[ Upstream commit 8527beb120 ]
The decision whether to enable a wake irq during suspend can not be done
based on the runtime PM state directly as a driver may use wake irqs
without implementing runtime PM. Such drivers specifically leave the
state set to the default 'suspended' and the wake irq is thus never
enabled at suspend.
Add a new wake irq flag to track whether a dedicated wake irq has been
enabled at runtime suspend and therefore must not be enabled at system
suspend.
Note that pm_runtime_enabled() can not be used as runtime PM is always
disabled during late suspend.
Fixes: 69728051f5 ("PM / wakeirq: Fix unbalanced IRQ enable for wakeirq")
Cc: 4.16+ <stable@vger.kernel.org> # 4.16+
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 259714100d ]
When the dedicated wake IRQ is level trigger, and it uses the
device's low-power status as the wakeup source, that means if the
device is not in low-power state, the wake IRQ will be triggered
if enabled; For this case, need enable the wake IRQ after running
the device's ->runtime_suspend() which make it enter low-power state.
e.g.
Assume the wake IRQ is a low level trigger type, and the wakeup
signal comes from the low-power status of the device.
The wakeup signal is low level at running time (0), and becomes
high level when the device enters low-power state (runtime_suspend
(1) is called), a wakeup event at (2) make the device exit low-power
state, then the wakeup signal also becomes low level.
------------------
| ^ ^|
---------------- | | --------------
|<---(0)--->|<--(1)--| (3) (2) (4)
if enable the wake IRQ before running runtime_suspend during (0),
a wake IRQ will arise, it causes resume immediately;
it works if enable wake IRQ ( e.g. at (3) or (4)) after running
->runtime_suspend().
This patch introduces a new status WAKE_IRQ_DEDICATED_REVERSE to
optionally support enabling wake IRQ after running ->runtime_suspend().
Suggested-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Stable-dep-of: 8527beb120 ("PM: sleep: wakeirq: fix wake irq arming")
Signed-off-by: Sasha Levin <sashal@kernel.org>
Upstream commit: fb3bd914b3
Add a mitigation for the speculative return address stack overflow
vulnerability found on AMD processors.
The mitigation works by ensuring all RET instructions speculate to
a controlled location, similar to how speculation is controlled in the
retpoline sequence. To accomplish this, the __x86_return_thunk forces
the CPU to mispredict every function return using a 'safe return'
sequence.
To ensure the safety of this mitigation, the kernel must ensure that the
safe return sequence is itself free from attacker interference. In Zen3
and Zen4, this is accomplished by creating a BTB alias between the
untraining function srso_untrain_ret_alias() and the safe return
function srso_safe_ret_alias() which results in evicting a potentially
poisoned BTB entry and using that safe one for all function returns.
In older Zen1 and Zen2, this is accomplished using a reinterpretation
technique similar to Retbleed one: srso_untrain_ret() and
srso_safe_ret().
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8974eb5882 upstream
Gather Data Sampling (GDS) is a hardware vulnerability which allows
unprivileged speculative access to data which was previously stored in
vector registers.
Intel processors that support AVX2 and AVX512 have gather instructions
that fetch non-contiguous data elements from memory. On vulnerable
hardware, when a gather instruction is transiently executed and
encounters a fault, stale data from architectural or internal vector
registers may get transiently stored to the destination vector
register allowing an attacker to infer the stale data using typical
side channel techniques like cache timing attacks.
This mitigation is different from many earlier ones for two reasons.
First, it is enabled by default and a bit must be set to *DISABLE* it.
This is the opposite of normal mitigation polarity. This means GDS can
be mitigated simply by updating microcode and leaving the new control
bit alone.
Second, GDS has a "lock" bit. This lock bit is there because the
mitigation affects the hardware security features KeyLocker and SGX.
It needs to be enabled and *STAY* enabled for these features to be
mitigated against GDS.
The mitigation is enabled in the microcode by default. Disable it by
setting gather_data_sampling=off or by disabling all mitigations with
mitigations=off. The mitigation status can be checked by reading:
/sys/devices/system/cpu/vulnerabilities/gather_data_sampling
Signed-off-by: Daniel Sneddon <daniel.sneddon@linux.intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Acked-by: Josh Poimboeuf <jpoimboe@kernel.org>
Signed-off-by: Daniel Sneddon <daniel.sneddon@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0c9d2eb5e9 upstream.
The SMBus I2C buses have limits on the size of transfers they can do but
do not factor in the register length meaning we may try to do a transfer
longer than our length limit, the core will not take care of this.
Future changes will factor this out into the core but there are a number
of users that assume current behaviour so let's just do something
conservative here.
This does not take account padding bits but practically speaking these
are very rarely if ever used on I2C buses given that they generally run
slowly enough to mean there's no issue.
Cc: stable@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Xu Yilun <yilun.xu@intel.com>
Link: https://lore.kernel.org/r/20230712-regmap-max-transfer-v1-2-80e2aed22e83@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bc64734825 upstream.
When problems were noticed with the register address not being taken
into account when limiting raw transfers with I2C devices we fixed this
in the core. Unfortunately it has subsequently been realised that a lot
of buses were relying on the prior behaviour, partly due to unclear
documentation not making it obvious what was intended in the core. This
is all more involved to fix than is sensible for a fix commit so let's
just drop the original fixes, a separate commit will fix the originally
observed problem in an I2C specific way
Fixes: 3981514180 ("regmap: Account for register length when chunking")
Fixes: c8e796895e ("regmap: spi-avmm: Fix regmap_bus max_raw_write")
Signed-off-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Xu Yilun <yilun.xu@intel.com>
Cc: stable@kernel.org
Link: https://lore.kernel.org/r/20230712-regmap-max-transfer-v1-1-80e2aed22e83@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e5d1c87220 ]
Currently, while calculating residency and latency values, right
operands may overflow if resulting values are big enough.
To prevent this, albeit unlikely case, play it safe and convert
right operands to left ones' type s64.
Found by Linux Verification Center (linuxtesting.org) with static
analysis tool SVACE.
Fixes: 30f604283e ("PM / Domains: Allow domain power states to be read from DT")
Signed-off-by: Nikita Zhandarovich <n.zhandarovich@fintech.ru>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c8e796895e ]
The max_raw_write member of the regmap_spi_avmm_bus structure is defined
as:
.max_raw_write = SPI_AVMM_VAL_SIZE * MAX_WRITE_CNT
SPI_AVMM_VAL_SIZE == 4 and MAX_WRITE_CNT == 1 so this results in a
maximum write transfer size of 4 bytes which provides only enough space to
transfer the address of the target register. It provides no space for the
value to be transferred. This bug became an issue (divide-by-zero in
_regmap_raw_write()) after the following was accepted into mainline:
commit 3981514180 ("regmap: Account for register length when chunking")
Change max_raw_write to include space (4 additional bytes) for both the
register address and value:
.max_raw_write = SPI_AVMM_REG_SIZE + SPI_AVMM_VAL_SIZE * MAX_WRITE_CNT
Fixes: 7f9fb67358 ("regmap: add Intel SPI Slave to AVMM Bus Bridge support")
Reviewed-by: Matthew Gerlach <matthew.gerlach@linux.intel.com>
Signed-off-by: Russ Weight <russell.h.weight@intel.com>
Link: https://lore.kernel.org/r/20230620202824.380313-1-russell.h.weight@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 3981514180 upstream.
Currently, when regmap_raw_write() splits the data, it uses the
max_raw_write value defined for the bus. For any bus that includes
the target register address in the max_raw_write value, the chunked
transmission will always exceed the maximum transmission length.
To avoid this problem, subtract the length of the register and the
padding from the maximum transmission.
Signed-off-by: Jim Wylder <jwylder@google.com
Link: https://lore.kernel.org/r/20230517152444.3690870-2-jwylder@google.com
Signed-off-by: Mark Brown <broonie@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit fd883d79e4 ]
There is no sense in doing a cache sync on REGCACHE_NONE regmaps.
Instead of panicking the kernel due to missing cache_ops, return an error
to client driver.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Link: https://lore.kernel.org/r/20230313071812.13577-1-alexander.stein@ew.tq-group.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5c5a7680e6 ]
struct platform_driver::remove returning an integer made driver authors
expect that returning an error code was proper error handling. However
the driver core ignores the error and continues to remove the device
because there is nothing the core could do anyhow and reentering the
remove callback again is only calling for trouble.
So this is an source for errors typically yielding resource leaks in the
error path.
As there are too many platform drivers to neatly convert them all to
return void in a single go, do it in several steps after this patch:
a) Convert all drivers to implement .remove_new() returning void instead
of .remove() returning int;
b) Change struct platform_driver::remove() to return void and so make
it identical to .remove_new();
c) Change all drivers back to .remove() now with the better prototype;
d) drop struct platform_driver::remove_new().
While this touches all drivers eventually twice, steps a) and c) can be
done one driver after another and so reduces coordination efforts
immensely and simplifies review.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20221209150914.3557650-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: c766c90faf ("media: rcar_fdp1: Fix refcount leak in probe and remove function")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 58d7668242 upstream.
For CONFIG_NO_HZ_FULL systems, the tick_do_timer_cpu cannot be offlined.
However, cpu_is_hotpluggable() still returns true for those CPUs. This causes
torture tests that do offlining to end up trying to offline this CPU causing
test failures. Such failure happens on all architectures.
Fix the repeated error messages thrown by this (even if the hotplug errors are
harmless) by asking the opinion of the nohz subsystem on whether the CPU can be
hotplugged.
[ Apply Frederic Weisbecker feedback on refactoring tick_nohz_cpu_down(). ]
For drivers/base/ portion:
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Frederic Weisbecker <frederic@kernel.org>
Cc: Frederic Weisbecker <frederic@kernel.org>
Cc: "Paul E. McKenney" <paulmck@kernel.org>
Cc: Zhouyi Zhou <zhouzhouyi@gmail.com>
Cc: Will Deacon <will@kernel.org>
Cc: Marc Zyngier <maz@kernel.org>
Cc: rcu <rcu@vger.kernel.org>
Cc: stable@vger.kernel.org
Fixes: 2987557f52 ("driver-core/cpu: Expose hotpluggability to the rest of the kernel")
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Joel Fernandes (Google) <joel@joelfernandes.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e2f06aa885 upstream.
Don't require the use of dynamic debug (or modification of the kernel to
add a #define DEBUG to the top of this file) to get the printk message
about driver probe timing. This printk is only emitted when
initcall_debug is enabled on the kernel commandline, and it isn't
immediately obvious that you have to do something else to debug boot
timing issues related to driver probe. Add a comment too so it doesn't
get converted back to pr_debug().
Fixes: eb7fbc9fb1 ("driver core: Add missing '\n' in log messages")
Cc: stable <stable@kernel.org>
Cc: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Cc: Brian Norris <briannorris@chromium.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20230412225842.3196599-1-swboyd@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 36c893d3a7 ]
When calling debugfs_lookup() the result must have dput() called on it,
otherwise the memory will leak over time. To make things simpler, just
call debugfs_lookup_and_remove() instead which handles all of the logic
at once.
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Link: https://lore.kernel.org/r/20230202141621.2296458-2-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8deb87b1e8 ]
When calling debugfs_lookup() the result must have dput() called on it,
otherwise the memory will leak over time. To make things simpler, just
call debugfs_lookup_and_remove() instead which handles all of the logic
at once.
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Link: https://lore.kernel.org/r/20230202141621.2296458-1-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0b6200e1e9 ]
When calling debugfs_lookup() the result must have dput() called on it,
otherwise the memory will leak over time. To make things simpler, just
call debugfs_lookup_and_remove() instead which handles all of the logic
at once.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e5da06b27f ]
The normal call sequence of using transport class is:
Add path:
transport_setup_device()
transport_setup_classdev() // call sas_host_setup() here
transport_add_device() // if fails, need call transport_destroy_device()
transport_configure_device()
Remove path:
transport_remove_device()
transport_remove_classdev // call sas_host_remove() here
transport_destroy_device()
If transport_add_device() fails, need call transport_destroy_device()
to free memory, but in this case, ->remove() is not called, and the
resources allocated in ->setup() are leaked. So fix these leaks by
calling ->remove() in transport_add_class_device() if it returns error.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20221115031638.3816551-1-yangyingliang@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6977b1a5d6 ]
When calling kobject_add() failed in device_add(), it will call
cleanup_glue_dir() to free resource. But in kobject_add(),
dev->kobj.parent has been set to NULL. This will cause resource leak.
The process is as follows:
device_add()
get_device_parent()
class_dir_create_and_add()
kobject_add() //kobject_get()
...
dev->kobj.parent = kobj;
...
kobject_add() //failed, but set dev->kobj.parent = NULL
...
glue_dir = get_glue_dir(dev) //glue_dir = NULL, and goto
//"Error" label
...
cleanup_glue_dir() //becaues glue_dir is NULL, not call
//kobject_put()
The preceding problem may cause insmod mac80211_hwsim.ko to failed.
sysfs: cannot create duplicate filename '/devices/virtual/mac80211_hwsim'
Call Trace:
<TASK>
dump_stack_lvl+0x8e/0xd1
sysfs_warn_dup.cold+0x1c/0x29
sysfs_create_dir_ns+0x224/0x280
kobject_add_internal+0x2aa/0x880
kobject_add+0x135/0x1a0
get_device_parent+0x3d7/0x590
device_add+0x2aa/0x1cb0
device_create_groups_vargs+0x1eb/0x260
device_create+0xdc/0x110
mac80211_hwsim_new_radio+0x31e/0x4790 [mac80211_hwsim]
init_mac80211_hwsim+0x48d/0x1000 [mac80211_hwsim]
do_one_initcall+0x10f/0x630
do_init_module+0x19f/0x5e0
load_module+0x64b7/0x6eb0
__do_sys_finit_module+0x140/0x200
do_syscall_64+0x35/0x80
entry_SYSCALL_64_after_hwframe+0x46/0xb0
</TASK>
kobject_add_internal failed for mac80211_hwsim with -EEXIST, don't try to
register things with the same name in the same directory.
Fixes: cebf8fd169 ("driver core: fix race between creating/querying glue dir and its cleanup")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Link: https://lore.kernel.org/r/20221123012042.335252-1-shaozhengchao@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f6837f34a3 ]
I got the following null-ptr-deref report while doing fault injection test:
BUG: kernel NULL pointer dereference, address: 0000000000000058
CPU: 2 PID: 278 Comm: 37-i2c-ds2482 Tainted: G B W N 6.1.0-rc3+
RIP: 0010:klist_put+0x2d/0xd0
Call Trace:
<TASK>
klist_remove+0xf1/0x1c0
device_release_driver_internal+0x196/0x210
bus_remove_device+0x1bd/0x240
device_add+0xd3d/0x1100
w1_add_master_device+0x476/0x490 [wire]
ds2482_probe+0x303/0x3e0 [ds2482]
This is how it happened:
w1_alloc_dev()
// The dev->driver is set to w1_master_driver.
memcpy(&dev->dev, device, sizeof(struct device));
device_add()
bus_add_device()
dpm_sysfs_add() // It fails, calls bus_remove_device.
// error path
bus_remove_device()
// The dev->driver is not null, but driver is not bound.
__device_release_driver()
klist_remove(&dev->p->knode_driver) <-- It causes null-ptr-deref.
// normal path
bus_probe_device() // It's not called yet.
device_bind_driver()
If dev->driver is set, in the error path after calling bus_add_device()
in device_add(), bus_remove_device() is called, then the device will be
detached from driver. But device_bind_driver() is not called yet, so it
causes null-ptr-deref while access the 'knode_driver'. To fix this, set
dev->driver to null in the error path before calling bus_remove_device().
Fixes: 57eee3d23e ("Driver core: Call device_pm_add() after bus_add_device() in device_add()")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20221205034904.2077765-1-yangyingliang@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9be182da0a ]
In test_async_probe_init, second set of asynchronous devices are saved
in sync_dev[sync_id], which should be async_dev[async_id].
This makes these devices not unregistered when exit.
> modprobe test_async_driver_probe && \
> modprobe -r test_async_driver_probe && \
> modprobe test_async_driver_probe
...
> sysfs: cannot create duplicate filename '/devices/platform/test_async_driver.4'
> kobject_add_internal failed for test_async_driver.4 with -EEXIST,
don't try to register things with the same name in the same directory.
Fixes: 57ea974fb8 ("driver core: Rewrite test_async_driver_probe to cover serialization and NUMA affinity")
Signed-off-by: Chen Zhongjin <chenzhongjin@huawei.com>
Link: https://lore.kernel.org/r/20221125063541.241328-1-chenzhongjin@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 39af728649 ]
The 'parent' returned by fwnode_graph_get_port_parent()
with refcount incremented when 'prev' is not NULL, it
needs be put when finish using it.
Because the parent is const, introduce a new variable to
store the returned fwnode, then put it before returning
from fwnode_graph_get_next_endpoint().
Fixes: b5b41ab6b0 ("device property: Check fwnode->secondary in fwnode_graph_get_next_endpoint()")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-and-tested-by: Daniel Scally <djrscally@gmail.com>
Link: https://lore.kernel.org/r/20221123022542.2999510-1-yangyingliang@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 27c0d21734 upstream.
When a driver registers with a bus, it will attempt to match with every
device on the bus through the __driver_attach() function. Currently, if
the bus_type.match() function encounters an error that is not
-EPROBE_DEFER, __driver_attach() will return a negative error code, which
causes the driver registration logic to stop trying to match with the
remaining devices on the bus.
This behavior is not correct; a failure while matching a driver to a
device does not mean that the driver won't be able to match and bind
with other devices on the bus. Update the logic in __driver_attach()
to reflect this.
Fixes: 656b8035b0 ("ARM: 8524/1: driver cohandle -EPROBE_DEFER from bus_type.match()")
Cc: stable@vger.kernel.org
Cc: Saravana Kannan <saravanak@google.com>
Signed-off-by: Isaac J. Manjarres <isaacmanjarres@google.com>
Link: https://lore.kernel.org/r/20220921001414.4046492-1-isaacmanjarres@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8c3e8a6bdb ]
If class_add_groups() returns error, the 'cp->subsys' need be
unregister, and the 'cp' need be freed.
We can not call kset_unregister() here, because the 'cls' will
be freed in callback function class_release() and it's also
freed in caller's error path, it will cause double free.
So fix this by calling kobject_del() and kfree_const(name) to
cleanup kobject. Besides, call kfree() to free the 'cp'.
Fault injection test can trigger this:
unreferenced object 0xffff888102fa8190 (size 8):
comm "modprobe", pid 502, jiffies 4294906074 (age 49.296s)
hex dump (first 8 bytes):
70 6b 74 63 64 76 64 00 pktcdvd.
backtrace:
[<00000000e7c7703d>] __kmalloc_track_caller+0x1ae/0x320
[<000000005e4d70bc>] kstrdup+0x3a/0x70
[<00000000c2e5e85a>] kstrdup_const+0x68/0x80
[<000000000049a8c7>] kvasprintf_const+0x10b/0x190
[<0000000029123163>] kobject_set_name_vargs+0x56/0x150
[<00000000747219c9>] kobject_set_name+0xab/0xe0
[<0000000005f1ea4e>] __class_register+0x15c/0x49a
unreferenced object 0xffff888037274000 (size 1024):
comm "modprobe", pid 502, jiffies 4294906074 (age 49.296s)
hex dump (first 32 bytes):
00 40 27 37 80 88 ff ff 00 40 27 37 80 88 ff ff .@'7.....@'7....
00 00 00 00 ad 4e ad de ff ff ff ff 00 00 00 00 .....N..........
backtrace:
[<00000000151f9600>] kmem_cache_alloc_trace+0x17c/0x2f0
[<00000000ecf3dd95>] __class_register+0x86/0x49a
Fixes: ced6473e74 ("driver core: class: add class_groups support")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20221026082803.3458760-1-yangyingliang@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bc80c2e438 ]
Calling __rpm_callback() from rpm_idle() after adding device links
support to the former is a clear mistake.
Not only it causes rpm_idle() to carry out unnecessary actions, but it
is also against the assumption regarding the stability of PM-runtime
status across __rpm_callback() invocations, because rpm_suspend() and
rpm_resume() may run in parallel with __rpm_callback() when it is called
by rpm_idle() and the device's PM-runtime status can be updated by any
of them.
Fixes: 21d5c57b37 ("PM / runtime: Use device links")
Link: https://lore.kernel.org/linux-pm/36aed941-a73e-d937-2721-4f0decd61ce0@quicinc.com
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e0c57a5c70 ]
Platforms can provide the information about the availability of each
idle states via status flag. Platforms may have to disable one or more
idle states for various reasons like broken firmware or other unmet
dependencies.
Fix handling of such unavailable/disabled idle states by ignoring them
while parsing the states.
Fixes: a3381e3a65 ("PM / domains: Fix up domain-idle-states OF parsing")
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 456797da79 upstream.
arm64's method of defining a default cpu topology requires only minimal
changes to apply to RISC-V also. The current arm64 implementation exits
early in a uniprocessor configuration by reading MPIDR & claiming that
uniprocessor can rely on the default values.
This is appears to be a hangover from prior to '3102bc0e6ac7 ("arm64:
topology: Stop using MPIDR for topology information")', because the
current code just assigns default values for multiprocessor systems.
With the MPIDR references removed, store_cpu_topolgy() can be moved to
the common arch_topology code.
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Atish Patra <atishp@rivosinc.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 25e9fbf0fd upstream.
Both __device_attach_driver() and __driver_attach() check the return
code of the bus_type.match() function to see if the device needs to be
added to the deferred probe list. After adding the device to the list,
the logic attempts to bind the device to the driver anyway, as if the
device had matched with the driver, which is not correct.
If __device_attach_driver() detects that the device in question is not
ready to match with a driver on the bus, then it doesn't make sense for
the device to attempt to bind with the current driver or continue
attempting to match with any of the other drivers on the bus. So, update
the logic in __device_attach_driver() to reflect this.
If __driver_attach() detects that a driver tried to match with a device
that is not ready to match yet, then the driver should not attempt to bind
with the device. However, the driver can still attempt to match and bind
with other devices on the bus, as drivers can be bound to multiple
devices. So, update the logic in __driver_attach() to reflect this.
Fixes: 656b8035b0 ("ARM: 8524/1: driver cohandle -EPROBE_DEFER from bus_type.match()")
Cc: stable@vger.kernel.org
Cc: Saravana Kannan <saravanak@google.com>
Reported-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Saravana Kannan <saravanak@google.com>
Signed-off-by: Isaac J. Manjarres <isaacmanjarres@google.com>
Link: https://lore.kernel.org/r/20220817184026.3468620-1-isaacmanjarres@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7ee951acd3 ]
Using bin_attributes with a 0 size causes fstat and friends to return that
0 size. This breaks userspace code that retrieves the size before reading
the file. Rather than reverting 75bd50fa84 ("drivers/base/node.c: use
bin_attribute to break the size limitation of cpumap ABI") let's put in a
size value at compile time.
For cpulist the maximum size is on the order of
NR_CPUS * (ceil(log10(NR_CPUS)) + 1)/2
which for 8192 is 20480 (8192 * 5)/2. In order to get near that you'd need
a system with every other CPU on one node. For example: (0,2,4,8, ... ).
To simplify the math and support larger NR_CPUS in the future we are using
(NR_CPUS * 7)/2. We also set it to a min of PAGE_SIZE to retain the older
behavior for smaller NR_CPUS.
The cpumap file the size works out to be NR_CPUS/4 + NR_CPUS/32 - 1
(or NR_CPUS * 9/32 - 1) including the ","s.
Add a set of macros for these values to cpumask.h so they can be used in
multiple places. Apply these to the handful of such files in
drivers/base/topology.c as well as node.c.
As an example, on an 80 cpu 4-node system (NR_CPUS == 8192):
before:
-r--r--r--. 1 root root 0 Jul 12 14:08 system/node/node0/cpulist
-r--r--r--. 1 root root 0 Jul 11 17:25 system/node/node0/cpumap
after:
-r--r--r--. 1 root root 28672 Jul 13 11:32 system/node/node0/cpulist
-r--r--r--. 1 root root 4096 Jul 13 11:31 system/node/node0/cpumap
CONFIG_NR_CPUS = 16384
-r--r--r--. 1 root root 57344 Jul 13 14:03 system/node/node0/cpulist
-r--r--r--. 1 root root 4607 Jul 13 14:02 system/node/node0/cpumap
The actual number of cpus doesn't matter for the reported size since they
are based on NR_CPUS.
Fixes: 75bd50fa84 ("drivers/base/node.c: use bin_attribute to break the size limitation of cpumap ABI")
Fixes: bb9ec13d15 ("topology: use bin_attribute to break the size limitation of cpumap ABI")
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Cc: Yury Norov <yury.norov@gmail.com>
Cc: stable@vger.kernel.org
Acked-by: Yury Norov <yury.norov@gmail.com> (for include/linux/cpumask.h)
Signed-off-by: Phil Auld <pauld@redhat.com>
Link: https://lore.kernel.org/r/20220715134924.3466194-1-pauld@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 70fe758352 ]
In __driver_attach function, There are also AA deadlock problem,
like the commit b232b02bf3 ("driver core: fix deadlock in
__device_attach").
stack like commit b232b02bf3 ("driver core: fix deadlock in
__device_attach").
list below:
In __driver_attach function, The lock holding logic is as follows:
...
__driver_attach
if (driver_allows_async_probing(drv))
device_lock(dev) // get lock dev
async_schedule_dev(__driver_attach_async_helper, dev); // func
async_schedule_node
async_schedule_node_domain(func)
entry = kzalloc(sizeof(struct async_entry), GFP_ATOMIC);
/* when fail or work limit, sync to execute func, but
__driver_attach_async_helper will get lock dev as
will, which will lead to A-A deadlock. */
if (!entry || atomic_read(&entry_count) > MAX_WORK) {
func;
else
queue_work_node(node, system_unbound_wq, &entry->work)
device_unlock(dev)
As above show, when it is allowed to do async probes, because of
out of memory or work limit, async work is not be allowed, to do
sync execute instead. it will lead to A-A deadlock because of
__driver_attach_async_helper getting lock dev.
Reproduce:
and it can be reproduce by make the condition
(if (!entry || atomic_read(&entry_count) > MAX_WORK)) untenable, like
below:
[ 370.785650] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables
this message.
[ 370.787154] task:swapper/0 state:D stack: 0 pid: 1 ppid:
0 flags:0x00004000
[ 370.788865] Call Trace:
[ 370.789374] <TASK>
[ 370.789841] __schedule+0x482/0x1050
[ 370.790613] schedule+0x92/0x1a0
[ 370.791290] schedule_preempt_disabled+0x2c/0x50
[ 370.792256] __mutex_lock.isra.0+0x757/0xec0
[ 370.793158] __mutex_lock_slowpath+0x1f/0x30
[ 370.794079] mutex_lock+0x50/0x60
[ 370.794795] __device_driver_lock+0x2f/0x70
[ 370.795677] ? driver_probe_device+0xd0/0xd0
[ 370.796576] __driver_attach_async_helper+0x1d/0xd0
[ 370.797318] ? driver_probe_device+0xd0/0xd0
[ 370.797957] async_schedule_node_domain+0xa5/0xc0
[ 370.798652] async_schedule_node+0x19/0x30
[ 370.799243] __driver_attach+0x246/0x290
[ 370.799828] ? driver_allows_async_probing+0xa0/0xa0
[ 370.800548] bus_for_each_dev+0x9d/0x130
[ 370.801132] driver_attach+0x22/0x30
[ 370.801666] bus_add_driver+0x290/0x340
[ 370.802246] driver_register+0x88/0x140
[ 370.802817] ? virtio_scsi_init+0x116/0x116
[ 370.803425] scsi_register_driver+0x1a/0x30
[ 370.804057] init_sd+0x184/0x226
[ 370.804533] do_one_initcall+0x71/0x3a0
[ 370.805107] kernel_init_freeable+0x39a/0x43a
[ 370.805759] ? rest_init+0x150/0x150
[ 370.806283] kernel_init+0x26/0x230
[ 370.806799] ret_from_fork+0x1f/0x30
To fix the deadlock, move the async_schedule_dev outside device_lock,
as we can see, in async_schedule_node_domain, the parameter of
queue_work_node is system_unbound_wq, so it can accept concurrent
operations. which will also not change the code logic, and will
not lead to deadlock.
Fixes: ef0ff68351 ("driver core: Probe devices asynchronously instead of the driver")
Signed-off-by: Zhang Wensheng <zhangwensheng5@huawei.com>
Link: https://lore.kernel.org/r/20220622074327.497102-1-zhangwensheng5@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 37101d3c71 ]
Both genpd_debug_add() and genpd_debug_remove() may be called
indirectly by other drivers while genpd_debugfs_dir is not yet
set. For example, drivers can call pm_genpd_init() in probe or
pm_genpd_init() in probe fail/cleanup path:
pm_genpd_init()
--> genpd_debug_add()
pm_genpd_remove()
--> genpd_remove()
--> genpd_debug_remove()
At this time, genpd_debug_init() may not yet be called.
genpd_debug_add() checks that if genpd_debugfs_dir is NULL, it
will return directly. Make sure this is also checked
in pm_genpd_remove(), otherwise components under debugfs root
which has the same name as other components under pm_genpd may
be accidentally removed, since NULL represents debugfs root.
Fixes: 718072ceb2 ("PM: domains: create debugfs nodes when adding power domains")
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 07358194ba upstream.
Instead of passing an extra bool argument to pm_runtime_release_supplier(),
make its callers take care of triggering a runtime-suspend of the
supplier device as needed.
No expected functional impact.
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: 5.1+ <stable@vger.kernel.org> # 5.1+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d1fe111fb6 ]
When the hwpoison page meets the filter conditions, it should not be
regarded as successful memory_failure() processing for mce handler, but
should return a distinct value, otherwise mce handler regards the error
page has been identified and isolated, which may lead to calling
set_mce_nospec() to change page attribute, etc.
Here memory_failure() return -EOPNOTSUPP to indicate that the error
event is filtered, mce handler should not take any action for this
situation and hwpoison injector should treat as correct.
Link: https://lkml.kernel.org/r/20220223082135.2769649-1-luofei@unicloud.com
Signed-off-by: luofei <luofei@unicloud.com>
Acked-by: Borislav Petkov <bp@suse.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Miaohe Lin <linmiaohe@huawei.com>
Cc: Naoya Horiguchi <naoya.horiguchi@nec.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3f05010f24 ]
We need to divide the sub-irq status register offset by register
stride to get an index for the status buffer to avoid an out of
bounds write when the register stride is greater than 1.
Fixes: a2d21848d9 ("regmap: regmap-irq: Add main status register support")
Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
Link: https://lore.kernel.org/r/20220620200644.1961936-3-aidanmacdonald.0x0@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 485037ae9a ]
When enabling a type_in_mask irq, the type_buf contents must be
AND'd with the mask of the IRQ we're enabling to avoid enabling
other IRQs by accident, which can happen if several type_in_mask
irqs share a mask register.
Fixes: bc998a7303 ("regmap: irq: handle HW using separate rising/falling edge interrupts")
Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
Link: https://lore.kernel.org/r/20220620200644.1961936-2-aidanmacdonald.0x0@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4bca7e80b6 ]
noop_backing_dev_info is used by superblocks of various
pseudofilesystems such as kdevtmpfs. After commit 10e1407310
("writeback: Fix inode->i_io_list not be protected by inode->i_lock
error") this broke because __mark_inode_dirty() started to access more
fields from noop_backing_dev_info and this led to crashes inside
locked_inode_to_wb_and_lock_list() called from __mark_inode_dirty().
Fix the problem by initializing noop_backing_dev_info before the
filesystems get mounted.
Fixes: 10e1407310 ("writeback: Fix inode->i_io_list not be protected by inode->i_lock error")
Reported-and-tested-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Reported-and-tested-by: Alexandru Elisei <alexandru.elisei@arm.com>
Reported-and-tested-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 8d50cdf8b8 upstream
Add the sysfs reporting file for Processor MMIO Stale Data
vulnerability. It exposes the vulnerability and mitigation state similar
to the existing files for the other hardware vulnerabilities.
Signed-off-by: Pawan Gupta <pawan.kumar.gupta@linux.intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5ee76c256e ]
Mounting NFS rootfs was timing out when deferred_probe_timeout was
non-zero [1]. This was because ip_auto_config() initcall times out
waiting for the network interfaces to show up when
deferred_probe_timeout was non-zero. While ip_auto_config() calls
wait_for_device_probe() to make sure any currently running deferred
probe work or asynchronous probe finishes, that wasn't sufficient to
account for devices being deferred until deferred_probe_timeout.
Commit 35a672363a ("driver core: Ensure wait_for_device_probe() waits
until the deferred_probe_timeout fires") tried to fix that by making
sure wait_for_device_probe() waits for deferred_probe_timeout to expire
before returning.
However, if wait_for_device_probe() is called from the kernel_init()
context:
- Before deferred_probe_initcall() [2], it causes the boot process to
hang due to a deadlock.
- After deferred_probe_initcall() [3], it blocks kernel_init() from
continuing till deferred_probe_timeout expires and beats the point of
deferred_probe_timeout that's trying to wait for userspace to load
modules.
Neither of this is good. So revert the changes to
wait_for_device_probe().
[1] - https://lore.kernel.org/lkml/TYAPR01MB45443DF63B9EF29054F7C41FD8C60@TYAPR01MB4544.jpnprd01.prod.outlook.com/
[2] - https://lore.kernel.org/lkml/YowHNo4sBjr9ijZr@dev-arch.thelio-3990X/
[3] - https://lore.kernel.org/lkml/Yo3WvGnNk3LvLb7R@linutronix.de/
Fixes: 35a672363a ("driver core: Ensure wait_for_device_probe() waits until the deferred_probe_timeout fires")
Cc: John Stultz <jstultz@google.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Rob Herring <robh@kernel.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Naresh Kamboju <naresh.kamboju@linaro.org>
Cc: Basil Eljuse <Basil.Eljuse@arm.com>
Cc: Ferry Toth <fntoth@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Anders Roxell <anders.roxell@linaro.org>
Cc: linux-pm@vger.kernel.org
Reported-by: Nathan Chancellor <nathan@kernel.org>
Reported-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: John Stultz <jstultz@google.com>
Signed-off-by: Saravana Kannan <saravanak@google.com>
Link: https://lore.kernel.org/r/20220526034609.480766-2-saravanak@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Rafael J. Wysocki <rafael@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b232b02bf3 ]
In __device_attach function, The lock holding logic is as follows:
...
__device_attach
device_lock(dev) // get lock dev
async_schedule_dev(__device_attach_async_helper, dev); // func
async_schedule_node
async_schedule_node_domain(func)
entry = kzalloc(sizeof(struct async_entry), GFP_ATOMIC);
/* when fail or work limit, sync to execute func, but
__device_attach_async_helper will get lock dev as
well, which will lead to A-A deadlock. */
if (!entry || atomic_read(&entry_count) > MAX_WORK) {
func;
else
queue_work_node(node, system_unbound_wq, &entry->work)
device_unlock(dev)
As shown above, when it is allowed to do async probes, because of
out of memory or work limit, async work is not allowed, to do
sync execute instead. it will lead to A-A deadlock because of
__device_attach_async_helper getting lock dev.
To fix the deadlock, move the async_schedule_dev outside device_lock,
as we can see, in async_schedule_node_domain, the parameter of
queue_work_node is system_unbound_wq, so it can accept concurrent
operations. which will also not change the code logic, and will
not lead to deadlock.
Fixes: 765230b5f0 ("driver-core: add asynchronous probing support for drivers")
Signed-off-by: Zhang Wensheng <zhangwensheng5@huawei.com>
Link: https://lore.kernel.org/r/20220518074516.1225580-1-zhangwensheng5@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 310862e574 ]
When driver_attach(drv); failed, the driver_private will be freed.
But it has been added to the bus, which caused a UAF.
To fix it, we need to delete it from the bus when failed.
Fixes: 190888ac01 ("driver core: fix possible missing of device probe")
Signed-off-by: Schspa Shi <schspa@gmail.com>
Link: https://lore.kernel.org/r/20220513112444.45112-1-schspa@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f47f758cff ]
__add_memory_block() calls both put_device() and device_unregister() when
storing the memory block into the xarray. This is incorrect because
xarray doesn't take an additional reference and device_unregister()
already calls put_device().
Triggering the issue looks really unlikely and its only effect should be
to log a spurious warning about a ref counted issue.
Link: https://lkml.kernel.org/r/d44c63d78affe844f020dc02ad6af29abc448fc4.1650611702.git.christophe.jaillet@wanadoo.fr
Fixes: 4fb6eabf10 ("drivers/base/memory.c: cache memory blocks in xarray to accelerate lookup")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Michal Hocko <mhocko@suse.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Cc: Scott Cheloha <cheloha@linux.vnet.ibm.com>
Cc: Nathan Lynch <nathanl@linux.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit da63dc84be ]
Compaction sysfs file is created via compaction_register_node in
register_node. But we forgot to remove it in unregister_node. Thus
compaction sysfs file is leaked. Using compaction_unregister_node to fix
this issue.
Link: https://lkml.kernel.org/r/20220401070905.43679-1-linmiaohe@huawei.com
Fixes: ed4a6d7f06 ("mm: compaction: add /sys trigger for per-node memory compaction")
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Rafael J. Wysocki <rafael@kernel.org>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Minchan Kim <minchan.kim@gmail.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 622d9b5577 ]
In the genpd governor we walk the list of child-domains to take into
account their next_wakeup. If the child-domain itself, doesn't have a
governor assigned to it, we can end up using the next_wakeup value before
it has been properly initialized. To prevent a possible incorrect behaviour
in the governor, let's initialize next_wakeup to KTIME_MAX.
Fixes: c79aa080fb ("PM: domains: use device's next wakeup to determine domain idle state")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 002752af7b ]
Some of the fwnode APIs might return an error pointer instead of NULL
or valid fwnode handle. The result of such API call may be considered
optional and hence the test for it is usually done in a form of
fwnode = fwnode_find_reference(...);
if (IS_ERR(fwnode))
...error handling...
Nevertheless the resulting fwnode may have bumped the reference count
and hence caller of the above API is obliged to call fwnode_handle_put().
Since fwnode may be not valid either as NULL or error pointer the check
has to be performed there. This approach uglifies the code and adds
a point of making a mistake, i.e. forgetting about error point case.
To prevent this, allow an error pointer to be passed to the fwnode APIs.
Fixes: 83b34afb6b ("device property: Introduce fwnode_find_reference()")
Reported-by: Nuno Sá <nuno.sa@analog.com>
Tested-by: Nuno Sá <nuno.sa@analog.com>
Acked-by: Nuno Sá <nuno.sa@analog.com>
Reviewed-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Michael Walle <michael@walle.cc>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c097af1d0a ]
fwnode_property_get_reference_args() searches for named properties
against a fwnode_handle, but these could instead be against the fwnode's
secondary. If the property isn't found against the primary, check the
secondary to see if it's there instead.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Link: https://lore.kernel.org/r/20211128232455.39332-1-djrscally@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 581dd69830 upstream.
Device drivers may decide to not load firmware when probed to avoid
slowing down the boot process should the firmware filesystem not be
available yet. In this case, the firmware loading request may be done
when a device file associated with the driver is first accessed. The
credentials of the userspace process accessing the device file may be
used to validate access to the firmware files requested by the driver.
Ensure that the kernel assumes the responsibility of reading the
firmware.
This was observed on Android for a graphic driver loading their firmware
when the device file (e.g. /dev/mali0) was first opened by userspace
(i.e. surfaceflinger). The security context of surfaceflinger was used
to validate the access to the firmware file (e.g.
/vendor/firmware/mali.bin).
Previously, Android configurations were not setting up the
firmware_class.path command line argument and were relying on the
userspace fallback mechanism. In this case, the security context of the
userspace daemon (i.e. ueventd) was consistently used to read firmware
files. More Android devices are now found to set firmware_class.path
which gives the kernel the opportunity to read the firmware directly
(via kernel_read_file_from_path_initns). In this scenario, the current
process credentials were used, even if unrelated to the loading of the
firmware file.
Signed-off-by: Thiébaud Weksteen <tweek@google.com>
Cc: <stable@vger.kernel.org> # 5.10
Reviewed-by: Paul Moore <paul@paul-moore.com>
Acked-by: Luis Chamberlain <mcgrof@kernel.org>
Link: https://lore.kernel.org/r/20220502004952.3970800-1-tweek@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1dc9f1a66e upstream.
When ACPI is not enabled, cpuid_topo->llc_id = cpu_topo->llc_id = -1, which
will set llc_sibling 0xff(...), this is misleading.
Don't set llc_sibling(default 0) if we don't know the cache topology.
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Wang Qing <wangqing@vivo.com>
Fixes: 37c3ec2d81 ("arm64: topology: divorce MC scheduling domain from core_siblings")
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/1649644580-54626-1-git-send-email-wangqing@vivo.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 74befa447e ]
When a driver for an interrupt controller is missing, of_irq_get()
returns -EPROBE_DEFER ad infinitum, causing
fwnode_mdiobus_phy_device_register(), and ultimately, the entire
of_mdiobus_register() call, to fail. In turn, any phy_connect() call
towards a PHY on this MDIO bus will also fail.
This is not what is expected to happen, because the PHY library falls
back to poll mode when of_irq_get() returns a hard error code, and the
MDIO bus, PHY and attached Ethernet controller work fine, albeit
suboptimally, when the PHY library polls for link status. However,
-EPROBE_DEFER has special handling given the assumption that at some
point probe deferral will stop, and the driver for the supplier will
kick in and create the IRQ domain.
Reasons for which the interrupt controller may be missing:
- It is not yet written. This may happen if a more recent DT blob (with
an interrupt-parent for the PHY) is used to boot an old kernel where
the driver didn't exist, and that kernel worked with the
vintage-correct DT blob using poll mode.
- It is compiled out. Behavior is the same as above.
- It is compiled as a module. The kernel will wait for a number of
seconds specified in the "deferred_probe_timeout" boot parameter for
user space to load the required module. The current default is 0,
which times out at the end of initcalls. It is possible that this
might cause regressions unless users adjust this boot parameter.
The proposed solution is to use the driver_deferred_probe_check_state()
helper function provided by the driver core, which gives up after some
-EPROBE_DEFER attempts, taking "deferred_probe_timeout" into consideration.
The return code is changed from -EPROBE_DEFER into -ENODEV or
-ETIMEDOUT, depending on whether the kernel is compiled with support for
modules or not.
Fixes: 66bdede495 ("of_mdio: Fix broken PHY IRQ in case of probe deferral")
Suggested-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220407165538.4084809-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0dd8d6cb9e ]
There are 4 users of mc146818_get_time() and none of them was checking
the return value from this function. Change this.
Print the appropriate warnings in callers of mc146818_get_time() instead
of in the function mc146818_get_time() itself, in order not to add
strings to rtc-mc146818-lib.c, which is kind of a library.
The callers of alpha_rtc_read_time() and cmos_read_time() may use the
contents of (struct rtc_time *) even when the functions return a failure
code. Therefore, set the contents of (struct rtc_time *) to 0x00,
which looks more sensible then 0xff and aligns with the (possibly
stale?) comment in cmos_read_time:
/*
* If pm_trace abused the RTC for storage, set the timespec to 0,
* which tells the caller that this RTC value is unusable.
*/
For consistency, do this in mc146818_get_time().
Note: hpet_rtc_interrupt() may call mc146818_get_time() many times a
second. It is very unlikely, though, that the RTC suddenly stops
working and mc146818_get_time() would consistently fail.
Only compile-tested on alpha.
Signed-off-by: Mateusz Jończyk <mat.jonczyk@o2.pl>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: linux-alpha@vger.kernel.org
Cc: x86@kernel.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20211210200131.153887-4-mat.jonczyk@o2.pl
Signed-off-by: Sasha Levin <sashal@kernel.org>
Johan Hovold
Chunfeng Yun
Borislav Petkov (AMD)
Daniel Sneddon
Mark Brown
Nikita Zhandarovich
Russ Weight
Jim Wylder
Alexander Stein
Uwe Kleine-König
Joel Fernandes (Google)
Stephen Boyd
Greg Kroah-Hartman
Yang Yingliang
Zhengchao Shao
Chen Zhongjin
Isaac J. Manjarres
Rafael J. Wysocki
Sudeep Holla
Conor Dooley
Phil Auld
Zhang Wensheng
Hsin-Yi Wang
Alexandre Chartre
luofei
Aidan MacDonald
Jan Kara
Pawan Gupta
Saravana Kannan
Schspa Shi
Christophe JAILLET
Miaohe Lin
Ulf Hansson
Andy Shevchenko
Daniel Scally
Thiébaud Weksteen
Wang Qing
Vladimir Oltean
Mateusz Jończyk
Dmitry Baryshkov