If DEBUG_LL and earlyprintk are enabled, and omap-serial.c is compiled
as a module, the kernel boot hangs early as the clocks for serial port
are cut while earlyprintk still uses the port.
The problem is a race between the late_initcall for omap_device (which
idles devices that have no drivers) and the late_initcall in
kernel/printk.c which turns off the earlyconsole. Any printks
that happen between this omap_device late initcall and the earlyconsole
late initcall will crash when accessing the UART.
The fix is to ensure the omap_device initcall happens after the
earlyconsole initcall.
Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 9fdca9df (spi: omap2-mcspi: convert to module_platform_driver)
broke the SPI display/panel driver probe on RX-51/N900. The exact cause is
not fully understood, but it seems to be related to the probe order. SPI
communication to the panel driver (spi1.2) fails unless the touchscreen
(spi1.0) has been probed/initialized before. When the omap2-mcspi driver
was converted to a platform driver, it resulted in that the devices are
probed immediately after the board registers them in the order they are
listed in the board file.
Fix the issue by moving the touchscreen before the panel in the SPI
device list.
The patch fixes the following failure:
[ 1.260955] acx565akm spi1.2: invalid display ID
[ 1.265899] panel-acx565akm display0: acx_panel_probe panel detect error
[ 1.273071] omapdss CORE error: driver probe failed: -19
Tested-by: Sebastian Reichel <sre@debian.org>
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Pali Rohár <pali.rohar@gmail.com>
Cc: Joni Lapilainen <joni.lapilainen@gmail.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: stable@vger.kernel.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
On Beagle xM Rev. Ax/Bx, the USB power enable GPIO logic is
reversed when compared to other revisions i.e. it is
active high instead of active low.
Use the beagle_config.usb_pwr_level flag correctly so that
the power regulator can be configured at runtime.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
- XRC transport fixes
- Fix DHCP on IPoIB
- mlx4 preparations for flow steering
- iSER fixes
- miscellaneous other fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=1ojD
-----END PGP SIGNATURE-----
Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull InfiniBand/RDMA changes from Roland Dreier:
- XRC transport fixes
- Fix DHCP on IPoIB
- mlx4 preparations for flow steering
- iSER fixes
- miscellaneous other fixes
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (23 commits)
IB/iser: Add support for iser CM REQ additional info
IB/iser: Return error to upper layers on EAGAIN registration failures
IB/iser: Move informational messages from error to info level
IB/iser: Add module version
mlx4_core: Expose a few helpers to fill DMFS HW strucutures
mlx4_core: Directly expose fields of DMFS HW rule control segment
mlx4_core: Change a few DMFS fields names to match firmare spec
mlx4: Match DMFS promiscuous field names to firmware spec
mlx4_core: Move DMFS HW structs to common header file
IB/mlx4: Set link type for RAW PACKET QPs in the QP context
IB/mlx4: Disable VLAN stripping for RAW PACKET QPs
mlx4_core: Reduce warning message for SRQ_LIMIT event to debug level
RDMA/iwcm: Don't touch cmid after dropping reference
IB/qib: Correct qib_verbs_register_sysfs() error handling
IB/ipath: Correct ipath_verbs_register_sysfs() error handling
RDMA/cxgb4: Fix SQ allocation when on-chip SQ is disabled
SRPT: Fix odd use of WARN_ON()
IPoIB: Fix ipoib_hard_header() return value
RDMA: Rename random32() to prandom_u32()
RDMA/cxgb3: Fix uninitialized variable
...
specifics (the 'gic' branch merged), it can be enabled on arm64.
- Enable arm64 support for poweroff/restart (for code under
drivers/power/reset/).
- Fixes (dts file, exception handling, bitops)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.9 (GNU/Linux)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=qd94
-----END PGP SIGNATURE-----
Merge tag 'arm64-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cmarinas/linux-aarch64
Pull arm64 update from Catalin Marinas:
- Since drivers/irqchip/irq-gic.c no longer has dependencies on arm32
specifics (the 'gic' branch merged), it can be enabled on arm64.
- Enable arm64 support for poweroff/restart (for code under
drivers/power/reset/).
- Fixes (dts file, exception handling, bitops)
* tag 'arm64-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cmarinas/linux-aarch64:
arm64: Treat the bitops index argument as an 'int'
arm64: Ignore the 'write' ESR flag on cache maintenance faults
arm64: dts: fix #address-cells for foundation-v8
arm64: vexpress: Add support for poweroff/restart
arm64: Enable support for the ARM GIC interrupt controller
This patch-set includes the following major enhancement patches.
o introduce a new gloabl lock scheme
o add tracepoints on several major functions
o fix the overall cleaning process focused on victim selection
o apply the block plugging to merge IOs as much as possible
o enhance management of free nids and its list
o enhance the readahead mode for node pages
o address several cretical deadlock conditions
o reduce lock_page calls
The other minor bug fixes and enhancements are as follows.
o calculation mistakes: overflow
o bio types: READ, READA, and READ_SYNC
o fix the recovery flow, data races, and null pointer errors
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=Hqii
-----END PGP SIGNATURE-----
Merge tag 'f2fs-for-v3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/jaegeuk/f2fs
Pull f2fs updates from Jaegeuk Kim:
"This patch-set includes the following major enhancement patches.
- introduce a new gloabl lock scheme
- add tracepoints on several major functions
- fix the overall cleaning process focused on victim selection
- apply the block plugging to merge IOs as much as possible
- enhance management of free nids and its list
- enhance the readahead mode for node pages
- address several cretical deadlock conditions
- reduce lock_page calls
The other minor bug fixes and enhancements are as follows.
- calculation mistakes: overflow
- bio types: READ, READA, and READ_SYNC
- fix the recovery flow, data races, and null pointer errors"
* tag 'f2fs-for-v3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/jaegeuk/f2fs: (68 commits)
f2fs: cover free_nid management with spin_lock
f2fs: optimize scan_nat_page()
f2fs: code cleanup for scan_nat_page() and build_free_nids()
f2fs: bugfix for alloc_nid_failed()
f2fs: recover when journal contains deleted files
f2fs: continue to mount after failing recovery
f2fs: avoid deadlock during evict after f2fs_gc
f2fs: modify the number of issued pages to merge IOs
f2fs: remove useless #include <linux/proc_fs.h> as we're now using sysfs as debug entry.
f2fs: fix inconsistent using of NM_WOUT_THRESHOLD
f2fs: check truncation of mapping after lock_page
f2fs: enhance alloc_nid and build_free_nids flows
f2fs: add a tracepoint on f2fs_new_inode
f2fs: check nid == 0 in add_free_nid
f2fs: add REQ_META about metadata requests for submit
f2fs: give a chance to merge IOs by IO scheduler
f2fs: avoid frequent background GC
f2fs: add tracepoints to debug checkpoint request
f2fs: add tracepoints for write page operations
f2fs: add tracepoints to debug the block allocation
...
Pull Hexagon fixes from Richard Kuo:
"A bug fix and a Kconfig cleanup"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rkuo/linux-hexagon-kernel:
HEXAGON: Remove non existent reference to GENERIC_KERNEL_EXECVE & GENERIC_KERNEL_THREAD
Hexagon: fix register used to call do_work_pending
Commit ff5c9059 (ARM: dts: OMAP3+: Correct gpio #interrupts-cells
property) updated the number of interrupt cells required for configuring
gpios as interrupts for other devices (such as ethernet controllers).
This update allowed the interrupt type (edge, level, etc) to be
configured via device-tree (as described in the
Documentation/devicetree/bindings/gpio/gpio-omap.txt).
This broke ethernet support on the OMAP4 SDP board that defines a gpio
as the ethernet IRQ because the interrupt type (level, edge, etc) was
not getting configured correctly. This board use the ks8851 ethernet
chip which has an active low interrupt. Fix this by defining the gpio
interrupt as active-low in the device-tree binding.
Please note that the OMAP4-VAR-SOM also uses the same ethernet
controller and it is expected it will have the same problem. So the
same fix is also applied to this board.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 8a965b3baa ("mm, slab_common: Fix bootstrap creation of kmalloc
caches") introduced a regression that caused us to crash early during
boot. The commit was introducing ordering of slab creation, making sure
two odd-sized slabs were created after specific powers of two sizes.
But, if any of the power of two slabs were created earlier during boot,
slabs at index 1 or 2 might not get created at all. This patch makes
sure none of the slabs get skipped.
Tony Lindgren bisected this down to the offending commit, which really
helped because bisect kept bringing me to almost but not quite this one.
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
Acked-by: Christoph Lameter <cl@linux.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Tested-by: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp>
Tested-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Unlike meta data server mounts which support multiple mount points to
the same server via struct nfs_server, data servers support a single connection.
Concurrent calls to setup the data server connection can race where the first
call allocates the nfs_client struct, and before the cache struct nfs_client
pointer can be set, a second call also tries to setup the connection, finds the
already allocated nfs_client, bumps the reference count, re-initializes the
session,etc. This results in a hanging data server session after umount.
Signed-off-by: Andy Adamson <andros@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Protect the SIOCGCM* ioctl macros with parenthesis.
Reported-by: Paul Wouters <pwouters@redhat.com>
Signed-off-by: Josh Boyer <jwboyer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than having logic to calculate inner protocol in every
tunnel gso handler move it to gso code. This simplifies code.
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Cong Wang <amwang@redhat.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
reproduce steps
1. flood ping from other machine
ping -f -s 41000 IP
2. run below script
while [ 1 ]; do ethtool -s eth0 autoneg off;
sleep 3;ethtool -s eth0 autoneg on; sleep 4; done;
You can see oops in one hour.
The reason is fec_restart clear BD but NAPI may use it.
The solution is disable NAPI and stop xmit when reset BD.
disable NAPI may sleep, so fec_restart can't be call in
atomic context.
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of error, the function ptp_clock_register() returns ERR_PTR()
and never returns NULL. The NULL test in the return value check should
be replaced with IS_ERR().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix to return -ENOMEM in the irlap_open() error handling case instead
of 0(overwrite to 0 by bfin_sir_startup()), as done elsewhere in this
function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_mdiobus_register creates a phy_device even if get_phy_device failed
to create it previously. This causes indefinite polling on non-existent
PHYs. This fix makes of_mdio_register rely on get_phy_device to
properly create the device or fail otherwise.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver and firmware sync up through SYNC messages, and the
firmware's affirmative reply to these SYNC messages appears to be the
"Reset" indication received via the status interrupt endpoint. Thus the
driver needs the status interrupt endpoint always active so that the
Reset indication can be received even if the netdev is closed, which is
the case right after device insertion.
If the Reset indication is not received by the driver, it continues
sending SYNC messages to the firmware, which crashes about 10 seconds
later and the device stops responding.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some drivers (sierra_net) need the status interrupt URB
active even when the device is closed, because they receive
custom indications from firmware. Add functions to refcount
the status interrupt URB submit/kill operation so that
sub-drivers and the generic driver don't fight over whether
the status interrupt URB is active or not.
A sub-driver can call usbnet_status_start() at any time, but
the URB is only submitted the first time the function is
called. Likewise, when the sub-driver is done with the URB,
it calls usbnet_status_stop() but the URB is only killed when
all users have stopped it. The URB is still killed and
re-submitted for suspend/resume, as before, with the same
refcount it had at suspend.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Acked-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
A rebranded Novatel E371 for AT&T's LTE bands. qmi_wwan should drive this
device, while cdc_ether should ignore it. Even though the USB descriptors
are plain CDC-ETHER that USB interface is a QMI interface.
Cc: <stable@vger.kernel.org>
Signed-off-by: Dan Williams <dcbw@redhat.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
be_close() followed by be_clear() is called as a part of cleanup in the
EEH/AER flow. This patch stops TX in be_close() before cleaning/freeing
up the TX queues in be_clear(). This prevents be_xmit() from being called
while TX queues no longer exist.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While cleaning RX queues, the CQ DB may be rung several times (with rearm)
while waiting for the flush compl. Each CQ-notify with rearm can result in
an event. The EQ may get full resulting in a HW error.
Fix this by not re-arming the CQ while notifying a valid completion.
Also, there's no need to wait for 1ms after destroying RXQ, as the code in
be_rx_cq_clean() waits for the flush compl to arrive.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The buffer size for a FW cmd request must be big enough to fit the response,
else the cmd fails. For GET_MAC_LIST cmd, though the memory allocated for
the cmd is big enough to fit the response, the payload_len value in the
WRB hdr is being set to the request length only.
Fix this for GET_MAC_LIST cmd.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the PF driver calls pci_enable_sriov(), the VFs may be probed
inline before the call returns. So, the resources required for all VFs
must be provisioned by the PF driver *before* calling pci_enable_sriov();
else, VF probe will fail.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull block driver updates from Jens Axboe:
"It might look big in volume, but when categorized, not a lot of
drivers are touched. The pull request contains:
- mtip32xx fixes from Micron.
- A slew of drbd updates, this time in a nicer series.
- bcache, a flash/ssd caching framework from Kent.
- Fixes for cciss"
* 'for-3.10/drivers' of git://git.kernel.dk/linux-block: (66 commits)
bcache: Use bd_link_disk_holder()
bcache: Allocator cleanup/fixes
cciss: bug fix to prevent cciss from loading in kdump crash kernel
cciss: add cciss_allow_hpsa module parameter
drivers/block/mg_disk.c: add CONFIG_PM_SLEEP to suspend/resume functions
mtip32xx: Workaround for unaligned writes
bcache: Make sure blocksize isn't smaller than device blocksize
bcache: Fix merge_bvec_fn usage for when it modifies the bvm
bcache: Correctly check against BIO_MAX_PAGES
bcache: Hack around stuff that clones up to bi_max_vecs
bcache: Set ra_pages based on backing device's ra_pages
bcache: Take data offset from the bdev superblock.
mtip32xx: mtip32xx: Disable TRIM support
mtip32xx: fix a smatch warning
bcache: Disable broken btree fuzz tester
bcache: Fix a format string overflow
bcache: Fix a minor memory leak on device teardown
bcache: Documentation updates
bcache: Use WARN_ONCE() instead of __WARN()
bcache: Add missing #include <linux/prefetch.h>
...
We have registered platform device when module init, and
need unregister it when module exit.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Pull block core updates from Jens Axboe:
- Major bit is Kents prep work for immutable bio vecs.
- Stable candidate fix for a scheduling-while-atomic in the queue
bypass operation.
- Fix for the hang on exceeded rq->datalen 32-bit unsigned when merging
discard bios.
- Tejuns changes to convert the writeback thread pool to the generic
workqueue mechanism.
- Runtime PM framework, SCSI patches exists on top of these in James'
tree.
- A few random fixes.
* 'for-3.10/core' of git://git.kernel.dk/linux-block: (40 commits)
relay: move remove_buf_file inside relay_close_buf
partitions/efi.c: replace useless kzalloc's by kmalloc's
fs/block_dev.c: fix iov_shorten() criteria in blkdev_aio_read()
block: fix max discard sectors limit
blkcg: fix "scheduling while atomic" in blk_queue_bypass_start
Documentation: cfq-iosched: update documentation help for cfq tunables
writeback: expose the bdi_wq workqueue
writeback: replace custom worker pool implementation with unbound workqueue
writeback: remove unused bdi_pending_list
aoe: Fix unitialized var usage
bio-integrity: Add explicit field for owner of bip_buf
block: Add an explicit bio flag for bios that own their bvec
block: Add bio_alloc_pages()
block: Convert some code to bio_for_each_segment_all()
block: Add bio_for_each_segment_all()
bounce: Refactor __blk_queue_bounce to not use bi_io_vec
raid1: use bio_copy_data()
pktcdvd: Use bio_reset() in disabled code to kill bi_idx usage
pktcdvd: use bio_copy_data()
block: Add bio_copy_data()
...
Add definitions for the three Firmware Activate actions, and change the
SCSI translation code to construct the command into a temporary variable
instead of translating the endianness back-and-forth.
Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com>
Reviewed-by: Vishal Verma <vishal.l.verma@linux.intel.com>
Many of the bits in the Controller Configuration register may only be
modified when the Enable bit is clear. Clearing them at the same time
as the Enable bit might be OK, but let's play it safe and only touch the
Enable bit.
Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
A recent update to the specification makes it clear that the host
is expected to wait for the device to acknowledge the Enable bit
transitioning to 0 as well as waiting for the device to acknowledge a
transition to 1.
Reported-by: Khosrow Panah <Khosrow.Panah@idt.com>
Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Userspace is not meant to have to handle all strange dB ranges,
so add a specification comment.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This change fixes a problem introduced by recent commit c34c82b
(ACPICA: Predefine names: Add allowed argument types to master info
table) in 20130328 where _INI methods are no longer executed properly
because of a memory block that is not initialized properly. ACPICA
BZ1016. Tomasz Nowicki <tomasz.nowicki@linaro.org>
References: https://bugs.acpica.org/show_bug.cgi?id=1016
Signed-off-by: Tomasz Nowicki <tomasz.nowicki@linaro.org>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Fixes a possible memory leak in the error exit path introduced by
recent commit 388a990 ("ACPICA: _OSI Support: handle any errors from
acpi_os_acquire_mutex()").
[rjw: Changelog]
Signed-off-by: Jung-uk Kim <jkim@FreeBSD.org>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Can only happen under these conditions: 1) The DSDT version is 1,
meaning integers are 32-bits. 2) The field is between 33 and 64
bits long.
It applies cleanly back to ACPICA 20100806+ (Linux v2.6.37+).
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Cc: 2.6.37+ <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
After build_free_nids() searches free nid candidates from nat pages and
current journal blocks, it checks all the candidates if they are allocated
so that the nat cache has its nid with an allocated block address.
In this procedure, previously we used
list_for_each_entry_safe(fnid, next_fnid, &nm_i->free_nid_list, list).
But, this is not covered by free_nid_list_lock, resulting in null pointer bug.
This patch moves this checking routine inside add_free_nid() in order not to use
the spin_lock.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
When nm_i->fcnt > 2 * MAX_FREE_NIDS, stop scanning other NAT entries.
Signed-off-by: Haicheng Li <haicheng.li@linux.intel.com>
[Jaegeuk Kim: fix handling the return value of add_free_nid()]
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
This patch does two cleanups:
1. remove unused variable "fcnt" in build_free_nids().
2. make scan_nat_page() as void type and remove useless variable "fcnt".
Signed-off-by: Haicheng Li <haicheng.li@linux.intel.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Directly drop the free_nid cache when nm_i->fcnt > 2 * MAX_FREE_NIDS
Since there is NOT nmi->free_nid_list_lock spinlock protection between
a sequential calling of alloc_nid() and alloc_nid_failed(), some other
threads may already add new free_nid to the free_nid_list during this
period.
We need to make sure nmi->fcnt is never > 2 * MAX_FREE_NIDS.
Signed-off-by: Haicheng Li <haicheng.li@linux.intel.com>
[Jaegeuk Kim: fit the coding style]
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
When recovering a journal file with fsync data for files that have
been deleted, don't bail out on recovery.
Signed-off-by: Chris Fries <C.Fries@motorola.com>
Reviewed-by: Russell Knize <rknize2@motorola.com>
Reviewed-by: Jason Hrycay <jason.hrycay@motorola.com>
[Jaegeuk Kim: fit the coding style]
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
When unable to roll forward the journal, we shouldn't bail out and
not mount, we should continue to attempt the mount. Bad recovery data
is likely unrecoverable at this point, and requiring the user to try
to mount again doesn't solve any issues.
Signed-off-by: Chris Fries <C.Fries@motorola.com>
Reviewed-by: Russell Knize <rknize2@motorola.com>
Reviewed-by: Jason Hrycay <jason.hrycay@motorola.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
o Deadlock case #1
Thread 1:
- writeback_sb_inodes
- do_writepages
- f2fs_write_data_pages
- write_cache_pages
- f2fs_write_data_page
- f2fs_balance_fs
- wait mutex_lock(gc_mutex)
Thread 2:
- f2fs_balance_fs
- mutex_lock(gc_mutex)
- f2fs_gc
- f2fs_iget
- wait iget_locked(inode->i_lock)
Thread 3:
- do_unlinkat
- iput
- lock(inode->i_lock)
- evict
- inode_wait_for_writeback
o Deadlock case #2
Thread 1:
- __writeback_single_inode
: set I_SYNC
- do_writepages
- f2fs_write_data_page
- f2fs_balance_fs
- f2fs_gc
- iput
- evict
- inode_wait_for_writeback(I_SYNC)
In order to avoid this, even though iput is called with the zero-reference
count, we need to stop the eviction procedure if the inode is on writeback.
So this patch links f2fs_drop_inode which checks the I_SYNC flag.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Changes for pure microMIPS cores to dynamically determine the ASID
size at boot time.
Includes bug fix https://patchwork.linux-mips.org/patch/5230/
Signed-off-by: Steven J. Hill <Steven.Hill@imgtec.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Original patch by Ralf Baechle and removed by Harold Koerfgen
with commit f67e4ffc79905482c3b9b8c8dd65197bac7eb508. This
allows for more generic kernels since the size of the ASID
and corresponding masks can be determined at run-time. This
patch is also required for the new Aptiv cores and has been
tested on Malta and Malta Aptiv platforms.
[ralf@linux-mips.org: Added relevant part of fix
https://patchwork.linux-mips.org/patch/5213/]
Signed-off-by: Steven J. Hill <Steven.Hill@imgtec.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Remove 'arch/mips/include/asm/mips-boards/prom.h' and get rid of
all inclusions of it by Malta and SEAD-3 platforms.
[ralf@linux-mips.org: Fold in John Crispin <blogic@openwrt.org>'s "MIPS:
ar7 powertv build"].
[ralf@linux-mips.org: Fold in John Crispin <blogic@openwrt.org>'s "MIPS:
unbreak powertv build"].
[ralf@linux-mips.org: Test. Build. Your. Fscking. Code. Or...]
Signed-off-by: Steven J. Hill <Steven.Hill@imgtec.com>
Kevin Hilman
Aaro Koskinen
Roger Quadros
Linus Torvalds
Jon Hunter
Chris Mason
Andy Adamson
Roland Dreier
Josh Boyer
Pravin B Shelar
Frank Li
Wei Yongjun
Sebastian Hesselbarth
Dan Williams
Sathya Perla
Matthew Wilcox
David Henningsson
Tomasz Nowicki
Jung-uk Kim
Bob Moore
Jaegeuk Kim
Haicheng Li
Chris Fries
Steven J. Hill