Adding QMP v3 USB3 PHY support for SC7180.
Adding only usb phy reset in the list to avoid
reset of DP block.
Signed-off-by: Sandeep Maheswaram <sanm@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/1589510358-3865-5-git-send-email-sanm@codeaurora.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Updated values of USB3 related Sierra PHY registers.
This change fixes USB3 device disconnect issue observed
while enternig U1/U2 state.
Signed-off-by: Sanket Parmar <sparmar@cadence.com>
Link: https://lore.kernel.org/r/1589804053-14302-1-git-send-email-sparmar@cadence.com
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The max_register property must be set in order to
show up the registers in debugfs.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Link: https://lore.kernel.org/r/20200513131254.10497-2-rogerq@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
During different reboot cycles, USB PHY PLL may not always lock
during initialization and therefore can cause USB to be not usable.
Hence do not use internal FSM programming sequence for the USB
PHY initialization.
Fixes: 4dcddbb38b ("phy: sr-usb: Add Stingray USB PHY driver")
Signed-off-by: Bharat Gooty <bharat.gooty@broadcom.com>
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Link: https://lore.kernel.org/r/20200513173947.10919-1-rayagonda.kokatanur@broadcom.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
It's possible that struct qmp_phy_cfg->regs references an array that is
smaller than the possible register lookups that is going to be
performed, with the resulting out-of-bounds read resulting in undefined
behavior.
One such example is when during qcom_qmp_phy_com_init() performs a
qphy_setbits() on entry QPHY_PCS_POWER_DOWN_CONTROL (i.e. 17) with
msm8996_ufsphy_regs_layout only being 12 entries long.
Solve this by inflating all "regs_layout" arrays to ensure that any
remaining entries are zero-initialized, as expected by the code.
Fixes: e4d8b05ad5 ("phy: qcom-qmp: Use proper PWRDOWN offset for sm8150 USB")
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20200515013643.2081941-1-bjorn.andersson@linaro.org
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Move private definitions from header to phy-omap-usb2.c file.
Get rid of unused data structures usb_dpll_params and omap_usb_phy_type.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Link: https://lore.kernel.org/r/20200515080518.26870-2-rogerq@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
phy_ops are never modified and can therefore be made const to allow the
compiler to put it in read-only memory.
Before:
text data bss dec hex filename
7831 3144 128 11103 2b5f drivers/phy/broadcom/phy-bcm-ns2-usbdrd.o
After:
text data bss dec hex filename
7959 3016 128 11103 2b5f drivers/phy/broadcom/phy-bcm-ns2-usbdrd.o
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Link: https://lore.kernel.org/r/20200516120441.7627-2-rikard.falkeborn@gmail.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
A number of structs were not modified and can therefore be made const
to allow the compiler to put them in read-only memory.
In order to do so, update a few functions that don't modify there input
to take pointers to const.
Before:
text data bss dec hex filename
15511 6448 64 22023 5607 drivers/phy/broadcom/phy-brcm-usb.o
After:
text data bss dec hex filename
16058 5936 64 22058 562a drivers/phy/broadcom/phy-brcm-usb.o
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Link: https://lore.kernel.org/r/20200516120441.7627-4-rikard.falkeborn@gmail.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
phy_ops are never modified and can therefore be made const to allow the
compiler to put it in read-only memory.
Before:
text data bss dec hex filename
4310 1244 0 5554 15b2 drivers/phy/broadcom/phy-bcm-sr-usb.o
After:
text data bss dec hex filename
4438 1116 0 5554 15b2 drivers/phy/broadcom/phy-bcm-sr-usb.o
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Link: https://lore.kernel.org/r/20200516120441.7627-3-rikard.falkeborn@gmail.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The .init is used for one-time PHY's initialization, and .power_on
is called many times during the device lifecycle.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Link: https://lore.kernel.org/r/20200513125605.5545-1-peter.chen@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The 3.10 vendor kernel sets the ACA_ENABLE bit on Meson8b, Meson8m2 and
GXBB, but not on Meson8. Add a compatible string for Meson8m2 which also
sets that bit.
While here, also update the Kconfig text and MODULE_DESCRIPTION.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Thomas Graichen <thomas.graichen@gmail.com>
Link: https://lore.kernel.org/r/20200512222424.549351-7-martin.blumenstingl@googlemail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The vendor driver unsets the set_iddig bit during power-on as well and
sets it when suspending the PHY. I did not notice this in the vendor
driver first, because it's part of the dwc_otg driver there (instead of
their PHY code). While here, also add all other REG_DBG_UART register
bit definitions.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Thomas Graichen <thomas.graichen@gmail.com>
Link: https://lore.kernel.org/r/20200512222424.549351-6-martin.blumenstingl@googlemail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Skip setting REG_ADP_BC_ACA_ENABLE on Meson8 SoCs and polling for the
REG_ADP_BC_ACA_PIN_FLOAT bit. The vendor also skips this part on Meson8
SoCs.
This fixes initialization of the host-only USB PHY on Meson8 which would
otherwise fail with "USB ID detect failed!".
Fixes: 4a3449d1a0 ("phy: meson8b-usb2: add support for the USB PHY on Meson8 SoCs")
Reported-by: Thomas Graichen <thomas.graichen@gmail.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Thomas Graichen <thomas.graichen@gmail.com>
Link: https://lore.kernel.org/r/20200512222424.549351-5-martin.blumenstingl@googlemail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Using a MMIO regmap and switch to regmap_update_bits() to simplify the
code in the driver. Also switch to devm_platform_ioremap_resource()
instead of open-coding it. No functional changes intended.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Thomas Graichen <thomas.graichen@gmail.com>
Link: https://lore.kernel.org/r/20200512222424.549351-4-martin.blumenstingl@googlemail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The Intel eMMC PHY is only present on Intel Lightning Mountain SoCs.
Add an architecture dependency to the PHY_INTEL_EMMC config symbol, to
avoid asking the user about it when configuring a kernel for a non-x86
architecture.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200507113626.24026-3-geert+renesas@glider.be
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Fix to return negative error code from some error handling
cases instead of 0, as done elsewhere in this function.
Fixes: 091876cc35 ("phy: ti: j721e-wiz: Add support for WIZ module present in TI J721E SoC")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Link: https://lore.kernel.org/r/20200507054109.110849-1-weiyongjun1@huawei.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The USB phy takes some time to reset, so make sure we give it to it. The
delay length was taken from the 4x12 phy driver.
This manifested in issues with the DWC2 driver since commit fe369e1826
("usb: dwc2: Make dwc2_readl/writel functions endianness-agnostic.")
where the endianness check would read the DWC ID as 0 due to the phy still
resetting, resulting in the wrong endian mode being chosen.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Link: https://lore.kernel.org/r/BN6PR04MB06605D52502816E500683553A3D10@BN6PR04MB0660.namprd04.prod.outlook.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Cadence SALVO PHY is a 28nm product, and is only used for USB3 & USB2.
According to the Cadence, this PHY is a legacy Module, and Sierra and
Torrent are later evolutions from it, and their sequence overlap is
minimal, meaning we cannot reuse either (Sierra & Torrent) of the PHY
drivers.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The UFS QMP v4 PHY has a largely different register set versus USB and
PCIe. Rename the register offsets to denote that the value is specific for
the UFS PCS register.
Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
Link: https://lore.kernel.org/r/1588636467-23409-6-git-send-email-wcheng@codeaurora.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The register map for SM8150 QMP USB SSPHY has moved
QPHY_POWER_DOWN_CONTROL to a different offset. Allow for
an offset in the register table to override default value
if it is a DP capable PHY.
Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
Reviewed-by: Manu Gautam <mgautam@codeaurora.org>
Link: https://lore.kernel.org/r/1588636467-23409-5-git-send-email-wcheng@codeaurora.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add support for SM8150 QMP USB3 PHY with the necessary
initialization sequences as well as additional QMP V4
register definitions.
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
Reviewed-by: Manu Gautam <mgautam@codeaurora.org>
Link: https://lore.kernel.org/r/1588636467-23409-4-git-send-email-wcheng@codeaurora.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This adds the SNPS FemtoPHY V2 driver used in QCOM SOCs. There
are potentially multiple instances of this UTMI PHY on the
SOC, all which can utilize this driver. The V2 driver will
have a different register map compared to V1.
Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
Reviewed-by: Philipp Zabel <pza@pengutronix.de>
Reviewed-by: Manu Gautam <mgautam@codeaurora.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/1588636467-23409-3-git-send-email-wcheng@codeaurora.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add a driver to setup the USB PHY-s on Qualcom m IPQ40xx series SoCs.
The driver sets up HS and SS phys.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Link: https://lore.kernel.org/r/20200503201823.531757-1-robert.marko@sartura.hr
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The AHB clock must be on for qcom_snps_hsphy_init() to be able to write
the initialization sequence to the hardware, so move the clock
enablement to phy init and exit.
Fixes: 67b27dbeac ("phy: qualcomm: Add Synopsys 28nm Hi-Speed USB PHY driver")
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The SM8250 UFS PHY can run off the same initialization sequence as
SM8150, but add the compatible to allow future changes.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This patch fixes a regression in 5.7-rc1+
In commit 8fe75cd4cd ("phy: qcom-qusb2: Add generic QUSB2 V2
PHY support"), the change was made to add "qcom,qusb2-v2-phy"
as a generic compat string. However the change also removed
the "qcom,sdm845-qusb2-phy" compat string, which is documented
in the binding and already in use.
This patch re-adds the "qcom,sdm845-qusb2-phy" compat string
which allows the driver to continue to work with existing dts
entries such as found on the db845c.
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Doug Anderson <dianders@chromium.org>
Cc: Manu Gautam <mgautam@codeaurora.org>
Cc: Sandeep Maheswaram <sanm@codeaurora.org>
Cc: Matthias Kaehlcke <mka@chromium.org>
Cc: Stephen Boyd <swboyd@chromium.org>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: linux-arm-msm@vger.kernel.org
Cc: devicetree@vger.kernel.org
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Fixes: 8fe75cd4cd ("phy: qcom-qusb2: Add generic QUSB2 V2 PHY support")
Reported-by: YongQin Liu <yongqin.liu@linaro.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
For DisplayPort use we need to set WIZ_CONFIG_LANECTL register's
P_STANDARD_MODE bits to "mode 3". In the DisplayPort use also the
P_ENABLE bits of the same register are set to P_ENABLE instead of
P_ENABLE_FORCE, so that the DisplayPort driver can enable and disable
the lane as needed. The DisplayPort mode is selected according to
"cdns,phy-type"-properties found in link subnodes under the managed
serdes (see "ti,sierra-phy-t0" and "ti,j721e-serdes-10g" devicetree
bindings for details). All other values of "cdns,phy-type"-property
but PHY_TYPE_DP will set P_STANDARD_MODE bits to 0 and P_ENABLE bits
to force enable.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The usb_get_maximum_speed() function is part of the usb-common module,
so enable it by selecting the corresponding Kconfig symbol.
While at it, also make sure to depend on USB_SUPPORT because USB_PHY
requires that. This can lead to Kconfig conflicts if USB_SUPPORT is not
enabled while attempting to enable PHY_TEGRA_XUSB.
Reported-by: kbuild test robot <lkp@intel.com>
Suggested-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The usb_get_maximum_speed() function is part of the usb-common module,
so enable it by selecting the corresponding Kconfig symbol.
While at it, also make sure to depend on USB_SUPPORT because USB_PHY
requires that. This can lead to Kconfig conflicts if USB_SUPPORT is not
enabled while attempting to enable PHY_TEGRA_XUSB.
Reported-by: kbuild test robot <lkp@intel.com>
Suggested-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20200330101038.2422389-1-thierry.reding@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----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=deWu
-----END PGP SIGNATURE-----
Merge tag 'pci-v5.7-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Revert sysfs "rescan" renames that broke apps (Kelsey Skunberg)
- Add more 32 GT/s link speed decoding and improve the implementation
(Yicong Yang)
Resource management:
- Add support for sizing programmable host bridge apertures and fix a
related alpha Nautilus regression (Ivan Kokshaysky)
Interrupts:
- Add boot interrupt quirk mechanism for Xeon chipsets and document
boot interrupts (Sean V Kelley)
PCIe native device hotplug:
- When possible, disable in-band presence detect and use PDS
(Alexandru Gagniuc)
- Add DMI table for devices that don't use in-band presence detection
but don't advertise that correctly (Stuart Hayes)
- Fix hang when powering slots up/down via sysfs (Lukas Wunner)
- Fix an MSI interrupt race (Stuart Hayes)
Virtualization:
- Add ACS quirks for Zhaoxin devices (Raymond Pang)
Error handling:
- Add Error Disconnect Recover (EDR) support so firmware can report
devices disconnected via DPC and we can try to recover (Kuppuswamy
Sathyanarayanan)
Peer-to-peer DMA:
- Add Intel Sky Lake-E Root Ports B, C, D to the whitelist (Andrew
Maier)
ASPM:
- Reduce severity of common clock config message (Chris Packham)
- Clear the correct bits when enabling L1 substates, so we don't go
to the wrong state (Yicong Yang)
Endpoint framework:
- Replace EPF linkup ops with notifier call chain and improve locking
(Kishon Vijay Abraham I)
- Fix concurrent memory allocation in OB address region (Kishon Vijay
Abraham I)
- Move PF function number assignment to EPC core to support multiple
function creation methods (Kishon Vijay Abraham I)
- Fix issue with clearing configfs "start" entry (Kunihiko Hayashi)
- Fix issue with endpoint MSI-X ignoring BAR Indicator and Table
Offset (Kishon Vijay Abraham I)
- Add support for testing DMA transfers (Kishon Vijay Abraham I)
- Add support for testing > 10 endpoint devices (Kishon Vijay Abraham I)
- Add support for tests to clear IRQ (Kishon Vijay Abraham I)
- Add common DT schema for endpoint controllers (Kishon Vijay Abraham I)
Amlogic Meson PCIe controller driver:
- Add DT bindings for AXG PCIe PHY, shared MIPI/PCIe analog PHY (Remi
Pommarel)
- Add Amlogic AXG PCIe PHY, AXG MIPI/PCIe analog PHY drivers (Remi
Pommarel)
Cadence PCIe controller driver:
- Add Root Complex/Endpoint DT schema for Cadence PCIe (Kishon Vijay
Abraham I)
Intel VMD host bridge driver:
- Add two VMD Device IDs that require bus restriction mode (Sushma
Kalakota)
Mobiveil PCIe controller driver:
- Refactor and modularize mobiveil driver (Hou Zhiqiang)
- Add support for Mobiveil GPEX Gen4 host (Hou Zhiqiang)
Microsoft Hyper-V host bridge driver:
- Add support for Hyper-V PCI protocol version 1.3 and
PCI_BUS_RELATIONS2 (Long Li)
- Refactor to prepare for virtual PCI on non-x86 architectures (Boqun
Feng)
- Fix memory leak in hv_pci_probe()'s error path (Dexuan Cui)
NVIDIA Tegra PCIe controller driver:
- Use pci_parse_request_of_pci_ranges() (Rob Herring)
- Add support for endpoint mode and related DT updates (Vidya Sagar)
- Reduce -EPROBE_DEFER error message log level (Thierry Reding)
Qualcomm PCIe controller driver:
- Restrict class fixup to specific Qualcomm devices (Bjorn Andersson)
Synopsys DesignWare PCIe controller driver:
- Refactor core initialization code for endpoint mode (Vidya Sagar)
- Fix endpoint MSI-X to use correct table address (Kishon Vijay
Abraham I)
TI DRA7xx PCIe controller driver:
- Fix MSI IRQ handling (Vignesh Raghavendra)
TI Keystone PCIe controller driver:
- Allow AM654 endpoint to raise MSI-X interrupt (Kishon Vijay Abraham I)
Miscellaneous:
- Quirk ASMedia XHCI USB to avoid "PME# from D0" defect (Kai-Heng
Feng)
- Use ioremap(), not phys_to_virt(), for platform ROM to fix video
ROM mapping with CONFIG_HIGHMEM (Mikel Rychliski)"
* tag 'pci-v5.7-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (96 commits)
misc: pci_endpoint_test: remove duplicate macro PCI_ENDPOINT_TEST_STATUS
PCI: tegra: Print -EPROBE_DEFER error message at debug level
misc: pci_endpoint_test: Use full pci-endpoint-test name in request_irq()
misc: pci_endpoint_test: Fix to support > 10 pci-endpoint-test devices
tools: PCI: Add 'e' to clear IRQ
misc: pci_endpoint_test: Add ioctl to clear IRQ
misc: pci_endpoint_test: Avoid using module parameter to determine irqtype
PCI: keystone: Allow AM654 PCIe Endpoint to raise MSI-X interrupt
PCI: dwc: Fix dw_pcie_ep_raise_msix_irq() to get correct MSI-X table address
PCI: endpoint: Fix ->set_msix() to take BIR and offset as arguments
misc: pci_endpoint_test: Add support to get DMA option from userspace
tools: PCI: Add 'd' command line option to support DMA
misc: pci_endpoint_test: Use streaming DMA APIs for buffer allocation
PCI: endpoint: functions/pci-epf-test: Print throughput information
PCI: endpoint: functions/pci-epf-test: Add DMA support to transfer data
PCI: pciehp: Fix MSI interrupt race
PCI: pciehp: Fix indefinite wait on sysfs requests
PCI: endpoint: Fix clearing start entry in configfs
PCI: tegra: Add support for PCIe endpoint mode in Tegra194
PCI: sysfs: Revert "rescan" file renames
...
Pull networking updates from David Miller:
"Highlights:
1) Fix the iwlwifi regression, from Johannes Berg.
2) Support BSS coloring and 802.11 encapsulation offloading in
hardware, from John Crispin.
3) Fix some potential Spectre issues in qtnfmac, from Sergey
Matyukevich.
4) Add TTL decrement action to openvswitch, from Matteo Croce.
5) Allow paralleization through flow_action setup by not taking the
RTNL mutex, from Vlad Buslov.
6) A lot of zero-length array to flexible-array conversions, from
Gustavo A. R. Silva.
7) Align XDP statistics names across several drivers for consistency,
from Lorenzo Bianconi.
8) Add various pieces of infrastructure for offloading conntrack, and
make use of it in mlx5 driver, from Paul Blakey.
9) Allow using listening sockets in BPF sockmap, from Jakub Sitnicki.
10) Lots of parallelization improvements during configuration changes
in mlxsw driver, from Ido Schimmel.
11) Add support to devlink for generic packet traps, which report
packets dropped during ACL processing. And use them in mlxsw
driver. From Jiri Pirko.
12) Support bcmgenet on ACPI, from Jeremy Linton.
13) Make BPF compatible with RT, from Thomas Gleixnet, Alexei
Starovoitov, and your's truly.
14) Support XDP meta-data in virtio_net, from Yuya Kusakabe.
15) Fix sysfs permissions when network devices change namespaces, from
Christian Brauner.
16) Add a flags element to ethtool_ops so that drivers can more simply
indicate which coalescing parameters they actually support, and
therefore the generic layer can validate the user's ethtool
request. Use this in all drivers, from Jakub Kicinski.
17) Offload FIFO qdisc in mlxsw, from Petr Machata.
18) Support UDP sockets in sockmap, from Lorenz Bauer.
19) Fix stretch ACK bugs in several TCP congestion control modules,
from Pengcheng Yang.
20) Support virtual functiosn in octeontx2 driver, from Tomasz
Duszynski.
21) Add region operations for devlink and use it in ice driver to dump
NVM contents, from Jacob Keller.
22) Add support for hw offload of MACSEC, from Antoine Tenart.
23) Add support for BPF programs that can be attached to LSM hooks,
from KP Singh.
24) Support for multiple paths, path managers, and counters in MPTCP.
From Peter Krystad, Paolo Abeni, Florian Westphal, Davide Caratti,
and others.
25) More progress on adding the netlink interface to ethtool, from
Michal Kubecek"
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2121 commits)
net: ipv6: rpl_iptunnel: Fix potential memory leak in rpl_do_srh_inline
cxgb4/chcr: nic-tls stats in ethtool
net: dsa: fix oops while probing Marvell DSA switches
net/bpfilter: remove superfluous testing message
net: macb: Fix handling of fixed-link node
net: dsa: ksz: Select KSZ protocol tag
netdevsim: dev: Fix memory leak in nsim_dev_take_snapshot_write
net: stmmac: add EHL 2.5Gbps PCI info and PCI ID
net: stmmac: add EHL PSE0 & PSE1 1Gbps PCI info and PCI ID
net: stmmac: create dwmac-intel.c to contain all Intel platform
net: dsa: bcm_sf2: Support specifying VLAN tag egress rule
net: dsa: bcm_sf2: Add support for matching VLAN TCI
net: dsa: bcm_sf2: Move writing of CFP_DATA(5) into slicing functions
net: dsa: bcm_sf2: Check earlier for FLOW_EXT and FLOW_MAC_EXT
net: dsa: bcm_sf2: Disable learning for ASP port
net: dsa: b53: Deny enslaving port 7 for 7278 into a bridge
net: dsa: b53: Prevent tagged VLAN on port 7 for 7278
net: dsa: b53: Restore VLAN entries upon (re)configuration
net: dsa: bcm_sf2: Fix overflow checks
hv_netvsc: Remove unnecessary round_up for recv_completion_cnt
...
The phy-gmii-sel can be only auto selected in Kconfig and now the pretty
complex Kconfig dependencies are defined for phy-gmii-sel driver, which
also need to be updated every time phy-gmii-sel is re-used for any new
networking driver.
Simplify Kconfig definition for phy-gmii-sel PHY driver - drop all
dependencies and from networking drivers and rely on using 'imply
PHY_TI_GMII_SEL' in Kconfig definitions for networking drivers instead.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Tested-by: Murali Karicheri <m-karicheri2@ti.com>
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
*) Rename and Re-design phy-cadence-dp driver to phy-cadence-torrent driver
*) Add new PHY driver for Qualcomm 28nm Hi-Speed USB PHY
*) Add new PHY driver for Qualcomm Super Speed PHY in QCS404
*) Add support for Qualcomm PCIe QMP/QHP PHY in SDM845 to phy-qcom-qmp driver
*) Add support for Qualcomm UFS PHY in MSM8996 to phy-qcom-qmp driver
*) Add support for an additional reference clock in Mediatek phy-mtk-tphy driver
*) Add support for configuring tuning parameters in Mediatek phy-mtk-tphy driver
*) Add support for GMII PHY in TI K3 AM654x/J721E SoCs to phy-gmii-sel driver
*) Add support for USB2 PHY in Amlogic A1 SoC Family to phy-meson-g12a-usb2
driver
*) Add support for USB3/USB2/PCIe PHY in Socionext Pro5 SoC to
phy-uniphier-usb3ss/phy-uniphier-usb3hs/phy-uniphier-pcie driver respectively
*) Add support for QUSB2 PHY in Qualcomm SC7180 in driver
*) Convert dt-bindings of Cadence DP, Qualcomm QUSB2 to YAML format
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
-----BEGIN PGP SIGNATURE-----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=+CzV
-----END PGP SIGNATURE-----
Merge tag 'phy-for-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-next
Kishon writes:
phy: for 5.7
*) Rename and Re-design phy-cadence-dp driver to phy-cadence-torrent driver
*) Add new PHY driver for Qualcomm 28nm Hi-Speed USB PHY
*) Add new PHY driver for Qualcomm Super Speed PHY in QCS404
*) Add support for Qualcomm PCIe QMP/QHP PHY in SDM845 to phy-qcom-qmp driver
*) Add support for Qualcomm UFS PHY in MSM8996 to phy-qcom-qmp driver
*) Add support for an additional reference clock in Mediatek phy-mtk-tphy driver
*) Add support for configuring tuning parameters in Mediatek phy-mtk-tphy driver
*) Add support for GMII PHY in TI K3 AM654x/J721E SoCs to phy-gmii-sel driver
*) Add support for USB2 PHY in Amlogic A1 SoC Family to phy-meson-g12a-usb2
driver
*) Add support for USB3/USB2/PCIe PHY in Socionext Pro5 SoC to
phy-uniphier-usb3ss/phy-uniphier-usb3hs/phy-uniphier-pcie driver respectively
*) Add support for QUSB2 PHY in Qualcomm SC7180 in driver
*) Convert dt-bindings of Cadence DP, Qualcomm QUSB2 to YAML format
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
* tag 'phy-for-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy: (52 commits)
phy: qcom-qusb2: Add new overriding tuning parameters in QUSB2 V2 PHY
phy: qcom-qusb2: Add support for overriding tuning parameters in QUSB2 V2 PHY
dt-bindings: phy: qcom-qusb2: Add support for overriding Phy tuning parameters
phy: qcom-qusb2: Add generic QUSB2 V2 PHY support
dt-bindings: phy: qcom,qusb2: Add compatibles for QUSB2 V2 phy and SC7180
dt-bindings: phy: qcom,qusb2: Convert QUSB2 phy bindings to yaml
phy: rk-inno-usb2: Decrease verbosity of repeating log.
phy: amlogic: Add Amlogic A1 USB2 PHY Driver
dt-bindings: phy: Add Amlogic A1 USB2 PHY Bindings
phy: ti: gmii-sel: add support for am654x/j721e soc
dt-bindings: phy: ti: gmii-sel: add support for am654x/j721e soc
phy: qualcomm: usb: Add SuperSpeed PHY driver
dt-bindings: Add Qualcomm USB SuperSpeed PHY bindings
phy: qualcomm: Add Synopsys 28nm Hi-Speed USB PHY driver
dt-bindings: phy: Add Qualcomm Synopsys Hi-Speed USB PHY binding
dt-bindings: phy: remove qcom-dwc3-usb-phy
phy: phy-mtk-tphy: add a new reference clock
phy: phy-mtk-tphy: remove unused u3phya_ref clock
phy: phy-mtk-tphy: make the ref clock optional
phy: phy-mtk-tphy: add a property for internal resistance
...
Added support for overriding bias-ctrl-value,charge-ctrl-value and
hsdisc-trim-value params for QUSB2 V2 PHY
Signed-off-by: Sandeep Maheswaram <sanm@codeaurora.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Added new structure for overriding tuning parameters in QUSB2 V2 PHY as the
override params are increased due to usage of generic QUSB2 V2 phy table.
Signed-off-by: Sandeep Maheswaram <sanm@codeaurora.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add generic QUSB2 V2 PHY table so the respective phys
can use the same table.
Signed-off-by: Sandeep Maheswaram <sanm@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
phy-rockchip-inno-usb2 logs the message
"phy-ff2c0000.syscon:usb2-phy@100.2: charger = INVALID_CHARGER"
constantly with a frequency of about 1 Hz and a verbosity level
of INFO. As this is clearly annoying, this patch decreases
the log level to DEBUG.
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This adds support for the USB2 PHY found in the Amlogic A1 SoC Family.
It supports host mode only.
Signed-off-by: Yue Wang <yue.wang@amlogic.com>
Signed-off-by: Hanjie Lin <hanjie.lin@amlogic.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
TI AM654x/J721E SoCs have the same PHY interface selection mechanism for
CPSWx subsystem as TI SoCs (AM3/4/5/DRA7), but registers and bit-fields
placement is different.
This patch adds corresponding support for TI AM654x/J721E SoCs PHY
interface selection.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Controls Qualcomm's SS PHY 1.0.0 implemented on various SoCs on both the
20nm and 28nm process nodes.
Based on Sriharsha Allenki's <sallenki@codeaurora.org> original code.
[bod: Removed dependency on extcon.
Switched to gpio-usb-conn to handle VBUS On/Off
Switched to usb-role-switch to bind gpio-usb-conn to DWC3]
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Cc: Jorge Ramirez-Ortiz <jorge.ramirez.ortiz@gmail.com>
Cc: Sriharsha Allenki's <sallenki@codeaurora.org>
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: linux-arm-msm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Tested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Adds Qualcomm 28nm Hi-Speed USB PHY driver support. This PHY is usually
paired with Synopsys DWC3 USB controllers on Qualcomm SoCs.
The PHY can come in two flavours femtoPHY or picoPHY. This commit adds
support for the femtoPHY with the possibility of extending to the picoPHY
with additional future commits. Both PHYs are on a 28 nanometer process
node.
[bod: Updated qcom_snps_hsphy_set_mode to match new method signature
Added disjunct on mode > 0
Removed regulator_set_voltage() in favour of setting floor in dts
Removed 'snps' and from driver name
Extended commit log to mention femtoPHY and picoPHY for future
reference.]
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Jorge Ramirez-Ortiz <jorge.ramirez.ortiz@gmail.com>
Cc: linux-arm-msm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Tested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Usually the digital and analog phys use the same reference clock,
but some platforms have two separate reference clocks for each of
them, so add another optional clock to support them.
In order to keep the clock names consistent with PHY IP's, change
the da_ref for analog phy and ref clock for digital phy.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The u3phya_ref clock is already moved into sub-node, and
renamed as ref clock, no used anymore now, so remove it,
this can avoid confusion when support new platforms
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Sometimes the reference clock of USB3 PHY comes from oscillator
directly, and no need refer to a fixed-clock in DTS anymore
if make it optional.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This is used to tune J-K voltage by internal R (resistance), the
range is [0, 31], the resistance value is about 6.9K ohm for 0,
3.8K ohm for 31, and the step is 1K ohm
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This is used to tune the threshold of disconnect, the index range
is [0, 15], the threshold voltage is about 400mV for 0, 700mV for
15, and the step is 20mV.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Arguments are supposed to be ordered high then low.
Signed-off-by: Joe Perches <joe@perches.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The PCIe PHY initialization requires the attached device to be present,
which is primarily achieved by the PCI controller driver. So move the
logic from init/exit to power_on/power_off.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: John Stultz <john.stultz@linaro.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Since this phy is shared by multiple devices including USB and PCIe,
it is necessary to determine which device use this phy.
This patch adds SoC-dependent functions to determine a device using
this phy.
When there is 'socionext,syscon' property in the pcie-phy node,
the driver calls SoC-dependt function instead of checking .has_syscon
in SoC-dependent data. The function configures the system controller
to use phy for PCIe.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add legacy SoC support that needs to manage gio clock and reset and to skip
setting unimplemented phy parameters. This supports Pro5.
This specifies only 1 port use because Pro5 doesn't set it in the power-on
sequence.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
In case of using default parameters, communication failure might occur
in rare cases. This sets Rx sync mode parameter to avoid the issue.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add legacy SoC support that needs to manage gio clock and reset.
This supports Pro5.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Pro5 SoC has same scheme of USB3 ss-phy as Pro4, so the data for Pro5 is
equivalent to Pro4.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Use devm_platform_ioremap_resource() to simplify the code.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The support for the 14nm MSM8996 UFS PHY is currently handled by the
UFS-specific 14nm QMP driver, due to the earlier need for additional
operations beyond the standard PHY API.
Add support for this PHY to the common QMP driver, to allow us to remove
the old driver.
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Implement single link subnode support to the phy driver.
Add reset support including PHY reset and individual lane reset.
Signed-off-by: Swapnil Jakhade <sjakhade@cadence.com>
Signed-off-by: Yuti Amonkar <yamonkar@cadence.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add platform dependent initialization data for Torrent PHY used in TI's
J721E SoC.
Signed-off-by: Swapnil Jakhade <sjakhade@cadence.com>
Signed-off-by: Yuti Amonkar <yamonkar@cadence.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Use regmap to read and write DPTX specific PHY registers.
Signed-off-by: Swapnil Jakhade <sjakhade@cadence.com>
Signed-off-by: Yuti Amonkar <yamonkar@cadence.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Use regmap for accessing Torrent PHY registers. Modify register offsets
as defined in Torrent PHY user guide. Abstract address calculation
using regmap APIs.
Signed-off-by: Swapnil Jakhade <sjakhade@cadence.com>
Signed-off-by: Yuti Amonkar <yamonkar@cadence.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add support for PHY configuration APIs. These will mainly reconfigure
link rate, number of lanes, voltage swing and pre-emphasis values.
Signed-off-by: Swapnil Jakhade <sjakhade@cadence.com>
Signed-off-by: Yuti Amonkar <yamonkar@cadence.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add a separate function to set different power state values.
Use uniform polling timeout value. Also check return values
of functions for proper error handling.
Signed-off-by: Swapnil Jakhade <sjakhade@cadence.com>
Signed-off-by: Yuti Amonkar <yamonkar@cadence.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add a wrapper function to write Torrent PHY registers to improve
code readability.
Signed-off-by: Swapnil Jakhade <sjakhade@cadence.com>
Signed-off-by: Yuti Amonkar <yamonkar@cadence.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
- Change private data struct cdns_dp_phy to cdns_torrent_phy
- Change module description and registration accordingly
- Generic torrent functions have prefix cdns_torrent_phy_*
- Functions specific to Torrent phy for DisplayPort are prefixed as
cdns_torrent_dp_*
Signed-off-by: Swapnil Jakhade <sjakhade@cadence.com>
Signed-off-by: Yuti Amonkar <yamonkar@cadence.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Rename Cadence DP PHY driver from phy-cadence-dp to phy-cadence-torrent
to make it more generic for future use. Modifiy Makefile and Kconfig
accordingly. Also, change driver compatible from "cdns,dp-phy" to
"cdns,torrent-phy".This will not affect ABI as the driver has never
been functional, and therefore do not exist in any active use case.
Signed-off-by: Yuti Amonkar <yamonkar@cadence.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
I have hit the following build error:
armv7a-hardfloat-linux-gnueabi-ld: drivers/phy/tegra/xusb.o: in function `tegra_xusb_port_unregister':
xusb.c:(.text+0x2ac): undefined reference to `usb_remove_phy'
armv7a-hardfloat-linux-gnueabi-ld: drivers/phy/tegra/xusb.o: in function `tegra_xusb_setup_ports':
xusb.c:(.text+0xf30): undefined reference to `usb_add_phy_dev'
PHY_TEGRA_XUSB should select USB_PHY because it uses symbols defined in
the code enabled by that.
Fixes: 23babe30fb45d ("phy: tegra: xusb: Add usb-phy support")
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The device-managed allocation API doesn't work well with the life-cycle
of device objects. Since ports have device objects allocated within, it
can lead to situations where these devices need to stay around until
after their parent pad controller has been unbound from its driver. The
device-managed memory allocated for the port objects will, however, get
freed when the pad controller unbinds from the driver. This can cause
use-after-free errors down the road.
Note that the device is deleted as part of the driver unbind operation,
so there isn't much that can be done with it after that point, but the
memory still needs to stay around to ensure none of the references are
invalidated.
One situation where this arises is when a VBUS supply is associated with
a USB 2 or 3 port. When that supply is released using regulator_put() an
SRCU call will queue the release of the device link connecting the port
and the regulator after a grace period. This means that the regulator is
going to keep on to the last reference of the port device even after the
pad controller driver was unbound (which is when the memory backing the
port device is freed).
Fix this by allocating port objects using non-device-managed memory. Add
release callbacks for these objects so that their memory gets freed when
the last reference goes away. This decouples the port devices' lifetime
from the "active" lifetime of the pad controller (i.e. the time during
which the pad controller driver owns the device).
Signed-off-by: Thierry Reding <treding@nvidia.com>
Devices are created for each port of the XUSB pad controller. Each USB 2
and USB 3 port can potentially have an associated VBUS power supply that
needs to be removed when the device is removed.
Since port devices never bind to a driver, the driver core will not get
to perform the cleanup of device-managed resources that usually happens
on driver unbind.
Now, the driver core will also perform device-managed resource cleanup
for driver-less devices when they are released. However, when a device
link is created between the regulator and the port device, as part of
regulator_get(), the regulator takes a reference to the port device and
prevents it from being released unless regulator_put() is called, which
will never happen.
Avoid this by using the non-device-managed API and manually releasing
the regulator reference when the port is unregistered.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Probe deferral is an expected error condition that will usually be
recovered from. Print such error messages at debug level to make them
available for diagnostic purposes when building with debugging enabled
and hide them otherwise to not spam the kernel log with them.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Deferred probe is an expected return value for tegra_fuse_readl().
Given that the driver deals with it properly, there's no need to
output a warning that may potentially confuse users.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add support for the XUSB pad controller found on Tegra194 SoCs. It is
mostly similar to the same IP found on Tegra186, but the number of
pads exposed differs, as do the programming sequences. Because most of
the Tegra194 XUSB PADCTL registers definition and programming sequence
are the same as Tegra186, Tegra194 XUSB PADCTL can share the same
driver, xusb-tegra186.c, with Tegra186 XUSB PADCTL.
Tegra194 XUSB PADCTL supports up to USB 3.1 Gen 2 speed, however, it
is possible for some platforms have long signal trace that could not
provide sufficient electrical environment for Gen 2 speed. This patch
adds a "maximum-speed" property to usb3 ports which can be used to
specify the maximum supported speed for any particular USB 3.1 port.
For a port that is not capable of SuperSpeedPlus, "maximum-speed"
property should carry "super-speed".
Signed-off-by: JC Kuo <jckuo@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
As xusb-tegra186.c will be reused for Tegra194, it would be good to
protect Tegra186 soc data with CONFIG_ARCH_TEGRA_186_SOC. This commit
also reshuffles Tegra186 soc data single CONFIG_ARCH_TEGRA_186_SOC
will be sufficient.
Signed-off-by: JC Kuo <jckuo@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add support for set_mode on UTMI phy. This allow XUSB host/device mode
drivers to configure the hardware to corresponding modes.
Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add support for set_mode on USB 2 phy. This allow XUSB host/device mode
drivers to configure the hardware to corresponding modes.
Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra XUSB host, device mode driver requires the USB 3 companion port
number for corresponding USB 2 port. Add API to retrieve the same.
Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com>
Reviewed-by: JC Kuo <jckuo@nvidia.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
For USB 2 ports that has usb-role-switch enabled, add usb-phy for
corresponding USB 2 phy. USB role changes from role switch are then
updated to corresponding host and device mode drivers via usb-phy notifier
block.
Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
[treding@nvidia.com: rebase onto Greg's usb-next branch]
Signed-off-by: Thierry Reding <treding@nvidia.com>
If usb-role-switch property is present in USB 2 port, register
usb-role-switch to receive usb role changes.
Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
[treding@nvidia.com: rebase onto Greg's usb-next branch]
Signed-off-by: Thierry Reding <treding@nvidia.com>
*) Fix phy_get() from erroring out if device link creation failed
*) Fix write timeouts in Motorola Mapphone mdm6600 PHY
*) Fix Broadcom brcm-sata PHY driver to write to the correct MDIO register
*) Add GMII PHY mode in supported modes of TI AM335x/437x/5xx SoCs
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
-----BEGIN PGP SIGNATURE-----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=iSMT
-----END PGP SIGNATURE-----
Merge tag 'phy-for-5.6-rc_v2' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-linus
Kishon writes:
phy: for 5.6-rc
*) Fix phy_get() from erroring out if device link creation failed
*) Fix write timeouts in Motorola Mapphone mdm6600 PHY
*) Fix Broadcom brcm-sata PHY driver to write to the correct MDIO register
*) Add GMII PHY mode in supported modes of TI AM335x/437x/5xx SoCs
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
* tag 'phy-for-5.6-rc_v2' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy:
phy: mapphone-mdm6600: Fix timeouts by adding wake-up handling
phy: brcm-sata: Correct MDIO operations for 40nm platforms
phy: ti: gmii-sel: do not fail in case of gmii
phy: ti: gmii-sel: fix set of copy-paste errors
phy: core: Fix phy_get() to not return error on link creation failure
phy: mapphone-mdm6600: Fix write timeouts with shorter GPIO toggle interval
This adds support for the PCI PHY found in the Amlogic AXG SoC Family.
This will allow to mutualize code in pci-meson.c between AXG and G12A
SoC.
This PHY also uses and chains an analog PHY, which on AXG platform
is needed to have reliable PCIe communication.
Signed-off-by: Remi Pommarel <repk@triplefau.lt>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
This adds support for the MIPI analog PHY which is also used for PCIE
found in the Amlogic AXG SoC Family.
MIPI or PCIE selection is done by the #phy-cells, making the mode
static and exclusive.
For now only PCIE functionality is supported.
This PHY will be used to replace the mipi_enable clock gating logic
which was mistakenly added in the clock subsystem. This also activates
a non documented band gap bit in those registers that allows reliable
PCIE clock signal generation on AXG platforms.
Signed-off-by: Remi Pommarel <repk@triplefau.lt>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
We have an interrupt handler for the wake-up GPIO pin, but we're missing
the code to wake-up the system. This can cause timeouts receiving data
for the UART that shares the wake-up GPIO pin with the USB PHY.
All we need to do is just wake the system and kick the autosuspend
timeout to fix the issue.
Fixes: 5d1ebbda03 ("phy: mapphone-mdm6600: Add USB PHY driver for MDM6600 on Droid 4")
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Michael Scott <hashcode0f@gmail.com>
Cc: NeKit <nekit1000@gmail.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
qcom_qmp_phy_init() is extended to support the additional register
writes needed in PCS MISC and the appropriate sequences and resources
are defined for the GEN2 PCIe QMP PHY found in SDM845.
Tested-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The logic to write to MDIO registers on 40nm platforms was wrong
because it would use the port number as an offset from the base address
rather than the bank address of the PHY. This is hardly noticeable
because the only programming we do is enabling SSC or not, which is not
really causing an observable functional change.
Correct that mistake by passing down the struct brcm_sata_port structure
down to the brcm_sata_mdio_wr() and brcm_sata_mdio_rd() functions and do
the proper offsetting for 28nm, respectively 40nm platforms from there.
This means that brcm_sata_pcb_base() is now useless and is therefore
removed.
Fixes: c1602a1a0f ("phy: phy_brcmstb_sata: add support for MIPS-based platforms")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The "gmii" PHY interface mode is supported on TI AM335x/437x/5xx SoCs, so
don't fail if it's selected.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
- under PHY_INTERFACE_MODE_MII the 'mode' func parameter is assigned
instead of 'gmii_sel_mode' and it's working only because the default value
'gmii_sel_mode' is set to 0.
- console outputs use 'rgmii_id' and 'mode' values to print PHY mode
instead of using 'submode' value which is representing PHY interface mode
now.
This patch fixes above two cases.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
commit 987351e1ea ("phy: core: Add consumer device link support")
added device link support between PHY consumer and PHY provider.
However certain peripherals (DWC3 ULPI) have cyclic dependency
between the PHY provider and PHY consumer causing the device link
creation to fail.
Instead of erroring out on failure to create device link, only add a
debug print to indicate device link creation failed to get USB
working again in multiple platforms.
Fixes: 987351e1ea ("phy: core: Add consumer device link support")
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Alexandre TORGUE <alexandre.torgue@st.com>
I've noticed that when writing data to the modem the writes can time out
at some point eventually. Looks like kicking the modem idle GPIO every
600 ms instead of once a second fixes the issue. Note that this rate is
different from our runtime PM autosuspend rate MDM6600_MODEM_IDLE_DELAY_MS
that we still want to keep at 1 second, so let's add a separate define for
PHY_MDM6600_IDLE_KICK_MS.
Fixes: f7f50b2a7b ("phy: mapphone-mdm6600: Add runtime PM support for n_gsm on USB suspend")
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Michael Scott <hashcode0f@gmail.com>
Cc: NeKit <nekit1000@gmail.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Here is the big USB and Thunderbolt and PHY driver updates for 5.6-rc1.
With the advent of USB4, "Thunderbolt" has really become USB4, so the
renaming of the Kconfig option and starting to share subsystem code has
begun, hence both subsystems coming in through the same tree here.
PHY driver updates also touched USB drivers, so that is coming in
through here as well.
Major stuff included in here are:
- USB 4 initial support added (i.e. Thunderbolt)
- musb driver updates
- USB gadget driver updates
- PHY driver updates
- USB PHY driver updates
- lots of USB serial stuff fixed up
- USB typec updates
- USB-IP fixes
- lots of other smaller USB driver updates
All of these have been in linux-next for a while now (the usb-serial
tree is already tested in linux-next on its own before merged into
here), with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXjFTNw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynpKQCgrh2FoobS2x0oFg/OUHdjokQV/BYAoJGWLOmt
8S5cnsCuLq3w5qpCcBva
=PMGd
-----END PGP SIGNATURE-----
Merge tag 'usb-5.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/Thunderbolt/PHY driver updates from Greg KH:
"Here is the big USB and Thunderbolt and PHY driver updates for
5.6-rc1.
With the advent of USB4, "Thunderbolt" has really become USB4, so the
renaming of the Kconfig option and starting to share subsystem code
has begun, hence both subsystems coming in through the same tree here.
PHY driver updates also touched USB drivers, so that is coming in
through here as well.
Major stuff included in here are:
- USB 4 initial support added (i.e. Thunderbolt)
- musb driver updates
- USB gadget driver updates
- PHY driver updates
- USB PHY driver updates
- lots of USB serial stuff fixed up
- USB typec updates
- USB-IP fixes
- lots of other smaller USB driver updates
All of these have been in linux-next for a while now (the usb-serial
tree is already tested in linux-next on its own before merged into
here), with no reported issues"
[ Removed an incorrect compile test enablement for PHY_EXYNOS5250_SATA
that causes configuration warnings - Linus ]
* tag 'usb-5.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (207 commits)
Doc: ABI: add usb charger uevent
usb: phy: show USB charger type for user
usb: cdns3: fix spelling mistake and rework grammar in text
usb: phy: phy-gpio-vbus-usb: Convert to GPIO descriptors
USB: serial: cyberjack: fix spelling mistake "To" -> "Too"
USB: serial: ir-usb: simplify endpoint check
USB: serial: ir-usb: make set_termios synchronous
USB: serial: ir-usb: fix IrLAP framing
USB: serial: ir-usb: fix link-speed handling
USB: serial: ir-usb: add missing endpoint sanity check
usb: typec: fusb302: fix "op-sink-microwatt" default that was in mW
usb: typec: wcove: fix "op-sink-microwatt" default that was in mW
usb: dwc3: pci: add ID for the Intel Comet Lake -V variant
usb: typec: tcpci: mask event interrupts when remove driver
usb: host: xhci-tegra: set MODULE_FIRMWARE for tegra186
usb: chipidea: add inline for ci_hdrc_host_driver_init if host is not defined
usb: chipidea: handle single role for usb role class
usb: musb: fix spelling mistake: "periperal" -> "peripheral"
phy: ti: j721e-wiz: Fix build error without CONFIG_OF_ADDRESS
USB: usbfs: Always unlink URBs in reverse order
...
If CONFIG_OF_ADDRESS is not set and COMPILE_TEST=y, the following
error is seen while building phy-j721e-wiz.c
drivers/phy/ti/phy-j721e-wiz.o: In function `wiz_remove':
phy-j721e-wiz.c:(.text+0x1a): undefined reference to
`of_platform_device_destroy'
Fix the config dependency for PHY_J721E_WIZ here.
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: 091876cc35 ("phy: ti: j721e-wiz: Add support for WIZ module present in TI J721E SoC")
Signed-off-by: Hongbo Yao <yaohongbo@huawei.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Link: https://lore.kernel.org/r/20200117212310.2864-1-kishon@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
*) Add support in PHY core to create link between PHY consumer and PHY
provider
*) Add DisplayPort PHY configuration set to be used for negotiating the
configurations to be used between DisplayPort controller and
DisplayPort PHY
*) Add PHY wrapper driver (configure inputs to Cadence Sierra PHY) for
TI's J721E SoC and adapt Cadence Sierra PHY driver to be used for
J721E SoC (Supports USB and PCIe)
*) Add PHY driver for eMMC PHY in Intel LGM SoC
*) Add PHY support for 7216 and 7211 Broadcom SoCs which uses the new
Synopsys USB Controller
*) Add support for 16nm SATA PHY present in Broadcom 7216 SoC
*) Fix lost packet issue, fix MDIO from getting inaccessible, fix
occasional transaction failures, fix USB driver from crashing in
Broadcom USB PHY driver
*) Fix missing PCS SW reset in UFS PHY of Qualcomm SM8150
*) Use "struct phy_configure_opts_mipi_dphy" to pass parameters from
display controller to rockchip-inno-dsidphy
*) Other cleanups including compile testing for some of the PHY drivers,
fixing Kconfig indentation, duplicate writes in drivers etc.,
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
-----BEGIN PGP SIGNATURE-----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=76zg
-----END PGP SIGNATURE-----
Merge tag 'phy-for-5.6_v2' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-next
Kishon writes:
phy: for 5.6
*) Add support in PHY core to create link between PHY consumer and PHY
provider
*) Add DisplayPort PHY configuration set to be used for negotiating the
configurations to be used between DisplayPort controller and
DisplayPort PHY
*) Add PHY wrapper driver (configure inputs to Cadence Sierra PHY) for
TI's J721E SoC and adapt Cadence Sierra PHY driver to be used for
J721E SoC (Supports USB and PCIe)
*) Add PHY driver for eMMC PHY in Intel LGM SoC
*) Add PHY support for 7216 and 7211 Broadcom SoCs which uses the new
Synopsys USB Controller
*) Add support for 16nm SATA PHY present in Broadcom 7216 SoC
*) Fix lost packet issue, fix MDIO from getting inaccessible, fix
occasional transaction failures, fix USB driver from crashing in
Broadcom USB PHY driver
*) Fix missing PCS SW reset in UFS PHY of Qualcomm SM8150
*) Use "struct phy_configure_opts_mipi_dphy" to pass parameters from
display controller to rockchip-inno-dsidphy
*) Other cleanups including compile testing for some of the PHY drivers,
fixing Kconfig indentation, duplicate writes in drivers etc.,
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
* tag 'phy-for-5.6_v2' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy: (54 commits)
dt-bindings: phy: Add PHY_TYPE_DP definition
phy: ti: j721e-wiz: Fix return value check in wiz_probe()
dt-bindings: usb: Convert Allwinner A80 USB PHY controller to a schema
phy: intel-lgm-emmc: Fix warning by adding missing MODULE_LICENSE
phy: ti: j721e-wiz: Manage typec-gpio-dir
dt-bindings: phy: ti,phy-j721e-wiz: Add Type-C dir GPIO
phy: cadence: Sierra: add phy_reset hook
phy: cadence: Sierra: remove redundant initialization of pointer regmap
phy: Add DisplayPort configuration options
phy: Enable compile testing for some of drivers
phy: mediatek: Fix Kconfig indentation
phy: intel-lgm-emmc: Add support for eMMC PHY
dt-bindings: phy: intel-emmc-phy: Add YAML schema for LGM eMMC PHY
phy: ti: j721e-wiz: Add support for WIZ module present in TI J721E SoC
dt-bindings: phy: Document WIZ (SERDES wrapper) bindings
phy: cadence: Sierra: Use correct dev pointer in cdns_sierra_phy_remove()
phy: cadence: Sierra: Set cmn_refclk_dig_div/cmn_refclk1_dig_div frequency to 25MHz
phy: cadence: Sierra: Change MAX_LANES of Sierra to 16
phy: cadence: Sierra: Check for PLL lock during PHY power on
phy: cadence: Sierra: Get reset control "array" for each link
...
In case of error, the function devm_ioremap() returns NULL pointer not
ERR_PTR(). The IS_ERR() test in the return value check should be
replaced with NULL test.
Fixes: 091876cc35 ("phy: ti: j721e-wiz: Add support for WIZ module present in TI J721E SoC")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
commit 95f1061f715e ("phy: intel-lgm-emmc: Add support for eMMC PHY")
introduces the below warning
WARNING: modpost: missing MODULE_LICENSE() in
drivers/phy/intel/phy-intel-emmc.o
Fix it by adding missing MODULE_LICENSE.
Signed-off-by: Ramuthevar Vadivel Murugan <vadivel.muruganx.ramuthevar@linux.intel.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Based on this GPIO state we need to configure LN10
bit to swap lane0 and lane1 if required (flipped connector).
Type-C companions typically need some time after the cable is
plugged before and before they reflect the correct status of
Type-C plug orientation on the DIR line.
Type-C Spec specifies CC attachment debounce time (tCCDebounce)
of 100 ms (min) to 200 ms (max).
Use the DT property to figure out if we need to add delay
or not before sampling the Type-C DIR line.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Reviewed-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Sandeep Maheswaram
Sanket Parmar
Roger Quadros
Bharat Gooty
Bjorn Andersson
Rikard Falkeborn
Peter Chen
Martin Blumenstingl
Geert Uytterhoeven
Wei Yongjun
Christophe JAILLET
Jonathan Bakker
Wesley Cheng
Jack Pham
Robert Marko
John Stultz
Jyri Sarha
Thierry Reding
Linus Torvalds
Grygorii Strashko
Greg Kroah-Hartman
Christoph Muellner
Hanjie Lin
Jorge Ramirez-Ortiz
Shawn Guo
Chunfeng Yun
Joe Perches
Kunihiko Hayashi
Swapnil Jakhade
Yuti Amonkar
Corentin Labbe
Jon Hunter
JC Kuo
Nagarjuna Kristam
Remi Pommarel
Tony Lindgren
Florian Fainelli
Kishon Vijay Abraham I
Masahiro Yamada
David S. Miller
Hongbo Yao
Ramuthevar Vadivel Murugan