The default size of the ring buffer is too small for machines with a
large amount of CPUs under heavy load. What ends up happening when
debugging is the ring buffer overlaps and chews up old messages making
debugging impossible unless the size is passed as a kernel parameter.
An idle system upon boot up will on average spew out only about one or
two extra lines but where this really matters is on heavy load and that
will vary widely depending on the system and environment.
There are mechanisms to help increase the kernel ring buffer for tracing
through debugfs, and those interfaces even allow growing the kernel ring
buffer per CPU. We also have a static value which can be passed upon
boot. Relying on debugfs however is not ideal for production, and
relying on the value passed upon bootup is can only used *after* an
issue has creeped up. Instead of being reactive this adds a proactive
measure which lets you scale the amount of contributions you'd expect to
the kernel ring buffer under load by each CPU in the worst case
scenario.
We use num_possible_cpus() to avoid complexities which could be
introduced by dynamically changing the ring buffer size at run time,
num_possible_cpus() lets us use the upper limit on possible number of
CPUs therefore avoiding having to deal with hotplugging CPUs on and off.
This introduces the kernel configuration option LOG_CPU_MAX_BUF_SHIFT
which is used to specify the maximum amount of contributions to the
kernel ring buffer in the worst case before the kernel ring buffer flips
over, the size is specified as a power of 2. The total amount of
contributions made by each CPU must be greater than half of the default
kernel ring buffer size (1 << LOG_BUF_SHIFT bytes) in order to trigger
an increase upon bootup. The kernel ring buffer is increased to the
next power of two that would fit the required minimum kernel ring buffer
size plus the additional CPU contribution. For example if LOG_BUF_SHIFT
is 18 (256 KB) you'd require at least 128 KB contributions by other CPUs
in order to trigger an increase of the kernel ring buffer. With a
LOG_CPU_BUF_SHIFT of 12 (4 KB) you'd require at least anything over > 64
possible CPUs to trigger an increase. If you had 128 possible CPUs the
amount of minimum required kernel ring buffer bumps to:
((1 << 18) + ((128 - 1) * (1 << 12))) / 1024 = 764 KB
Since we require the ring buffer to be a power of two the new required
size would be 1024 KB.
This CPU contributions are ignored when the "log_buf_len" kernel
parameter is used as it forces the exact size of the ring buffer to an
expected power of two value.
[pmladek@suse.cz: fix build]
Signed-off-by: Luis R. Rodriguez <mcgrof@suse.com>
Signed-off-by: Petr Mladek <pmladek@suse.cz>
Tested-by: Davidlohr Bueso <davidlohr@hp.com>
Tested-by: Petr Mladek <pmladek@suse.cz>
Reviewed-by: Davidlohr Bueso <davidlohr@hp.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Petr Mladek <pmladek@suse.cz>
Cc: Joe Perches <joe@perches.com>
Cc: Arun KS <arunks.linux@gmail.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Davidlohr Bueso <davidlohr@hp.com>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Jan Kara <jack@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Enabling NO_HZ_FULL currently has the side effect of enabling callback
offloading on all CPUs. This results in lots of additional rcuo kthreads,
and can also increase context switching and wakeups, even in cases where
callback offloading is neither needed nor particularly desirable. This
commit therefore enables callback offloading on a given CPU only if
specifically requested at build time or boot time, or if that CPU has
been specifically designated (again, either at build time or boot time)
as a nohz_full CPU.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Add calibration_delay_done() call and dummy implementation. This allows
architectures to stop accepting registrations for new timer based delay
functions.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
re-add the perm check (we unified the module param and sysfs checks, but
the module ones were stronger so we weakened them temporarily).
Param parsing gets documented, and also "--" now forces args to be
handed to init (and ignored by the kernel).
Module NX/RO protections get tightened: we now set them before calling
parse_args().
Cheers,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJTl+oJAAoJENkgDmzRrbjxtUEP/jIXml01jE2HquOJ/DfrCJOt
ry5L5Iy8wVBRotTszrXqlD6+W8fLYsEdhM65Wof1H7X1qjaulqYZmrL7bQn4rIGN
YPUmO5rOzECeAPNW5+e2JLnR4bmS99gVcWzJFCHUBd7Z8ceKaoIk7/XvUg6Mdjg7
v0kJ5X+U9da2sVYYcZ71euth4ADLFDRNRexA1mPI6mKzJLOBgfvCBWZnkFVdBcjd
VmL6ceFo/yP9Ed4pgG/4uXq1dZ4ZttpjPusDmNcjq+snOzsQb4tW+KB2Pr6iTwQy
TDt7lQm5+xfUXgUG/S5L6PYn10P44Voo7AEJa+QK5YPSOY/eRVA0h4/ayP0vqDaJ
LpZjqXbW77G4yOgEV9KRFLLXiFXykTh2TyCPYL5G2XVXQp1OmViu2f21JWJLFLgL
mqOXYWdowOGVOOoTgwxIdxczCFCATJUaU5Ig6ay8C02E2mCwIV+IaGSdpsCiyjz/
dNNumMxWg0NMo/c0YG4K3Ake6ZaGrwbnuJYijaEj6mgpifhh7k4yhFciXGLpkLnS
Yuo4ORO0GX34z1+bX0iwrgMGPdy7+BnbXsDdWJsbsnwnKKes/Sp44fNl4lPwdM3n
siaPsxmfAtl9EGqbkU1Fk+x5+X/Lv2I/7/nX5n53520RLkJJpbeMDfHUqpbrqeUN
JNUTOZ9o72EqDVKnn175
=IxSN
-----END PGP SIGNATURE-----
Merge tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull module updates from Rusty Russell:
"Most of this is cleaning up various driver sysfs permissions so we can
re-add the perm check (we unified the module param and sysfs checks,
but the module ones were stronger so we weakened them temporarily).
Param parsing gets documented, and also "--" now forces args to be
handed to init (and ignored by the kernel).
Module NX/RO protections get tightened: we now set them before calling
parse_args()"
* tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
module: set nx before marking module MODULE_STATE_COMING.
samples/kobject/: avoid world-writable sysfs files.
drivers/hid/hid-picolcd_fb: avoid world-writable sysfs files.
drivers/staging/speakup/: avoid world-writable sysfs files.
drivers/regulator/virtual: avoid world-writable sysfs files.
drivers/scsi/pm8001/pm8001_ctl.c: avoid world-writable sysfs files.
drivers/hid/hid-lg4ff.c: avoid world-writable sysfs files.
drivers/video/fbdev/sm501fb.c: avoid world-writable sysfs files.
drivers/mtd/devices/docg3.c: avoid world-writable sysfs files.
speakup: fix incorrect perms on speakup_acntsa.c
cpumask.h: silence warning with -Wsign-compare
Documentation: Update kernel-parameters.tx
param: hand arguments after -- straight to init
modpost: Fix resource leak in read_dump()
Pull x86-64 espfix changes from Peter Anvin:
"This is the espfix64 code, which fixes the IRET information leak as
well as the associated functionality problem. With this code applied,
16-bit stack segments finally work as intended even on a 64-bit
kernel.
Consequently, this patchset also removes the runtime option that we
added as an interim measure.
To help the people working on Linux kernels for very small systems,
this patchset also makes these compile-time configurable features"
* 'x86/espfix' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
Revert "x86-64, modify_ldt: Make support for 16-bit segments a runtime option"
x86, espfix: Make it possible to disable 16-bit support
x86, espfix: Make espfix64 a Kconfig option, fix UML
x86, espfix: Fix broken header guard
x86, espfix: Move espfix definitions into a separate header file
x86-32, espfix: Remove filter for espfix32 due to race
x86-64, espfix: Don't leak bits 31:16 of %esp returning to 16-bit stack
1. Remove CLONE_KERNEL, it has no users and it is dangerous.
The (old) comment says "List of flags we want to share for kernel
threads" but this is not true, we do not want to share ->sighand by
default. This flag can only be used if the caller is sure that both
parent/child will never play with signals (say, allow_signal/etc).
2. Change rest_init() to clone kernel_init() without CLONE_SIGHAND.
In this case CLONE_SIGHAND does not really hurt, and it looks like
optimization because copy_sighand() can avoid kmem_cache_alloc().
But in fact this only adds the minor pessimization. kernel_init()
is going to exec the init process, and de_thread() will need to
unshare ->sighand and do kmem_cache_alloc(sighand_cachep) anyway,
but it needs to do more work and take tasklist_lock and siglock.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When a module is built into the kernel the module_init() function
becomes an initcall. Sometimes debugging through dynamic debug can
help, however, debugging built in kernel modules is typically done by
changing the .config, recompiling, and booting the new kernel in an
effort to determine exactly which module caused a problem.
This patchset can be useful stand-alone or combined with initcall_debug.
There are cases where some initcalls can hang the machine before the
console can be flushed, which can make initcall_debug output inaccurate.
Having the ability to skip initcalls can help further debugging of these
scenarios.
Usage: initcall_blacklist=<list of comma separated initcalls>
ex) added "initcall_blacklist=sgi_uv_sysfs_init" as a kernel parameter and
the log contains:
blacklisting initcall sgi_uv_sysfs_init
...
...
initcall sgi_uv_sysfs_init blacklisted
ex) added "initcall_blacklist=foo_bar,sgi_uv_sysfs_init" as a kernel parameter
and the log contains:
blacklisting initcall foo_bar
blacklisting initcall sgi_uv_sysfs_init
...
...
initcall sgi_uv_sysfs_init blacklisted
[akpm@linux-foundation.org: tweak printk text]
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Cc: Richard Weinberger <richard.weinberger@gmail.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Josh Boyer <jwboyer@fedoraproject.org>
Cc: Rob Landley <rob@landley.net>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pertially revert commit ea676e846a ("init/main.c: convert to
pr_foo()").
Unbeknownst to me, pr_debug() is different from the other pr_foo()
levels: pr_debug() is a no-op when DEBUG is not defined.
Happily, init/main.c does have a #define DEBUG so we didn't break
initcall_debug. But the functioning of initcall_debug should not be
dependent upon the presence of that #define DEBUG.
Reported-by: Russell King <rmk@arm.linux.org.uk>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
... instead of naked numbers.
Stuff in sysrq.c used to set it to 8 which is supposed to mean above
default level so set it to DEBUG instead as we're terminating/killing all
tasks and we want to be verbose there.
Also, correct the check in x86_64_start_kernel which should be >= as
we're clearly issuing the string there for all debug levels, not only
the magical 10.
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Kees Cook <keescook@chromium.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Joe Perches <joe@perches.com>
Cc: Valdis Kletnieks <Valdis.Kletnieks@vt.edu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
CONFIG_CROSS_MEMORY_ATTACH adds couple syscalls: process_vm_readv and
process_vm_writev, it's a kind of IPC for copying data between processes.
Currently this option is placed inside "Processor type and features".
This patch moves it into "General setup" (where all other arch-independed
syscalls and ipc features are placed) and changes prompt string to less
cryptic.
Signed-off-by: Konstantin Khlebnikov <koct9i@gmail.com>
Cc: Christopher Yeoh <cyeoh@au1.ibm.com>
Cc: Davidlohr Bueso <davidlohr@hp.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove start_kernel()->mm_init_owner(&init_mm, &init_task).
This doesn't really hurt but unnecessary and misleading. init_task is the
"swapper" thread == current, its ->mm is always NULL. And init_mm can
only be used as ->active_mm, not as ->mm.
mm_init_owner() has a single caller with this patch, perhaps it should
die. mm_init() can initialize ->owner under #ifdef.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Reviewed-by: Michal Hocko <mhocko@suse.cz>
Cc: Balbir Singh <bsingharora@gmail.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Peter Chiang <pchiang@nvidia.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
CONFIG_MM_OWNER makes no sense. It is not user-selectable, it is only
selected by CONFIG_MEMCG automatically. So we can kill this option in
init/Kconfig and do s/CONFIG_MM_OWNER/CONFIG_MEMCG/ globally.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Michal Hocko <mhocko@suse.cz>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Kmemcg is currently under development and lacks some important features.
In particular, it does not have support of kmem reclaim on memory pressure
inside cgroup, which practically makes it unusable in real life. Let's
warn about it in both Kconfig and Documentation to prevent complaints
arising.
Signed-off-by: Vladimir Davydov <vdavydov@parallels.com>
Acked-by: Michal Hocko <mhocko@suse.cz>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge in Linus' tree with:
fa81511bb0 x86-64, modify_ldt: Make support for 16-bit segments a runtime option
... reverted, to avoid a conflict. This commit is no longer necessary
with the proper fix in place.
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
As requested by Linus add explicit __visible to the asmlinkage users.
This marks functions visible to assembler.
Tree sweep for rest of tree.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Link: http://lkml.kernel.org/r/1398984278-29319-4-git-send-email-andi@firstfloor.org
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Make espfix64 a hidden Kconfig option. This fixes the x86-64 UML
build which had broken due to the non-existence of init_espfix_bsp()
in UML: since UML uses its own Kconfig, this option does not appear in
the UML build.
This also makes it possible to make support for 16-bit segments a
configuration option, for the people who want to minimize the size of
the kernel.
Reported-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: Richard Weinberger <richard@nod.at>
Link: http://lkml.kernel.org/r/1398816946-3351-1-git-send-email-hpa@linux.intel.com
The IRET instruction, when returning to a 16-bit segment, only
restores the bottom 16 bits of the user space stack pointer. This
causes some 16-bit software to break, but it also leaks kernel state
to user space. We have a software workaround for that ("espfix") for
the 32-bit kernel, but it relies on a nonzero stack segment base which
is not available in 64-bit mode.
In checkin:
b3b42ac2cb x86-64, modify_ldt: Ban 16-bit segments on 64-bit kernels
we "solved" this by forbidding 16-bit segments on 64-bit kernels, with
the logic that 16-bit support is crippled on 64-bit kernels anyway (no
V86 support), but it turns out that people are doing stuff like
running old Win16 binaries under Wine and expect it to work.
This works around this by creating percpu "ministacks", each of which
is mapped 2^16 times 64K apart. When we detect that the return SS is
on the LDT, we copy the IRET frame to the ministack and use the
relevant alias to return to userspace. The ministacks are mapped
readonly, so if IRET faults we promote #GP to #DF which is an IST
vector and thus has its own stack; we then do the fixup in the #DF
handler.
(Making #GP an IST exception would make the msr_safe functions unsafe
in NMI/MC context, and quite possibly have other effects.)
Special thanks to:
- Andy Lutomirski, for the suggestion of using very small stack slots
and copy (as opposed to map) the IRET frame there, and for the
suggestion to mark them readonly and let the fault promote to #DF.
- Konrad Wilk for paravirt fixup and testing.
- Borislav Petkov for testing help and useful comments.
Reported-by: Brian Gerst <brgerst@gmail.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Link: http://lkml.kernel.org/r/1398816946-3351-1-git-send-email-hpa@linux.intel.com
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Andrew Lutomriski <amluto@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Dirk Hohndel <dirk@hohndel.org>
Cc: Arjan van de Ven <arjan.van.de.ven@intel.com>
Cc: comex <comexk@gmail.com>
Cc: Alexander van Heukelum <heukelum@fastmail.fm>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: <stable@vger.kernel.org> # consider after upstream merge
The kernel passes any args it doesn't need through to init, except it
assumes anything containing '.' belongs to the kernel (for a module).
This change means all users can clearly distinguish which arguments
are for init.
For example, the kernel uses debug ("dee-bug") to mean log everything to
the console, where systemd uses the debug from the Scandinavian "day-boog"
meaning "fail to boot". If a future versions uses argv[] instead of
reading /proc/cmdline, this confusion will be avoided.
eg: test 'FOO="this is --foo"' -- 'systemd.debug="true true true"'
Gives:
argv[0] = '/debug-init'
argv[1] = 'test'
argv[2] = 'systemd.debug=true true true'
envp[0] = 'HOME=/'
envp[1] = 'TERM=linux'
envp[2] = 'FOO=this is --foo'
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
The SYSTEM_TRUSTED_KEYRING config option is not in any menu, causing it
to show up in the toplevel of the kernel configuration. Fix this by
moving it under the General Setup menu.
Signed-off-by: Peter Foley <pefoley2@pefoley.com>
Cc: David Howells <dhowells@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull audit updates from Eric Paris.
* git://git.infradead.org/users/eparis/audit: (28 commits)
AUDIT: make audit_is_compat depend on CONFIG_AUDIT_COMPAT_GENERIC
audit: renumber AUDIT_FEATURE_CHANGE into the 1300 range
audit: do not cast audit_rule_data pointers pointlesly
AUDIT: Allow login in non-init namespaces
audit: define audit_is_compat in kernel internal header
kernel: Use RCU_INIT_POINTER(x, NULL) in audit.c
sched: declare pid_alive as inline
audit: use uapi/linux/audit.h for AUDIT_ARCH declarations
syscall_get_arch: remove useless function arguments
audit: remove stray newline from audit_log_execve_info() audit_panic() call
audit: remove stray newlines from audit_log_lost messages
audit: include subject in login records
audit: remove superfluous new- prefix in AUDIT_LOGIN messages
audit: allow user processes to log from another PID namespace
audit: anchor all pid references in the initial pid namespace
audit: convert PPIDs to the inital PID namespace.
pid: get pid_t ppid of task in init_pid_ns
audit: rename the misleading audit_get_context() to audit_take_context()
audit: Add generic compat syscall support
audit: Add CONFIG_HAVE_ARCH_AUDITSYSCALL
...
This can greatly aid in narrowing down the real source of initramfs
problems such as failures related to the compression of the in-kernel
initramfs when an external initramfs is in use as well. Existing errors
are ambiguous as to which initramfs is a problem and why.
[akpm@linux-foundation.org: use pr_debug()]
Signed-off-by: Daniel M. Weeks <dan@danweeks.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
"make allnoconfig" exists to ease testing of minimal configurations.
Documentation/SubmitChecklist includes a note to test with allnoconfig.
This helps catch missing dependencies on common-but-not-required
functionality, which might otherwise go unnoticed.
However, allnoconfig still leaves many symbols enabled, because they're
hidden behind CONFIG_EMBEDDED or CONFIG_EXPERT. For instance, allnoconfig
still has CONFIG_PRINTK and CONFIG_BLOCK enabled, so drivers don't
typically get build-tested with those disabled.
To address this, introduce a new Kconfig option "allnoconfig_y", used on
symbols which only exist to hide other symbols. Set it on CONFIG_EMBEDDED
(which then selects CONFIG_EXPERT). allnoconfig will then disable all the
symbols hidden behind those.
Signed-off-by: Josh Triplett <josh@joshtriplett.org>
Tested-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Michal Marek <mmarek@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge first patch-bomb from Andrew Morton:
- Various misc bits
- kmemleak fixes
- small befs, codafs, cifs, efs, freexxfs, hfsplus, minixfs, reiserfs things
- fanotify
- I appear to have become SuperH maintainer
- ocfs2 updates
- direct-io tweaks
- a bit of the MM queue
- printk updates
- MAINTAINERS maintenance
- some backlight things
- lib/ updates
- checkpatch updates
- the rtc queue
- nilfs2 updates
- Small Documentation/ updates
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (237 commits)
Documentation/SubmittingPatches: remove references to patch-scripts
Documentation/SubmittingPatches: update some dead URLs
Documentation/filesystems/ntfs.txt: remove changelog reference
Documentation/kmemleak.txt: updates
fs/reiserfs/super.c: add __init to init_inodecache
fs/reiserfs: move prototype declaration to header file
fs/hfsplus/attributes.c: add __init to hfsplus_create_attr_tree_cache()
fs/hfsplus/extents.c: fix concurrent acess of alloc_blocks
fs/hfsplus/extents.c: remove unused variable in hfsplus_get_block
nilfs2: update project's web site in nilfs2.txt
nilfs2: update MAINTAINERS file entries fix
nilfs2: verify metadata sizes read from disk
nilfs2: add FITRIM ioctl support for nilfs2
nilfs2: add nilfs_sufile_trim_fs to trim clean segs
nilfs2: implementation of NILFS_IOCTL_SET_SUINFO ioctl
nilfs2: add nilfs_sufile_set_suinfo to update segment usage
nilfs2: add struct nilfs_suinfo_update and flags
nilfs2: update MAINTAINERS file entries
fs/coda/inode.c: add __init to init_inodecache()
BEFS: logging cleanup
...
uselib hasn't been used since libc5; glibc does not use it. Support
turning it off.
When disabled, also omit the load_elf_library implementation from
binfmt_elf.c, which only uselib invokes.
bloat-o-meter:
add/remove: 0/4 grow/shrink: 0/1 up/down: 0/-785 (-785)
function old new delta
padzero 39 36 -3
uselib_flags 20 - -20
sys_uselib 168 - -168
SyS_uselib 168 - -168
load_elf_library 426 - -426
The new CONFIG_USELIB defaults to `y'.
Signed-off-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
sys_sysfs is an obsolete system call no longer supported by libc.
- This patch adds a default CONFIG_SYSFS_SYSCALL=y
- Option can be turned off in expert mode.
- cond_syscall added to kernel/sys_ni.c
[akpm@linux-foundation.org: tweak Kconfig help text]
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Cc: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull cgroup updates from Tejun Heo:
"A lot updates for cgroup:
- The biggest one is cgroup's conversion to kernfs. cgroup took
after the long abandoned vfs-entangled sysfs implementation and
made it even more convoluted over time. cgroup's internal objects
were fused with vfs objects which also brought in vfs locking and
object lifetime rules. Naturally, there are places where vfs rules
don't fit and nasty hacks, such as credential switching or lock
dance interleaving inode mutex and cgroup_mutex with object serial
number comparison thrown in to decide whether the operation is
actually necessary, needed to be employed.
After conversion to kernfs, internal object lifetime and locking
rules are mostly isolated from vfs interactions allowing shedding
of several nasty hacks and overall simplification. This will also
allow implmentation of operations which may affect multiple cgroups
which weren't possible before as it would have required nesting
i_mutexes.
- Various simplifications including dropping of module support,
easier cgroup name/path handling, simplified cgroup file type
handling and task_cg_lists optimization.
- Prepatory changes for the planned unified hierarchy, which is still
a patchset away from being actually operational. The dummy
hierarchy is updated to serve as the default unified hierarchy.
Controllers which aren't claimed by other hierarchies are
associated with it, which BTW was what the dummy hierarchy was for
anyway.
- Various fixes from Li and others. This pull request includes some
patches to add missing slab.h to various subsystems. This was
triggered xattr.h include removal from cgroup.h. cgroup.h
indirectly got included a lot of files which brought in xattr.h
which brought in slab.h.
There are several merge commits - one to pull in kernfs updates
necessary for converting cgroup (already in upstream through
driver-core), others for interfering changes in the fixes branch"
* 'for-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup: (74 commits)
cgroup: remove useless argument from cgroup_exit()
cgroup: fix spurious lockdep warning in cgroup_exit()
cgroup: Use RCU_INIT_POINTER(x, NULL) in cgroup.c
cgroup: break kernfs active_ref protection in cgroup directory operations
cgroup: fix cgroup_taskset walking order
cgroup: implement CFTYPE_ONLY_ON_DFL
cgroup: make cgrp_dfl_root mountable
cgroup: drop const from @buffer of cftype->write_string()
cgroup: rename cgroup_dummy_root and related names
cgroup: move ->subsys_mask from cgroupfs_root to cgroup
cgroup: treat cgroup_dummy_root as an equivalent hierarchy during rebinding
cgroup: remove NULL checks from [pr_cont_]cgroup_{name|path}()
cgroup: use cgroup_setup_root() to initialize cgroup_dummy_root
cgroup: reorganize cgroup bootstrapping
cgroup: relocate setting of CGRP_DEAD
cpuset: use rcu_read_lock() to protect task_cs()
cgroup_freezer: document freezer_fork() subtleties
cgroup: update cgroup_transfer_tasks() to either succeed or fail
cgroup: drop task_lock() protection around task->cgroups
cgroup: update how a newly forked task gets associated with css_set
...
Pull core locking updates from Ingo Molnar:
"The biggest change is the MCS spinlock generalization changes from Tim
Chen, Peter Zijlstra, Jason Low et al. There's also lockdep
fixes/enhancements from Oleg Nesterov, in particular a false negative
fix related to lockdep_set_novalidate_class() usage"
* 'core-locking-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (22 commits)
locking/mutex: Fix debug checks
locking/mutexes: Add extra reschedule point
locking/mutexes: Introduce cancelable MCS lock for adaptive spinning
locking/mutexes: Unlock the mutex without the wait_lock
locking/mutexes: Modify the way optimistic spinners are queued
locking/mutexes: Return false if task need_resched() in mutex_can_spin_on_owner()
locking: Move mcs_spinlock.h into kernel/locking/
m68k: Skip futex_atomic_cmpxchg_inatomic() test
futex: Allow architectures to skip futex_atomic_cmpxchg_inatomic() test
Revert "sched/wait: Suppress Sparse 'variable shadowing' warning"
lockdep: Change lockdep_set_novalidate_class() to use _and_name
lockdep: Change mark_held_locks() to check hlock->check instead of lockdep_no_validate
lockdep: Don't create the wrong dependency on hlock->check == 0
lockdep: Make held_lock->check and "int check" argument bool
locking/mcs: Allow architecture specific asm files to be used for contended case
locking/mcs: Order the header files in Kbuild of each architecture in alphabetical order
sched/wait: Suppress Sparse 'variable shadowing' warning
hung_task/Documentation: Fix hung_task_warnings description
locking/mcs: Allow architectures to hook in to contended paths
locking/mcs: Micro-optimize the MCS code, add extra comments
...
Currently AUDITSYSCALL has a long list of architecture depencency:
depends on AUDIT && (X86 || PARISC || PPC || S390 || IA64 || UML ||
SPARC64 || SUPERH || (ARM && AEABI && !OABI_COMPAT) || ALPHA)
The purpose of this patch is to replace it with HAVE_ARCH_AUDITSYSCALL
for simplicity.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Acked-by: Will Deacon <will.deacon@arm.com> (arm)
Acked-by: Richard Guy Briggs <rgb@redhat.com> (audit)
Acked-by: Matt Turner <mattst88@gmail.com> (alpha)
Acked-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Signed-off-by: Eric Paris <eparis@redhat.com>
Commit 73f7d1ca32 (ACPI / init: Run acpi_early_init() before
timekeeping_init()) optimistically moved the early ACPI initialization
before timekeeping_init(), but that didn't work, because it broke fast
TSC calibration for Julian Wollrath on Thinkpad x121e (and most likely
for others too). The reason is that acpi_early_init() enables the SCI
and that interferes with the fast TSC calibration mechanism.
Thus follow the original idea to execute acpi_early_init() before
efi_enter_virtual_mode() to help the EFI people for now and we can
revisit the other problem that commit 73f7d1ca32 attempted to
address in the future (if really necessary).
Fixes: 73f7d1ca32 (ACPI / init: Run acpi_early_init() before timekeeping_init())
Reported-by: Julian Wollrath <jwollrath@web.de>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
If an architecture has futex_atomic_cmpxchg_inatomic() implemented and there
is no runtime check necessary, allow to skip the test within futex_init().
This allows to get rid of some code which would always give the same result,
and also allows the compiler to optimize a couple of if statements away.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Finn Thain <fthain@telegraphics.com.au>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Link: http://lkml.kernel.org/r/20140302120947.GA3641@osiris
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
cgroup filesystem code was derived from the original sysfs
implementation which was heavily intertwined with vfs objects and
locking with the goal of re-using the existing vfs infrastructure.
That experiment turned out rather disastrous and sysfs switched, a
long time ago, to distributed filesystem model where a separate
representation is maintained which is queried by vfs. Unfortunately,
cgroup stuck with the failed experiment all these years and
accumulated even more problems over time.
Locking and object lifetime management being entangled with vfs is
probably the most egregious. vfs is never designed to be misused like
this and cgroup ends up jumping through various convoluted dancing to
make things work. Even then, operations across multiple cgroups can't
be done safely as it'll deadlock with rename locking.
Recently, kernfs is separated out from sysfs so that it can be used by
users other than sysfs. This patch converts cgroup to use kernfs,
which will bring the following benefits.
* Separation from vfs internals. Locking and object lifetime
management is contained in cgroup proper making things a lot
simpler. This removes significant amount of locking convolutions,
hairy object lifetime rules and the restriction on multi-cgroup
operations.
* Can drop a lot of code to implement filesystem interface as most are
provided by kernfs.
* Proper "severing" semantics, which allows controllers to not worry
about lingering file accesses after offline.
While the preceding patches did as much as possible to make the
transition less painful, large part of the conversion has to be one
discrete step making this patch rather large. The rest of the commit
message lists notable changes in different areas.
Overall
-------
* vfs constructs replaced with kernfs ones. cgroup->dentry w/ ->kn,
cgroupfs_root->sb w/ ->kf_root.
* All dentry accessors are removed. Helpers to map from kernfs
constructs are added.
* All vfs plumbing around dentry, inode and bdi removed.
* cgroup_mount() now directly looks for matching root and then
proceeds to create a new one if not found.
Synchronization and object lifetime
-----------------------------------
* vfs inode locking removed. Among other things, this removes the
need for the convolution in cgroup_cfts_commit(). Future patches
will further simplify it.
* vfs refcnting replaced with cgroup internal ones. cgroup->refcnt,
cgroupfs_root->refcnt added. cgroup_put_root() now directly puts
root->refcnt and when it reaches zero proceeds to destroy it thus
merging cgroup_put_root() and the former cgroup_kill_sb().
Simliarly, cgroup_put() now directly schedules cgroup_free_rcu()
when refcnt reaches zero.
* Unlike before, kernfs objects don't hold onto cgroup objects. When
cgroup destroys a kernfs node, all existing operations are drained
and the association is broken immediately. The same for
cgroupfs_roots and mounts.
* All operations which come through kernfs guarantee that the
associated cgroup is and stays valid for the duration of operation;
however, there are two paths which need to find out the associated
cgroup from dentry without going through kernfs -
css_tryget_from_dir() and cgroupstats_build(). For these two,
kernfs_node->priv is RCU managed so that they can dereference it
under RCU read lock.
File and directory handling
---------------------------
* File and directory operations converted to kernfs_ops and
kernfs_syscall_ops.
* xattrs is implicitly supported by kernfs. No need to worry about it
from cgroup. This means that "xattr" mount option is no longer
necessary. A future patch will add a deprecated warning message
when sane_behavior.
* When cftype->max_write_len > PAGE_SIZE, it's necessary to make a
private copy of one of the kernfs_ops to set its atomic_write_len.
cftype->kf_ops is added and cgroup_init/exit_cftypes() are updated
to handle it.
* cftype->lockdep_key added so that kernfs lockdep annotation can be
per cftype.
* Inidividual file entries and open states are now managed by kernfs.
No need to worry about them from cgroup. cfent, cgroup_open_file
and their friends are removed.
* kernfs_nodes are created deactivated and kernfs_activate()
invocations added to places where creation of new nodes are
committed.
* cgroup_rmdir() uses kernfs_[un]break_active_protection() for
self-removal.
v2: - Li pointed out in an earlier patch that specifying "name="
during mount without subsystem specification should succeed if
there's an existing hierarchy with a matching name although it
should fail with -EINVAL if a new hierarchy should be created.
Prior to the conversion, this used by handled by deferring
failure from NULL return from cgroup_root_from_opts(), which was
necessary because root was being created before checking for
existing ones. Note that cgroup_root_from_opts() returned an
ERR_PTR() value for error conditions which require immediate
mount failure.
As we now have separate search and creation steps, deferring
failure from cgroup_root_from_opts() is no longer necessary.
cgroup_root_from_opts() is updated to always return ERR_PTR()
value on failure.
- The logic to match existing roots is updated so that a mount
attempt with a matching name but different subsys_mask are
rejected. This was handled by a separate matching loop under
the comment "Check for name clashes with existing mounts" but
got lost during conversion. Merge the check into the main
search loop.
- Add __rcu __force casting in RCU_INIT_POINTER() in
cgroup_destroy_locked() to avoid the sparse address space
warning reported by kbuild test bot. Maybe we want an explicit
interface to use kn->priv as RCU protected pointer?
v3: Make CONFIG_CGROUPS select CONFIG_KERNFS.
v4: Rebased on top of 0ab02ca8f8 ("cgroup: protect modifications to
cgroup_idr with cgroup_mutex").
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Li Zefan <lizefan@huawei.com>
Cc: kbuild test robot fengguang.wu@intel.com>
This changes 'do_execve()' to get the executable name as a 'struct
filename', and to free it when it is done. This is what the normal
users want, and it simplifies and streamlines their error handling.
The controlled lifetime of the executable name also fixes a
use-after-free problem with the trace_sched_process_exec tracepoint: the
lifetime of the passed-in string for kernel users was not at all
obvious, and the user-mode helper code used UMH_WAIT_EXEC to serialize
the pathname allocation lifetime with the execve() having finished,
which in turn meant that the trace point that happened after
mm_release() of the old process VM ended up using already free'd memory.
To solve the kernel string lifetime issue, this simply introduces
"getname_kernel()" that works like the normal user-space getname()
function, except with the source coming from kernel memory.
As Oleg points out, this also means that we could drop the tcomm[] array
from 'struct linux_binprm', since the pathname lifetime now covers
setup_new_exec(). That would be a separate cleanup.
Reported-by: Igor Zhbanov <i.zhbanov@samsung.com>
Tested-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull vfs updates from Al Viro:
"Assorted stuff; the biggest pile here is Christoph's ACL series. Plus
assorted cleanups and fixes all over the place...
There will be another pile later this week"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (43 commits)
__dentry_path() fixes
vfs: Remove second variable named error in __dentry_path
vfs: Is mounted should be testing mnt_ns for NULL or error.
Fix race when checking i_size on direct i/o read
hfsplus: remove can_set_xattr
nfsd: use get_acl and ->set_acl
fs: remove generic_acl
nfs: use generic posix ACL infrastructure for v3 Posix ACLs
gfs2: use generic posix ACL infrastructure
jfs: use generic posix ACL infrastructure
xfs: use generic posix ACL infrastructure
reiserfs: use generic posix ACL infrastructure
ocfs2: use generic posix ACL infrastructure
jffs2: use generic posix ACL infrastructure
hfsplus: use generic posix ACL infrastructure
f2fs: use generic posix ACL infrastructure
ext2/3/4: use generic posix ACL infrastructure
btrfs: use generic posix ACL infrastructure
fs: make posix_acl_create more useful
fs: make posix_acl_chmod more useful
...
mca_init() no longer exists.
sbus_init() is defined in arch/sparc/kernel/sbus.c and is a subsys_initcall.
both are not needed in main.c any more.
Signed-off-by: Kang Hu <hukangustc@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull user namespaces work from Eric Biederman:
"The work to convert the kernel to use kuid_t and kgid_t has been
finished since 3.12 so it is time to remove the scaffolding that
allowed the work to progress incrementally.
The first patch on this branch just removes the scaffolding, ensuring
we will always get compile errors if people accidentally try the
userspace and the kernel uid and gid types. The second patch an
overlooked and unused chunk of mips code that that fails to build
after the first patch.
The code hasn't been in linux-next for long (as I was out of it and
could not sheppared the cold properly) but the patch has been around
for a long time just waiting for the day when I had finished the
uid/gid conversions. Putting the code in linux-next did find the
compile failure on mips so I took the time to get that fix reviewed
and included. Beyond that I am not too worried about errors because
all these two patches do is delete a modest amount of code"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
MIPS: VPE: Remove vpe_getuid and vpe_getgid
userns: userns: Remove UIDGID_STRICT_TYPE_CHECKS
- ACPI core changes to make it create a struct acpi_device object for every
device represented in the ACPI tables during all namespace scans regardless
of the current status of that device. In accordance with this, ACPI hotplug
operations will not delete those objects, unless the underlying ACPI tables
go away.
- On top of the above, new sysfs attribute for ACPI device objects allowing
user space to check device status by triggering the execution of _STA for
its ACPI object. From Srinivas Pandruvada.
- ACPI core hotplug changes reducing code duplication, integrating the
PCI root hotplug with the core and reworking container hotplug.
- ACPI core simplifications making it use ACPI_COMPANION() in the code
"glueing" ACPI device objects to "physical" devices.
- ACPICA update to upstream version 20131218. This adds support for the
DBG2 and PCCT tables to ACPICA, fixes some bugs and improves debug
facilities. From Bob Moore, Lv Zheng and Betty Dall.
- Init code change to carry out the early ACPI initialization earlier.
That should allow us to use ACPI during the timekeeping initialization
and possibly to simplify the EFI initialization too. From Chun-Yi Lee.
- Clenups of the inclusions of ACPI headers in many places all over from
Lv Zheng and Rashika Kheria (work in progress).
- New helper for ACPI _DSM execution and rework of the code in drivers
that uses _DSM to execute it via the new helper. From Jiang Liu.
- New Win8 OSI blacklist entries from Takashi Iwai.
- Assorted ACPI fixes and cleanups from Al Stone, Emil Goode, Hanjun Guo,
Lan Tianyu, Masanari Iida, Oliver Neukum, Prarit Bhargava, Rashika Kheria,
Tang Chen, Zhang Rui.
- intel_pstate driver updates, including proper Baytrail support, from
Dirk Brandewie and intel_pstate documentation from Ramkumar Ramachandra.
- Generic CPU boost ("turbo") support for cpufreq from Lukasz Majewski.
- powernow-k6 cpufreq driver fixes from Mikulas Patocka.
- cpufreq core fixes and cleanups from Viresh Kumar, Jane Li, Mark Brown.
- Assorted cpufreq drivers fixes and cleanups from Anson Huang, John Tobias,
Paul Bolle, Paul Walmsley, Sachin Kamat, Shawn Guo, Viresh Kumar.
- cpuidle cleanups from Bartlomiej Zolnierkiewicz.
- Support for hibernation APM events from Bin Shi.
- Hibernation fix to avoid bringing up nonboot CPUs with ACPI EC disabled
during thaw transitions from Bjørn Mork.
- PM core fixes and cleanups from Ben Dooks, Leonardo Potenza, Ulf Hansson.
- PNP subsystem fixes and cleanups from Dmitry Torokhov, Levente Kurusa,
Rashika Kheria.
- New tool for profiling system suspend from Todd E Brandt and a cpupower
tool cleanup from One Thousand Gnomes.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=dRf6
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
"As far as the number of commits goes, the top spot belongs to ACPI
this time with cpufreq in the second position and a handful of PM
core, PNP and cpuidle updates. They are fixes and cleanups mostly, as
usual, with a couple of new features in the mix.
The most visible change is probably that we will create struct
acpi_device objects (visible in sysfs) for all devices represented in
the ACPI tables regardless of their status and there will be a new
sysfs attribute under those objects allowing user space to check that
status via _STA.
Consequently, ACPI device eject or generally hot-removal will not
delete those objects, unless the table containing the corresponding
namespace nodes is unloaded, which is extremely rare. Also ACPI
container hotplug will be handled quite a bit differently and cpufreq
will support CPU boost ("turbo") generically and not only in the
acpi-cpufreq driver.
Specifics:
- ACPI core changes to make it create a struct acpi_device object for
every device represented in the ACPI tables during all namespace
scans regardless of the current status of that device. In
accordance with this, ACPI hotplug operations will not delete those
objects, unless the underlying ACPI tables go away.
- On top of the above, new sysfs attribute for ACPI device objects
allowing user space to check device status by triggering the
execution of _STA for its ACPI object. From Srinivas Pandruvada.
- ACPI core hotplug changes reducing code duplication, integrating
the PCI root hotplug with the core and reworking container hotplug.
- ACPI core simplifications making it use ACPI_COMPANION() in the
code "glueing" ACPI device objects to "physical" devices.
- ACPICA update to upstream version 20131218. This adds support for
the DBG2 and PCCT tables to ACPICA, fixes some bugs and improves
debug facilities. From Bob Moore, Lv Zheng and Betty Dall.
- Init code change to carry out the early ACPI initialization
earlier. That should allow us to use ACPI during the timekeeping
initialization and possibly to simplify the EFI initialization too.
From Chun-Yi Lee.
- Clenups of the inclusions of ACPI headers in many places all over
from Lv Zheng and Rashika Kheria (work in progress).
- New helper for ACPI _DSM execution and rework of the code in
drivers that uses _DSM to execute it via the new helper. From
Jiang Liu.
- New Win8 OSI blacklist entries from Takashi Iwai.
- Assorted ACPI fixes and cleanups from Al Stone, Emil Goode, Hanjun
Guo, Lan Tianyu, Masanari Iida, Oliver Neukum, Prarit Bhargava,
Rashika Kheria, Tang Chen, Zhang Rui.
- intel_pstate driver updates, including proper Baytrail support,
from Dirk Brandewie and intel_pstate documentation from Ramkumar
Ramachandra.
- Generic CPU boost ("turbo") support for cpufreq from Lukasz
Majewski.
- powernow-k6 cpufreq driver fixes from Mikulas Patocka.
- cpufreq core fixes and cleanups from Viresh Kumar, Jane Li, Mark
Brown.
- Assorted cpufreq drivers fixes and cleanups from Anson Huang, John
Tobias, Paul Bolle, Paul Walmsley, Sachin Kamat, Shawn Guo, Viresh
Kumar.
- cpuidle cleanups from Bartlomiej Zolnierkiewicz.
- Support for hibernation APM events from Bin Shi.
- Hibernation fix to avoid bringing up nonboot CPUs with ACPI EC
disabled during thaw transitions from Bjørn Mork.
- PM core fixes and cleanups from Ben Dooks, Leonardo Potenza, Ulf
Hansson.
- PNP subsystem fixes and cleanups from Dmitry Torokhov, Levente
Kurusa, Rashika Kheria.
- New tool for profiling system suspend from Todd E Brandt and a
cpupower tool cleanup from One Thousand Gnomes"
* tag 'pm+acpi-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (153 commits)
thermal: exynos: boost: Automatic enable/disable of BOOST feature (at Exynos4412)
cpufreq: exynos4x12: Change L0 driver data to CPUFREQ_BOOST_FREQ
Documentation: cpufreq / boost: Update BOOST documentation
cpufreq: exynos: Extend Exynos cpufreq driver to support boost
cpufreq / boost: Kconfig: Support for software-managed BOOST
acpi-cpufreq: Adjust the code to use the common boost attribute
cpufreq: Add boost frequency support in core
intel_pstate: Add trace point to report internal state.
cpufreq: introduce cpufreq_generic_get() routine
ARM: SA1100: Create dummy clk_get_rate() to avoid build failures
cpufreq: stats: create sysfs entries when cpufreq_stats is a module
cpufreq: stats: free table and remove sysfs entry in a single routine
cpufreq: stats: remove hotplug notifiers
cpufreq: stats: handle cpufreq_unregister_driver() and suspend/resume properly
cpufreq: speedstep: remove unused speedstep_get_state
platform: introduce OF style 'modalias' support for platform bus
PM / tools: new tool for suspend/resume performance optimization
ACPI: fix module autoloading for ACPI enumerated devices
ACPI: add module autoloading support for ACPI enumerated devices
ACPI: fix create_modalias() return value handling
...
Use constant format string in case message changes.
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Its user was removed in v2.5.2.4.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge first patch-bomb from Andrew Morton:
- a couple of misc things
- inotify/fsnotify work from Jan
- ocfs2 updates (partial)
- about half of MM
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (117 commits)
mm/migrate: remove unused function, fail_migrate_page()
mm/migrate: remove putback_lru_pages, fix comment on putback_movable_pages
mm/migrate: correct failure handling if !hugepage_migration_support()
mm/migrate: add comment about permanent failure path
mm, page_alloc: warn for non-blockable __GFP_NOFAIL allocation failure
mm: compaction: reset scanner positions immediately when they meet
mm: compaction: do not mark unmovable pageblocks as skipped in async compaction
mm: compaction: detect when scanners meet in isolate_freepages
mm: compaction: reset cached scanner pfn's before reading them
mm: compaction: encapsulate defer reset logic
mm: compaction: trace compaction begin and end
memcg, oom: lock mem_cgroup_print_oom_info
sched: add tracepoints related to NUMA task migration
mm: numa: do not automatically migrate KSM pages
mm: numa: trace tasks that fail migration due to rate limiting
mm: numa: limit scope of lock for NUMA migrate rate limiting
mm: numa: make NUMA-migrate related functions static
lib/show_mem.c: show num_poisoned_pages when oom
mm/hwpoison: add '#' to hwpoison_inject
mm/memblock: use WARN_ONCE when MAX_NUMNODES passed as input parameter
...
Pull cgroup updates from Tejun Heo:
"The bulk of changes are cleanups and preparations for the upcoming
kernfs conversion.
- cgroup_event mechanism which is and will be used only by memcg is
moved to memcg.
- pidlist handling is updated so that it can be served by seq_file.
Also, the list is not sorted if sane_behavior. cgroup
documentation explicitly states that the file is not sorted but it
has been for quite some time.
- All cgroup file handling now happens on top of seq_file. This is
to prepare for kernfs conversion. In addition, all operations are
restructured so that they map 1-1 to kernfs operations.
- Other cleanups and low-pri fixes"
* 'for-3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup: (40 commits)
cgroup: trivial style updates
cgroup: remove stray references to css_id
doc: cgroups: Fix typo in doc/cgroups
cgroup: fix fail path in cgroup_load_subsys()
cgroup: fix missing unlock on error in cgroup_load_subsys()
cgroup: remove for_each_root_subsys()
cgroup: implement for_each_css()
cgroup: factor out cgroup_subsys_state creation into create_css()
cgroup: combine css handling loops in cgroup_create()
cgroup: reorder operations in cgroup_create()
cgroup: make for_each_subsys() useable under cgroup_root_mutex
cgroup: css iterations and css_from_dir() are safe under cgroup_mutex
cgroup: unify pidlist and other file handling
cgroup: replace cftype->read_seq_string() with cftype->seq_show()
cgroup: attach cgroup_open_file to all cgroup files
cgroup: generalize cgroup_pidlist_open_file
cgroup: unify read path so that seq_file is always used
cgroup: unify cgroup_write_X64() and cgroup_write_string()
cgroup: remove cftype->read(), ->read_map() and ->write()
hugetlb_cgroup: convert away from cftype->read()
...
Switch to memblock interfaces for early memory allocator instead of
bootmem allocator. No functional change in beahvior than what it is in
current code from bootmem users points of view.
Archs already converted to NO_BOOTMEM now directly use memblock
interfaces instead of bootmem wrappers build on top of memblock. And
the archs which still uses bootmem, these new apis just fall back to
exiting bootmem APIs.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If DEBUG_SPINLOCK and DEBUG_LOCK_ALLOC are enabled spinlock_t on x86_64
is 72 bytes. For page->ptl they will be allocated from kmalloc-96 slab,
so we loose 24 on each. An average system can easily allocate few tens
thousands of page->ptl and overhead is significant.
Let's create a separate slab for page->ptl allocation to solve this.
To make sure that it really works this time, some numbers from my test
machine (just booted, no load):
Before:
# grep '^\(kmalloc-96\|page->ptl\)' /proc/slabinfo
kmalloc-96 31987 32190 128 30 1 : tunables 120 60 8 : slabdata 1073 1073 92
After:
# grep '^\(kmalloc-96\|page->ptl\)' /proc/slabinfo
page->ptl 27516 28143 72 53 1 : tunables 120 60 8 : slabdata 531 531 9
kmalloc-96 3853 5280 128 30 1 : tunables 120 60 8 : slabdata 176 176 0
Note that the patch is useful not only for debug case, but also for
PREEMPT_RT, where spinlock_t is always bloated.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is a variant patch from Rafael J. Wysocki's
ACPI / init: Run acpi_early_init() before efi_enter_virtual_mode()
According to Matt Fleming, if acpi_early_init() was executed before
efi_enter_virtual_mode(), the EFI initialization could benefit from
it, so Rafael's patch makes that happen.
And, we want accessing ACPI TAD device to set system clock, so move
acpi_early_init() before timekeeping_init(). This final position is
also before efi_enter_virtual_mode().
Tested-by: Toshi Kani <toshi.kani@hp.com>
Signed-off-by: Lee, Chun-Yi <jlee@suse.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Introduce mul_u64_u32_shr() as proposed by Andy a while back; it
allows using 64x64->128 muls on 64bit archs and recent GCC
which defines __SIZEOF_INT128__ and __int128.
(This new method will be used by the scheduler.)
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Cc: fweisbec@gmail.com
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/n/tip-hxjoeuzmrcaumR0uZwjpe2pv@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Removing UIDGID_STRICT_TYPE_CHECKS simplifies the code and always
generates a compile error if the uids and kuids or gids and kgids are
mixed by accident. Now that the appropriate conversions have been
placed throughout the kernel there is no longer a need for a mode where
we don't detect them as compile errors.
Acked-by: Serge Hallyn <serge.hallyn@canonical.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Merge v3.12 based patch series to move cgroup_event implementation to
memcg into for-3.14. The following two commits cause a conflict in
kernel/cgroup.c
2ff2a7d03b ("cgroup: kill css_id")
79bd9814e5 ("cgroup, memcg: move cgroup_event implementation to memcg")
Each patch removes a struct definition from kernel/cgroup.c. As the
two are adjacent, they cause a context conflict. Easily resolved by
removing both structs.
Signed-off-by: Tejun Heo <tj@kernel.org>
cgroup_event is way over-designed and tries to build a generic
flexible event mechanism into cgroup - fully customizable event
specification for each user of the interface. This is utterly
unnecessary and overboard especially in the light of the planned
unified hierarchy as there's gonna be single agent. Simply generating
events at fixed points, or if that's too restrictive, configureable
cadence or single set of configureable points should be enough.
Thankfully, memcg is the only user and gets to keep it. Replacing it
with something simpler on sane_behavior is strongly recommended.
This patch moves cgroup_event and "cgroup.event_control"
implementation to mm/memcontrol.c. Clearing of events on cgroup
destruction is moved from cgroup_destroy_locked() to
mem_cgroup_css_offline(), which shouldn't make any noticeable
difference.
cgroup_css() and __file_cft() are exported to enable the move;
however, this will soon be reverted once the event code is updated to
be memcg specific.
Note that "cgroup.event_control" will now exist only on the hierarchy
with memcg attached to it. While this change is visible to userland,
it is unlikely to be noticeable as the file has never been meaningful
outside memcg.
Aside from the above change, this is pure code relocation.
v2: Per Li Zefan's comments, init/Kconfig updated accordingly and
poll.h inclusion moved from cgroup.c to memcontrol.c.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Li Zefan <lizefan@huawei.com>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Michal Hocko <mhocko@suse.cz>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Balbir Singh <bsingharora@gmail.com>
Pull security subsystem updates from James Morris:
"In this patchset, we finally get an SELinux update, with Paul Moore
taking over as maintainer of that code.
Also a significant update for the Keys subsystem, as well as
maintenance updates to Smack, IMA, TPM, and Apparmor"
and since I wanted to know more about the updates to key handling,
here's the explanation from David Howells on that:
"Okay. There are a number of separate bits. I'll go over the big bits
and the odd important other bit, most of the smaller bits are just
fixes and cleanups. If you want the small bits accounting for, I can
do that too.
(1) Keyring capacity expansion.
KEYS: Consolidate the concept of an 'index key' for key access
KEYS: Introduce a search context structure
KEYS: Search for auth-key by name rather than target key ID
Add a generic associative array implementation.
KEYS: Expand the capacity of a keyring
Several of the patches are providing an expansion of the capacity of a
keyring. Currently, the maximum size of a keyring payload is one page.
Subtract a small header and then divide up into pointers, that only gives
you ~500 pointers on an x86_64 box. However, since the NFS idmapper uses
a keyring to store ID mapping data, that has proven to be insufficient to
the cause.
Whatever data structure I use to handle the keyring payload, it can only
store pointers to keys, not the keys themselves because several keyrings
may point to a single key. This precludes inserting, say, and rb_node
struct into the key struct for this purpose.
I could make an rbtree of records such that each record has an rb_node
and a key pointer, but that would use four words of space per key stored
in the keyring. It would, however, be able to use much existing code.
I selected instead a non-rebalancing radix-tree type approach as that
could have a better space-used/key-pointer ratio. I could have used the
radix tree implementation that we already have and insert keys into it by
their serial numbers, but that means any sort of search must iterate over
the whole radix tree. Further, its nodes are a bit on the capacious side
for what I want - especially given that key serial numbers are randomly
allocated, thus leaving a lot of empty space in the tree.
So what I have is an associative array that internally is a radix-tree
with 16 pointers per node where the index key is constructed from the key
type pointer and the key description. This means that an exact lookup by
type+description is very fast as this tells us how to navigate directly to
the target key.
I made the data structure general in lib/assoc_array.c as far as it is
concerned, its index key is just a sequence of bits that leads to a
pointer. It's possible that someone else will be able to make use of it
also. FS-Cache might, for example.
(2) Mark keys as 'trusted' and keyrings as 'trusted only'.
KEYS: verify a certificate is signed by a 'trusted' key
KEYS: Make the system 'trusted' keyring viewable by userspace
KEYS: Add a 'trusted' flag and a 'trusted only' flag
KEYS: Separate the kernel signature checking keyring from module signing
These patches allow keys carrying asymmetric public keys to be marked as
being 'trusted' and allow keyrings to be marked as only permitting the
addition or linkage of trusted keys.
Keys loaded from hardware during kernel boot or compiled into the kernel
during build are marked as being trusted automatically. New keys can be
loaded at runtime with add_key(). They are checked against the system
keyring contents and if their signatures can be validated with keys that
are already marked trusted, then they are marked trusted also and can
thus be added into the master keyring.
Patches from Mimi Zohar make this usable with the IMA keyrings also.
(3) Remove the date checks on the key used to validate a module signature.
X.509: Remove certificate date checks
It's not reasonable to reject a signature just because the key that it was
generated with is no longer valid datewise - especially if the kernel
hasn't yet managed to set the system clock when the first module is
loaded - so just remove those checks.
(4) Make it simpler to deal with additional X.509 being loaded into the kernel.
KEYS: Load *.x509 files into kernel keyring
KEYS: Have make canonicalise the paths of the X.509 certs better to deduplicate
The builder of the kernel now just places files with the extension ".x509"
into the kernel source or build trees and they're concatenated by the
kernel build and stuffed into the appropriate section.
(5) Add support for userspace kerberos to use keyrings.
KEYS: Add per-user_namespace registers for persistent per-UID kerberos caches
KEYS: Implement a big key type that can save to tmpfs
Fedora went to, by default, storing kerberos tickets and tokens in tmpfs.
We looked at storing it in keyrings instead as that confers certain
advantages such as tickets being automatically deleted after a certain
amount of time and the ability for the kernel to get at these tokens more
easily.
To make this work, two things were needed:
(a) A way for the tickets to persist beyond the lifetime of all a user's
sessions so that cron-driven processes can still use them.
The problem is that a user's session keyrings are deleted when the
session that spawned them logs out and the user's user keyring is
deleted when the UID is deleted (typically when the last log out
happens), so neither of these places is suitable.
I've added a system keyring into which a 'persistent' keyring is
created for each UID on request. Each time a user requests their
persistent keyring, the expiry time on it is set anew. If the user
doesn't ask for it for, say, three days, the keyring is automatically
expired and garbage collected using the existing gc. All the kerberos
tokens it held are then also gc'd.
(b) A key type that can hold really big tickets (up to 1MB in size).
The problem is that Active Directory can return huge tickets with lots
of auxiliary data attached. We don't, however, want to eat up huge
tracts of unswappable kernel space for this, so if the ticket is
greater than a certain size, we create a swappable shmem file and dump
the contents in there and just live with the fact we then have an
inode and a dentry overhead. If the ticket is smaller than that, we
slap it in a kmalloc()'d buffer"
* 'for-linus2' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security: (121 commits)
KEYS: Fix keyring content gc scanner
KEYS: Fix error handling in big_key instantiation
KEYS: Fix UID check in keyctl_get_persistent()
KEYS: The RSA public key algorithm needs to select MPILIB
ima: define '_ima' as a builtin 'trusted' keyring
ima: extend the measurement list to include the file signature
kernel/system_certificate.S: use real contents instead of macro GLOBAL()
KEYS: fix error return code in big_key_instantiate()
KEYS: Fix keyring quota misaccounting on key replacement and unlink
KEYS: Fix a race between negating a key and reading the error set
KEYS: Make BIG_KEYS boolean
apparmor: remove the "task" arg from may_change_ptraced_domain()
apparmor: remove parent task info from audit logging
apparmor: remove tsk field from the apparmor_audit_struct
apparmor: fix capability to not use the current task, during reporting
Smack: Ptrace access check mode
ima: provide hash algo info in the xattr
ima: enable support for larger default filedata hash algorithms
ima: define kernel parameter 'ima_template=' to change configured default
ima: add Kconfig default measurement list template
...
Pull audit updates from Eric Paris:
"Nothing amazing. Formatting, small bug fixes, couple of fixes where
we didn't get records due to some old VFS changes, and a change to how
we collect execve info..."
Fixed conflict in fs/exec.c as per Eric and linux-next.
* git://git.infradead.org/users/eparis/audit: (28 commits)
audit: fix type of sessionid in audit_set_loginuid()
audit: call audit_bprm() only once to add AUDIT_EXECVE information
audit: move audit_aux_data_execve contents into audit_context union
audit: remove unused envc member of audit_aux_data_execve
audit: Kill the unused struct audit_aux_data_capset
audit: do not reject all AUDIT_INODE filter types
audit: suppress stock memalloc failure warnings since already managed
audit: log the audit_names record type
audit: add child record before the create to handle case where create fails
audit: use given values in tty_audit enable api
audit: use nlmsg_len() to get message payload length
audit: use memset instead of trying to initialize field by field
audit: fix info leak in AUDIT_GET requests
audit: update AUDIT_INODE filter rule to comparator function
audit: audit feature to set loginuid immutable
audit: audit feature to only allow unsetting the loginuid
audit: allow unsetting the loginuid (with priv)
audit: remove CONFIG_AUDIT_LOGINUID_IMMUTABLE
audit: loginuid functions coding style
selinux: apply selinux checks on new audit message types
...
This reverts commit ea1e7ed337.
Al points out that while the commit *does* actually create a separate
slab for the page->ptl allocation, that slab is never actually used, and
the code continues to use kmalloc/kfree.
Damien Wyart points out that the original patch did have the conversion
to use kmem_cache_alloc/free, so it got lost somewhere on its way to me.
Revert the half-arsed attempt that didn't do anything. If we really do
want the special slab (remember: this is all relevant just for debug
builds, so it's not necessarily all that critical) we might as well redo
the patch fully.
Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Kirill A Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This reverts commit 69f0554ec2.
This patch breaks randconfig on at least the x86-64 architecture, and
most likely on others. There is work underway to support uncompressed
kernels in a generic way, but it looks like it will amount to
rewriting the support from scratch; see the LKML thread in the Link:
for info.
Therefore, revert this change and wait for the fix.
Reported-by: Pavel Roskin <proski@gnu.org>
Cc: Christian Ruppert <christian.ruppert@abilis.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: http://lkml.kernel.org/r/20131113113418.167b8ffd@IRBT4585
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull trivial tree updates from Jiri Kosina:
"Usual earth-shaking, news-breaking, rocket science pile from
trivial.git"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (23 commits)
doc: usb: Fix typo in Documentation/usb/gadget_configs.txt
doc: add missing files to timers/00-INDEX
timekeeping: Fix some trivial typos in comments
mm: Fix some trivial typos in comments
irq: Fix some trivial typos in comments
NUMA: fix typos in Kconfig help text
mm: update 00-INDEX
doc: Documentation/DMA-attributes.txt fix typo
DRM: comment: `halve' -> `half'
Docs: Kconfig: `devlopers' -> `developers'
doc: typo on word accounting in kprobes.c in mutliple architectures
treewide: fix "usefull" typo
treewide: fix "distingush" typo
mm/Kconfig: Grammar s/an/a/
kexec: Typo s/the/then/
Documentation/kvm: Update cpuid documentation for steal time and pv eoi
treewide: Fix common typo in "identify"
__page_to_pfn: Fix typo in comment
Correct some typos for word frequency
clk: fixed-factor: Fix a trivial typo
...
If DEBUG_SPINLOCK and DEBUG_LOCK_ALLOC are enabled spinlock_t on x86_64
is 72 bytes. For page->ptl they will be allocated from kmalloc-96 slab,
so we loose 24 on each. An average system can easily allocate few tens
thousands of page->ptl and overhead is significant.
Let's create a separate slab for page->ptl allocation to solve this.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull networking updates from David Miller:
1) The addition of nftables. No longer will we need protocol aware
firewall filtering modules, it can all live in userspace.
At the core of nftables is a, for lack of a better term, virtual
machine that executes byte codes to inspect packet or metadata
(arriving interface index, etc.) and make verdict decisions.
Besides support for loading packet contents and comparing them, the
interpreter supports lookups in various datastructures as
fundamental operations. For example sets are supports, and
therefore one could create a set of whitelist IP address entries
which have ACCEPT verdicts attached to them, and use the appropriate
byte codes to do such lookups.
Since the interpreted code is composed in userspace, userspace can
do things like optimize things before giving it to the kernel.
Another major improvement is the capability of atomically updating
portions of the ruleset. In the existing netfilter implementation,
one has to update the entire rule set in order to make a change and
this is very expensive.
Userspace tools exist to create nftables rules using existing
netfilter rule sets, but both kernel implementations will need to
co-exist for quite some time as we transition from the old to the
new stuff.
Kudos to Patrick McHardy, Pablo Neira Ayuso, and others who have
worked so hard on this.
2) Daniel Borkmann and Hannes Frederic Sowa made several improvements
to our pseudo-random number generator, mostly used for things like
UDP port randomization and netfitler, amongst other things.
In particular the taus88 generater is updated to taus113, and test
cases are added.
3) Support 64-bit rates in HTB and TBF schedulers, from Eric Dumazet
and Yang Yingliang.
4) Add support for new 577xx tigon3 chips to tg3 driver, from Nithin
Sujir.
5) Fix two fatal flaws in TCP dynamic right sizing, from Eric Dumazet,
Neal Cardwell, and Yuchung Cheng.
6) Allow IP_TOS and IP_TTL to be specified in sendmsg() ancillary
control message data, much like other socket option attributes.
From Francesco Fusco.
7) Allow applications to specify a cap on the rate computed
automatically by the kernel for pacing flows, via a new
SO_MAX_PACING_RATE socket option. From Eric Dumazet.
8) Make the initial autotuned send buffer sizing in TCP more closely
reflect actual needs, from Eric Dumazet.
9) Currently early socket demux only happens for TCP sockets, but we
can do it for connected UDP sockets too. Implementation from Shawn
Bohrer.
10) Refactor inet socket demux with the goal of improving hash demux
performance for listening sockets. With the main goals being able
to use RCU lookups on even request sockets, and eliminating the
listening lock contention. From Eric Dumazet.
11) The bonding layer has many demuxes in it's fast path, and an RCU
conversion was started back in 3.11, several changes here extend the
RCU usage to even more locations. From Ding Tianhong and Wang
Yufen, based upon suggestions by Nikolay Aleksandrov and Veaceslav
Falico.
12) Allow stackability of segmentation offloads to, in particular, allow
segmentation offloading over tunnels. From Eric Dumazet.
13) Significantly improve the handling of secret keys we input into the
various hash functions in the inet hashtables, TCP fast open, as
well as syncookies. From Hannes Frederic Sowa. The key fundamental
operation is "net_get_random_once()" which uses static keys.
Hannes even extended this to ipv4/ipv6 fragmentation handling and
our generic flow dissector.
14) The generic driver layer takes care now to set the driver data to
NULL on device removal, so it's no longer necessary for drivers to
explicitly set it to NULL any more. Many drivers have been cleaned
up in this way, from Jingoo Han.
15) Add a BPF based packet scheduler classifier, from Daniel Borkmann.
16) Improve CRC32 interfaces and generic SKB checksum iterators so that
SCTP's checksumming can more cleanly be handled. Also from Daniel
Borkmann.
17) Add a new PMTU discovery mode, IP_PMTUDISC_INTERFACE, which forces
using the interface MTU value. This helps avoid PMTU attacks,
particularly on DNS servers. From Hannes Frederic Sowa.
18) Use generic XPS for transmit queue steering rather than internal
(re-)implementation in virtio-net. From Jason Wang.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1622 commits)
random32: add test cases for taus113 implementation
random32: upgrade taus88 generator to taus113 from errata paper
random32: move rnd_state to linux/random.h
random32: add prandom_reseed_late() and call when nonblocking pool becomes initialized
random32: add periodic reseeding
random32: fix off-by-one in seeding requirement
PHY: Add RTL8201CP phy_driver to realtek
xtsonic: add missing platform_set_drvdata() in xtsonic_probe()
macmace: add missing platform_set_drvdata() in mace_probe()
ethernet/arc/arc_emac: add missing platform_set_drvdata() in arc_emac_probe()
ipv6: protect for_each_sk_fl_rcu in mem_check with rcu_read_lock_bh
vlan: Implement vlan_dev_get_egress_qos_mask as an inline.
ixgbe: add warning when max_vfs is out of range.
igb: Update link modes display in ethtool
netfilter: push reasm skb through instead of original frag skbs
ip6_output: fragment outgoing reassembled skb properly
MAINTAINERS: mv643xx_eth: take over maintainership from Lennart
net_sched: tbf: support of 64bit rates
ixgbe: deleting dfwd stations out of order can cause null ptr deref
ixgbe: fix build err, num_rx_queues is only available with CONFIG_RPS
...
Make menuconfig allows one to choose compression format of an initial
ramdisk image. But this choice does not result in duly compressed ramdisk
image. Because - $ make install - does not pass on the selected
compression choice to the dracut(8) tool, which creates the initramfs
file. dracut(8) generates the image with the default compression, ie.
gzip(1).
This patch exports the selected compression option to a sub-shell
environment, so that it could be used by dracut(8) tool to generate
appropriately compressed initramfs images.
There isn't a straightforward way to pass on options to dracut(8) via
positional parameters. Because it is indirectly invoked at the end of a $
make install sequence.
# make install
-> arch/$arch/boot/Makefile
-> arch/$arch/boot/install.sh
-> /sbing/installkernel ...
-> /sbin/new-kernel-pkg ...
-> /sbin/dracut ...
Signed-off-by: P J P <ppandit@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some ARC users say they can boot faster with without kernel compression.
This probably depends on things like the FLASH chip they use etc.
Until now, kernel compression can only be disabled by removing "select
HAVE_<compression>" lines from the architecture Kconfig. So add the
Kconfig logic to permit disabling of kernel compression.
Signed-off-by: Christian Ruppert <christian.ruppert@abilis.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch proposes to make init failures more explicit.
Before this, the "No init found" message didn't help much. It could
sometimes be misleading and actually mean "No *working* init found".
This message could hide many different issues:
- no init program candidates found at all
- some init program candidates exist but can't be executed (missing
execute permissions, failed to load shared libraries, executable
compiled for an unknown architecture...)
This patch notifies the kernel user when a candidate init program is found
but can't be executed. In each failure situation, the error code is
displayed, to quickly find the root cause. "No init found" is also
replaced by "No working init found", which is more correct.
This will help embedded Linux developers (especially the newcomers),
regularly making and debugging new root filesystems.
Credits to Geert Uytterhoeven and Janne Karhunen for their improvement
suggestions.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Tested-by: Janne Karhunen <Janne.Karhunen@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make menuconfig allows one to choose compression format of an initial
ramdisk image. But this choice does not result in duly compressed initial
ramdisk image. Because - $ make install - does not pass on the selected
compression choice to the dracut(8) tool, which creates the initramfs
file. dracut(8) generates the image with the default compression, ie.
gzip(1).
If a user chose any other compression instead of gzip(1), it leads to a
crash due to NULL pointer dereference in crd_load(), caused by a NULL
function pointer returned by the 'decompress_method()' routine. Because
the initramfs image is gzip(1) compressed, whereas the kernel knows only
to decompress the chosen format and not gzip(1).
This patch replaces the crash by an explicit panic() call with an
appropriate error message. This shall prevent the kernel from
eventually panicking in: init/do_mounts.c: mount_block_root() with
-> panic("VFS: Unable to mount root fs on %s", b);
[akpm@linux-foundation.org: mention that the problem is with the ramdisk, don't print known-to-be-NULL value]
Signed-off-by: P J P <prasad@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The name_to_dev_t function has a comment block which lists the supported
syntaxes for the device name. Add a bullet for the <major>:<minor>
syntax, which is already supported in the code
Signed-off-by: Sebastian Capella <sebastian.capella@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull timer changes from Ingo Molnar:
"Main changes in this cycle were:
- Updated full dynticks support.
- Event stream support for architected (ARM) timers.
- ARM clocksource driver updates.
- Move arm64 to using the generic sched_clock framework & resulting
cleanup in the generic sched_clock code.
- Misc fixes and cleanups"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (50 commits)
x86/time: Honor ACPI FADT flag indicating absence of a CMOS RTC
clocksource: sun4i: remove IRQF_DISABLED
clocksource: sun4i: Report the minimum tick that we can program
clocksource: sun4i: Select CLKSRC_MMIO
clocksource: Provide timekeeping for efm32 SoCs
clocksource: em_sti: convert to clk_prepare/unprepare
time: Fix signedness bug in sysfs_get_uname() and its callers
timekeeping: Fix some trivial typos in comments
alarmtimer: return EINVAL instead of ENOTSUPP if rtcdev doesn't exist
clocksource: arch_timer: Do not register arch_sys_counter twice
timer stats: Add a 'Collection: active/inactive' line to timer usage statistics
sched_clock: Remove sched_clock_func() hook
arch_timer: Move to generic sched_clock framework
clocksource: tcb_clksrc: Remove IRQF_DISABLED
clocksource: tcb_clksrc: Improve driver robustness
clocksource: tcb_clksrc: Replace clk_enable/disable with clk_prepare_enable/disable_unprepare
clocksource: arm_arch_timer: Use clocksource for suspend timekeeping
clocksource: dw_apb_timer_of: Mark a few more functions as __init
clocksource: Put nodes passed to CLOCKSOURCE_OF_DECLARE callbacks centrally
arm: zynq: Enable arm_global_timer
...
Pull scheduler changes from Ingo Molnar:
"The main changes in this cycle are:
- (much) improved CONFIG_NUMA_BALANCING support from Mel Gorman, Rik
van Riel, Peter Zijlstra et al. Yay!
- optimize preemption counter handling: merge the NEED_RESCHED flag
into the preempt_count variable, by Peter Zijlstra.
- wait.h fixes and code reorganization from Peter Zijlstra
- cfs_bandwidth fixes from Ben Segall
- SMP load-balancer cleanups from Peter Zijstra
- idle balancer improvements from Jason Low
- other fixes and cleanups"
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (129 commits)
ftrace, sched: Add TRACE_FLAG_PREEMPT_RESCHED
stop_machine: Fix race between stop_two_cpus() and stop_cpus()
sched: Remove unnecessary iteration over sched domains to update nr_busy_cpus
sched: Fix asymmetric scheduling for POWER7
sched: Move completion code from core.c to completion.c
sched: Move wait code from core.c to wait.c
sched: Move wait.c into kernel/sched/
sched/wait: Fix __wait_event_interruptible_lock_irq_timeout()
sched: Avoid throttle_cfs_rq() racing with period_timer stopping
sched: Guarantee new group-entities always have weight
sched: Fix hrtimer_cancel()/rq->lock deadlock
sched: Fix cfs_bandwidth misuse of hrtimer_expires_remaining
sched: Fix race on toggling cfs_bandwidth_used
sched: Remove extra put_online_cpus() inside sched_setaffinity()
sched/rt: Fix task_tick_rt() comment
sched/wait: Fix build breakage
sched/wait: Introduce prepare_to_wait_event()
sched/wait: Add ___wait_cond_timeout() to wait_event*_timeout() too
sched: Remove get_online_cpus() usage
sched: Fix race in migrate_swap_stop()
...
After trying to use this feature in Fedora we found the hard coding
policy like this into the kernel was a bad idea. Surprise surprise.
We ran into these problems because it was impossible to launch a
container as a logged in user and run a login daemon inside that container.
This reverts back to the old behavior before this option was added. The
option will be re-added in a userspace selectable manor such that
userspace can choose when it is and when it is not appropriate.
Signed-off-by: Eric Paris <eparis@redhat.com>
Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: Eric Paris <eparis@redhat.com>
Before commit 026cee0086
("params: <level>_initcall-like kernel parameters") the __setup
parameter parsing code could modify parameter in the
static_command_line buffer and such modifications were kept. After
that commit such modifications are destroyed during per-initcall level
parameter parsing because the same static_command_line buffer is used
and only parameters for appropriate initcall level are parsed.
That change broke at least parsing "ubd" parameter in the ubd driver
when the COW file is used.
Now the separate buffer is used for per-initcall parameter parsing.
Signed-off-by: Krzysztof Mazur <krzysiek@podlesie.net>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Conflicts:
drivers/net/usb/qmi_wwan.c
include/net/dst.h
Trivial merge conflicts, both were overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Usage of the static key primitives to toggle a branch must not be used
before jump_label_init() is called from init/main.c. jump_label_init
reorganizes and wires up the jump_entries so usage before that could
have unforeseen consequences.
Following primitives are now checked for correct use:
* static_key_slow_inc
* static_key_slow_dec
* static_key_slow_dec_deferred
* jump_label_rate_limit
The x86 architecture already checks this by testing if the default_nop
was already replaced with an optimal nop or with a branch instruction. It
will panic then. Other architectures don't check for this.
Because we need to relax this check for the x86 arch to allow code to
transition from default_nop to the enabled state and other architectures
did not check for this at all this patch introduces checking on the
static_key primitives in a non-arch dependent manner.
All checked functions are considered slow-path so the additional check
does no harm to performance.
The warnings are best observed with earlyprintk.
Based on a patch from Andi Kleen.
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Andi Kleen <andi@firstfloor.org>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
non-x86 platforms, in particular MIPS and ARM.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=qnTe
-----END PGP SIGNATURE-----
Merge tag 'random_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random
Pull /dev/random changes from Ted Ts'o:
"These patches are designed to enable improvements to /dev/random for
non-x86 platforms, in particular MIPS and ARM"
* tag 'random_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random:
random: allow architectures to optionally define random_get_entropy()
random: run random_int_secret_init() run after all late_initcalls
The CONFIG_64BIT requirement on vtime can finally be removed
since we now depend on HAVE_VIRT_CPU_ACCOUNTING_GEN which
already takes care of the arch ability to handle nsecs based
cputime_t safely.
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Arm Linux <linux-arm-kernel@lists.infradead.org>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
With VIRT_CPU_ACCOUNTING_GEN, cputime_t becomes 64-bit. In order
to use that feature, arch code should be audited to ensure there are no
races in concurrent read/write of cputime_t. For example,
reading/writing 64-bit cputime_t on some 32-bit arches may require
multiple accesses for low and high value parts, so proper locking
is needed to protect against concurrent accesses.
Therefore, add CONFIG_HAVE_VIRT_CPU_ACCOUNTING_GEN which arches can
enable after they've been audited for potential races.
This option is automatically enabled on 64-bit platforms.
Feature requested by Frederic Weisbecker.
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Arm Linux <linux-arm-kernel@lists.infradead.org>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Separate the kernel signature checking keyring from module signing so that it
can be used by code other than the module-signing code.
Signed-off-by: David Howells <dhowells@redhat.com>
Replace the single preempt_count() 'function' that's an lvalue with
two proper functions:
preempt_count() - returns the preempt_count value as rvalue
preempt_count_set() - Allows setting the preempt-count value
Also provide preempt_count_ptr() as a convenience wrapper to implement
all modifying operations.
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/n/tip-orxrbycjozopqfhb4dxdkdvb@git.kernel.org
[ Fixed build failure. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The some platforms (e.g., ARM) initializes their clocks as
late_initcalls for some unknown reason. So make sure
random_int_secret_init() is run after all of the late_initcalls are
run.
Cc: stable@vger.kernel.org
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Pull SLAB update from Pekka Enberg:
"Nothing terribly exciting here apart from Christoph's kmalloc
unification patches that brings sl[aou]b implementations closer to
each other"
* 'slab/next' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/linux:
slab: Use correct GFP_DMA constant
slub: remove verify_mem_not_deleted()
mm/sl[aou]b: Move kmallocXXX functions to common code
mm, slab_common: add 'unlikely' to size check of kmalloc_slab()
mm/slub.c: beautify code for removing redundancy 'break' statement.
slub: Remove unnecessary page NULL check
slub: don't use cpu partial pages on UP
mm/slub: beautify code for 80 column limitation and tab alignment
mm/slub: remove 'per_cpu' which is useless variable
Command line option rootfstype=ramfs to obtain old initramfs behavior, and
use ramfs instead of tmpfs for stub when root= defined (for cosmetic
reasons).
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Rob Landley <rob@landley.net>
Cc: Jeff Layton <jlayton@redhat.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Jim Cromie <jim.cromie@gmail.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Conditionally call the appropriate fs_init function and fill_super
functions. Add a use once guard to shmem_init() to simply succeed on a
second call.
(Note that IS_ENABLED() is a compile time constant so dead code
elimination removes unused function calls when CONFIG_TMPFS is disabled.)
Signed-off-by: Rob Landley <rob@landley.net>
Cc: Jeff Layton <jlayton@redhat.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Jim Cromie <jim.cromie@gmail.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When the rootfs code was a wrapper around ramfs, having them in the same
file made sense. Now that it can wrap another filesystem type, move it in
with the init code instead.
This also allows a subsequent patch to access rootfstype= command line
arg.
Signed-off-by: Rob Landley <rob@landley.net>
Cc: Jeff Layton <jlayton@redhat.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Jim Cromie <jim.cromie@gmail.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull kconfig updates from Michal Marek:
"This is the kconfig part of kbuild for v3.12-rc1:
- post-3.11 search code fixes and micro-optimizations
- CONFIG_MODULES is no longer a special case; this is needed to
eventually fix the bug that using KCONFIG_ALLCONFIG breaks
allmodconfig
- long long is used to store hex and int values
- make silentoldconfig no longer warns when a symbol changes from
tristate to bool (it's a job for make oldconfig)
- scripts/diffconfig updated to work with newer Pythons
- scripts/config does not rely on GNU sed extensions"
* 'kconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
kconfig: do not allow more than one symbol to have 'option modules'
kconfig: regenerate bison parser
kconfig: do not special-case 'MODULES' symbol
diffconfig: Update script to support python versions 2.5 through 3.3
diffconfig: Gracefully exit if the default config files are not present
modules: do not depend on kconfig to set 'modules' option to symbol MODULES
kconfig: silence warning when parsing auto.conf when a symbol has changed type
scripts/config: use sed's POSIX interface
kconfig: switch to "long long" for sanity
kconfig: simplify symbol-search code
kconfig: don't allocate n+1 elements in temporary array
kconfig: minor style fixes in symbol-search code
kconfig/[mn]conf: shorten title in search-box
kconfig: avoid multiple calls to strlen
Documentation/kconfig: more concise and straightforward search explanation
For 3.12-rc1 there are a number of bugfixes in addition to work to ease usage
of shared code between libxfs and the kernel, the rest of the work to enable
project and group quotas to be used simultaneously, performance optimisations
in the log and the CIL, directory entry file type support, fixes for log space
reservations, some spelling/grammar cleanups, and the addition of user
namespace support.
- introduce readahead to log recovery
- add directory entry file type support
- fix a number of spelling errors in comments
- introduce new Q_XGETQSTATV quotactl for project quotas
- add USER_NS support
- log space reservation rework
- CIL optimisations
- kernel/userspace libxfs rework
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=V4s4
-----END PGP SIGNATURE-----
Merge tag 'xfs-for-linus-v3.12-rc1' of git://oss.sgi.com/xfs/xfs
Pull xfs updates from Ben Myers:
"For 3.12-rc1 there are a number of bugfixes in addition to work to
ease usage of shared code between libxfs and the kernel, the rest of
the work to enable project and group quotas to be used simultaneously,
performance optimisations in the log and the CIL, directory entry file
type support, fixes for log space reservations, some spelling/grammar
cleanups, and the addition of user namespace support.
- introduce readahead to log recovery
- add directory entry file type support
- fix a number of spelling errors in comments
- introduce new Q_XGETQSTATV quotactl for project quotas
- add USER_NS support
- log space reservation rework
- CIL optimisations
- kernel/userspace libxfs rework"
* tag 'xfs-for-linus-v3.12-rc1' of git://oss.sgi.com/xfs/xfs: (112 commits)
xfs: XFS_MOUNT_QUOTA_ALL needed by userspace
xfs: dtype changed xfs_dir2_sfe_put_ino to xfs_dir3_sfe_put_ino
Fix wrong flag ASSERT in xfs_attr_shortform_getvalue
xfs: finish removing IOP_* macros.
xfs: inode log reservations are too small
xfs: check correct status variable for xfs_inobt_get_rec() call
xfs: inode buffers may not be valid during recovery readahead
xfs: check LSN ordering for v5 superblocks during recovery
xfs: btree block LSN escaping to disk uninitialised
XFS: Assertion failed: first <= last && last < BBTOB(bp->b_length), file: fs/xfs/xfs_trans_buf.c, line: 568
xfs: fix bad dquot buffer size in log recovery readahead
xfs: don't account buffer cancellation during log recovery readahead
xfs: check for underflow in xfs_iformat_fork()
xfs: xfs_dir3_sfe_put_ino can be static
xfs: introduce object readahead to log recovery
xfs: Simplify xfs_ail_min() with list_first_entry_or_null()
xfs: Register hotcpu notifier after initialization
xfs: add xfs sb v4 support for dirent filetype field
xfs: Add write support for dirent filetype field
xfs: Add read-only support for dirent filetype field
...
Pull timers/nohz changes from Ingo Molnar:
"It mostly contains fixes and full dynticks off-case optimizations, by
Frederic Weisbecker"
* 'timers-nohz-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (24 commits)
nohz: Include local CPU in full dynticks global kick
nohz: Optimize full dynticks's sched hooks with static keys
nohz: Optimize full dynticks state checks with static keys
nohz: Rename a few state variables
vtime: Always debug check snapshot source _before_ updating it
vtime: Always scale generic vtime accounting results
vtime: Optimize full dynticks accounting off case with static keys
vtime: Describe overriden functions in dedicated arch headers
m68k: hardirq_count() only need preempt_mask.h
hardirq: Split preempt count mask definitions
context_tracking: Split low level state headers
vtime: Fix racy cputime delta update
vtime: Remove a few unneeded generic vtime state checks
context_tracking: User/kernel broundary cross trace events
context_tracking: Optimize context switch off case with static keys
context_tracking: Optimize guest APIs off case with static key
context_tracking: Optimize main APIs off case with static key
context_tracking: Ground setup for static key use
context_tracking: Remove full dynticks' hacky dependency on wide context tracking
nohz: Only enable context tracking on full dynticks CPUs
...
Pull RCU updates from Paul E. McKenney:
"
* Update RCU documentation. These were posted to LKML at
https://lkml.org/lkml/2013/8/19/611.
* Miscellaneous fixes. These were posted to LKML at
https://lkml.org/lkml/2013/8/19/619.
* Full-system idle detection. This is for use by Frederic
Weisbecker's adaptive-ticks mechanism. Its purpose is
to allow the timekeeping CPU to shut off its tick when
all other CPUs are idle. These were posted to LKML at
https://lkml.org/lkml/2013/8/19/648.
* Improve rcutorture test coverage. These were posted to LKML at
https://lkml.org/lkml/2013/8/19/675.
"
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The swapaccount kernel parameter without any values has been removed by
commit a2c8990aed ("memsw: remove noswapaccount kernel parameter") but
it seems that we didn't get rid of all the left overs.
Make sure that menuconfig help text and kernel-parameters.txt are clear
about value for the paramter and remove the stalled comment which is not
very much useful on its own.
Signed-off-by: Michal Hocko <mhocko@suse.cz>
Reported-by: Gergely Risko <gergely@risko.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
TREE_RCU and TREE_PREEMPT_RCU both cause kernel/rcutree.c to be built,
but only TREE_RCU selects IRQ_WORK, which can result in an undefined
reference to irq_work_queue for some (random) configs:
kernel/built-in.o In function `rcu_start_gp_advanced':
kernel/rcutree.c:1564: undefined reference to `irq_work_queue'
Select IRQ_WORK from TREE_PREEMPT_RCU too to fix this.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Dipankar Sarma <dipankar@in.ibm.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Currently, the MODULES symbol is special-cased in different places in the
kconfig language. For example, if no symbol is defined to enable tristates,
then kconfig looks up for a symbol named 'MODULES', and forces the 'modules'
option onto that symbol.
This causes problems as such:
- since MODULES is special-cased, reading the configuration with
KCONFIG_ALLCONFIG set will forcibly set MODULES to be 'valid' (ie.
it has a valid value), when no such value was previously set. So
MODULES defaults to 'n' unless it is present in KCONFIG_ALLCONFIG
- other third-party projects may decide that 'MODULES' plays a different
role for them
This has been exposed by cset #cfa98f2e:
kconfig: do not override symbols already set
and reported by Stephen in:
http://marc.info/?l=linux-next&m=137592137915234&w=2
As suggested by Sam, we explicitly define the MODULES symbol to be the
tristate-enabler. This will allow us to drop special-casing of MODULES
in the kconfig language, later.
(Note: this patch is not a fix to Stephen's issue, just a first step).
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: yann.morin.1998@free.fr
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Michal Marek <mmarek@suse.cz>
Cc: Kevin Hilman <khilman@linaro.org>
Cc: sedat.dilek@gmail.com
Cc: Theodore Ts'o <tytso@mit.edu>
Prepare for using a static key in the context tracking subsystem.
This will help optimizing the off case on its many users:
* user_enter, user_exit, exception_enter, exception_exit, guest_enter,
guest_exit, vtime_*()
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Li Zhong <zhong@linux.vnet.ibm.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Kevin Hilman <khilman@linaro.org>
cpu partial pages are used to avoid contention which does not exist in
the UP case. So let SLUB_CPU_PARTIAL depend on SMP.
Acked-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Pekka Enberg <penberg@kernel.org>
Now that the full dynticks subsystem only enables the context tracking
on full dynticks CPUs, lets remove the dependency on CONTEXT_TRACKING_FORCE
This dependency was a hack to enable the context tracking widely for the
full dynticks susbsystem until the latter becomes able to enable it in a
more CPU-finegrained fashion.
Now CONTEXT_TRACKING_FORCE only stands for testing on archs that
work on support for the context tracking while full dynticks can't be
used yet due to unmet dependencies. It simulates a system where all CPUs
are full dynticks so that RCU user extended quiescent states and dynticks
cputime accounting can be tested on the given arch.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Li Zhong <zhong@linux.vnet.ibm.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Kevin Hilman <khilman@linaro.org>
The __cpuinit type of throwaway sections might have made sense
some time ago when RAM was more constrained, but now the savings
do not offset the cost and complications. For example, the fix in
commit 5e427ec2d0 ("x86: Fix bit corruption at CPU resume time")
is a good example of the nasty type of bugs that can be created
with improper use of the various __init prefixes.
After a discussion on LKML[1] it was decided that cpuinit should go
the way of devinit and be phased out. Once all the users are gone,
we can then finally remove the macros themselves from linux/init.h.
This removes all the uses of the __cpuinit macros from C files in
the core kernel directories (kernel, init, lib, mm, and include)
that don't really have a specific maintainer.
[1] https://lkml.org/lkml/2013/5/20/589
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Pull slab update from Pekka Enberg:
"Highlights:
- Fix for boot-time problems on some architectures due to
init_lock_keys() not respecting kmalloc_caches boundaries
(Christoph Lameter)
- CONFIG_SLUB_CPU_PARTIAL requested by RT folks (Joonsoo Kim)
- Fix for excessive slab freelist draining (Wanpeng Li)
- SLUB and SLOB cleanups and fixes (various people)"
I ended up editing the branch, and this avoids two commits at the end
that were immediately reverted, and I instead just applied the oneliner
fix in between myself.
* 'slab/for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/linux
slub: Check for page NULL before doing the node_match check
mm/slab: Give s_next and s_stop slab-specific names
slob: Check for NULL pointer before calling ctor()
slub: Make cpu partial slab support configurable
slab: add kmalloc() to kernel API documentation
slab: fix init_lock_keys
slob: use DIV_ROUND_UP where possible
slub: do not put a slab to cpu partial list when cpu_partial is 0
mm/slub: Use node_nr_slabs and node_nr_objs in get_slabinfo
mm/slub: Drop unnecessary nr_partials
mm/slab: Fix /proc/slabinfo unwriteable for slab
mm/slab: Sharing s_next and s_stop between slab and slub
mm/slab: Fix drain freelist excessively
slob: Rework #ifdeffery in slab.h
mm, slab: moved kmem_cache_alloc_node comment to correct place
Add support for extracting LZ4-compressed kernel images, as well as
LZ4-compressed ramdisk images in the kernel boot process.
Signed-off-by: Kyungsik Lee <kyungsik.lee@lge.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Yann Collet <yann.collet.73@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
CPU partial support can introduce level of indeterminism that is not
wanted in certain context (like a realtime kernel). Make it
configurable.
This patch is based on Christoph Lameter's "slub: Make cpu partial slab
support configurable V2".
Acked-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Signed-off-by: Pekka Enberg <penberg@kernel.org>
Pull timer core updates from Thomas Gleixner:
"The timer changes contain:
- posix timer code consolidation and fixes for odd corner cases
- sched_clock implementation moved from ARM to core code to avoid
duplication by other architectures
- alarm timer updates
- clocksource and clockevents unregistration facilities
- clocksource/events support for new hardware
- precise nanoseconds RTC readout (Xen feature)
- generic support for Xen suspend/resume oddities
- the usual lot of fixes and cleanups all over the place
The parts which touch other areas (ARM/XEN) have been coordinated with
the relevant maintainers. Though this results in an handful of
trivial to solve merge conflicts, which we preferred over nasty cross
tree merge dependencies.
The patches which have been committed in the last few days are bug
fixes plus the posix timer lot. The latter was in akpms queue and
next for quite some time; they just got forgotten and Frederic
collected them last minute."
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (59 commits)
hrtimer: Remove unused variable
hrtimers: Move SMP function call to thread context
clocksource: Reselect clocksource when watchdog validated high-res capability
posix-cpu-timers: don't account cpu timer after stopped thread runtime accounting
posix_timers: fix racy timer delta caching on task exit
posix-timers: correctly get dying task time sample in posix_cpu_timer_schedule()
selftests: add basic posix timers selftests
posix_cpu_timers: consolidate expired timers check
posix_cpu_timers: consolidate timer list cleanups
posix_cpu_timer: consolidate expiry time type
tick: Sanitize broadcast control logic
tick: Prevent uncontrolled switch to oneshot mode
tick: Make oneshot broadcast robust vs. CPU offlining
x86: xen: Sync the CMOS RTC as well as the Xen wallclock
x86: xen: Sync the wallclock when the system time is set
timekeeping: Indicate that clock was set in the pvclock gtod notifier
timekeeping: Pass flags instead of multiple bools to timekeeping_update()
xen: Remove clock_was_set() call in the resume path
hrtimers: Support resuming with two or more CPUs online (but stopped)
timer: Fix jiffies wrap behavior of round_jiffies_common()
...
git://git.kernel.org/pub/scm/linux/kernel/git/frederic/linux-dynticks into timers/core
Frederic sayed: "Most of these patches have been hanging around for
several month now, in -mmotm for a significant chunk. They already
missed a few releases."
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
do_one_initcall() uses a 64 byte string buffer to save a message. This
buffer is declared static and is only used at boot up and when a module
is loaded. As 64 bytes is very small, and this function has very limited
scope, there's no reason to waste permanent memory with this string and
not just simply put it on the stack.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now there are only 2 members in struct page_cgroup. Update config MEMCG
description accordingly.
Signed-off-by: Sergey Dyasly <dserrg@gmail.com>
Acked-by: Michal Hocko <mhocko@suse.cz>
Acked-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull perf updates from Ingo Molnar:
"Kernel improvements:
- watchdog driver improvements by Li Zefan
- Power7 CPI stack events related improvements by Sukadev Bhattiprolu
- event multiplexing via hrtimers and other improvements by Stephane
Eranian
- kernel stack use optimization by Andrew Hunter
- AMD IOMMU uncore PMU support by Suravee Suthikulpanit
- NMI handling rate-limits by Dave Hansen
- various hw_breakpoint fixes by Oleg Nesterov
- hw_breakpoint overflow period sampling and related signal handling
fixes by Jiri Olsa
- Intel Haswell PMU support by Andi Kleen
Tooling improvements:
- Reset SIGTERM handler in workload child process, fix from David
Ahern.
- Makefile reorganization, prep work for Kconfig patches, from Jiri
Olsa.
- Add automated make test suite, from Jiri Olsa.
- Add --percent-limit option to 'top' and 'report', from Namhyung
Kim.
- Sorting improvements, from Namhyung Kim.
- Expand definition of sysfs format attribute, from Michael Ellerman.
Tooling fixes:
- 'perf tests' fixes from Jiri Olsa.
- Make Power7 CPI stack events available in sysfs, from Sukadev
Bhattiprolu.
- Handle death by SIGTERM in 'perf record', fix from David Ahern.
- Fix printing of perf_event_paranoid message, from David Ahern.
- Handle realloc failures in 'perf kvm', from David Ahern.
- Fix divide by 0 in variance, from David Ahern.
- Save parent pid in thread struct, from David Ahern.
- Handle JITed code in shared memory, from Andi Kleen.
- Fixes for 'perf diff', from Jiri Olsa.
- Remove some unused struct members, from Jiri Olsa.
- Add missing liblk.a dependency for python/perf.so, fix from Jiri
Olsa.
- Respect CROSS_COMPILE in liblk.a, from Rabin Vincent.
- No need to do locking when adding hists in perf report, only 'top'
needs that, from Namhyung Kim.
- Fix alignment of symbol column in in the hists browser (top,
report) when -v is given, from NAmhyung Kim.
- Fix 'perf top' -E option behavior, from Namhyung Kim.
- Fix bug in isupper() and islower(), from Sukadev Bhattiprolu.
- Fix compile errors in bp_signal 'perf test', from Sukadev
Bhattiprolu.
... and more things"
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (102 commits)
perf/x86: Disable PEBS-LL in intel_pmu_pebs_disable()
perf/x86: Fix shared register mutual exclusion enforcement
perf/x86/intel: Support full width counting
x86: Add NMI duration tracepoints
perf: Drop sample rate when sampling is too slow
x86: Warn when NMI handlers take large amounts of time
hw_breakpoint: Introduce "struct bp_cpuinfo"
hw_breakpoint: Simplify *register_wide_hw_breakpoint()
hw_breakpoint: Introduce cpumask_of_bp()
hw_breakpoint: Simplify the "weight" usage in toggle_bp_slot() paths
hw_breakpoint: Simplify list/idx mess in toggle_bp_slot() paths
perf/x86/intel: Add mem-loads/stores support for Haswell
perf/x86/intel: Support Haswell/v4 LBR format
perf/x86/intel: Move NMI clearing to end of PMI handler
perf/x86/intel: Add Haswell PEBS support
perf/x86/intel: Add simple Haswell PMU support
perf/x86/intel: Add Haswell PEBS record support
perf/x86/intel: Fix sparse warning
perf/x86/amd: AMD IOMMU Performance Counter PERF uncore PMU implementation
perf/x86/amd: Add IOMMU Performance Counter resource management
...
Some drivers can be built on more platforms than they run on. This is
a burden for users and distributors who package a kernel. They have to
manually deselect some (for them useless) drivers when updating their
configs via oldconfig. And yet, sometimes it is even impossible to
disable the drivers without patching the kernel.
Introduce a new config option COMPILE_TEST and make all those drivers
to depend on the platform they run on, or on the COMPILE_TEST option.
Now, when users/distributors choose COMPILE_TEST=n they will not have
the drivers in their allmodconfig setups, but developers still can
compile-test them with COMPILE_TEST=y.
Now the drivers where we use this new option:
* PTP_1588_CLOCK_PCH: The PCH EG20T is only compatible with Intel Atom
processors so it should depend on x86.
* FB_GEODE: Geode is 32-bit only so only enable it for X86_32.
* USB_CHIPIDEA_IMX: The OF_DEVICE dependency will be met on powerpc
systems -- which do not actually support the hardware via that
method.
* INTEL_MID_PTI: It is specific to the Penwell type of Intel Atom
device.
[v2]
* remove EXPERT dependency
[gregkh - remove chipidea portion, as it's incorrect, and also doesn't
apply to my driver-core tree]
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Jeff Mahoney <jeffm@suse.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: linux-usb@vger.kernel.org
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: linux-geode@lists.infradead.org
Cc: linux-fbdev@vger.kernel.org
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: netdev@vger.kernel.org
Cc: Ben Hutchings <ben@decadent.org.uk>
Cc: "Keller, Jacob E" <jacob.e.keller@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Nothing about the sched_clock implementation in the ARM port is
specific to the architecture. Generalize the code so that other
architectures can use it by selecting GENERIC_SCHED_CLOCK.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
[jstultz: Merge minor collisions with other patches in my tree]
Signed-off-by: John Stultz <john.stultz@linaro.org>
TINY_PREEMPT_RCU adds significant code and complexity, but does not
offer commensurate benefits. People currently using TINY_PREEMPT_RCU
can get much better memory footprint with TINY_RCU, or, if they really
need preemptible RCU, they can use TREE_PREEMPT_RCU with a relatively
minor degradation in memory footprint. Please note that this move
has been widely publicized on LKML (https://lkml.org/lkml/2012/11/12/545)
and on LWN (http://lwn.net/Articles/541037/).
This commit therefore removes TINY_PREEMPT_RCU.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
[ paulmck: Updated to eliminate #else in rcutiny.h as suggested by Josh ]
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
The Kconfig help text for the RCU_NOCB_CPU_NONE, RCU_NOCB_CPU_ZERO,
and RCU_NOCB_CPU_ALL Kconfig options was unclear, so this commit
adds a bit more detail.
Reported-by: Dave Jones <davej@redhat.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
After a release or two, features are no longer experimental. Therefore,
this commit removes the "Experimental" tag from them.
Reported-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Ever since commit 45f035ab9b ("CONFIG_HOTPLUG should be always on"),
it has been basically impossible to build a kernel with CONFIG_HOTPLUG
turned off. Remove all the remaining references to it.
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Doug Thompson <dougthompson@xmission.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current scheme of using the timer tick was fine for per-thread
events. However, it was causing bias issues in system-wide mode
(including for uncore PMUs). Event groups would not get their fair
share of runtime on the PMU. With tickless kernels, if a core is idle
there is no timer tick, and thus no event rotation (multiplexing).
However, there are events (especially uncore events) which do count
even though cores are asleep.
This patch changes the timer source for multiplexing. It introduces a
per-PMU per-cpu hrtimer. The advantage is that even when a core goes
idle, it will come back to service the hrtimer, thus multiplexing on
system-wide events works much better.
The per-PMU implementation (suggested by PeterZ) enables adjusting the
multiplexing interval per PMU. The preferred interval is stashed into
the struct pmu. If not set, it will be forced to the default interval
value.
In order to minimize the impact of the hrtimer, it is turned on and
off on demand. When the PMU on a CPU is overcommited, the hrtimer is
activated. It is stopped when the PMU is not overcommitted.
In order for this to work properly, we had to change the order of
initialization in start_kernel() such that hrtimer_init() is run
before perf_event_init().
The default interval in milliseconds is set to a timer tick just like
with the old code. We will provide a sysctl to tune this in another
patch.
Signed-off-by: Stephane Eranian <eranian@google.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Link: http://lkml.kernel.org/r/1364991694-5876-2-git-send-email-eranian@google.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull 'full dynticks' support from Ingo Molnar:
"This tree from Frederic Weisbecker adds a new, (exciting! :-) core
kernel feature to the timer and scheduler subsystems: 'full dynticks',
or CONFIG_NO_HZ_FULL=y.
This feature extends the nohz variable-size timer tick feature from
idle to busy CPUs (running at most one task) as well, potentially
reducing the number of timer interrupts significantly.
This feature got motivated by real-time folks and the -rt tree, but
the general utility and motivation of full-dynticks runs wider than
that:
- HPC workloads get faster: CPUs running a single task should be able
to utilize a maximum amount of CPU power. A periodic timer tick at
HZ=1000 can cause a constant overhead of up to 1.0%. This feature
removes that overhead - and speeds up the system by 0.5%-1.0% on
typical distro configs even on modern systems.
- Real-time workload latency reduction: CPUs running critical tasks
should experience as little jitter as possible. The last remaining
source of kernel-related jitter was the periodic timer tick.
- A single task executing on a CPU is a pretty common situation,
especially with an increasing number of cores/CPUs, so this feature
helps desktop and mobile workloads as well.
The cost of the feature is mainly related to increased timer
reprogramming overhead when a CPU switches its tick period, and thus
slightly longer to-idle and from-idle latency.
Configuration-wise a third mode of operation is added to the existing
two NOHZ kconfig modes:
- CONFIG_HZ_PERIODIC: [formerly !CONFIG_NO_HZ], now explicitly named
as a config option. This is the traditional Linux periodic tick
design: there's a HZ tick going on all the time, regardless of
whether a CPU is idle or not.
- CONFIG_NO_HZ_IDLE: [formerly CONFIG_NO_HZ=y], this turns off the
periodic tick when a CPU enters idle mode.
- CONFIG_NO_HZ_FULL: this new mode, in addition to turning off the
tick when a CPU is idle, also slows the tick down to 1 Hz (one
timer interrupt per second) when only a single task is running on a
CPU.
The .config behavior is compatible: existing !CONFIG_NO_HZ and
CONFIG_NO_HZ=y settings get translated to the new values, without the
user having to configure anything. CONFIG_NO_HZ_FULL is turned off by
default.
This feature is based on a lot of infrastructure work that has been
steadily going upstream in the last 2-3 cycles: related RCU support
and non-periodic cputime support in particular is upstream already.
This tree adds the final pieces and activates the feature. The pull
request is marked RFC because:
- it's marked 64-bit only at the moment - the 32-bit support patch is
small but did not get ready in time.
- it has a number of fresh commits that came in after the merge
window. The overwhelming majority of commits are from before the
merge window, but still some aspects of the tree are fresh and so I
marked it RFC.
- it's a pretty wide-reaching feature with lots of effects - and
while the components have been in testing for some time, the full
combination is still not very widely used. That it's default-off
should reduce its regression abilities and obviously there are no
known regressions with CONFIG_NO_HZ_FULL=y enabled either.
- the feature is not completely idempotent: there is no 100%
equivalent replacement for a periodic scheduler/timer tick. In
particular there's ongoing work to map out and reduce its effects
on scheduler load-balancing and statistics. This should not impact
correctness though, there are no known regressions related to this
feature at this point.
- it's a pretty ambitious feature that with time will likely be
enabled by most Linux distros, and we'd like you to make input on
its design/implementation, if you dislike some aspect we missed.
Without flaming us to crisp! :-)
Future plans:
- there's ongoing work to reduce 1Hz to 0Hz, to essentially shut off
the periodic tick altogether when there's a single busy task on a
CPU. We'd first like 1 Hz to be exposed more widely before we go
for the 0 Hz target though.
- once we reach 0 Hz we can remove the periodic tick assumption from
nr_running>=2 as well, by essentially interrupting busy tasks only
as frequently as the sched_latency constraints require us to do -
once every 4-40 msecs, depending on nr_running.
I am personally leaning towards biting the bullet and doing this in
v3.10, like the -rt tree this effort has been going on for too long -
but the final word is up to you as usual.
More technical details can be found in Documentation/timers/NO_HZ.txt"
* 'timers-nohz-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (39 commits)
sched: Keep at least 1 tick per second for active dynticks tasks
rcu: Fix full dynticks' dependency on wide RCU nocb mode
nohz: Protect smp_processor_id() in tick_nohz_task_switch()
nohz_full: Add documentation.
cputime_nsecs: use math64.h for nsec resolution conversion helpers
nohz: Select VIRT_CPU_ACCOUNTING_GEN from full dynticks config
nohz: Reduce overhead under high-freq idling patterns
nohz: Remove full dynticks' superfluous dependency on RCU tree
nohz: Fix unavailable tick_stop tracepoint in dynticks idle
nohz: Add basic tracing
nohz: Select wide RCU nocb for full dynticks
nohz: Disable the tick when irq resume in full dynticks CPU
nohz: Re-evaluate the tick for the new task after a context switch
nohz: Prepare to stop the tick on irq exit
nohz: Implement full dynticks kick
nohz: Re-evaluate the tick from the scheduler IPI
sched: New helper to prevent from stopping the tick in full dynticks
sched: Kick full dynticks CPU that have more than one task enqueued.
perf: New helper to prevent full dynticks CPUs from stopping tick
perf: Kick full dynticks CPU if events rotation is needed
...
Commit 0637e02939
("nohz: Select wide RCU nocb for full dynticks") intended
to force CONFIG_RCU_NOCB_CPU_ALL=y when full dynticks is
enabled.
However this option is part of a choice menu and Kconfig's
"select" instruction has no effect on such targets.
Fix this by using reverse dependencies on the targets we
don't want instead.
Reviewed-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Hakan Akkan <hakanakkan@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Kevin Hilman <khilman@linaro.org>
Cc: Li Zhong <zhong@linux.vnet.ibm.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
The full dynticks tree needs the latest RCU and sched
upstream updates in order to fix some dependencies.
Merge a common upstream merge point that has these
updates.
Conflicts:
include/linux/perf_event.h
kernel/rcutree.h
kernel/rcutree_plugin.h
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Pull VFS updates from Al Viro,
Misc cleanups all over the place, mainly wrt /proc interfaces (switch
create_proc_entry to proc_create(), get rid of the deprecated
create_proc_read_entry() in favor of using proc_create_data() and
seq_file etc).
7kloc removed.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (204 commits)
don't bother with deferred freeing of fdtables
proc: Move non-public stuff from linux/proc_fs.h to fs/proc/internal.h
proc: Make the PROC_I() and PDE() macros internal to procfs
proc: Supply a function to remove a proc entry by PDE
take cgroup_open() and cpuset_open() to fs/proc/base.c
ppc: Clean up scanlog
ppc: Clean up rtas_flash driver somewhat
hostap: proc: Use remove_proc_subtree()
drm: proc: Use remove_proc_subtree()
drm: proc: Use minor->index to label things, not PDE->name
drm: Constify drm_proc_list[]
zoran: Don't print proc_dir_entry data in debug
reiserfs: Don't access the proc_dir_entry in r_open(), r_start() r_show()
proc: Supply an accessor for getting the data from a PDE's parent
airo: Use remove_proc_subtree()
rtl8192u: Don't need to save device proc dir PDE
rtl8187se: Use a dir under /proc/net/r8180/
proc: Add proc_mkdir_data()
proc: Move some bits from linux/proc_fs.h to linux/{of.h,signal.h,tty.h}
proc: Move PDE_NET() to fs/proc/proc_net.c
...
Split the proc namespace stuff out into linux/proc_ns.h.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: netdev@vger.kernel.org
cc: Serge E. Hallyn <serge.hallyn@ubuntu.com>
cc: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Commit f91eb62f71 ("init: scream bloody murder if interrupts are
enabled too early") added three new warnings. The first two seemed
reasonable, but the third included a warning when an initcall returned
non-zero. Although, the third WARN() does include an imbalanced preempt
disabled, or irqs disable, it shouldn't warn if it only had an initcall
that just returns non-zero.
In fact, according to Linus, it shouldn't print at all. As it only
prints with initcall_debug set, and that already shows enough
information to fix things.
Link: http://lkml.kernel.org/r/CA+55aFzaBC5SFi7=F2mfm+KWY5qTsBmOqgbbs8E+LUS8JK-sBg@mail.gmail.com
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Reported-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The kconfig language requires that dependent options all follow the
menuconfig symbol in order to be collapsed below it. Recently some hidden
options were added below the EXPERT menuconfig, but did not depend on
EXPERT (because hidden options can't). This broke the display. So
re-order all these options, and while we're here stick the PCI quirks
under the EXPERT menu (since it isn't sitting with any related options).
Before this commit, we get:
[*] Configure standard kernel features (expert users) --->
[ ] Sysctl syscall support
[*] Load all symbols for debugging/ksymoops
...
[ ] Embedded system
Now we get the older (and correct) behavior:
[*] Configure standard kernel features (expert users) --->
[ ] Embedded system
And if you go into the expert menu you get the expert options:
[ ] Sysctl syscall support
[*] Load all symbols for debugging/ksymoops
...
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Cc: zhangwei(Jovi) <jovi.zhangwei@huawei.com>
Cc: Michal Marek <mmarek@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
These are the only users of call_usermodehelper_fns(). This function
suffers from not being able to determine if the cleanup is called. Even
if in this places the cleanup pointer is NULL, convert them to use the
separate call_usermodehelper_setup() + call_usermodehelper_exec()
functions so we can remove the _fns variant.
Signed-off-by: Lucas De Marchi <lucas.demarchi@profusion.mobi>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: David Howells <dhowells@redhat.com>
Cc: James Morris <james.l.morris@oracle.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Tejun Heo <tj@kernel.org>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull core timer updates from Ingo Molnar:
"The main changes in this cycle's merge are:
- Implement shadow timekeeper to shorten in kernel reader side
blocking, by Thomas Gleixner.
- Posix timers enhancements by Pavel Emelyanov:
- allocate timer ID per process, so that exact timer ID allocations
can be re-created be checkpoint/restore code.
- debuggability and tooling (/proc/PID/timers, etc.) improvements.
- suspend/resume enhancements by Feng Tang: on certain new Intel Atom
processors (Penwell and Cloverview), there is a feature that the
TSC won't stop in S3 state, so the TSC value won't be reset to 0
after resume. This can be taken advantage of by the generic via
the CLOCK_SOURCE_SUSPEND_NONSTOP flag: instead of using the RTC to
recover/approximate sleep time, the main (and precise) clocksource
can be used.
- Fix /proc/timer_list for 4096 CPUs by Nathan Zimmer: on so many
CPUs the file goes beyond 4MB of size and thus the current
simplistic seqfile approach fails. Convert /proc/timer_list to a
proper seq_file with its own iterator.
- Cleanups and refactorings of the core timekeeping code by John
Stultz.
- International Atomic Clock time is managed by the NTP code
internally currently but not exposed externally. Separate the TAI
code out and add CLOCK_TAI support and TAI support to the hrtimer
and posix-timer code, by John Stultz.
- Add deep idle support enhacement to the broadcast clockevents core
timer code, by Daniel Lezcano: add an opt-in CLOCK_EVT_FEAT_DYNIRQ
clockevents feature (which will be utilized by future clockevents
driver updates), which allows the use of IRQ affinities to avoid
spurious wakeups of idle CPUs - the right CPU with an expiring
timer will be woken.
- Add new ARM bcm281xx clocksource driver, by Christian Daudt
- ... various other fixes and cleanups"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (52 commits)
clockevents: Set dummy handler on CPU_DEAD shutdown
timekeeping: Update tk->cycle_last in resume
posix-timers: Remove unused variable
clockevents: Switch into oneshot mode even if broadcast registered late
timer_list: Convert timer list to be a proper seq_file
timer_list: Split timer_list_show_tickdevices
posix-timers: Show sigevent info in proc file
posix-timers: Introduce /proc/PID/timers file
posix timers: Allocate timer id per process (v2)
timekeeping: Make sure to notify hrtimers when TAI offset changes
hrtimer: Fix ktime_add_ns() overflow on 32bit architectures
hrtimer: Add expiry time overflow check in hrtimer_interrupt
timekeeping: Shorten seq_count region
timekeeping: Implement a shadow timekeeper
timekeeping: Delay update of clock->cycle_last
timekeeping: Store cycle_last value in timekeeper struct as well
ntp: Remove ntp_lock, using the timekeeping locks to protect ntp state
timekeeping: Simplify tai updating from do_adjtimex
timekeeping: Hold timekeepering locks in do_adjtimex and hardpps
timekeeping: Move ADJ_SETOFFSET to top level do_adjtimex()
...
Pull SMP/hotplug changes from Ingo Molnar:
"This is a pretty large, multi-arch series unifying and generalizing
the various disjunct pieces of idle routines that architectures have
historically copied from each other and have grown in random, wildly
inconsistent and sometimes buggy directions:
101 files changed, 455 insertions(+), 1328 deletions(-)
this went through a number of review and test iterations before it was
committed, it was tested on various architectures, was exposed to
linux-next for quite some time - nevertheless it might cause problems
on architectures that don't read the mailing lists and don't regularly
test linux-next.
This cat herding excercise was motivated by the -rt kernel, and was
brought to you by Thomas "the Whip" Gleixner."
* 'smp-hotplug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (40 commits)
idle: Remove GENERIC_IDLE_LOOP config switch
um: Use generic idle loop
ia64: Make sure interrupts enabled when we "safe_halt()"
sparc: Use generic idle loop
idle: Remove unused ARCH_HAS_DEFAULT_IDLE
bfin: Fix typo in arch_cpu_idle()
xtensa: Use generic idle loop
x86: Use generic idle loop
unicore: Use generic idle loop
tile: Use generic idle loop
tile: Enter idle with preemption disabled
sh: Use generic idle loop
score: Use generic idle loop
s390: Use generic idle loop
powerpc: Use generic idle loop
parisc: Use generic idle loop
openrisc: Use generic idle loop
mn10300: Use generic idle loop
mips: Use generic idle loop
microblaze: Use generic idle loop
...
Pull scheduler changes from Ingo Molnar:
"The main changes in this development cycle were:
- full dynticks preparatory work by Frederic Weisbecker
- factor out the cpu time accounting code better, by Li Zefan
- multi-CPU load balancer cleanups and improvements by Joonsoo Kim
- various smaller fixes and cleanups"
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (45 commits)
sched: Fix init NOHZ_IDLE flag
sched: Prevent to re-select dst-cpu in load_balance()
sched: Rename load_balance_tmpmask to load_balance_mask
sched: Move up affinity check to mitigate useless redoing overhead
sched: Don't consider other cpus in our group in case of NEWLY_IDLE
sched: Explicitly cpu_idle_type checking in rebalance_domains()
sched: Change position of resched_cpu() in load_balance()
sched: Fix wrong rq's runnable_avg update with rt tasks
sched: Document task_struct::personality field
sched/cpuacct/UML: Fix header file dependency bug on the UML build
cgroup: Kill subsys.active flag
sched/cpuacct: No need to check subsys active state
sched/cpuacct: Initialize cpuacct subsystem earlier
sched/cpuacct: Initialize root cpuacct earlier
sched/cpuacct: Allocate per_cpu cpuusage for root cpuacct statically
sched/cpuacct: Clean up cpuacct.h
sched/cpuacct: Remove redundant NULL checks in cpuacct_acount_field()
sched/cpuacct: Remove redundant NULL checks in cpuacct_charge()
sched/cpuacct: Add cpuacct_acount_field()
sched/cpuacct: Add cpuacct_init()
...
Pull RCU updates from Ingo Molnar:
"The main changes in this cycle are mostly related to preparatory work
for the full-dynticks work:
- Remove restrictions on no-CBs CPUs, make RCU_FAST_NO_HZ take
advantage of numbered callbacks, do callback accelerations based on
numbered callbacks. Posted to LKML at
https://lkml.org/lkml/2013/3/18/960
- RCU documentation updates. Posted to LKML at
https://lkml.org/lkml/2013/3/18/570
- Miscellaneous fixes. Posted to LKML at
https://lkml.org/lkml/2013/3/18/594"
* 'core-rcu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (24 commits)
rcu: Make rcu_accelerate_cbs() note need for future grace periods
rcu: Abstract rcu_start_future_gp() from rcu_nocb_wait_gp()
rcu: Rename n_nocb_gp_requests to need_future_gp
rcu: Push lock release to rcu_start_gp()'s callers
rcu: Repurpose no-CBs event tracing to future-GP events
rcu: Rearrange locking in rcu_start_gp()
rcu: Make RCU_FAST_NO_HZ take advantage of numbered callbacks
rcu: Accelerate RCU callbacks at grace-period end
rcu: Export RCU_FAST_NO_HZ parameters to sysfs
rcu: Distinguish "rcuo" kthreads by RCU flavor
rcu: Add event tracing for no-CBs CPUs' grace periods
rcu: Add event tracing for no-CBs CPUs' callback registration
rcu: Introduce proper blocking to no-CBs kthreads GP waits
rcu: Provide compile-time control for no-CBs CPUs
rcu: Tone down debugging during boot-up and shutdown.
rcu: Add softirq-stall indications to stall-warning messages
rcu: Documentation update
rcu: Make bugginess of code sample more evident
rcu: Fix hlist_bl_set_first_rcu() annotation
rcu: Delete unused rcu_node "wakemask" field
...
Also enables cleanup of some 80-col trickery.
Cc: Richard Weinberger <richard@nod.at>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If the kernel was booted with the "quiet" boot option we have currently no
chance to see why an initrd fails. Change KERN_WARNING to KERN_ERR to see
what is going on.
Signed-off-by: Richard Weinberger <richard@nod.at>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As I was testing a lot of my code recently, and having several
"successes", I accidentally noticed in the dmesg this little line:
start_kernel(): bug: interrupts were enabled *very* early, fixing it
Sure enough, one of my patches two commits ago enabled interrupts early.
The sad part here is that I never noticed it, and I ran several tests with
ktest too, and ktest did not notice this line.
What ktest looks for (and so does many other automated testing scripts) is
a back trace produced by a WARN_ON() or BUG(). As a back trace was never
produced, my buggy patch could have slipped into linux-next, or even
worse, mainline.
Adding a WARN(!irqs_disabled()) makes this bug a little more obvious:
PID hash table entries: 4096 (order: 3, 32768 bytes)
__ex_table already sorted, skipping sort
Checking aperture...
No AGP bridge found
Calgary: detecting Calgary via BIOS EBDA area
Calgary: Unable to locate Rio Grande table in EBDA - bailing!
Memory: 2003252k/2054848k available (4857k kernel code, 460k absent, 51136k reserved, 6210k data, 1096k init)
------------[ cut here ]------------
WARNING: at /home/rostedt/work/git/linux-trace.git/init/main.c:543 start_kernel+0x21e/0x415()
Hardware name: To Be Filled By O.E.M.
Interrupts were enabled *very* early, fixing it
Modules linked in:
Pid: 0, comm: swapper/0 Not tainted 3.8.0-test+ #286
Call Trace:
warn_slowpath_common+0x83/0x9b
warn_slowpath_fmt+0x46/0x48
start_kernel+0x21e/0x415
x86_64_start_reservations+0x10e/0x112
x86_64_start_kernel+0x102/0x111
---[ end trace 007d8b0491b4f5d8 ]---
Preemptible hierarchical RCU implementation.
RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4.
NR_IRQS:4352 nr_irqs:712 16
Console: colour VGA+ 80x25
console [ttyS0] enabled, bootconsole disabled
Do you see it?
The original version of this patch just slapped a WARN_ON() in there and
kept the printk(). Ard van Breemen suggested using the WARN() interface,
which makes the code a bit cleaner.
Also, while examining other warnings in init/main.c, I found two other
locations that deserve a bloody murder scream if their conditions are hit,
and updated them accordingly.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Ard van Breemen <ard@telegraafnet.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Turn the full dynticks passive dependency on VIRT_CPU_ACCOUNTING_GEN
to an active one.
The full dynticks Kconfig is currently hidden behind the full dynticks
cputime accounting, which is an awkward and counter-intuitive layout:
the user first has to select the dynticks cputime accounting in order
to make the full dynticks feature to be visible.
We definetly want it the other way around. The usual way to perform
this kind of active dependency is use "select" on the depended target.
Now we can't use the Kconfig "select" instruction when the target is
a "choice".
So this patch inspires on how the RCU subsystem Kconfig interact
with its dependencies on SMP and PREEMPT: we make sure that cputime
accounting can't propose another option than VIRT_CPU_ACCOUNTING_GEN
when NO_HZ_FULL is selected by using the right "depends on" instruction
for each cputime accounting choices.
v2: Keep full dynticks cputime accounting available even without
full dynticks, as per Paul McKenney's suggestion.
Reported-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Hakan Akkan <hakanakkan@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Kevin Hilman <khilman@linaro.org>
Cc: Li Zhong <zhong@linux.vnet.ibm.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
We need full dynticks CPU to also be RCU nocb so
that we don't have to keep the tick to handle RCU
callbacks.
Make sure the range passed to nohz_full= boot
parameter is a subset of rcu_nocbs=
The CPUs that fail to meet this requirement will be
excluded from the nohz_full range. This is checked
early in boot time, before any CPU has the opportunity
to stop its tick.
Suggested-by: Steven Rostedt <rostedt@goodmis.org>
Reviewed-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Geoff Levand <geoff@infradead.org>
Cc: Gilad Ben Yossef <gilad@benyossef.com>
Cc: Hakan Akkan <hakanakkan@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Kevin Hilman <khilman@linaro.org>
Cc: Li Zhong <zhong@linux.vnet.ibm.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Pull RCU updates from Paul E. McKenney:
* Remove restrictions on no-CBs CPUs, make RCU_FAST_NO_HZ
take advantage of numbered callbacks, do additional callback
accelerations based on numbered callbacks. Posted to LKML
at https://lkml.org/lkml/2013/3/18/960.
* RCU documentation updates. Posted to LKML at
https://lkml.org/lkml/2013/3/18/570.
* Miscellaneous fixes. Posted to LKML at
https://lkml.org/lkml/2013/3/18/594.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
For now this calls cpu_idle(), but in the long run we want to move the
cpu bringup code to the core and therefor we add a state argument.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Paul McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Reviewed-by: Cc: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Cc: Magnus Damm <magnus.damm@gmail.com>
Link: http://lkml.kernel.org/r/20130321215233.583190032@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
We are planning to convert the dynticks Kconfig options layout
into a choice menu. The user must be able to easily pick
any of the following implementations: constant periodic tick,
idle dynticks, full dynticks.
As this implies a mutual exclusion, the two dynticks implementions
need to converge on the selection of a common Kconfig option in order
to ease the sharing of a common infrastructure.
It would thus seem pretty natural to reuse CONFIG_NO_HZ to
that end. It already implements all the idle dynticks code
and the full dynticks depends on all that code for now.
So ideally the choice menu would propose CONFIG_NO_HZ_IDLE and
CONFIG_NO_HZ_EXTENDED then both would select CONFIG_NO_HZ.
On the other hand we want to stay backward compatible: if
CONFIG_NO_HZ is set in an older config file, we want to
enable CONFIG_NO_HZ_IDLE by default.
But we can't afford both at the same time or we run into
a circular dependency:
1) CONFIG_NO_HZ_IDLE and CONFIG_NO_HZ_EXTENDED both select
CONFIG_NO_HZ
2) If CONFIG_NO_HZ is set, we default to CONFIG_NO_HZ_IDLE
We might be able to support that from Kconfig/Kbuild but it
may not be wise to introduce such a confusing behaviour.
So to solve this, create a new CONFIG_NO_HZ_COMMON option
which gathers the common code between idle and full dynticks
(that common code for now is simply the idle dynticks code)
and select it from their referring Kconfig.
Then we'll later create CONFIG_NO_HZ_IDLE and map CONFIG_NO_HZ
to it for backward compatibility.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Geoff Levand <geoff@infradead.org>
Cc: Gilad Ben Yossef <gilad@benyossef.com>
Cc: Hakan Akkan <hakanakkan@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Kevin Hilman <khilman@linaro.org>
Cc: Li Zhong <zhong@linux.vnet.ibm.com>
Cc: Namhyung Kim <namhyung.kim@lge.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Because RCU callbacks are now associated with the number of the grace
period that they must wait for, CPUs can now take advance callbacks
corresponding to grace periods that ended while a given CPU was in
dyntick-idle mode. This eliminates the need to try forcing the RCU
state machine while entering idle, thus reducing the CPU intensiveness
of RCU_FAST_NO_HZ, which should increase its energy efficiency.
Signed-off-by: Paul E. McKenney <paul.mckenney@linaro.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Currently, the per-no-CBs-CPU kthreads are named "rcuo" followed by
the CPU number, for example, "rcuo". This is problematic given that
there are either two or three RCU flavors, each of which gets a per-CPU
kthread with exactly the same name. This commit therefore introduces
a one-letter abbreviation for each RCU flavor, namely 'b' for RCU-bh,
'p' for RCU-preempt, and 's' for RCU-sched. This abbreviation is used
to distinguish the "rcuo" kthreads, for example, for CPU 0 we would have
"rcuob/0", "rcuop/0", and "rcuos/0".
Signed-off-by: Paul E. McKenney <paul.mckenney@linaro.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Tested-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Currently, the only way to specify no-CBs CPUs is via the rcu_nocbs
kernel command-line parameter. This is inconvenient in some cases,
particularly for randconfig testing, so this commit adds a new set of
kernel configuration parameters. CONFIG_RCU_NOCB_CPU_NONE (the default)
retains the old behavior, CONFIG_RCU_NOCB_CPU_ZERO offloads callback
processing from CPU 0 (along with any other CPUs specified by the
rcu_nocbs boot-time parameter), and CONFIG_RCU_NOCB_CPU_ALL offloads
callback processing from all CPUs.
Signed-off-by: Paul E. McKenney <paul.mckenney@linaro.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Remove "config EXPERIMENTAL" itself, now that every "depends on" it has
been removed from the tree.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, CPU 0 is constrained to not be a no-CBs CPU, and furthermore
at least one no-CBs CPU must remain online at any given time. These
restrictions are problematic in some situations, such as cases where
all CPUs must run a real-time workload that needs to be insulated from
OS jitter and latencies due to RCU callback invocation. This commit
therefore provides no-CBs CPUs a (very crude and energy-inefficient)
way to start and to wait for grace periods independently of the normal
RCU callback mechanisms. This approach allows any or all of the CPUs to
be designated as no-CBs CPUs, and allows any proper subset of the CPUs
(whether no-CBs CPUs or not) to be offlined.
This commit also provides a fix for a locking bug spotted by Xie
ChanglongX <changlongx.xie@intel.com>.
Signed-off-by: Paul E. McKenney <paul.mckenney@linaro.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Until we provide the nohz_mask boot parameter, keeping
the context tracking probes disabled by default is pointless
since what we want is to runtime test this code anyway.
It's furthermore confusing for the users which don't expect
the probes to be off when they select RCU user mode or full
dynticks cputime accounting.
Let's enable these probes selftests by default for now.
Suggested: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Li Zhong <zhong@linux.vnet.ibm.com>
Cc: Kevin Hilman <khilman@linaro.org>
Cc: Mats Liljegren <mats.liljegren@enea.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Namhyung Kim <namhyung.kim@lge.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
To convert the clockevents code to cpumask_var_t we need to move the
init call after the allocator setup.
Clockevents are earliest registered from time_init() as they need
interrupts being set up, so this is safe.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20130306111537.304379448@linutronix.de
Cc: Rusty Russell <rusty@rustcorp.com.au>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=NKkW
-----END PGP SIGNATURE-----
Merge tag 'arc-v3.9-rc1-late' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull new ARC architecture from Vineet Gupta:
"Initial ARC Linux port with some fixes on top for 3.9-rc1:
I would like to introduce the Linux port to ARC Processors (from
Synopsys) for 3.9-rc1. The patch-set has been discussed on the public
lists since Nov and has received a fair bit of review, specially from
Arnd, tglx, Al and other subsystem maintainers for DeviceTree, kgdb...
The arch bits are in arch/arc, some asm-generic changes (acked by
Arnd), a minor change to PARISC (acked by Helge).
The series is a touch bigger for a new port for 2 main reasons:
1. It enables a basic kernel in first sub-series and adds
ptrace/kgdb/.. later
2. Some of the fallout of review (DeviceTree support, multi-platform-
image support) were added on top of orig series, primarily to
record the revision history.
This updated pull request additionally contains
- fixes due to our GNU tools catching up with the new syscall/ptrace
ABI
- some (minor) cross-arch Kconfig updates."
* tag 'arc-v3.9-rc1-late' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc: (82 commits)
ARC: split elf.h into uapi and export it for userspace
ARC: Fixup the current ABI version
ARC: gdbserver using regset interface possibly broken
ARC: Kconfig cleanup tracking cross-arch Kconfig pruning in merge window
ARC: make a copy of flat DT
ARC: [plat-arcfpga] DT arc-uart bindings change: "baud" => "current-speed"
ARC: Ensure CONFIG_VIRT_TO_BUS is not enabled
ARC: Fix pt_orig_r8 access
ARC: [3.9] Fallout of hlist iterator update
ARC: 64bit RTSC timestamp hardware issue
ARC: Don't fiddle with non-existent caches
ARC: Add self to MAINTAINERS
ARC: Provide a default serial.h for uart drivers needing BASE_BAUD
ARC: [plat-arcfpga] defconfig for fully loaded ARC Linux
ARC: [Review] Multi-platform image #8: platform registers SMP callbacks
ARC: [Review] Multi-platform image #7: SMP common code to use callbacks
ARC: [Review] Multi-platform image #6: cpu-to-dma-addr optional
ARC: [Review] Multi-platform image #5: NR_IRQS defined by ARC core
ARC: [Review] Multi-platform image #4: Isolate platform headers
ARC: [Review] Multi-platform image #3: switch to board callback
...
Pull user namespace and namespace infrastructure changes from Eric W Biederman:
"This set of changes starts with a few small enhnacements to the user
namespace. reboot support, allowing more arbitrary mappings, and
support for mounting devpts, ramfs, tmpfs, and mqueuefs as just the
user namespace root.
I do my best to document that if you care about limiting your
unprivileged users that when you have the user namespace support
enabled you will need to enable memory control groups.
There is a minor bug fix to prevent overflowing the stack if someone
creates way too many user namespaces.
The bulk of the changes are a continuation of the kuid/kgid push down
work through the filesystems. These changes make using uids and gids
typesafe which ensures that these filesystems are safe to use when
multiple user namespaces are in use. The filesystems converted for
3.9 are ceph, 9p, afs, ocfs2, gfs2, ncpfs, nfs, nfsd, and cifs. The
changes for these filesystems were a little more involved so I split
the changes into smaller hopefully obviously correct changes.
XFS is the only filesystem that remains. I was hoping I could get
that in this release so that user namespace support would be enabled
with an allyesconfig or an allmodconfig but it looks like the xfs
changes need another couple of days before it they are ready."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace: (93 commits)
cifs: Enable building with user namespaces enabled.
cifs: Convert struct cifs_ses to use a kuid_t and a kgid_t
cifs: Convert struct cifs_sb_info to use kuids and kgids
cifs: Modify struct smb_vol to use kuids and kgids
cifs: Convert struct cifsFileInfo to use a kuid
cifs: Convert struct cifs_fattr to use kuid and kgids
cifs: Convert struct tcon_link to use a kuid.
cifs: Modify struct cifs_unix_set_info_args to hold a kuid_t and a kgid_t
cifs: Convert from a kuid before printing current_fsuid
cifs: Use kuids and kgids SID to uid/gid mapping
cifs: Pass GLOBAL_ROOT_UID and GLOBAL_ROOT_GID to keyring_alloc
cifs: Use BUILD_BUG_ON to validate uids and gids are the same size
cifs: Override unmappable incoming uids and gids
nfsd: Enable building with user namespaces enabled.
nfsd: Properly compare and initialize kuids and kgids
nfsd: Store ex_anon_uid and ex_anon_gid as kuids and kgids
nfsd: Modify nfsd4_cb_sec to use kuids and kgids
nfsd: Handle kuids and kgids in the nfs4acl to posix_acl conversion
nfsd: Convert nfsxdr to use kuids and kgids
nfsd: Convert nfs3xdr to use kuids and kgids
...
lockdep, but it's a mechanical change.
Cheers,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=tiSY
-----END PGP SIGNATURE-----
Merge tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull module update from Rusty Russell:
"The sweeping change is to make add_taint() explicitly indicate whether
to disable lockdep, but it's a mechanical change."
* tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
MODSIGN: Add option to not sign modules during modules_install
MODSIGN: Add -s <signature> option to sign-file
MODSIGN: Specify the hash algorithm on sign-file command line
MODSIGN: Simplify Makefile with a Kconfig helper
module: clean up load_module a little more.
modpost: Ignore ARC specific non-alloc sections
module: constify within_module_*
taint: add explicit flag to show whether lock dep is still OK.
module: printk message when module signature fail taints kernel.
Here is the big driver core merge for 3.9-rc1
There are two major series here, both of which touch lots of drivers all
over the kernel, and will cause you some merge conflicts:
- add a new function called devm_ioremap_resource() to properly be
able to check return values.
- remove CONFIG_EXPERIMENTAL
If you need me to provide a merged tree to handle these resolutions,
please let me know.
Other than those patches, there's not much here, some minor fixes and
updates.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlEmV0cACgkQMUfUDdst+yncCQCfbmnQZju7kzWXk6PjdFuKspT9
weAAoMCzcAtEzzc4LXuUxxG/sXBVBCjW
=yWAQ
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core patches from Greg Kroah-Hartman:
"Here is the big driver core merge for 3.9-rc1
There are two major series here, both of which touch lots of drivers
all over the kernel, and will cause you some merge conflicts:
- add a new function called devm_ioremap_resource() to properly be
able to check return values.
- remove CONFIG_EXPERIMENTAL
Other than those patches, there's not much here, some minor fixes and
updates"
Fix up trivial conflicts
* tag 'driver-core-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (221 commits)
base: memory: fix soft/hard_offline_page permissions
drivercore: Fix ordering between deferred_probe and exiting initcalls
backlight: fix class_find_device() arguments
TTY: mark tty_get_device call with the proper const values
driver-core: constify data for class_find_device()
firmware: Ignore abort check when no user-helper is used
firmware: Reduce ifdef CONFIG_FW_LOADER_USER_HELPER
firmware: Make user-mode helper optional
firmware: Refactoring for splitting user-mode helper code
Driver core: treat unregistered bus_types as having no devices
watchdog: Convert to devm_ioremap_resource()
thermal: Convert to devm_ioremap_resource()
spi: Convert to devm_ioremap_resource()
power: Convert to devm_ioremap_resource()
mtd: Convert to devm_ioremap_resource()
mmc: Convert to devm_ioremap_resource()
mfd: Convert to devm_ioremap_resource()
media: Convert to devm_ioremap_resource()
iommu: Convert to devm_ioremap_resource()
drm: Convert to devm_ioremap_resource()
...
Pull async changes from Tejun Heo:
"These are followups for the earlier deadlock issue involving async
ending up waiting for itself through block requesting module[1]. The
following changes are made by these commits.
- Instead of requesting default elevator on each request_queue init,
block now requests it once early during boot.
- Kmod triggers warning if invoked from an async worker.
- Async synchronization implementation has been reimplemented. It's
a lot simpler now."
* 'for-3.9-async' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
async: initialise list heads to fix crash
async: replace list of active domains with global list of pending items
async: keep pending tasks on async_domain and remove async_pending
async: use ULLONG_MAX for infinity cookie value
async: bring sanity to the use of words domain and running
async, kmod: warn on synchronous request_module() from async workers
block: don't request module during elevator init
init, block: try to load default elevator module early during boot
Pull scheduler changes from Ingo Molnar:
"Main changes:
- scheduler side full-dynticks (user-space execution is undisturbed
and receives no timer IRQs) preparation changes that convert the
cputime accounting code to be full-dynticks ready, from Frederic
Weisbecker.
- Initial sched.h split-up changes, by Clark Williams
- select_idle_sibling() performance improvement by Mike Galbraith:
" 1 tbench pair (worst case) in a 10 core + SMT package:
pre 15.22 MB/sec 1 procs
post 252.01 MB/sec 1 procs "
- sched_rr_get_interval() ABI fix/change. We think this detail is not
used by apps (so it's not an ABI in practice), but lets keep it
under observation.
- misc RT scheduling cleanups, optimizations"
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (24 commits)
sched/rt: Add <linux/sched/rt.h> header to <linux/init_task.h>
cputime: Remove irqsave from seqlock readers
sched, powerpc: Fix sched.h split-up build failure
cputime: Restore CPU_ACCOUNTING config defaults for PPC64
sched/rt: Move rt specific bits into new header file
sched/rt: Add a tuning knob to allow changing SCHED_RR timeslice
sched: Move sched.h sysctl bits into separate header
sched: Fix signedness bug in yield_to()
sched: Fix select_idle_sibling() bouncing cow syndrome
sched/rt: Further simplify pick_rt_task()
sched/rt: Do not account zero delta_exec in update_curr_rt()
cputime: Safely read cputime of full dynticks CPUs
kvm: Prepare to add generic guest entry/exit callbacks
cputime: Use accessors to read task cputime stats
cputime: Allow dynamic switch between tick/virtual based cputime accounting
cputime: Generic on-demand virtual cputime accounting
cputime: Move default nsecs_to_cputime() to jiffies based cputime file
cputime: Librarize per nsecs resolution cputime definitions
cputime: Avoid multiplication overflow on utime scaling
context_tracking: Export context state for generic vtime
...
Fix up conflict in kernel/context_tracking.c due to comment additions.
Pull irq core changes from Ingo Molnar:
"The biggest changes are the IRQ-work and printk changes from Frederic
Weisbecker, which prepare the code for 'full dynticks' (the ability to
stop or slow down the periodic tick arbitrarily, not just in idle time
as today):
- Don't stop tick with irq works pending. This fix is generally
useful and concerns archs that can't raise self IPIs.
- Flush irq works before CPU offlining.
- Introduce "lazy" irq works that can wait for the next tick to be
executed, unless it's stopped.
- Implement klogd wake up using irq work. This removes the ad-hoc
printk_tick()/printk_needs_cpu() hooks and make it working even in
dynticks mode.
- Cleanups and fixes."
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq: Export enable/disable_percpu_irq()
arch Kconfig: Remove references to IRQ_PER_CPU
irq_work: Remove return value from the irq_work_queue() function
genirq: Avoid deadlock in spurious handling
printk: Wake up klogd using irq_work
irq_work: Make self-IPIs optable
irq_work: Warn if there's still work on cpu_down
irq_work: Flush work on CPU_DYING
irq_work: Don't stop the tick with pending works
nohz: Add API to check tick state
irq_work: Remove CONFIG_HAVE_IRQ_WORK
irq_work: Fix racy check on work pending flag
irq_work: Fix racy IRQ_WORK_BUSY flag setting
PARISC defines /proc/sys/kernel/unaligned-trap to runtime toggle
unaligned access emulation.
The exact mechanics of enablig/disabling are still arch specific, we can
make the sysctl usable by other arches.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Acked-by: Helge Deller <deller@gmx.de>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Helge Deller <deller@gmx.de>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Serge Hallyn <serge.hallyn@canonical.com>
Now that the kuids and kgids conversion have propogated
through net/sunrpc/ and the fs/nfsd/ it is safe to enable
building nfsd when user namespaces are enabled.
Cc: "J. Bruce Fields" <bfields@fieldses.org>
Cc: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Now that the kuids and kgids conversion have propogated
through net/sunrpc/ and the fs/nfs/ it is safe to enable
building nfs when user namespaces are enabled.
Cc: "J. Bruce Fields" <bfields@fieldses.org>
Cc: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
ncpfs does not natively support uids and gids so this conversion was
simply a matter of updating the the type of the mounteduid, the uid
and the gid on the superblock. Fixing the ioctls that read them,
updating the mount option parser and the mount option printer.
Cc: Petr Vandrovec <petr@vandrovec.name>
Acked-by: Serge Hallyn <serge.hallyn@canonical.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Now that all of the necessary work has been done to push kuids and
kgids throughout gfs2 and to convert between kuids and kgids when
reading and writing the on disk structures it is safe to enable gfs2
when multiple user namespaces are enabled.
Cc: Steven Whitehouse <swhiteho@redhat.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Now that ocfs2 has been converted to store uids and gids in
kuid_t and kgid_t and all of the conversions have been added
to the appropriate places it is safe to allow building and
using ocfs2 with user namespace support enabled.
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Joel Becker <jlbec@evilplan.org>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Now that the coda kernel to userspace has been modified to convert
between kuids and kgids and uids and gids, and all internal
coda structures have be modified to store uids and gids as
kuids and kgids it is safe to allow code to be built with
user namespace support enabled.
Cc: Jan Harkes <jaharkes@cs.cmu.edu>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Modify struct afs_file_status to store owner as a kuid_t and group as
a kgid_t.
In xdr_decode_AFSFetchStatus as owner is now a kuid_t and group is now
a kgid_t don't use the EXTRACT macro. Instead perform the work of
the extract macro explicitly. Read the value with ntohl and
convert it to the appropriate type with make_kuid or make_kgid.
Test if the value is different from what is stored in status and
update changed. Update the value in status.
In xdr_encode_AFS_StoreStatus call from_kuid or from_kgid as
we are computing the on the wire encoding.
Initialize uids with GLOBAL_ROOT_UID instead of 0.
Initialize gids with GLOBAL_ROOT_GID instead of 0.
Cc: David Howells <dhowells@redhat.com>
Acked-by: Serge Hallyn <serge.hallyn@canonical.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Now that the uid_t -> kuid_t, gid_t -> kgid_t conversion
has been completed in 9p allow 9p to be built when user
namespaces are enabled.
Cc: Eric Van Hensbergen <ericvh@gmail.com>
Cc: Ron Minnich <rminnich@gmail.com>
Cc: Latchesar Ionkov <lucho@ionkov.net>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Now that conversions happen from kuids and kgids when generating ceph
messages and conversion happen to kuids and kgids after receiving
celph messages, and all intermediate data structures store uids and
gids as type kuid_t and kgid_t it is safe to enable ceph with
user namespace support enabled.
Cc: Sage Weil <sage@inktank.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Move rt scheduler definitions out of include/linux/sched.h into
new file include/linux/sched/rt.h
Signed-off-by: Clark Williams <williams@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Link: http://lkml.kernel.org/r/20130207094707.7b9f825f@riff.lan
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Move the sysctl-related bits from include/linux/sched.h into
a new file: include/linux/sched/sysctl.h. Then update source
files requiring access to those bits by including the new
header file.
Signed-off-by: Clark Williams <williams@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Link: http://lkml.kernel.org/r/20130207094659.06dced96@riff.lan
Signed-off-by: Ingo Molnar <mingo@kernel.org>
All in-kernel users of class_find_device() don't really need mutable
data for match callback.
In two places (kernel/power/suspend_test.c, drivers/scsi/osd/osd_uld.c)
this patch changes match callbacks to use const search data.
The const is propagated to rtc_class_open() and power_supply_get_by_name()
parameters.
Note that there's a dev reference leak in suspend_test.c that's not
touched in this patch.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Typical cputime stats infrastructure relies on the timer tick and
its periodic polling on the CPU to account the amount of time
spent by the CPUs and the tasks per high level domains such as
userspace, kernelspace, guest, ...
Now we are preparing to implement full dynticks capability on
Linux for Real Time and HPC users who want full CPU isolation.
This feature requires a cputime accounting that doesn't depend
on the timer tick.
To implement it, this new cputime infrastructure plugs into
kernel/user/guest boundaries to take snapshots of cputime and
flush these to the stats when needed. This performs pretty
much like CONFIG_VIRT_CPU_ACCOUNTING except that context location
and cputime snaphots are synchronized between write and read
side such that the latter can safely retrieve the pending tickless
cputime of a task and add it to its latest cputime snapshot to
return the correct result to the user.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=1Tzp
-----END PGP SIGNATURE-----
Merge tag 'full-dynticks-cputime-for-mingo' of git://git.kernel.org/pub/scm/linux/kernel/git/frederic/linux-dynticks into sched/core
Pull full-dynticks (user-space execution is undisturbed and
receives no timer IRQs) preparation changes that convert the
cputime accounting code to be full-dynticks ready,
from Frederic Weisbecker:
"This implements the cputime accounting on full dynticks CPUs.
Typical cputime stats infrastructure relies on the timer tick and
its periodic polling on the CPU to account the amount of time
spent by the CPUs and the tasks per high level domains such as
userspace, kernelspace, guest, ...
Now we are preparing to implement full dynticks capability on
Linux for Real Time and HPC users who want full CPU isolation.
This feature requires a cputime accounting that doesn't depend
on the timer tick.
To implement it, this new cputime infrastructure plugs into
kernel/user/guest boundaries to take snapshots of cputime and
flush these to the stats when needed. This performs pretty
much like CONFIG_VIRT_CPU_ACCOUNTING except that context location
and cputime snaphots are synchronized between write and read
side such that the latter can safely retrieve the pending tickless
cputime of a task and add it to its latest cputime snapshot to
return the correct result to the user."
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Conflicts:
kernel/irq_work.c
Add support for printk in full dynticks CPU.
* Don't stop tick with irq works pending. This
fix is generally useful and concerns archs that
can't raise self IPIs.
* Flush irq works before CPU offlining.
* Introduce "lazy" irq works that can wait for the
next tick to be executed, unless it's stopped.
* Implement klogd wake up using irq work. This
removes the ad-hoc printk_tick()/printk_needs_cpu()
hooks and make it working even in dynticks mode.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Pull x86 fixes from Peter Anvin:
"This is a collection of miscellaneous fixes, the most important one is
the fix for the Samsung laptop bricking issue (auto-blacklisting the
samsung-laptop driver); the efi_enabled() changes you see below are
prerequisites for that fix.
The other issues fixed are booting on OLPC XO-1.5, an UV fix, NMI
debugging, and requiring CAP_SYS_RAWIO for MSR references, just as
with I/O port references."
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
samsung-laptop: Disable on EFI hardware
efi: Make 'efi_enabled' a function to query EFI facilities
smp: Fix SMP function call empty cpu mask race
x86/msr: Add capabilities check
x86/dma-debug: Bump PREALLOC_DMA_DEBUG_ENTRIES
x86/olpc: Fix olpc-xo1-sci.c build errors
arch/x86/platform/uv: Fix incorrect tlb flush all issue
x86-64: Fix unwind annotations in recent NMI changes
x86-32: Start out cr0 clean, disable paging before modifying cr3/4
Originally 'efi_enabled' indicated whether a kernel was booted from
EFI firmware. Over time its semantics have changed, and it now
indicates whether or not we are booted on an EFI machine with
bit-native firmware, e.g. 64-bit kernel with 64-bit firmware.
The immediate motivation for this patch is the bug report at,
https://bugs.launchpad.net/ubuntu-cdimage/+bug/1040557
which details how running a platform driver on an EFI machine that is
designed to run under BIOS can cause the machine to become
bricked. Also, the following report,
https://bugzilla.kernel.org/show_bug.cgi?id=47121
details how running said driver can also cause Machine Check
Exceptions. Drivers need a new means of detecting whether they're
running on an EFI machine, as sadly the expression,
if (!efi_enabled)
hasn't been a sufficient condition for quite some time.
Users actually want to query 'efi_enabled' for different reasons -
what they really want access to is the list of available EFI
facilities.
For instance, the x86 reboot code needs to know whether it can invoke
the ResetSystem() function provided by the EFI runtime services, while
the ACPI OSL code wants to know whether the EFI config tables were
mapped successfully. There are also checks in some of the platform
driver code to simply see if they're running on an EFI machine (which
would make it a bad idea to do BIOS-y things).
This patch is a prereq for the samsung-laptop fix patch.
Cc: David Airlie <airlied@linux.ie>
Cc: Corentin Chary <corentincj@iksaif.net>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Dave Jiang <dave.jiang@intel.com>
Cc: Olof Johansson <olof@lixom.net>
Cc: Peter Jones <pjones@redhat.com>
Cc: Colin Ian King <colin.king@canonical.com>
Cc: Steve Langasek <steve.langasek@canonical.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Konrad Rzeszutek Wilk <konrad@kernel.org>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: <stable@vger.kernel.org>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
The TINY_PREEMPT_RCU is complex, does not provide that much memory
savings, and therefore TREE_PREEMPT_RCU should be used instead. The
systems where the difference between TINY_PREEMPT_RCU and TREE_PREEMPT_RCU
are quite small compared to the memory footprint of CONFIG_PREEMPT.
This commit therefore takes a first step towards eliminating
TINY_PREEMPT_RCU by allowing TREE_PREEMPT_RCU to be configured on !SMP
systems.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Tiny RCU has historically omitted RCU CPU stall warnings in order to
reduce memory requirements, however, lack of these warnings caused
Thomas Gleixner some debugging pain recently. Therefore, this commit
adds RCU CPU stall warnings to tiny RCU if RCU_TRACE=y. This keeps
the memory footprint small, while still enabling CPU stall warnings
in kernels built to enable them.
Updated to include Josh Triplett's suggested use of RCU_STALL_COMMON
config variable to simplify #if expressions.
Reported-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Paul E. McKenney <paul.mckenney@linaro.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
If we want to stop the tick further idle, we need to be
able to account the cputime without using the tick.
Virtual based cputime accounting solves that problem by
hooking into kernel/user boundaries.
However implementing CONFIG_VIRT_CPU_ACCOUNTING require
low level hooks and involves more overhead. But we already
have a generic context tracking subsystem that is required
for RCU needs by archs which plan to shut down the tick
outside idle.
This patch implements a generic virtual based cputime
accounting that relies on these generic kernel/user hooks.
There are some upsides of doing this:
- This requires no arch code to implement CONFIG_VIRT_CPU_ACCOUNTING
if context tracking is already built (already necessary for RCU in full
tickless mode).
- We can rely on the generic context tracking subsystem to dynamically
(de)activate the hooks, so that we can switch anytime between virtual
and tick based accounting. This way we don't have the overhead
of the virtual accounting when the tick is running periodically.
And one downside:
- There is probably more overhead than a native virtual based cputime
accounting. But this relies on hooks that are already set anyway.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Li Zhong <zhong@linux.vnet.ibm.com>
Cc: Namhyung Kim <namhyung.kim@lge.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
In the help text describing user namespaces recommend use of memory
control groups. In many cases memory control groups are the only
mechanism there is to limit how much memory a user who can create
user namespaces can use.
Acked-by: Serge Hallyn <serge.hallyn@canonical.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
To allow the builder to sign only a subset of modules, or to sign the
modules using a key that is not available on the build machine, add
CONFIG_MODULE_SIG_ALL. If this option is unset, no modules will be
signed during build. The default is 'y', to preserve the current
behavior.
Signed-off-by: Michal Marek <mmarek@suse.cz>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Pull misc syscall fixes from Al Viro:
- compat syscall fixes (discussed back in December)
- a couple of "make life easier for sigaltstack stuff by reducing
inter-tree dependencies"
- fix up compiler/asmlinkage calling convention disagreement of
sys_clone()
- misc
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/signal:
sys_clone() needs asmlinkage_protect
make sure that /linuxrc has std{in,out,err}
x32: fix sigtimedwait
x32: fix waitid()
switch compat_sys_wait4() and compat_sys_waitid() to COMPAT_SYSCALL_DEFINE
switch compat_sys_sigaltstack() to COMPAT_SYSCALL_DEFINE
CONFIG_GENERIC_SIGALTSTACK build breakage with asm-generic/syscalls.h
Ensure that kernel_init_freeable() is not inlined into non __init code
This patch adds default module loading and uses it to load the default
block elevator. During boot, it's called right after initramfs or
initrd is made available and right before control is passed to
userland. This ensures that as long as the modules are available in
the usual places in initramfs, initrd or the root filesystem, the
default modules are loaded as soon as possible.
This will replace the on-demand elevator module loading from elevator
init path.
v2: Fixed build breakage when !CONFIG_BLOCK. Reported by kbuild test
robot.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Alex Riesen <raa.lkml@gmail.com>
Cc: Fengguang We <fengguang.wu@intel.com>
This is to fix up a build problem with a wireless driver due to the
dynamic-debug patches in this branch.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In commit 281dc5c5ec ("Give up on pushing CC_OPTIMIZE_FOR_SIZE") we
already changed the actual default value, but the help-text still
suggested 'y'. Fix the help text too, for all the same reasons.
Sadly, -Os keeps on generating some very suboptimal code for certain
cases, to the point where any I$ miss upside is swamped by the downside.
The main ones are:
- using "rep movsb" for memcpy, even on CPU's where that is
horrendously bad for performance.
- not honoring branch prediction information, so any I$ footprint you
win from smaller code, you lose from less code density in the I$.
- using divide instructions when that is very expensive.
Signed-off-by: Kirill Smelkov <kirr@mns.spb.ru>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The CONFIG_EXPERIMENTAL config item has not carried much meaning for a
while now and is almost always enabled by default. As agreed during the
Linux kernel summit, remove it from any "depends on" lines in Kconfigs.
CC: "Eric W. Biederman" <ebiederm@xmission.com>
CC: Serge Hallyn <serge.hallyn@canonical.com>
CC: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
CC: Andrew Morton <akpm@linux-foundation.org>
CC: Frederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Serge Hallyn <serge.hallyn@ubuntu.com>
This config item has not carried much meaning for a while now and is
almost always enabled by default (especially in distro builds). As agreed
during the Linux kernel summit, it should be removed. As a first step,
remove it from being listed, and default it to on. Once it has been
removed from all subsystem Kconfigs, it will be dropped entirely.
For items that really are experimental, maintainers should use "default
n", optionally include "(EXPERIMENTAL)" in the title, and add language to
the help text indicating why the item should be considered experimental.
For items that are dangerously experimental, the maintainer is encouraged
to follow the above title recommendation, add stronger language to the
help text, and optionally use (depending on the extent of the danger,
from least to most dangerous): printk(), add_taint(TAINT_WARN),
add_taint(TAINT_CRAP), WARN_ON(1), and CONFIG_BROKEN.
CC: Greg KH <gregkh@linuxfoundation.org>
CC: "Eric W. Biederman" <ebiederm@xmission.com>
CC: Serge Hallyn <serge.hallyn@canonical.com>
CC: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
CC: Andrew Morton <akpm@linux-foundation.org>
CC: Frederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Serge Hallyn <serge.hallyn@canonical.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
IA64 defines /proc/sys/kernel/ignore-unaligned-usertrap to control
verbose warnings on unaligned access emulation.
Although the exact mechanics of what to do with sysctl (ignore/shout)
are arch specific, this change enables the sysctl to be usable cross-arch.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Serge Hallyn <serge.hallyn@canonical.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Commit d6b2123802 "make sure that we always have a return path from
kernel_execve()" reshuffled kernel_init()/init_post() to ensure that
kernel_execve() has a caller to return to.
It removed __init annotation for kernel_init() and introduced/calls a
new routine kernel_init_freeable(). Latter however is inlined by any
reasonable compiler (ARC gcc 4.4 in this case), causing slight code
bloat.
This patch forces kernel_init_freeable() as noinline reducing the .text
bloat-o-meter vmlinux vmlinux_new
add/remove: 1/0 grow/shrink: 0/1 up/down: 374/-334 (40)
function old new delta
kernel_init_freeable - 374 +374 (.init.text)
kernel_init 628 294 -334 (.text)
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Pull signal handling cleanups from Al Viro:
"sigaltstack infrastructure + conversion for x86, alpha and um,
COMPAT_SYSCALL_DEFINE infrastructure.
Note that there are several conflicts between "unify
SS_ONSTACK/SS_DISABLE definitions" and UAPI patches in mainline;
resolution is trivial - just remove definitions of SS_ONSTACK and
SS_DISABLED from arch/*/uapi/asm/signal.h; they are all identical and
include/uapi/linux/signal.h contains the unified variant."
Fixed up conflicts as per Al.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/signal:
alpha: switch to generic sigaltstack
new helpers: __save_altstack/__compat_save_altstack, switch x86 and um to those
generic compat_sys_sigaltstack()
introduce generic sys_sigaltstack(), switch x86 and um to it
new helper: compat_user_stack_pointer()
new helper: restore_altstack()
unify SS_ONSTACK/SS_DISABLE definitions
new helper: current_user_stack_pointer()
missing user_stack_pointer() instances
Bury the conditionals from kernel_thread/kernel_execve series
COMPAT_SYSCALL_DEFINE: infrastructure
All architectures have
CONFIG_GENERIC_KERNEL_THREAD
CONFIG_GENERIC_KERNEL_EXECVE
__ARCH_WANT_SYS_EXECVE
None of them have __ARCH_WANT_KERNEL_EXECVE and there are only two callers
of kernel_execve() (which is a trivial wrapper for do_execve() now) left.
Kill the conditionals and make both callers use do_execve().
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The page allocator is able to bind a page to a memcg when it is
allocated. But for the caches, we'd like to have as many objects as
possible in a page belonging to the same cache.
This is done in this patch by calling memcg_kmem_get_cache in the
beginning of every allocation function. This function is patched out by
static branches when kernel memory controller is not being used.
It assumes that the task allocating, which determines the memcg in the
page allocator, belongs to the same cgroup throughout the whole process.
Misaccounting can happen if the task calls memcg_kmem_get_cache() while
belonging to a cgroup, and later on changes. This is considered
acceptable, and should only happen upon task migration.
Before the cache is created by the memcg core, there is also a possible
imbalance: the task belongs to a memcg, but the cache being allocated from
is the global cache, since the child cache is not yet guaranteed to be
ready. This case is also fine, since in this case the GFP_KMEMCG will not
be passed and the page allocator will not attempt any cgroup accounting.
Signed-off-by: Glauber Costa <glommer@parallels.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Frederic Weisbecker <fweisbec@redhat.com>
Cc: Greg Thelen <gthelen@google.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: JoonSoo Kim <js1304@gmail.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Rik van Riel <riel@redhat.com>
Cc: Suleiman Souhlal <suleiman@google.com>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add the basic infrastructure for the accounting of kernel memory. To
control that, the following files are created:
* memory.kmem.usage_in_bytes
* memory.kmem.limit_in_bytes
* memory.kmem.failcnt
* memory.kmem.max_usage_in_bytes
They have the same meaning of their user memory counterparts. They
reflect the state of the "kmem" res_counter.
Per cgroup kmem memory accounting is not enabled until a limit is set for
the group. Once the limit is set the accounting cannot be disabled for
that group. This means that after the patch is applied, no behavioral
changes exists for whoever is still using memcg to control their memory
usage, until memory.kmem.limit_in_bytes is set for the first time.
We always account to both user and kernel resource_counters. This
effectively means that an independent kernel limit is in place when the
limit is set to a lower value than the user memory. A equal or higher
value means that the user limit will always hit first, meaning that kmem
is effectively unlimited.
People who want to track kernel memory but not limit it, can set this
limit to a very high number (like RESOURCE_MAX - 1page - that no one will
ever hit, or equal to the user memory)
[akpm@linux-foundation.org: MEMCG_MMEM only works with slab and slub]
Signed-off-by: Glauber Costa <glommer@parallels.com>
Acked-by: Kamezawa Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Acked-by: Michal Hocko <mhocko@suse.cz>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: Christoph Lameter <cl@linux.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Frederic Weisbecker <fweisbec@redhat.com>
Cc: Greg Thelen <gthelen@google.com>
Cc: JoonSoo Kim <js1304@gmail.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull user namespace changes from Eric Biederman:
"While small this set of changes is very significant with respect to
containers in general and user namespaces in particular. The user
space interface is now complete.
This set of changes adds support for unprivileged users to create user
namespaces and as a user namespace root to create other namespaces.
The tyranny of supporting suid root preventing unprivileged users from
using cool new kernel features is broken.
This set of changes completes the work on setns, adding support for
the pid, user, mount namespaces.
This set of changes includes a bunch of basic pid namespace
cleanups/simplifications. Of particular significance is the rework of
the pid namespace cleanup so it no longer requires sending out
tendrils into all kinds of unexpected cleanup paths for operation. At
least one case of broken error handling is fixed by this cleanup.
The files under /proc/<pid>/ns/ have been converted from regular files
to magic symlinks which prevents incorrect caching by the VFS,
ensuring the files always refer to the namespace the process is
currently using and ensuring that the ptrace_mayaccess permission
checks are always applied.
The files under /proc/<pid>/ns/ have been given stable inode numbers
so it is now possible to see if different processes share the same
namespaces.
Through the David Miller's net tree are changes to relax many of the
permission checks in the networking stack to allowing the user
namespace root to usefully use the networking stack. Similar changes
for the mount namespace and the pid namespace are coming through my
tree.
Two small changes to add user namespace support were commited here adn
in David Miller's -net tree so that I could complete the work on the
/proc/<pid>/ns/ files in this tree.
Work remains to make it safe to build user namespaces and 9p, afs,
ceph, cifs, coda, gfs2, ncpfs, nfs, nfsd, ocfs2, and xfs so the
Kconfig guard remains in place preventing that user namespaces from
being built when any of those filesystems are enabled.
Future design work remains to allow root users outside of the initial
user namespace to mount more than just /proc and /sys."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace: (38 commits)
proc: Usable inode numbers for the namespace file descriptors.
proc: Fix the namespace inode permission checks.
proc: Generalize proc inode allocation
userns: Allow unprivilged mounts of proc and sysfs
userns: For /proc/self/{uid,gid}_map derive the lower userns from the struct file
procfs: Print task uids and gids in the userns that opened the proc file
userns: Implement unshare of the user namespace
userns: Implent proc namespace operations
userns: Kill task_user_ns
userns: Make create_new_namespaces take a user_ns parameter
userns: Allow unprivileged use of setns.
userns: Allow unprivileged users to create new namespaces
userns: Allow setting a userns mapping to your current uid.
userns: Allow chown and setgid preservation
userns: Allow unprivileged users to create user namespaces.
userns: Ignore suid and sgid on binaries if the uid or gid can not be mapped
userns: fix return value on mntns_install() failure
vfs: Allow unprivileged manipulation of the mount namespace.
vfs: Only support slave subtrees across different user namespaces
vfs: Add a user namespace reference from struct mnt_namespace
...
Pull block driver update from Jens Axboe:
"Now that the core bits are in, here are the driver bits for 3.8. The
branch contains:
- A huge pile of drbd bits that were dumped from the 3.7 merge
window. Following that, it was both made perfectly clear that
there is going to be no more over-the-wall pulls and how the
situation on individual pulls can be improved.
- A few cleanups from Akinobu Mita for drbd and cciss.
- Queue improvement for loop from Lukas. This grew into adding a
generic interface for waiting/checking an even with a specific
lock, allowing this to be pulled out of md and now loop and drbd is
also using it.
- A few fixes for xen back/front block driver from Roger Pau Monne.
- Partition improvements from Stephen Warren, allowing partiion UUID
to be used as an identifier."
* 'for-3.8/drivers' of git://git.kernel.dk/linux-block: (609 commits)
drbd: update Kconfig to match current dependencies
drbd: Fix drbdsetup wait-connect, wait-sync etc... commands
drbd: close race between drbd_set_role and drbd_connect
drbd: respect no-md-barriers setting also when changed online via disk-options
drbd: Remove obsolete check
drbd: fixup after wait_even_lock_irq() addition to generic code
loop: Limit the number of requests in the bio list
wait: add wait_event_lock_irq() interface
xen-blkfront: free allocated page
xen-blkback: move free persistent grants code
block: partition: msdos: provide UUIDs for partitions
init: reduce PARTUUID min length to 1 from 36
block: store partition_meta_info.uuid as a string
cciss: use check_signature()
cciss: cleanup bitops usage
drbd: use copy_highpage
drbd: if the replication link breaks during handshake, keep retrying
drbd: check return of kmalloc in receive_uuids
drbd: Broadcast sync progress no more often than once per second
drbd: don't try to clear bits once the disk has failed
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)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=ivQa
-----END PGP SIGNATURE-----
Merge tag 'balancenuma-v11' of git://git.kernel.org/pub/scm/linux/kernel/git/mel/linux-balancenuma
Pull Automatic NUMA Balancing bare-bones from Mel Gorman:
"There are three implementations for NUMA balancing, this tree
(balancenuma), numacore which has been developed in tip/master and
autonuma which is in aa.git.
In almost all respects balancenuma is the dumbest of the three because
its main impact is on the VM side with no attempt to be smart about
scheduling. In the interest of getting the ball rolling, it would be
desirable to see this much merged for 3.8 with the view to building
scheduler smarts on top and adapting the VM where required for 3.9.
The most recent set of comparisons available from different people are
mel: https://lkml.org/lkml/2012/12/9/108
mingo: https://lkml.org/lkml/2012/12/7/331
tglx: https://lkml.org/lkml/2012/12/10/437
srikar: https://lkml.org/lkml/2012/12/10/397
The results are a mixed bag. In my own tests, balancenuma does
reasonably well. It's dumb as rocks and does not regress against
mainline. On the other hand, Ingo's tests shows that balancenuma is
incapable of converging for this workloads driven by perf which is bad
but is potentially explained by the lack of scheduler smarts. Thomas'
results show balancenuma improves on mainline but falls far short of
numacore or autonuma. Srikar's results indicate we all suffer on a
large machine with imbalanced node sizes.
My own testing showed that recent numacore results have improved
dramatically, particularly in the last week but not universally.
We've butted heads heavily on system CPU usage and high levels of
migration even when it shows that overall performance is better.
There are also cases where it regresses. Of interest is that for
specjbb in some configurations it will regress for lower numbers of
warehouses and show gains for higher numbers which is not reported by
the tool by default and sometimes missed in treports. Recently I
reported for numacore that the JVM was crashing with
NullPointerExceptions but currently it's unclear what the source of
this problem is. Initially I thought it was in how numacore batch
handles PTEs but I'm no longer think this is the case. It's possible
numacore is just able to trigger it due to higher rates of migration.
These reports were quite late in the cycle so I/we would like to start
with this tree as it contains much of the code we can agree on and has
not changed significantly over the last 2-3 weeks."
* tag 'balancenuma-v11' of git://git.kernel.org/pub/scm/linux/kernel/git/mel/linux-balancenuma: (50 commits)
mm/rmap, migration: Make rmap_walk_anon() and try_to_unmap_anon() more scalable
mm/rmap: Convert the struct anon_vma::mutex to an rwsem
mm: migrate: Account a transhuge page properly when rate limiting
mm: numa: Account for failed allocations and isolations as migration failures
mm: numa: Add THP migration for the NUMA working set scanning fault case build fix
mm: numa: Add THP migration for the NUMA working set scanning fault case.
mm: sched: numa: Delay PTE scanning until a task is scheduled on a new node
mm: sched: numa: Control enabling and disabling of NUMA balancing if !SCHED_DEBUG
mm: sched: numa: Control enabling and disabling of NUMA balancing
mm: sched: Adapt the scanning rate if a NUMA hinting fault does not migrate
mm: numa: Use a two-stage filter to restrict pages being migrated for unlikely task<->node relationships
mm: numa: migrate: Set last_nid on newly allocated page
mm: numa: split_huge_page: Transfer last_nid on tail page
mm: numa: Introduce last_nid to the page frame
sched: numa: Slowly increase the scanning period as NUMA faults are handled
mm: numa: Rate limit setting of pte_numa if node is saturated
mm: numa: Rate limit the amount of memory that is migrated between nodes
mm: numa: Structures for Migrate On Fault per NUMA migration rate limiting
mm: numa: Migrate pages handled during a pmd_numa hinting fault
mm: numa: Migrate on reference policy
...
This reverts commit bd52276fa1 ("x86-64/efi: Use EFI to deal with
platform wall clock (again)"), and the two supporting commits:
da5a108d05b4: "x86/kernel: remove tboot 1:1 page table creation code"
185034e72d59: "x86, efi: 1:1 pagetable mapping for virtual EFI calls")
as they all depend semantically on commit 53b87cf088 ("x86, mm:
Include the entire kernel memory map in trampoline_pgd") that got
reverted earlier due to the problems it caused.
This was pointed out by Yinghai Lu, and verified by me on my Macbook Air
that uses EFI.
Pointed-out-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull x86 EFI update from Peter Anvin:
"EFI tree, from Matt Fleming. Most of the patches are the new efivarfs
filesystem by Matt Garrett & co. The balance are support for EFI
wallclock in the absence of a hardware-specific driver, and various
fixes and cleanups."
* 'core-efi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (24 commits)
efivarfs: Make efivarfs_fill_super() static
x86, efi: Check table header length in efi_bgrt_init()
efivarfs: Use query_variable_info() to limit kmalloc()
efivarfs: Fix return value of efivarfs_file_write()
efivarfs: Return a consistent error when efivarfs_get_inode() fails
efivarfs: Make 'datasize' unsigned long
efivarfs: Add unique magic number
efivarfs: Replace magic number with sizeof(attributes)
efivarfs: Return an error if we fail to read a variable
efi: Clarify GUID length calculations
efivarfs: Implement exclusive access for {get,set}_variable
efivarfs: efivarfs_fill_super() ensure we clean up correctly on error
efivarfs: efivarfs_fill_super() ensure we free our temporary name
efivarfs: efivarfs_fill_super() fix inode reference counts
efivarfs: efivarfs_create() ensure we drop our reference on inode on error
efivarfs: efivarfs_file_read ensure we free data in error paths
x86-64/efi: Use EFI to deal with platform wall clock (again)
x86/kernel: remove tboot 1:1 page table creation code
x86, efi: 1:1 pagetable mapping for virtual EFI calls
x86, mm: Include the entire kernel memory map in trampoline_pgd
...
N_HIGH_MEMORY stands for the nodes that has normal or high memory.
N_MEMORY stands for the nodes that has any memory.
The code here need to handle with the nodes which have memory, we should
use N_MEMORY instead.
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Signed-off-by: Wen Congyang <wency@cn.fujitsu.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Hillf Danton <dhillf@gmail.com>
Cc: Lin Feng <linfeng@cn.fujitsu.com>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds Kconfig options and kernel parameters to allow the
enabling and disabling of automatic NUMA balancing. The existance
of such a switch was and is very important when debugging problems
related to transparent hugepages and we should have the same for
automatic NUMA placement.
Signed-off-by: Mel Gorman <mgorman@suse.de>
Implement pte_numa and pmd_numa.
We must atomically set the numa bit and clear the present bit to
define a pte_numa or pmd_numa.
Once a pte or pmd has been set as pte_numa or pmd_numa, the next time
a thread touches a virtual address in the corresponding virtual range,
a NUMA hinting page fault will trigger. The NUMA hinting page fault
will clear the NUMA bit and set the present bit again to resolve the
page fault.
The expectation is that a NUMA hinting page fault is used as part
of a placement policy that decides if a page should remain on the
current node or migrated to a different node.
Acked-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Signed-off-by: Mel Gorman <mgorman@suse.de>
Conflicts:
arch/x86/kernel/ptrace.c
Pull the latest RCU tree from Paul E. McKenney:
" The major features of this series are:
1. A first version of no-callbacks CPUs. This version prohibits
offlining CPU 0, but only when enabled via CONFIG_RCU_NOCB_CPU=y.
Relaxing this constraint is in progress, but not yet ready
for prime time. These commits were posted to LKML at
https://lkml.org/lkml/2012/10/30/724, and are at branch rcu/nocb.
2. Changes to SRCU that allows statically initialized srcu_struct
structures. These commits were posted to LKML at
https://lkml.org/lkml/2012/10/30/296, and are at branch rcu/srcu.
3. Restructuring of RCU's debugfs output. These commits were posted
to LKML at https://lkml.org/lkml/2012/10/30/341, and are at
branch rcu/tracing.
4. Additional CPU-hotplug/RCU improvements, posted to LKML at
https://lkml.org/lkml/2012/10/30/327, and are at branch rcu/hotplug.
Note that the commit eliminating __stop_machine() was judged to
be too-high of risk, so is deferred to 3.9.
5. Changes to RCU's idle interface, most notably a new module
parameter that redirects normal grace-period operations to
their expedited equivalents. These were posted to LKML at
https://lkml.org/lkml/2012/10/30/739, and are at branch rcu/idle.
6. Additional diagnostics for RCU's CPU stall warning facility,
posted to LKML at https://lkml.org/lkml/2012/10/30/315, and
are at branch rcu/stall. The most notable change reduces the
default RCU CPU stall-warning time from 60 seconds to 21 seconds,
so that it once again happens sooner than the softlockup timeout.
7. Documentation updates, which were posted to LKML at
https://lkml.org/lkml/2012/10/30/280, and are at branch rcu/doc.
A couple of late-breaking changes were posted at
https://lkml.org/lkml/2012/11/16/634 and
https://lkml.org/lkml/2012/11/16/547.
8. Miscellaneous fixes, which were posted to LKML at
https://lkml.org/lkml/2012/10/30/309, along with a late-breaking
change posted at Fri, 16 Nov 2012 11:26:25 -0800 with message-ID
<20121116192625.GA447@linux.vnet.ibm.com>, but which lkml.org
seems to have missed. These are at branch rcu/fixes.
9. Finally, a fix for an lockdep-RCU splat was posted to LKML
at https://lkml.org/lkml/2012/11/7/486. This is at rcu/next. "
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Create a new subsystem that probes on kernel boundaries
to keep track of the transitions between level contexts
with two basic initial contexts: user or kernel.
This is an abstraction of some RCU code that use such tracking
to implement its userspace extended quiescent state.
We need to pull this up from RCU into this new level of indirection
because this tracking is also going to be used to implement an "on
demand" generic virtual cputime accounting. A necessary step to
shutdown the tick while still accounting the cputime.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Li Zhong <zhong@linux.vnet.ibm.com>
Cc: Gilad Ben-Yossef <gilad@benyossef.com>
Reviewed-by: Steven Rostedt <rostedt@goodmis.org>
[ paulmck: fix whitespace error and email address. ]
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
The MSDOS/MBR partition table includes a 32-bit unique ID, often referred
to as the NT disk signature. When combined with a partition number within
the table, this can form a unique ID similar in concept to EFI/GPT's
partition UUID. Constructing and recording this value in struct
partition_meta_info allows MSDOS partitions to be referred to on the
kernel command-line using the following syntax:
root=PARTUUID=0002dd75-01
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Will Drewry <wad@chromium.org>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Reduce the minimum length for a root=PARTUUID= parameter to be considered
valid from 36 to 1. EFI/GPT partition UUIDs are always exactly 36
characters long, hence the previous limit. However, the next patch will
support DOS/MBR UUIDs too, which have a different, shorter, format.
Instead of validating any particular length, just ensure that at least
some non-empty value was given by the user.
Also, consider a missing UUID value to be a parsing error, in the same
vein as if /PARTNROFF exists and can't be parsed. As such, make both
error cases print a message and disable rootwait. Convert to pr_err while
we're at it.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Will Drewry <wad@chromium.org>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This will allow other types of UUID to be stored here, aside from true
UUIDs. This also simplifies code that uses this field, since it's usually
constructed from a, used as a, or compared to other, strings.
Note: A simplistic approach here would be to set uuid_str[36]=0 whenever a
/PARTNROFF option was found to be present. However, this modifies the
input string, and causes subsequent calls to devt_from_partuuid() not to
see the /PARTNROFF option, which causes different results. In order to
avoid misleading future maintainers, this parameter is marked const.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Will Drewry <wad@chromium.org>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Assign a unique proc inode to each namespace, and use that
inode number to ensure we only allocate at most one proc
inode for every namespace in proc.
A single proc inode per namespace allows userspace to test
to see if two processes are in the same namespace.
This has been a long requested feature and only blocked because
a naive implementation would put the id in a global space and
would ultimately require having a namespace for the names of
namespaces, making migration and certain virtualization tricks
impossible.
We still don't have per superblock inode numbers for proc, which
appears necessary for application unaware checkpoint/restart and
migrations (if the application is using namespace file descriptors)
but that is now allowd by the design if it becomes important.
I have preallocated the ipc and uts initial proc inode numbers so
their structures can be statically initialized.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Instead of setting child_reaper and SIGNAL_UNKILLABLE one way
for the system init process, and another way for pid namespace
init processes test pid->nr == 1 and use the same code for both.
For the global init this results in SIGNAL_UNKILLABLE being set
much earlier in the initialization process.
This is a small cleanup and it paves the way for allowing unshare and
enter of the pid namespace as that path like our global init also will
not set CLONE_NEWPID.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
klogd is woken up asynchronously from the tick in order
to do it safely.
However if printk is called when the tick is stopped, the reader
won't be woken up until the next interrupt, which might not fire
for a while. As a result, the user may miss some message.
To fix this, lets implement the printk tick using a lazy irq work.
This subsystem takes care of the timer tick state and can
fix up accordingly.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
irq work can run on any arch even without IPI
support because of the hook on update_process_times().
So lets remove HAVE_IRQ_WORK because it doesn't reflect
any backend requirement.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
RCU callback execution can add significant OS jitter and also can
degrade both scheduling latency and, in asymmetric multiprocessors,
energy efficiency. This commit therefore adds the ability for selected
CPUs ("rcu_nocbs=" boot parameter) to have their callbacks offloaded
to kthreads. If the "rcu_nocb_poll" boot parameter is also specified,
these kthreads will do polling, removing the need for the offloaded
CPUs to do wakeups. At least one CPU must be doing normal callback
processing: currently CPU 0 cannot be selected as a no-CBs CPU.
In addition, attempts to offline the last normal-CBs CPU will fail.
This feature was inspired by Jim Houston's and Joe Korty's JRCU, and
this commit includes fixes to problems located by Fengguang Wu's
kbuild test robot.
[ paulmck: Added gfp.h include file as suggested by Fengguang Wu. ]
Signed-off-by: Paul E. McKenney <paul.mckenney@linaro.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Use kuid_t and kgid_t in struct fuse_conn and struct fuse_mount_data.
The connection between between a fuse filesystem and a fuse daemon is
established when a fuse filesystem is mounted and provided with a file
descriptor the fuse daemon created by opening /dev/fuse.
For now restrict the communication of uids and gids between the fuse
filesystem and the fuse daemon to the initial user namespace. Enforce
this by verifying the file descriptor passed to the mount of fuse was
opened in the initial user namespace. Ensuring the mount happens in
the initial user namespace is not necessary as mounts from non-initial
user namespaces are not yet allowed.
In fuse_req_init_context convert the currrent fsuid and fsgid into the
initial user namespace for the request that will be sent to the fuse
daemon.
In fuse_fill_attr convert the uid and gid passed from the fuse daemon
from the initial user namespace into kuids and kgids.
In iattr_to_fattr called from fuse_setattr convert kuids and kgids
into the uids and gids in the initial user namespace before passing
them to the fuse filesystem.
In fuse_change_attributes_common called from fuse_dentry_revalidate,
fuse_permission, fuse_geattr, and fuse_setattr, and fuse_iget convert
the uid and gid from the fuse daemon into a kuid and a kgid to store
on the fuse inode.
By default fuse mounts are restricted to task whose uid, suid, and
euid matches the fuse user_id and whose gid, sgid, and egid matches
the fuse group id. Convert the user_id and group_id mount options
into kuids and kgids at mount time, and use uid_eq and gid_eq to
compare the in fuse_allow_task.
Cc: Miklos Szeredi <miklos@szeredi.hu>
Acked-by: Serge Hallyn <serge.hallyn@canonical.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Use kuid_t and kgid_t in struct autofs_info and struct autofs_wait_queue.
When creating directories and symlinks default the uid and gid of
the mount requester to the global root uid and gid. autofs4_wait
will update these fields when a mount is requested.
When generating autofsv5 packets report the uid and gid of the mount
requestor in user namespace of the process that opened the pipe,
reporting unmapped uids and gids as overflowuid and overflowgid.
In autofs_dev_ioctl_requester return the uid and gid of the last mount
requester converted into the calling processes user namespace. When the
uid or gid don't map return overflowuid and overflowgid as appropriate,
allowing failure to find a mount requester to be distinguished from
failure to map a mount requester.
The uid and gid mount options specifying the user and group of the
root autofs inode are converted into kuid and kgid as they are parsed
defaulting to the current uid and current gid of the process that
mounts autofs.
Mounting of autofs for the present remains confined to processes in
the initial user namespace.
Cc: Ian Kent <raven@themaw.net>
Acked-by: Serge Hallyn <serge.hallyn@canonical.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
gcc-4.1.2 inlines weak functions, which causes FRV to fail when the dummy
thread_info_cache_init() gets inlined into start_kernel().
Signed-off-by: David Howells <dhowells@redhat.com>
Other than ix86, x86-64 on EFI so far didn't set the
{g,s}et_wallclock accessors to the EFI routines, thus
incorrectly using raw RTC accesses instead.
Simply removing the #ifdef around the respective code isn't
enough, however: While so far early get-time calls were done in
physical mode, this doesn't work properly for x86-64, as virtual
addresses would still need to be set up for all runtime regions
(which wasn't the case on the system I have access to), so
instead the patch moves the call to efi_enter_virtual_mode()
ahead (which in turn allows to drop all code related to calling
efi-get-time in physical mode).
Additionally the earlier calling of efi_set_executable()
requires the CPA code to cope, i.e. during early boot it must be
avoided to call cpa_flush_array(), as the first thing this
function does is a BUG_ON(irqs_disabled()).
Also make the two EFI functions in question here static -
they're not being referenced elsewhere.
History:
This commit was originally merged as bacef661ac ("x86-64/efi:
Use EFI to deal with platform wall clock") but it resulted in some
ASUS machines no longer booting due to a firmware bug, and so was
reverted in f026cfa82f. A pre-emptive fix for the buggy ASUS
firmware was merged in 03a1c254975e ("x86, efi: 1:1 pagetable
mapping for virtual EFI calls") so now this patch can be
reapplied.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Tested-by: Matt Fleming <matt.fleming@intel.com>
Acked-by: Matthew Garrett <mjg@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com> [added commit history]
This commit adds a "try" missing from the end of the first paragraph
of the RCU_USER_QS help text.
[ paulmck: Also fix up the last paragraph a bit. ]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
The RCU_FAST_NO_HZ help text included a warning about overhead on large
systems, but that issue has since been resolved. The main remaining
issue with RCU_FAST_NO_HZ is increased real-time latency. This commit
therefore updates the help text accordingly.
Signed-off-by: Paul E. McKenney <paul.mckenney@linaro.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Pull module signing support from Rusty Russell:
"module signing is the highlight, but it's an all-over David Howells frenzy..."
Hmm "Magrathea: Glacier signing key". Somebody has been reading too much HHGTTG.
* 'modules-next' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux: (37 commits)
X.509: Fix indefinite length element skip error handling
X.509: Convert some printk calls to pr_devel
asymmetric keys: fix printk format warning
MODSIGN: Fix 32-bit overflow in X.509 certificate validity date checking
MODSIGN: Make mrproper should remove generated files.
MODSIGN: Use utf8 strings in signer's name in autogenerated X.509 certs
MODSIGN: Use the same digest for the autogen key sig as for the module sig
MODSIGN: Sign modules during the build process
MODSIGN: Provide a script for generating a key ID from an X.509 cert
MODSIGN: Implement module signature checking
MODSIGN: Provide module signing public keys to the kernel
MODSIGN: Automatically generate module signing keys if missing
MODSIGN: Provide Kconfig options
MODSIGN: Provide gitignore and make clean rules for extra files
MODSIGN: Add FIPS policy
module: signature checking hook
X.509: Add a crypto key parser for binary (DER) X.509 certificates
MPILIB: Provide a function to read raw data into an MPI
X.509: Add an ASN.1 decoder
X.509: Add simple ASN.1 grammar compiler
...
Pull third pile of kernel_execve() patches from Al Viro:
"The last bits of infrastructure for kernel_thread() et.al., with
alpha/arm/x86 use of those. Plus sanitizing the asm glue and
do_notify_resume() on alpha, fixing the "disabled irq while running
task_work stuff" breakage there.
At that point the rest of kernel_thread/kernel_execve/sys_execve work
can be done independently for different architectures. The only
pending bits that do depend on having all architectures converted are
restrictred to fs/* and kernel/* - that'll obviously have to wait for
the next cycle.
I thought we'd have to wait for all of them done before we start
eliminating the longjump-style insanity in kernel_execve(), but it
turned out there's a very simple way to do that without flagday-style
changes."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/signal:
alpha: switch to saner kernel_execve() semantics
arm: switch to saner kernel_execve() semantics
x86, um: convert to saner kernel_execve() semantics
infrastructure for saner ret_from_kernel_thread semantics
make sure that kernel_thread() callbacks call do_exit() themselves
make sure that we always have a return path from kernel_execve()
ppc: eeh_event should just use kthread_run()
don't bother with kernel_thread/kernel_execve for launching linuxrc
alpha: get rid of switch_stack argument of do_work_pending()
alpha: don't bother passing switch_stack separately from regs
alpha: take SIGPENDING/NOTIFY_RESUME loop into signal.c
alpha: simplify TIF_NEED_RESCHED handling
Pull third pile of VFS updates from Al Viro:
"Stuff from Jeff Layton, mostly. Sanitizing interplay between audit
and namei, removing a lot of insanity from audit_inode() mess and
getting things ready for his ESTALE patchset."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
procfs: don't need a PATH_MAX allocation to hold a string representation of an int
vfs: embed struct filename inside of names_cache allocation if possible
audit: make audit_inode take struct filename
vfs: make path_openat take a struct filename pointer
vfs: turn do_path_lookup into wrapper around struct filename variant
audit: allow audit code to satisfy getname requests from its names_list
vfs: define struct filename and have getname() return it
vfs: unexport getname and putname symbols
acct: constify the name arg to acct_on
vfs: allocate page instead of names_cache buffer in mount_block_root
audit: overhaul __audit_inode_child to accomodate retrying
audit: optimize audit_compare_dname_path
audit: make audit_compare_dname_path use parent_len helper
audit: remove dirlen argument to audit_compare_dname_path
audit: set the name_len in audit_inode for parent lookups
audit: add a new "type" field to audit_names struct
audit: reverse arguments to audit_inode_child
audit: no need to walk list in audit_inode if name is NULL
audit: pass in dentry to audit_copy_inode wherever possible
audit: remove unnecessary NULL ptr checks from do_path_lookup
* allow kernel_execve() leave the actual return to userland to
caller (selected by CONFIG_GENERIC_KERNEL_EXECVE). Callers
updated accordingly.
* architecture that does select GENERIC_KERNEL_EXECVE in its
Kconfig should have its ret_from_kernel_thread() do this:
call schedule_tail
call the callback left for it by copy_thread(); if it ever
returns, that's because it has just done successful kernel_execve()
jump to return from syscall
IOW, its only difference from ret_from_fork() is that it does call the
callback.
* such an architecture should also get rid of ret_from_kernel_execve()
and __ARCH_WANT_KERNEL_EXECVE
This is the last part of infrastructure patches in that area - from
that point on work on different architectures can live independently.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Pull RCU fixes from Ingo Molnar:
"This tree includes a shutdown/cpu-hotplug deadlock fix and a
documentation fix."
* 'core-rcu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
rcu: Advise most users not to enable RCU user mode
rcu: Grace-period initialization excludes only RCU notifier
First, it's incorrect to call putname() after __getname_gfp() since the
bare __getname_gfp() call skips the auditing code, while putname()
doesn't.
mount_block_root allocates a PATH_MAX buffer via __getname_gfp, and then
calls get_fs_names to fill the buffer. That function can call
get_filesystem_list which assumes that that buffer is a full page in
size. On arches where PAGE_SIZE != 4k, then this could potentially
overrun.
In practice, it's hard to imagine the list of filesystem names even
approaching 4k, but it's best to be safe. Just allocate a page for this
purpose instead.
With this, we can also remove the __getname_gfp() definition since there
are no more callers.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The only place where kernel_execve() is called without a way to
return to the caller of kernel_thread() callback is kernel_post().
Reorganize kernel_init()/kernel_post() - instead of the former
calling the latter in the end (and getting freed by it), have the
latter *begin* with calling the former (and turn the latter into
kernel_thread() callback, of course).
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Discourage distros from enabling CONFIG_RCU_USER_QS
because it brings overhead for no benefits yet.
It's not a useful feature on its own until we can
fully run an adaptive tickless kernel.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Check the signature on the module against the keys compiled into the kernel or
available in a hardware key store.
Currently, only RSA keys are supported - though that's easy enough to change,
and the signature is expected to contain raw components (so not a PGP or
PKCS#7 formatted blob).
The signature blob is expected to consist of the following pieces in order:
(1) The binary identifier for the key. This is expected to match the
SubjectKeyIdentifier from an X.509 certificate. Only X.509 type
identifiers are currently supported.
(2) The signature data, consisting of a series of MPIs in which each is in
the format of a 2-byte BE word sizes followed by the content data.
(3) A 12 byte information block of the form:
struct module_signature {
enum pkey_algo algo : 8;
enum pkey_hash_algo hash : 8;
enum pkey_id_type id_type : 8;
u8 __pad;
__be32 id_length;
__be32 sig_length;
};
The three enums are defined in crypto/public_key.h.
'algo' contains the public-key algorithm identifier (0->DSA, 1->RSA).
'hash' contains the digest algorithm identifier (0->MD4, 1->MD5, 2->SHA1,
etc.).
'id_type' contains the public-key identifier type (0->PGP, 1->X.509).
'__pad' should be 0.
'id_length' should contain in the binary identifier length in BE form.
'sig_length' should contain in the signature data length in BE form.
The lengths are in BE order rather than CPU order to make dealing with
cross-compilation easier.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> (minor Kconfig fix)
Provide kernel configuration options for module signing.
The following configuration options are added:
CONFIG_MODULE_SIG_SHA1
CONFIG_MODULE_SIG_SHA224
CONFIG_MODULE_SIG_SHA256
CONFIG_MODULE_SIG_SHA384
CONFIG_MODULE_SIG_SHA512
These select the cryptographic hash used to digest the data prior to signing.
Additionally, the crypto module selected will be built into the kernel as it
won't be possible to load it as a module without incurring a circular
dependency when the kernel tries to check its signature.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
We do a very simple search for a particular string appended to the module
(which is cache-hot and about to be SHA'd anyway). There's both a config
option and a boot parameter which control whether we accept or fail with
unsigned modules and modules that are signed with an unknown key.
If module signing is enabled, the kernel will be tainted if a module is
loaded that is unsigned or has a signature for which we don't have the
key.
(Useful feedback and tweaks by David Howells <dhowells@redhat.com>)
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
After both prio_tree users have been converted to use red-black trees,
there is no need to keep around the prio tree library anymore.
Signed-off-by: Michel Lespinasse <walken@google.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Hillf Danton <dhillf@gmail.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Introduce SYSCTL_EXCEPTION_TRACE config option and selec it in the
architectures requiring support for the "exception-trace" debug_table
entry in kernel/sysctl.c.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Introduce HAVE_UID16 config option and select it in corresponding
architecture Kconfig files. UID16 now only depends on HAVE_UID16.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a simple ASN.1 grammar compiler. This produces a bytecode output that can
be fed to a decoder to inform the decoder how to interpret the ASN.1 stream it
is trying to parse.
Action functions can be specified in the grammar by interpolating:
({ foo })
after a type, for example:
SubjectPublicKeyInfo ::= SEQUENCE {
algorithm AlgorithmIdentifier,
subjectPublicKey BIT STRING ({ do_key_data })
}
The decoder is expected to call these after matching this type and parsing the
contents if it is a constructed type.
The grammar compiler does not currently support the SET type (though it does
support SET OF) as I can't see a good way of tracking which members have been
encountered yet without using up extra stack space.
Currently, the grammar compiler will fail if more than 256 bytes of bytecode
would be produced or more than 256 actions have been specified as it uses
8-bit jump values and action indices to keep space usage down.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Adds an expert Kconfig option, CONFIG_COREDUMP, which allows disabling of
core dump. This saves approximately 2.6k in the compiled kernel, and
complements CONFIG_ELF_CORE, which now depends on it.
CONFIG_COREDUMP also disables coredump-related sysctls, except for
suid_dumpable and related functions, which are necessary for ptrace.
[akpm@linux-foundation.org: fix binfmt_aout.c build]
Signed-off-by: Alex Kelly <alex.page.kelly@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Acked-by: Serge Hallyn <serge.hallyn@canonical.com>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The PA-RISC tool chain seems to have some problem with correct
read/write attributes on sections. This causes problems when the const
sections are fixed up for other architecture to only contain truly
read-only data.
Disable const sections for PA-RISC
This can cause a bit of noise with modpost.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Helge Deller <deller@gmx.de>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull user namespace changes from Eric Biederman:
"This is a mostly modest set of changes to enable basic user namespace
support. This allows the code to code to compile with user namespaces
enabled and removes the assumption there is only the initial user
namespace. Everything is converted except for the most complex of the
filesystems: autofs4, 9p, afs, ceph, cifs, coda, fuse, gfs2, ncpfs,
nfs, ocfs2 and xfs as those patches need a bit more review.
The strategy is to push kuid_t and kgid_t values are far down into
subsystems and filesystems as reasonable. Leaving the make_kuid and
from_kuid operations to happen at the edge of userspace, as the values
come off the disk, and as the values come in from the network.
Letting compile type incompatible compile errors (present when user
namespaces are enabled) guide me to find the issues.
The most tricky areas have been the places where we had an implicit
union of uid and gid values and were storing them in an unsigned int.
Those places were converted into explicit unions. I made certain to
handle those places with simple trivial patches.
Out of that work I discovered we have generic interfaces for storing
quota by projid. I had never heard of the project identifiers before.
Adding full user namespace support for project identifiers accounts
for most of the code size growth in my git tree.
Ultimately there will be work to relax privlige checks from
"capable(FOO)" to "ns_capable(user_ns, FOO)" where it is safe allowing
root in a user names to do those things that today we only forbid to
non-root users because it will confuse suid root applications.
While I was pushing kuid_t and kgid_t changes deep into the audit code
I made a few other cleanups. I capitalized on the fact we process
netlink messages in the context of the message sender. I removed
usage of NETLINK_CRED, and started directly using current->tty.
Some of these patches have also made it into maintainer trees, with no
problems from identical code from different trees showing up in
linux-next.
After reading through all of this code I feel like I might be able to
win a game of kernel trivial pursuit."
Fix up some fairly trivial conflicts in netfilter uid/git logging code.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace: (107 commits)
userns: Convert the ufs filesystem to use kuid/kgid where appropriate
userns: Convert the udf filesystem to use kuid/kgid where appropriate
userns: Convert ubifs to use kuid/kgid
userns: Convert squashfs to use kuid/kgid where appropriate
userns: Convert reiserfs to use kuid and kgid where appropriate
userns: Convert jfs to use kuid/kgid where appropriate
userns: Convert jffs2 to use kuid and kgid where appropriate
userns: Convert hpfs to use kuid and kgid where appropriate
userns: Convert btrfs to use kuid/kgid where appropriate
userns: Convert bfs to use kuid/kgid where appropriate
userns: Convert affs to use kuid/kgid wherwe appropriate
userns: On alpha modify linux_to_osf_stat to use convert from kuids and kgids
userns: On ia64 deal with current_uid and current_gid being kuid and kgid
userns: On ppc convert current_uid from a kuid before printing.
userns: Convert s390 getting uid and gid system calls to use kuid and kgid
userns: Convert s390 hypfs to use kuid and kgid where appropriate
userns: Convert binder ipc to use kuids
userns: Teach security_path_chown to take kuids and kgids
userns: Add user namespace support to IMA
userns: Convert EVM to deal with kuids and kgids in it's hmac computation
...
Here is the big driver core update for 3.7-rc1.
A number of firmware_class.c updates (as you saw a month or so ago), and
some hyper-v updates and some printk fixes as well. All patches that
are outside of the drivers/base area have been acked by the respective
maintainers, and have all been in the linux-next tree for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlBp3vkACgkQMUfUDdst+ylQoACgldktGFgkCLzH+rGYthrXOC5P
9hUAnjmOhdoHlMTL81vWTlH+BrGernym
=khrr
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core merge from Greg Kroah-Hartman:
"Here is the big driver core update for 3.7-rc1.
A number of firmware_class.c updates (as you saw a month or so ago),
and some hyper-v updates and some printk fixes as well. All patches
that are outside of the drivers/base area have been acked by the
respective maintainers, and have all been in the linux-next tree for a
while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'driver-core-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (95 commits)
memory: tegra{20,30}-mc: Fix reading incorrect register in mc_readl()
device.h: Add missing inline to #ifndef CONFIG_PRINTK dev_vprintk_emit
memory: emif: Add ifdef CONFIG_DEBUG_FS guard for emif_debugfs_[init|exit]
Documentation: Fixes some translation error in Documentation/zh_CN/gpio.txt
Documentation: Remove 3 byte redundant code at the head of the Documentation/zh_CN/arm/booting
Documentation: Chinese translation of Documentation/video4linux/omap3isp.txt
device and dynamic_debug: Use dev_vprintk_emit and dev_printk_emit
dev: Add dev_vprintk_emit and dev_printk_emit
netdev_printk/netif_printk: Remove a superfluous logging colon
netdev_printk/dynamic_netdev_dbg: Directly call printk_emit
dev_dbg/dynamic_debug: Update to use printk_emit, optimize stack
driver-core: Shut up dev_dbg_reatelimited() without DEBUG
tools/hv: Parse /etc/os-release
tools/hv: Check for read/write errors
tools/hv: Fix exit() error code
tools/hv: Fix file handle leak
Tools: hv: Implement the KVP verb - KVP_OP_GET_IP_INFO
Tools: hv: Rename the function kvp_get_ip_address()
Tools: hv: Implement the KVP verb - KVP_OP_SET_IP_INFO
Tools: hv: Add an example script to configure an interface
...
Features currently supported:
- 39-bit address space for user and kernel (each)
- 4KB and 64KB page configurations
- Compat (32-bit) user applications (ARMv7, EABI only)
- Flattened Device Tree (mandated for all AArch64 platforms)
- ARM generic timers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.9 (GNU/Linux)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=buJB
-----END PGP SIGNATURE-----
Merge tag 'arm64-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cmarinas/linux-aarch64
Pull arm64 support from Catalin Marinas:
"Linux support for the 64-bit ARM architecture (AArch64)
Features currently supported:
- 39-bit address space for user and kernel (each)
- 4KB and 64KB page configurations
- Compat (32-bit) user applications (ARMv7, EABI only)
- Flattened Device Tree (mandated for all AArch64 platforms)
- ARM generic timers"
* tag 'arm64-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cmarinas/linux-aarch64: (35 commits)
arm64: ptrace: remove obsolete ptrace request numbers from user headers
arm64: Do not set the SMP/nAMP processor bit
arm64: MAINTAINERS update
arm64: Build infrastructure
arm64: Miscellaneous header files
arm64: Generic timers support
arm64: Loadable modules
arm64: Miscellaneous library functions
arm64: Performance counters support
arm64: Add support for /proc/sys/debug/exception-trace
arm64: Debugging support
arm64: Floating point and SIMD
arm64: 32-bit (compat) applications support
arm64: User access library functions
arm64: Signal handling support
arm64: VDSO support
arm64: System calls handling
arm64: ELF definitions
arm64: SMP support
arm64: DMA mapping API
...
Pull x86/EFI changes from Ingo Molnar:
"EFI loader robustness enhancements plus smaller fixes"
* 'x86-efi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
efi: Fix the ACPI BGRT driver for images located in EFI boot services memory
efi: Add a function to look up existing IO memory mappings
efi: Defer freeing boot services memory until after ACPI init
x86, EFI: Calculate the EFI framebuffer size instead of trusting the firmware
efifb: Skip DMI checks if the bootloader knows what it's doing
efi: initialize efi.runtime_version to make query_variable_info/update_capsule workable
efi: Build EFI stub with EFI-appropriate options
X86: Improve GOP detection in the EFI boot stub
Pull scheduler changes from Ingo Molnar:
"Continued quest to clean up and enhance the cputime code by Frederic
Weisbecker, in preparation for future tickless kernel features.
Other than that, smallish changes."
Fix up trivial conflicts due to additions next to each other in arch/{x86/}Kconfig
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (24 commits)
cputime: Make finegrained irqtime accounting generally available
cputime: Gather time/stats accounting config options into a single menu
ia64: Reuse system and user vtime accounting functions on task switch
ia64: Consolidate user vtime accounting
vtime: Consolidate system/idle context detection
cputime: Use a proper subsystem naming for vtime related APIs
sched: cpu_power: enable ARCH_POWER
sched/nohz: Clean up select_nohz_load_balancer()
sched: Fix load avg vs. cpu-hotplug
sched: Remove __ARCH_WANT_INTERRUPTS_ON_CTXSW
sched: Fix nohz_idle_balance()
sched: Remove useless code in yield_to()
sched: Add time unit suffix to sched sysctl knobs
sched/debug: Limit sd->*_idx range on sysctl
sched: Remove AFFINE_WAKEUPS feature flag
s390: Remove leftover account_tick_vtime() header
cputime: Consolidate vtime handling on context switch
sched: Move cputime code to its own file
cputime: Generalize CONFIG_VIRT_CPU_ACCOUNTING
tile: Remove SD_PREFER_LOCAL leftover
...
The ACPI BGRT driver accesses the BIOS logo image when it initializes.
However, ACPI 5.0 (which introduces the BGRT) recommends putting the
logo image in EFI boot services memory, so that the OS can reclaim that
memory. Production systems follow this recommendation, breaking the
ACPI BGRT driver.
Move the bulk of the BGRT code to run during a new EFI late
initialization phase, which occurs after switching EFI to virtual mode,
and after initializing ACPI, but before freeing boot services memory.
Copy the BIOS logo image to kernel memory at that point, and make it
accessible to the BGRT driver. Rework the existing ACPI BGRT driver to
act as a simple wrapper exposing that image (and the properties from the
BGRT) via sysfs.
Signed-off-by: Josh Triplett <josh@joshtriplett.org>
Link: http://lkml.kernel.org/r/93ce9f823f1c1f3bb88bdd662cce08eee7a17f5d.1348876882.git.josh@joshtriplett.org
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Provide a config option that enables the userspace
RCU extended quiescent state on every CPUs by default.
This is for testing purpose.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Alessio Igor Bogani <abogani@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Avi Kivity <avi@redhat.com>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Geoff Levand <geoff@infradead.org>
Cc: Gilad Ben Yossef <gilad@benyossef.com>
Cc: Hakan Akkan <hakanakkan@gmail.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Josh Triplett <josh@joshtriplett.org>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Max Krasnyansky <maxk@qualcomm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephen Hemminger <shemminger@vyatta.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Sven-Thorsten Dietrich <thebigcorporation@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Luis R. Rodriguez
Paul E. McKenney
Peter De Schrijver
Linus Torvalds
Andrew Morton
Oleg Nesterov
Prarit Bhargava
Borislav Petkov
Fabian Frederick
Konstantin Khlebnikov
Vladimir Davydov
H. Peter Anvin
Andi Kleen
H. Peter Anvin
Rusty Russell
Peter Foley
Daniel M. Weeks
Josh Triplett
chishanmingshen
AKASHI Takahiro
蔡正龙
Rafael J. Wysocki
Heiko Carstens
Tejun Heo
Kang Hu
Al Viro
Tetsuo Handa
Geert Uytterhoeven
Santosh Shilimkar
Kirill A. Shutemov
Lee, Chun-Yi
Ingo Molnar
Peter Zijlstra
Paul Gortmaker
Eric W. Biederman
P J P
Christian Ruppert
Michael Opdenacker
P J P
Sebastian Capella
Helge Deller
Eric Paris
Krzysztof Mazur
David S. Miller
Hannes Frederic Sowa
Kevin Hilman
David Howells
Theodore Ts'o
Rob Landley
Michal Hocko
James Hogan
Yann E. MORIN
Dwight Engen
Frederic Weisbecker
Uwe Kleine-König
Kyungsik Lee
Joonsoo Kim
Thomas Gleixner
Toralf Förster
Steven Rostedt
Sergey Dyasly
Jiri Slaby
Greg Kroah-Hartman
Stephen Boyd
Stephen Rothwell
Stephane Eranian
Mike Frysinger
Lucas De Marchi
Richard Weinberger
Paul E. McKenney
Kees Cook
Vineet Gupta
Clark Williams
Michał Mirosław
Matt Fleming
Michal Marek
Kirill Smelkov
Vineet Gupta
Glauber Costa
Lai Jiangshan
Mel Gorman
Andrea Arcangeli
Stephen Warren
Jan Beulich
Jeff Layton
Michel Lespinasse
Catalin Marinas
Alex Kelly