Although the extended tables are theoretically a completely orthogonal
feature to PASID and anything else that *uses* the newly-available bits,
some of the early hardware has problems even when all we do is enable
them and use only the same bits that were in the old context tables.
For now, there's no motivation to support extended tables unless we're
going to use PASID support to do SVM. So just don't use them unless
PASID support is advertised too. Also add a command-line bailout just in
case later chips also have issues.
The equivalent problem for PASID support has already been fixed with the
upcoming VT-d spec update and commit bd00c606a ("iommu/vt-d: Change
PASID support to bit 40 of Extended Capability Register"), because the
problematic platforms use the old definition of the PASID-capable bit,
which is now marked as reserved and meaningless.
So with this change, we'll magically start using ECS again only when we
see the new hardware advertising "hey, we have PASID support and we
actually tested it this time" on bit 40.
The VT-d hardware architect has promised that we are not going to have
any reason to support ECS *without* PASID any time soon, and he'll make
sure he checks with us before changing that.
In the future, if hypothetical new features also use new bits in the
context tables and can be seen on implementations *without* PASID support,
we might need to add their feature bits to the ecs_enabled() macro.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The Hardware Spinlock device on atlas7 provides hardware assistance
for synchronization between the multiple processors in the system
(dual Cortex-A7, CAN bus Cortex-M3 and audio DSP).
This patch adds the DT bindings information for this hwspinlock
module.
Reviewed-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Wei Chen <wei.chen@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
This change creates a new input handler called "leds" that exports LEDs on input
devices as standard LED class devices in sysfs and allows controlling their
state via sysfs or via any of the standard LED triggers. This allows to
re-purpose and reassign LDEs on the keyboards to represent states other
than the standard keyboard states (CapsLock, NumLock, etc).
The old API of controlling input LEDs by writing into /dev/input/eventX
devices is still present and will take precedence over accessing via LEDs
subsystem (i.e. it may override state set by a trigger). If input device is
"grabbed" then requests coming through LED subsystem will be ignored.
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Tested-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
* zte/soc:
ARM: zx: Add basic defconfig support for ZX296702
ARM: dts: zx: add an initial zx296702 dts and doc
clk: zx: add clock support to zx296702
dt-bindings: Add #defines for ZTE ZX296702 clocks
Add initial dts file and document for ZX296702 and board ZX296702-AD1.
More peripherals will be added later.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
- add failure(exception) handling
: of_iomap(), of_find_device_by_node() and kstrdup()
- add common poweroff to use PS_HOLD based for all of exynos SoCs
- add exnos_get/set_boot_addr() helper
- constify platform_device_id and irq_domain_ops
- get current parent clock for power domain on/off
- use core_initcall to register power domain driver
- make exynos_core_restart() less verbose
- add support coupled CPUidle for exynos3250
- fix exynos_boot_secondary() return value on timeout
- fix clk_enable() in s3c24xx adc
- fix missing of_node_put() for power domains
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=LybA
-----END PGP SIGNATURE-----
Merge tag 'samsung-mach-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/soc
Samsung updates for v4.2
- add failure(exception) handling
: of_iomap(), of_find_device_by_node() and kstrdup()
- add common poweroff to use PS_HOLD based for all of exynos SoCs
- add exnos_get/set_boot_addr() helper
- constify platform_device_id and irq_domain_ops
- get current parent clock for power domain on/off
- use core_initcall to register power domain driver
- make exynos_core_restart() less verbose
- add support coupled CPUidle for exynos3250
- fix exynos_boot_secondary() return value on timeout
- fix clk_enable() in s3c24xx adc
- fix missing of_node_put() for power domains
* tag 'samsung-mach-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung: (301 commits)
ARM: EXYNOS: register power domain driver from core_initcall
ARM: EXYNOS: use PS_HOLD based poweroff for all supported SoCs
ARM: SAMSUNG: Constify platform_device_id
ARM: EXYNOS: Constify irq_domain_ops
ARM: EXYNOS: add coupled cpuidle support for Exynos3250
ARM: EXYNOS: add exynos_get_boot_addr() helper
ARM: EXYNOS: add exynos_set_boot_addr() helper
ARM: EXYNOS: make exynos_core_restart() less verbose
ARM: EXYNOS: fix exynos_boot_secondary() return value on timeout
ARM: EXYNOS: Get current parent clock for power domain on/off
ARM: SAMSUNG: fix clk_enable() WARNing in S3C24XX ADC
ARM: EXYNOS: Add missing of_node_put() when parsing power domains
ARM: EXYNOS: Handle of_find_device_by_node() and kstrdup() failures
ARM: EXYNOS: Handle of of_iomap() failure
Linux 4.1-rc4
....
Add support of Marvell NFC chip controlled over UART
Signed-off-by: Vincent Cuissard <cuissard@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
- use labels for overriding nodes for all of exynos stuff
(by Krzysztof Kozlowski)
- add sysmmu nodes for exynos SoCs (by Marek Szyprowski)
- for exynos5422-odroidxu3
: enalbe wake alarm of S2MPS11 RTC
: Hook up PWM and use it for LEDs
: add support for Odroid XU3 Lite
- remove duplicated i2c7 for exynos5250-snow
- add JPEG codec nodes for exynos5420
- add vendor prefix for Hardkernel
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=ZQaR
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt-4' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/dt
Samsung another DT udpates for v4.2
- use labels for overriding nodes for all of exynos stuff
(by Krzysztof Kozlowski)
- add sysmmu nodes for exynos SoCs (by Marek Szyprowski)
- for exynos5422-odroidxu3
: enalbe wake alarm of S2MPS11 RTC
: Hook up PWM and use it for LEDs
: add support for Odroid XU3 Lite
- remove duplicated i2c7 for exynos5250-snow
- add JPEG codec nodes for exynos5420
- add vendor prefix for Hardkernel
* tag 'samsung-dt-4' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung: (33 commits)
ARM: dts: add sysmmu nodes for exynos5420
ARM: dts: add sysmmu nodes for exynos5250
ARM: dts: add sysmmu nodes for exynos4415
ARM: dts: add sysmmu nodes for exynos3250
ARM: dts: add sysmmu nodes for exynos4
ARM: dts: Add Odroid XU3 Lite support
of: Add vendor prefix for Hardkernel
ARM: dts: odroidxu3: Enable wake alarm of S2MPS11 RTC
ARM: dts: exynos5420: add nodes for jpeg codec
ARM: dts: s3c2416: Use labels for overriding nodes in SMDK2416
ARM: dts: s3c2416: Add labels to S3C2416 nodes
ARM: dts: Use labels for overriding nodes in exynos5422-odroidxu3
ARM: dts: Use labels for overriding nodes in exynos5440 boards
ARM: dts: Use labels for overriding nodes in exynos5420-smdk5420
ARM: dts: Use labels for overriding nodes in exynos542x
ARM: dts: Use labels for overriding nodes in exynos5420-arndale-octa
ARM: dts: Remove duplicated I2C7 nodes in exynos5250-snow
ARM: dts: Use labels for overriding nodes in exynos5250
ARM: dts: Add labels to exynos5 nodes
ARM: dts: exynos5422-odroidxu3: Hook up PWM and use it for LEDs
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVa7zvAAoJEHm+PkMAQRiGtfMIAILs3sxFtrC1hApgcfRLF/7z
K34bwTRqErzqUO/orTwakEr9kSIpIL0zIPSryTCOTPZLfMGkQjhHXO3KR/DSbbTV
MZ8y/BM/yelFA/Np+1LjbiYjTNRnTRvCoaQihkIH8Rn02g7ob9HyL4gIGKpuGFcZ
04GacL2cgChqsRSACdNef948jCoJXKgcuDpe39DXphDWZnBKNZ3HFuJ6bryGJf9A
1/eCI4is85BNwKPemQUYR0xx83UIzDfrghatZP2mOCDDSA2MNg8HNxLTd12LGoQD
tfgX4B7aftzW9Y7GSEDfZ0IKm2NRzgPmCVj6PjVR/iI0lIK4Aq0Z/lDJxxEq3XQ=
=AJM5
-----END PGP SIGNATURE-----
Merge tag 'v4.1-rc6' into next/dt
Linux 4.1-rc6
Conflicts:
arch/arm/boot/dts/zynq-7000.dtsi
Resolution summary:
Mainline had an earlier version of the commit, resolve in favor of the
newer patch in next/dt branch.
- for exyos3250
: use s3c6410-rtc instead of exynos3250-rtc
: add JPEG codec node and support it on exynos3250-rinato
: use s3c-rtc clock id for exynos3250-rinato and monk boards
- for exynos4
: add JPEG codec node and syscon property to MIPI DPHY
: remove obsolete MIPI DPHY reg property
: enable s3c-rtc on exynos4412-trats2
- for exynos5
: add syscon property to MIPI DPHY for exynos5420
: enable s3c-rtc on exynos5420-arndale-octa
: add missing irq pinctrl for max77686 on exynos5250-smdk5250
: clk: add bindings for 32kHz clocks from s2mps11
: fix pinctrl for s2mps11-irq on exynos5420-arndale-octa
- for exynos5422-odroidxu3
: add mmc detect gpio and LEDs
: add HS400 support, simple-audio-card and rtc_src clock
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=bWPy
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt-3' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/dt
Samsung DT updates for v4.2
- for exyos3250
: use s3c6410-rtc instead of exynos3250-rtc
: add JPEG codec node and support it on exynos3250-rinato
: use s3c-rtc clock id for exynos3250-rinato and monk boards
- for exynos4
: add JPEG codec node and syscon property to MIPI DPHY
: remove obsolete MIPI DPHY reg property
: enable s3c-rtc on exynos4412-trats2
- for exynos5
: add syscon property to MIPI DPHY for exynos5420
: enable s3c-rtc on exynos5420-arndale-octa
: add missing irq pinctrl for max77686 on exynos5250-smdk5250
: clk: add bindings for 32kHz clocks from s2mps11
: fix pinctrl for s2mps11-irq on exynos5420-arndale-octa
- for exynos5422-odroidxu3
: add mmc detect gpio and LEDs
: add HS400 support, simple-audio-card and rtc_src clock
* tag 'samsung-dt-3' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: dts: Add syscon property to the MIPI DPHY for exynos4415
ARM: dts: Remove obsolete MIPI DPHY 'reg' property for exynos4
ARM: dts: Use last parent for clocks during power domain on/off
ARM: dts: add support JPEG codec for exynos3250-rinato
ARM: dts: support simple-audio-card for exynos5420 and exynos5422-odroidxu3
ARM: dts: add jpeg-codec node for exynos4 and exynos4x12
ARM: dts: Enable S3C RTC on exynos4412-trats2 and exynos5420-arndale-octa
ARM: dts: Use define for s3c-rtc clock id for exynos3250-monk
ARM: dts: Use define for s3c-rtc clock id for exynos3250-rinato
ARM: dts: Use s3c6410-rtc instead of exynos3250-rtc for exynos3250/4415
ARM: dts: add 'rtc_src' clock to rtc node for exynos5422-odroidxu3
clk: samsung: Add bindings for 32kHz clocks from s2mps11
ARM: dts: fix pinctrl for s2mps11-irq on exynos5420-arndale-octa
ARM: dts: Add syscon property to the MIPI phy in exynos5420
ARM: dts: Add HS400 support for exynos5422-odroidxu3
ARM: dts: Add LEDs for exynos5422-odroidxu3
ARM: dts: add mmc detect gpio for exynos5422-odroidxu3
ARM: dts: add JPEG codec device node for exynos3250
ARM: dts: Add missing irq pinctrl for max77686 on smdk5250
If a cache metadata operation fails (e.g. transaction commit) the
cache's metadata device will abort the current transaction, set a new
needs_check flag, and the cache will transition to "read-only" mode. If
aborting the transaction or setting the needs_check flag fails the cache
will transition to "fail-io" mode.
Once needs_check is set the cache device will not be allowed to
activate. Activation requires write access to metadata. Future work is
needed to add proper support for running the cache in read-only mode.
Once in fail-io mode the cache will report a status of "Fail".
Also, add commit() wrapper that will disallow commits if in read_only or
fail mode.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Some targets (eg: msm8994) use the pinctrl framework to configure
interface pins. This change adds support for initialization and
pinctrl active/sleep state control for the HDMI driver.
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
There are different types of PHY from one chipset to another, while
the DSI host controller is relatively consistent across platforms.
Also, the PLL inside PHY is providing the source of DSI byte and
pixel clocks, which are used by DSI host controller. Separated devices
for clock provider and clock consumer make DSI driver better fit into
common clock framework.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
A new API call has been introduced which allows channels to be
requested by name. This new call uses the 'mbox-names' property,
so users need no further discouragement from supplying it.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Ethernet AVB includes an Gigabit Ethernet controller (E-MAC) that is basically
compatible with SuperH Gigabit Ethernet E-MAC. Ethernet AVB has a dedicated
direct memory access controller (AVB-DMAC) that is a new design compared to the
SuperH E-DMAC. The AVB-DMAC is compliant with 3 standards formulated for IEEE
802.1BA: IEEE 802.1AS timing and synchronization protocol, IEEE 802.1Qav real-
time transfer, and the IEEE 802.1Qat stream reservation protocol.
The driver only supports device tree probing, so the binding document is
included in this patch.
Based on the original patches by Mitsuhiro Kimura.
Signed-off-by: Mitsuhiro Kimura <mitsuhiro.kimura.kc@renesas.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds create/remove window ioctls to create and remove DMA windows.
sPAPR defines a Dynamic DMA windows capability which allows
para-virtualized guests to create additional DMA windows on a PCI bus.
The existing linux kernels use this new window to map the entire guest
memory and switch to the direct DMA operations saving time on map/unmap
requests which would normally happen in a big amounts.
This adds 2 ioctl handlers - VFIO_IOMMU_SPAPR_TCE_CREATE and
VFIO_IOMMU_SPAPR_TCE_REMOVE - to create and remove windows.
Up to 2 windows are supported now by the hardware and by this driver.
This changes VFIO_IOMMU_SPAPR_TCE_GET_INFO handler to return additional
information such as a number of supported windows and maximum number
levels of TCE tables.
DDW is added as a capability, not as a SPAPR TCE IOMMU v2 unique feature
as we still want to support v2 on platforms which cannot do DDW for
the sake of TCE acceleration in KVM (coming soon).
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
[aw: for the vfio related changes]
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The existing implementation accounts the whole DMA window in
the locked_vm counter. This is going to be worse with multiple
containers and huge DMA windows. Also, real-time accounting would requite
additional tracking of accounted pages due to the page size difference -
IOMMU uses 4K pages and system uses 4K or 64K pages.
Another issue is that actual pages pinning/unpinning happens on every
DMA map/unmap request. This does not affect the performance much now as
we spend way too much time now on switching context between
guest/userspace/host but this will start to matter when we add in-kernel
DMA map/unmap acceleration.
This introduces a new IOMMU type for SPAPR - VFIO_SPAPR_TCE_v2_IOMMU.
New IOMMU deprecates VFIO_IOMMU_ENABLE/VFIO_IOMMU_DISABLE and introduces
2 new ioctls to register/unregister DMA memory -
VFIO_IOMMU_SPAPR_REGISTER_MEMORY and VFIO_IOMMU_SPAPR_UNREGISTER_MEMORY -
which receive user space address and size of a memory region which
needs to be pinned/unpinned and counted in locked_vm.
New IOMMU splits physical pages pinning and TCE table update
into 2 different operations. It requires:
1) guest pages to be registered first
2) consequent map/unmap requests to work only with pre-registered memory.
For the default single window case this means that the entire guest
(instead of 2GB) needs to be pinned before using VFIO.
When a huge DMA window is added, no additional pinning will be
required, otherwise it would be guest RAM + 2GB.
The new memory registration ioctls are not supported by
VFIO_SPAPR_TCE_IOMMU. Dynamic DMA window and in-kernel acceleration
will require memory to be preregistered in order to work.
The accounting is done per the user process.
This advertises v2 SPAPR TCE IOMMU and restricts what the userspace
can do with v1 or v2 IOMMUs.
In order to support memory pre-registration, we need a way to track
the use of every registered memory region and only allow unregistration
if a region is not in use anymore. So we need a way to tell from what
region the just cleared TCE was from.
This adds a userspace view of the TCE table into iommu_table struct.
It contains userspace address, one per TCE entry. The table is only
allocated when the ownership over an IOMMU group is taken which means
it is only used from outside of the powernv code (such as VFIO).
As v2 IOMMU supports IODA2 and pre-IODA2 IOMMUs (which do not support
DDW API), this creates a default DMA window for IODA2 for consistency.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
[aw: for the vfio related changes]
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Given Linus announced a 4.8rc coming up, hopefully time for one more
lot of IIO patches this cycle. Some of these are actually
improvements / fixes for patches earlier in the cycle.
New device support
* st_accel driver - support devices with 8 bit channels.
Cleanup
* A general cleanup of the iio tools under /tools/ from Hartmut.
I'm more than a little embarassed by how bad some of these were! Are well,
much more refined and less bug prone now.
These cover lots of stuff like unhandled error returns, memory leaks as
well as general refactoring to tidy the code up.
* iio_simple_dummy - fix memory leaks in the init functions, drop some
pointless error returns from functions that never generate errors and
make the module parameter explicitly unsigned.
* More buffer handling reworks from Lars-Peter, this time targetting hardware
buffers (a little used corner that looks likely to get more use in the near
future). Specifically:
- Always compute the masklength as inkernel buffer users may need it.
- Add a means of labeling which buffer modes a given buffer implementation
supports.
- In the case of hardware buffers, require strict scan matching rather than
matching to a superset. Currently the demux is bypassed by these drivers
(this may well not change for efficiency reasons) so allowing a superset
of channels to be selected would otherwise lead to more data than requested
confusing userspace.
Driver funcationality improvments
* mmc35240 - adds a compensation to the raw values as borrowed form Memsic's
own input driver.
* mma8452
- event support
- event debouncing
- high pass filter configuration
- triggers
* vf610 - allow conversion mode to be adjusted
Fixlets
* mmc35240
- Off by one error that by coincidence had no real effect.
- i2c_device_name should be lowercase.
- Lack of null terminator at end of attributes array.
- Avoid computing the fractional part of the magnetic field by moving
the scaling into userspace where floating point is available to simplify
the maths.
- Use a smaller sleep before assuming the measurement is done. This is
safe and improves the possible polling rate.
- Fix sensitivity on z-axis - datasheet disagrees with Memsic's releasedd
code and the value used in the code seems to be correct.
* stk3310 - make a local variable signed to ensure error handling works.
* twl4030
- fix calculation of the temperature sense current - bug unlikely
to have ever been noticed as the difference is small.
- Fix errors in descriptions.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=sNVc
-----END PGP SIGNATURE-----
Merge tag 'iio-for-v4.2c' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Third round of new IIO drivers, cleanups and functionality for the 4.2 cycle.
Given Linus announced a 4.8rc coming up, hopefully time for one more
lot of IIO patches this cycle. Some of these are actually
improvements / fixes for patches earlier in the cycle.
New device support
* st_accel driver - support devices with 8 bit channels.
Cleanup
* A general cleanup of the iio tools under /tools/ from Hartmut.
I'm more than a little embarassed by how bad some of these were! Are well,
much more refined and less bug prone now.
These cover lots of stuff like unhandled error returns, memory leaks as
well as general refactoring to tidy the code up.
* iio_simple_dummy - fix memory leaks in the init functions, drop some
pointless error returns from functions that never generate errors and
make the module parameter explicitly unsigned.
* More buffer handling reworks from Lars-Peter, this time targetting hardware
buffers (a little used corner that looks likely to get more use in the near
future). Specifically:
- Always compute the masklength as inkernel buffer users may need it.
- Add a means of labeling which buffer modes a given buffer implementation
supports.
- In the case of hardware buffers, require strict scan matching rather than
matching to a superset. Currently the demux is bypassed by these drivers
(this may well not change for efficiency reasons) so allowing a superset
of channels to be selected would otherwise lead to more data than requested
confusing userspace.
Driver funcationality improvments
* mmc35240 - adds a compensation to the raw values as borrowed form Memsic's
own input driver.
* mma8452
- event support
- event debouncing
- high pass filter configuration
- triggers
* vf610 - allow conversion mode to be adjusted
Fixlets
* mmc35240
- Off by one error that by coincidence had no real effect.
- i2c_device_name should be lowercase.
- Lack of null terminator at end of attributes array.
- Avoid computing the fractional part of the magnetic field by moving
the scaling into userspace where floating point is available to simplify
the maths.
- Use a smaller sleep before assuming the measurement is done. This is
safe and improves the possible polling rate.
- Fix sensitivity on z-axis - datasheet disagrees with Memsic's releasedd
code and the value used in the code seems to be correct.
* stk3310 - make a local variable signed to ensure error handling works.
* twl4030
- fix calculation of the temperature sense current - bug unlikely
to have ever been noticed as the difference is small.
- Fix errors in descriptions.
- Add device tree for i.MX7D SoC and imx7d-sdb board
- New i.MX6 board support: Armadeus Systems APF6, Gateworks GW5510,
and aristainetos2 boards
- Change LVDS to use simple-panel for nitrogen6x and sabrelite boards
- Add Wifi/Bluetooth devices support for cubox-i board
- Remove unused regulators and correct OTG roles setting for
imx6sl-warp board
- Add I2C support for imx23-olinuxino board
- Move imx6qdl HDMI device to a better place
- Add power-domain for imx6qdl CODA device
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVb7iWAAoJEFBXWFqHsHzOIGEIAJjoZ+80PKH6+obh7gCuEkIx
MkZobKxYyRRh+wD+7NZEqSPMYxBW6eUCYGCCy+f/4xjmlIfHkp/DaaCeIU0EZItl
GU1ZE7qg6kWGbamun7zXcrg1cZ+bFOpQ926isETurL8LC2+PLm6OSg1pl6hwjqpA
rGzY2aEH5Lke6wDN0cMus0ApMlIQ8HpOLABtqosuzUWclyZBmoxBQshbW8ztzS3Y
pjpRfAHS91+0vZpoqmULTc/ENbTToNYk5NxJgMMDigkz1Gqp0Ni+rxmDmRPayo09
/Nq4VHDT+wx3CSf6nC9YIrabxrBMpvTky2jWOAJ4OxMFjT0xle3XISGRoa1ifqo=
=PbGi
-----END PGP SIGNATURE-----
Merge tag 'imx-dt-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt
The i.MX device tree changes for 4.2:
- Add device tree for i.MX7D SoC and imx7d-sdb board
- New i.MX6 board support: Armadeus Systems APF6, Gateworks GW5510,
and aristainetos2 boards
- Change LVDS to use simple-panel for nitrogen6x and sabrelite boards
- Add Wifi/Bluetooth devices support for cubox-i board
- Remove unused regulators and correct OTG roles setting for
imx6sl-warp board
- Add I2C support for imx23-olinuxino board
- Move imx6qdl HDMI device to a better place
- Add power-domain for imx6qdl CODA device
* tag 'imx-dt-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (24 commits)
ARM: dts: imx6dl: add imx6dl gpt specific compatible string
ARM: dts: imx6: add DT for aristainetos2 board
ARM: dts: cubox-i/hummingboard: Fix the license text
ARM: dts: sabrelite: use simple-panel instead of display-timings for LVDS0
ARM: dts: nitrogen6x: use simple-panel instead of display-timings for LVDS0
ARM: dts: add imx7d-sdb support
ARM: dts: add imx7d soc dtsi file
ARM: dts: Armadeus Systems APF6 family support (i.MX6)
ARM: dts: vf610: Nomenclature fixup for PTC12 pin used in RMII mode.
ARM: dts: cubox-i: add support for Broadcom Wifi/Bluetooth devices
Document: dt: binding: imx: update document for imx7d support
ARM: dts: imx6qdl: Add power-domain phandle to CODA device node
ARM: dts: Gateworks GW5510 support (i.MX6)
ARM: dts: imx6sl-warp: Fix OTG roles
ARM: dts: imx6sl-warp: Remove USB regulators
ARM: dts: imx6sl-warp: Remove unused regulator
ARM: dts: add pinfunc include file to support imx7d
ARM: mxs: fix in tree users of ssd1306
ARM: dts: imx6qdl-hummingboard: Add PCIe support
ARM: dts: imx23-olinuxino: Add i2c support
...
These options make it possible to overwrites the data and instruction
prefetching behavior of the arm pl310 cache controller.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch extends LED Flash class documention by
the description of interactions with v4l2-flash sub-device.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
The big thing this release has been Liam's addition of topology support
to the core. We've also seen quite a bit of driver work and the
continuation of Lars' refactoring for component support.
- Support for loading ASoC topology maps from firmware, intended to be
used to allow self-describing DSP firmware images to be built which
can map controls added by the DSP to userspace without the kernel
needing to know about individual DSP firmwares.
- Lots of refactoring to avoid direct access to snd_soc_codec where
it's not needed supporting future refactoring.
- Big refactoring and cleanup serieses for the Wolfson ADSP and TI
TAS2552 drivers.
- Support for TI TAS571x power amplifiers.
- Support for Qualcomm APQ8016 and ZTE ZX296702 SoCs.
- Support for x86 systems with RT5650 and Qualcomm Storm.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVddV1AAoJECTWi3JdVIfQQQsH/RG3lgOeot5jLWMsxJSKChEl
KI+aaMcOw6Dj2LDccN8i6vUp8q44cKSXIc7lGLOzJW4K+OydCCGAvE+sJGyRE1dd
yOHwcbvjJi4zFlt01RZchJ/Wa/S6zFucl5N9HxWsV4bEtfAA59IuhJLtospUlwsA
mf9mpvSdeUAeh3lM2+AqAbXhTo6dYfD5ky5nrtpAkZjG8gqUG0u8Tpauja0lLcHi
72/3EkzKR6KHaefyPw3LdN+/H/YK79uHCVcctZnQg5xUUymcO16ReoTxKwV9cnDb
lBJ6wO8RpUAO9evoG2Yj/l4p+czDCm5VkHMq0nPklHVRh7s/2PwKfox1aw4Pumg=
=wolq
-----END PGP SIGNATURE-----
Merge tag 'asoc-v4.2' into asoc-rt5645
ASoC: Updates for v4.2
The big thing this release has been Liam's addition of topology support
to the core. We've also seen quite a bit of driver work and the
continuation of Lars' refactoring for component support.
- Support for loading ASoC topology maps from firmware, intended to be
used to allow self-describing DSP firmware images to be built which
can map controls added by the DSP to userspace without the kernel
needing to know about individual DSP firmwares.
- Lots of refactoring to avoid direct access to snd_soc_codec where
it's not needed supporting future refactoring.
- Big refactoring and cleanup serieses for the Wolfson ADSP and TI
TAS2552 drivers.
- Support for TI TAS571x power amplifiers.
- Support for Qualcomm APQ8016 and ZTE ZX296702 SoCs.
- Support for x86 systems with RT5650 and Qualcomm Storm.
Modify the RT5645 driver to parse platform data from device tree.
Write a DT binding document to describe those properties.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds bindings for apq8016 sbc machine driver.
APQ8016 has 4 MI2S which can be configured to different sinks like
internal codec/external codec, this connection and various parameters
are controlled via 2 iomux registers.
Acked-by: Kenneth Westfield <kwestfie@codeaurora.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The Marvell Armada 38x SoC introduce new features to the XOR engine,
especially the fact that the engine mode (MEMCPY/XOR/PQ/etc) can be part of
the descriptor and not set through the controller registers.
This new feature allows mixing of different commands (even PQ) on the same
channel/chain without the need to stop the engine to reconfigure the engine
mode.
Refactor the driver to be able to use that new feature on the Armada 38x,
while keeping the old behaviour on the older SoCs.
Signed-off-by: Lior Amsalem <alior@marvell.com>
Reviewed-by: Ofer Heifetz <oferh@marvell.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The commit edd4ab0559 ("power: max17042_battery: add HEALTH and TEMP_*
properties support") added support for setting voltage and temperature
thresholds with platform data. For DeviceTree default of 0 was always
used.
This caused reporting battery health always as over voltage or
over heated.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Fixes: edd4ab0559 ("power: max17042_battery: add HEALTH and TEMP_* properties support")
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Adding support for i2c controller driver for Broadcom settop
SoCs.
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
[wsa: removed superfluous owner in platform_driver]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
add a new value "atmel,sama5d2-i2c" for the "compatible" property.
add a new optional property "atmel,fifo-size" to enable FIFO support when
available.
add missing optional properties "dmas" and "dma-names".
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The Armada 39x SoC family has grown a new variant, the Armada 395,
which sits between the Armada 390 and Armada 398 in terms of
features. This commit adds support for this additional variant to the
Armada 39x pinctrl driver.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The latest version of the Armada 39x datasheet documents several new
SATA related functions on various MPP pins. This commit adds the
description of these new functions to the Armada 39x pinctrl driver as
well as to its DT binding documentation.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The latest version of the Armada 39x datasheet documents several new
PCIe related functions on various MPP pins. This commit adds the
description of these new functions to the Armada 39x pinctrl driver as
well as to its DT binding documentation.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The latest version of the Armada 38x datasheet documents several new
PTP related functions on various MPP pins. This commit adds the
description of these new functions to the Armada 38x pinctrl driver as
well as to its DT binding documentation.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The latest version of the Armada 38x datasheet documents several new
UART1 related functions on various MPP pins. This commit adds the
description of these new functions to the Armada 38x pinctrl driver as
well as to its DT binding documentation.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The latest version of the Armada 38x datasheet documents several new
NAND related functions on various MPP pins. This commit adds the
description of these new functions to the Armada 38x pinctrl driver as
well as to its DT binding documentation.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The latest version of the Armada 38x datasheet documents several new
SATA related functions on various MPP pins. This commit adds the
description of these new functions to the Armada 38x pinctrl driver as
well as to its DT binding documentation.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The latest Armada XP datasheet documents several new DRAM related
functions on various MPPs. This commit adds the description of these
new functions in the Armada XP pinctrl driver and its DT binding
documentation.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The latest version of the Armada XP datasheet documents a new
NAND-related MPP function on MPP48, for which this commit adds
support.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The latest Armada XP datasheet documents that some of the MPP pins can
be used to access the second SPI bus, labelled 'spi1'. This commit
adds the corresponding pins in the pinctrl driver and its DT binding
documentation.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
After updating to the latest Armada XP datasheet, we discovered that
there is a second SPI bus accessible from the MPP pins, called 'spi1'.
In order to be consistent with other SoCs having two SPI busses, this
commit renames the functions of the first SPI bus to 'spi0' instead of
just 'spi'.
This commit obviously breaks the DT backward compatibility for the
people using the "spi" function name in their Device Tree.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Across all SoCs, even on Armada 370 for SPI0, the clock pin uses the
'sck' subname and not 'clk', so this commit adjusts the code and
documentation accordingly.
Since this commit only changes the subname, DT backward compatibility
is not affected.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
For consistency with the datasheet, this commit renames the VDD
function of the MPP4 pin.
While this changes the DT compatibility, it is not considered to be a
problem since this pin is unlikely to be used for anything but
debugging purposes.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There was an off-by-one in the documentation of the ge1(txd[0-3])
pins, which is fixed by this commit. Since the driver was correct, and
the subnames are anyway not used in the DT binding itself, there is no
need to push this documentation fix for stable.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This commit normalizes the naming of the Ethernet txclkout pin to be
the same accross Marvell SoCs. It is worth mentioning that the DT
binding documentation of the Armada XP was wrong for MPP12: it said
the function was ge1(txd0), while it is in fact ge1(txclkout). It is
however not really a fix worth sending to stable since it does not
change the behavior, and the driver itself was correct.
Since only the subnames are changed, DT backward compatibility is not
affected.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This commit aligns the naming of the audio 'lrclk' pin accross Marvell
SoCs.
Since only the subname is changed, the DT backward compatibility is
not affected.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This commit normalizes the naming of PCIe pins to use 'rstout' instead
of 'rstoutn' or 'rst-out'.
Since only the subnames are changed, DT compatibility is not affected.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This commit normalizes the naming of the TDM pins accross the
different Marvell SoCs. Mainly it consists in:
* Removing the 'n' from signal names: 'intn' becomes 'int' and 'rstn'
becomes 'rst'
* Renaming the main name 'tdm2c' to 'tdm' on Armada 38x.
* Change the main name 'tdm-1' to 'tdm' for one of the pins of the
Armada XP
The last two changes affect DT compatibility, but since the TDM
interface is nowhere near being supported in mainline, it should not
be considered to be a serious problem at this point.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
STMicroelectronics NFC NCI chips family is extending
with the new ST21NFCC using the AMS AS39230 RF booster.
The st21nfcb driver is relevant for this solution and
might be with future products.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
All SoCs use "nand" to designate NAND pins, only Armada 39x is using
"nd", which is not consistent. This commit fixes that by renaming the
corresponding functions.
It also changes the subnames from rbn0/rbn1 to rb0/rb1, to respect the
convention used everywhere that we don't encode the 'n' part of signal
names.
While this commit changes the main name of function, therefore
potentially breaking the DT compatibility, this is not a problem since
Armada 39x is a brand new SoC which isn't used in production yet.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This commit modifies the definition of the Device Bus interface pins
to be consistent accross SoCs. Especially, it removes the 'n'
indicators that we don't encode in the subnames of pins:
'dev(wen0)' becomes 'dev(we0)'
'dev(wen1)' becomes 'dev(we1)'
'dev(oen)' becomes 'dev(oe)'
etc.
In addition, it fixes the Armada 375 DT binding documentation, which
forgot to document the 'dev' function for MPP46, MPP57 and MPP63.
Since only the subnames are changed, this commit does not affect DT
compatibility.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In order to be consistent with the datasheet and some other SoCs, this
commit renames the SDIO pins of the Armada 39x from "sd" to "sd0".
While this changes the DT binding, this is not a problem since Armada
39x is a brand new SoC which isn't used in production yet (so now is
the right time to fix such things).
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This commit makes the naming of SATA related MPP functions consistent
accross SoCs by adjusting the Armada 39x definition to use "prsnt"
instead of "present".
Since only the subnames are changed, the DT binding is not modified at
all.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This commit makes the dram functions naming (both the name and
subname) consistent accross SoC, by using:
dram(vttctrl)
dram(deccerr)
in all Marvell SoCs.
Due to the change to the name, it changes the DT binding, but these
functions are not used by any in-tree Device Tree file, and are very
unlikely to be used by anyone.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The subnames are purely informative, but it's nicer when they match
accross SoCs. This commit adjusts the Armada 375, Armada 38x and
Armada 39x MPP definitions so that the subnames of the PTP pins match
the ones used on Armada XP and Kirkwood.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There was a mistake in the definition of the functions for MPP48 on
Marvell Armada XP. The second function is dev(clkout), and not tclk.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: <stable@vger.kernel.org> # v3.7+
Fixes: 463e270f76 ("pinctrl: mvebu: add pinctrl driver for Armada XP")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The latest version of the Armada XP datasheet no longer documents the
VDD cpu_pd functions, which might indicate they are not working and/or
not supported. This commit ensures the pinctrl driver matches the
datasheet.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: <stable@vger.kernel.org> # v3.7+
Fixes: 463e270f76 ("pinctrl: mvebu: add pinctrl driver for Armada XP")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
After updating to a more recent version of the Armada XP datasheet, we
realized that some of the pins documented as having a NAND-related
functionality in fact did not have such functionality. This commit
updates the pinctrl driver accordingly.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: <stable@vger.kernel.org> # v3.7+
Fixes: 463e270f76 ("pinctrl: mvebu: add pinctrl driver for Armada XP")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
After updating to a more recent version of the Armada 375, we realized
that some of the pins documented as having a NAND-related
functionality in fact did not have such functionality. This commit
updates the pinctrl driver accordingly.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: <stable@vger.kernel.org> # v3.15+
Fixes: ce3ed59dcd ("pinctrl: mvebu: add pin-muxing driver for the Marvell Armada 375")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Due to a mistake, the CS0 and CS1 SPI0 functions were incorrectly
named "spi0-1" instead of just "spi0". This commit fixes that.
This DT binding change does not affect any of the in-tree users.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: <stable@vger.kernel.org> # v3.7+
Fixes: 5f597bb2be ("pinctrl: mvebu: add pinctrl driver for Armada 370")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
A new revision of the Marvell Armada 38x hardware datasheet unveiled
that the definition of some of the PCIe functions were not
correct. This commit fixes the pinctrl driver accordingly.
Some PCIe functions simply do not exist, some of the PCIe functions in
fact were corresponding to other functions, and some PCIe functions
have been added.
Note: the seemingly unrelated removal of spi(cs2) on MPP47 is related:
this function is in fact implemented on MPP43, instead of a PCIe
function.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: <stable@vger.kernel.org> # v3.15+
Fixes: ca6d9a084b ("pinctrl: mvebu: add pin-muxing driver for the Marvell Armada 380/385")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Added support to Zynq Ultrascale+ MPSoC on the existing zynq
gpio driver.
Signed-off-by: Anurag Kumar Vulisha <anuragku@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add a GPIO driver for the General I/O block on Axis ETRAX FS SoCs.
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add AverMedia AverTV/505 card to saa7134 driver. It is a card bearing
SAA7130HL chip and FQ1216ME/IH-3 tuner.
Working: Composite, TV and IR remote control.
Untested: S-Video.
[mchehab@osg.samsung.com: fix CodingStyle]
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Use a table for the Demux output. No new information added
here. They were all merged inside the table.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Use a table for the delivery systems. The table is organized
by the type (cable, satellite, terrestrial) and shows what
standards are not fully implemented.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Instead of using a program listing, use a table and make clearer
what each define means.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The table were documented at the legacy ioctl call. Move it
to the DVBv5 ioctl, and add a cross ref link on the legacy
section.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Putting it into a table allows to comment each possible
values, with makes more clear what field means.
Also, it allows to do cross-references with the frontend.h.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Those data were retrieved by looking at A/153: ATSC Mobile DTV
Standard and guessing what makes more sense to each field.
Cc: Michael Ira Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The ATSC M/H specific properties are not properly documented.
This became crearer when converting the existing data into
tables and adding cross references.
For now, just add placeholders, as a further investigation
about the meaning of each parameter is required.
Cc: Michael Ira Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
By cut-and-paste mistake, TRANSMISSION_MODE_AUTO were documented
twice, one at the wrong place.
Remove the wrong one.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
enum fe_bandwidth is documented at the frontend legacy xml
file.
Add xrefs for each entry there. This makes the hyperlinks at
frontend.h to go directly to the right documentation.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There are lots of enums that are defined at dvbproperty.
Add xrefs for each entry there. This makes the hyperlinks at
frontend.h to go directly to the right documentation.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
enum fe_sec_voltage is documented together with FE_SET_VOLTAGE.
Add xrefs for each entry there. This makes the hyperlinks at
frontend.h to go directly to the right documentation.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
enum fe_sec_tone_mode is documented together with FE_SET_TONE.
Add xrefs for each entry there. This makes the hyperlinks at
frontend.h to go directly to the right documentation.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
enum fe_status is documented together with FE_READ_STATUS.
Add xrefs for each entry there. This makes the hyperlinks at
frontend.h to go directly to the right documentation.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
enum fe_sec_mini_cmd is documented together with
FE_DISEQC_SEND_BURST.
Add xrefs for each entry there. This makes the hyperlinks at
frontend.h to go directly to the right documentation.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
enum fe_caps is documented at FE_GET_INFO ioctl. Add xrefs
for each entry there. This makes the hyperlinks at frontend.h
to go directly to the right documentation.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
In order to be sure that all enum definitions will be documented,
let's parse the enum values and add xref links to them.
Lots of missing references will be risen as we miss adding
id's to those symbols at the documentation. Next patches will
fix this.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Combine the ChipIdea USB binding into a single document to reduce
duplication and fragmentation. This marks use of the old PHY bindings as
deprecated. Future compatible bindings should use generic PHY binding.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Ivan T. Ivanov <iivanov@mm-sol.com>
Cc: Peter Chen <peter.chen@freescale.com>
Cc: Daniel Tang <dt.tangr@gmail.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Maxim MAX77621 device is high-efficiency, three-phase,
DC-DC step-down switching regulator delivers peak
output currents up to 16A. This device is extension of
MAX8973 and compatible with the register definition.
The MAX77621 has the SHUTDOWN pin which is EN pin on the
MAX8973. On MAX77621, the SHUTDOWN pin (active low) reset
device register to its POR/OTP value. The voltage output
is enabled when SHUTDONW pin is HIGH and EN bit on VOUT
register is HIGH.
For MAX8973, VOUT is enabled when EN bit or EN pin is high.
Add support of the MAX77621 device on max8973 regulator driver
with following changes:
- Make sure SHUTDOWN pin is set HIGH through GPIO calls if
GPIO from AP connected to SHUTDOWN pin provided.
- Enable/disable the rail through register access only.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch fix some spelling typo found in Documentations/sound/oss.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch was split out of Lubomir's original mailbox patch by Eric
Anholt, and the required properties documentation and examples have
been filled out more completely and updated for the driver being
changed to expose a single channel.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Craig McGeachie <slapdau@yahoo.com.au>
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
MPX has the _potential_ to cause some issues. Say part of your
init system tried to protect one of its components from buffer
overflows with MPX. If there were a false positive, it's
possible that MPX could keep a system from booting.
MPX could also potentially cause performance issues since it is
present in hot paths like the unmap path.
Allow it to be disabled at boot time.
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Dave Hansen <dave@sr71.net>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20150607183702.2E8B77AB@viggo.jf.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Freescale introduced QorIQ series SOCs, like ls1021 ls2085, with AHCI
sata support. It complies with the serial ATA 3.0 specification
and the AHCI 1.3 specification.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Yuantian Tang <Yuantian.Tang@freescale.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
A week late but I managed to complete it all and moved it into Git, for better
structure and easy pulling.
Changes relative to the last submission:
- Added higher level subsystem directories to collect features by
subsystem:
triton:~/tip> ls Documentation/features/
arch-support.txt core debug io lib list-arch.sh locking perf sched seccomp time vm
each subsystem directory contains the feature directories. For example locking
has:
triton:~/tip> ls Documentation/features/locking/
cmpxchg-local lockdep queued-rwlocks queued-spinlocks rwsem-optimized
It's all pretty straightforward to navigate. Advantages are better
visualization, plus git log is able to list changes per subsystem.
- Prettified the visualization some more.
- Improved/corrected the support matrices based on feedback to earlier submissions.
- Updated the support matrices to today's linux-next, so that by the time this
shows up in upstream in the next merge window it's really recent.
Most notably there's a new architecture in linux-next (h8300).
This structure should address all feedback that I got and should minimize the
maintenance overhead (chance of conflicts).
Updated struct file_operations documentation in vfs.txt to match
current implementation
Signed-off-by: Thomas de Beauchene <chauvo_t@epitech.eu>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Fix the device tree entries to modify the '_' to '-'.
Also changes the names of the internal delay properties
from -int- to -internal- as the -int- appeared as a keyword.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 976591810f (kbuild Update documentation of clean-files and clean-dirs)
changed the example for the clean-files variable, but left the explanation
unchanged. Edit the explanation to match the example.
Signed-off-by: Jeffrey Rogers <jeffreydavidrogers@gmail.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Various boot loaders for Exynos based boards use certain memory
addresses during booting for different purposes. Mostly this is one of
following :
1. as a CPU boot address,
2. for storing magic cookie related to low power mode (AFTR, sleep).
The document, based solely on kernel source code, tries to group the
information scattered over different files. This would help in the
future when adding support for new SoC or when extending features
related to low power modes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
This adds support for the LIS331DL sensor version. This is
a simple 8bit-only accelerometer.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The current versions of the trf7970a has an erratum where it returns
an extra byte in the response to 'Read Multiple Block' (RMB) commands.
This command is issued to Type 5 tags (i.e., ISO/IEC 15693 tags) by
the neard daemon.
To handle this, define a new Device Tree property,
't5t-rmb-extra-byte-quirk', which indicates that the associated
trf7970a device has this erratum. The trf7970a device driver
will then ensure that the response length to RMB commands is
reduced by one byte (for devices with the erratum).
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
About 10 days worth of small bug fixes, and the (hopefully) final
round fixes for from arm-soc land for the -rc cycle. Nothing special
to note, but here's a brief summary of fixes by SoC type:
- OMAP: small set of misc. DT fixes; boot fix for THUMB2 kernel
- mediatek: PMIC fixes; DT fix for model name
- exynos: wakeup interupt fixes for 3250
- mvebu: revert mbus patch which broke DMA masters
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=gSjy
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Kevin Hilman:
"About 10 days worth of small bug fixes, and the (hopefully) final
round fixes for from arm-soc land for the -rc cycle. Nothing special
to note, but here's a brief summary of fixes by SoC type:
- OMAP:
small set of misc DT fixes; boot fix for THUMB2 kernel
- mediatek:
PMIC fixes; DT fix for model name
- exynos:
wakeup interupt fixes for 3250
- mvebu:
revert mbus patch which broke DMA masters
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: dts: am335x-boneblack: disable RTC-only sleep to avoid hardware damage
ARM: dts: AM35xx: fix system control module clocks
arm64: dts: mt8173-evb: fix model name
ARM: exynos: Fix wake-up interrupts for Exynos3250
ARM: dts: Fix n900 dts file to work around 4.1 touchscreen regression on n900
ARM: dts: Fix dm816x to use right compatible flag for MUSB
ARM: OMAP3: Fix booting with thumb2 kernel
Revert "bus: mvebu-mbus: make sure SDRAM CS for DMA don't overlap the MBus bridge window"
bus: mvebu-mbus: do not set WIN_CTRL_SYNCBARRIER on non io-coherent platforms.
ARM: mvebu: armada-xp-linksys-mamba: Disable internal RTC
soc: mediatek: Add compile dependency to pmic-wrapper
soc: mediatek: PMIC wrap: Fix register state machine handling
soc: mediatek: PMIC wrap: Fix clock rate handling
The big thing this release has been Liam's addition of topology support
to the core. We've also seen quite a bit of driver work and the
continuation of Lars' refactoring for component support.
- Support for loading ASoC topology maps from firmware, intended to be
used to allow self-describing DSP firmware images to be built which
can map controls added by the DSP to userspace without the kernel
needing to know about individual DSP firmwares.
- Lots of refactoring to avoid direct access to snd_soc_codec where
it's not needed supporting future refactoring.
- Big refactoring and cleanup serieses for the Wolfson ADSP and TI
TAS2552 drivers.
- Support for TI TAS571x power amplifiers.
- Support for Qualcomm APQ8016 and ZTE ZX296702 SoCs.
- Support for x86 systems with RT5650 and Qualcomm Storm.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVddV1AAoJECTWi3JdVIfQQQsH/RG3lgOeot5jLWMsxJSKChEl
KI+aaMcOw6Dj2LDccN8i6vUp8q44cKSXIc7lGLOzJW4K+OydCCGAvE+sJGyRE1dd
yOHwcbvjJi4zFlt01RZchJ/Wa/S6zFucl5N9HxWsV4bEtfAA59IuhJLtospUlwsA
mf9mpvSdeUAeh3lM2+AqAbXhTo6dYfD5ky5nrtpAkZjG8gqUG0u8Tpauja0lLcHi
72/3EkzKR6KHaefyPw3LdN+/H/YK79uHCVcctZnQg5xUUymcO16ReoTxKwV9cnDb
lBJ6wO8RpUAO9evoG2Yj/l4p+czDCm5VkHMq0nPklHVRh7s/2PwKfox1aw4Pumg=
=wolq
-----END PGP SIGNATURE-----
Merge tag 'asoc-v4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: Updates for v4.2
The big thing this release has been Liam's addition of topology support
to the core. We've also seen quite a bit of driver work and the
continuation of Lars' refactoring for component support.
- Support for loading ASoC topology maps from firmware, intended to be
used to allow self-describing DSP firmware images to be built which
can map controls added by the DSP to userspace without the kernel
needing to know about individual DSP firmwares.
- Lots of refactoring to avoid direct access to snd_soc_codec where
it's not needed supporting future refactoring.
- Big refactoring and cleanup serieses for the Wolfson ADSP and TI
TAS2552 drivers.
- Support for TI TAS571x power amplifiers.
- Support for Qualcomm APQ8016 and ZTE ZX296702 SoCs.
- Support for x86 systems with RT5650 and Qualcomm Storm.
As reminded by Jonathan, several places where emphasys
role="tt" were used are actually trying to change the font to
monospaced.
We do that, on other places, by using the constant tag.
So, use it here too.
Reported-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This resolves a merge issue in musb_core.c and we want the fixes that
were in Linus's tree in this branch as well for testing.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We don't want to announce anything, but to add a note ;)
So:
notice -> note
notided -> noted
While here, fix another typo at media_api.tmpl:
with -> which
Reported-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add overview of tas2552's clock configuration and selection.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
According with the docs at docbook.org, no backward compatible
changes were done between 4.2 and 4.5 schemas. Some fixes were
added, together with new features. So, let's use the latest
4.x schema.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The DVB network API was not documented. There are just some
placeholders there.
Replace it by a proper documentation.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This fixes up a merge issue with the amba-pl011.c driver, and we want
the fixes in this branch as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
breakage on BeagleBones:
- BeagleBones don't support RTC-only mode, it can cause hardware
damage if system-power-controller is specified without
ti,pmic-shutdown-controller
- Fix a recent regression to am3517 SoCs caused by the recent clock
move that was not noticed until now despite automated boot
testing
- Fix a regression for n900 touchscreen triggered by recent
recent input changes
- Fix compatible property for dm816x USB to avoid errors with
USB Ethernet
- Fix oops for omap3 when built with CONFIG_THUMB2_KERNEL
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Saui
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.1/fixes-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Merge omap fixes for v4.1, urgent fix to avoid potential hardware damage From Tony Lindgren:
Omap fixes for the -rc cycle, including a fix for potential hardware
breakage on BeagleBones:
- BeagleBones don't support RTC-only mode, it can cause hardware
damage if system-power-controller is specified without
ti,pmic-shutdown-controller
- Fix a recent regression to am3517 SoCs caused by the recent clock
move that was not noticed until now despite automated boot
testing
- Fix a regression for n900 touchscreen triggered by recent
recent input changes
- Fix compatible property for dm816x USB to avoid errors with
USB Ethernet
- Fix oops for omap3 when built with CONFIG_THUMB2_KERNEL
* tag 'omap-for-v4.1/fixes-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am335x-boneblack: disable RTC-only sleep to avoid hardware damage
ARM: dts: AM35xx: fix system control module clocks
ARM: dts: Fix n900 dts file to work around 4.1 touchscreen regression on n900
ARM: dts: Fix dm816x to use right compatible flag for MUSB
ARM: OMAP3: Fix booting with thumb2 kernel
Rename the following system call entry points:
ia32_cstar_target -> entry_SYSCALL_compat
ia32_syscall -> entry_INT80_compat
The generic naming scheme for x86 system call entry points is:
entry_MNEMONIC_qualifier
where 'qualifier' is one of _32, _64 or _compat.
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
add support for new CSR atlas7 SoC. atlas7 exists V1 and V2 IP.
atlas7 DMAv1 is basically moved from marco, which has never been
delivered to customers and renamed in this patch.
atlas7 DMAv2 supports chain DMA by a chain table, this
patch also adds chain DMA support for atlas7.
atlas7 DMAv1 and DMAv2 co-exist in the same chip. there are some HW
configuration differences(register offset etc.) with old prima2 chips,
so we use compatible string to differentiate old prima2 and new atlas7,
then results in different set in HW for them.
Signed-off-by: Hao Liu <Hao.Liu@csr.com>
Signed-off-by: Yanchang Li <Yanchang.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Support configurable conversion mode through sysfs. So far, the
mode used was low-power, which is enabled by default now. Beside
that, the modes normal and high-speed are selectable as well.
Use the new device tree property which specifies the maximum ADC
conversion clock frequencies. Depending on the mode used, the
available resulting conversion frequency are calculated
dynamically.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Initialize and prepare for handling LMCEs. Add a boot-time
option to disable LMCEs.
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
[ Simplify stuff, align statements for better readability, reflow comments; kill
unused lmce_clear(); save us an MSR write if LMCE is already enabled. ]
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/1433436928-31903-16-git-send-email-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Now that reserve_ram_pages_type() accepts the WT type, add
set_memory_wt(), set_memory_array_wt() and set_pages_array_wt()
in order to be able to set memory to Write-Through page cache
mode.
Also, extend ioremap_change_attr() to accept the WT type.
Signed-off-by: Toshi Kani <toshi.kani@hp.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Elliott@hp.com
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Luis R. Rodriguez <mcgrof@suse.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: arnd@arndb.de
Cc: hch@lst.de
Cc: hmh@hmh.eng.br
Cc: jgross@suse.com
Cc: konrad.wilk@oracle.com
Cc: linux-mm <linux-mm@kvack.org>
Cc: linux-nvdimm@lists.01.org
Cc: stefan.bader@canonical.com
Cc: yigal@plexistor.com
Link: http://lkml.kernel.org/r/1433436928-31903-13-git-send-email-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Add ioremap_wt() for creating Write-Through mappings on x86. It
follows the same model as ioremap_wc() for multi-arch support.
Define ARCH_HAS_IOREMAP_WT in the x86 version of io.h to
indicate that ioremap_wt() is implemented on x86.
Also update the PAT documentation file to cover ioremap_wt().
Signed-off-by: Toshi Kani <toshi.kani@hp.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Elliott@hp.com
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Luis R. Rodriguez <mcgrof@suse.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: arnd@arndb.de
Cc: hch@lst.de
Cc: hmh@hmh.eng.br
Cc: jgross@suse.com
Cc: konrad.wilk@oracle.com
Cc: linux-mm <linux-mm@kvack.org>
Cc: linux-nvdimm@lists.01.org
Cc: stefan.bader@canonical.com
Cc: yigal@plexistor.com
Link: http://lkml.kernel.org/r/1433436928-31903-8-git-send-email-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This patch adds a new documentation file explaining the DSCR support on
powerpc platforms. This explains DSCR related data structure, code paths
and also available user interfaces. Any further functional changes to
the DSCR support in the kernel should definitely update the
documentation here.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Here are some USB and PHY driver fixes that resolve some reported
regressions. Also in here are some new device ids. All of the details
are in the shortlog and these patches have been in linux-next with no
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlVzhIcACgkQMUfUDdst+ykY9ACg0HeMGzJAfsWSLiSsBRpDxFAr
ixAAnjOYj4Gv+XtAD4ZiOuMpaQaADntQ
=4uxU
-----END PGP SIGNATURE-----
Merge tag 'usb-4.1-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB and PHY driver fixes from Greg KH:
"Here are some USB and PHY driver fixes that resolve some reported
regressions. Also in here are some new device ids.
All of the details are in the shortlog and these patches have been in
linux-next with no problems"
* tag 'usb-4.1-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (22 commits)
USB: cp210x: add ID for HubZ dual ZigBee and Z-Wave dongle
usb: renesas_usbhs: Don't disable the pipe if Control write status stage
usb: renesas_usbhs: Fix fifo unclear in usbhsf_prepare_pop
usb: gadget: f_fs: fix check in read operation
usb: musb: fix order of conditions for assigning end point operations
usb: gadget: f_uac1: check return code from config_ep_by_speed
usb: gadget: ffs: fix: Always call ffs_closed() in ffs_data_clear()
usb: gadget: g_ffs: Fix counting of missing_functions
usb: s3c2410_udc: correct reversed pullup logic
usb: dwc3: gadget: Fix incorrect DEPCMD and DGCMD status macros
usb: phy: tahvo: Pass the IRQF_ONESHOT flag
usb: phy: ab8500-usb: Pass the IRQF_ONESHOT flag
usb: renesas_usbhs: Revise the binding document about the dma-names
usb: host: xhci: add mutex for non-thread-safe data
usb: make module xhci_hcd removable
USB: serial: ftdi_sio: Add support for a Motion Tracker Development Board
usb: gadget: f_midi: fix segfault when reading empty id
phy: phy-rcar-gen2: Fix USBHS_UGSTS_LOCK value
phy: omap-usb2: invoke pm_runtime_disable on error path
phy: fix Kconfig dependencies
...
Make sure that the documentation clearly states who is zeroing reserved
fields: drivers and/or applications.
This patch syncs the documentation with the checks that v4l2-compliance
and valgrind do.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This has been on my TODO list for some time now: the control that enables the video
loopback was part of the controls of the video output device instead of the video
capture device. In practice this was quite annoying since you expect it at the capture
side since that's where you want to make the decision whether to use the TPG or looped
video.
This patch moves the control from the output to the capture side.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
* clk-meson8b:
clk: meson8b: Add support for Meson8b clocks
clk: meson: Document bindings for Meson8b clock controller
clk: meson: Add support for Meson clock controller
APM X-Gene v1 SoC supports its own implementation of MSI, which is not
compliant to GIC V2M specification for MSI Termination.
There is a single MSI block in X-Gene v1 SOC which serves all 5 PCIe ports.
This MSI block supports 2048 MSI termination ports coalesced into 16
physical HW IRQ lines and shared across all 5 PCIe ports.
As there are only 16 HW IRQs to serve 2048 MSI vectors, to support
set_affinity correctly for each MSI vectors, the 16 HW IRQs are statically
allocated to 8 X-Gene v1 cores (2 HW IRQs for each cores). To steer MSI
interrupt to target CPU, MSI vector is moved around these HW IRQs lines.
With this approach, the total MSI vectors this driver supports is reduced
to 256.
[bhelgaas: squash doc, driver, maintainer update]
Signed-off-by: Duc Dang <dhdang@apm.com>
Signed-off-by: Tanmay Inamdar <tinamdar@apm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Using a fixed (by DTS) parent for clocks when turning on the power
domain may introduce issues in other drivers. For example when such
driver changes the parent during runtime and expects that he is the
only place of such change.
Do not rely on DTS providing the fixed parent for such clocks. Instead
before switching domain off, grab a current parent of a clock with
clk_get_parent().
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Follow up to commit e194bbdf36.
Suggested-by: Bandan Das <bsd@redhat.com>
Suggested-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This is now very simple to do. The only interesting part is a simple
trick to find the right memslot in gfn_to_rmap, retrieving the address
space from the spte role word. The same trick is used in the auditing
code.
The comment on top of union kvm_mmu_page_role has been stale forever,
so remove it. Speaking of stale code, remove pad_for_nice_hex_output
too: it was splitting the "access" bitfield across two bytes and thus
had effectively turned into pad_for_ugly_hex_output.
Reviewed-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Only two ioctls have to be modified; the address space id is
placed in the higher 16 bits of their slot id argument.
As of this patch, no architecture defines more than one
address space; x86 will be the first.
Reviewed-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Document the new Transfer Function control (and fix the documentation for
the other colorspace controls which were not quite correct).
Mention the support for 4:2:0 and more multiplanar formats.
Update the TODO list at the end.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Document the new field and defines to set the transfer function needed
to correctly decode the colors of an image.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch adds documentation for the devicetree bindings used by the
DT files of Hisilicon hi6220 SoC mobile platform.
Signed-off-by: Bintian Wang <bintian.wang@huawei.com>
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
This patch adds two boolean properties to FMan Port.
FMan has 3 types of ports:
- 1G ports
By default, all ports support 1G rate
- 10G Ports
Port which use 10G hardware, and configured as 10G
- 10G Best effort ports
Ports which use 1G hardware, configured as 10G, in this case,
the rate is not guaranteed.
The new properties help to distinguish the different type of ports.
Signed-off-by: Igal Liberman <igal.liberman@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
The check_acl inode operation and the IPERM_FLAG_RCU flag are long gone; update
the documentation.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Documentation/networking/timestamping/txtimestamp.c: In function ‘__print_timestamp’:
Documentation/networking/timestamping/txtimestamp.c:99:3: warning: format ‘%ld’ expects argument of type ‘long int’, but argument 3 has type ‘int64_t’ [-Wformat=]
fprintf(stderr, " (%+ld us)", cur_ms - prev_ms);
int64_t differs per platform, so a type specifier that differs along
with it is required.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
The current documentation is incomplete wrt the intel_pstate legacy
internal governors. The confusion comes from the general cpufreq
governors which also use the names performance and powersave. This patch
better differentiates between the two sets of governors and gives an
explanation of how the internal P-state governors behave differently from
one another.
Also fix two minor typos.
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: "Rafael J. Wysocki" <rafael.j.wysocki@intel.com>
Cc: Kristen Carlson Accardi <kristen@linux.intel.com>
Cc: Dirk Brandewie <dirk.j.brandewie@intel.com>
Cc: x86@kernel.org
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Current documentation over use case for EXPORT_SYMBOL_GPL()
only acknowledges functions which are "an internal implementation
issue, and not really an interface". In practice these days
though we have some maintainers taking on preferences to require
all new functionality go in with EXPORT_SYMBOL_GPL().
A maintainer asking developers to use EXPORT_SYMBOL_GPL()
for new functionality tends to be a well accepted and understood
position that maintainers can take and typically requires the
maintainers educating contributing developers on their own
positions and requirements.
Developers who submit code to maintainers not familiar with
these preferences as optional for new functionality need explicit
guidence though as existing documentation does not acknowledge
this as a valid possibility. Without this being documented some
maintainers are reluctant to accept new functionality with
EXPORT_SYMBOL_GPL().
This extends the use case documentation for EXPORT_SYMBOL_GPL()
to acknowledge acceptance for new functionality.
Signed-off-by: Luis R. Rodriguez <mcgrof@suse.com>
[jc: wording tweaked with permission]
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
This patch includes changes to the external API for SMM support.
Userspace can predicate the availability of the new fields and
ioctls on a new capability, KVM_CAP_X86_SMM, which is added at the end
of the patch series.
Reviewed-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch adds the devicetree documentation for the ZTE
zx296702 I2S audio controller.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds the devicetree documentation for the ZTE
zx296702 SPDIF audio controller.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Patch "gpiolib: rename gpiod_set_array to gpiod_set_array_value" omitted
to also change the function names in the documentation. Let's fix that.
Signed-off-by: Rojhalat Ibrahim <imr@rtschenk.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
A33 PIO has 7 ports which starts from PB and has two interrupt ports.
Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch fix some spelling typo found in crypto-API.tmpl
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Stephan Mueller <smueller@chronox.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Clarify in documentation and code that IPV4 FIB add operation is used for
both adding a new FIB entry to the device and for modifying an existing FIB
entry on the device.
Also, remove left-over references to ipv4_fib ops and replace with details
on SWITCHDEV_PORT_IPV4_FIB object.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the TI dp83867 Gigabit ethernet phy
device.
The DP83867 is a robust, low power, fully featured
Physical Layer transceiver with integrated PMD
sublayers to support 10BASE-T, 100BASE-TX and
1000BASE-T Ethernet protocols.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Please pull the contents of "Use DRM component API in tilcdc to
connect to tda998x" patch series.
* 'linux-4.1.0-rc5-tilcdc-refactor' of https://github.com/jsarha/linux:
drm/tilcdc: Force building of DRM_TILCDC_SLAVE_COMPAT
drm/tilcdc: Add DRM_TILCDC_SLAVE_COMPAT for ti,tilcdc,slave binding support
drm/tilcdc: use pm_runtime_irq_safe()
drm/tilcdc: Add support for external tda998x encoder
drm/tilcdc: Remove tilcdc slave support for tda998x driver
drm/tilcdc: Fix module unloading
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVa7zvAAoJEHm+PkMAQRiGtfMIAILs3sxFtrC1hApgcfRLF/7z
K34bwTRqErzqUO/orTwakEr9kSIpIL0zIPSryTCOTPZLfMGkQjhHXO3KR/DSbbTV
MZ8y/BM/yelFA/Np+1LjbiYjTNRnTRvCoaQihkIH8Rn02g7ob9HyL4gIGKpuGFcZ
04GacL2cgChqsRSACdNef948jCoJXKgcuDpe39DXphDWZnBKNZ3HFuJ6bryGJf9A
1/eCI4is85BNwKPemQUYR0xx83UIzDfrghatZP2mOCDDSA2MNg8HNxLTd12LGoQD
tfgX4B7aftzW9Y7GSEDfZ0IKm2NRzgPmCVj6PjVR/iI0lIK4Aq0Z/lDJxxEq3XQ=
=AJM5
-----END PGP SIGNATURE-----
Merge tag 'v4.1-rc6' into drm-next
Linux 4.1-rc6
backmerge 4.1-rc6 as some of the later pull reqs are based on newer bases
and I'd prefer to do the fixup myself.
One more round of drm-misc, again mostly atomic. Big thing is the
userspace blob code from Daniel Stone, with support for the mode_id blob
now added to the atomic ioctl. Finally we can do atomic modesets!
Note that the atomic ioctl is still behind the module knob since the
weston patches aren't quite ready yet imo - they lack TEST_ONLY support,
which is a fairly crucial bit of the atomic api. But besides that I think
it's all good to go. That's also why we didn't bother to hide the new blob
ioctls behind the knob, that part won't need to change. And if weston
patches get in shape in time we could throw the "atomic by default patch"
on top for 4.2.
* tag 'topic/drm-misc-2015-05-27' of git://anongit.freedesktop.org/drm-intel:
drm: Fix off-by-one in vblank hardware counter wraparound handling
drm/atomic: fix out of bounds read in for_each_*_in_state helpers
drm/atomic: Add MODE_ID property
drm/atomic: Add current-mode blob to CRTC state
drm: Add drm_atomic_set_mode_for_crtc
drm: check for garbage in unused addfb2 fields
drm: Retain reference to blob properties in lookup
drm/mode: Add user blob-creation ioctl
drm: Return error value from blob creation
drm: Allow creating blob properties without copy
drm/mode: Unstatic kernel-userspace mode conversion
drm/mode: Validate modes inside drm_crtc_convert_umode
drm/crtc_helper: Replace open-coded CRTC state helpers
drm: kerneldoc fixes for blob properties
drm/DocBook: Add more drm_bridge documentation
drm: bridge: Allow daisy chaining of bridges
drm/atomic: add all affected planes in drm_atomic_helper_check_modeset
drm/atomic: add drm_atomic_add_affected_planes
drm/atomic: add commit_planes_on_crtc helper
This adds documentation of device tree bindings for the
thermal sensor controller of hi6220 SoC.
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: kongxinwei <kong.kongxinwei@hisilicon.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
This driver supports the TI CDCE925 programmable clock synthesizer.
The chip contains two PLLs with spread-spectrum clocking support and
five output dividers. The driver only supports the following setup,
and uses a fixed setting for the output muxes:
Y1 is derived from the input clock
Y2 and Y3 derive from PLL1
Y4 and Y5 derive from PLL2
Given a target output frequency, the driver will set the PLL and
divider to best approximate the desired output.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Even if not documented in the datasheet, the Armada 370 SoC can actually
gate the CESA (crypto engine) clock.
Add an entry in the gating_desc table to be able to reference the CESA
gateclk in the crypto node.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
The previous patches added arch support matrices for more than 40 generic kernel features
that need per architecture support.
The structure of the feature descriptions is the following:
Each feature has its own directory under Documentation/features/subsystem_name/feature_name/,
and the arch-support.txt file shows its current arch porting status.
For example, lockdep support is shown the following way:
triton:~/tip> cat Documentation/features/locking/lockdep/arch-support.txt
#
# Feature name: lockdep
# Kconfig: LOCKDEP_SUPPORT
# description: arch supports the runtime locking correctness debug facility
#
-----------------------
| arch |status|
-----------------------
| alpha: | TODO |
| arc: | ok |
| arm: | ok |
| arm64: | ok |
| avr32: | ok |
| blackfin: | ok |
| c6x: | TODO |
| cris: | TODO |
| frv: | TODO |
| h8300: | TODO |
| hexagon: | ok |
| ia64: | TODO |
| m32r: | TODO |
| m68k: | TODO |
| metag: | ok |
| microblaze: | ok |
| mips: | ok |
| mn10300: | TODO |
| nios2: | TODO |
| openrisc: | TODO |
| parisc: | TODO |
| powerpc: | ok |
| s390: | ok |
| score: | ok |
| sh: | ok |
| sparc: | ok |
| tile: | ok |
| um: | ok |
| unicore32: | ok |
| x86: | ok |
| xtensa: | ok |
-----------------------
For generic kernel features that need architecture support, the
arch-support.txt file in each feature directory shows the arch
support matrix, for all upstream Linux architectures.
The meaning of entries in the tables is:
| ok | # feature supported by the architecture
|TODO| # feature not yet supported by the architecture
| .. | # feature cannot be supported by the hardware
This directory structure can be used in the future to add other
files - such as porting guides, testing description, etc.
The Documentation/features/ hierarchy may also include generic
kernel features that works on every architecture, in that case
the arch-support.txt file will list every architecture as
supported.
To list an architecture's unsupported features, just do something
like:
triton:~/tip> git grep -lE 'x86.*TODO' Documentation/features/*/*/arch-support.txt
Documentation/features/lib/strncasecmp/arch-support.txt
Documentation/features/time/arch-tick-broadcast/arch-support.txt
which will print the list of not yet supported features.
The Documentation/features/list-arch.sh script will print the current
support matrix of one architecture:
triton:~/tip> Documentation/features/list-arch.sh
#
# Kernel feature support matrix of the 'x86' architecture:
#
core/ BPF-JIT : ok | HAVE_BPF_JIT # arch supports BPF JIT optimizations
core/ generic-idle-thread : ok | GENERIC_SMP_IDLE_THREAD # arch makes use of the generic SMP idle thread facility
core/ jump-labels : ok | HAVE_ARCH_JUMP_LABEL # arch supports live patched, high efficiency branches
core/ tracehook : ok | HAVE_ARCH_TRACEHOOK # arch supports tracehook (ptrace) register handling APIs
debug/ gcov-profile-all : ok | ARCH_HAS_GCOV_PROFILE_ALL # arch supports whole-kernel GCOV code coverage profiling
debug/ KASAN : ok | HAVE_ARCH_KASAN # arch supports the KASAN runtime memory checker
debug/ kgdb : ok | HAVE_ARCH_KGDB # arch supports the kGDB kernel debugger
debug/ kprobes : ok | HAVE_KPROBES # arch supports live patched kernel probe
debug/ kprobes-on-ftrace : ok | HAVE_KPROBES_ON_FTRACE # arch supports combined kprobes and ftrace live patching
debug/ kretprobes : ok | HAVE_KRETPROBES # arch supports kernel function-return probes
debug/ optprobes : ok | HAVE_OPTPROBES # arch supports live patched optprobes
debug/ stackprotector : ok | HAVE_CC_STACKPROTECTOR # arch supports compiler driven stack overflow protection
debug/ uprobes : ok | ARCH_SUPPORTS_UPROBES # arch supports live patched user probes
debug/ user-ret-profiler : ok | HAVE_USER_RETURN_NOTIFIER # arch supports user-space return from system call profiler
io/ dma-api-debug : ok | HAVE_DMA_API_DEBUG # arch supports DMA debug facilities
io/ dma-contiguous : ok | HAVE_DMA_CONTIGUOUS # arch supports the DMA CMA (continuous memory allocator)
io/ dma_map_attrs : ok | HAVE_DMA_ATTRS # arch provides dma_*map*_attrs() APIs
io/ sg-chain : ok | ARCH_HAS_SG_CHAIN # arch supports chained scatter-gather lists
lib/ strncasecmp : TODO | __HAVE_ARCH_STRNCASECMP # arch provides an optimized strncasecmp() function
locking/ cmpxchg-local : ok | HAVE_CMPXCHG_LOCAL # arch supports the this_cpu_cmpxchg() API
locking/ lockdep : ok | LOCKDEP_SUPPORT # arch supports the runtime locking correctness debug facility
locking/ queued-rwlocks : ok | ARCH_USE_QUEUED_RWLOCKS # arch supports queued rwlocks
locking/ queued-spinlocks : ok | ARCH_USE_QUEUED_SPINLOCKS # arch supports queued spinlocks
locking/ rwsem-optimized : ok | Optimized asm/rwsem.h # arch provides optimized rwsem APIs
perf/ kprobes-event : ok | HAVE_REGS_AND_STACK_ACCESS_API # arch supports kprobes with perf events
perf/ perf-regs : ok | HAVE_PERF_REGS # arch supports perf events register access
perf/ perf-stackdump : ok | HAVE_PERF_USER_STACK_DUMP # arch supports perf events stack dumps
sched/ numa-balancing : ok | ARCH_SUPPORTS_NUMA_BALANCING # arch supports NUMA balancing
seccomp/ seccomp-filter : ok | HAVE_ARCH_SECCOMP_FILTER # arch supports seccomp filters
time/ arch-tick-broadcast : TODO | ARCH_HAS_TICK_BROADCAST # arch provides tick_broadcast()
time/ clockevents : ok | GENERIC_CLOCKEVENTS # arch support generic clock events
time/ context-tracking : ok | HAVE_CONTEXT_TRACKING # arch supports context tracking for NO_HZ_FULL
time/ irq-time-acct : ok | HAVE_IRQ_TIME_ACCOUNTING # arch supports precise IRQ time accounting
time/ modern-timekeeping : ok | !ARCH_USES_GETTIMEOFFSET # arch does not use arch_gettimeoffset() anymore
time/ virt-cpuacct : ok | HAVE_VIRT_CPU_ACCOUNTING # arch supports precise virtual CPU time accounting
vm/ ELF-ASLR : ok | ARCH_HAS_ELF_RANDOMIZE # arch randomizes the stack, heap and binary images of ELF binaries
vm/ huge-vmap : ok | HAVE_ARCH_HUGE_VMAP # arch supports the ioremap_pud_enabled() and ioremap_pmd_enabled() VM APIs
vm/ ioremap_prot : ok | HAVE_IOREMAP_PROT # arch has ioremap_prot()
vm/ numa-memblock : ok | HAVE_MEMBLOCK_NODE_MAP # arch supports NUMA aware memblocks
vm/ PG_uncached : ok | ARCH_USES_PG_UNCACHED # arch supports the PG_uncached page flag
vm/ pmdp_splitting_flush : ok | __HAVE_ARCH_PMDP_SPLITTING_FLUSH # arch supports the pmdp_splitting_flush() VM API
vm/ pte_special : ok | __HAVE_ARCH_PTE_SPECIAL # arch supports the pte_special()/pte_mkspecial() VM APIs
vm/ THP : ok | HAVE_ARCH_TRANSPARENT_HUGEPAGE # arch supports transparent hugepages
Cc: <linux-api@vger.kernel.org>
Cc: <linux-arch@vger.kernel.org>
Cc: <linux-kernel@vger.kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Josh Triplett <josh@joshtriplett.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This part just add necessary change to boot imx7d.
Update clock, pinctrl and gpt for imx7d
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
*) new Broadcom SATA3 PHY driver for Broadcom STB SoCs
*) new phy API to get PHY by index which is used in EHCI and
OHCI controller drivers
*) support specifying supply at port level used for multi-port PHYs
*) sparse warning fixes in miphy PHYs
*) fix pm_runtime issues in twl4030 driver
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJVbbvfAAoJEA5ceFyATYLZdAIP/2mFENq9DIRDqU7LV4aQRDlC
TlL+DLGwElAGKkq7bL3UaWy+10kooTmVaYVB1MACAPXZgKguTkjsSdWXDSxFHDyG
tq32CqkeMx1uhsZBMhdxsIsTnAPfEo1s2lO7O/HaJTq38aqKixC5+A3IYXttSvET
jF4XCx7IGNK7YIMylTzAW1FN9rHvsp4RRKIkPjS8EAiAbQIcu7rxKdSbfwJ69Zxt
EUep3u7jvlQK6SmOig3nkoQFf70G6d7p0VsBPrU6l6Dg9Ciu/5ZvzCkg5ukGotOl
1GIpowjW3abIaX6yGOD95phU8+JPZbncG/vrQ5Hf/FDZtvCgs6tYqY+Zqmxf7SlK
4Jj43+sjvDt05Ty9K1sP2FnQqBq9XKEmX5K1pYCrHDbDiH0L9gKeX9/46dJhDrMS
F3rfrcgBxqBqT96BsqPHmuN0uUvXaF7pGKyFWoGodblBsYee6z4XAl8Up62Lqq3U
QglegTz9ICKDU1j8xmjLHN9l21BfXANdirFTyjtV3XIGR6mcmzd3R3qk7x2ulaQ8
lA4gfUhm9X8f55FTqLIw+7Ld+rgEW9NYHSX4fFvtzB/T5SPdOrslgjby4i0a81Pv
IfQcLaQZ75QIj+22sy27cXrQsmUCe6sNXrms190uknh3hEHDeNOtPupYIMJcXiO+
n2YJ6QCOnly3tSMFNWfM
=vPk6
-----END PGP SIGNATURE-----
Merge tag 'phy-for-v4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-next
Kishon writes:
phy: for 4.2 merge window
*) new Broadcom SATA3 PHY driver for Broadcom STB SoCs
*) new phy API to get PHY by index which is used in EHCI and
OHCI controller drivers
*) support specifying supply at port level used for multi-port PHYs
*) sparse warning fixes in miphy PHYs
*) fix pm_runtime issues in twl4030 driver
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This patchset include the huge update of extcon core and add the new one extcon
driver and fix minor isseu of extcon drivers.
Detailed description for patchset:
1. Update the extcon core.
- Modify the extcon device name on sysfs from device name name to 'extcon[X]'
as following because if same extcon device are included in H/W development board,
the one of the two device driver might be failed on the probe().
: /sys/class/extcon/[device name] -> /sys/class/extcon/extcon[X]
- Use the unique id for external connectors instead of legacy string name.
Previously, extcon used the string name to identify the type of external
connectors. This way have the many potential issues. So, extcon core define the
unique id for each external connectors as following:
enum extcon {
EXTCON_NONE = 0x0,
/* USB external connector */
EXTCON_USB = 0x1,
EXTCON_USB_HOST = 0x2,
/* Charger external connector */
EXTCON_TA = 0x10,
EXTCON_FAST_CHARGER = 0x11,
EXTCON_SLOW_CHARGER = 0x12,
EXTCON_CHARGE_DOWNSTREAM = 0x13,
/* Audio and video external connector */
EXTCON_LINE_IN = 0x20,
EXTCON_LINE_OUT = 0x21,
EXTCON_MICROPHONE = 0x22,
EXTCON_HEADPHONE = 0x23,
...
};
- Update tye prototype of extcon_register_notifier() by using the unique id
(enum extcon) of external connectors.
- Add extcon_get_edev_name() API to get the name of extcon device on extcon
client driver because the name is included in 'struct extcon_dev' and 'struct
extcon_dev' should be handled in only drivers/extcon directory. So. if extcon
client need the name of extcon device, they could use this function.
- Unify the jig/dock and MHL-TA cable name on extcon driver.
: JIG-{USB-ON|USB-OFF|UART-ON|UART-OFF} -> JIG
: Dock-{Smart|Desk|Audio|Card} -> DOCK
: MHL-TA -> TA
- Use the capital letter for the name of all external connectors.
- Remove the optional print_name() function pointer from struct extcon_dev to
maintain the consistent name of extcon device.
2. Add the new extcon-axp288.c extcon driver.
- The extcon-axp288.c driver support for AXP288 PMIC which has the BC1.2
charger detection capability. So this extcon driver can detect the
EXTCON_SLOW_CHARGER, EXTCON_CHARGE_DOWNSTREAM and EXTCON_FAST_CHARGER.
3. Update the extcon-arizona.c driver.
- Add support for selective detection mode when headphone detection.
- Apply HP clamps for WM8280
4. Clean-up the extcon core and drivers.
- Add manufactor information of each extcon device.
- Fix checkpatch warning and minor coding style on extcon.c.c
- Fix build break if GPIOLIB is not enabled on extcon-usb-gpiio.c.
- Set the direction of gpio when calling devm_gpiod_get() on extcon-usb-gpio.c
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=Pc8L
-----END PGP SIGNATURE-----
Merge tag 'extcon-next-for-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/chanwoo/extcon into char-misc-next
Chanwoo writes:
Update extcon for v4.2
This patchset include the huge update of extcon core and add the new one extcon
driver and fix minor isseu of extcon drivers.
Detailed description for patchset:
1. Update the extcon core.
- Modify the extcon device name on sysfs from device name name to 'extcon[X]'
as following because if same extcon device are included in H/W development board,
the one of the two device driver might be failed on the probe().
: /sys/class/extcon/[device name] -> /sys/class/extcon/extcon[X]
- Use the unique id for external connectors instead of legacy string name.
Previously, extcon used the string name to identify the type of external
connectors. This way have the many potential issues. So, extcon core define the
unique id for each external connectors as following:
enum extcon {
EXTCON_NONE = 0x0,
/* USB external connector */
EXTCON_USB = 0x1,
EXTCON_USB_HOST = 0x2,
/* Charger external connector */
EXTCON_TA = 0x10,
EXTCON_FAST_CHARGER = 0x11,
EXTCON_SLOW_CHARGER = 0x12,
EXTCON_CHARGE_DOWNSTREAM = 0x13,
/* Audio and video external connector */
EXTCON_LINE_IN = 0x20,
EXTCON_LINE_OUT = 0x21,
EXTCON_MICROPHONE = 0x22,
EXTCON_HEADPHONE = 0x23,
...
};
- Update tye prototype of extcon_register_notifier() by using the unique id
(enum extcon) of external connectors.
- Add extcon_get_edev_name() API to get the name of extcon device on extcon
client driver because the name is included in 'struct extcon_dev' and 'struct
extcon_dev' should be handled in only drivers/extcon directory. So. if extcon
client need the name of extcon device, they could use this function.
- Unify the jig/dock and MHL-TA cable name on extcon driver.
: JIG-{USB-ON|USB-OFF|UART-ON|UART-OFF} -> JIG
: Dock-{Smart|Desk|Audio|Card} -> DOCK
: MHL-TA -> TA
- Use the capital letter for the name of all external connectors.
- Remove the optional print_name() function pointer from struct extcon_dev to
maintain the consistent name of extcon device.
2. Add the new extcon-axp288.c extcon driver.
- The extcon-axp288.c driver support for AXP288 PMIC which has the BC1.2
charger detection capability. So this extcon driver can detect the
EXTCON_SLOW_CHARGER, EXTCON_CHARGE_DOWNSTREAM and EXTCON_FAST_CHARGER.
3. Update the extcon-arizona.c driver.
- Add support for selective detection mode when headphone detection.
- Apply HP clamps for WM8280
4. Clean-up the extcon core and drivers.
- Add manufactor information of each extcon device.
- Fix checkpatch warning and minor coding style on extcon.c.c
- Fix build break if GPIOLIB is not enabled on extcon-usb-gpiio.c.
- Set the direction of gpio when calling devm_gpiod_get() on extcon-usb-gpio.c
Now that libcxl is public, let's document it.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Export the "AFU Error Buffer" via sysfs attribute (afu_err_buf). AFU
error buffer is used by the AFU to report application specific
errors. The contents of this buffer are AFU specific and are intended to
be interpreted by the application interacting with the afu.
Suggested-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Vaibhav Jain <vaibhav@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The patch updates the DocBook to cover the new AEAD interface
implementation.
Signed-off-by: Stephan Mueller <smueller@chronox.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
It turns out that existing U-Boots will dereference NULL pointers
if the device tree does not have cell-index in the portal nodes.
No patch has yet been merged adding device tree nodes for this binding
(except a dtsi that has not yet been referenced), nor has any driver
yet been merged making use of the binding, so it's not too late to
change the binding in order to keep compatibility with existing
U-Boots.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Madalin-Cristian Bucur <madalin.bucur@freescale.com>
Add Hardkernel Co., Ltd. to the list of device tree vendor prefixes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Smack onlycap allows limiting of CAP_MAC_ADMIN and CAP_MAC_OVERRIDE to
processes running with the configured label. But having single privileged
label is not enough in some real use cases. On a complex system like Tizen,
there maybe few programs that need to configure Smack policy in run-time
and running them all with a single label is not always practical.
This patch extends onlycap feature for multiple labels. They are configured
in the same smackfs "onlycap" interface, separated by spaces.
Signed-off-by: Rafal Krypa <r.krypa@samsung.com>
Currently, the FDT blob needs to be in the same 512 MB region as
the kernel, so that it can be mapped into the kernel virtual memory
space very early on using a minimal set of statically allocated
translation tables.
Now that we have early fixmap support, we can relax this restriction,
by moving the permanent FDT mapping to the fixmap region instead.
This way, the FDT blob may be anywhere in memory.
This also moves the vetting of the FDT to mmu.c, since the early
init code in head.S does not handle mapping of the FDT anymore.
At the same time, fix up some comments in head.S that have gone stale.
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This patch implements tape statistics in the st module via
sysfs. Current no statistics are available for tape I/O and there
is no easy way to reuse the block layer statistics for tape
as tape is a character device and does not have perform I/O in
sector sized chunks (the size of the data written to tape
can change). For tapes we also need extra stats related to
things like tape movement (via other I/O).
There have been multiple end users requesting statistics
including AT&T (and some HP customers who have not given
permission to be named). It is impossible for them
to investigate any issues related to tape performance
in a non-invasive way.
[jejb: eliminate PRId64]
Signed-off-by: Shane Seymour <shane.seymour@hp.com>
Tested-by: Shane Seymour <shane.seymour@hp.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Only include SCSI initiator header files in target code that needs
these header files, namely the SCSI pass-through code and the tcm_loop
driver. Change SCSI_SENSE_BUFFERSIZE into TRANSPORT_SENSE_BUFFER in
target code because the former is intended for initiator code and the
latter for target code. With this patch the only initiator include
directives in target code that remain are as follows:
$ git grep -nHE 'include .scsi/(scsi.h|scsi_host.h|scsi_device.h|scsi_cmnd.h)' drivers/target drivers/infiniband/ulp/{isert,srpt} drivers/usb/gadget/legacy/tcm_*.[ch] drivers/{vhost,xen} include/{target,trace/events/target.h}
drivers/target/loopback/tcm_loop.c:29:#include <scsi/scsi.h>
drivers/target/loopback/tcm_loop.c:31:#include <scsi/scsi_host.h>
drivers/target/loopback/tcm_loop.c:32:#include <scsi/scsi_device.h>
drivers/target/loopback/tcm_loop.c:33:#include <scsi/scsi_cmnd.h>
drivers/target/target_core_pscsi.c:39:#include <scsi/scsi_device.h>
drivers/target/target_core_pscsi.c:40:#include <scsi/scsi_host.h>
drivers/xen/xen-scsiback.c:52:#include <scsi/scsi_host.h> /* SG_ALL */
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
When modifying PG_Dirty on cached file pages, update the new
MEM_CGROUP_STAT_DIRTY counter. This is done in the same places where
global NR_FILE_DIRTY is managed. The new memcg stat is visible in the
per memcg memory.stat cgroupfs file. The most recent past attempt at
this was http://thread.gmane.org/gmane.linux.kernel.cgroups/8632
The new accounting supports future efforts to add per cgroup dirty
page throttling and writeback. It also helps an administrator break
down a container's memory usage and provides evidence to understand
memcg oom kills (the new dirty count is included in memcg oom kill
messages).
The ability to move page accounting between memcg
(memory.move_charge_at_immigrate) makes this accounting more
complicated than the global counter. The existing
mem_cgroup_{begin,end}_page_stat() lock is used to serialize move
accounting with stat updates.
Typical update operation:
memcg = mem_cgroup_begin_page_stat(page)
if (TestSetPageDirty()) {
[...]
mem_cgroup_update_page_stat(memcg)
}
mem_cgroup_end_page_stat(memcg)
Summary of mem_cgroup_end_page_stat() overhead:
- Without CONFIG_MEMCG it's a no-op
- With CONFIG_MEMCG and no inter memcg task movement, it's just
rcu_read_lock()
- With CONFIG_MEMCG and inter memcg task movement, it's
rcu_read_lock() + spin_lock_irqsave()
A memcg parameter is added to several routines because their callers
now grab mem_cgroup_begin_page_stat() which returns the memcg later
needed by for mem_cgroup_update_page_stat().
Because mem_cgroup_begin_page_stat() may disable interrupts, some
adjustments are needed:
- move __mark_inode_dirty() from __set_page_dirty() to its caller.
__mark_inode_dirty() locking does not want interrupts disabled.
- use spin_lock_irqsave(tree_lock) rather than spin_lock_irq() in
__delete_from_page_cache(), replace_page_cache_page(),
invalidate_complete_page2(), and __remove_mapping().
text data bss dec hex filename
8925147 1774832 1785856 12485835 be84cb vmlinux-!CONFIG_MEMCG-before
8925339 1774832 1785856 12486027 be858b vmlinux-!CONFIG_MEMCG-after
+192 text bytes
8965977 1784992 1785856 12536825 bf4bf9 vmlinux-CONFIG_MEMCG-before
8966750 1784992 1785856 12537598 bf4efe vmlinux-CONFIG_MEMCG-after
+773 text bytes
Performance tests run on v4.0-rc1-36-g4f671fe2f952. Lower is better for
all metrics, they're all wall clock or cycle counts. The read and write
fault benchmarks just measure fault time, they do not include I/O time.
* CONFIG_MEMCG not set:
baseline patched
kbuild 1m25.030000(+-0.088% 3 samples) 1m25.426667(+-0.120% 3 samples)
dd write 100 MiB 0.859211561 +-15.10% 0.874162885 +-15.03%
dd write 200 MiB 1.670653105 +-17.87% 1.669384764 +-11.99%
dd write 1000 MiB 8.434691190 +-14.15% 8.474733215 +-14.77%
read fault cycles 254.0(+-0.000% 10 samples) 253.0(+-0.000% 10 samples)
write fault cycles 2021.2(+-3.070% 10 samples) 1984.5(+-1.036% 10 samples)
* CONFIG_MEMCG=y root_memcg:
baseline patched
kbuild 1m25.716667(+-0.105% 3 samples) 1m25.686667(+-0.153% 3 samples)
dd write 100 MiB 0.855650830 +-14.90% 0.887557919 +-14.90%
dd write 200 MiB 1.688322953 +-12.72% 1.667682724 +-13.33%
dd write 1000 MiB 8.418601605 +-14.30% 8.673532299 +-15.00%
read fault cycles 266.0(+-0.000% 10 samples) 266.0(+-0.000% 10 samples)
write fault cycles 2051.7(+-1.349% 10 samples) 2049.6(+-1.686% 10 samples)
* CONFIG_MEMCG=y non-root_memcg:
baseline patched
kbuild 1m26.120000(+-0.273% 3 samples) 1m25.763333(+-0.127% 3 samples)
dd write 100 MiB 0.861723964 +-15.25% 0.818129350 +-14.82%
dd write 200 MiB 1.669887569 +-13.30% 1.698645885 +-13.27%
dd write 1000 MiB 8.383191730 +-14.65% 8.351742280 +-14.52%
read fault cycles 265.7(+-0.172% 10 samples) 267.0(+-0.000% 10 samples)
write fault cycles 2070.6(+-1.512% 10 samples) 2084.4(+-2.148% 10 samples)
As expected anon page faults are not affected by this patch.
tj: Updated to apply on top of the recent cancel_dirty_page() changes.
Signed-off-by: Sha Zhengju <handai.szj@gmail.com>
Signed-off-by: Greg Thelen <gthelen@google.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@fb.com>
This adds documentation of device tree bindings for the
STM32 timer.
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
This adds documentation of device tree bindings for the
ARM System timer.
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Add DT bindings documentation for lpc3220-timer. This timer is
used as clocksource on many NXP platforms.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
The usb-clk on sun8i a23 and a33 SoCs is similar to the ones found
on sun6i-a31 SoCs but instead of a 3th phy the a23 / a33 have a hsic
interface which gets enabled by almost the same bits as used on
the a31 for the 3rd phy, but not exactly the same bits so we need
a new compatible for this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
instead of returning '1' to indicate error - Dan Carpenter
* New support to expose the EFI System Resource Tables in sysfs, which
provides information for performing firmware updates - Peter Jones
* Documentation cleanup in the EFI handover protocol section which
falsely claimed that 'cmdline_size' needed to be filled out by the
boot loader - Alex Smith
* Align the order of SMBIOS tables in /sys/firmware/efi/systab to match
the way that we do things for ACPI and add documentation to
Documentation/ABI - Jean Delvare
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Twjn
-----END PGP SIGNATURE-----
Merge tag 'efi-next' of git://git.kernel.org/pub/scm/linux/kernel/git/mfleming/efi into x86/efi
Pull EFI changes from Matt Fleming:
- Use idiomatic negative error values in efivar_create_sysfs_entry()
instead of returning '1' to indicate error. (Dan Carpenter)
- Implement new support to expose the EFI System Resource Tables in sysfs,
which provides information for performing firmware updates. (Peter Jones)
- Documentation cleanup in the EFI handover protocol section which
falsely claimed that 'cmdline_size' needed to be filled out by the
boot loader. (Alex Smith)
- Align the order of SMBIOS tables in /sys/firmware/efi/systab to match
the way that we do things for ACPI and add documentation to
Documentation/ABI. (Jean Delvare)
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull RCU changes from Paul E. McKenney:
- Initialization/Kconfig updates: hide most Kconfig options from unsuspecting users.
There's now a single high level configuration option:
*
* RCU Subsystem
*
Make expert-level adjustments to RCU configuration (RCU_EXPERT) [N/y/?] (NEW)
Which if answered in the negative, leaves us with a single interactive
configuration option:
Offload RCU callback processing from boot-selected CPUs (RCU_NOCB_CPU) [N/y/?] (NEW)
All the rest of the RCU options are configured automatically.
- Remove all uses of RCU-protected array indexes: replace the
rcu_[access|dereference]_index_check() APIs with READ_ONCE() and rcu_lockdep_assert().
- RCU CPU-hotplug cleanups.
- Updates to Tiny RCU: a race fix and further code shrinkage.
- RCU torture-testing updates: fixes, speedups, cleanups and
documentation updates.
- Miscellaneous fixes.
- Documentation updates.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Conflicts:
drivers/net/phy/amd-xgbe-phy.c
drivers/net/wireless/iwlwifi/Kconfig
include/net/mac80211.h
iwlwifi/Kconfig and mac80211.h were both trivial overlapping
changes.
The drivers/net/phy/amd-xgbe-phy.c file got removed in 'net-next' and
the bug fix that happened on the 'net' side is already integrated
into the rest of the amd-xgbe driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
- dwc2 adds hibernation support
- preparation for sunxi glue to musb driver
- new ULPI bus
- new ULPI PHY driver for TUSB1210
- musb patches to support multiple DMA engines on same binary
- support for R-Car E2 on renesas_usbhs
Signed-off-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Jqzf
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v4.2 merge window
- dwc2 adds hibernation support
- preparation for sunxi glue to musb driver
- new ULPI bus
- new ULPI PHY driver for TUSB1210
- musb patches to support multiple DMA engines on same binary
- support for R-Car E2 on renesas_usbhs
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add the missing r8a7778-specific compatible value, which is already in
use since v4.1-rc1.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
- Document Snoop Control Unit (SCU) bindings
- Document Ux500 board bindings
- Define the backup RAM in the DBx500 device tree
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=IRmr
-----END PGP SIGNATURE-----
Merge tag 'dt-for-armsoc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into next/dt
Merge "Device Tree changes for Ux500 and ARM SOC" from Linus Walleij:
- Document Snoop Control Unit (SCU) bindings
- Document Ux500 board bindings
- Define the backup RAM in the DBx500 device tree
* tag 'dt-for-armsoc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
ARM: ux500: define the backupram in the device tree
ARM: ux500: add board documentation
ARM: scu: document Snoop Control Unit DT bindings
The Allwinner SoCs have a handful of SRAM that can be either mapped to be
accessible by devices or the CPU.
That mapping is controlled by an SRAM controller, and that mapping might
not be set by the bootloader, for example if the device wasn't used at all,
or if we're using solutions like the U-Boot's Falcon Boot.
We could also imagine changing this at runtime for example to change the
mapping of these SRAMs to use them for suspend/resume or runtime memory
rate change, if that ever happens.
These use cases require some API in the kernel to control that mapping,
exported through a drivers/soc driver.
This driver also implement a debugfs file that shows the SRAM found in the
system, the current mapping and the SRAM that have been claimed by some
drivers in the kernel.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This driver device one local attribute: vbus.
Describe that in Documentation/ABI/testing/sysfs-platform/twl4030-usb.
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The generic RZ CPG compatible value is mandatory, as the driver uses
only this value for matching. Document that this is a fallback that
must be present.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The generic R-Car Gen2 CPG compatible value is mandatory, as the driver
uses only this value for matching. Document that this is a fallback
that must be present.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The generic MSTP gate clocks compatible value is mandatory, as the
driver uses only this value for matching. Document that this is a
fallback that must be present.
Also fix a typo (missing plural "s") in the compatible value.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The generic CPG DIV6 clock compatible value is mandatory, as the driver
uses only this value for matching. Document that this is a fallback
that must be present.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The changeset dc9ef7d112 change the open() ioctl documentation to
match the V4L2 open(). However, some cut-and-pasted stuff doesn't
match what actually happens at the DVB core.
So, fix the documentation entry to be more accurate with the DVB
frontend open() specifics.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
To fix the last xmllint errors the open and close function reference
description was rewritten based on the v4l2 open and close functions.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Fixes a large number of xmllint errors.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Using specific compatible string in binding doc to make the binding
more clear.
It's also used to avoid checkpatch warning in the future like follows:
WARNING: DT compatible string "fsl,imx6sx-usdhc" appears un-documented --
check ./Documentation/devicetree/bindings/
+ { .compatible = "fsl,imx6sx-usdhc", .data = &usdhc_imx6sx_data, },
total: 0 errors, 1 warnings, 18 lines checked
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
MMCIF IP on R-Car series has parent clock which can be set several rate,
and it was not implemented on old SH-Mobile series (= SH-Mobile series
parent clock was fixed rate) R-Car series MMCIF can use more high speed
access if it setups parent clock. This patch adds parent clock setup
method. It will be used if DT has "max-frequency", and then, this driver
assumes it is booted on R-Car Gen2 or later SoC. Because SH-Mobile series
(which doesn't boot from DT) and R-Car series (which boots from DT) have
different divider.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Keita Kobayashi <keita.kobayashi.ym@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
[Ulf: Silence compiler warning]
Allow to specify in the device-tree that no physical write-protect signal
is connected to a particular instance of a MMC controller. Setting the
property will cause the core will assume that the SD card is always
read-write.
The name for the new property is 'disable-wp' and was chosen based on the
property with the same function from the Synopsys designware mobile storage
host controller DT bindings specification.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds the quirks and compatible string in sdhci-of-arasan.c
to support sdhci-arasan4.9a version of controller.
Signed-off-by: Suman Tripathi <stripathi@apm.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds support for the ntc thermistor NCPXXWF104 series.
Cc: Jean Delvare <jdelvare@suse.de>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Beomho Seo <beomho.seo@samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The mediatek SoCs have I2C controller that handle I2C transfer.
This patch include common I2C bus driver.
This driver is compatible with I2C controller on mt65xx/mt81xx.
Signed-off-by: Xudong Chen <xudong.chen@mediatek.com>
Signed-off-by: Liguo Zhang <liguo.zhang@mediatek.com>
Signed-off-by: Eddie Huang <eddie.huang@mediatek.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There was some confusion what was needed to utilize the slave support,
so let's be more precise about this. Add an introductory paragraph to
the development section while we are here.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add device tree binding documentation for nxp,lpc1850-uart.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Support command line parameters of the form:
earlycon=<name>,io|mmio|mmio32|mmio32be,<addr>,<options>
This commit seem to be needed even after commit:
serial: 8250: Add support for big-endian MMIO accesses
c627f2ceb6
Signed-off-by: Noam Camus <noamc@ezchip.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linux v3.20 was released as v4.0.
Signed-off-by: Fanael Linithien <fanael4@gmail.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Pull SCSI target fixes from Nicholas Bellinger:
"These are mostly minor fixes, with the exception of the following that
address fall-out from recent v4.1-rc1 changes:
- regression fix related to the big fabric API registration changes
and configfs_depend_item() usage, that required cherry-picking one
of HCH's patches from for-next to address the issue for v4.1 code.
- remaining TCM-USER -v2 related changes to enforce full CDB
passthrough from Andy + Ilias.
Also included is a target_core_pscsi driver fix from Andy that
addresses a long standing issue with a Scsi_Host reference being
leaked on PSCSI device shutdown"
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
iser-target: Fix error path in isert_create_pi_ctx()
target: Use a PASSTHROUGH flag instead of transport_types
target: Move passthrough CDB parsing into a common function
target/user: Only support full command pass-through
target/user: Update example code for new ABI requirements
target/pscsi: Don't leak scsi_host if hba is VIRTUAL_HOST
target: Fix se_tpg_tfo->tf_subsys regression + remove tf_subsystem
target: Drop signal_pending checks after interruptible lock acquire
target: Add missing parentheses
target: Fix bidi command handling
target/user: Disallow full passthrough (pass_level=0)
ISCSI: fix minor memory leak
- Fix sysfs attribute initialization in nct6775 and nct6683 drivers
- Do not attempt to auto-detect tmp435 on I2C address 0x37
- Ensure iio channel is of type IIO_VOLTAGE in ntc_thermistor driver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJVaQlBAAoJEMsfJm/On5mBLw8P/RWUBhL04n4dy7bw8Ap78XOo
vJBBK/viNonECxShAdyG2dP+/qgNI/1Zbd3ApaDuJKiqV36WdL7wb2/D+wDWxkZG
MRnxpQ4E67EifbdXZ0+xbIWv/VoHv7JafFS7E7t7GeXih7KophDj3xuMBcR85/Dt
89TA0+RyX4Cyk7WagXXa+7ybpYEa8DbsHRdPGxdddNh3+BC87/LUoOVgIshN/pv2
3bYYBo7de7jxR/Avf8G7VETxS/MrG6RTeZ6lM0QSAj4uRDPYR/dtkrVOpE6ZcGmh
+XjWJE0YWDFh4OEPheF2aXBhsZuakI055vLXrFJDomzJGdzIUnttZo2+IB9I/lI+
fzZslRtTdecF8ee9XJSOocNnLhV5WtNEg7zYbk7titSnp5zoNxM6fvHC5HkK+uTb
BgEtjgs+l8+BLXKAp7y92YUSvLt/esGbBr+AnscvRbcG//41FV1bY3zG3Xxh4tCV
cjg9WokSkIvvbxYqA6x4qr7WHTtruTxHtHkc9BKRzIjzrISm/HFKbBS80gQ6RGPm
YLK5eAMYuDCaRtsaPJAPx3Sqmzl+fCy2MAmcPz36OTqGhps/YtVmeQpCAqIuP2eu
8v/5rJU7rjs+OjJxPYeH630C7WeQK7Q09xWEYNoXMl2cqAjGJVka/tJFDF1Ru4+M
JdiRx1tia5AXu1aThx1h
=cHeh
-----END PGP SIGNATURE-----
Merge tag 'hwmon-for-linus-v4.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fixes from Guenter Roeck:
"Some late hwmon patches, all headed for -stable
- fix sysfs attribute initialization in nct6775 and nct6683 drivers
- do not attempt to auto-detect tmp435 on I2C address 0x37
- ensure iio channel is of type IIO_VOLTAGE in ntc_thermistor driver"
* tag 'hwmon-for-linus-v4.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (nct6683) Add missing sysfs attribute initialization
hwmon: (nct6775) Add missing sysfs attribute initialization
hwmon: (tmp401) Do not auto-detect chip on I2C address 0x37
hwmon: (ntc_thermistor) Ensure iio channel is of type IIO_VOLTAGE
Johan Hedberg says:
====================
pull request: bluetooth-next 2015-05-28
Here's a set of patches intended for 4.2. The majority of the changes
are on the 802.15.4 side of things rather than Bluetooth related:
- All sorts of cleanups & fixes to ieee802154 and related drivers
- Rework of tx power support in ieee802154 and its drivers
- Support for setting ieee802154 tx power through nl802154
- New IDs for the btusb driver
- Various cleanups & smaller fixes to btusb
- New btrtl driver for Realtec devices
- Fix suspend/resume for Realtek devices
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify target core and target drivers by storing the task tag
a.k.a. command identifier inside struct se_cmd.
For several transports (e.g. SRP) tags are 64 bits wide.
Hence add support for 64-bit tags.
(Fix core_tmr_abort_task conversion spec warnings - nab)
(Fix up usb-gadget to use 16-bit tags - HCH + bart)
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Andy Grover <agrover@redhat.com>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: <qla2xxx-upstream@qlogic.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Juergen Gross <jgross@suse.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Now that struct se_portal_group contains a protocol identifier field we can
take all the code to format an parse protocol identifiers in CDBs into common
code instead of leaving this to low-level drivers.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Now that we store the protocol identifier in the tpg structure we don't
need this method.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Remove the unneeded fabric_ptr argument, and change the type argument
to pass in a SPC protocol identifier.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
By always allocating and adding, respectively removing and freeing
the se_node_acl structure in core code we can remove tons of repeated
code in the init_nodeacl and drop_nodeacl routines. Additionally
this now respects the get_default_queue_depth method in this code
path as well.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
All fabric drivers except for iSCSI always return 1, so implement
that as default behavior.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Enable TCMU to handle bidirectional SCSI commands. In such cases,
entries in iov[] cover both the Data-In and the Data-Out buffers. The
first iov_cnt entries correspond to the Data-Out buffer, while the
remaining iov_bidi_cnt entries correspond to the Data-In buffer.
Signed-off-by: Ilias Tsitsimpis <iliastsi@arrikto.com>
Signed-off-by: Vangelis Koukis <vkoukis@arrikto.com>
Reviewed-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
After much discussion, give up on only passing a subset of SCSI commands
to userspace and pass them all. Based on what pscsi is doing, make sure
to set SCF_SCSI_DATA_CDB for I/O ops, and define attributes identical to
pscsi.
Make hw_block_size configurable via dev param.
Remove mention of command filtering from tcmu-design.txt.
Signed-off-by: Andy Grover <agrover@redhat.com>
Reviewed-by: Ilias Tsitsimpis <iliastsi@arrikto.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
We now require that the userspace handler set a bit if the command is not
handled.
Update calls to tcmu_hdr_get_op for v2.
Signed-off-by: Andy Grover <agrover@redhat.com>
Reviewed-by: Ilias Tsitsimpis <iliastsi@arrikto.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Add the device tree bindings documentation for the QCA IPQ806x
variant of the Synopsys DesignWare MAC.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Document this new colorspace define.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Document this new colorspace define.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This format was added but not documented. Do this now.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The DVB part of the media API documentation has several
legacy things on it:
- Examples that don't work;
- APIs unused and deprecated;
- places mentioning the wrong API version.
Fix them and bump the documentation version, in order to
reflect the cleanup efforts to make it more consistent with
the current status of the API.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Due to a cut-and-paste error, the argument is missing or wrong
on 3 ioctl documentation. Fix them.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The notes there are somewhat confusing and assumes that the
reader would have read the DVBv3 way. This is not true anymore,
as the DVBv3 is now on a separate section that is marked as
deprecated.
So, cleanup the notes.
While here, add a note about using libdvbv5, instead of using
the DVBv5 API directly.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
In order to make it clearer about how to use the DVBv5 calls,
add an example of its usage. That should make it clearer about
what's actually required for the DVBv5 calls to work.
While here, also mentions the libdvbv5 library.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Rename the tytle of the struct documentation to reflect
the name of the structures, and use links to do cross-ref.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
fe_bandwidth/fe_bandwidth_t is used only on DVBv3 API. So, move
it to the frontend legacy xml, and convert it into a table.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
At frontend legacy API description, there are three places
where fe_modulation_t is defined. Cross-reference it to point
to the right place at the documentation.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The typedef parser is wrong and doesn't get some of the
types defined at the DVB API. Improve it, as we want to add
cross-references to those types.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There are a few issues at FE_GET_INFO documentation:
- name is a string, not a pointer to a string;
- the return text should be after the paragraph.
While here, better to bold that two fields of the structure used
by FE_GET_INFO are actually deprecated.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Instead of using programlisting, use a table, as this provides
a better view of the structure.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The fe_type is deprecated at the DVB API. However, it may still
be used by legacy DVBv3 applications. While this works with old
devices, modern devices may support more than one delivery
system.
Add an explanation about that and a point to what should be
used, instead, in order for legacy apps to support newer hardware.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Instead of just showing ioctls, let's add an introdutory text
briefly explaining the DVB frontend API.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
What's written there about the arguments for this ioctl
is bogus: it doesn't return an enum (or a typedef)
for enum fe_status. Instead, it returns a bitmask with the
values defined by enum fe_status.
Also, the size of the integer returned is not 16 bits, but,
instead, sizeof(fe_status_t), e. g. sizeof(enum), with is
arch-dependent.
This should of course be fixed, but this should be done on
a separate patch.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Move the function ioctl definitions to the end of the chapter,
at their importance. That makes the document better organized,
as the DVB frontend system call index will look like:
open()
close()
ioctl FE_GET_INFO — Query DVB frontend capabilities and returns information about the front-end. This call only requires read-only access to the device
ioctl FE_READ_STATUS — Returns status information about the front-end. This call only requires read-only access to the device
ioctl FE_SET_PROPERTY, FE_GET_PROPERTY — FE_SET_PROPERTY sets one or more frontend properties. FE_GET_PROPERTY returns one or more frontend properties.
ioctl FE_DISEQC_RESET_OVERLOAD — Restores the power to the antenna subsystem, if it was powered off due to power overload.
ioctl FE_DISEQC_SEND_MASTER_CMD — Sends a DiSEqC command
ioctl FE_DISEQC_RECV_SLAVE_REPLY — Receives reply from a DiSEqC 2.0 command
ioctl FE_DISEQC_SEND_BURST — Sends a 22KHz tone burst for 2x1 mini DiSEqC satellite selection.
ioctl FE_SET_TONE — Sets/resets the generation of the continuous 22kHz tone.
ioctl FE_SET_VOLTAGE — Allow setting the DC level sent to the antenna subsystem.
ioctl FE_ENABLE_HIGH_LNB_VOLTAGE — Select output DC level between normal LNBf voltages or higher LNBf voltages.
ioctl FE_SET_FRONTEND_TUNE_MODE — Allow setting tuner mode flags to the frontend.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Use the new format for the ioctl documentation and put the
struct dvb_diseqc_slave_reply together with the ioctl.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Use the new format for the ioctl documentation and put the
struct dvb_diseqc_slave_reply together with the ioctl.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Use the new format for the ioctl documentation and put the
struct dvb_diseqc_slave_reply together with the ioctl.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Use the proper format for FE_DISEQC_SEND_BURST documentation
and improve the documentation.
Keep the enum fe_sec_mini_cmd description together with
the ioctl, as both are used together.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Use the proper format for FE_SET_TONE documentation and
improve the documentation.
Keep the enum fe_sec_tone_mode description together with
the ioctl, as both are used together.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Use the proper format for FE_SET_VOLTAGE documentation and fix
the documentation. The description for the enum is not 100%,
and it is missing the voltage off value.
Also, it is better to keep the enum description together with
the ioctl, as both are used together.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
That helps the xref logic at the Makefile to point to the
right place. Also, it becomes more organized and easier to
maintain if each ioctl have its own xml file.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
for the xml files describing ioctls, use the same nomenclature
as on V4L2: the ioctl name, in lower case, using - instead of _.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The new code that detects undocumented ioctls hits some false
positives:
This one is not documented, nor it should, as this is
there just to reserve namespace:
Warning: can't find reference for VIDIOC_RESERVED ioctl
But those are already documented together with other ioctls:
Warning: can't find reference for VIDIOC_UNSUBSCRIBE_EVENT ioctl
Warning: can't find reference for FE_GET_PROPERTY ioctl
Warning: can't find reference for VIDIOC_SUBDEV_G_EDID ioctl
Warning: can't find reference for VIDIOC_SUBDEV_S_EDID ioctl
Warning: can't find reference for VIDIOC_SUBDEV_S_DV_TIMINGS ioctl
Warning: can't find reference for VIDIOC_SUBDEV_G_DV_TIMINGS ioctl
Warning: can't find reference for VIDIOC_SUBDEV_QUERY_DV_TIMINGS ioctl
So, we need to just be sure to point to the right documentation.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There are several badly documented undocumented ioctls.
Currently, it just generates an empty link. Instead of doing that,
only add references to the ones that exists, and add a warning
for all references that weren't found.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Create xref links for all DTV properties and link the frontend.h
to each. Also use them at the DVB frontent API example.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Instead of having two refentries, merge them into just one,
like what's done with other similar ioctls at V4L2 side.
That makes the entry cleaner and will allow to add the associated
structures together with the refentry.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Instead of going to the V4L2 open(), use the xref to the
proper place at the frontend ioctls that were already
reformatted.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The DVBv5 API uses DVB properties as the main way to set the frontend
and collect statistics. Move the definition to happen earlier, in
order to reflect its importance.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Move the ioctl and enum fe_status to a separate xml file and
put it into a better format.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Keeping everything altogether makes harder to reorganize the
DocBook. So, move the FE_GET_INFO ioctl and the associated structures
into a separate file.
No functional changes.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The DVB part of the docbook has a completely different format
than the V4L2 part, as it was written as a separate document.
As the V4L2 documentation is on better shape, and its format
allows adding more information, let's use it for FE_GET_INFO
and gradually update the non-legacy DVB ioctls using the new
format.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Although the recommended usage is the DVBv5 API calls, the
documentation doesn't make it clear about what's the recommended
calls and what's legacy.
So, move the legacy API bits to a separate xml, putting them into
a new section.
Please notice that more changes are needed, since some of the
bits there are cross-referenced elsewhere.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Currently, it is using 'role="tt"', but this is not defined at
the DocBook 4.5 spec. The net result is that no emphasis happens.
So, replace them to bold emphasis.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
An illustration of what's considered a typical media device
may help people to better understand the contents of the media
infrastructure API docbook. So, add it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The Docbook mistakenly makes to believe that all needed APIs for
media devices are there. Add a note there pointing that some
sub-devices are actually be controlled via ALSA API.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The list of standards at the media docbook is incomplete, and it
is mentioning that the DVB-S2 & friends is "currently being updated".
That's wrong, as such update occurred back in 2008.
So, provide a more complete list of supported standards and add
a reference to the actual list.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
David Woodhouse
Wei Chen
Samuel Thibault
Kevin Hilman
Jun Nie
Vincent Cuissard
Joe Thornber
Stephane Viau
Hai Li
Lee Jones
Sergei Shtylyov
Alexey Kardashevskiy
Greg Kroah-Hartman
Zhang Rui
Hauke Mehrtens
Jacek Anaszewski
Mark Brown
Oder Chiou
Srinivas Kandagatla
Lior Amsalem
Krzysztof Kozlowski
Kamal Dasu
Cyrille Pitchen
Thomas Petazzoni
Christophe Ricard
Bjorn Andersson
Anurag Kumar Vulisha
Rabin Vincent
Tony Lindgren
Suneel Garapati
Mauro Carvalho Chehab
Dmitry Eremin-Solenikov
Fabien Dessenne
Rob Herring
Laxman Dewangan
Masanari Iida
Lubomir Rintel
Dave Hansen
Tang Yuantian
David S. Miller
Jonathan Corbet
Thomas de Beauchene
Dan Murphy
Jeffrey Rogers
Pali Rohár
Krzysztof Kozlowski
Linus Walleij
Mark A. Greer
Linus Torvalds
Ingo Molnar
Takashi Iwai
Peter Ujfalusi
Hao Liu
Stefan Agner
Ashok Raj
Toshi Kani
Anshuman Khandual
Hans Verkuil
Hans Verkuil
Stephen Boyd
Carlo Caione
Duc Dang
Geert Uytterhoeven
Paolo Bonzini
Bintian Wang
Tomi Valkeinen
Igal Liberman
Andreas Gruenbacher
Frans Klaver
Prarit Bhargava
Luis R. Rodriguez
Rojhalat Ibrahim
Vishnu Patekar
Scott Feldman
Dave Airlie
kongxinwei
Mike Looijmans
Boris Brezillon
James Morris
Frank Li
Michael Neuling
Vaibhav Jain
Stephan Mueller
Scott Wood
Kukjin Kim
Alan Tull
Rafal Krypa
Fang, Yang A
Arnd Bergmann
Ard Biesheuvel
Seymour, Shane M
Bart Van Assche
Greg Thelen
Maxime Coquelin
Joachim Eastwood
Hans de Goede
Maxime Ripard
NeilBrown
Ulrich Hecht
Dong Aisheng
Kuninori Morimoto
Zhangfei Gao
Lars-Peter Clausen
Suman Tripathi
Beomho Seo
Xudong Chen
Wolfram Sang
Noam Camus
Rama Kiran Kumar Indrakanti
Fanael Linithien
Christoph Hellwig
Ilias Tsitsimpis
Andy Grover
Mathieu Olivari