This reverts commit e8b373326d. Many xHCI
host controllers can only handle 32-bit addresses, and writing 64-bits
at a time causes them to fail. Reading 64-bits at a time may also cause
them to return 0xffffffff, so revert this commit as well.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This reverts commit 7dd09a1af2.
Many xHCI host controllers can only handle 32-bit addresses, and writing
64-bits at a time causes them to fail. Rafał reports that USB devices
simply do not enumerate, and reverting this patch helps. Branimir
reports that his host controller doesn't respond to an Enable Slot
command and dies:
[ 75.576160] xhci_hcd 0000:03:00.0: Timeout while waiting for a slot
[ 88.991634] xhci_hcd 0000:03:00.0: Stopped the command ring failed, maybe the host is dead
[ 88.991748] xhci_hcd 0000:03:00.0: Abort command ring failed
[ 88.991845] xhci_hcd 0000:03:00.0: HC died; cleaning up
[ 93.985489] xhci_hcd 0000:03:00.0: Timeout while waiting for a slot
[ 93.985494] xhci_hcd 0000:03:00.0: Abort the command ring, but the xHCI is dead.
[ 98.982586] xhci_hcd 0000:03:00.0: Timeout while waiting for a slot
[ 98.982591] xhci_hcd 0000:03:00.0: Abort the command ring, but the xHCI is dead.
[ 103.979696] xhci_hcd 0000:03:00.0: Timeout while waiting for a slot
[ 103.979702] xhci_hcd 0000:03:00.0: Abort the command ring, but the xHCI is dead
Signed-off-by: Sarah Sharp <sarah.a.sharp@intel.com>
Reported-by: Rafał Miłecki <zajec5@gmail.com>
Reported-by: Branimir Maksimovic <branimir.maksimovic@gmail.com>
Cc: Xenia Ragiadakou <burzalodowa@gmail.com>
Function xhci_write_64() is used to write 64bit xHC registers residing in MMIO.
On 32bit systems, xHC registers need to be written with 32bit accesses by
writing first the lower 32bits and then the higher 32bits. The header file
asm-generic/io-64-nonatomic-lo-hi.h ensures that on 32bit systems writeq() will
will write 64bit registers in 32bit chunks with low-high order.
Replace all calls to xhci_write_64() with calls to writeq().
This is done to reduce code duplication since 64bit low-high write logic
is already implemented and to take advantage of inherent "atomic" 64bit
write operations on 64bit systems.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Function xhci_read_64() is used to read 64bit xHC registers residing in MMIO.
On 32bit systems, xHC registers need to be read with 32bit accesses by
reading first the lower 32bits and then the higher 32bits.
Replace all calls to xhci_read_64() with calls to readq() and include
asm-generic/io-64-nonatomic-lo-hi.h header file, so that if the system
is not 64bit, readq() will read registers in 32bit chunks with low-high order.
This is done to reduce code duplication since 64bit low-high read logic
is already implemented and to take advantage of inherent "atomic" 64bit
read operations on 64bit systems.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Function xhci_writel() is used to write a 32bit value in xHC registers residing
in MMIO address space. It takes as first argument a pointer to the xhci_hcd
although it does not use it. xhci_writel() internally simply calls writel().
This creates an illusion that xhci_writel() is an xhci specific function that
has to be called in a context where a pointer to xhci_hcd is available.
Remove xhci_writel() wrapper function and replace its calls with calls to
writel() to make the code more straight-forward.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Function xhci_readl() is used to read 32bit xHC registers residing in MMIO
address space. It takes as first argument a pointer to the xhci_hcd although
it does not use it. xhci_readl() internally simply calls readl(). This creates
an illusion that xhci_readl() is an xhci specific function that has to be
called in a context where a pointer to xhci_hcd is available.
Remove the unnecessary xhci_readl() wrapper function and replace its calls to
with calls to readl() to make the code more straightforward.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This patch removes the to_pci_dev() conversion performed to generic struct
device since it is not actually useful (the pointer to the generic device
can be used directly rather through a conversion to pci_dev) and it is pci
bus specific.
This isn't stable material because this code will produce harmless
behavior on non-PCI xHCI hosts. The pci_device pointer is never
dereferenced, only used to re-calculate the underlying device pointer.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This patch removes the unneccessary check 'if (stream_info)' because
there is already a check few lines above which ensures that stream_info
is not NULL.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This patch converts TRB_CYCLE to le32 to update correctly the Cycle Bit in
'control' field of the link TRB.
This bug was found using sparse.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
How it's supposed to work:
--------------------------
USB 2.0 Link PM is a lower power state that some newer USB 2.0 devices
support. USB 3.0 devices certified by the USB-IF are required to
support it if they are plugged into a USB 2.0 only port, or a USB 2.0
cable is used. USB 2.0 Link PM requires both a USB device and a host
controller that supports USB 2.0 hardware-enabled LPM.
USB 2.0 Link PM is designed to be enabled once by software, and the host
hardware handles transitions to the L1 state automatically. The premise
of USB 2.0 Link PM is to be able to put the device into a lower power
link state when the bus is idle or the device NAKs USB IN transfers for
a specified amount of time.
...but hardware is broken:
--------------------------
It turns out many USB 3.0 devices claim to support USB 2.0 Link PM (by
setting the LPM bit in their USB 2.0 BOS descriptor), but they don't
actually implement it correctly. This manifests as the USB device
refusing to respond to transfers when it is plugged into a USB 2.0 only
port under the Haswell-ULT/Lynx Point LP xHCI host.
These devices pass the xHCI driver's simple test to enable USB 2.0 Link
PM, wait for the port to enter L1, and then bring it back into L0. They
only start to break when L1 entry is interleaved with transfers.
Some devices then fail to respond to the next control transfer (usually
a Set Configuration). This results in devices never enumerating.
Other mass storage devices (such as a later model Western Digital My
Passport USB 3.0 hard drive) respond fine to going into L1 between
control transfers. They ACK the entry, come out of L1 when the host
needs to send a control transfer, and respond properly to those control
transfers. However, when the first READ10 SCSI command is sent, the
device NAKs the data phase while it's reading from the spinning disk.
Eventually, the host requests to put the link into L1, and the device
ACKs that request. Then it never responds to the data phase of the
READ10 command. This results in not being able to read from the drive.
Some mass storage devices (like the Corsair Survivor USB 3.0 flash
drive) are well behaved. They ACK the entry into L1 during control
transfers, and when SCSI commands start coming in, they NAK the requests
to go into L1, because they need to be at full power.
Not all USB 3.0 devices advertise USB 2.0 link PM support. My Point
Grey USB 3.0 webcam advertises itself as a USB 2.1 device, but doesn't
have a USB 2.0 BOS descriptor, so we don't enable USB 2.0 Link PM. I
suspect that means the device isn't certified.
What do we do about it?
-----------------------
There's really no good way for the kernel to test these devices.
Therefore, the kernel needs to disable USB 2.0 Link PM by default, and
distros will have to enable it by writing 1 to the sysfs file
/sys/bus/usb/devices/../power/usb2_hardware_lpm. Rip out the xHCI Link
PM test, since it's not sufficient to detect these buggy devices, and
don't automatically enable LPM after the device is addressed.
This patch should be backported to kernels as old as 3.11, that
contain the commit a558ccdcc7 "usb: xhci:
add USB2 Link power management BESL support". Without this fix, some
USB 3.0 devices will not enumerate or work properly under USB 2.0 ports
on Haswell-ULT systems.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
When a device signals remote wakeup on a roothub, and the suspend change
bit is set, the host controller driver must not give control back to the
USB core until the port goes back into the active state.
EHCI accomplishes this by waiting in the get port status function until
the PORT_RESUME bit is cleared:
/* stop resume signaling */
temp &= ~(PORT_RWC_BITS | PORT_SUSPEND | PORT_RESUME);
ehci_writel(ehci, temp, status_reg);
clear_bit(wIndex, &ehci->resuming_ports);
retval = ehci_handshake(ehci, status_reg,
PORT_RESUME, 0, 2000 /* 2msec */);
Similarly, the xHCI host should wait until the port goes into U0, before
passing control up to the USB core. When the port transitions from the
RExit state to U0, the xHCI driver will get a port status change event.
We need to wait for that event before passing control up to the USB
core.
After the port transitions to the active state, the USB core should time
a recovery interval before it talks to the device. The length of that
recovery interval is TRSMRCY, 10 ms, mentioned in the USB 2.0 spec,
section 7.1.7.7. The previous xHCI code (which did not wait for the
port to go into U0) would cause the USB core to violate that recovery
interval.
This bug caused numerous USB device disconnects on remote wakeup under
ChromeOS and a Lynx Point LP xHCI host that takes up to 20 ms to move
from RExit to U0. ChromeOS is very aggressive about power savings, and
sets the autosuspend_delay to 100 ms, and disables USB persist.
I attempted to replicate this bug with Ubuntu 12.04, but could not. I
used Ubuntu 12.04 on the same platform, with the same BIOS that the bug
was triggered on ChromeOS with. I also changed the USB sysfs settings
as described above, but still could not reproduce the bug under Ubuntu.
It may be that ChromeOS userspace triggers this bug through additional
settings.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This patch defines a new trace event, which is called xhci_dbg_ring_expansion
and belongs to the event class xhci_log_msg, and adds tracepoints that trace
the debug messages associated with the expansion of endpoint ring when there
is not enough space allocated to hold all pending TRBs.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This patch defines a new trace event, which is called xhci_dbg_init
and belongs to the event class xhci_log_msg, and adds tracepoints that
trace the debug statements in the functions used to start and stop the
xhci-hcd driver.
Also, it removes an unnecessary cast of variable val to unsigned int
in xhci_mem_init(), since val is already declared as unsigned int.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This patch defines a new trace event, which is called xhci_dbg_context_change
and belongs in the event class xhci_log_msg, and adds tracepoints for tracing
the debug messages related to context updates performed with Configure Endpoint
and Evaluate Context commands.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
CONFIG_USB_XHCI_HCD_DEBUGGING option is used to enable
verbose debugging output for the xHCI host controller
driver.
In the current version of the xhci-hcd driver, this
option must be turned on, in order for the debugging
log messages to be displayed, and users may need to
recompile the linux kernel to obtain debugging
information that will help them track down problems.
This patch removes the above debug option to enable
debugging log messages at all times.
The aim of this is to rely on the debugfs and the
dynamic debugging feature for fine-grained management
of debugging messages and to not force users to set
the debug config option and compile the linux kernel
in order to have access in that information.
This patch, also, removes the XHCI_DEBUG symbol and the
functions dma_to_stream_ring(), xhci_test_radix_tree()
and xhci_event_ring_work() that are not useful anymore.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
A randconfig build hit the following build errors because xhci.c and
xhci-mem.c use dma mapping functions but don't include
<linux/dma-mapping.h>. Add the missing includes to fix the build errors.
drivers/usb/host/xhci.c In function 'xhci_gen_setup':
drivers/usb/host/xhci.c +4872 : error: implicit declaration of function 'dma_set_mask'
drivers/usb/host/xhci.c +4872 : error: implicit declaration of function 'DMA_BIT_MASK'
drivers/usb/host/xhci-mem.c In function 'xhci_free_stream_ctx':
drivers/usb/host/xhci-mem.c +435 : error: implicit declaration of function 'dma_free_coherent'
drivers/usb/host/xhci-mem.c In function 'xhci_alloc_stream_ctx':
drivers/usb/host/xhci-mem.c +463 : error: implicit declaration of function 'dma_alloc_coherent'
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Fail and free the container context in case dma_pool_alloc() can't allocate
the raw context data part of it
This patch should be backported to kernels as old as 2.6.31, that
contain the commit d115b04818 "USB: xhci:
Support for 64-byte contexts".
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: John Youn <johnyoun@synopsys.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the endpoint type is unknown, set it to 0 and fail gracefully
instead of causing a kernel panic.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
We may have more speed types in the future, so fail gracefully, rather
than causing the kernel to panic.
BUG() was called if the device speed was unknown when setting max packet
size. Set the max packet size at the same time as the slot speed and
get rid of one switch statement with BUG() option completely.
[Note: Sarah merged a patch that she wrote that touched the
xhci_setup_addressable_virt_dev function with this patch from Mathias
for clarity.]
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Fail gracefully, instead of causing the kernel to panic, if the input
control context doesn't have the right type (XHCI_CTX_TYPE_INPUT). Push
finding the pointer to the input control context up into functions that
can fail.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: John Youn <johnyoun@synopsys.com>
It's horrible coding style to panic the kernel when someone passes you
an argument value you didn't expect. In the future, we may want to add
additional context types, so it's better to gracefully handle additional
context types instead of panicking.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: John Youn <johnyoun@synopsys.com>
Hardware link powermanagement in usb2 is a per-port capability.
Previously support for hw lpm was enabled for all ports if any usb2 port supported it.
Now instead cache the capability values and check them for each port individually
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
If for whatever reason we fall into fail path in xhci_mem_init()
before bw table gets initialized we may access the uninitialized lists
in xhci_mem_cleanup().
Check for bw table before traversing lists in cleanup routine.
This patch should be backported to kernels as old as 3.2, that contain
the commit 839c817ce6 "xhci: Store
information about roothubs and TTs."
Reported-by: Sergey Dyasly <dserrg@gmail.com>
Tested-by: Sergey Dyasly <dserrg@gmail.com>
Signed-off-by: Vladimir Murzin <murzin.v@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
It is possible that we fail on xhci_mem_init, just before doing
the INIT_LIST_HEAD, and calling xhci_mem_cleanup.
Problem is that, the list_for_each_entry_safe macro, assumes
list heads are initialized (not NULL), and dereferences their 'next'
pointer, causing a kernel panic if this is not yet initialized.
Let's protect from that by moving inits to the beginning.
This patch should be backported to kernels as old as 3.2, that
contain the commit 9574323c39 "xHCI: test
USB2 software LPM".
Signed-off-by: Sergio Aguirre <sergio.a.aguirre.rodriguez@intel.com>
Acked-by: David Cohen <david.a.cohen@intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
This patch shortens the logic in xhci_endpoint_init() by moving common
calculations involving max_packet and max_burst outside the switch
statement, rather than repeating the same code in multiple
case-specific statements. It also replaces two usages of max_packet
which were clearly intended to be max_burst all along.
More importantly, it compensates for a common bug in high-speed bulk
endpoint descriptors. In many devices there is a bulk endpoint having
a wMaxPacketSize value smaller than 512, which is forbidden by the USB
spec. Some xHCI controllers can't handle this and refuse to accept
the endpoint. This patch changes the max_packet value to 512, which
allows the controller to use the endpoint properly.
In practice the bogus maxpacket size doesn't matter, because none of
the transfers sent via these endpoints are longer than the maxpacket
value anyway.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: "Aurélien Leblond" <blablack@gmail.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rename SEGMENT_SIZE and SEGMENT_SHIFT as the former is used in a.out.h.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Sarah Sharp <sarah.a.sharp@linux.intel.com>
cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cc: linux-usb@vger.kernel.org
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
xhci driver divides the root hub into two logical hubs which work
respectively for usb 2.0 and usb 3.0 devices. They are independent
devices in the usb core. But in the ACPI table, it's one device node
and all usb2.0 and usb3.0 ports are under it. Binding usb port with
its acpi node needs the raw port number which is reflected in the xhci
extended capabilities table. This patch is to add find_raw_port_number
callback to struct hc_driver(), fill it with xhci_find_raw_port_number()
which will return raw port number and add a wrap usb_hcd_find_raw_port_number().
Otherwise, refactor xhci_find_real_port_number(). Using
xhci_find_raw_port_number() to get real index in the HW port status
registers instead of scanning through the xHCI roothub port array.
This can help to speed up.
All addresses in xhci->usb2_ports and xhci->usb3_ports array are
kown good ports and don't include following bad ports in the extended
capabilities talbe.
(1) root port that doesn't have an entry
(2) root port with unknown speed
(3) root port that is listed twice and with different speeds.
So xhci_find_raw_port_number() will only return port num of good ones
and never touch bad ports above.
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
A high speed control or bulk endpoint may have bInterval set to zero,
which means it does not NAK. If bInterval is non-zero, it means the
endpoint NAKs at a rate of 2^(bInterval - 1).
The xHCI code to compute the NAK interval does not handle the special
case of zero properly. The current code unconditionally subtracts one
from bInterval and uses it as an exponent. This causes a very large
bInterval to be used, and warning messages like these will be printed:
usb 1-1: ep 0x1 - rounding interval to 32768 microframes, ep desc says 0 microframes
This may cause the xHCI host hardware to reject the Configure Endpoint
command, which means the HS device will be unusable under xHCI ports.
This patch should be backported to kernels as old as 2.6.31, that contain
commit dfa49c4ad1 "USB: xhci - fix math in
xhci_get_endpoint_interval()".
Reported-by: Vincent Pelletier <plr.vincent@gmail.com>
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
xhci_alloc_segments_for_ring() builds a list of xhci_segments and links
the tail to head at the end (forming a ring). When it bails out for OOM
reasons half-way through, it tries to destroy its half-built list with
xhci_free_segments_for_ring(), even though it is not a ring yet. This
causes a null-pointer dereference upon hitting the last element.
Furthermore, one of its callers (xhci_ring_alloc()) mistakenly believes
the output parameters to be valid upon this kind of OOM failure, and
calls xhci_ring_free() on them. Since the (incomplete) list/ring should
already be destroyed in that case, this would lead to a use after free.
This patch fixes those issues by having xhci_alloc_segments_for_ring()
destroy its half-built, non-circular list manually and destroying the
invalid struct xhci_ring in xhci_ring_alloc() with a plain kfree().
This patch should be backported to kernels as old as 2.6.31, that
contains the commit 0ebbab3742 "USB: xhci:
Ring allocation and initialization."
A separate patch will need to be developed for kernels older than 3.4,
since the ring allocation code was refactored in that kernel.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
Software have to abort command ring and cancel command
when a command is failed or hang. Otherwise, the command
ring will hang up and can't handle the others. An example
of a command that may hang is the Address Device Command,
because waiting for a SET_ADDRESS request to be acknowledged
by a USB device is outside of the xHC's ability to control.
To cancel a command, software will initialize a command
descriptor for the cancel command, and add it into a
cancel_cmd_list of xhci.
Sarah: Fixed missing newline on "Have the command ring been stopped?"
debugging statement.
This patch should be backported to kernels as old as 3.0, that contain
the commit 7ed603ecf8 "xhci: Add an
assertion to check for virt_dev=0 bug." That commit papers over a NULL
pointer dereference, and this patch fixes the underlying issue that
caused the NULL pointer dereference.
Signed-off-by: Elric Fu <elricfu1@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: Miroslav Sabljic <miroslav.sabljic@avl.com>
Cc: stable@vger.kernel.org
This patch fixes a few issues introduced in the recent fix
[f8a9e72d: USB: fix resource leak in xhci power loss path]
- The endpoints listed in bw table are just links and each entry is an
array member of dev->eps[]. But the commit above adds a kfree() call
to these instances, and thus it results in memory corruption.
- It clears only the first entry of rh_bw[], but there can be multiple
ports.
- It'd be safer to clear the list_head of ep as well, not only
removing from the list, as it's checked in
xhci_discover_or_reset_device().
This patch should be backported to kernels as old as 3.2, that contain
the commit 839c817ce6 "xhci: Store
information about roothubs and TTs."
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reviewed-by: Oliver Neukum <oneukum@suse.de>
Cc: <stable@vger.kernel.org>
xhci_free_tt_info() may access the invalid memory when it removes the
last entry but the list is not empty. Then tt_next reaches to the
list head but it still tries to check the tt_info of that entry.
This patch fixes the bug and cleans up the messy code by rewriting
with a simple list_for_each_entry_safe().
This patch should be backported to kernels as old as 3.2, that contain
the commit 839c817ce6 "xhci: Store
information about roothubs and TTs."
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reviewed-by: Oliver Neukum <oneukum@suse.de>
Cc: <stable@vger.kernel.org>
We want to do everything we can to ensure that USB 3.0 Link Power
Management (LPM) can be disabled when it is enabled. If LPM can't be
disabled, we can't suspend USB 3.0 devices, or reset them. To make sure
we can submit the command to disable LPM, allocate a command in the
xhci_hcd structure, and reserve one TRB on the command ring.
We only need one command per xHCI driver instance, because LPM is only
disabled or enabled while the USB core is holding the bandwidth_mutex
that is shared between the xHCI USB 2.0 and USB 3.0 roothubs. The
bandwidth_mutex will be held until the command completes, or times out.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
When the xHCI driver needs to clean up memory (perhaps due to a failed
register restore on resume from S3 or resume from S4), it needs to reset
the number of reserved TRBs on the command ring to zero. Otherwise,
several resume cycles (about 30) with a UAS device attached will
continually increment the number of reserved TRBs, until all command
submissions fail because there isn't enough room on the command ring.
This patch should be backported to kernels as old as 2.6.32,
that contain the commit 913a8a344f
"USB: xhci: Change how xHCI commands are handled."
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
Some more data structures must be freed and counters
reset if an XHCI controller has lost power. The failure
to do so renders some chips inoperative after a certain number
of S4 cycles.
This patch should be backported to kernels as old as 3.2,
that contain the commits c29eea6219
"xhci: Implement HS/FS/LS bandwidth checking." and
commit 839c817ce6
"xhci: Implement HS/FS/LS bandwidth checking."
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
When xhci_mem_cleanup() is called, we can't be sure if the xHC is
actually halted. We can ask the xHC to halt by writing to the RUN bit
in the command register, but that might timeout due to a HW hang.
If the host controller is still running, we should not write zeroed
values to the event ring dequeue pointers or base tables, the DCBAA
pointers, or the command ring pointers. Eric Fu reports his VIA VL800
host accesses the event ring pointers after a failed register restore on
resume from suspend. The hypothesis is that the host never actually
halted before the register write to change the event ring pointer to
zero.
Remove all writes of zeroed values to pointer registers in
xhci_mem_cleanup(). Instead, make all callers of the function reset the
host controller first, which will reset those registers to zero.
xhci_mem_init() is the only caller that doesn't first halt and reset the
host controller before calling xhci_mem_cleanup().
This should be backported to kernels as old as 2.6.32.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: Elric Fu <elricfu1@gmail.com>
Cc: stable@vger.kernel.org
Allocate 2 segments for transfer ring by default, so we can expand the ring
when the enqueue pointer and dequeue pointer are in different segments.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: Paul Zimmerman <Paul.Zimmerman@synopsys.com>
If room_on_ring() check fails, try to expand the ring and check again.
When expand a ring, use a cached ring or allocate new segments, link
the original ring and the new ring or segments, update the original ring's
segment numbers and the last segment pointer.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: Paul Zimmerman <Paul.Zimmerman@synopsys.com>
In the past all the rings were allocated with cycle state equal to 1.
Now the driver may expand an existing ring, and the new segments shall be
allocated with the same cycle state as the old one.
This affects ring allocation and cached ring re-initialization.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: Paul Zimmerman <Paul.Zimmerman@synopsys.com>
Factor out the segments allocation and free part from ring allocation
and free routines since driver may call them directly when try to expand
a ring.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: Paul Zimmerman <Paul.Zimmerman@synopsys.com>
In the past, the room_on_ring() check was implemented by walking all over
the ring, which is wasteful and complicated.
Count the number of free TRBs instead. The free TRBs number should be
updated when enqueue/dequeue pointer is updated, or upon the completion
of a set dequeue pointer command.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: Paul Zimmerman <Paul.Zimmerman@synopsys.com>
Store the ring's last segment pointer and number of segments for ring
expansion usage.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: Paul Zimmerman <Paul.Zimmerman@synopsys.com>
When allocate a ring, store its type - four transfer types for endpoint,
TYPE_STREAM for stream transfer, and TYPE_COMMAND/TYPE_EVENT for xHCI host.
This helps to get rid of three bool function parameters: link_trbs, isoc
and consumer.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: Paul Zimmerman <Paul.Zimmerman@synopsys.com>
This is to pull in the xhci changes and the other fixes and device id
updates that were done in Linus's tree.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The xHCI 0.96 spec says that HS bulk and control endpoint NAK rate must
be encoded as an exponent of two number of microframes. The endpoint
descriptor has the NAK rate encoded in number of microframes. We were
just copying the value from the endpoint descriptor into the endpoint
context interval field, which was not correct. This lead to the VIA
host rejecting the add of a bulk OUT endpoint from any USB 2.0 mass
storage device.
The fix is to use the correct encoding. Refactor the code to convert
number of frames to an exponential number of microframes, and make sure
we convert the number of microframes in HS bulk and control endpoints to
an exponent.
This should be back ported to kernels as old as 2.6.31, that contain the
commit dfa49c4ad1 "USB: xhci - fix math
in xhci_get_endpoint_interval"
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: Felipe Contreras <felipe.contreras@gmail.com>
Suggested-by: Andiry Xu <andiry.xu@amd.com>
Cc: stable@vger.kernel.org
When the USB 3.0 hub support went in, I disabled selective suspend for
all external USB 3.0 hubs because they used a different mechanism to
enable remote wakeup. In fact, other USB 3.0 devices that could signal
remote wakeup would have been prevented from going into suspend because
they would have stalled the SetFeature Device Remote Wakeup request.
This patch adds support for the USB 3.0 way of enabling remote wake up
(with a SetFeature Function Suspend request), and enables selective
suspend for all hubs during hub_probe. It assumes that all USB 3.0 have
only one "function" as defined by the interface association descriptor,
which is true of all the USB 3.0 devices I've seen so far. FIXME if
that turns out to change later.
After a device signals a remote wakeup, it is supposed to send a Device
Notification packet to the host controller, signaling which function
sent the remote wakeup. The host can then put any other functions back
into function suspend. Since we don't have support for function suspend
(and no devices currently support it), we'll just assume the hub
function will resume the device properly when it received the port
status change notification, and simply ignore any device notification
events from the xHCI host controller.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Debuggers only really care what the xHCI driver sets the ring dequeue
pointer to, so make the driver stop babbling about the memory addresses
of internal ring structures. This makes wading through the output of
allocating and freeing 256 stream rings much easier by reducing the
number of output lines per ring from 9 to 1.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Sarah Sharp
Xenia Ragiadakou
Greg Kroah-Hartman
James Hogan
Mathias Nyman
Vladimir Murzin
Sergio Aguirre
Alan Stern
David Howells
Lan Tianyu
Julius Werner
Elric Fu
Takashi Iwai
Oliver Neukum
Andiry Xu