For SoC to achieve its lowest power platform idle state a set of hardware
preconditions must be met. These preconditions or constraints can be
obtained by issuing a device specific method (_DSM) with function "1".
Refer to the document provided in the link below.
Here during initialization (from attach() callback of LPS0 device), invoke
function 1 to get the device constraints. Each enabled constraint is
stored in a table.
The devices in this table are used to check whether they were in required
minimum state, while entering suspend. This check is done from platform
freeze wake() callback, only when /sys/power/pm_debug_messages attribute
is non zero.
If any constraint is not met and device is ACPI power managed then it
prints the device information to kernel logs.
Also if debug is enabled in acpi/sleep.c, the constraint table and state
of each device on wake is dumped in kernel logs.
Since pm_debug_messages_on setting is used as condition to check
constraints outside kernel/power/main.c, pm_debug_messages_on is changed
to a global variable.
Link: http://www.uefi.org/sites/default/files/resources/Intel_ACPI_Low_Power_S0_Idle.pdf
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Rename struct platform_freeze_ops to platform_s2idle_ops to make it
clear that the callbacks in it are used during suspend-to-idle
suspend/resume transitions and rename the related functions,
variables and so on accordingly.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
To make it clear that the symbol in question refers to
suspend-to-idle, rename it from PM_SUSPEND_FREEZE to
PM_SUSPEND_TO_IDLE.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Modify the ACPI system sleep support setup code to select
suspend-to-idle as the default system sleep state if
(1) the ACPI_FADT_LOW_POWER_S0 flag is set in the FADT and
(2) the Low Power Idle S0 _DSM interface has been discovered and
(3) the default sleep state was not selected from the kernel command
line.
The main motivation for this change is that systems where the (1) and
(2) conditions are met typically ship with OSes that don't exercise
the S3 path in the platform firmware which remains untested and turns
out to be non-functional at least in some cases.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Mario Limonciello <mario.limonciello@dell.com>
Function acpi_sleep_syscore_init has no external user so it should be
static.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit eed4d47efe (ACPI / sleep: Ignore spurious SCI wakeups from
suspend-to-idle) introduced acpi_freeze_sync() whose purpose is to
flush all of the processing of possible wakeup events signaled via
the ACPI SCI. However, it doesn't flush the query workqueue used
by the EC driver, so the events generated by the EC may not be
processed timely which leads to issues (increased overhead at least,
lost events possibly).
To fix that introduce acpi_ec_flush_work() that will flush all of
the outstanding EC work and call it from acpi_freeze_sync().
Fixes: eed4d47efe (ACPI / sleep: Ignore spurious SCI wakeups from suspend-to-idle)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Some recent Dell laptops, including the XPS13 model numbers 9360 and
9365, cannot be woken up from suspend-to-idle by pressing the power
button which is unexpected and makes that feature less usable on
those systems. Moreover, on the 9365 ACPI S3 (suspend-to-RAM) is
not expected to be used at all (the OS these systems ship with never
exercises the ACPI S3 path in the firmware) and suspend-to-idle is
the only viable system suspend mechanism there.
The reason why the power button wakeup from suspend-to-idle doesn't
work on those systems is because their power button events are
signaled by the EC (Embedded Controller), whose GPE (General Purpose
Event) line is disabled during suspend-to-idle transitions in Linux.
That is done on purpose, because in general the EC tends to be noisy
for various reasons (battery and thermal updates and similar, for
example) and all events signaled by it would kick the CPUs out of
deep idle states while in suspend-to-idle, which effectively might
defeat its purpose.
Of course, on the Dell systems in question the EC GPE must be enabled
during suspend-to-idle transitions for the button press events to
be signaled while suspended at all, but fortunately there is a way
out of this puzzle.
First of all, those systems have the ACPI_FADT_LOW_POWER_S0 flag set
in their ACPI tables, which means that the OS is expected to prefer
the "low power S0 idle" system state over ACPI S3 on them. That
causes the most recent versions of other OSes to simply ignore ACPI
S3 on those systems, so it is reasonable to expect that it should not
be necessary to block GPEs during suspend-to-idle on them.
Second, in addition to that, the systems in question provide a special
firmware interface that can be used to indicate to the platform that
the OS is transitioning into a system-wide low-power state in which
certain types of activity are not desirable or that it is leaving
such a state and that (in principle) should allow the platform to
adjust its operation mode accordingly.
That interface is a special _DSM object under a System Power
Management Controller device (PNP0D80). The expected way to use it
is to invoke function 0 from it on system initialization, functions
3 and 5 during suspend transitions and functions 4 and 6 during
resume transitions (to reverse the actions carried out by the
former). In particular, function 5 from the "Low-Power S0" device
_DSM is expected to cause the platform to put itself into a low-power
operation mode which should include making the EC less verbose (so to
speak). Next, on resume, function 6 switches the platform back to
the "working-state" operation mode.
In accordance with the above, modify the ACPI suspend-to-idle code
to look for the "Low-Power S0" _DSM interface on platforms with the
ACPI_FADT_LOW_POWER_S0 flag set in the ACPI tables. If it's there,
use it during suspend-to-idle transitions as prescribed and avoid
changing the GPE configuration in that case. [That should reflect
what the most recent versions of other OSes do.]
Also modify the ACPI EC driver to make it handle events during
suspend-to-idle in the usual way if the "Low-Power S0" _DSM interface
is going to be used to make the power button events work while
suspended on the Dell machines mentioned above
Link: http://www.uefi.org/sites/default/files/resources/Intel_ACPI_Low_Power_S0_Idle.pdf
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The ACPI SCI (System Control Interrupt) is set up as a wakeup IRQ
during suspend-to-idle transitions and, consequently, any events
signaled through it wake up the system from that state. However,
on some systems some of the events signaled via the ACPI SCI while
suspended to idle should not cause the system to wake up. In fact,
quite often they should just be discarded.
Arguably, systems should not resume entirely on such events, but in
order to decide which events really should cause the system to resume
and which are spurious, it is necessary to resume up to the point
when ACPI SCIs are actually handled and processed, which is after
executing dpm_resume_noirq() in the system resume path.
For this reasons, add a loop around freeze_enter() in which the
platforms can process events signaled via multiplexed IRQ lines
like the ACPI SCI and add suspend-to-idle hooks that can be
used for this purpose to struct platform_freeze_ops.
In the ACPI case, the ->wake hook is used for checking if the SCI
has triggered while suspended and deferring the interrupt-induced
system wakeup until the events signaled through it are actually
processed sufficiently to decide whether or not the system should
resume. In turn, the ->sync hook allows all of the relevant event
queues to be flushed so as to prevent events from being missed due
to race conditions.
In addition to that, some ACPI code processing wakeup events needs
to be modified to use the "hard" version of wakeup triggers, so that
it will cause a system resume to happen on device-induced wakeup
events even if the "soft" mechanism to prevent the system from
suspending is not enabled. However, to preserve the existing
behavior with respect to suspend-to-RAM, this only is done in
the suspend-to-idle case and only if an SCI has occurred while
suspended.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The wakeup.flags.enabled flag in struct acpi_device is not used
consistently, as there is no reason why it should only apply
to the enabling/disabling of the wakeup GPE, so put the invocation
of acpi_enable_wakeup_device_power() under it too.
Moreover, it is not necessary to call
acpi_enable_wakeup_devices() and acpi_disable_wakeup_devices() for
suspend-to-idle, so don't do that.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Revert commit eed4d47efe (ACPI / sleep: Ignore spurious SCI wakeups
from suspend-to-idle) as it turned out to be premature and triggered
a number of different issues on various systems.
That includes, but is not limited to, premature suspend-to-RAM aborts
on Dell XPS 13 (9343) reported by Dominik.
The issue the commit in question attempted to address is real and
will need to be taken care of going forward, but evidently more work
is needed for this purpose.
Reported-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
- Update the ACPICA code in the kernel to upstream revision
20170303 which includes:
* Minor fixes and improvements in the core code (Bob Moore,
Seunghun Han).
* Debugger fixes (Colin Ian King, Lv Zheng).
* Compiler/disassembler improvements (Bob Moore, David Box,
Lv Zheng).
* Build-related update (Lv Zheng).
- Add new device IDs and platform-related information to the
ACPI drivers for Intel (LPSS) and AMD (APD) SoCs (Hanjun Guo,
Hans de Goede).
- Make it possible to quirk ACPI-enumerated devices as "always
present" on platforms where they are incorrectly reported as not
present by the AML and add the INT0002 device ID to the list of
"always present" devices (Hans de Goede).
- Fix the register information in the xpower PMIC driver and add
comments to map the registers to symbols used by AML to it
(Hans de Goede).
- Move the code turning off unused ACPI power resources during
system resume to a point after all devices have been resumed
to avoid issues with power resources that do not behave as
expected (Hans de Goede).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=Ytsi
-----END PGP SIGNATURE-----
Merge tag 'acpi-extra-4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI updates from Rafael Wysocki:
"These update the ACPICA code in the kernel to upstream revision
20170303 which adds a few minor fixes and improvements, update ACPI
SoC drivers with new device IDs, platform-related information and
similar, fix the register information in the xpower PMIC driver,
introduce a concept of "always present" devices to the ACPI device
enumeration code and use it to fix a problem with one platform, and
fix a system resume issue related to power resources.
Specifics:
- Update the ACPICA code in the kernel to upstream revision 20170303
which includes:
* Minor fixes and improvements in the core code (Bob Moore,
Seunghun Han).
* Debugger fixes (Colin Ian King, Lv Zheng).
* Compiler/disassembler improvements (Bob Moore, David Box, Lv
Zheng).
* Build-related update (Lv Zheng).
- Add new device IDs and platform-related information to the ACPI
drivers for Intel (LPSS) and AMD (APD) SoCs (Hanjun Guo, Hans de
Goede).
- Make it possible to quirk ACPI-enumerated devices as "always
present" on platforms where they are incorrectly reported as not
present by the AML and add the INT0002 device ID to the list of
"always present" devices (Hans de Goede).
- Fix the register information in the xpower PMIC driver and add
comments to map the registers to symbols used by AML to it (Hans de
Goede).
- Move the code turning off unused ACPI power resources during system
resume to a point after all devices have been resumed to avoid
issues with power resources that do not behave as expected (Hans de
Goede)"
* tag 'acpi-extra-4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (22 commits)
ACPI / power: Delay turning off unused power resources after suspend
ACPI / PMIC: xpower: Fix power_table addresses
ACPI / LPSS: Call pwm_add_table() for Bay Trail PWM device
ACPICA: Update version to 20170303
ACPICA: iasl: add ASL conversion tool
ACPICA: Local cache support: Allow small cache objects
ACPICA: Disassembler: Do not unconditionally remove temporary names
ACPICA: iasl: Fix IORT SMMU GSI disassembling
ACPICA: Cleanup AML opcode definitions, no functional change
ACPICA: Debugger: Add interpreter blocking mark for single-step mode
ACPICA: debugger: fix memory leak on Pathname
ACPICA: Update for automatic repair code for objects returned by evaluate_object
ACPICA: Namespace: fix operand cache leak
ACPICA: Fix several incorrect invocations of ACPICA return macro
ACPICA: Fix a module for excessive debug output
ACPICA: Update some function headers, no funtional change
ACPICA: Disassembler: Enhance resource descriptor detection
i2c: designware: Add ACPI HID for Hisilicon Hip07/08 I2C controller
ACPI / APD: Add clock frequency for Hisilicon Hip07/08 I2C controller
ACPI / bus: Add INT0002 to list of always-present devices
...
The ACPI SCI (System Control Interrupt) is set up as a wakeup IRQ
during suspend-to-idle transitions and, consequently, any events
signaled through it wake up the system from that state. However,
on some systems some of the events signaled via the ACPI SCI while
suspended to idle should not cause the system to wake up. In fact,
quite often they should just be discarded.
Arguably, systems should not resume entirely on such events, but in
order to decide which events really should cause the system to resume
and which are spurious, it is necessary to resume up to the point
when ACPI SCIs are actually handled and processed, which is after
executing dpm_resume_noirq() in the system resume path.
For this reasons, add a loop around freeze_enter() in which the
platforms can process events signaled via multiplexed IRQ lines
like the ACPI SCI and add suspend-to-idle hooks that can be
used for this purpose to struct platform_freeze_ops.
In the ACPI case, the ->wake hook is used for checking if the SCI
has triggered while suspended and deferring the interrupt-induced
system wakeup until the events signaled through it are actually
processed sufficiently to decide whether or not the system should
resume. In turn, the ->sync hook allows all of the relevant event
queues to be flushed so as to prevent events from being missed due
to race conditions.
In addition to that, some ACPI code processing wakeup events needs
to be modified to use the "hard" version of wakeup triggers, so that
it will cause a system resume to happen on device-induced wakeup
events even if the "soft" mechanism to prevent the system from
suspending is not enabled (that also helps to catch device-induced
wakeup events occurring during suspend transitions in progress).
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit 660b1113e0 (ACPI / PM: Fix consistency check for power resources
during resume) introduced a check for ACPI power resources which have
been turned on by the BIOS during suspend and turns these back off again.
This is causing problems on a Dell Venue Pro 11 7130 (i5-4300Y) it causes
the following messages to show up in dmesg:
[ 131.014605] ACPI: Waking up from system sleep state S3
[ 131.150271] acpi LNXPOWER:07: Turning OFF
[ 131.150323] acpi LNXPOWER:06: Turning OFF
[ 131.150911] acpi LNXPOWER:00: Turning OFF
[ 131.169014] ACPI : EC: interrupt unblocked
[ 131.181811] xhci_hcd 0000:00:14.0: System wakeup disabled by ACPI
[ 133.535728] pci_raw_set_power_state: 76 callbacks suppressed
[ 133.535735] iwlwifi 0000:01:00.0: Refused to change power state,
currently in D3
[ 133.597672] PM: noirq resume of devices complete after 2428.891 msecs
Followed by a bunch of iwlwifi errors later on and the pcie device
dropping from the bus (acpiphp thinks it has been unplugged).
Disabling the turning off of unused power resources fixes this. Instead
of adding a quirk for this system, this commit fixes this by moving the
disabling of unused power resources to later in the resume sequence
when the iwlwifi card has been moved out of D3 so the ref_count for
its power resource no longer is 0.
This new behavior seems to match the intend of the original commit which
commit-msg says: "(... which means that no devices are going to need them
any time soon) and we should turn them off".
This also avoids power resources which we need when bringing devices out
of D3 from getting bounced off and then back on again.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In commit 821d6f0359 (ACPI / sleep: Do not save NVS for new machines to
accelerate S3), to optimize S3 suspend/resume speed, code is introduced
to ignore NVS memory saving during S3 for all the platforms later than
2012.
But, Lenovo G50-45, a platform released in 2015, still needs NVS memory
saving during S3. A quirk is introduced for this platform.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=189431
Tested-by: Przemek <soprwa@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
[ rjw: Drop unnecessary code ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Revert commit 08b98d3291 (PM / sleep / ACPI: Use the ACPI_FADT_LOW_POWER_S0
flag) as it caused system suspend (in the default configuration) to fail
on Dell XPS13 (9360) with the Kaby Lake processor.
Fixes: 08b98d3291 (PM / sleep / ACPI: Use the ACPI_FADT_LOW_POWER_S0 flag)
Reported-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Modify the ACPI system sleep support setup code to select
suspend-to-idle as the default system sleep state if the
ACPI_FADT_LOW_POWER_S0 flag is set in the FADT and the
default sleep state was not selected from the kernel command
line.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Mario Limonciello <mario.limonciello@dell.com>
Revert commit 2c85025c75 (ACPI: Execute _PTS before system reboot)
as it is reported to cause poweroff and reboot to hang on Dell
Latitude E7250.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=187061
Reported-by: Gianpaolo <gianpaoloc@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* acpi-wdat:
watchdog: wdat_wdt: Fix warning for using 0 as NULL
watchdog: wdat_wdt: fix return value check in wdat_wdt_probe()
platform/x86: intel_pmc_ipc: Do not create iTCO watchdog when WDAT table exists
i2c: i801: Do not create iTCO watchdog when WDAT table exists
mfd: lpc_ich: Do not create iTCO watchdog when WDAT table exists
ACPI / watchdog: Add support for WDAT hardware watchdog
* acpi-ec:
ACPI / EC: Fix issues related to boot_ec
ACPI / EC: Fix a gap that ECDT EC cannot handle EC events
ACPI / EC: Fix a memory leakage issue in acpi_ec_add()
ACPI / EC: Cleanup first_ec/boot_ec code
ACPI / EC: Enable event freeze mode to improve event handling for suspend process
ACPI / EC: Add PM operations to improve event handling for suspend process
ACPI / EC: Add PM operations to improve event handling for resume process
ACPI / EC: Fix an issue that SCI_EVT cannot be detected after event is enabled
ACPI / EC: Add EC_FLAGS_QUERY_ENABLED to reveal a hidden logic
ACPI / EC: Add PM operations for suspend/resume noirq stage
This patch makes 2 changes:
1. Restore old behavior
Originally, EC driver stops handling both events and transactions in
acpi_ec_block_transactions(), and restarts to handle transactions in
acpi_ec_unblock_transactions_early(), restarts to handle both events and
transactions in acpi_ec_unblock_transactions().
While currently, EC driver still stops handling both events and
transactions in acpi_ec_block_transactions(), but restarts to handle both
events and transactions in acpi_ec_unblock_transactions_early().
This patch tries to restore the old behavior by dropping
__acpi_ec_enable_event() from acpi_unblock_transactions_early().
2. Improve old behavior
However this still cannot fix the real issue as both of the
acpi_ec_unblock_xxx() functions are invoked in the noirq stage. Since the
EC driver actually doesn't implement the event handling in the polling
mode, re-enabling the event handling too early in the noirq stage could
result in the problem that if there is no triggering source causing
advance_transaction() to be invoked, pending SCI_EVT cannot be detected by
the EC driver and _Qxx cannot be triggered.
It actually makes sense to restart the event handling in any point during
resuming after the noirq stage. Just like the boot stage where the event
handling is enabled in .add(), this patch further moves
acpi_ec_enable_event() to .resume(). After doing that, the following 2
functions can be combined:
acpi_ec_unblock_transactions_early()/acpi_ec_unblock_transactions().
The differences of the event handling availability between the old behavior
(this patch isn't applied) and the new behavior (this patch is applied) are
as follows:
!Applied Applied
before suspend Y Y
suspend before EC Y Y
suspend after EC Y Y
suspend_late Y Y
suspend_noirq Y (actually N) Y (actually N)
resume_noirq Y (actually N) Y (actually N)
resume_late Y (actually N) Y (actually N)
resume before EC Y (actually N) Y (actually N)
resume after EC Y (actually N) Y
after resume Y (actually N) Y
Where "actually N" means if there is no triggering source, the EC driver
is actually not able to notice the pending SCI_EVT occurred in the noirq
stage. So we can clearly see that this patch has improved the situation.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Tested-by: Todd E Brandt <todd.e.brandt@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Now GPE can be masked via the new acpi_mask_gpe() API and this patch
modifies /sys/firmware/acpi/interrupts/gpexx to use this new facility.
Writes "mask/unmask" to this file now invokes acpi_mask_gpe().
Reads from this file now returns new "EN/STS" when the corresponding GPE
hardware register's EN/STS bits are flagged, and new "masked/unmasked"
attribute to indicate the status of the masking mechanism.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
[ rjw: Subject ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The _PTS control method is defined in the section 7.4.1 of acpi 6.0
spec. The _PTS control method is executed by the OS during the sleep
transition process for S1, S2, S3, S4, and for orderly S5 shutdown.
The _PTS control method provides the BIOS a mechanism for performing
some housekeeping, such as writing the sleep type value to the embedded
controller, before entering the system sleeping state. Note that some
Lenovo Server BIOS use this mechanism to detect reboot event and
prompt user by popped dialog box.
According to section 7.5 of acpi 6.0 spec, _PTS should run after _TTS.
Add a _PTS evaulation to the existing _TTS reboot notifier and change
the notifier name to reflect the fact that it's not for _TTS only any
more.
Signed-off-by: Ocean He <hehy1@lenovo.com>
Signed-off-by: Nagananda Chumbalkar <nchumbalkar@lenovo.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The problem is Linux registers pm_power_off = efi_power_off only if
we are in hardware reduced mode. Actually, what we also want is to do
this when ACPI S5 is simply not supported on non-legacy platforms.
Since some future Intel platforms are HW-full mode where the DSDT
fails to supply an _S5 object(without SLP_TYP), we should let such
kind of platform to leverage efi runtime service to poweroff.
This patch uses efi power off as first choice when S5 is unavailable,
even if there is a customized poweroff(driver provided, eg).
Meanwhile, the legacy platforms will not be affected because there is
no path for them to overwrite the pm_power_off to efi power off.
Suggested-by: Len Brown <len.brown@intel.com>
Reviewed-by: Matt Fleming <matt@codeblueprint.co.uk>
Signed-off-by: Chen Yu <yu.c.chen@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit 58a1fbbb2e ("PM / PCI / ACPI: Kick devices that might have been
reset by firmware") added a runtime resume for devices that were runtime
suspended when the system entered suspend-to-RAM.
Briefly, the motivation was to ensure that devices did not remain in a
reset-power-on state after resume, potentially preventing deep SoC-wide
low-power states from being entered on idle.
Currently we're not doing the same when leaving suspend-to-disk and this
asymmetry is a problem if drivers rely on the automatic resume triggered
by pm_complete_with_resume_check(). Fix it.
Fixes: 58a1fbbb2e (PM / PCI / ACPI: Kick devices that might have been reset by firmware)
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: 4.4+ <stable@vger.kernel.org> # 4.4+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
acpi_processor_sleep is neither related nor used by CPUIdle framework.
It's used in system suspend/resume path as a syscore operation. It makes
more sense to move it to acpi/sleep.c where all the S-state transition
(a.k.a. Linux system suspend/hiberate) related code are present.
Also make it depend on CONFIG_ACPI_SYSTEM_POWER_STATES_SUPPORT so that
it's not compiled on architecture like ARM64 where S-states are not
yet defined in ACPI.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit f06147f9fb (ACPICA: Hardware: Enable firmware waking vector
for both 32-bit and 64-bit FACS) added three functions that aren't
present in upstream ACPICA, acpi_hw_set_firmware_waking_vectors(),
acpi_set_firmware_waking_vectors() and acpi_set_firmware_waking_vector64(),
to allow Linux to use the previously existing API for setting the
platform firmware waking vector.
However, that wasn't necessary, since the ACPI sleep support code
in Linux can be modified to use the upstream ACPICA's API easily
and the additional functions may be dropped which reduces the code
size and puts the kernel's ACPICA code more in line with the upstream.
Make the changes as per the above. While at it, make the relevant
function desctiption comments reflect the upstream ACPICA's ones.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Lv Zheng <lv.zheng@intel.com>
* pm-sleep:
PM / hibernate: fix a comment typo
input: i8042: Avoid resetting controller on system suspend/resume
PM / PCI / ACPI: Kick devices that might have been reset by firmware
PM / sleep: Add flags to indicate platform firmware involvement
PM / sleep: Drop pm_request_idle() from pm_generic_complete()
PCI / PM: Avoid resuming more devices during system suspend
PM / wakeup: wakeup_source_create: use kstrdup_const
PM / sleep: Report interrupt that caused system wakeup
For an ACPI compatible system, the SCI (ACPI System Control
Interrupt) is used to wake the system up from suspend-to-idle.
Once the CPU is woken up by the SCI, the interrupt handler will
first check if the current IRQ has been configured for system
wakeup, so irq_pm_check_wakeup() is invoked to validate the IRQ
number. However, during suspend-to-idle, enable_irq_wake() is
called for acpi_gbl_FADT.sci_interrupt, although the IRQ number
that the SCI handler has been installed for should be passed to
it instead. Thus, if acpi_gbl_FADT.sci_interrupt happens to be
different from that number, ACPI interrupts will not be able to
wake up the system from sleep.
Fix this problem by passing the IRQ number returned by
acpi_gsi_to_irq() to enable_irq_wake() instead of
acpi_gbl_FADT.sci_interrupt.
Cc: 3.18+ <stable@vger.kernel.org> # 3.18+
Acked-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Chen Yu <yu.c.chen@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There are quite a few cases in which device drivers, bus types or
even the PM core itself may benefit from knowing whether or not
the platform firmware will be involved in the upcoming system power
transition (during system suspend) or whether or not it was involved
in it (during system resume).
For this reason, introduce global system suspend flags that can be
used by the platform code to expose that information for the benefit
of the other parts of the kernel and make the ACPI core set them
as appropriate.
Users of the new flags will be added later.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Currently, in suspend-to-idle, wakeup GPE for PCI devices are
handled properly because acpi_pci_sleep_wake() invokes acpi_enable_gpe()
to enable the wakeup GPE directly. But for the other wakeup-capable
devices in ACPI bus, acpi_enable_wakeup_devices() should be invoked
to update enable_for_wake mask in gpe_register_info structure, thus
acpi_enable_all_wakeup_gpes() can enable the wakeup GPE referred in
_PRW methods. And acpi_disable_wakeup_devices() will be called
before disable_irq_wake() in acpi_freeze_restore() to restore the mask.
This patch fixes a power button wakeup problem on Surface Pro 3,
on which platform power button uses EC to deliver event
(EC GPE is referred in _PRW).
Note: enabling EC GPE during freeze state may bring some risks
because EC events are expected to fire more frequently than others.
Thus it may bring the system out of freeze state unnecessarily.
(We already have comments about this in bugzilla)
Link: https://bugzilla.kernel.org/show_bug.cgi?id=84651
Reported-and-tested-by: Ethan Schoonover <es@ethanschoonover.com>
Tested-by: Peter Amidon <psa.pub.0@picnicpark.org>
Tested-by: Yani Ioadnnou <yani.ioannou@gmail.com>
Tested-by: Mister Wardrop <mister.wardrop@gmail.com>
Tested-by: Anton Anikin <anton@anikin.name>
Tested-by: Keith McClelland <zismylaptop@gmail.com>
Reviewed-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Chen Yu <yu.c.chen@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The acpi_suspend() function has no callers, so drop it.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org>
This makes a difference if the compiler decides not to inline the
function, as then the function's reference to acpisleep_dmi_table[]
yields a section mismatch warning.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
After multiple GPEs have been disabled at the low level in one go,
like when acpi_disable_all_gpes() is called, we should always drain
all of the outstanding events from them, or interesting races become
possible.
For this reason, call acpi_os_wait_events_complete() after
acpi_enable_all_wakeup_gpes() and acpi_disable_all_gpes() in
acpi_freeze_prepare() and acpi_power_off_prepare(), respectively.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The ACPI GPE wakeup from suspend-to-idle is currently based on using
the IRQF_NO_SUSPEND flag for the ACPI SCI, but that is problematic
for a couple of reasons. First, in principle the ACPI SCI may be
shared and IRQF_NO_SUSPEND does not really work well with shared
interrupts. Second, it may require the ACPI subsystem to special-case
the handling of device notifications depending on whether or not
they are received during suspend-to-idle in some places which would
lead to fragile code. Finally, it's better the handle ACPI wakeup
interrupts consistently with wakeup interrupts from other sources.
For this reason, remove the IRQF_NO_SUSPEND flag from the ACPI SCI
and use enable_irq_wake()/disable_irq_wake() with it instead, which
requires two additional platform hooks to be added to struct
platform_freeze_ops.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
NVS region is saved and restored unconditionally for machines without
nvs_nosave quirk during S3. Tested some new machines and the operation
is not necessary. Saving NVS region also affects S2RAM speed. The time of
NVS saving and restoring depends on the size of NVS region and it consumes
7~10ms normally.
This patch is to make machines produced from 2012 to now not saving NVS region
to accelerate S3.
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Adds trace events that give finer resolution into suspend/resume. These
events are graphed in the timelines generated by the analyze_suspend.py
script. They represent large areas of time consumed that are typical to
suspend and resume.
The event is triggered by calling the function "trace_suspend_resume"
with three arguments: a string (the name of the event to be displayed
in the timeline), an integer (case specific number, such as the power
state or cpu number), and a boolean (where true is used to denote the start
of the timeline event, and false to denote the end).
The suspend_resume trace event reproduces the data that the machine_suspend
trace event did, so the latter has been removed.
Signed-off-by: Todd Brandt <todd.e.brandt@intel.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The "freeze" sleep state suffers from the same issue that was
addressed by commit ad07277e82 (ACPI / PM: Hold acpi_scan_lock over
system PM transitions) for ACPI sleep states, that is, things break
if ->remove() is called for devices whose system resume callbacks
haven't been executed yet.
It also can be addressed in the same way, by holding the ACPI scan
lock over the "freeze" sleep state and PM transitions to and from
that state, but ->begin() and ->end() platform operations for the
"freeze" sleep state are needed for this purpose.
This change has been tested on Acer Aspire S5 with Thunderbolt.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Export the acpi_target_system_state() function to modules so that
modular drivers can use it to check what the target ACPI sleep state
of the system is (that is needed for i915 mostly at this point).
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
If the HW Reduced ACPI mode bit is set in the FADT, ACPICA uses
the optional sleep control and sleep status registers for making
the system enter sleep states (including S5), so it is not possible
to use system sleep states or power it off using ACPI if the HW
Reduced ACPI mode bit is set and those registers are not available.
For this reason, add a new function, acpi_sleep_state_supported(),
checking if the HW Reduced ACPI mode bit is set and whether or not
system sleep states are usable in that case in addition to checking
the return value of acpi_get_sleep_type_data() and make the ACPI
sleep setup routines use that function to check the availability of
system sleep states.
Among other things, this prevents the kernel from attempting to
use ACPI for powering off HW Reduced ACPI systems without the sleep
control and sleep status registers, because ACPI power off doesn't
have a chance to work on them. That allows alternative power off
mechanisms that may actually work to be used on those systems. The
affected machines include Dell Venue 8 Pro, Asus T100TA, Haswell
Desktop SDP and Ivy Bridge EP Demo depot.
References: https://bugzilla.kernel.org/show_bug.cgi?id=70931
Reported-by: Adam Williamson <awilliam@redhat.com>
Tested-by: Aubrey Li <aubrey.li@linux.intel.com>
Cc: 3.4+ <stable@vger.kernel.org> # 3.4+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Revert commit 3130497f5b ("ACPI / sleep: pm_power_off needs more
sanity checks to be installed") that breaks power ACPI power off on a
lot of systems, because it checks wrong registers.
Fixes: 3130497f5b ("ACPI / sleep: pm_power_off needs more sanity checks to be installed")
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Sleep control and status registers need santity checks as well before
ACPI installs acpi_power_off to pm_power_off hook. The checking code in
acpi_enter_sleep_state() is too late, we should not allow a not-working
pm_power_off function to be hooked up.
Signed-off-by: Aubrey Li <aubrey.li@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* acpi-gpe:
ACPI / EC: disable GPE before removing GPE handler
ACPI / Button: Fix enabling button GPEs twice
* acpi-video:
ACPI: Blacklist Win8 OSI for some HP laptop 2013 models
ACPI / video: Fix typo in video_detect.c
* acpi-thermal:
ACPI / thermal: remove const from thermal_zone_device_ops declaration
* acpi-processor:
ACPI / scan: bail out early if failed to parse APIC ID for CPU
* acpi-sleep:
ACPI / sleep: remove panic in case hardware has changed after S4
* acpi-cleanup: (22 commits)
ACPI / tables: Return proper error codes from acpi_table_parse() and fix comment.
ACPI / tables: Check if id is NULL in acpi_table_parse()
ACPI / proc: Include appropriate header file in proc.c
ACPI / EC: Remove unused functions and add prototype declaration in internal.h
ACPI / dock: Include appropriate header file in dock.c
ACPI / PCI: Include appropriate header file in pci_link.c
ACPI / PCI: Include appropriate header file in pci_slot.c
ACPI / EC: Mark the function acpi_ec_add_debugfs() as static in ec_sys.c
ACPI / NVS: Include appropriate header file in nvs.c
ACPI / OSL: Mark the function acpi_table_checksum() as static
ACPI / processor: initialize a variable to silence compiler warning
ACPI / processor: use ACPI_COMPANION() to get ACPI device
ACPI: correct minor typos
ACPI / sleep: Drop redundant acpi_disabled check
ACPI / dock: Drop redundant acpi_disabled check
ACPI / table: Replace '1' with specific error return values
ACPI: remove trailing whitespace
ACPI / IBFT: Fix incorrect <acpi/acpi.h> inclusion in iSCSI boot firmware module
ACPI / i915: Fix incorrect <acpi/acpi.h> inclusions via <linux/acpi_io.h>
SFI / ACPI: Fix warnings reported during builds with W=1
...
Conflicts:
drivers/acpi/nvs.c
drivers/hwmon/asus_atk0110.c
Some BIOSes change hardware based on the state of
a laptop's lid. If the lid is closed, the touchpad is
disabled and the checksum changes. Windows 8 no longer
aborts resume if the checksum has changed.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
[rjw: Use pr_crit() for the message and don't break the string]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
acpi_sleep_init() is only called from acpi_bus_init() and the
code logic shows that it doesn't need to check acpi_disabled:
acpi_init();
if (acpi_disabled) return;
acpi_bus_init();
acpi_sleep_init();
if (acpi_disabled)
return 0;
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
[rjw: Subject and changelog]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Replace direct inclusions of <acpi/acpi.h>, <acpi/acpi_bus.h> and
<acpi/acpi_drivers.h>, which are incorrect, with <linux/acpi.h>
inclusions and remove some inclusions of those files that aren't
necessary.
First of all, <acpi/acpi.h>, <acpi/acpi_bus.h> and <acpi/acpi_drivers.h>
should not be included directly from any files that are built for
CONFIG_ACPI unset, because that generally leads to build warnings about
undefined symbols in !CONFIG_ACPI builds. For CONFIG_ACPI set,
<linux/acpi.h> includes those files and for CONFIG_ACPI unset it
provides stub ACPI symbols to be used in that case.
Second, there are ordering dependencies between those files that always
have to be met. Namely, it is required that <acpi/acpi_bus.h> be included
prior to <acpi/acpi_drivers.h> so that the acpi_pci_root declarations the
latter depends on are always there. And <acpi/acpi.h> which provides
basic ACPICA type declarations should always be included prior to any other
ACPI headers in CONFIG_ACPI builds. That also is taken care of including
<linux/acpi.h> as appropriate.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com> (drivers/pci stuff)
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> (Xen stuff)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Initialize pwr_btn_status as disabled which (a) makes sure it is
in a proper state to start, and (b) cleans up a compiler warning
about an uninitialized variable.
Signed-off-by: Al Stone <al.stone@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Bad things happen if ACPI hotplug events are handled during system
PM transitions, especially if devices are removed as a result.
To prevent those bad things from happening, acquire acpi_scan_lock
when a PM transition is started and release it when that transition
is complete or has been aborted.
This fixes resume lockup on my test-bed Acer Aspire S5 that happens
when Thunderbolt devices are disconnected from the machine while
suspended.
Also fixes the analogous problem for Mika Westerberg on an
Intel DZ77RE-75K board.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Toshi Kani <toshi.kani@hp.com>
__initdata should be placed between the variable name and equal
sign for the variable to be placed in the intended section.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Introduce helper function acpi_execute_simple_method() and use it in
a number of places to simplify code.
[rjw: Changelog]
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Which by default will be x86_acpi_suspend_lowlevel.
This registration allows us to register another callback
if there is a need to use another platform specific callback.
Signed-off-by: Liang Tang <liang.tang@oracle.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Tested-by: Ben Guthro <benjamin.guthro@citrix.com>
Acked-by: "H. Peter Anvin" <hpa@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add Sony Vaio VGN-FW21M to the device blacklist in
drivers/acpi/sleep.c.
Fixes suspend/resume on this device (device no longer reboots
instead of resuming).
References: https://bugzilla.kernel.org/show_bug.cgi?id=55001
Signed-off-by: Fabio Valentini <fafatheone@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Got this dmesg log on an Acer Aspire 725.
[ 0.256351] ACPI: (supports S0ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S1_] (20130117/hwxface-568)
[ 0.256373] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S2_] (20130117/hwxface-568)
[ 0.256391] S3 S4 S5)
Avoid this interleaving error messages.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch adds a quirk to allow the Sony VGN-FW41E_H to suspend/resume
properly.
References: http://bugs.launchpad.net/bugs/1113547
Signed-off-by: Joseph Salisbury <joseph.salisbury@canonical.com>
Cc: All <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Move some suspend-specific and hibernate-specific code from
acpi_sleep_init() into separate functions to get rid of explicit
#ifdefs in acpi_sleep_init(). Use pr_info() to start and pr_cont()
to continue printing the supported ACPI sleep states line.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The ACPI power resources driver is not very useful, because the only
thing it really does is to restore the state of the power resources
that were "on" before system suspend or hibernation, but that may be
achieved in a different way.
Drop the ACPI power resources driver entirely and add
acpi_resume_power_resources() that will walk the list of all
registered power resources during system resume and turn on the ones
that were "on" before the preceding system suspend or hibernation.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* acpi-general:
ACPI / PNP: Do not crash due to stale pointer use during system resume
ACPI / video: Add "Asus UL30VT" to ACPI video detect blacklist
ACPI: do acpisleep dmi check when CONFIG_ACPI_SLEEP is set
The current acpisleep DMI checks only run when CONFIG_SUSPEND is set.
And this may break hibernation on some platforms when CONFIG_SUSPEND
is cleared.
Move acpisleep DMI check into #ifdef CONFIG_ACPI_SLEEP instead.
[rjw: Added acpi_sleep_dmi_check() and rebased on top of earlier
patches adding entries to acpisleep_dmi_table[].]
References: https://bugzilla.kernel.org/show_bug.cgi?id=45921
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* acpi-general: (38 commits)
ACPI / thermal: _TMP and _CRT/_HOT/_PSV/_ACx dependency fix
ACPI: drop unnecessary local variable from acpi_system_write_wakeup_device()
ACPI: Fix logging when no pci_irq is allocated
ACPI: Update Dock hotplug error messages
ACPI: Update Container hotplug error messages
ACPI: Update Memory hotplug error messages
ACPI: Update CPU hotplug error messages
ACPI: Add acpi_handle_<level>() interfaces
ACPI: remove use of __devexit
ACPI / PM: Add Sony Vaio VPCEB1S1E to nonvs blacklist.
ACPI / battery: Correct battery capacity values on Thinkpads
Revert "ACPI / x86: Add quirk for "CheckPoint P-20-00" to not use bridge _CRS_ info"
ACPI: create _SUN sysfs file
ACPI / memhotplug: bind the memory device when the driver is being loaded
ACPI / memhotplug: don't allow to eject the memory device if it is being used
ACPI / memhotplug: free memory device if acpi_memory_enable_device() failed
ACPI / memhotplug: fix memory leak when memory device is unbound from acpi_memhotplug
ACPI / memhotplug: deal with eject request in hotplug queue
ACPI / memory-hotplug: add memory offline code to acpi_memory_device_remove()
ACPI / memory-hotplug: call acpi_bus_trim() to remove memory device
...
Conflicts:
include/linux/acpi.h (two additions at the end of the same file)
Sony Vaio VPCEB1S1E does not resume correctly without
acpi_sleep=nonvs, so add it to the ACPI sleep blacklist.
References: https://bugzilla.kernel.org/show_bug.cgi?id=48781
Reported-by: Sébastien Wilmet <swilmet@gnome.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The ACPI specificiation would like us to save NVS at hibernation time,
but makes no mention of saving NVS over S3. Not all versions of
Windows do this either, and it is clear that not all machines need NVS
saved/restored over S3. Allow the user to improve their suspend/resume
time by disabling the NVS save/restore at S3 time, but continue to do
the NVS save/restore for S4 as specified.
Signed-off-by: Kristen Carlson Accardi <kristen@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Introduce helper function returning the target sleep state of the
system and use it to move the remaining device power management
functions from sleep.c to device_pm.c.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Two device wakeup management routines in device_pm.c and sleep.c,
acpi_pm_device_run_wake() and acpi_pm_device_sleep_wake(), take a
device pointer argument and use it to obtain the ACPI handle of the
corresponding ACPI namespace node. That handle is then used to get
the address of the struct acpi_device object corresponding to the
struct device passed as the argument.
Unfortunately, that last operation may be costly, because it involves
taking the global ACPI namespace mutex, so it shouldn't be carried
out too often. However, the callers of those routines usually call
them in a row with acpi_pm_device_sleep_state() which also takes that
mutex for the same reason, so it would be more efficient if they ran
acpi_bus_get_device() themselves to obtain a pointer to the struct
acpi_device object in question and then passed that pointer to the
appropriate PM routines.
To make that possible, split each of the PM routines mentioned above
in two parts, one taking a struct acpi_device pointer argument and
the other implementing the current interface for compatibility.
Additionally, change acpi_pm_device_run_wake() to actually return
an error code if there is an error while setting up runtime remote
wakeup for the device.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The ACPI function for setting up devices to do runtime remote
wakeup is now located in drivers/acpi/sleep.c, but
drivers/acpi/device_pm.c is a more logical place for it, so move it
there.
No functional changes should result from this modification.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The ACPI function for choosing device power state is now located
in drivers/acpi/sleep.c, but drivers/acpi/device_pm.c is a more
logical place for it, so move it there.
However, instead of moving the function entirely, move its core only
under a different name and with a different list of arguments, so
that it is more flexible, and leave a wrapper around it in the
original location.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The kerneldoc comments for acpi_pm_device_sleep_state(),
acpi_pm_device_run_wake(), and acpi_pm_device_sleep_wake() are
outdated or otherwise inaccurate and/or don't follow the common
kerneldoc patterns, so fix them.
Additionally, notice that acpi_pm_device_run_wake() should be under
CONFIG_PM_RUNTIME rather than under CONFIG_PM_SLEEP, so fix that too.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Make ACPI power management routines and PCI power management
routines depending on ACPI take device PM QoS flags into account
when deciding what power state to put the device into.
In particular, after this change acpi_pm_device_sleep_state() will
not return ACPI_STATE_D3_COLD as the deepest available low-power
state if PM_QOS_FLAG_NO_POWER_OFF is requested for the device and it
will not require remote wakeup to work for the device in the returned
low-power state if there is at least one PM QoS flags request for the
device, but PM_QOS_FLAG_REMOTE_WAKEUP is not requested for it.
Accordingly, acpi_pci_set_power_state() will refuse to put the
device into D3cold if PM_QOS_FLAG_NO_POWER_OFF is requested for it.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Huang Ying <ying.huang@intel.com>
_GTS and _BFS were added to the suspend/resume flow
in the ACPI 2.0 specification.
Linux dutifully implemented _GTS and _BFS.
We discovered that it was rarely seen in systems
in the field. Further, some of those systems had
AML so bogus that it could never work -- proof that
no other operating system supports _GTS and _BFS.
So we made _GTS and _BFS optional via modparam,
and disabled them by default.
But we've had to complicate some code to keep
this support in the kernel, as these methods are defined
to be evaluated very close to sleep entry and exit.
Indeed, no other AML is ever evaluated with interrupts off.
We have submitted a proposal for _GTS and _BFS
to be officially removed from the ACPI specification
on the next revision. Here we remove it from Linux.
Signed-off-by: Len Brown <len.brown@intel.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
If CONFIG_ACPI_SLEEP is unset, the compiler complains that
pwr_btn_event_pending is defined but not used. To silence the
warning, move the definition of pwr_btn_event_pending under an
appropriate #ifdef.
Reported-by: Paul E. McKenney <paul.mckenney@linaro.org>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Tested-by: Paul E. McKenney <paul.mckenney@linaro.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Pull ACPI & power management update from Len Brown:
"Re-write of the turbostat tool.
lower overhead was necessary for measuring very large system when
they are very idle.
IVB support in intel_idle
It's what I run on my IVB, others should be able to also:-)
ACPICA core update
We have found some bugs due to divergence between Linux and the
upstream ACPICA base. Most of these patches are to reduce that
divergence to reduce the risk of future bugs.
Some cpuidle updates, mostly for non-Intel
More will be coming, as they depend on this part.
Some thermal management changes needed by non-ACPI systems.
Some _OST (OS Status Indication) updates for hot ACPI hot-plug."
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux: (51 commits)
Thermal: Documentation update
Thermal: Add Hysteresis attributes
Thermal: Make Thermal trip points writeable
ACPI/AC: prevent OOPS on some boxes due to missing check power_supply_register() return value check
tools/power: turbostat: fix large c1% issue
tools/power: turbostat v2 - re-write for efficiency
ACPICA: Update to version 20120711
ACPICA: AcpiSrc: Fix some translation issues for Linux conversion
ACPICA: Update header files copyrights to 2012
ACPICA: Add new ACPI table load/unload external interfaces
ACPICA: Split file: tbxface.c -> tbxfload.c
ACPICA: Add PCC address space to space ID decode function
ACPICA: Fix some comment fields
ACPICA: Table manager: deploy new firmware error/warning interfaces
ACPICA: Add new interfaces for BIOS(firmware) errors and warnings
ACPICA: Split exception code utilities to a new file, utexcep.c
ACPI: acpi_pad: tune round_robin_time
ACPICA: Update to version 20120620
ACPICA: Add support for implicit notify on multiple devices
ACPICA: Update comments; no functional change
...
Two bits were appended to the end of the bitfield
list in struct scsi_device. Resolve that conflict
by including both bits.
Conflicts:
include/scsi/scsi_device.h
ATA port may support runtime D3Cold state, for example, Zero-power ODD case.
This patch adds wakeup notifier and enable/disable run_wake during
supend/resume.
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Lower device sleep state can save more power, but has more exit
latency too. Sometimes, to satisfy some power QoS and other
requirement, we need to constrain the lowest device sleep state.
In this patch, a parameter to specify lowest allowed state for
acpi_pm_device_sleep_state is added. So that the caller can enforce
the constraint via the parameter.
This is needed by PCIe D3cold support, where the lowest power state
allowed may be D3_HOT instead of default D3_COLD.
CC: Len Brown <lenb@kernel.org>
CC: linux-acpi@vger.kernel.org
Reviewed-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Pull some left-over PM patches from Rafael J. Wysocki.
* 'pm-acpi' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / PM: Make acpi_pm_device_sleep_state() follow the specification
ACPI / PM: Make __acpi_bus_get_power() cover D3cold correctly
ACPI / PM: Fix error messages in drivers/acpi/bus.c
rtc-cmos / PM: report wakeup event on ACPI RTC alarm
ACPI / PM: Generate wakeup events on fixed power button
Remove the unused argument of acpi_os_wait_events_complete.
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Revert usage of acpi_wakeup_address and move definition
to x86 architecture code in order to make compilation work
in ia64.
[jsakkine: tested compilation in ia64/x86-64 and added
proper commit message]
Reported-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Originally-by: H. Peter Anvin <hpa@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@intel.com>
Link: http://lkml.kernel.org/r/1338370421-27735-1-git-send-email-jarkko.sakkinen@intel.com
Cc: Tony Luck <tony.luck@intel.com>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Pull x86 trampoline rework from H. Peter Anvin:
"This code reworks all the "trampoline"/"realmode" code (various bits
that need to live in the first megabyte of memory, most but not all of
which runs in real mode at some point) in the kernel into a single
object. The main reason for doing this is that it eliminates the last
place in the kernel where we needed pages to be mapped RWX. This code
separates all that code into proper R/RW/RX pages."
Fix up conflicts in arch/x86/kernel/Makefile (mca removed next to reboot
code), and arch/x86/kernel/reboot.c (reboot code moved around in one
branch, modified in this one), and arch/x86/tools/relocs.c (mostly same
code came in earlier due to working around the ld bugs just before the
3.4 release).
Also remove stale x86-relocs entry from scripts/.gitignore as per Peter
Anvin.
* commit '61f5446169046c217a5479517edac3a890c3bee7': (36 commits)
x86, realmode: Move end signature into header.S
x86, relocs: When printing an error, say relative or absolute
x86, relocs: More relocations which may end up as absolute
x86, relocs: Workaround for binutils 2.22.52.0.1 section bug
xen-acpi-processor: Add missing #include <xen/xen.h>
acpi, bgrd: Add missing <linux/io.h> to drivers/acpi/bgrt.c
x86, realmode: Change EFER to a single u64 field
x86, realmode: Move kernel/realmode.c to realmode/init.c
x86, realmode: Move not-common bits out of trampoline_common.S
x86, realmode: Mask out EFER.LMA when saving trampoline EFER
x86, realmode: Fix no cache bits test in reboot_32.S
x86, realmode: Make sure all generated files are listed in targets
x86, realmode: build fix: remove duplicate build
x86, realmode: read cr4 and EFER from kernel for 64-bit trampoline
x86, realmode: fixes compilation issue in tboot.c
x86, realmode: move relocs from scripts/ to arch/x86/tools
x86, realmode: header for trampoline code
x86, realmode: flattened rm hierachy
x86, realmode: don't copy real_mode_header
x86, realmode: fix 64-bit wakeup sequence
...
The comparison between the system sleep state being entered
and the lowest system sleep state the given device may wake up
from in acpi_pm_device_sleep_state() is reversed, because the
specification (ACPI 5.0) says that for wakeup to work:
"The sleeping state being entered must be less than or equal to the
power state declared in element 1 of the _PRW object."
In other words, the state returned by _PRW is the deepest
(lowest-power) system sleep state the device is capable of waking up
the system from.
Moreover, acpi_pm_device_sleep_state() also should check if the
wakeup capability is supported through ACPI, because in principle it
may be done via native PCIe PME, for example, in which case _SxW
should not be evaluated.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
When the system is woken up by the ACPI fixed power button, currently there
is no way of userspace becoming aware that the power button was pressed.
OLPC would like to know this, so that we can respond appropriately.
For example, if the system was woken up by a network packet, we know
we can go back to sleep very quickly. But if the user explicitly woke the
system with the power button, we're going to want to stay awake for a
while.
The wakeup count mechanism seems like a good fit for communicating this.
Mark the fixed power button as wakeup-enabled, and increment its wakeup
counter when the system is woken with the power button. (The wakeup counter
is also incremented when the power button is pressed during system
operation; this is already handled by an existing acpi-button codepath).
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Migrated ACPI wakeup code to the real-mode blob.
Code existing in .x86_trampoline can be completely
removed. Static descriptor table in wakeup_asm.S is
courtesy of H. Peter Anvin.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@intel.com>
Link: http://lkml.kernel.org/r/1336501366-28617-7-git-send-email-jarkko.sakkinen@intel.com
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Len Brown <len.brown@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
With commit a2ef5c4fd4
"ACPI: Move module parameter gts and bfs to sleep.c" the wake_sleep_flags
is required when calling acpi_enter_sleep_state, which means
that if there are functions outside the sleep.c code they
can't get the wake_sleep_flags values.
This converts the function in to a exported value and converts
the module config operands to a function.
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Lin Ming <ming.m.lin@intel.com>
[v2: Parameters can be turned on/off dynamically]
[v3: unsigned char -> u8]
[v4: val -> kp->arg]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Link: http://lkml.kernel.org/r/1335150198-21899-2-git-send-email-konrad.wilk@oracle.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Conflicts:
drivers/acpi/sleep.c
This was a text conflict between
a2ef5c4fd4
(ACPI: Move module parameter gts and bfs to sleep.c)
which added #include <linux/module.h>
and
b24e509885
(ACPI, PCI: Move acpi_dev_run_wake() to ACPI core)
which added #include <linux/pm_runtime.h>
The resolution was to take them both.
Signed-off-by: Len Brown <len.brown@intel.com>
acpi_dev_run_wake() is a generic function which can be used by
other subsystem too. Rename it to acpi_pm_device_run_wake, to be
consistent with acpi_pm_device_sleep_wake.
Then move it to ACPI core.
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Move linux specific module parameter gts and bfs out of ACPICA core
code to sleep.c.
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Enhanced the sleep/wake interfaces to optionally execute the
_GTS method (Going To Sleep), and the _BFS method (Back From
Sleep). Windows apparently does not execute these methods, and
therefore these methods are often untested. It has been seen on
some systems where the execution of these methods causes errors
and also prevents the machine from entering S5. It is therefore
suggested that host operating systems do not execute these methods
by default. In the future, perhaps these methods can be optionally
executed based on the age of the system and/or what is the newest
version of Windows that the BIOS asks for via _OSI.
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Changed the METHOD_NAME* defines that define a full pathname to
the method to METHOD_PATHNAME* in order to make it clear that
it is not a simple 4-character ACPI name. Used for the various
sleep/wake methods.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Sony Vaio VPCCW29FX does not resume correctly without
acpi_sleep=nonvs, so add it to the ACPI sleep blacklist.
https://bugzilla.kernel.org/show_bug.cgi?id=34722
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The models do not resume correctly without acpi_sleep=nonvs.
Signed-off-by: Keng-Yu Lin <kengyu@canonical.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Srinivas Pandruvada
Rafael J. Wysocki
Jean Delvare
Linus Torvalds
Hans de Goede
Zhang Rui
Lv Zheng
Ocean He
Chen Yu
Lukas Wunner
Sudeep Holla
Jan Beulich
Lan Tianyu
Todd E Brandt
Li, Aubrey
Oliver Neukum
Hanjun Guo
Al Stone
Sachin Kamat
Jiang Liu
Konrad Rzeszutek Wilk
Fabio Valentini
Joe Perches
Joseph Salisbury
Kristen Carlson Accardi
Len Brown
Rafael J. Wysocki
Jeff Garzik
Lin Ming
Huang Ying
H. Peter Anvin
Daniel Drake
Jarkko Sakkinen
Kay Sievers
Bob Moore
Keng-Yu Lin
Dave Jones