that
includes that. Without it, the original firmware mappings in the high BATs
aren't cleared which continue to override the linux translations.
It also adds CPU_FTR_COMMON to CPU_FTRS_750GX for completeness.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The of_iomap function maps memory for a given
device_node and returns a pointer to that memory.
This is used at some places, so it makes sense to
a seperate function.
Signed-off-by: Christian Krafft <krafft@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
This patch adds code to deal with conversion of
logical cpu to cbe nodes. It removes code that
assummed there were two logical CPUs per CBE.
Signed-off-by: Christian Krafft <krafft@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Until now, we have always entered the spu page fault handler
with a mutex for the spu context held. This has multiple
bad side-effects:
- it becomes impossible to suspend the context during
page faults
- if an spu program attempts to access its own mmio
areas through DMA, we get an immediate livelock when
the nopage function tries to acquire the same mutex
This patch makes the page fault logic operate on a
struct spu_context instead of a struct spu, and moves it
from spu_base.c to a new file fault.c inside of spufs.
We now also need to copy the dar and dsisr contents
of the last fault into the saved context to have it
accessible in case we schedule out the context before
activating the page fault handler.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Here's an implementation of DEBUG_PAGEALLOC for ppc32. It disables BAT
mapping and is only tested with Hash table based processor though it
shouldn't be too hard to adapt it to others.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
arch/powerpc/Kconfig.debug | 9 ++++++
arch/powerpc/mm/init_32.c | 4 +++
arch/powerpc/mm/pgtable_32.c | 52 +++++++++++++++++++++++++++++++++++++++
arch/powerpc/mm/ppc_mmu_32.c | 4 ++-
include/asm-powerpc/cacheflush.h | 6 ++++
5 files changed, 74 insertions(+), 1 deletion(-)
Signed-off-by: Paul Mackerras <paulus@samba.org>
The current tlb flush code on powerpc 64 bits has a subtle race since we
lost the page table lock due to the possible faulting in of new PTEs
after a previous one has been removed but before the corresponding hash
entry has been evicted, which can leads to all sort of fatal problems.
This patch reworks the batch code completely. It doesn't use the mmu_gather
stuff anymore. Instead, we use the lazy mmu hooks that were added by the
paravirt code. They have the nice property that the enter/leave lazy mmu
mode pair is always fully contained by the PTE lock for a given range
of PTEs. Thus we can guarantee that all batches are flushed on a given
CPU before it drops that lock.
We also generalize batching for any PTE update that require a flush.
Batching is now enabled on a CPU by arch_enter_lazy_mmu_mode() and
disabled by arch_leave_lazy_mmu_mode(). The code epects that this is
always contained within a PTE lock section so no preemption can happen
and no PTE insertion in that range from another CPU. When batching
is enabled on a CPU, every PTE updates that need a hash flush will
use the batch for that flush.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Those are needed by things like alignment exception fixup handlers
since those can now be triggered by copy_tofrom_user_inatomic.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Some drivers have resources that they want to be able to map into
userspace that are 4k in size. On a kernel configured with 64k pages
we currently end up mapping the 4k we want plus another 60k of
physical address space, which could contain anything. This can
introduce security problems, for example in the case of an infiniband
adaptor where the other 60k could contain registers that some other
program is using for its communications.
This patch adds a new function, remap_4k_pfn, which drivers can use to
map a single 4k page to userspace regardless of whether the kernel is
using a 4k or a 64k page size. Like remap_pfn_range, it would
typically be called in a driver's mmap function. It only maps a
single 4k page, which on a 64k page kernel appears replicated 16 times
throughout a 64k page. On a 4k page kernel it reduces to a call to
remap_pfn_range.
The way this works on a 64k kernel is that a new bit, _PAGE_4K_PFN,
gets set on the linux PTE. This alters the way that __hash_page_4K
computes the real address to put in the HPTE. The RPN field of the
linux PTE becomes the 4k RPN directly rather than being interpreted as
a 64k RPN. Since the RPN field is 32 bits, this means that physical
addresses being mapped with remap_4k_pfn have to be below 2^44,
i.e. 0x100000000000.
The patch also factors out the code in arch/powerpc/mm/hash_utils_64.c
that deals with demoting a process to use 4k pages into one function
that gets called in the various different places where we need to do
that. There were some discrepancies between exactly what was done in
the various places, such as a call to spu_flush_all_slbs in one case
but not in others.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This is more consistent and gets us closer to the Sparc code.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This is more consistent and gets us closer to the Sparc code.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This is more consistent and gets us closer to the Sparc code.
We add a device_is_compatible define for compatibility during the
change over.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This is more consistent and gets us closer to the Sparc code.
We add a get_property define for compatibility during the change over.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
mtocrf is a faster single-field mtcrf (move to condition register
fields) instruction available in POWER4 and later processors. It can
make quite a difference in performance on some implementations, so use
it for CONFIG_POWER4_ONLY builds.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This common uevent handler allow the several bus types based on
of_device to generate the uevent properly and avoiding
code duplication.
This handlers take a struct device as argument and can therefore
be used as the uevent call directly if no special treatment is
needed for the bus.
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
* master.kernel.org:/pub/scm/linux/kernel/git/bart/ide-2.6:
ide: add "optical" to sysfs "media" attribute
ide: ugly messages trying to open CD drive with no media present
ide: correctly prevent IDE timer expiry function to run if request was already handled
It is possible for the timer expiry function to run even though the
request has already been handled: ide_timer_expiry() only checks that
the handler is not NULL, but it is possible that we have handled a
request (thus clearing the handler) and then started a new request
(thus starting the timer again, and setting a handler).
A simple way to exhibit this is to set the DMA timeout to 1 jiffy and
run dd: The kernel will panic after a few minutes because
ide_timer_expiry() tries to add a timer when it's already active.
To fix this, we simply add a request generation count that gets
incremented at every interrupt, and check in ide_timer_expiry() that
we have not already handled a new interrupt before running the expiry
function.
Signed-off-by: Suleiman Souhlal <suleiman@google.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Since lazy MMU batching mode still allows interrupts to enter, it is
possible for interrupt handlers to try to use kmap_atomic, which fails when
lazy mode is active, since the PTE update to highmem will be delayed. The
best workaround is to issue an explicit flush in kmap_atomic_functions
case; this is the only way nested PTE updates can happen in the interrupt
handler.
Thanks to Jeremy Fitzhardinge for noting the bug and suggestions on a fix.
This patch gets reverted again when we start 2.6.22 and the bug gets fixed
differently.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Cc: Andi Kleen <ak@muc.de>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Soeren Sonnenburg reported that upon resume he is getting
this backtrace:
[<c0119637>] smp_apic_timer_interrupt+0x57/0x90
[<c0142d30>] retrigger_next_event+0x0/0xb0
[<c0104d30>] apic_timer_interrupt+0x28/0x30
[<c0142d30>] retrigger_next_event+0x0/0xb0
[<c0140068>] __kfifo_put+0x8/0x90
[<c0130fe5>] on_each_cpu+0x35/0x60
[<c0143538>] clock_was_set+0x18/0x20
[<c0135cdc>] timekeeping_resume+0x7c/0xa0
[<c02aabe1>] __sysdev_resume+0x11/0x80
[<c02ab0c7>] sysdev_resume+0x47/0x80
[<c02b0b05>] device_power_up+0x5/0x10
it turns out that on resume we mistakenly re-enable interrupts too
early. Do the timer retrigger only on the current CPU.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Soeren Sonnenburg <kernel@nn7.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On a SGI Altix TIOCP based PCI bus we need to include the ATE_PIO attribute
bit if we're mapping a 32bit MSI address.
Signed-off-by: Mike Habeck <habeck@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Just a one-byter for an ia64 thinko/typo - already fixed for i386 and x86_64.
Acked-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Revert all this. It can cause device-mapper to receive a different major from
earlier kernels and it turns out that the Amanda backup program (via GNU tar,
apparently) checks major numbers on files when performing incremental backups.
Which is a bit broken of Amanda (or tar), but this feature isn't important
enough to justify the churn.
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A device can be removed from an md array via e.g.
echo remove > /sys/block/md3/md/dev-sde/state
This will try to remove the 'dev-sde' subtree which will deadlock
since
commit e7b0d26a86
With this patch we run the kobject_del via schedule_work so as to
avoid the deadlock.
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
patch 4/4:
Limit ATAPI DMA to R/W commands only for TORiSAN DRD-N216 DVD-ROM drives
(http://bugzilla.kernel.org/show_bug.cgi?id=6710)
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
patch 3/4:
The TORiSAN drive locks up when max sector == 256.
Limit max sector to 128 for the TORiSAN DRD-N216 drives.
(http://bugzilla.kernel.org/show_bug.cgi?id=6710)
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
patch 1/4:
Reorder HSM_ST_FIRST, such that the task state transition is easier decoded with human eyes.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add unsigned to unused bit field in a.out.h to make sparse happy.
[ I took care of the sparc64 side as well -DaveM ]
Signed-off-by: Robert Reif <reif@earthlink.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://one.firstfloor.org/home/andi/git/linux-2.6:
[PATCH] x86: Don't probe for DDC on VBE1.2
[PATCH] x86-64: Increase NMI watchdog probing timeout
[PATCH] x86-64: Let oprofile reserve MSR on all CPUs
[PATCH] x86-64: Disable local APIC timer use on AMD systems with C1E
Fix the regression resulting from the recent change of suspend code
ordering that causes systems based on Intel x86 CPUs using the microcode
driver to hang during the resume.
The problem occurs since the microcode driver uses request_firmware() in
its CPU hotplug notifier, which is called after tasks has been frozen and
hangs. It can be fixed by telling the microcode driver to use the
microcode stored in memory during the resume instead of trying to load it
from disk.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Adrian Bunk <bunk@stusta.de>
Cc: Tigran Aivazian <tigran@aivazian.fsnet.co.uk>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Maxim <maximlevitsky@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently we have a confused udelay implementation.
* __const_udelay does not accept usecs but xloops in i386 and x86_64
* our implementation requires usecs as arg
* it gets a xloops count when called by asm/arch/delay.h
Bugs related to this (extremely long shutdown times) where reported by some
x86_64 users, especially using Device Mapper.
To hit this bug, a compile-time constant time parameter must be passed -
that's why UML seems to work most times. Fix this with a simple udelay
implementation.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Acked-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
AMD dual core laptops with C1E do not run the APIC timer correctly
when they go idle. Previously the code assumed this only happened
on C2 or deeper. But not all of these systems report support C2.
Use a AMD supplied snippet to detect C1E being enabled and then disable
local apic timer use.
This supercedes an earlier workaround using DMI detection of specific systems.
Thanks to Mark Langsdorf for the detection snippet.
Signed-off-by: Andi Kleen <ak@suse.de>
This patch:
- Switches mb/rmb/wmb back to being full-blown DMBs on ARM SMP systems,
since mb/rmb/wmb are required to order Normal memory accesses as well.
- Enables the use of DMB and ISB on XSC3 (which is an ARMv5TE ISA core
but conforms to the ARMv6 memory ordering model and supports the
various ARMv6 barriers.)
- Makes DMA coherent platforms (only ixp23xx at the moment) map
mb/rmb/wmb to dmb(), as on DMA coherent platforms, DMA consistent
mappings are done as Normal mappings, which are weakly ordered.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Acked-by: David Howells <dhowells@redhat.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There was a typo in commit 7632fc8f80,
preventing it from working - 32bit binaries crashed hopelessly before
the below fix and work perfectly now.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix compilation fail for ixp4xx platforms for the case when CONFIG_IXP4XX_INDIRECT_PCI is set. That is due to the check_signature() is appeared in include/linux/io.h.
Signed-off-by: Vladimir Barinov <vbarinov@ru.mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
local_irq_restore -> raw_local_irq_restore -> irq_restore_epilog ->
smtc_ipi_replay -> smtc_ipi_dq -> spin_unlock_irqrestore ->
_spin_unlock_irqrestore -> local_irq_restore
The recursion does abort when there is no more IPI queued for a CPU, so
this isn't usually fatal which is why we got away with this for so long
until this was discovered by code inspection.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The definition of struct ucc_slow puts the guemr register immediately after the
utpt register, when it should be at offset 0x90. This patch adds the missing
0x52-byte padding.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The input_device pointer is not refcounted, which means the device may
disappear while packets are queued, causing a crash when ifb passes packets
with a stale skb->dev pointer to netif_rx().
Fix by storing the interface index instead and do a lookup where neccessary.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Acked-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
_PAGE_PROTNONE conflicts with the lowest bit of pgoff. This causes all sorts
of weirdness when nonlinear mappings are used.
Took me a good half day to track this down.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Acked-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Josh Boyer
Paul Mackerras
Christian Krafft
Arnd Bergmann
Benjamin Herrenschmidt
Stephen Rothwell
Olof Johansson
Sylvain Munaut
Linus Torvalds
Suleiman Souhlal
Zachary Amsden
Ingo Molnar
Mike Habeck
Maciej Zenczykowski
Andrew Morton
NeilBrown
Albert Lee
Robert Reif
Rafael J. Wysocki
Kay Sievers
Paolo 'Blaisorblade' Giarrusso
Andi Kleen
Lennert Buytenhek
Russell King
Vladimir Barinov
Ralf Baechle
Timur Tabi
Patrick McHardy
Miklos Szeredi
Yinghai Lu