Most of the subdevices for the WM8350 code are registered in the same
fashion so factor out the code to do the initial registration.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Samuel Ortiz <sameo@openedhand.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The WM8350 features six DCDC convertors (four buck and two boost), four
LDO voltage regulators and two constant current sinks. This driver adds
support for these through the regulator API.
This driver was written by Liam Girdwood with updates for submission
from Mark Brown.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The WM8350 has an interrupt line to the CPU which is shared by the
devices on the CPU. This patch adds support for the interrupt
controller within the WM8350 which identifies which identifies the
interrupt cause. In common with other similar chips this is done
outside the standard interrupt framework due to the need to access
the interrupt controller over an interrupt-driven bus.
This code was all originally written by Liam Girdwood with updates for
submission by me.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Samuel Ortiz <sameo@openedhand.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Some functions of the WM8350 require board-specific initialisation on
startup. Provide a callback to the WM8350 driver in platform data
for platforms to use to configure the chip. Use of a callback allows
platforms to control the ordering of initialisation which can be
important.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Samuel Ortiz <sameo@openedhand.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The WM8350 provides a number of user-configurable pins providing access
to various signals generated by the functions on the chip. These are
referred to as GPIO pins in the device documentation but in Linux terms
they are more general than that, providing configuration of alternate
functions.
This patch implements support for selecting the alternate functions for
these pins. They can also be used as GPIOs in the normal Linux sense -
a subsequent patch will add support for doing so.
This code was all written by Liam Girdwood and has had minor updates
and rearrangements by Mark Brown.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Samuel Ortiz <sameo@openedhand.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Implement the I2C control interface for the WM8350. This code was
originally written by Liam Girdwood and has been updated for submission
by Mark Brown.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Samuel Ortiz <sameo@openedhand.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The WM8350 is an integrated audio and power management subsystem
intended for use as the primary PMIC in mobile multimedia applications.
The WM8350 can be controlled via either I2C or SPI - the control
interface is provided by a separate module in order to allow greatest
flexibility in configuring the kernel.
This driver was originally written by Liam Girdwood and has since been
updated to current kernel APIs and split up for submission by me. All
the heavy lifting here was done by Liam.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Samuel Ortiz <sameo@openedhand.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Samuel Ortiz <sameo@openedhand.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Samuel Ortiz <sameo@openedhand.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Samuel Ortiz <sameo@openedhand.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Samuel Ortiz <sameo@openedhand.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Samuel Ortiz <sameo@openedhand.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Samuel Ortiz <sameo@openedhand.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Samuel Ortiz <sameo@openedhand.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Provide a new file 'name' in the regulator sysfs class with a human
readable name for the regulator for use in applications.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The WM8400 provides two programmable DCDC step-down (buck) convertors
and four low-dropout (LDO) regulators. This driver provides support for
runtime managment of these in the standard regulator API.
Support for configuration of the suspend and hibernate mode behaviour
of the regulators is not yet included.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The WM8400 is a highly integrated audio CODEC and power management unit
optimised for use in mobile multimedia applications. This patch adds
core support for the WM8400 to the MFD subsystem.
Both I2C and SPI access are supported by the hardware but currently only
I2C access is implemented. The code is structured to allow SPI support
to be slotted in later.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Samuel Ortiz <sameo@openedhand.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
If the machine constraints mark a regulator as always_on but this was
not done by the bootloader then enable the regulator when applying
constraints.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Try to find a human readable name for the regulator we're failing on and
print a specific diagnostic when we fail to set the suspend state.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Since it is now mandatory to supply constraints via init_data on device
registration check for that when registering, saving us from oopsing
later on.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This improves the machine level API in order to configure
regulator constraints and consumers as platform data and removes the
old string based API that required several calls to set up each regulator.
The intention is to create a struct regulator_init_data, populate
it's fields with constraints, consumers devices, etc and then register
the regulator device from board.c in the standard Linux way.
e.g. regulator LDO2 (supplying codec and sim) platform data.
/* regulator LDO2 consumer devices */
static struct regulator_consumer_supply ldo2_consumers[] = {
{
.dev = &platform_audio_device.dev,
.supply = "codec_avdd",
},
{
.dev = &platform_sim_device.dev,
.supply = "sim_vcc",
}
};
/* regulator LDO2 constraints */
static struct regulator_init_data ldo2_data = {
.constraints = {
.min_uV = 3300000,
.max_uV = 3300000,
.valid_modes_mask = REGULATOR_MODE_NORMAL,
.apply_uV = 1,
},
.num_consumer_supplies = ARRAY_SIZE(ldo2_consumers),
.consumer_supplies = ldo2_consumers,
};
/* machine regulator devices with thier consumers and constraints */
static struct platform_device wm8350_regulator_devices[] = {
{
.name = "wm8350-regulator",
.id = WM8350_LDO_2,
.dev = {
.platform_data = &ldo2_data,
},
},
};
Changes in detail:-
o Removed all const char* regulator config functions in machine API.
o Created new struct regulator_init_data to contain regulator
machine configuration constraints and consmuers.
o Changed set_supply(), set_machine_constraints(),
set_consumer_device_supply() to remove their string identifier
parameters. Also made them static and moved functions nearer top of
core.c.
o Removed no longer used inline func to_rdev()
o Added regulator_get_init_drvdata() to retrieve init data.
o Added struct device* as parameter to regulator_register().
o Changed my email address.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This is a much better version of a previous patch to make the parser
tables constant. Rather than changing the typedef, we put the "const" in
all the various places where its required, allowing the __initconst
exception for nfsroot which was the cause of the previous trouble.
This was posted for review some time ago and I believe its been in -mm
since then.
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
Cc: Alexander Viro <aviro@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/blackfin-2.6: (60 commits)
Blackfin arch: make sure we include the fix for SPORT hysteresis when reprogramming clocks
Blackfin arch: Fix bogus str_ident check in gpio code
Blackfin arch: AD7879 Touchscreen driver
Blackfin arch: introducing bfin_addr_dcachable
Blackfin arch: fix a typo in comments
Blackfin arch: Remove useless head file
Blackfin arch: make sure L2 start and length are always defined (fixes building on BF542)
Blackfin arch: use the Blackfin on-chip ROM to do software reset when possible
Blackfin arch: update anomaly headers to match the latest sheet
Blackfin arch: bfin_reset() is an internal reboot function ... everyone should go through machine_restart()
Blackfin arch: print out error/warning if you are running on the incorrect CPU type
Blackfin arch: remove non-bf54x ifdef logic since this file is only compiled on bf54x parts
Blackfin arch: update board defconfigs
Blackfin arch: Add optional verbose debug
Blackfin arch: emulate a TTY over the EMUDAT/JTAG interface
Blackfin arch: have is_user_addr_valid() check for overflows (like when address is -1)
Blackfin arch: ptrace - fix off-by-one check on end of memory regions
Blackfin arch: Enable framebuffer support for the BF526-EZkit TFT LCD display
Blackfin arch: flash memory map and dm9000 resources updating
Blackfin arch: early prink code still use uart core console functions to parse and set configure option string
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6: (33 commits)
ALSA: ASoC codec: remove unused #include <version.h>
ALSA: ASoC: update email address for Liam Girdwood
ALSA: hda: corrected invalid mixer values
ALSA: hda: add mixers for analog mixer on 92hd75xx codecs
ALSA: ASoC: Add destination and source port for DMA on OMAP1
ALSA: ASoC: Drop device registration from GTA01 lm4857 driver
ALSA: ASoC: Fix build of GTA01 audio driver
ALSA: ASoC: Add widgets before setting endpoints on GTA01
ALSA: ASoC: Fix inverted input PGA mute bits in WM8903
ALSA: ASoC: OMAP: Set DMA stream name at runtime in McBSP DAI driver
ALSA: ASoC: OMAP: Add support for OMAP2430 and OMAP34xx in McBSP DAI driver
ALSA: ASoC: OMAP: Add multilink support to McBSP DAI driver
ALSA: ASoC: Make TLV320AIC26 user-visible
ALSA: ASoC - clean up Kconfig for TLV320AIC2
ALSA: ASoC: Make WM8510 microphone input a DAPM mixer
ALSA: ASoC: Implement WM8510 bias level control
ALSA: ASoC: Remove unused AUDIO_NAME define from codec drivers
ALSA: ASoC: tlv320aic3x: Use uniform tlv320aic naming
ALSA: ASoC: Add WM8510 SPI support
ALSA: ASoC: Add WM8753 SPI support
...
* 'proc' of git://git.kernel.org/pub/scm/linux/kernel/git/adobriyan/proc:
proc: remove kernel.maps_protect
proc: remove now unneeded ADDBUF macro
[PATCH] proc: show personality via /proc/pid/personality
[PATCH] signal, procfs: some lock_task_sighand() users do not need rcu_read_lock()
proc: move PROC_PAGE_MONITOR to fs/proc/Kconfig
proc: make grab_header() static
proc: remove unused get_dma_list()
proc: remove dummy vmcore_open()
proc: proc_sys_root tweak
proc: fix return value of proc_reg_open() in "too late" case
Fixed up trivial conflict in removed file arch/sparc/include/asm/dma_32.h
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6: (24 commits)
integrity: special fs magic
As pointed out by Jonathan Corbet, the timer must be deleted before
ERROR: code indent should use tabs where possible
The tpm_dev_release function is only called for platform devices, not pnp
Protect tpm_chip_list when transversing it.
Renames num_open to is_open, as only one process can open the file at a time.
Remove the BKL calls from the TPM driver, which were added in the overall
netlabel: Add configuration support for local labeling
cipso: Add support for native local labeling and fixup mapping names
netlabel: Changes to the NetLabel security attributes to allow LSMs to pass full contexts
selinux: Cache NetLabel secattrs in the socket's security struct
selinux: Set socket NetLabel based on connection endpoint
netlabel: Add functionality to set the security attributes of a packet
netlabel: Add network address selectors to the NetLabel/LSM domain mapping
netlabel: Add a generic way to create ordered linked lists of network addrs
netlabel: Replace protocol/NetLabel linking with refrerence counts
smack: Fix missing calls to netlbl_skbuff_err()
selinux: Fix missing calls to netlbl_skbuff_err()
selinux: Fix a problem in security_netlbl_sid_to_secattr()
selinux: Better local/forward check in selinux_ip_postroute()
...
* git://git.infradead.org/users/dwmw2/random-2.6:
Fix autoloading of MacBook Pro backlight driver.
Automatic MODULE_ALIAS() for DMI match tables.
Remove asm/a.out.h files for all architectures without a.out support.
Introduce HAVE_AOUT symbol to remove hard-coded arch list for BINFMT_AOUT
Remove redundant CONFIG_ARCH_SUPPORTS_AOUT
S390: Update comments about why we don't use <asm-generic/statfs.h>
SPARC: Use <asm-generic/statfs.h>
PowerPC: Use <asm-generic/statfs.h>
PARISC: Use <asm-generic/statfs.h>
x86_64: Use <asm-generic/statfs.h>
IA64: Use <asm-generic/statfs.h>
ARM: Use <asm-generic/statfs.h>
Make <asm-generic/statfs.h> suitable for 64-bit platforms.
Define and use PCI_DEVICE_ID_MARVELL_88ALP01_CCIC for CAFÉ camera driver
[MTD] [NAND] Define and use PCI_DEVICE_ID_MARVELL_88ALP01_NAND for CAFÉ
Use PCI_DEVICE_ID_88ALP01 for CAFÉ chip, rather than PCI_DEVICE_ID_CAFE.
EFS: Don't set f_fsid in statfs().
Merges oprofile, timers/hpet, x86/traps, x86/time, and x86/core misc items.
* 'x86-core-v4-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (132 commits)
x86: change early_ioremap to use slots instead of nesting
x86: adjust dependencies for CONFIG_X86_CMOV
dumpstack: x86: various small unification steps, fix
x86: remove additional_cpus
x86: remove additional_cpus configurability
x86: improve UP kernel when CPU-hotplug and SMP is enabled
dumpstack: x86: various small unification steps
dumpstack: i386: make kstack= an early boot-param and add oops=panic
dumpstack: x86: use log_lvl and unify trace formatting
dumptrace: x86: consistently include loglevel, print stack switch
dumpstack: x86: add "end" parameter to valid_stack_ptr and print_context_stack
dumpstack: x86: make printk_address equal
dumpstack: x86: move die_nmi to dumpstack_32.c
traps: x86: finalize unification of traps.c
traps: x86: make traps_32.c and traps_64.c equal
traps: x86: various noop-changes preparing for unification of traps_xx.c
traps: x86_64: use task_pid_nr(tsk) instead of tsk->pid in do_general_protection
traps: i386: expand clear_mem_error and remove from mach_traps.h
traps: x86_64: make io_check_error equal to the one on i386
traps: i386: use preempt_conditional_sti/cli in do_int3
...
Original idea for this from a patch by Rodolfo Giometti which merges various
bits of PPS support
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Drop the kernel lock further and also correct cases where we set rc to an
error code, and then return 0
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
get_current_tty now does internal locking and returns a referenced object,
thus our use of tty_mutex here can go away.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
drivers/char/tty_io.c:1413:17: warning: symbol 'buf' shadows an earlier one
drivers/char/tty_io.c:1379:20: originally declared here
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The multiple drivers share the minor space occupied by a particular major
number, the actual index within the device name's space is indicated by
the tty_driver->name_base + uart_port->line
Another usable formula is (uart_driver->minor - MINOR_BASE) + port->line
Use those to print the device names properly in such situations in
serial_core.c and 8250.c
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Closes bug #11408 by checking the card index range for command 0
Fixes the ioctl to return ENOTTY which is correct for unknown ioctls
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Many tty drivers contain 'can't happen' checks against NULL pointers passed
in by the tty layer. These have never been possible to occur. Even more
importantly if they ever do occur we want to know as it would be a serious
bug.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Stephen's fixes reminded me that gigaset is still rather broken so fix it up
a bit
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Today's linux-next build (x86_64 allmodconfig) failed like this:
/drivers/char/tty_ioctl.c: In function 'change_termios':
drivers/isdn/capi/capi.c🔢 error: implicit declaration of function 'n_tty_ioctl'
drivers/isdn/gigaset/ser-gigaset.c: In function 'gigaset_tty_ioctl':
drivers/isdn/gigaset/ser-gigaset.c:648: error: implicit declaration of function 'n_tty_ioctl'
Introduced by commit 686b5e4aea05a80e370dc931b7f4a8d03c80da54
("tty-move-canon-specials"). I added the following patch (which may not
be correct).
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move the set up on ldisc change into the ldisc
Move the INQ/OUTQ cases into the driver not in shared ioctl code where it
gives bogus answers for other ldisc values
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Copy the simplification from the pty unix98 special case to the generic one.
This allows us to kill off driver->termios_locked entirely which is nice. We
have to whack bits of the cris driver as it meddles in places it shouldn't
providing its own arrays that were never used anyway.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We need both termios and termios_locked so allocate them as one
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The updating and moving around of the pty code added a bug where both the
helper and caller free the main tty struct (the pty driver must free the
o_tty pair itself however).
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We've done the heavy lifting now its time to mop up a bit
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When creating a new pty, save the pty's inode in the tty->driver_data.
Use this inode in pty_kill() to identify the devpts instance. Since
we now have the inode for the pty, we can skip get_node() lookup and
remove the unused get_node().
TODO:
- check if the mutex_lock is needed in pty_kill().
Signed-off-by: Sukadev Bhattiprolu <sukadev@us.ibm.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
devpts_pty_new() is called when setting up a new pty and would not
will not have an existing dentry or inode for the pty. So don't bother
looking for an existing dentry - just create a new one.
Signed-off-by: Sukadev Bhattiprolu <sukadev@us.ibm.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As pointed out by H. Peter Anvin, since the inode for the pty is known,
we don't need to look it up.
Signed-off-by: Sukadev Bhattiprolu <sukadev@us.ibm.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mark Brown
Liam Girdwood
Steven Whitehouse
Linus Torvalds
Alan Cox
Jason Wessel
David S. Miller
Stephen Rothwell
Sukadev Bhattiprolu