In function xadc_probe, xadc_write_adc_reg can return an error value
when write fails. The fix checks for the return value consistent with
other invocations of the latter function.
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Meson8b and Meson8m2 use the same logic to convert the ADC register
value to celsius, which is different from Meson8:
- Meson8 has different multiplier and divider values
- Meson8 uses a 4-bit TSC (temperature sensor coefficient) which fits
into the 4-bit field in the MESON_SAR_ADC_DELTA_10 register:
MESON_SAR_ADC_DELTA_10_TS_C_MASK. Meson8b and Meson8m2 have a 5-bit
TSC which requires writing the upper-most bit into the
MESON_HHI_DPLL_TOP_0[9] register from the HHI register area.
This adds support for the temperature sensor on the Meson8b and Meson8m2
SoCs by implementing the logic to write the upper-most TSC bit into the
HHI register area. The SoC-specific values (temperature_trimming_bits,
temperature_multiplier, temperature_divider) are added - these simply
integrate into the existing infrastructure (which was implemented for
Meson8) and thus require no further changes to the existing temperature
calculation logic.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Meson8b and Meson8m2 use a 5-bit wide TSC (temperature sensor
coefficient). The SAR ADC registers however can only store (the lower)
4 bits. The fifth (upper-most) bit is stored inside the
MESON_HHI_DPLL_TOP_0[9] register from the HHI register area.
This adds a syscon property to the HHI register area so a driver can
fetch the HHI register map and store the fifth TSC bit in there.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Document support for AD7606 Analog to Digital Converter.
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Move ad7606 ADC driver out of staging and into the mainline.
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
* Placed includes in alphabetical order
* Added brackets around num and mask through out for AD760X_CHANNEL
* Used single line comments where needed
* Removed extra lines and spaces
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch replaces the use of a polling ring buffer with a threaded
interrupt.
Enabling the buffer sets the CONVST signal to high. When the rising edge
of the CONVST is applied, BUSY signal goes logic high and transitions low
at the end of the entire conversion process. The falling edge of the BUSY
signal triggers the interrupt.
ad7606_trigger_handler() is used as bottom half of the poll function.
It reads data from the device and stores it in the internal buffer.
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch replaces the license text at the top of ad7606 driver files
and instead adds SPDX GPL-2.0 license identifier.
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
There is no point in having three menu entries that can be selected
individually. Instead, the SPI and parallel interfaces should select
AD7606.
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
If ad9523_write() fails, indio_dev may get incorrect data. The fix
inserts a check for the return value of ad9523_write(), and it fails,
returns an error.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Self cleaning is especially useful in cases where sensor undergoes
frequent power on/off cycles. In such scenarios it is recommended to
turn self cleaning at least once per week in order to maintain reliable
measurements.
Self cleaning is activated by writing 1 to a dedicated attribute.
Internal fan accelerates to its maximum speed and keeps spinning
for about 10 seconds blowing out accumulated dust.
Signed-off-by: Tomasz Duszynski <tduszyns@gmail.com>
Tested-by: Andreas Brauchli <andreas.brauchli@sensirion.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_shub.c: In function 'st_lsm6dsx_shub_read_reg':
drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_shub.c:108:41: warning:
variable 'hub_settings' set but not used [-Wunused-but-set-variable]
It never used since introduction in commit c91c1c844e ("iio: imu: st_lsm6dsx:
add i2c embedded controller support")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The driver does not have a struct of_device_id table, but supported
devices are registered via Device Trees. This patch adds and OF device
ID table.
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The 'adi' vendor prefix needs to be added to conversion-start, range,
first-data and oversampling-ratio properties.
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When looking for the available scale or oversampling ratio, it is better
to use the find_closest() macro. This simplifies the code and also does
not require an exact value to be entered from the user space.
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Switch to devm version of request_irq, iio_triggered_buffer_setup,
iio_device_register. To avoid potential ordering issues in probe,
devm_add_action_or_reset() is used for the regulator_disable(). This
simplifies the code and decreases the chance of bugs.
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch replaces the use of wait_event_interruptible() with
wait_for_completion_timeout() when reading the result of a single
conversion. In this way, if the interrupt never occurs, the program will
not remain blocked.
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add device tree support for Sensirion SGP30/SGPC3 gas sensors.
Signed-off-by: Andreas Brauchli <andreas.brauchli@sensirion.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Support Sensirion SGP30 and SGPC3 multi-pixel I2C gas sensors
Supported Features:
* Indoor Air Quality (IAQ) concentrations for
- tVOC (in_concentration_voc_input)
- CO2eq (in_concentration_co2_input) - SGP30 only
IAQ concentrations are periodically read out by a background thread
to allow the sensor to maintain its internal baseline.
* Gas concentration signals
- Ethanol (in_concentration_ethanol_raw)
- H2 (in_concentration_h2_raw) - SGP30 only
https://www.sensirion.com/file/datasheet_sgp30https://www.sensirion.com/file/datasheet_sgpc3
Signed-off-by: Andreas Brauchli <andreas.brauchli@sensirion.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add ethanol and H2 gas modifiers:
* IIO_MOD_ETHANOL
* IIO_MOD_H2
Signed-off-by: Andreas Brauchli <andreas.brauchli@sensirion.com>
Acked-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add device tree support for Sensirion SPS30 particulate
matter sensor.
Signed-off-by: Tomasz Duszynski <tduszyns@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support for Sensirion SPS30 particulate matter sensor.
Signed-off-by: Tomasz Duszynski <tduszyns@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Measuring particulate matter in ug / m3 (micro-grams per cubic meter)
is de facto standard. Existing air quality sensors usually follow
this convention and are capable of returning measurements using
this unit.
IIO currently does not offer suitable channel type for this
type of measurements hence this patch adds this.
In addition, extra modifiers are introduced used for distinguishing
between fine pm1, pm2p5 and coarse pm4, pm10 particle measurements, i.e
IIO_MOD_PM1, IIO_MOD_PM25 and IIO_MOD_PM4, IIO_MOD_PM10.
pmX consists of particles with aerodynamic diameter less or equal to
X micrometers.
Signed-off-by: Tomasz Duszynski <tduszyns@gmail.com>
Acked-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Initialization is unnecessary when the variable is written before it is
read. There were some occasions in which the driver would initialize `ret'
during declaration without need.
Signed-off-by: Hardik Singh Rathore <hardiksingh.k@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ad7280_attr_init function has been split into more specific
functions to increase the code readability.
Signed-off-by: Slawomir Stepien <sst@poczta.fm>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ad7280_channel_init function has been split into more specific
functions to increase the code readability.
The setting of channel's scan_type.shift to 0, has been removed, since
it is the default value.
Signed-off-by: Slawomir Stepien <sst@poczta.fm>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add a devicetree documentation for the ad5933 and ad5934 impedance
converter, network analyzer.
Signed-off-by: Marcelo Schmitt <marcelo.schmitt1@gmail.com>
Signed-off-by: Gabriel Capella <gabriel@capella.pro>
Co-Developed-by: Gabriel Capella <gabriel@capella.pro>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add the option to specify the external clock (MCLK) using the clock
framework.
Also remove the old platform data structure.
Signed-off-by: Marcelo Schmitt <marcelo.schmitt1@gmail.com>
Signed-off-by: Gabriel Capella <gabriel@capella.pro>
Co-developed-by: Gabriel Capella <gabriel@capella.pro>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Set a single voltage regulator for all voltage references.
Remove voltage reference value from default platafrom data struct.
Signed-off-by: Marcelo Schmitt <marcelo.schmitt1@gmail.com>
Signed-off-by: Gabriel Capella <gabriel@capella.pro>
Co-developed-by: Gabriel Capella <gabriel@capella.pro>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
ADT7316 driver no more uses platform data and hence use device tree
data instead of platform data for assigning irq_type field and
implement this in adt7316_irq_setup function.
Switch case figures out the type of irq and if it's the default case
then assign the default value to the irq_type i.e.
irq_type = IRQF_TRIGGER_LOW
Move devm_request_threaded_irq() and assignment of chip->config1
into the adt7316_setup_irq() to unclutter the code in probe function.
Signed-off-by: Shreeya Patel <shreeya.patel23498@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Initialization is unnecessary when the variable is written before it is
read. There were some occasions in which the driver would initialize `ret'
during declaration without need.
Purely a cosmetic change with no functional impact.
Signed-off-by: Hardik Singh Rathore <hardiksingh.k@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Based on the output of adt7316_show_all_DAC_update_modes() and
adt7316_show_DAC_update_mode(), adt7316_store_DAC_update_mode() should
expect the user to enter an integer input from 0 to 3. The user input is
currently expected to account for the actual bit positions in the register.
For example, choosing option 3 would require a write of 0x30 (actually 48
since it expects base 10). To address this inconsistency, create a shift
macro to be used in the valid input check as well as the calculation for
the register write.
Signed-off-by: Jeremy Fertic <jeremyfertic@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The option to allow the external vref to bypass the reference buffer is
only available for adt7316/7/8. Remove the attributes for adt751x as
well as the chip->id checks from the show and store functions.
Signed-off-by: Jeremy Fertic <jeremyfertic@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
With adt7516/7/9, internal vref is available for dacs a and b, dacs c and
d, or all dacs. The driver doesn't currently support internal vref for all
dacs. Change the else if to an if so both bits are checked rather than
just one or the other.
Signed-off-by: Jeremy Fertic <jeremyfertic@gmail.com>
Fixes: 35f6b6b86e ("staging: iio: new ADT7316/7/8 and ADT7516/7/9 driver")
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The dac internal vref settings are part of the ldac config register rather
than the dac config register. Change the variable being used so the read
returns the correct result.
Whilst a fix, it is for a driver in heavy churn so do not backport
to stable without taking considerable care and testing.
Signed-off-by: Jeremy Fertic <jeremyfertic@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
ADT7316_DA_EN_VIA_DAC_LDCA is set when the dac and ldac registers are being
used to update the dacs instead of the ldac pin. ADT7516_SEL_AIN3 is an adc
input that shares the ldac pin. Only set these bits if an ldac pin is not
being used.
This could be backported to stable, but note there are various
other bugs that probably make that a waste of time.
Signed-off-by: Jeremy Fertic <jeremyfertic@gmail.com>
Fixes: 35f6b6b86e ("staging: iio: new ADT7316/7/8 and ADT7516/7/9 driver")
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Change two register addresses and one bit definition to match the
datasheet.
Note that there are many issues in this driver so I would
not suggest backporting these fixes to stable trees.
Signed-off-by: Jeremy Fertic <jeremyfertic@gmail.com>
Fixes: 35f6b6b86e ("staging: iio: new ADT7316/7/8 and ADT7516/7/9 driver")
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Staging graduation
* ad2s90
- Driver for this resolver to digital chip.
New drivers and device support.
* ad5686
- Add support for ad5310r DAC and associated fix in value read back.
* exynos-adc
- Support for S5PV210 which is slightly different from other parts.
* mcp41010
- Driver supporting MCP41010, MCP41050, MCP41100, MCP42010, MCP42050 and
MCP42100 microchip potentiometers.
New ACPI ids.
* ak8975
- AKM9911 ACPI HID.
* kxcjk-1013
- KXJ2109 ACPI HID.
- KIOX010A ACPI HID.
New features
* ad5933
- Explicit DT binding.
* ad2s90
- Explicit DT binding including dropping spi setup that is done via dt
in favour of verifying the settings form DT.
* adt7316
- Explicit DT binding and support for gpio, irq_flags etc.
* stm32-adc
- Runtime power management.
Minor fixes and cleanups
* core
- Protect against missing info structure.
* ad2s90
- SPDX
- Add documentation fo the mutex.
* ad7280a
- Check allocation failure.
- Fix an accidental replacement of an error return.
* adt7316
- Switch some variables to be local and rename for consistency with other
drivers.
- Revert a false handling of 0 as an error introduced earlier this cycle.
* bmi160
- Use devm functions throughout probe() to avoid need for remove().
* hid-sensor-hub
- White space cleanup.
* hts221
- MAINTAINERS entry.
* lis302
- Use generic name in the DT binding doc.
* Messon-saradc
- Check for allocation error.
- Fix some presented clock names that break clk debugfs.
* qcom-spmi-adc
- A fix for initialization of the prescale property. Came late in the
cycle, so merge window is probably the best route for this.
* st_lsm6dsx
- Allow for variable read length to support wider range of slave devices.
-----BEGIN PGP SIGNATURE-----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=+vyl
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.21b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Second set of IIO new device support, features and cleanups for the 4.21 cycle.
Staging graduation
* ad2s90
- Driver for this resolver to digital chip.
New drivers and device support.
* ad5686
- Add support for ad5310r DAC and associated fix in value read back.
* exynos-adc
- Support for S5PV210 which is slightly different from other parts.
* mcp41010
- Driver supporting MCP41010, MCP41050, MCP41100, MCP42010, MCP42050 and
MCP42100 microchip potentiometers.
New ACPI ids.
* ak8975
- AKM9911 ACPI HID.
* kxcjk-1013
- KXJ2109 ACPI HID.
- KIOX010A ACPI HID.
New features
* ad5933
- Explicit DT binding.
* ad2s90
- Explicit DT binding including dropping spi setup that is done via dt
in favour of verifying the settings form DT.
* adt7316
- Explicit DT binding and support for gpio, irq_flags etc.
* stm32-adc
- Runtime power management.
Minor fixes and cleanups
* core
- Protect against missing info structure.
* ad2s90
- SPDX
- Add documentation fo the mutex.
* ad7280a
- Check allocation failure.
- Fix an accidental replacement of an error return.
* adt7316
- Switch some variables to be local and rename for consistency with other
drivers.
- Revert a false handling of 0 as an error introduced earlier this cycle.
* bmi160
- Use devm functions throughout probe() to avoid need for remove().
* hid-sensor-hub
- White space cleanup.
* hts221
- MAINTAINERS entry.
* lis302
- Use generic name in the DT binding doc.
* Messon-saradc
- Check for allocation error.
- Fix some presented clock names that break clk debugfs.
* qcom-spmi-adc
- A fix for initialization of the prescale property. Came late in the
cycle, so merge window is probably the best route for this.
* st_lsm6dsx
- Allow for variable read length to support wider range of slave devices.
* tag 'iio-for-4.21b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (37 commits)
iio: adc: qcom-spmi-adc5: Initialize prescale properly
dt-bindings: iio: adc: exynos-adc: Add S5PV210 variant
iio: adc: Allow selection of Exynos ADC on S5PV210
iio: adc: exynos-adc: Add S5PV210 variant
iio: bmi160: use all devm functions in probe
iio: dac: ad5686: fix bit shift read register
iio:dac:ad5686: Add AD5310R support
Revert "Staging: iio: adt7316: Add an extra check for 'ret' equals to 0"
dt-bindings: iio: accel: use a generic node name for lis302
iio: core: check 'info' value before registering the device
staging: iio: adc: ad7280a: fix overwrite of the returned value
staging: iio: adc: ad7280a: check for devm_kasprint() failure
iio: humidity: hts221: add entry in MAINTAINERS file
iio: magnetometer: ak8975: Add the "AKM9911" ACPI HID
staging:iio:ad2s90: Move out of staging
staging:iio:ad2s90: Add comment to device state mutex
staging:iio:ad2s90: Replace license text w/ SPDX identifier
dt-bindings:iio:resolver: Add docs for ad2s90
staging:iio:ad2s90: Add max frequency check at probe
staging:iio:ad2s90: Remove spi setup that should be done via dt
...
adc5_get_dt_data uses a local, prop, feeds it to adc5_get_dt_channel_data,
and then puts the result into adc->chan_props. The problem is
adc5_get_dt_channel_data may not initialize that structure fully, so a
garbage value is used for prescale if the optional "qcom,pre-scaling" is
not defined in DT. adc5_read_raw then uses this as an array index,
generating a crash that looks like this:
[ 6.683186] Unable to handle kernel paging request at virtual address ffffff90e78c7964
Call trace:
qcom_vadc_scale_code_voltage_factor+0x74/0x104
qcom_vadc_scale_hw_calib_die_temp+0x20/0x60
qcom_adc5_hw_scale+0x78/0xa4
adc5_read_raw+0x3d0/0x65c
iio_channel_read+0x240/0x30c
iio_read_channel_processed+0x10c/0x150
qpnp_tm_get_temp+0xc0/0x40c
of_thermal_get_temp+0x7c/0x98
thermal_zone_get_temp+0xac/0xd8
thermal_zone_device_update+0xc0/0x38c
qpnp_tm_probe+0x624/0x81c
platform_drv_probe+0xe4/0x11c
really_probe+0x188/0x3fc
driver_probe_device+0xb8/0x188
__device_attach_driver+0x114/0x180
bus_for_each_drv+0xd8/0x118
__device_attach+0x180/0x27c
device_initial_probe+0x20/0x2c
bus_probe_device+0x78/0x124
deferred_probe_work_func+0xfc/0x138
process_one_work+0x3d8/0x8b0
process_scheduled_works+0x48/0x6c
worker_thread+0x488/0x7cc
kthread+0x24c/0x264
ret_from_fork+0x10/0x18
Unfortunately, when I went to add the initializer for this and tried to
boot it, my machine shut down immediately, complaining that it was
hotter than the sun. It appears that adc5_chans_pmic and adc5_chans_rev2
were initializing prescale_index as if it were directly a divisor,
rather than the index into adc5_prescale_ratios that it is.
Fix the uninitialized value, and change the static initialization to use
indices into adc5_prescale_ratios.
Signed-off-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add information about new compatible for S5PV210
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Make it possible to use Exynos ADC driver on S5PV210 based devices.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
S5PV210's ADC variant is almost the same as v1 except that it has 10
channels and doesn't require the pmu register
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Commit 2a54e3259e ("staging: mt7621-mmc: Remove #if 0 blocks in sd.c")
does not completely remove an #if 0 block in sd.c. This causes the function
msdc_select_clksrc() which was eariler not compiled, to be compiled.
That causes an error - MSDC_CLKSRC_REG is not defined.
This patch completely removes the #if 0 block
Reported-by: NeilBrown <neil@brown.name>
Fixes: 2a54e3259e ("staging: mt7621-mmc: Remove #if 0 blocks in sd.c")
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Reviewed-by: NeilBrown <neil@brown.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As per default the GPU memory config of the Raspberry Pi isn't sufficient
for the camera usage. Even worse the bcm2835 camera driver doesn't provide a
helpful error message in this case. So let's add a hint to point the user
to the likely cause.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently there is only a catch-all info message which print the
relevant error code without any context. So add more specific error
messages in order to narrow down possible issues.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Just like the bcm2835-video make this a platform driver which is probed
by vchiq. In order to change the number of channels use a module
parameter instead, but use the maximum as default.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is not much value behind this boilerplate, so use
module_platform_driver() instead.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enable the compilation test for bcm2835-audio to gain more build coverage.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Following Eric's commit 37b7b3087a ("staging/vc04_services: Register a
platform device for the camera driver.") this register the audio driver as
a platform device, too.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Aditya Pakki
Martin Blumenstingl
Stefan Popa
Kangjie Lu
Tomasz Duszynski
YueHaibing
Andreas Brauchli
Hardik Singh Rathore
Slawomir Stepien
Marcelo Schmitt
Shreeya Patel
Jeremy Fertic
Greg Kroah-Hartman
Evan Green
Jonathan Bakker
Nishad Kamdar
Stefan Wahren