As we just need a temporary array whilst performing the relocations for
the execbuffer, first attempt to allocate using kmalloc even if it is
not of order page-0. This avoids the overhead of remapping the
discontiguous array and so gives a moderate boost to execution
throughput.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Seems like we are forever to be cursed with buggy firmware, so allow the
user to explicitly set the panel connection status.
Of secondary utility for cases where I run laptops with the lid closed,
but still want to configure the LVDS.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Dave Airlie spotted that we had a potential bug should we ever rearrange
the drm_i915_gem_object so not the base drm_gem_object was not its first
member. He noticed that we often convert the return of
drm_gem_object_lookup() immediately into drm_i915_gem_object and then
check the result for nullity. This is only valid when the base object is
the first member and so the superobject has the same address. Play safe
instead and use the compiler to convert back to the original return
address for sanity testing.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
In a few places I replaced reads of per-pipe registers with the actual
register offsets themselves (converting I915_READ(reg) to _PIPE(reg)).
Alexey caught this on his 9xx machine because the cursor control write
was affected. A quick audit showed a few more places where I'd borked
a read, so here's a patch to fix things up.
Reported-by: Alexey Fisher <bug-track@fisher-privat.net>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[ickle: compilation fix]
Tested-by: Alexey Fisher <bug-track@fisher-privat.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This reverts commit 633f2ea266 and the
attempted fix dcbe6f2b3d.
There is a single clock source used for both SSC (some LVDS and DP) and
non-SSC (VGA, DVI) outputs. So we need to be careful to only enable SSC
as necessary. However, fiddling with DREFCLK was causing DP links to be
dropped and we do not have a fix ready, so revert.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Grab the latest stabilisation bits from -fixes and some suspend and
resume fixes from linus.
Conflicts:
drivers/gpu/drm/i915/i915_drv.h
drivers/gpu/drm/i915/i915_irq.c
Share the lid detection code for the all panels for consistent behaviour
and a single place to add the eventual quirks for crap hardware.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
We can enable some safely, but FDI and transcoder interrupts can occur
and block other interrupts from being detected (like port hotplug
events). So keep them disabled by default (they can be re-enabled for
debugging display bringup, but should generally be off).
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
If the gpu is hung, then whatever was inside the render cache is lost
and there is little point waiting for it. Or complaining if we see an
EIO or EAGAIN instead. So, if the GPU is indeed in its death throes when
we need to rewrite the registers for a new framebuffer, just ignore the
error and proceed with the update.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Disable any PCH ports associated with a pipe when disabling it. This
should prevent transcoder disable failures due to ports still being on.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[ickle: introduce *_PIPE_ENABLED() macro]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
... so we handle that for i915_gem_fault() in the same manner as
ERESTARTSYS, or we send a SIGBUS to the faulting application.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The irony of the patch to fix the resume regression on PineView causing
a further regression on Ironlake is not lost on me.
Reported-by: Jeff Chua <jeff.chua.linux@gmail.com>
Reported-by: Björn Schließmann <chronoss@gmx.de>
Tested-by: Björn Schließmann <chronoss@gmx.de>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=28802
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The documentation recommends that we should use a polling method for TV
detection as this is more power efficient than the interrupt based
mechanism (as the encoder can be completely switched off). A secondary
effect is that leaving the hotplug enabled seems to be causing pipe
underruns as reported by Hugh Dickins on his Crestline.
Tested-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[This is a candidate for stable, but needs minor porting to 2.6.37]
If the user changes the force-audio property and it no longer reflects
the current configuration, then we need to trigger a mode set in order
to update the registers.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
If we have an EDID for a digital panel, but we are probing a non-TMDS
connector then we know that this is a false detection, and vice versa.
This should reduce the number of bogus outputs on multi-function
adapters that report the same output on multiple connectors.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=34101
Reported-by: Sebastien Caty <sebastien.caty@mrnf.gouv.qc.ca>
Tested-by: Sebastien Caty <sebastien.caty@mrnf.gouv.qc.ca>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
The automatic powersaving feature is once again causing havoc, with 100%
reliable hangs on boot and resume on affected machines.
Reported-by: Francesco Allertsen <fallertsen@gmail.com>
Reported-by: Gui Rui <chaos.proton@gmail.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=28582
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
We had some conversions over to the _PIPE macros, but didn't get
everything. So hide the per-pipe regs with an _ (still used in a few
places for legacy) and add a few _PIPE based macros, then make sure
everyone uses them.
[update: remove usage of non-existent no-op macro]
[update 2: keep modesetting suspend/resume code, update to new reg names]
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[ickle: stylistic cleanups for checkpatch and taste]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
A lot of minor tweaks to fix the tracepoints, improve the outputting for
ftrace, and to generally make the tracepoints useful again. It is a start
and enough to begin identifying performance issues and gaps in our
coverage.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
By returning EAGAIN upon a wedged GPU before attempting to wait, we
would hit an infinite loop of repeating operation without ever
progressing. Instead this needs to be EIO so that userspace knows that
the GPU is truly wedged and not in the process of error recovery.
Similarly, we need to handle the error recovery during i915_gem_fault.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The PCH can drive several reference clocks simultaneously, and needs to
with multiple display configurations. So we can't just clobber the
existing state everytime we set a mode, we need to take into account
what the other CRTCs are doing at the time.
Doing so fixes an issue where you'd lose the LVDS display at boot if you
had an LVDS+DP config.
[updated: init bools and check CRTC status correctly]
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
When a transcoder is disabled, any ports pointing at it should also be
disabled. If they're not, we may fail to disable the transcoder,
leading to blank displays.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
These bits have a different meaning on ILK+, where planes are hardwired
to pipes. Fixing this avoid some spurious assertion failures.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Early chipsets (gen2/3) used function 1 as a placeholder for multi-head.
We used to ignore these since they were not assigned to
PCI_CLASS_DISPLAY_VGA. However with 934f992c7 we attempt to bind to all
Intel PCI_CLASS_DISPLAY devices (and functions) to work in multi-gpu
systems. This fails hard on gen2/3.
Reported-by: Ferenc Wágner <wferi@niif.hu>
Tested-by: Ferenc Wágner <wferi@niif.hu>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=28012
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
With the recent SDVO fix, this is working on all the machines I have to
hand - except for an 845G.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Judging by comments in the BIOS, if the SDVO LVDS option h40 is enabled,
then we are supposed to query the real panel type via Int15. We don't do
this and so for the Sony Vaio VGC-JS210J which has otherwise default
values, we choose the wrong mode.
This patch adds a driver option, i915.vbt_sdvo_panel_type, which can be
used to override the value in the VBT.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=33691
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Hugh Dickins found that characters in xterm were going missing and oft
delayed. Being the curious type, he managed to associate this with the
new high-precision vblank patches; disabling these he found, restored
the orderliness of his characters.
The oddness begins when one realised that Hugh was not using vblanks at
all on his system (fvwm and some xterms). Instead, all he had to go on
were warning of a pipe underrun, curiously enough at around 60Hz. He
poked and found that in addition to the underrun warning, the hardware
was flagging the start of a new frame, a vblank, which in turn was
kicking off the pending vblank processing code.
There is little we can do for the underruns on Hugh's machine, a
Crestline [965GM], which must have its FIFO watermarks set to 8.
However, we do not need to process the vblank if we know that they are
disabled...
Reported-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Instead of reporting EIO upfront in the entrance of an ioctl that may or
may not attempt to use the GPU, defer the actual detection of an invalid
ioctl to when we issue a GPU instruction. This allows us to continue to
use bo in video memory (via pread/pwrite and mmap) after the GPU has hung.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Based on a patch by Takashi Iwai.
Reported-by: Matthias Hopf <mat@mshopf.de>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=27272
Tested-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Upon resume, like after a cold boot, we need to forcibly probe the
analog connector and cannot rely on the hotplug status.
Based on a patch by Takashi Iwai.
Reported-by: Stefan Dirsch <sndirsch@suse.de>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=26952
Tested-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Call drm_mode_config_reset() after an invalidation event to restore any
cached state to unknown.
Tested-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
We were not pausing after detecting the response was pending and so did
not allow the hardware sufficient time to complete before aborting. This
lead to transient failures whilst probing SDVO devices.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=30235
Reported-by: Knut Petersen <Knut_Petersen@t-online.de>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Rather than power cycling the panel when there are no bits to display,
use the VDD AUX bit to power the panel up just enough for DP AUX
transactions to work. This prevents a bit of unnecessary ugliness as
mode sets occur on the panel.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Now that we're doing the right thing elsewhere, these are no longer
necessary.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=31114
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Move the plane->mode config to the point of use rather than repeatedly
querying the same information.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
error_bo and pinned_bo could be used uninitialised if there were no
active buffers.
Caught by kmemcheck.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Chris Wilson
Jesse Barnes
Eric Anholt