* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (56 commits)
sh: Fix declaration of __kernel_sigreturn and __kernel_rt_sigreturn
sh: Enable soc-camera in ap325rxa/migor/se7724 defconfigs.
sh: remove stray markers.
sh: defconfig updates.
sh: pci: Initial PCI-Express support for SH7786 Urquell board.
sh: Generic HAVE_PERF_COUNTER support.
SH: convert migor to soc-camera as platform-device
SH: convert ap325rxa to soc-camera as platform-device
soc-camera: unify i2c camera device platform data
sh: add platform data for r8a66597-hcd in setup-sh7723
sh: add platform data for r8a66597-hcd in setup-sh7366
sh: x3proto: add platform data for r8a66597-hcd
sh: highlander: add platform data for r8a66597-hcd
sh: sh7785lcr: add platform data for r8a66597-hcd
sh: turn off irqs when disabling CMT/TMU timers
sh: use kzalloc() for cpg clocks
sh: unbreak WARN_ON()
sh: Use generic atomic64_t implementation.
sh: Revised clock function in highlander
sh: Update r7780mp defconfig
...
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (55 commits)
netxen: fix tx ring accounting
netxen: fix detection of cut-thru firmware mode
forcedeth: fix dma api mismatches
atm: sk_wmem_alloc initial value is one
net: correct off-by-one write allocations reports
via-velocity : fix no link detection on boot
Net / e100: Fix suspend of devices that cannot be power managed
TI DaVinci EMAC : Fix rmmod error
net: group address list and its count
ipv4: Fix fib_trie rebalancing, part 2
pkt_sched: Update drops stats in act_police
sky2: version 1.23
sky2: add GRO support
sky2: skb recycling
sky2: reduce default transmit ring
sky2: receive counter update
sky2: fix shutdown synchronization
sky2: PCI irq issues
sky2: more receive shutdown
sky2: turn off pause during shutdown
...
Manually fix trivial conflict in net/core/skbuff.c due to kmemcheck
* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog:
[WATCHDOG] hpwdt: Add NMI sourcing
[WATCHDOG] iTCO_wdt: Fix ICH7+ reboot issue.
[WATCHDOG] iTCO_wdt: fix memory corruption when RCBA is disabled by hardware
[WATCHDOG] Correct WDIOF_MAGICCLOSE flag
[WATCHDOG] move platform probe and remove function to devinit and devexit
[WATCHDOG] Some more general cleanup
[WATCHDOG] iTCO_wdt: Cleanup code
* 'for-linus' of git://neil.brown.name/md: (39 commits)
md/raid5: correctly update sync_completed when we reach max_resync
md/raid5: add missing call to schedule() after prepare_to_wait()
md/linear: use call_rcu to free obsolete 'conf' structures.
md linear: Protecting mddev with rcu locks to avoid races
md: Move check for bitmap presence to personality code.
md: remove chunksize rounding from common code.
md: raid0/linear: ensure device sizes are rounded to chunk size.
md: move assignment of ->utime so that it never gets skipped.
md: Push down reconstruction log message to personality code.
md: merge reconfig and check_reshape methods.
md: remove unnecessary arguments from ->reconfig method.
md: raid5: check stripe cache is large enough in start_reshape
md: raid0: chunk_sectors cleanups.
md: fix some comments.
md/raid5: Use is_power_of_2() in raid5_reconfig()/raid6_reconfig().
md: convert conf->chunk_size and conf->prev_chunk to sectors.
md: Convert mddev->new_chunk to sectors.
md: Make mddev->chunk_size sector-based.
md: raid0 :Enables chunk size other than powers of 2.
md: prepare for non-power-of-two chunk sizes
...
This patch adds the kernel side of the PPS support currently named
"LinuxPPS".
PPS means "pulse per second" and a PPS source is just a device which
provides a high precision signal each second so that an application can
use it to adjust system clock time.
Common use is the combination of the NTPD as userland program with a GPS
receiver as PPS source to obtain a wallclock-time with sub-millisecond
synchronisation to UTC.
To obtain this goal the userland programs shoud use the PPS API
specification (RFC 2783 - Pulse-Per-Second API for UNIX-like Operating
Systems, Version 1.0) which in part is implemented by this patch. It
provides a set of chars devices, one per PPS source, which can be used to
get the time signal. The RFC's functions can be implemented by accessing
to these char devices.
Signed-off-by: Rodolfo Giometti <giometti@linux.it>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Greg KH <greg@kroah.com>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Michael Kerrisk <mtk.manpages@googlemail.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the copyright statements in a couple of GRU files. No functional
changes are being made.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Delete references to the SGI GRU GSH hardware resources. These GRU
resources have been deleted from the hardware. (These resources have
never benn used, anyway).
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Minor fixes to the SGI GRU grudump facility:
- fix address where user data is written
- add gru number to data passed to user
- indicate if context is locked
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix potential SGI GRU bug that could cause a use-after-free. If one
thread in a task is flushing the GRU and another thread destroys the GRU
context, there is the potential to access a table after it has been freed.
Copy the gms pointer to a local variable before unlocking the gts table.
Note that no refcnt is needed for the gms - the reference is held
indirectly by the task's mm_struct.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a user request to specify the gru instruction slice parameter for user
contexts.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Change the user GRU request for specifying the "task_slice" option to use
a generic infrastructure that can be expanded in the future to include
additional context options. No new capabilities are added with this
patch.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cleanup of GRU inline functions to eliminate unnecessary inline code.
Update function descriptions.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Delete the user request for fetching the status of a GRU chiplet. This
request has been made obsolete by other changes. Note: this is not a
change to a user API - there are no compatibility issues with this change.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Collect GRU statistics for each user GRU context. Statistics are kept for
TLB misses & content resource contention. Add user request for retrieving
the statistics.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix bug in automatic retry of GRU instruction failures. CBR substatus
(message queue failure) was being checked incorrectly.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add user function to explicitly unload GRU kernel contexts from the GRU.
Only contexts that are not in-use will be unloaded.
This function is primarily for testing. It is not expected that this will
be used in normal production systems.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix two problems related to GRU instruction failures. Cache coherency is
not maintained for CBEs except when loading or unloading contexts. When
reading a CBE to extract error information, the CBE must first be flushed
from the cache.
The function that reads kerrnel CBEs was reading the wrong CBE.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Update GRU driver to the latest version of the GRU spec. This consists
of minor updates:
- changes & additions to error status bits
- new restriction on handling of TLB misses while in FMM mode
- new field (not used by software) in TFH
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Change the kernel self tests that can be optionally executed on GRU
initialization. This is primarily for testing.
Eliminate the BUG statements on failure and return bad status. Add ioctl
interface to execute the tests on demand.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for asynchronous GRU instructions. Currently, asynchronous
instructions are supported only for GRU instructions issued by the kernel.
[akpm@linux-foundation.org: build fix]
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for interrupts generated by GRU instruction completion.
Previously, the only interrupts were for TLB misses. The hardware also
supports interrupts on instruction completion. This will be supported for
instructions issued by the kernel.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Check whether the gru state being loaded into a gru is from a new context
or a previously unloaded context. If new, simply zero out the hardware
context; if unloaded and valid, reload the old state.
This change is primarily for reloading kernel contexts where the previous
is not required to be saved.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix endcase in handling GRU message queue failures due to NACKs of PUT
requests. Must ensure that the "present" bits are cleared before
resending the message.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Support alocation of GRU contexts that contain zero DSR or CBR resources.
Some instructions do not require DSR resources. Contexts without CBR
resources are useful for diagnostics.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Change the way GRU resources are assigned for kernel threads. GRU
contexts for kernel threads are now allocated on demand and can be stolen
by user processes when idle. This allows MPI jobs to use ALL of the GRU
resources when the kernel is not using them.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Change the interface to cch_allocate so that it can be used to allocate
GRU contexts for kernel threads. Kernel threads use the GRU in unmapped
mode and do not require ASIDs for the GRU TLB.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove "static" from the functions for loading/unloading GRU contexts.
These functions will be called from other GRU files. Fix bug in unlocking
gru context.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Change the interface to gru_alloc_gts() so that it can be used to allocate
GRU contexts for kernel threads. Kernel threads do not have vdata
structures for the GRU contexts. The GRU resource count are now passed
explicitly instead of inside the vdata structure.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for dumpping the state of an entire GRU chiplet.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Bug fixes for GRU exception handling. Additional fields from the CBR must
be returned to the user to allow the user to correctly diagnose GRU
exceptions.
Handle endcase in TFH TLB miss handling. Verify that TFH actually
indicates a pending exception.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently the sysrq-c handler is bit over-engineered. Its behavior is
dependent on a few compile time and run time factors that alter its
behavior which is really unnecessecary.
If CONFIG_KEXEC is not configured, sysrq-c, crashes the system with a NULL
pointer dereference. If CONFIG_KEXEC is configured, it calls crash_kexec
directly, which implies that the kexec kernel will either be booted (if
its been previously loaded), or it will simply do nothing (the no kexec
kernel has been loaded).
It would be much easier to just simplify the whole thing to dereference a
NULL pointer all the time regardless of configuration. That way, it will
always try to crash the system, and if a kexec kernel has been loaded into
reserved space, it will still boot from the page fault trap handler
(assuming panic_on_oops is set appropriately).
[akpm@linux-foundation.org: build fix]
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Cc: Brayan Arraes <brayan@yack.com.br>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On embedded devices, sleep mode conditions can be tricky to handle,
Especially when processors tend to pull-down the w1 bus during sleep. Bus
slaves (such as the ds2760) may interpret this as a reason for power-down
conditions and entirely switch off the device.
This patch adds a callback function pointer to let users switch on and off
the external pull-up resistor. This lets the outside world know whether
the processor is currently actively driving the bus or not.
When this callback is not provided, the code behaviour won't change.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Acked-by: Ville Syrjala <syrjala@sci.fi>
Acked-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The remove function uses __devexit, so the .remove assignment needs
__devexit_p() to fix a build error with hotplug disabled.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add edac_device_alloc_index(), because for MAPLE platform there may
exist several EDAC driver modules that could make use of
edac_device_ctl_info structure at the same time. The index allocation
for these structures should be taken care of by EDAC core.
[akpm@linux-foundation.org: cleanups]
Signed-off-by: Harry Ciao <qingtao.cao@windriver.com>
Cc: Doug Thompson <norsk5@yahoo.com>
Cc: Michael Ellerman <michael@ellerman.id.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Introduce IBM CPC925 EDAC driver, which makes use of ECC, CPU and
HyperTransport Link error detections and corrections on the IBM
CPC925 Bridge and Memory Controller.
[akpm@linux-foundation.org: cleanup]
Signed-off-by: Harry Ciao <qingtao.cao@windriver.com>
Cc: Doug Thompson <norsk5@yahoo.com>
Cc: Michael Ellerman <michael@ellerman.id.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
One of my programs frequently grabs the parport, does something with it
and then drops it again. This results in spamming of the kernel log with
"... registered pardevice"
"... unregistered pardevice"
These messages are completely useless, except for debugging ppdev,
probably. So put them under DEBUG (or dynamic debug).
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix this:
isicom.c: In function `isicom_probe':
isicom.c:1587: warning: `signature' may be used uninitialized in this function
by uninitialized_var(), because if the signature is not initialized in
reset_card(), we won't use it.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
memory_open() ignores devlist and does a switch for each item, duplicating
code and conditional definitions.
Clean it up by adding backing_dev_info to devlist and use it to lookup for
the minor device.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Adriano dos Santos Fernandes <adrianosf@uol.com.br>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
PCA9556 is the software-compatible predecessor to the PCA9557, so add it
to the supported I2C device ID table.
Signed-off-by: Nate Case <ncase@xes-inc.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On OpenFirmware platforms, it makes the most sense to get platform_data
from the device tree. Make an attempt to translate OF node properties
into platform_data struct before bailing out.
Note that the implementation approach taken differs from other device
drivers that make use of device tree information. This is because I2C
chips are already registered automatically by of_i2c, so we can get by
with a small translator function in the driver.
[akpm@linux-foundation.org: coding-style fixes]
[akpm@linux-foundation.org: kfree(NULL) is legal]
Signed-off-by: Nate Case <ncase@xes-inc.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The remove member of the spi_driver max7301_driver uses __devexit_p(), so
the remove function itself should be marked with __devexit. Even more so
considering the probe function is marked with __devinit.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Juergen Beisert <j.beisert@pengutronix.de>
Cc: Dmitry Baryshkov <dbaryshkov@gmail.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support to the PCA953x driver to use the GPIOLIB naming facility for
GPIOs.
Signed-off-by: Daniel Silverstone <dsilvers@simtec.co.uk>
Cc: Ben Gardner <bgardner@wabtec.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Blackfin platforms do not support the hardware which this driver drives.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: David Brownell <david-b@pacbell.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
IRQF_SHARED should not be used with IRQF_DISABLED. There is no in-tree
user of this driver and only out-of-tree user I know uses a dedicated irq
line for this RTC.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
IRQF_SHARED should not be used with IRQF_DISABLED. This RTC have a
dedicated irq line to SoC's internal interrupt controller so there is
no reason to use IRQF_SHARED.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for the Epson RX-8025SA/NB RTC chips. It includes support for
alarms, periodic interrupts (1 Hz) and clock precision adjustment.
For clock precision adjustment, the SYSFS file "clock_adjust_ppb" gets
created in "/sys/class/rtc/rtcX/device". It permits to set and get the
clock adjustment in ppb (parts per billion), e.g.:
# echo -183000 > /sys/class/rtc/rtc0/device/clock_adjust_ppb
# cat /sys/class/rtc/rtc0/device/clock_adjust_ppb
-183000
This allows to compensate temperature dependent clock drifts. According
to the RX8025 SA/NB application manual the frequency and temperature
characteristics can be approximated using the following equation:
df = a * (ut - t)**2
df: Frequency deviation in any temperature
a : Coefficient = (-35 +-5) * 10**-9
ut: Ultimate temperature in degree = +25 +-5 degree
t : Any temperature in degree
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Sergei Poselenov <sposelenov@emcraft.com>
Signed-off-by: Yuri Tikhonov <yur@emcraft.com>
Signed-off-by: Dmitry Rakhchev <rda@emcraft.com>
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add ds3231 variant. For that, the BBSQI bit position was changed from a
simple define into a lookup-array as it differs. This also removes
writing to an unused bit in case of the ds1337.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The RTC driver for ds1742 / ds1743 uses a static nvram attribute. This
patch replaces this static attribute with one nvram attribute for each
ds174x registered.
The nvram size is not the same for all types of ds174x. The nvram size is
accessible as the file size of the nvram attribute in sysfs. With only a
single nvram attribute, this file size will be incorrect if more than one
type of ds174x is present on a system. See the comment in the removed
code below.
This patch have been tested with linux-2.6.28 and linux-2.6.29-rc5/6 on a
custom board with one ds1743.
Signed-off-by: Torsten Ertbjerg Rasmussen <ertbjerg@gmail.com>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Buffer needs not be dma-safe, not rx data length.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit a7bb3909b3 ("spi: pxa2xx_spi:
introduce chipselect GPIO to simplify the common cases") introduces
chipselect GPIO, and configures the CS polarity using SPI_CS_HIGH
spi->mode flag. Add SPI_CS_HIGH to the allowed modes.
Signed-off-by: Daniel Ribeiro <drwyrm@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
mpc52xx_psc_spi driver is the last user of the legacy activate_cs and
deactivate_cs callbacks, so convert the driver to the cs_control hook and
remove the legacy callbacks from fsl_spi_platform_data struct.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move some common spi_setup() error checks into the SPI framework from the
spi_master controller drivers:
- Add a new "mode_bits" field to spi_master
- Use that in spi_setup to validate the spi->mode value being
requested. Setting this new field is now mandatory for any
controller supporting more than vanilla SPI_MODE_0.
- Update all spi_master drivers to:
* Initialize that field
* Remove current spi_setup() checks using that value.
This is a net minor code shrink.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Start moving some spi_setup() functionality into the SPI core from the
various spi_master controller drivers:
- Make that function stop being an inline;
- Move two common idioms from drivers into that new function:
* Default bits_per_word to 8 if that field isn't set
* Issue a standardized dev_dbg() message
This is a net minor source code shrink, and supports enhancments found in
some follow-up patches.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
bfin_spi_flush() returns limit, which reaches -1 upon timeout. but in
function bfin_spi_pump_transfers() it is compared with 0.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This forces every update of tx ring producer to check for
availability of space for next full TSO command. Earlier
firmware control commands didn't care to pause tx queue.
Stop the tx queue if there's not enough space to transmit one full
LSO command left on the tx ring after current transmit. This avoids
returning NETDEV_TX_BUSY after checking distance between producer
and consumer on every cpu.
Restart the tx queue only if we have cleaned up enough tx
descriptors.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the detection of cut-thru mode of the hardware (direct dma
to host) to mode configured in SRE (ingress block) rather than
onboard memory control.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
forcedeth doesnt use properly dma api in its tx completion path
and in nv_loopback_test()
pci_map_single() should be paired with pci_unmap_single()
pci_map_page() should be paired with pci_unmap_page()
forcedeth xmit path uses pci_map_single() & pci_map_page(),
but tx completion path only uses pci_unmap_single()
nv_loopback_test() uses pci_map_single() & pci_unmap_page()
Add a dma_single field in struct nv_skb_map, and
define a helper function nv_unmap_txskb
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add NMI sourcing functionality (Can only be active if nmi_watchdog is
inactive).
Signed-off-by: Thomas Mingarelli <thomas.mingarelli@hp.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Bugzilla: 9868 & 10195.
There seems to be a bug into the SMM code that handles TCO Timeout SMI.
Andriy Gapon found that the code on his DG33TL system does the following:
> The handler is quite simple - it tests value in TCO1_CNT against 0x800, i.e.
> checks TCO_TMR_HLT. If the bit is set the handler goes into an infinite loop,
> apparently to allow the second timeout and reboot. Otherwise it simply clears
> TIMEOUT bit in TCO1_STS and that's it.
> So the logic seems to be reversed, because it is hard to see how TIMEOUT can
> get set to 1 and SMI generated when TCO_TMR_HLT is set (other than a
> transitional effect).
The only trick we have is to bypass the SMM code by turning of the generation
of the SMI#. The trick can only be enabled by setting the vendorsupport module
parameter to 911. This trick doesn't work well on laptop's.
Note: this is a dirty hack. Please handle with care. The only real fix is that
the bug in the SMM bios code get's fixed.
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
According to 9.1.33 on p.343 of ICH8.pdf RCBA can be disabled by
hardware if bit 0 of RCBA register is not set.
Perform correct check for this to prevent memory corruption under
some virtual machines where this feature is disabled.
Signed-off-by: Denis V. Lunev <den@openvz.org>
CC: Vasily Averin <vvs@openvz.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
A pointer to probe and remove functions is passed to the core via
platform_driver_register and so the function must not disappear when the
.init sections are discarded. Otherwise (if also having HOTPLUG=y)
unbinding and binding a device to the driver via sysfs will result in an
oops as does a device being registered late.
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
If the adapter is not power-manageable using either ACPI, or the
native PCI PM interface, __e100_power_off() returns error code, which
causes every attempt to suspend to fail, although it should return 0
in such a case. Fix this problem by ignoring the return value of
pci_set_power_state() in __e100_power_off().
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Andreas Mohr <andi@lisas.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
clk_disable was called twice in the remove function.
Correct this so that the driver module unloads without error.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is inspired by patch recently posted by Johannes Berg. Basically what
my patch does is to group list and a count of addresses into newly introduced
structure netdev_hw_addr_list. This brings us two benefits:
1) struct net_device becames a bit nicer.
2) in the future there will be a possibility to operate with lists independently
on netdevices (with exporting right functions).
I wanted to introduce this patch before I'll post a multicast lists conversion.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
drivers/net/bnx2.c | 4 +-
drivers/net/e1000/e1000_main.c | 4 +-
drivers/net/ixgbe/ixgbe_main.c | 6 +-
drivers/net/mv643xx_eth.c | 2 +-
drivers/net/niu.c | 4 +-
drivers/net/virtio_net.c | 10 ++--
drivers/s390/net/qeth_l2_main.c | 2 +-
include/linux/netdevice.h | 17 +++--
net/core/dev.c | 130 ++++++++++++++++++--------------------
9 files changed, 89 insertions(+), 90 deletions(-)
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements skb recycling. It reclaims transmitted skb's
for use in the receive ring.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reduce the size of the driver transmit ring to reduce latency
and allow qdisc to do better rate control. Also make it
obvious what the minimum transmit ring allowed is and why.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since it is likely that there are multiple packets received per
interrupt, only update the receive counters once after all
packets are processed.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The logic in sky2_down was incorrect. Receiver could report status
after rx_stop was called.
The steps need to be:
* stop new frames from being transmitted
* shut off transmit/receive logic
* synchronize with NAPI to process status info about transmitter
and receiver
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add some read's to avoid any PCI posting issues when controlling
irq's.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reset more parts of the receive path when device is take offline.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This unblocks the chip if it is stuck in pause cycle during
shutdown.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stopping all activity through ChipCmd and blindly acking the irqs
is neither nice nor completely needed: the transition to low-power
mode does enough work and it apparently keeps the device in a sane
state.
Patch suggested by a fix for http://bugzilla.kernel.org/show_bug.cgi?id=9512
The rtl_shutdown path is kept unchanged so far.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Tested-by: Anders Eriksson <aeriksson@fastmail.fm>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
Signed-off-by: David S. Miller <davem@davemloft.net>
When sis190 driver is trying to get default phy, if it doesn't find home
or lan phy, it falls back to the first phy in the phy list but list_entry()
points to a bogus entry. list_first_entry() should be used instead.
Signed-off-by: Arnaud Patard <apatard@mandriva.com>
Acked-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-- derived from reverted commit 047584ce94
-- reworked by Grant Likely to play nice with commit:
"net: Rework ucc_geth driver to use of_mdio infrastructure"
(0b9da337dc)
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 047584ce94.
This patch meshes badly with "net: Rework ucc_geth driver to use
of_mdio infrastructure" (0b9da337dc).
Since most of the patch needs to be reworked, it is clearer to revert
the patch and then apply the corrected version
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
At the end of reshape_request we update cyrr_resync_completed
if we are about to pause due to reaching resync_max.
However we update it to the wrong value. We need to add the
"reshape_sectors" that have just been reshaped.
Signed-off-by: NeilBrown <neilb@suse.de>
In the unlikely event that reshape progresses past the current request
while it is waiting for a stripe we need to schedule() before retrying
for 2 reasons:
1/ Prevent list corruption from duplicated list_add() calls without
intervening list_del().
2/ Give the reshape code a chance to make some progress to resolve the
conflict.
Cc: <stable@kernel.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Current, when we update the 'conf' structure, when adding a
drive to a linear array, we keep the old version around until
the array is finally stopped, as it is not safe to free it
immediately.
Now that we have rcu protection on all accesses to 'conf',
we can use call_rcu to free it more promptly.
Signed-off-by: NeilBrown <neilb@suse.de>
Due to the lack of memory ordering guarantees, we may have races around
mddev->conf.
In particular, the correct contents of the structure we get from
dereferencing ->private might not be visible to this CPU yet, and
they might not be correct w.r.t mddev->raid_disks.
This patch addresses the problem using rcu protection to avoid
such race conditions.
Signed-off-by: SandeepKsinha <sandeepksinha@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
If the superblock of a component device indicates the presence of a
bitmap but the corresponding raid personality does not support bitmaps
(raid0, linear, multipath, faulty), then something is seriously wrong
and we'd better refuse to run such an array.
Currently, this check is performed while the superblocks are examined,
i.e. before entering personality code. Therefore the generic md layer
must know which raid levels support bitmaps and which do not.
This patch avoids this layer violation without adding identical code
to various personalities. This is accomplished by introducing a new
public function to md.c, md_check_no_bitmap(), which replaces the
hard-coded checks in the superblock loading functions.
A call to md_check_no_bitmap() is added to the ->run method of each
personality which does not support bitmaps and assembly is aborted
if at least one component device contains a bitmap.
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>
It is easiest to round sizes to multiples of chunk size in
the personality code for those personalities which care.
Those personalities now do the rounding, so we can
remove that function from common code.
Also remove the upper bound on the size of a chunk, and the lower
bound on the size of a device (1 chunk), neither of which really buy
us anything.
Signed-off-by: NeilBrown <neilb@suse.de>
This is currently ensured by common code, but it is more reliable to
ensure it where it is needed in personality code.
All the other personalities that care already round the size to
the chunk_size. raid0 and linear are the only hold-outs.
Signed-off-by: NeilBrown <neilb@suse.de>
Currently the assignment to utime gets skipped for 'external'
metadata. So move it to the top of the function so that it
always gets effected.
This is of largely cosmetic interest. Nothing actually depends
on ->utime being right for external arrays.
"mdadm --monitor" does use it for 0.90 and 1.x arrays, but with
mdadm-3.0, this is not important for external metadata.
Signed-off-by: NeilBrown <neilb@suse.de>
Currently, the md layer checks in analyze_sbs() if the raid level
supports reconstruction (mddev->level >= 1) and if reconstruction is
in progress (mddev->recovery_cp != MaxSector).
Move that printk into the personality code of those raid levels that
care (levels 1, 4, 5, 6, 10).
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>
The difference between these two methods is artificial.
Both check that a pending reshape is valid, and perform any
aspect of it that can be done immediately.
'reconfig' handles chunk size and layout.
'check_reshape' handles raid_disks.
So make them just one method.
Signed-off-by: NeilBrown <neilb@suse.de>
Passing the new layout and chunksize as args is not necessary as
the mddev has fields for new_check and new_layout.
This is preparation for combining the check_reshape and reconfig
methods
Signed-off-by: NeilBrown <neilb@suse.de>
In reshape cases that do not change the number of devices,
start_reshape is called without first calling check_reshape.
Currently, the check that the stripe_cache is large enough is
only done in check_reshape. It should be in start_reshape too.
Signed-off-by: NeilBrown <neilb@suse.de>
1/ Raid5 has learned to take over also raid4 and raid6 arrays.
2/ new_chunk in mdp_superblock_1 is in sectors, not bytes.
Signed-off-by: NeilBrown <neilb@suse.de>
A straight-forward conversion which gets rid of some
multiplications/divisions/shifts. The patch also introduces a couple
of new ones, most of which are due to conf->chunk_size still being
represented in bytes. This will be cleaned up in subsequent patches.
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>
This patch renames the chunk_size field to chunk_sectors with the
implied change of semantics. Since
is_power_of_2(chunk_size) = is_power_of_2(chunk_sectors << 9)
= is_power_of_2(chunk_sectors)
these bits don't need an adjustment for the shift.
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>
Instead of starting from the iomem or ioport roots, start from the
parent bus' resources. This fixes a bug where child resources would
appear above their parents resources if they had the same size.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Tested-by: Andrew Patterson <andrew.patterson@hp.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] Convert ia64 to use int-ll64.h
[IA64] Fix build error in paravirt_patchlist.c
[IA64] ia64 does not need umount2() syscall
[IA64] hook up new rt_tgsigqueueinfo syscall
[IA64] msi_ia64.c dmar_msi_type should be static
[IA64] remove obsolete hw_interrupt_type
[IA64] remove obsolete irq_desc_t typedef
[IA64] remove obsolete no_irq_type
[IA64] unexport fpswa.h
For MFDs running regulator cores, we really want them to be brought up early
during boot.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Mike Rapoport <mike@compulab.co.il>
We can not have .driver_data as const since platform_set_drvdata() doesnt take
a const.
The hclk mmc_data field can be const though.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This enables the ASIC3's SD/SDIO MFD cell, supported by the tmio_mmc driver.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This enables the ASIC3's DS1WM MFD cell, supported by the ds1wm driver.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This should make the code a little bit easier to read.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Since ASIC3 has to work on both PXA and S3C and since their
struct clk implementations differ, we can't register out
clocks with the clkdev mechanism (yet?).
For now we have to keep clock handling internal to this
driver and enable/disable the clocks via the
mfd_cell->enable/disable functions.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Used to configure single bits of the SDHWCTRL_SDCONF and EXTCF_RESET/SELECT
registers needed for DS1WM, MMC/SDIO and PCMCIA functionality.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The PCAP Asic as present on EZX phones is a multi function device with
voltage regulators, ADC, touch screen controller, RTC, USB transceiver,
leds controller, and audio codec.
It has two SPI ports, typically one is connected to the application
processor and another to the baseband, this driver provides read/write
functions to its registers, irq demultiplexer and ADC
queueing/abstraction.
This chip is used on a lot of Motorola phones, it was manufactured by TI
as a custom product with the name PTWL93017, later this design evolved
into the ATLAS PMIC from Freescale (MC13783).
Signed-off-by: Daniel Ribeiro <drwyrm@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This adds a core driver for the AB3100 mixed-signal circuit
found in the ST-Ericsson U300 series platforms. This driver
is a singleton proxy for all accesses to the AB3100
sub-drivers which will be merged on top of this one, RTC,
regulators, battery and system power control, vibrator,
LEDs, and an ALSA codec.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Reviewed-by: Mike Rapoport <mike@compulab.co.il>
Reviewed-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The defines and typedefs (hw_interrupt_type, no_irq_type, irq_desc_t) have
been kept around for migration reasons. After more than two years it's
time to remove them finally.
This patch cleans up one of the remaining users. When all such patches
hit mainline we can remove the defines and typedefs finally.
Impact: cleanup
Convert the last remaining users and remove the typedef.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add the missing MODULE_LICENSE("GPL").
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Cc: Balaji Rao <balajirrao@openmoko.org>
Cc: Andy Green <andy@openmoko.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
No impact unless someone has written additional kernel code.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Impact: Fix section mismatch.
clocks_init() has been called from twl4030_probe() which is a non-init
function. Since probing can be done anytime so clocks_init will be
called anytime too. So we mark clock_init() as non-init.
LD drivers/mfd/built-in.o
WARNING: drivers/mfd/built-in.o(.text+0x8dd9): Section mismatch in
reference from the function twl4030_probe() to the function
.init.text:clocks_init()
The function twl4030_probe() references
the function __init clocks_init().
This is often because twl4030_probe lacks a __init
annotation or the annotation of clocks_init is wrong.
Signed-off-by: Rakib Mullick <rakib.mullick@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This includes the USB current limit status override which is used in the
power management driver.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/davej/cpufreq:
[CPUFREQ] cpumask: new cpumask operators for arch/x86/kernel/cpu/cpufreq/powernow-k8.c
[CPUFREQ] cpumask: avoid playing with cpus_allowed in powernow-k8.c
[CPUFREQ] cpumask: avoid cpumask games in arch/x86/kernel/cpu/cpufreq/speedstep-centrino.c
[CPUFREQ] cpumask: avoid playing with cpus_allowed in speedstep-ich.c
[CPUFREQ] powernow-k8: get drv data for correct CPU
[CPUFREQ] powernow-k8: read P-state from HW
[CPUFREQ] reduce scope of ACPI_PSS_BIOS_BUG_MSG[]
[CPUFREQ] Clean up convoluted code in arch/x86/kernel/tsc.c:time_cpufreq_notifier()
[CPUFREQ] minor correction to cpu-freq documentation
[CPUFREQ] powernow-k8.c: mess cleanup
[CPUFREQ] Only set sampling_rate_max deprecated, sampling_rate_min is useful
[CPUFREQ] powernow-k8: Set transition latency to 1 if ACPI tables export 0
[CPUFREQ] ondemand: Uncouple minimal sampling rate from HZ in NO_HZ case
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6:
[SCSI] aic79xx: make driver respect nvram for IU and QAS settings
[SCSI] don't attach ULD to Dell Universal Xport
[SCSI] lpfc 8.3.3 : Update driver version to 8.3.3
[SCSI] lpfc 8.3.3 : Add support for Target Reset handler entrypoint
[SCSI] lpfc 8.3.3 : Fix a couple of spin_lock and memory issues and a crash
[SCSI] lpfc 8.3.3 : FC/FCOE discovery fixes
[SCSI] lpfc 8.3.3 : Fix various SLI-3 vs SLI-4 differences
[SCSI] qla2xxx: Resolve a performance issue in interrupt
[SCSI] cnic, bnx2i: Fix build failure when CONFIG_PCI is not set.
[SCSI] nsp_cs: time_out reaches -1
[SCSI] qla2xxx: fix printk format warnings
[SCSI] ncr53c8xx: div reaches -1
[SCSI] compat: don't perform unneeded copy in sg_io code
[SCSI] zfcp: Update FC pass-through support
[SCSI] zfcp: Add FC pass-through support
[SCSI] FC Pass Thru support
* 'linux-next' of git://git.infradead.org/ubi-2.6: (21 commits)
UBI: add reboot notifier
UBI: handle more error codes
UBI: fix multiple spelling typos
UBI: fix kmem_cache_free on error patch
UBI: print amount of reserved PEBs
UBI: improve messages in the WL worker
UBI: make gluebi a separate module
UBI: remove built-in gluebi
UBI: add notification API
UBI: do not switch to R/O mode on read errors
UBI: fix and clean-up error paths in WL worker
UBI: introduce new constants
UBI: fix race condition
UBI: minor serialization fix
UBI: do not panic if volume check fails
UBI: add dump_stack in checking code
UBI: fix races in I/O debugging checks
UBI: small debugging code optimization
UBI: improve debugging messages
UBI: re-name volumes_mutex to device_mutex
...
This causes an issue since we fixed the drm mappings to do the right thing,
so its just a copy and pasto.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It is generally agreed that it would be beneficial for u64 to be an
unsigned long long on all architectures. ia64 (in common with several
other 64-bit architectures) currently uses unsigned long. Migrating
piecemeal is too painful; this giant patch fixes all compilation warnings
and errors that come as a result of switching to use int-ll64.h.
Note that userspace will still see __u64 defined as unsigned long. This
is important as it affects C++ name mangling.
[Updated by Tony Luck to change efi.h:efi_freemem_callback_t to use
u64 for start/end rather than unsigned long]
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Fix kernel-doc parameter name in phy_device.c.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix up remaining drivers returning a magic or an errno value from their
ndo_start_xmit() functions that were missed in the first pass:
- isdn_net: missed conversion
- bpqether: missed conversion: skb is freed, so return NETDEV_TX_OK
- hp100: intention appears to be to resubmit skb once resources are
available, but due to no queue handling it is dropped for now.
- lapbether: skb is freed, so return NETDEV_TX_OK
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Enabled SRIOV support in the driver.
- Call __vxge_hw_verify_pci_e_info() for the PF only. This function
verifies the negotiated link width and current link speed in the
Link Status Register (offset 12h) which are reserved fields for VFs
as per the SRIOV specification, section 3.5.8.
- Implemented David Miller's comment to remove the #ifdef CONFIG_PCI_IOV as
these intefaces have NOP versions declared when the defintion is not set.
Signed-off-by: Sivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: Rastapur Santosh <santosh.rastapur@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The octeon-ethernet driver supports the sgmii, rgmii, spi, and xaui
ports present on the Cavium OCTEON family of SOCs. These SOCs are
multi-core mips64 processors with existing support over in arch/mips.
The driver files can be categorized into three basic groups:
1) Register definitions, these are named cvmx-*-defs.h
2) Main driver code, these have names that don't start cvmx-.
3) Interface specific functions and other utility code, names starting
with cvmx-
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch adds support for the integrated RNG of the TX4939 SoC.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Acked-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch adds support for the integrated DMAC of the TXx9 family.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Unify i2c camera device platform data to point to struct soc_camera_link
for a smooth transition to soc-camera as a platform driver.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Modify the CMT and TMU drivers to disable interrupts when
disabling the timer. Only using start/stop bits is not
enough.
This fixes a bootup hang on Migo-R when the CMT is replaced
by TMU for clockevents but the CMT keeps on delivering irqs
even though the timer start bit is off.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* 'next-i2c' of git://aeryn.fluff.org.uk/bjdooks/linux:
i2c-stu300: Make driver depend on MACH_U300
i2c-s3c2410: use resource_size()
i2c: Use resource_size macro
i2c: ST DDC I2C U300 bus driver v3
i2c-bfin-twi: pull in io.h for ioremap()
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon: switch to using late_initcall
radeon legacy chips: tv dac bg/dac adj updates
drm/radeon: introduce kernel modesetting for radeon hardware
drm: Add the TTM GPU memory manager subsystem.
drm: Memory fragmentation from lost alignment blocks
drm/radeon: fix mobility flags on new PCI IDs.
* akpm: (182 commits)
fbdev: bf54x-lq043fb: use kzalloc over kmalloc/memset
fbdev: *bfin*: fix __dev{init,exit} markings
fbdev: *bfin*: drop unnecessary calls to memset
fbdev: bfin-t350mcqb-fb: drop unused local variables
fbdev: blackfin has __raw I/O accessors, so use them in fb.h
fbdev: s1d13xxxfb: add accelerated bitblt functions
tcx: use standard fields for framebuffer physical address and length
fbdev: add support for handoff from firmware to hw framebuffers
intelfb: fix a bug when changing video timing
fbdev: use framebuffer_release() for freeing fb_info structures
radeon: P2G2CLK_ALWAYS_ONb tested twice, should 2nd be P2G2CLK_DAC_ALWAYS_ONb?
s3c-fb: CPUFREQ frequency scaling support
s3c-fb: fix resource releasing on error during probing
carminefb: fix possible access beyond end of carmine_modedb[]
acornfb: remove fb_mmap function
mb862xxfb: use CONFIG_OF instead of CONFIG_PPC_OF
mb862xxfb: restrict compliation of platform driver to PPC
Samsung SoC Framebuffer driver: add Alpha Channel support
atmel-lcdc: fix pixclock upper bound detection
offb: use framebuffer_alloc() to allocate fb_info struct
...
Manually fix up conflicts due to kmemcheck in mm/slab.c
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The remove member of the platform_driver bfin_t350mcqb_driver should use
__devexit_p() to refer to the remove function, and that function should
get __devexit markings. Likewise, the probe function should be marked
with __devinit and not __init.
Also, module_init() functions should be marked with __init rather than
__devinit.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Bill Pemberton
Linus Torvalds
Rodolfo Giometti
Jack Steiner
Neil Horman
Daniel Mack
GeunSik Lim
Mike Frysinger
Harry Ciao
Michael Buesch
Jiri Slaby
Adriano dos Santos Fernandes
Nate Case
Daniel Silverstone
Atsushi Nemoto
Wolfgang Grandegger
Wolfram Sang
Joakim Tjernlund
Torsten Ertbjerg Rasmussen
Jiri Pirko
Daniel Ribeiro
Anton Vorontsov
David Brownell
Roel Kluin
Dhananjay Phadke
Eric Dumazet
Thomas Mingarelli
Wim Van Sebroeck
Denis V. Lunev
Séguier Régis
Rafael J. Wysocki
chaithrika@ti.com
Stephen Hemminger
françois romieu
Haiying Wang
Grant Likely
NeilBrown
Dan Williams
SandeepKsinha
Andre Noll
Matthew Wilcox
Samuel Ortiz
Philipp Zabel
Mark Brown
Linus Walleij
Thomas Gleixner
Adrian Bunk
Rakib Mullick
Dave Airlie
Tony Luck
Matthew Wilcox
Randy Dunlap
Patrick McHardy
Sivakumar Subramani
David Daney
David S. Miller
Paul Mundt
Guennadi Liakhovetski
Magnus Damm