dmaengine Kconfig grew over the years, unfortunately without any
order to it. So order by core, driver and client sections, and
sort these sections alphabetically
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
dmaengine makefile grew over the years, unfortunately without any
order to it. So order by core, dmatest and driver sections and
sort these sections alphabetically
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The Kconfig for this driver is currently:
config MV_XOR
bool "Marvell XOR engine support"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Since module_init translates to device_initcall in the non-modular
case, the init ordering remains unchanged with this commit.
We leave some tags like MODULE_AUTHOR for documentation purposes.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: dmaengine@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Add support for the Analog Devices AXI-DMAC DMA controller. This controller
is a soft peripheral that can be instantiated in a FPGA and is often used
in Analog Devices' reference designs for FPGA platforms.
The peripheral has various configuration options that can be selected at
synthesis time and influence the supported features of the instantiated
peripheral, those options are represented as device-tree properties to
allow the driver to behave accordingly.
The peripheral has a zero latency architecture, which means it is possible
to switch from one to the next descriptor without any delay. This is
archived by having a internal queue which can hold multiple descriptors.
The driver supports this, which means it will submit new descriptors
directly to the hardware until the queue is full and not wait for a
descriptor to complete before the next one is submitted. Interrupts are
used for the descriptor queue flow control.
Currently the driver supports SG, cyclic and interleaved slave DMA.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch provides the fix in the cleanup routing such that client can perform
further submission by releasing the lock before calling client's callback function.
Signed-off-by: Rameshwar Prasad Sahu <rsahu@apm.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Simplifying the end return. This existed in the original code but was
flagged when refactoring of the code made it appear it's new.
coccinelle warnings: (new ones prefixed by >>)
>> drivers/dma/ioat/init.c:1018:1-3: WARNING: end returns can be simpified
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The 32bit build is creating this warning. Since we don't expect anyone
actually use this on 32bit, restrict ioatdma to be built only on x86_64.
This issue has long existed and only reason it's surfacing due to code
refactoring.
drivers/dma/ioat/dma.c: In function 'ioat_timer_event':
>> drivers/dma/ioat/dma.c:870:39: warning: passing argument 2 of 'ioat_cleanup_preamble' from incompatible pointer type
if (ioat_cleanup_preamble(ioat_chan, &phys_complete))
^
drivers/dma/ioat/dma.c:577:13: note: expected 'u64 *' but argument is of type 'dma_addr_t *'
static bool ioat_cleanup_preamble(struct ioatdma_chan *ioat_chan,
^
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Sparse reports the following with regard to locking in the
tegra_dma_global_pause() and tegra_dma_global_resume() functions:
drivers/dma/tegra20-apb-dma.c:362:9: warning: context imbalance in
'tegra_dma_global_pause' - wrong count at exit
drivers/dma/tegra20-apb-dma.c:366:13: warning: context imbalance in
'tegra_dma_global_resume' - unexpected unlock
The warning is caused because tegra_dma_global_pause() acquires a lock
but does not release it. However, the lock is released by
tegra_dma_global_resume(). These pause/resume functions are called in
pairs and so it does appear to work.
This global pause is used on early tegra devices that do not have an
individual pause for each channel. The lock appears to be used to ensure
that multiple channels do not attempt to assert/de-assert the global pause
at the same time which could cause the DMA controller to be in the wrong
paused state. Rather than locking around the entire code between the pause
and resume, employ a simple counter to keep track of the global pause
requests. By using a counter, it is only necessary to hold the lock when
pausing and unpausing the DMA controller and hence, fixes the sparse
warning.
Please note that for devices that support individual channel pausing, the
DMA controller lock is not held between pausing and unpausing the channel.
Hence, this change will make the devices that use the global pause behave
in the same way, with regard to locking, as those that don't.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Some void functions have unnecessary return statements at the end
(reported by sparse) and so remove these. Also remove the return variables
from functions tegra_dma_prep_slave_sg() and tegra_dma_prep_slave_cyclic()
because the value is not used.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Everytime a DMA channel register is accessed, the channel base address
is calculated by adding the DMA base address and the channel register
offset. Avoid this calculation and simply calculate the channel base
address once at probe time for each DMA channel.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The callback and callback_param members of the tegra_dma_sg_req structure
are never used. The dma-engine structure, dma_async_tx_descriptor, defines
the same members and these are the ones used by the driver. Therefore,
remove the unused versions from the tegra_dma_sg_req structure.
The half_done member of tegra_dma_channel structure is configured but
never used and so remove it.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
clk_enable() may fail, so we should better check the return value and
propagate it in the case of error.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch adds support for the DMA engine present on Allwinner A10,
A13, A10S and A20 SoCs. This engine has two kinds of channels: normal
and dedicated. The main difference is in the mode of operation;
while a single normal channel may be operating at any given time,
dedicated channels may operate simultaneously provided there is no
overlap of source or destination.
Hardware documentation can be found on A10 User Manual (section 12), A13
User Manual (section 14) and A20 User Manual (section 1.12)
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Due to how async_tx behaves internally, having more XOR channels than
CPUs is actually hurting performance more than it improves it, because
memcpy requests get scheduled on a different channel than the XOR
requests, but async_tx will still wait for the completion of the
memcpy requests before scheduling the XOR requests.
It is in fact more efficient to have at most one channel per CPU,
which this patch implements by limiting the number of channels per
engine, and the number of engines registered depending on the number
of availables CPUs.
Marvell platforms are currently available in one CPU, two CPUs and
four CPUs configurations:
- in the configurations with one CPU, only one channel from one
engine is used.
- in the configurations with two CPUs, only one channel from each
engine is used (they are two XOR engines)
- in the configurations with four CPUs, both channels of both engines
are used.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The only reason why we had dmacap,* properties is because back when
DMA_MEMSET was supported, only one out of the two channels per engine
could do a memset operation. But this is something that the driver
already knows anyway, and since then, the DMA_MEMSET support has been
removed.
The driver is already well aware of what each channel supports and the
one to one mapping between Linux specific implementation details (such
as dmacap,interrupt enabling DMA_INTERRUPT) and DT properties is a
good indication that these DT properties are wrong.
Therefore, this commit simply gets rid of these dmacap,* properties,
they are now ignored, and the driver is responsible for knowing the
capabilities of the hardware with regard to the dmaengine subsystem
expectations.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
When there is only one burst required do not emit loop instructions to
loop exactly once. Emit just the body of the loop.
Signed-off-by: Michal Suchanek <hramrach@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
set_irq_flags is ARM specific with custom flags which have genirq
equivalents. Convert drivers to use the genirq interfaces directly, so we
can kill off set_irq_flags. The translation of flags is as follows:
IRQF_VALID -> !IRQ_NOREQUEST
IRQF_PROBE -> !IRQ_NOPROBE
IRQF_NOAUTOEN -> IRQ_NOAUTOEN
For IRQs managed by an irqdomain, the irqdomain core code handles clearing
and setting IRQ_NOREQUEST already, so there is no need to do this in
.map() functions and we can simply remove the set_irq_flags calls. Some
users also modify IRQ_NOPROBE and this has been maintained although it
is not clear that is really needed. There appears to be a great deal of
blind copy and paste of this code.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: dmaengine@vger.kernel.org
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The new Solo X has more requirements for SDMA events. So it creates
a event mux to remap most of event numbers in GPR (General Purpose
Register). If we want to use SDMA support for those module who do
not get the even number as default, we need to configure GPR first.
Thus this patch adds this support of GPR event remapping configuration
to the SDMA driver.
Signed-off-by: Zidan Wang <zidan.wang@freescale.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In cyclic mode, the round chaining has been broken by the introduction
of at_xdmac_queue_desc(): AT_XDMAC_MBR_UBC_NDE is set for all descriptors
excepted for the last one. at_xdmac_queue_desc() has to be called one
more time to chain the last and the first descriptors.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Fixes: 0d0ee751f7 ("dmaengine: xdmac: Rework the chaining logic")
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Tasklets may have been scheduled as a result of an earlier interrupt
that could still be running. Kill them before unregistering the
device.
Signed-off-by: Alex Smith <alex.smith@imgtec.com>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Cc: dmaengine@vger.kernel.org
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
We must explicitly free the IRQ before the device is unregistered in
case any device interrupt still occurs, so there's no point in using
the managed variations of the IRQ functions. Change to the regular
versions.
Signed-off-by: Alex Smith <alex.smith@imgtec.com>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Cc: dmaengine@vger.kernel.org
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
When scanning for a free DMA channel, the filter function should ensure
that the channel is on the controller that it was requested to be on in
the DT.
Signed-off-by: Alex Smith <alex.smith@imgtec.com>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Cc: dmaengine@vger.kernel.org
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
When the DT requests a specific channel to use it is not necesssary
to scan through all DMA channels in the system. Just return the
requested channel using dma_get_slave_channel().
Signed-off-by: Alex Smith <alex.smith@imgtec.com>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Cc: dmaengine@vger.kernel.org
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
There are a some signedness bugs such as testing for < 0 on unsigned
return values. Additionally there are some cases where functions which
should return NULL on error actually return a PTR_ERR value which can
result in oopses on error. Fix these issues.
Signed-off-by: Alex Smith <alex.smith@imgtec.com>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Cc: dmaengine@vger.kernel.org
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
For some reason the controller does not support 8 byte transfers (but
does support all other powers of 2 up to 128). In this case fall back
to 4 bytes. In addition, fall back to 128 bytes when any larger power
of 2 would be possible within the alignment constraints, as this is
the maximum supported.
It makes no sense to outright reject 8 or >128 bytes just because the
alignment constraints make those the maximum possible size given the
parameters for the transaction. For instance, this can result in a DMA
from/to an 8 byte aligned address failing.
It is perfectly safe to fall back to smaller transfer sizes, the only
consequence is reduced transfer efficiency, which is far better than
not allowing the transfer at all.
Signed-off-by: Alex Smith <alex.smith@imgtec.com>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Cc: dmaengine@vger.kernel.org
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Several function prototypes did not match the dmaengine API they were
implementing, resulting in build warnings. Correct these.
Signed-off-by: Alex Smith <alex.smith@imgtec.com>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Cc: dmaengine@vger.kernel.org
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
If DMA interrupt comes and is latched by IRQ controller during the
execution of dma_terminate_all(), dma_irq routine will be executed
after dma terminated, and it will cause kernel panic.
We clear DMA interrupts in dma_terminate_all() to avoid this useless
interrupt.
Signed-off-by: Yanchang Li <Yanchang.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Add support for DMA on NXP LPC18xx/43xx platforms which has
a multiplexer in front of the PL080 dma request lines.
The mux is a single register in the LPC18xx/43xx CREG block
and can multiplex up to 4 request lines to each of the 16
lines on the PL080.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This fixes the following error:
drivers/dma/pxa_dma.c: In function ‘dbg_show_requester_chan’:
drivers/dma/pxa_dma.c:192:2: error: void value not ignored as it ought to be
pos += seq_printf(s, "DMA channel %d requester :\n", phy->idx);
^
drivers/dma/pxa_dma.c:197:8: error: void value not ignored as it ought to be
!!(drcmr & DRCMR_MAPVLD));
^
scripts/Makefile.build:258: recipe for target 'drivers/dma/pxa_dma.o' failed
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch increments privatecnt value and set DMA_PRIVATE in device
caps in dma_request_slave_channel() function. This is needed to keep
privatecnt increment/decrement balance.
As function dma_release_channel() decrements privatecnt counter, we need
to increment it when channel is requested. Otherwise privatecnt drops
into negatives after few dma_release_channel() calls.
Reported-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Don't use the direction passed in the configuration, and rely on each
transfer's direction to prepare the transfers. This will enable
future removal of direction parameter from dma_slave_config.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
IOAT_COMPLETION_PENDING flag was deprecated for v2 and v3 drivers but was
not cleaned up. Doing that now. The commit deprecated this flag was
4dec23d7 ioatdma: fix race between updating ioat->head and
IOAT_COMPLETION_PENDING.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
./scripts/kerne-doc is reporting errors on dma.h. Clean up all reported
errors.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Since we are a "single" device driver now we no longer require the function
pointers in ioatdma_device. Remove.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Moving the relevant functions to their respective .c files and removal of
dma_v3.c file. Also removed various ioat3 references when appropriate.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Move all DMA descriptor prepping functions to prep.c file. Fixup all
broken bits caused by the move.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Moving all the init routines to init.c and fixup anything broken during
the move.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Move and fixup all sysfs related bits to sysfs.c file.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Clean out dma_v2 and remove ioat2 calls since we are moving everything
to just ioat.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Changing the variable names for ioatdma_device to be consistently named
ioat_dma instead of device/dma in order to avoid confusion and distinct
from struct device. This will clearly indicate that it is an
ioatdma_device. This also make all the naming consistent that the dma
device is ioat_dma and all the channels are ioat_chan.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Kill the common ioatdma channel structure and everything that is not
dma_chan to be ioat_dma_chan. Since we don't have to worry about v1
and v2 ioatdma anymore this makes it much cleaner and obvious for
maintenance.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Removal of support for ioatdma v2 device support.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Cleaning up of ioat1 specific code as it is no longer supported
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Removal of any devices that are ioatdma pre-3.0. This is the first step
in attempting to clean up the ioatdma driver and remove hw no longer
supported.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
If the allocation order is 16, then the u16 count will overflow and wrap
to zero when assigned the value 1 << 16.
Change the type of 'total_descs' to int, so that it is large enough to
store a value equal or greater than 1 << 16.
Signed-off-by: Allen Hubbe <Allen.Hubbe@emc.com>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
If the allocation order is 16, then the u16 index will overflow and wrap
to zero instead of being equal or greater than 1 << 16. The loop
condition will always be true, and the loop will run until all the
memory resources are depleted.
Change the type of index 'i' to u32, so that it is large enough to store
a value equal or greater than 1 << 16.
Signed-off-by: Allen Hubbe <Allen.Hubbe@emc.com>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The functions irq_irq_err and ipu_irq_fn are identical plus/minus the
comments. Remove one.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: dmaengine@vger.kernel.org
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The irq argument of most interrupt flow handlers is unused or merily
used instead of a local variable. The handlers which need the irq
argument can retrieve the irq number from the irq descriptor.
Search and update was done with coccinelle and the invaluable help of
Julia Lawall.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: dmaengine@vger.kernel.org
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The XDMAC also supports memset operations over discontiguous areas. Add the
necessary logic to support this.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
DMA will not stop when clearing enable bit till all transaction
is done. The bug is exposed in audio playback because ring DMA
chain never stop. Force hardware to stop with setting FORCE bit.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Align src and dst width to fix data alignment issue as
trailing single transaction that does not fill a full
burst require identical src/dst data width.
Burst length limitation can be addressed well too.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Most drivers need to set constraints on the buffer alignment for async tx
operations. However, even though it is documented, some drivers either use
a defined constant that is not matching what the alignment variable expects
(like DMA_BUSWIDTH_* constants) or fill the alignment in bytes instead of
power of two.
Add a new enum for these alignments that matches what the framework
expects, and convert the drivers to it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
devm_ioremap_resource returns ERR_PTR on failure.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch adds DEV_TO_DEV support for i.MX SDMA driver to support data
transfer between two peripheral FIFOs.
The per_2_per script requires two peripheral addresses and two DMA
requests, and it need to check the src addr and dst addr is in the SPBA
bus space or in the AIPS bus space.
Signed-off-by: Shengjiu Wang <shengjiu.wang@freescale.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
We had a regression due to reuse of descriptor so we have reverted that.
Rest are driver fixes
at_hdmac and at_xdmac for residue, trannfer width, and channel config
pl330 final fix for dma fails and overflow issue
xgene resouce map fix
mv_xor big endian op fix
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=X0jd
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-fix-4.2-rc5' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine fixes from Vinod Koul:
"We had a regression due to reuse of descriptor so we have reverted
that.
The rest are driver fixes:
- at_hdmac and at_xdmac for residue, trannfer width, and channel config
- pl330 final fix for dma fails and overflow issue
- xgene resouce map fix
- mv_xor big endian op fix"
* tag 'dmaengine-fix-4.2-rc5' of git://git.infradead.org/users/vkoul/slave-dma:
Revert "dmaengine: virt-dma: don't always free descriptor upon completion"
dmaengine: mv_xor: fix big endian operation in register mode
dmaengine: xgene-dma: Fix the resource map to handle overlapping
dmaengine: at_xdmac: fix transfer data width in at_xdmac_prep_slave_sg()
dmaengine: at_hdmac: fix residue computation
dmaengine: at_xdmac: fix bug about channel configuration
dmaengine: pl330: Really fix choppy sound because of wrong residue calculation
dmaengine: pl330: Fix overflow when reporting residue in memcpy
This reverts commit b9855f03d5.
The patch break existing DMA usage case. For example, audio SOC
dmaengine never release channel and cause virt-dma to cache too
much memory in descriptor to exhaust system memory.
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Commit 6f166312c6 ("dmaengine: mv_xor: add support for a38x command
in descriptor mode") introduced the support for a feature that
appeared in Armada 38x: specifying the operation to be performed in a
per-descriptor basis rather than globally per channel.
However, when doing so, it changed the function mv_chan_set_mode() to
use:
if (IS_ENABLED(__BIG_ENDIAN))
instead of:
#if defined(__BIG_ENDIAN)
While IS_ENABLED() is perfectly fine for CONFIG_* symbols, it is not
for other symbols such as __BIG_ENDIAN that is provided directly by
the compiler. Consequently, the commit broke support for big-endian,
as the XOR_DESCRIPTOR_SWAP flag was not set in the XOR channel
configuration register.
The primarily visible effect was some nasty warnings and failures
appearing during the self-test of the XOR unit:
[ 1.197368] mv_xor d0060900.xor: error on chan 0. intr cause 0x00000082
[ 1.197393] mv_xor d0060900.xor: config 0x00008440
[ 1.197410] mv_xor d0060900.xor: activation 0x00000000
[ 1.197427] mv_xor d0060900.xor: intr cause 0x00000082
[ 1.197443] mv_xor d0060900.xor: intr mask 0x000003f7
[ 1.197460] mv_xor d0060900.xor: error cause 0x00000000
[ 1.197477] mv_xor d0060900.xor: error addr 0x00000000
[ 1.197491] ------------[ cut here ]------------
[ 1.197513] WARNING: CPU: 0 PID: 1 at ../drivers/dma/mv_xor.c:664 mv_xor_interrupt_handler+0x14c/0x170()
See also:
http://storage.kernelci.org/next/next-20150617/arm-mvebu_v7_defconfig+CONFIG_CPU_BIG_ENDIAN=y/lab-khilman/boot-armada-xp-openblocks-ax3-4.txt
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Fixes: 6f166312c6 ("dmaengine: mv_xor: add support for a38x command in descriptor mode")
Reviewed-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
There is an overlap in dma ring cmd csr region due to sharing of ethernet
ring cmd csr region. This patch fix the resource overlapping by mapping
the entire dma ring cmd csr region.
Signed-off-by: Rameshwar Prasad Sahu <rsahu@apm.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch adds the missing update of the transfer data width in
at_xdmac_prep_slave_sg().
Indeed, for each item in the scatter-gather list, we check whether the
transfer length is aligned with the data width provided by
dmaengine_slave_config(). If so, we directly use this data width for the
current part of the transfer we are preparing. Otherwise, the data width
is reduced to 8 bits (1 byte). Of course, the actual number of register
accesses must also be updated to match the new data width.
So one chunk was missing in the original patch (see Fixes tag below): the
number of register accesses was correctly set to (len >> fixed_dwidth) in
mbr_ubc but the real data width was not updated in mbr_cfg. Since mbr_cfg
may change for each part of the scatter-gather transfer this also explains
why the original patch used the Descriptor View 2 instead of the
Descriptor View 1.
Let's take the example of a DMA transfer to write 8bit data into an Atmel
USART with FIFOs. When FIFOs are enabled in the USART, its Transmit
Holding Register (THR) works in multidata mode, that is to say that up to
4 8bit data can be written into the THR in a single 32bit access and it is
still possible to write only one data with a 8bit access. To take
advantage of this new feature, the DMA driver was modified to allow
multiple dwidths when doing slave transfers.
For instance, when the total length is 22 bytes, the USART driver splits
the transfer into 2 parts:
First part: 20 bytes transferred through 5 32bit writes into THR
Second part: 2 bytes transferred though 2 8bit writes into THR
For the second part, the data width was first set to 4_BYTES by the USART
driver thanks to dmaengine_slave_config() then at_xdmac_prep_slave_sg()
reduces this data width to 1_BYTE because the 2 byte length is not aligned
with the original 4_BYTES data width. Since the data width is modified,
the actual number of writes into THR must be set accordingly.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Fixes: 6d3a7d9e3a ("dmaengine: at_xdmac: allow muliple dwidths when doing slave transfers")
Cc: stable@vger.kernel.org #4.0 and later
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
As claimed by the programmer datasheet and confirmed by the IP designer,
the Block Transfer Size (BTSIZE) bitfield of the Channel x Control A
Register (CTRLAx) always refers to a number of Source Width (SRC_WIDTH)
transfers.
Both the SRC_WIDTH and BTSIZE bitfields can be extacted from the CTRLAx
register to compute the DMA residue. So the 'tx_width' field is useless
and can be removed from the struct at_desc.
Before this patch, atc_prep_slave_sg() was not consistent: BTSIZE was
correctly initialized according to the SRC_WIDTH but 'tx_width' was always
set to reg_width, which was incorrect for MEM_TO_DEV transfers. It led to
bad DMA residue when 'tx_width' != SRC_WIDTH.
Also the 'tx_width' field was mostly set only in the first and last
descriptors. Depending on the kind of DMA transfer, this field remained
uninitialized for intermediate descriptors. The accurate DMA residue was
computed only when the currently processed descriptor was the first or the
last of the chain. This algorithm was a little bit odd. An accurate DMA
residue can always be computed using the SRC_WIDTH and BTSIZE bitfields
in the CTRLAx register.
Finally, the test to check whether the currently processed descriptor is
the last of the chain was wrong: for cyclic transfer, last_desc->lli.dscr
is NOT equal to zero, since set_desc_eol() is never called, but logically
equal to first_desc->txd.phys. This bug has a side effect on the
drivers/tty/serial/atmel_serial.c driver, which uses cyclic DMA transfer
to receive data. Since the DMA residue was wrong each time the DMA
transfer reaches the second (and last) period of the transfer, no more
data were received by the USART driver till the cyclic DMA transfer loops
back to the first period.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: Torsten Fleischer <torfl6749@gmail.com>
Tested-by: Jirí Prchal <jiri.prchal@aksignal.cz>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
When using descriptor view 2 or higher, we don't write the configuration
into AT_XDMAC_CC register because this configuration will be fetch from
the descriptor. Unfortunately, the PROT bit is not updated with this
method, we have to do it manually before enabling the channel.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Intel integrated DMA (iDMA) 64-bit is a specific IP that is used as a part of
LPSS devices such as HSUART or SPI. The iDMA IP is attached for private
usage on each host controller independently.
While it has similarities with Synopsys DesignWare DMA, the following
distinctions doesn't allow to use the existing driver:
- 64-bit mode with corresponding changes in Hardware Linked List data structure
- many slight differences in the channel registers
Moreover this driver is based on the DMA virtual channels framework that helps
to make the driver cleaner and easy to understand.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The crossbar for eDMA works exactly the same way as sDMA, but sDMA
requires an offset of 1, while no offset is needed for eDMA.
Based on the patch from Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
CC: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Switch to my kernel.org alias instead of a badly named gmail address,
which I rarely use.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
At device removal, tasklets are not disabled and irqs are still enabled, so
free the irq explicitly on device removal
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Add ZTE ZX296702 dma controller support. Only
device tree probe is support currently.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Reviewed-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Use irq_desc_get_xxx() to avoid redundant lookup of irq_desc while we
already have a pointer to corresponding irq_desc.
This is also a preparation for the removal of the 'irq' argument from
interrupt flow handlers.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: dmaengine@vger.kernel.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Chained irq handlers usually set up handler data as well. We now have
a function to set both under irq_desc->lock. Replace the two calls
with one.
Search and conversion was done with coccinelle.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: dmaengine@vger.kernel.org
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
All hardware accesses are done under virtual channel lock. That's why specific
channel lock is excessive and can be removed safely. This has been tested on
Intel Medfield and Merrifield.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The dmaengine core assumes that async DMA devices will only be removed
when they not used anymore, or it assumes dma_async_device_unregister()
will only be called by dma driver exit routines. But this assumption is
not true for the IOAT driver, which calls dma_async_device_unregister()
from ioat_remove(). So current IOAT driver doesn't support device
hot-removal because it may cause system crash to hot-remove an inuse
IOAT device.
To support CPU socket hot-removal, all PCI devices, including IOAT
devices embedded in the socket, will be hot-removed. The idea solution
is to enhance the dmaengine core and IOAT driver to support hot-removal,
but that's too hard.
This patch implements a hack to disable IOAT devices under hotplug-capable
CPU socket so it won't break socket hot-removal.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This allows claiming of non-RAID channels as a private channel. This
prevents breakage of MDRAID using the IOATDMA channels via
async_tx but also allows agents such as NTB to claim channels
exclusively for its usages.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Removing static analysis error:-
Possible null pointer dereference: xt
Because currently xt is dereferenced before NULL check,
Thus Use it after NULL Check.
Signed-off-by: Maninder Singh <maninder1.s@samsung.com>
Reviewed-by: Vaneet Narang <v.narang@samsung.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
clk_prepare_enable() may fail, so we should better check its return value
and propagate it in the case of error.
While at it, change the label 'err' to a more descriptive naming.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
When pl330 driver was used during sound playback, after some time or
after a number of plays the sound became choppy or totally noisy. For
example on Odroid XU3 board the first four executions of aplay with
small WAVE worked fine, but fifth was unrecognizable with errors:
$ aplay /usr/share/sounds/alsa/Front_Right.wava
underrun!!! (at least 0.095 ms long)
Issue was caused by wrong residue reported by pl330 driver to
pcm_dmaengine for its cyclic dma transfers.
The pl330_tx_status(), residue reporting function, used a "last" flag in
a descriptor to indicate that there is no more data to send.
The pl330_tx_submit() iterated over descriptors trying to remove this
flag from them and then mark last descriptor as "last". However when
iterating it actually removed the flag not from descriptors but always
from last of it (and then reset it). Thus effectively once some
descriptor was marked as last, then it stayed like this forever causing
residue to be reported too low.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Fixes: aee4d1fac8 ("dmaengine: pl330: improve pl330_tx_status() function")
Cc: <stable@vger.kernel.org>
Reported-by: gabriel@unseen.is
Suggested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
During memcpy operations the residue was always set to an u32 overflowed
value.
In pl330_tx_status() function number of currently transferred bytes was
subtracted from internal "bytes_requested" field. However this
"bytes_requested" was not initialized at start to length of memcpy
buffer so transferred bytes were subtracted from 0 causing overflow.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Cc: <stable@vger.kernel.org>
Fixes: aee4d1fac8 ("dmaengine: pl330: improve pl330_tx_status() function")
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Commit 3b62286d0e ("dmaengine: Remove FSF mailing addresses") left Free
Software Foundation mailing address still in two files. Remove it now.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Merge third patchbomb from Andrew Morton:
- the rest of MM
- scripts/gdb updates
- ipc/ updates
- lib/ updates
- MAINTAINERS updates
- various other misc things
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (67 commits)
genalloc: rename of_get_named_gen_pool() to of_gen_pool_get()
genalloc: rename dev_get_gen_pool() to gen_pool_get()
x86: opt into HAVE_COPY_THREAD_TLS, for both 32-bit and 64-bit
MAINTAINERS: add zpool
MAINTAINERS: BCACHE: Kent Overstreet has changed email address
MAINTAINERS: move Jens Osterkamp to CREDITS
MAINTAINERS: remove unused nbd.h pattern
MAINTAINERS: update brcm gpio filename pattern
MAINTAINERS: update brcm dts pattern
MAINTAINERS: update sound soc intel patterns
MAINTAINERS: remove website for paride
MAINTAINERS: update Emulex ocrdma email addresses
bcache: use kvfree() in various places
libcxgbi: use kvfree() in cxgbi_free_big_mem()
target: use kvfree() in session alloc and free
IB/ehca: use kvfree() in ipz_queue_{cd}tor()
drm/nouveau/gem: use kvfree() in u_free()
drm: use kvfree() in drm_free_large()
cxgb4: use kvfree() in t4_free_mem()
cxgb3: use kvfree() in cxgb_free_mem()
...
Main excitement here is Peter Zijlstra's lockless rbtree optimization to
speed module address lookup. He found some abusers of the module lock
doing that too.
A little bit of parameter work here too; including Dan Streetman's breaking
up the big param mutex so writing a parameter can load another module (yeah,
really). Unfortunately that broke the usual suspects, !CONFIG_MODULES and
!CONFIG_SYSFS, so those fixes were appended too.
Cheers,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=tWPQ
-----END PGP SIGNATURE-----
Merge tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull module updates from Rusty Russell:
"Main excitement here is Peter Zijlstra's lockless rbtree optimization
to speed module address lookup. He found some abusers of the module
lock doing that too.
A little bit of parameter work here too; including Dan Streetman's
breaking up the big param mutex so writing a parameter can load
another module (yeah, really). Unfortunately that broke the usual
suspects, !CONFIG_MODULES and !CONFIG_SYSFS, so those fixes were
appended too"
* tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux: (26 commits)
modules: only use mod->param_lock if CONFIG_MODULES
param: fix module param locks when !CONFIG_SYSFS.
rcu: merge fix for Convert ACCESS_ONCE() to READ_ONCE() and WRITE_ONCE()
module: add per-module param_lock
module: make perm const
params: suppress unused variable error, warn once just in case code changes.
modules: clarify CONFIG_MODULE_COMPRESS help, suggest 'N'.
kernel/module.c: avoid ifdefs for sig_enforce declaration
kernel/workqueue.c: remove ifdefs over wq_power_efficient
kernel/params.c: export param_ops_bool_enable_only
kernel/params.c: generalize bool_enable_only
kernel/module.c: use generic module param operaters for sig_enforce
kernel/params: constify struct kernel_param_ops uses
sysfs: tightened sysfs permission checks
module: Rework module_addr_{min,max}
module: Use __module_address() for module_address_lookup()
module: Make the mod_tree stuff conditional on PERF_EVENTS || TRACING
module: Optimize __module_address() using a latched RB-tree
rbtree: Implement generic latch_tree
seqlock: Introduce raw_read_seqcount_latch()
...
To be consistent with other kernel interface namings, rename
of_get_named_gen_pool() to of_gen_pool_get(). In the original function
name "_named" suffix references to a device tree property, which contains
a phandle to a device and the corresponding device driver is assumed to
register a gen_pool object.
Due to a weak relation and to avoid any confusion (e.g. in future
possible scenario if gen_pool objects are named) the suffix is removed.
[sfr@canb.auug.org.au: crypto/marvell/cesa - fix up for of_get_named_gen_pool() rename]
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This time we have support for few new devices, few new features and odd
fixes spread thru the subsystem.
New devices added
- support for CSRatlas7 dma controller
- Allwinner H3(sun8i) controller
- TI DMA crossbar driver on DRA7x
- new pxa driver
New features added:
- memset support is bought back now that we have a user in xdmac controller
- interleaved transfers support different source and destination strides
- supporting DMA routers and configuration thru DT
- support for reusing descriptors
- xdmac memset and interleaved transfer support
- hdmac support for interleaved transfers
- omap-dma support for memcpy
Others
- Constify platform_device_id
- mv_xor fixes and improvements
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=VM4w
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-4.2-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
"This time we have support for few new devices, few new features and
odd fixes spread thru the subsystem.
New devices added:
- support for CSRatlas7 dma controller
- Allwinner H3(sun8i) controller
- TI DMA crossbar driver on DRA7x
- new pxa driver
New features added:
- memset support is bought back now that we have a user in xdmac controller
- interleaved transfers support different source and destination strides
- supporting DMA routers and configuration thru DT
- support for reusing descriptors
- xdmac memset and interleaved transfer support
- hdmac support for interleaved transfers
- omap-dma support for memcpy
Others:
- Constify platform_device_id
- mv_xor fixes and improvements"
* tag 'dmaengine-4.2-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (46 commits)
dmaengine: xgene: fix file permission
dmaengine: fsl-edma: clear pending interrupts on initialization
dmaengine: xdmac: Add memset support
Documentation: dmaengine: document DMA_CTRL_ACK
dmaengine: virt-dma: don't always free descriptor upon completion
dmaengine: Revert "drivers/dma: remove unused support for MEMSET operations"
dmaengine: hdmac: Implement interleaved transfers
dmaengine: Move icg helpers to global header
dmaengine: mv_xor: improve descriptors list handling and reduce locking
dmaengine: mv_xor: Enlarge descriptor pool size
dmaengine: mv_xor: add support for a38x command in descriptor mode
dmaengine: mv_xor: Rename function for consistent naming
dmaengine: mv_xor: bug fix for racing condition in descriptors cleanup
dmaengine: pl330: fix wording in mcbufsz message
dmaengine: sirf: add CSRatlas7 SoC support
dmaengine: xgene-dma: Fix "incorrect type in assignement" warnings
dmaengine: fix kernel-doc documentation
dmaengine: pxa_dma: add support for legacy transition
dmaengine: pxa_dma: add debug information
dmaengine: pxa: add pxa dmaengine driver
...
Here's the tty and serial driver patches for 4.2-rc1.
A number of individual driver updates, some code cleanups, and other
minor things, full details in the shortlog.
All have been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlWNoSAACgkQMUfUDdst+ymxNQCguSEmkAYNDdLyYhdcOqSxJt9u
U1gAoMThUDoomkx6CTDMU1wn53hxgMk9
=eCUS
-----END PGP SIGNATURE-----
Merge tag 'tty-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here's the tty and serial driver patches for 4.2-rc1.
A number of individual driver updates, some code cleanups, and other
minor things, full details in the shortlog.
All have been in linux-next for a while with no reported issues"
* tag 'tty-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (152 commits)
Doc: serial-rs485.txt: update RS485 driver interface
Doc: tty.txt: remove mention of the BKL
MAINTAINERS: tty: add serial docs directory
serial: sprd: check for NULL after calling devm_clk_get
serial: 8250_pci: Correct uartclk for xr17v35x expansion chips
serial: 8250_pci: Add support for 12 port Exar boards
serial: 8250_uniphier: add bindings document for UniPhier UART
serial: core: cleanup in uart_get_baud_rate()
serial: stm32-usart: Add STM32 USART Driver
tty/serial: kill off set_irq_flags usage
tty: move linux/gsmmux.h to uapi
doc: dt: add documentation for nxp,lpc1850-uart
serial: 8250: add LPC18xx/43xx UART driver
serial: 8250_uniphier: add UniPhier serial driver
serial: 8250_dw: support ACPI platforms with integrated DMA engine
serial: of_serial: check the return value of clk_prepare_enable()
serial: of_serial: use devm_clk_get() instead of clk_get()
serial: earlycon: Add support for big-endian MMIO accesses
serial: sirf: use hrtimer for data rx
serial: sirf: correct the fifo empty_bit
...
It was a busy development cycle at this time, as you can see a wide
range of changes in diffstat. There are no big changes but many
refactoring and improvements. Here we go some highlights:
* ALSA core:
- Procfs codes were cleaned up to use seq_file
- Procfs can be opt out via Kconfig (only for EXPERT)
- Two types of jack API were unified finally; now both kctl and input
jack devs are handled via a single function call.
* HD-audio
- Continued code restructuring for the future ASoC driver; now HDA
controller driver is split to a core helper module.
- Preliminary codes for Skylake audio support in HDA core.
- Proper i915 gfx power well management for SKL & co
- Enabled runtime PM as default for Intel HDMI/DP codecs
- Newer Tegra chip supports
- More quirks for Dell headsets, Alienware (with CA0132), etc.
- A couple of DRM ELD helper API functions
* ASoC
- Support for loading ASoC topology maps from firmware, intended to be
used to allow self-describing DSP firmware images to be built which
can map controls added by the DSP to userspace without the kernel
needing to know about individual DSP firmwares
- Lots of refactoring to avoid direct access to snd_soc_codec where
it's not needed supporting future refactoring
- Big refactoring, cleanup and enhancement for the Wolfson ADSP driver
- Cleanup series for TI TAS2552 and R-CAR drivers
- Fixes and improvements on RT56xx codecs
- Support for TI TAS571x power amplifiers
- Support for Qualcomm APQ8016 and ZTE ZX296702 SoCs
- Support for x86 systems with RT5650 and Qualcomm Storm
- Support for Mediatek AFE (Audio Front End) unit
- Other various small fixes to ASoC codec drivers
* Firewire
- Enhanced to allow non-blocking streams to use timestamp
synchronization
- Improve support for DM1500 and BeBoBv3
* Misc
- Cleanup of old pci API functions over all PCI sound drivers
- Fix long-standing regression of the old powermac i2c setup
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=D78E
-----END PGP SIGNATURE-----
Merge tag 'sound-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"It was a busy development cycle at this time, as you can see a wide
range of changes in diffstat. There are no big changes but many
refactoring and improvements. Here we go some highlights:
ALSA core:
- Procfs codes were cleaned up to use seq_file
- Procfs can be opt out via Kconfig (only for EXPERT)
- Two types of jack API were unified finally; now both kctl and input
jack devs are handled via a single function call.
HD-audio:
- Continued code restructuring for the future ASoC driver; now HDA
controller driver is split to a core helper module.
- Preliminary codes for Skylake audio support in HDA core.
- Proper i915 gfx power well management for SKL & co
- Enabled runtime PM as default for Intel HDMI/DP codecs
- Newer Tegra chip supports
- More quirks for Dell headsets, Alienware (with CA0132), etc.
- A couple of DRM ELD helper API functions
ASoC:
- Support for loading ASoC topology maps from firmware, intended to
be used to allow self-describing DSP firmware images to be built
which can map controls added by the DSP to userspace without the
kernel needing to know about individual DSP firmwares
- Lots of refactoring to avoid direct access to snd_soc_codec where
it's not needed supporting future refactoring
- Big refactoring, cleanup and enhancement for the Wolfson ADSP
driver
- Cleanup series for TI TAS2552 and R-CAR drivers
- Fixes and improvements on RT56xx codecs
- Support for TI TAS571x power amplifiers
- Support for Qualcomm APQ8016 and ZTE ZX296702 SoCs
- Support for x86 systems with RT5650 and Qualcomm Storm
- Support for Mediatek AFE (Audio Front End) unit
- Other various small fixes to ASoC codec drivers
Firewire:
- Enhanced to allow non-blocking streams to use timestamp
synchronization
- Improve support for DM1500 and BeBoBv3
Misc:
- Cleanup of old pci API functions over all PCI sound drivers
- Fix long-standing regression of the old powermac i2c setup"
* tag 'sound-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (533 commits)
ALSA: pcm: Fix pcm_class sysfs output
ALSA: hda-beep: Update authors dead email address
ASoC: wm_adsp: Move DSP Rate controls into the codec
ASoC: wm8995: Fix setting sysclk for WM8995_SYSCLK_MCLK2 case
ALSA: hda: provide default bus io ops extended hdac
ALSA: hda: add hda link cleanup routine
ALSA: hda: add hdac_ext stream creation and cleanup routines
ASoC: rsrc-card: remove unused ret
ALSA: HDAC: move SND_HDA_PREALLOC_SIZE to core
ASoC: mediatek: Add machine driver for rt5650 rt5676 codec
ASoC: mediatek: Add machine driver for MAX98090 codec
ASoC: mediatek: Add AFE platform driver
ASoC: rsnd: remove io from rsnd_mod
ASoC: rsnd: move rsnd_mod_is_working() to rsnd_io_is_working()
ASoC: rsnd: don't use rsnd_mod_to_io() on snd_kcontrol
ASoC: rsnd: don't use rsnd_mod_to_io() on rsnd_src_xxx()
ASoC: rsnd: don't use rsnd_mod_to_io() on rsnd_ssi_xxx()
ASoC: rsnd: don't use rsnd_mod_to_io() on rsnd_dma_xxx()
ASoC: rsnd: don't use rsnd_mod_to_io() on rsnd_get_adinr()
ASoC: rsnd: add common interrupt handler for SSI/SRC/DMA
...
Clear pending interrupts before requesting interrupts and move
interrupt initialization after channels have been initialized.
This avoids a NULL pointer dereference panic when using kexec
while DMA requests were running.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The XDMAC supports memset transfers, both over contiguous areas, and over
discontiguous areas through a LLI.
The current memset operation only supports contiguous memset for now, add some
support for it. Scatter-gathered memset will come eventually.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Pull x86 core updates from Ingo Molnar:
"There were so many changes in the x86/asm, x86/apic and x86/mm topics
in this cycle that the topical separation of -tip broke down somewhat -
so the result is a more traditional architecture pull request,
collected into the 'x86/core' topic.
The topics were still maintained separately as far as possible, so
bisectability and conceptual separation should still be pretty good -
but there were a handful of merge points to avoid excessive
dependencies (and conflicts) that would have been poorly tested in the
end.
The next cycle will hopefully be much more quiet (or at least will
have fewer dependencies).
The main changes in this cycle were:
* x86/apic changes, with related IRQ core changes: (Jiang Liu, Thomas
Gleixner)
- This is the second and most intrusive part of changes to the x86
interrupt handling - full conversion to hierarchical interrupt
domains:
[IOAPIC domain] -----
|
[MSI domain] --------[Remapping domain] ----- [ Vector domain ]
| (optional) |
[HPET MSI domain] ----- |
|
[DMAR domain] -----------------------------
|
[Legacy domain] -----------------------------
This now reflects the actual hardware and allowed us to distangle
the domain specific code from the underlying parent domain, which
can be optional in the case of interrupt remapping. It's a clear
separation of functionality and removes quite some duct tape
constructs which plugged the remap code between ioapic/msi/hpet
and the vector management.
- Intel IOMMU IRQ remapping enhancements, to allow direct interrupt
injection into guests (Feng Wu)
* x86/asm changes:
- Tons of cleanups and small speedups, micro-optimizations. This
is in preparation to move a good chunk of the low level entry
code from assembly to C code (Denys Vlasenko, Andy Lutomirski,
Brian Gerst)
- Moved all system entry related code to a new home under
arch/x86/entry/ (Ingo Molnar)
- Removal of the fragile and ugly CFI dwarf debuginfo annotations.
Conversion to C will reintroduce many of them - but meanwhile
they are only getting in the way, and the upstream kernel does
not rely on them (Ingo Molnar)
- NOP handling refinements. (Borislav Petkov)
* x86/mm changes:
- Big PAT and MTRR rework: making the code more robust and
preparing to phase out exposing direct MTRR interfaces to drivers -
in favor of using PAT driven interfaces (Toshi Kani, Luis R
Rodriguez, Borislav Petkov)
- New ioremap_wt()/set_memory_wt() interfaces to support
Write-Through cached memory mappings. This is especially
important for good performance on NVDIMM hardware (Toshi Kani)
* x86/ras changes:
- Add support for deferred errors on AMD (Aravind Gopalakrishnan)
This is an important RAS feature which adds hardware support for
poisoned data. That means roughly that the hardware marks data
which it has detected as corrupted but wasn't able to correct, as
poisoned data and raises an APIC interrupt to signal that in the
form of a deferred error. It is the OS's responsibility then to
take proper recovery action and thus prolonge system lifetime as
far as possible.
- Add support for Intel "Local MCE"s: upcoming CPUs will support
CPU-local MCE interrupts, as opposed to the traditional system-
wide broadcasted MCE interrupts (Ashok Raj)
- Misc cleanups (Borislav Petkov)
* x86/platform changes:
- Intel Atom SoC updates
... and lots of other cleanups, fixlets and other changes - see the
shortlog and the Git log for details"
* 'x86-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (222 commits)
x86/hpet: Use proper hpet device number for MSI allocation
x86/hpet: Check for irq==0 when allocating hpet MSI interrupts
x86/mm/pat, drivers/infiniband/ipath: Use arch_phys_wc_add() and require PAT disabled
x86/mm/pat, drivers/media/ivtv: Use arch_phys_wc_add() and require PAT disabled
x86/platform/intel/baytrail: Add comments about why we disabled HPET on Baytrail
genirq: Prevent crash in irq_move_irq()
genirq: Enhance irq_data_to_desc() to support hierarchy irqdomain
iommu, x86: Properly handle posted interrupts for IOMMU hotplug
iommu, x86: Provide irq_remapping_cap() interface
iommu, x86: Setup Posted-Interrupts capability for Intel iommu
iommu, x86: Add cap_pi_support() to detect VT-d PI capability
iommu, x86: Avoid migrating VT-d posted interrupts
iommu, x86: Save the mode (posted or remapped) of an IRTE
iommu, x86: Implement irq_set_vcpu_affinity for intel_ir_chip
iommu: dmar: Provide helper to copy shared irte fields
iommu: dmar: Extend struct irte for VT-d Posted-Interrupts
iommu: Add new member capability to struct irq_remap_ops
x86/asm/entry/64: Disentangle error_entry/exit gsbase/ebx/usermode code
x86/asm/entry/32: Shorten __audit_syscall_entry() args preparation
x86/asm/entry/32: Explain reloading of registers after __audit_syscall_entry()
...
The big thing this release has been Liam's addition of topology support
to the core. We've also seen quite a bit of driver work and the
continuation of Lars' refactoring for component support.
- Support for loading ASoC topology maps from firmware, intended to be
used to allow self-describing DSP firmware images to be built which
can map controls added by the DSP to userspace without the kernel
needing to know about individual DSP firmwares.
- Lots of refactoring to avoid direct access to snd_soc_codec where
it's not needed supporting future refactoring.
- Big refactoring and cleanup serieses for the Wolfson ADSP and TI
TAS2552 drivers.
- Support for TI TAS571x power amplifiers.
- Support for Qualcomm APQ8016 and ZTE ZX296702 SoCs.
- Support for x86 systems with RT5650 and Qualcomm Storm.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVddV1AAoJECTWi3JdVIfQQQsH/RG3lgOeot5jLWMsxJSKChEl
KI+aaMcOw6Dj2LDccN8i6vUp8q44cKSXIc7lGLOzJW4K+OydCCGAvE+sJGyRE1dd
yOHwcbvjJi4zFlt01RZchJ/Wa/S6zFucl5N9HxWsV4bEtfAA59IuhJLtospUlwsA
mf9mpvSdeUAeh3lM2+AqAbXhTo6dYfD5ky5nrtpAkZjG8gqUG0u8Tpauja0lLcHi
72/3EkzKR6KHaefyPw3LdN+/H/YK79uHCVcctZnQg5xUUymcO16ReoTxKwV9cnDb
lBJ6wO8RpUAO9evoG2Yj/l4p+czDCm5VkHMq0nPklHVRh7s/2PwKfox1aw4Pumg=
=wolq
-----END PGP SIGNATURE-----
Merge tag 'asoc-v4.2' into asoc-next
ASoC: Updates for v4.2
The big thing this release has been Liam's addition of topology support
to the core. We've also seen quite a bit of driver work and the
continuation of Lars' refactoring for component support.
- Support for loading ASoC topology maps from firmware, intended to be
used to allow self-describing DSP firmware images to be built which
can map controls added by the DSP to userspace without the kernel
needing to know about individual DSP firmwares.
- Lots of refactoring to avoid direct access to snd_soc_codec where
it's not needed supporting future refactoring.
- Big refactoring and cleanup serieses for the Wolfson ADSP and TI
TAS2552 drivers.
- Support for TI TAS571x power amplifiers.
- Support for Qualcomm APQ8016 and ZTE ZX296702 SoCs.
- Support for x86 systems with RT5650 and Qualcomm Storm.
# gpg: Signature made Mon 08 Jun 2015 18:48:37 BST using RSA key ID 5D5487D0
# gpg: Oops: keyid_from_fingerprint: no pubkey
# gpg: Good signature from "Mark Brown <broonie@sirena.org.uk>"
# gpg: aka "Mark Brown <broonie@debian.org>"
# gpg: aka "Mark Brown <broonie@kernel.org>"
# gpg: aka "Mark Brown <broonie@tardis.ed.ac.uk>"
# gpg: aka "Mark Brown <broonie@linaro.org>"
# gpg: aka "Mark Brown <Mark.Brown@linaro.org>"
This patch attempts to enhance the case of a transfer submitted multiple
times, and where the cost of creating the descriptors chain is not
negligible.
This happens with big video buffers (several megabytes, ie. several
thousands of linked descriptors in one scatter-gather list). In these
cases, a video driver would want to do :
- tx = dmaengine_prep_slave_sg()
- dma_engine_submit(tx);
- dma_async_issue_pending()
- wait for video completion
- read video data (or not, skipping a frame is also possible)
- dma_engine_submit(tx)
=> here, the descriptors chain recalculation will take time
=> the dma coherent allocation over and over might create holes in
the dma pool, which is counter-productive.
- dma_async_issue_pending()
- etc ...
In order to cope with this case, virt-dma is modified to prevent freeing
the descriptors upon completion if DMA_CTRL_ACK flag is set in the
transfer.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This reverts commit 48a9db462d.
Some platforms actually need support for the memset operations. Bring it back.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The AT91 HDMAC controller supports interleaved transfers through what's
called the Picture-in-Picture mode, which allows to transfer a squared
portion of a framebuffer.
This means that this interleaved transfer only supports interleaved
transfers which have a transfer size and ICGs that are fixed across all the
chunks.
While this is a quite drastic restriction of the interleaved transfers
compared to what the dmaengine API allows, this is still useful, and our
driver will only reject transfers that do not conform to this.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Now that we can have ICGs set for both the source and destination (using
the icg field of struct data_chunk) or for only the source or the
destination (using the dst_icg or src_icg respectively), and that these
fields can be ignored depending on other parameters (src_inc, src_sgl,
etc.), the logic to get the actual ICG value can be quite tricky.
The XDMAC driver was already implementing it, but since we will need it in
other drivers, we can move it to the main header file.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Some drivers implement only pause operation (no resuming). Example is
pl330 where pause is needed for getting residuum. pl330 does not support
resume operation, transfer must be stopped after pause.
However for slaves this is exposed always as "pause and resume" which
introduces subtle errors on Odroid U3 board (Exynos4412 with pl330).
After adding pause function to pl330 driver the audio playback
(utilizing DMA) gets choppy after some time (approximately 24 hours).
Fix this by exposing "cmd_pause" if and only if pause and resume are
implemented.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reported-by: gabriel@unseen.is
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: <stable@vger.kernel.org>
Fixes: 88987d2c75 ("dmaengine: pl330: add DMA_PAUSE feature")
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch change the way free descriptors are marked.
Instead of having a field for descriptor in use, all the descriptors in the
all_slots list are free for use.
This simplify the allocation method and reduce the locking needed.
Signed-off-by: Lior Amsalem <alior@marvell.com>
Reviewed-by: Ofer Heifetz <oferh@marvell.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Now that we have 2 channels assigned to 2 CPUs and all requests are chained
on same channels, we need much more descriptors available to satisfy
async_tx workload.
3072 descriptors was found in our lab as the number of descriptors which
allow the async_tx stack to work without waiting for free descriptors on
submission of new requests.
Signed-off-by: Lior Amsalem <alior@marvell.com>
Reviewed-by: Nadav Haklai <nadavh@marvell.com>
Tested-by: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The Marvell Armada 38x SoC introduce new features to the XOR engine,
especially the fact that the engine mode (MEMCPY/XOR/PQ/etc) can be part of
the descriptor and not set through the controller registers.
This new feature allows mixing of different commands (even PQ) on the same
channel/chain without the need to stop the engine to reconfigure the engine
mode.
Refactor the driver to be able to use that new feature on the Armada 38x,
while keeping the old behaviour on the older SoCs.
Signed-off-by: Lior Amsalem <alior@marvell.com>
Reviewed-by: Ofer Heifetz <oferh@marvell.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The current function names isn't very consistent, and functions with the
same prefix might operate on either a channel or a descriptor, which is
kind of confusing.
Rename these functions to have a consistent and clearer naming scheme.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch fixes a bug in the XOR driver where the cleanup function can be
called and free descriptors that never been processed by the engine (which
result in data errors).
The cleanup function will free descriptors based on the ownership bit in
the descriptors.
Fixes: ff7b04796d ("dmaengine: DMA engine driver for Marvell XOR engine")
Signed-off-by: Lior Amsalem <alior@marvell.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Ofer Heifetz <oferh@marvell.com>
Cc: stable@vger.kernel.org
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This fixes up a merge issue with the amba-pl011.c driver, and we want
the fixes in this branch as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The kernel is not trying to increase mcbufsz. It suggests you should try
doing so. Also print the calculated required size of mcbufsz.
Signed-off-by: Michal Suchanek <hramrach@gmail.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Rework slave configuration part in order to more report wrong errors
about the configuration.
Only maxburst and addr width values are checked when doing the slave
configuration. The validity of the channel configuration is done at
prepare time.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Cc: stable@vger.kernel.org # 4.0 and later
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Using _bh variant for spin locks causes this kind of warning:
Starting logging: ------------[ cut here ]------------
WARNING: CPU: 0 PID: 3 at /ssd_drive/linux/kernel/softirq.c:151
__local_bh_enable_ip+0xe8/0xf4()
Modules linked in:
CPU: 0 PID: 3 Comm: ksoftirqd/0 Not tainted 4.1.0-rc2+ #94
Hardware name: Atmel SAMA5
[<c0013c04>] (unwind_backtrace) from [<c00118a4>] (show_stack+0x10/0x14)
[<c00118a4>] (show_stack) from [<c001bbcc>]
(warn_slowpath_common+0x80/0xac)
[<c001bbcc>] (warn_slowpath_common) from [<c001bc14>]
(warn_slowpath_null+0x1c/0x24)
[<c001bc14>] (warn_slowpath_null) from [<c001e28c>]
(__local_bh_enable_ip+0xe8/0xf4)
[<c001e28c>] (__local_bh_enable_ip) from [<c01fdbd0>]
(at_xdmac_device_terminate_all+0xf4/0x100)
[<c01fdbd0>] (at_xdmac_device_terminate_all) from [<c02221a4>]
(atmel_complete_tx_dma+0x34/0xf4)
[<c02221a4>] (atmel_complete_tx_dma) from [<c01fe4ac>]
(at_xdmac_tasklet+0x14c/0x1ac)
[<c01fe4ac>] (at_xdmac_tasklet) from [<c001de58>]
(tasklet_action+0x68/0xb4)
[<c001de58>] (tasklet_action) from [<c001dfdc>]
(__do_softirq+0xfc/0x238)
[<c001dfdc>] (__do_softirq) from [<c001e140>] (run_ksoftirqd+0x28/0x34)
[<c001e140>] (run_ksoftirqd) from [<c0033a3c>]
(smpboot_thread_fn+0x138/0x18c)
[<c0033a3c>] (smpboot_thread_fn) from [<c0030e7c>] (kthread+0xdc/0xf0)
[<c0030e7c>] (kthread) from [<c000f480>] (ret_from_fork+0x14/0x34)
---[ end trace b57b14a99c1d8812 ]---
It comes from the fact that devices can called some code from the DMA
controller with irq disabled. _bh variant is not intended to be used in
this case since it can enable irqs. Switch to irqsave/irqrestore variant to
avoid this situation.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Cc: stable@vger.kernel.org # 4.0 and later
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
add support for new CSR atlas7 SoC. atlas7 exists V1 and V2 IP.
atlas7 DMAv1 is basically moved from marco, which has never been
delivered to customers and renamed in this patch.
atlas7 DMAv2 supports chain DMA by a chain table, this
patch also adds chain DMA support for atlas7.
atlas7 DMAv1 and DMAv2 co-exist in the same chip. there are some HW
configuration differences(register offset etc.) with old prima2 chips,
so we use compatible string to differentiate old prima2 and new atlas7,
then results in different set in HW for them.
Signed-off-by: Hao Liu <Hao.Liu@csr.com>
Signed-off-by: Yanchang Li <Yanchang.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Nothing in <asm/io.h> uses anything from <linux/vmalloc.h>, so
remove it from there and fix up the resulting build problems
triggered on x86 {64|32}-bit {def|allmod|allno}configs.
The breakages were triggering in places where x86 builds relied
on vmalloc() facilities but did not include <linux/vmalloc.h>
explicitly and relied on the implicit inclusion via <asm/io.h>.
Also add:
- <linux/init.h> to <linux/io.h>
- <asm/pgtable_types> to <asm/io.h>
... which were two other implicit header file dependencies.
Suggested-by: David Miller <davem@davemloft.net>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
[ Tidied up the changelog. ]
Acked-by: David Miller <davem@davemloft.net>
Acked-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Anton Vorontsov <anton@enomsg.org>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Colin Cross <ccross@android.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: James E.J. Bottomley <JBottomley@odin.com>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: K. Y. Srinivasan <kys@microsoft.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Kristen Carlson Accardi <kristen@linux.intel.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Suma Ramars <sramars@cisco.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This patch fixes sparse warnings like incorrect type in assignment
(different base types), cast to restricted __le64.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Rameshwar Prasad Sahu <rsahu@apm.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The vd->node is removed from the lists when the transfer started so the
vchan_get_all_descriptors() will not find it. This results memory leak.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
[andy: fix the typo to prevent a compilation error]
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In order to achieve smooth transition of pxa drivers from old legacy dma
handling to new dmaengine, introduce a function to "hide" dma physical
channels from dmaengine.
This is temporary situation where pxa dma will be handled in 2 places :
- arch/arm/plat-pxa/dma.c
- drivers/dma/pxa_dma.c
The resources, ie. dma channels, will be controlled by pxa_dma. The
legacy code will request or release a channel with
pxad_toggle_reserved_channel().
This is not very pretty, but it ensures both legacy and dmaengine
consumers can live in the same kernel until the conversion is done.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Most code already uses consts for the struct kernel_param_ops,
sweep the kernel for the last offending stragglers. Other than
include/linux/moduleparam.h and kernel/params.c all other changes
were generated with the following Coccinelle SmPL patch. Merge
conflicts between trees can be handled with Coccinelle.
In the future git could get Coccinelle merge support to deal with
patch --> fail --> grammar --> Coccinelle --> new patch conflicts
automatically for us on patches where the grammar is available and
the patch is of high confidence. Consider this a feature request.
Test compiled on x86_64 against:
* allnoconfig
* allmodconfig
* allyesconfig
@ const_found @
identifier ops;
@@
const struct kernel_param_ops ops = {
};
@ const_not_found depends on !const_found @
identifier ops;
@@
-struct kernel_param_ops ops = {
+const struct kernel_param_ops ops = {
};
Generated-by: Coccinelle SmPL
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Junio C Hamano <gitster@pobox.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: cocci@systeme.lip6.fr
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Luis R. Rodriguez <mcgrof@suse.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Reuse the debugging features which were available in pxa architecture.
This is a copy of the code from arch/arm/plat-pxa/dma, which is doomed
to disappear once the conversion is completed towards dmaengine.
This is a transfer of the commit "[ARM] pxa/dma: add debugfs
entries" (d294948c2c).
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This is a new driver for pxa SoCs, which is also compatible with the former
mmp_pdma.
The rationale behind a new driver (as opposed to incremental patching) was :
- the new driver relies on virt-dma, which obsoletes all the internal
structures of mmp_pdma (sw_desc, hw_desc, ...), and by consequence all the
functions
- mmp_pdma allocates dma coherent descriptors containing not only hardware
descriptors but linked list information
The new driver only puts the dma hardware descriptors (ie. 4 u32) into the
dma pool allocated memory. This changes completely the way descriptors are
handled
- the architecture behind the interrupt/tasklet management was rewritten to be
more conforming to virt-dma
- the buffers alignment is handled differently
The former driver assumed that the DMA channel stopped between each
descriptor. The new one chains descriptors to let the channel running. This
is a necessary guarantee for real-time high bandwidth usecases such as video
capture on "old" architectures such as pxa.
- hot chaining / cold chaining / no chaining
Whenever possible, submitting a descriptor "hot chains" it to a running
channel. There is still no guarantee that the descriptor will be issued, as
the channel might be stopped just before the descriptor is submitted. Yet
this allows to submit several video buffers, and resubmit a buffer while
another is under handling.
As before, dma_async_issue_pending() is the only guarantee to have all the
buffers issued.
When an alignment issue is detected (ie. one address in a descriptor is not
a multiple of 8), if the already running channel is in "aligned mode", the
channel will stop, and restarted in "misaligned mode" to finished the issued
list.
- descriptors reusing
A submitted, issued and completed descriptor can be reused, ie resubmitted if
it was prepared with the proper flag (DMA_PREP_ACK). Only a channel
resources release will in this case release that buffer.
This allows a rolling ring of buffers to be reused, where there are several
thousands of hardware descriptors used (video buffer for example).
Additionally, a set of more casual features is introduced :
- debugging traces
- lockless way to know if a descriptor is terminated or not
The driver was tested on zylonite board (pxa3xx) and mioa701 (pxa27x),
with dmatest, pxa_camera and pxamci.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Use the generic mechanism to declare a bitmap instead of unsigned long.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Currently pch pointer is already dereferenced before NULL check
and thus we are getting below warning:
warn: variable dereferenced before check 'pch'
So initialize struct pl330_dmac *pl330 after NULL check
of dma_pl330_chan *pch.
Signed-off-by: Maninder Singh <maninder1.s@samsung.com>
Reviewed-by: Vaneet Narang <v.narang@samsung.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
dma_ts_shift[] isn't used outside this source file. All other users use
the definition from arch/arm/mach-shmobile/dma-register.h.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Current rcar-dmac driver is using spin_lock_irq() / spin_unlock_irq()
in some functions. But, some other driver might call DMAEngine API
during interrupt disabled. In such case, rcar-dmac side spin_unlock_irq()
forcefully allows all interrupts. Therefore, other driver receives
unexpected interruption, and its exclusive access control will be broken.
This patch replaces spin_lock_irq() to spin_lock_irqsave(),
and spin_unlock_irq() to spin_unlock_irqrestore().
Reported-by: Cao Minh Hiep <cm-hiep@jinso.co.jp>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Keita Kobayashi <keita.kobayashi.ym@renesas.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The pl330 device could hang infinitely on certain boards when DMA
channels are terminated.
It was caused by lack of runtime resume when executing
pl330_terminate_all() which calls the _stop() function. _stop() accesses
device register and can loop infinitely while checking for device state.
The hang was confirmed by Dinh Nguyen on Altera SOCFPGA Cyclone V
board during boot. It can be also triggered with:
$ echo 1 > /sys/module/dmatest/parameters/iterations
$ echo dma1chan0 > /sys/module/dmatest/parameters/channel
$ echo 1 > /sys/module/dmatest/parameters/run
$ sleep 1
$ cat /sys/module/dmatest/parameters/run
Reported-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Fixes: ae43b32891 ("ARM: 8202/1: dmaengine: pl330: Add runtime Power Management support v12")
Cc: <stable@vger.kernel.org>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The XDMAC supports interleaved tranfers through its flexible descriptor
configuration.
Add support for that kind of transfers to the dmaengine driver.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
So far, we were setting the NDE bit in our descriptors through some logic to
try to see if we were the last descriptor in the chain.
However, that was turning out to be rather complex to get right, while this
information is also available when we actually chain a new descriptor after an
already existing one.
Simplify this by never setting NDE unless when we actually chain a descriptor.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The code has some logic to compute the burst width according to the alignment
of the address we're using.
Move that in a function of its own to reduce code duplication.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The XDMAC DMA controller uses a concept of views to be able to handle
descriptors of different sizes.
So far, only the views 1 and 2 were handled by the driver. Unfortunately, we
need some of the configuration fields found in the view 3 in order to support
memset and interleaved transfers.
Add the definition for the view 3 registers, and the needed code to handle view
3 descriptors.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The DRA7x has more peripherals with DMA requests than the sDMA can handle:
205 vs 127. All DMA requests are routed through the DMA crossbar, which can
be configured to route selected incoming DMA requests to specific sDMA
request.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Since the mapping between the hardware request lines and channels has been
removed it no longer make sense to have too many channels.
Set the number of channels to match with the number of logical channels
supported by sDMA.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Do not direct map the virtual channels to sDMA request number. When the
sDMA is behind of a crossbar this direct mapping can cause situations when
certain channel can not be requested since the crossbar request number
will no longer match with the sDMA request line.
The direct mapping for virtual channels with HW request lines will make it
harder to implement MEM_TO_MEM mode for the driver.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Use the dma-requests property from DT to get the number of DMA requests.
In case of legacy boot or failure to find the property, use the default
127 as number of requests.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Instead of magic numbers in the code, use define for number of logical DMA
channels and DMA requests.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
DMA routers are transparent devices used to mux DMA requests from
peripherals to DMA controllers. They are used when the SoC integrates more
devices with DMA requests then their controller can handle.
DRA7x is one example of such SoC, where the sDMA can hanlde 128 DMA request
lines, but in SoC level it has 205 DMA requests.
The of_dma_router will be registered as of_dma_controller with special
xlate function and additional parameters. The driver for the router is
responsible to craft the dma_spec (in the of_dma_route_allocate callback)
which can be used to requests a DMA channel from the real DMA controller.
This way the router can be transparent for the system while remaining generic
enough to be used in different environments.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The H3 SoC has the same dma engine as the A31 (sun6i), with a
reduced amount of endpoints and physical channels. Add the proper
config data and compatible string to support it.
Signed-off-by: Jens Kuske <jenskuske@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Removed checkpatch reported spaces in indentation:
ERROR: code indent should use tabs where possible
+^I PL080_CONFIG_TC_IRQ_MASK);$
Signed-off-by: Leonardo Carreras <leocarreras89@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The 8250_omap serial driver relies on dmaengine_pause() actually
pausing the DMA transfer. Before this patch dmaengine_pause() is
a NOP for non-cylic DMA transfers. This allowed the 8250_omap
driver to read DMA buffers while the DMA was still active,
resulting in lost serial data.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The platform_device_id is not modified by the driver and core uses it as
const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The platform_device_id is not modified by the driver and core uses it as
const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The platform_device_id is not modified by the driver and core uses it as
const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The platform_device_id is not modified by the driver and core uses it as
const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The platform_device_id is not modified by the driver and core uses it as
const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The sDMA controller is capable of performing memory copy operation. It need
to be configured to software triggered mode and without HW synchronization.
The sDMA can copy data which is aligned to 8, 16 or 32 bits.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Channels allocated via dma_get_any_slave_channel were not increasing
the counter tracking private allocations. When these channels were
released, privatecnt may erroneously fall to zero. The DMA device
would then lose its DMA_PRIVATE cap and fail to allocate future private
channels (via private_candidate) as any allocations still outstanding
would incorrectly be seen as public allocations.
Signed-off-by: Christopher Freeman <cfreeman@nvidia.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The xgene-dma driver is only useful on X-Gene SoC.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Rameshwar Prasad Sahu <rsahu@apm.com>
Cc: Loc Ho <lho@apm.com>
Cc: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
If CONFIG_PM=n:
drivers/dma/sh/usb-dmac.c:677: warning: ‘usb_dmac_runtime_suspend’ defined but not used
drivers/dma/sh/usb-dmac.c:688: warning: ‘usb_dmac_runtime_resume’ defined but not used
Protect the unused functions by #ifdef CONFIG_PM to fix this.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
HSU_DMA is selected by the HSU_DMA_PCI driver, this should be user selected
so remove the user prompt for this
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
DW_DMAC_CORE is slected by PCI or Platform driver, so this symbol shouldn't
be user selectable, so remove the prompt
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Here's the big tty/serial driver update for 4.1-rc1.
It was delayed for a bit due to some questions surrounding some of the
console command line parsing changes that are in here. There's still
one tiny regression for people who were previously putting multiple
console command lines and expecting them all to be ignored for some odd
reason, but Peter is working on fixing that. If not, I'll send a revert
for the offending patch, but I have faith that Peter can address it.
Other than the console work here, there's the usual serial driver
updates and changes, and a buch of 8250 reworks to try to make that
driver easier to maintain over time, and have it support more devices in
the future.
All of these have been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlU2IcUACgkQMUfUDdst+ylFqACcC8LPhFEZg9aHn0hNUoqGK3rE
5dUAnR4b8r/NYqjVoE9FJZgZfB/TqVi1
=lyN/
-----END PGP SIGNATURE-----
Merge tag 'tty-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial updates from Greg KH:
"Here's the big tty/serial driver update for 4.1-rc1.
It was delayed for a bit due to some questions surrounding some of the
console command line parsing changes that are in here. There's still
one tiny regression for people who were previously putting multiple
console command lines and expecting them all to be ignored for some
odd reason, but Peter is working on fixing that. If not, I'll send a
revert for the offending patch, but I have faith that Peter can
address it.
Other than the console work here, there's the usual serial driver
updates and changes, and a buch of 8250 reworks to try to make that
driver easier to maintain over time, and have it support more devices
in the future.
All of these have been in linux-next for a while"
* tag 'tty-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (119 commits)
n_gsm: Drop unneeded cast on netdev_priv
sc16is7xx: expose RTS inversion in RS-485 mode
serial: 8250_pci: port failed after wakeup from S3
earlycon: 8250: Document kernel command line options
earlycon: 8250: Fix command line regression
earlycon: Fix __earlycon_table stride
tty: clean up the tty time logic a bit
serial: 8250_dw: only get the clock rate in one place
serial: 8250_dw: remove useless ACPI ID check
dmaengine: hsu: move memory allocation to GFP_NOWAIT
dmaengine: hsu: remove redundant pieces of code
serial: 8250_pci: add Intel Tangier support
dmaengine: hsu: add Intel Tangier PCI ID
serial: 8250_pci: replace switch-case by formula for Intel MID
serial: 8250_pci: replace switch-case by formula
tty: cpm_uart: replace CONFIG_8xx by CONFIG_CPM1
serial: jsm: some off by one bugs
serial: xuartps: Fix check in console_setup().
serial: xuartps: Get rid of register access macros.
serial: xuartps: Fix iobase use.
...
This driver uses '#ifdef CONFIG_ARCH_SHMOBILE' and '#ifdef CONFIG_ARM'
interchangeably in its sh_dmae_probe function, which causes a build
warning when building for ARM without also enabling shmobile:
dma/sh/shdmac.c: In function sh_dmae_probe:
dma/sh/shdmac.c:696:6: warning: unused variable errirq [-Wunused-variable]
dma/sh/shdmac.c:695:16: warning: unused variable irqflags [-Wunused-variable]
dma/sh/shdmac.c: At top level:
dma/sh/shdmac.c:447:20: warning: sh_dmae_err defined but not used [-Wunused-function]
This changes all the #ifdef to test for CONFIG_ARCH_SHMOBILE to
avoid that warning. An earlier patch from Laurent had fixed the warning
for non-ARM case, but it still remained present in ARM randconfig builds.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 52d6a5ee10 ("DMA: shdma: Fix warnings due to declared but unused symbols")
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
drivers/dma/xgene-dma.c:2079:3-8: No need to set .owner here. The core will do it.
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
CC: Rameshwar Prasad Sahu <rsahu@apm.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Memory allocated for pch_dma is not deallocated in case of failure
in pch_dma_probe().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The code here is checking for IS_ERR() but devm_ioremap() returns NULL
on error and not an error pointer.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
We put 9 characters into the 8 character name[] array. Let's make the
array bigger and change the sprintf() to snprintf().
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch fixes an issue that the usb_dmac_desc_free() is
dereferencing freed memory 'desc' because it uses list_for_each_entry().
This function should use list_for_each_entry_safe().
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Fix the following warning by initializing necessary fields in the dma_device
structure.
------------[ cut here ]------------
WARNING: CPU: 0 PID: 1 at drivers/dma/dmaengine.c:863 dma_async_device_register+0x2b4/0x4f0()
this driver doesn't support generic slave capabilities reporting
Modules linked in:
CPU: 0 PID: 1 Comm: swapper Not tainted 4.0.0-rc5+ #10
Hardware name: Sharp-Collie
[<c0105cd8>] (unwind_backtrace) from [<c0103ef8>] (show_stack+0x10/0x14)
[<c0103ef8>] (show_stack) from [<c010e9b8>] (warn_slowpath_common+0x74/0xac)
[<c010e9b8>] (warn_slowpath_common) from [<c010ea20>] (warn_slowpath_fmt+0x30/0x40)
[<c010ea20>] (warn_slowpath_fmt) from [<c02956fc>] (dma_async_device_register+0x2b4/0x4f0)
[<c02956fc>] (dma_async_device_register) from [<c0296a9c>] (sa11x0_dma_probe+0x21c/0x358)
[<c0296a9c>] (sa11x0_dma_probe) from [<c02c52c0>] (platform_drv_probe+0x30/0x94)
[<c02c52c0>] (platform_drv_probe) from [<c02c39bc>] (driver_probe_device+0x84/0x234)
[<c02c39bc>] (driver_probe_device) from [<c02c3c4c>] (__driver_attach+0x98/0x9c)
[<c02c3c4c>] (__driver_attach) from [<c02c1f9c>] (bus_for_each_dev+0x74/0xa4)
[<c02c1f9c>] (bus_for_each_dev) from [<c02c3230>] (bus_add_driver+0x13c/0x1e8)
[<c02c3230>] (bus_add_driver) from [<c02c4260>] (driver_register+0x78/0xf8)
[<c02c4260>] (driver_register) from [<c0100624>] (do_one_initcall+0x84/0x1f4)
[<c0100624>] (do_one_initcall) from [<c0700e1c>] (kernel_init_freeable+0xf8/0x1b4)
[<c0700e1c>] (kernel_init_freeable) from [<c040a920>] (kernel_init+0x8/0xf0)
[<c040a920>] (kernel_init) from [<c01013a8>] (ret_from_fork+0x14/0x2c)
---[ end trace e188b8fe0e782e75 ]---
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
There have been major modernization with the standard bus: in ALSA
sequencer core and HD-audio. Also, HD-audio receives the regmap
support replacing the in-house cache register cache code. These
changes shouldn't impact the existing behavior, but rather
refactoring.
In addition, HD-audio got the code split to a core library part and
the "legacy" driver parts. This is a preliminary work for adapting
the upcoming ASoC HD-audio driver, and the whole transition is still
work in progress, likely finished in 4.1.
Along with them, there are many updates in ASoC area as usual, too:
lots of cleanups, Intel code shuffling, etc.
Here are some highlights:
ALSA core:
- PCM: the audio timestamp / wallclock enhancement
- PCM: fixes in DPCM management
- Fixes / cleanups of user-space control element management
- Sequencer: modernization using the standard bus
HD-audio:
- Modernization using the standard bus
- Regmap support
- Use standard runtime PM for codec power saving
- Widget-path based power-saving for IDT, VIA and Realtek codecs
- Reorganized sysfs entries for each codec object
- More Dell headset support
ASoC:
- Move of jack registration to the card level
- Lots of ASoC cleanups, mainly moving things from the CODEC level
to the card level
- Support for DAPM routes specified by both the machine driver and DT
- Continuing improvements to rcar
- pcm512x enhacements
- Intel platforms updates
- rt5670 updates / fixes
- New platforms / devices: some non-DSP Qualcomm platforms, Google's
Storm platform, Maxmim MAX98925 CODECs and the Ingenic JZ4780 SoC
Misc:
- ice1724: Improved ESI W192M support
- emu10k1: Emu 1010 fixes/enhancement
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=4z5j
-----END PGP SIGNATURE-----
Merge tag 'sound-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"There have been major modernization with the standard bus: in ALSA
sequencer core and HD-audio. Also, HD-audio receives the regmap
support replacing the in-house cache register cache code. These
changes shouldn't impact the existing behavior, but rather
refactoring.
In addition, HD-audio got the code split to a core library part and
the "legacy" driver parts. This is a preliminary work for adapting
the upcoming ASoC HD-audio driver, and the whole transition is still
work in progress, likely finished in 4.1.
Along with them, there are many updates in ASoC area as usual, too:
lots of cleanups, Intel code shuffling, etc.
Here are some highlights:
ALSA core:
- PCM: the audio timestamp / wallclock enhancement
- PCM: fixes in DPCM management
- Fixes / cleanups of user-space control element management
- Sequencer: modernization using the standard bus
HD-audio:
- Modernization using the standard bus
- Regmap support
- Use standard runtime PM for codec power saving
- Widget-path based power-saving for IDT, VIA and Realtek codecs
- Reorganized sysfs entries for each codec object
- More Dell headset support
ASoC:
- Move of jack registration to the card level
- Lots of ASoC cleanups, mainly moving things from the CODEC level to
the card level
- Support for DAPM routes specified by both the machine driver and DT
- Continuing improvements to rcar
- pcm512x enhacements
- Intel platforms updates
- rt5670 updates / fixes
- New platforms / devices: some non-DSP Qualcomm platforms, Google's
Storm platform, Maxmim MAX98925 CODECs and the Ingenic JZ4780 SoC
Misc:
- ice1724: Improved ESI W192M support
- emu10k1: Emu 1010 fixes/enhancement"
* tag 'sound-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (411 commits)
ALSA: hda - set GET bit when adding a vendor verb to the codec regmap
ALSA: hda/realtek - Enable the ALC292 dock fixup on the Thinkpad T450
ALSA: hda - Fix another race in runtime PM refcounting
ALSA: hda - Expose codec type sysfs
ALSA: ctl: fix to handle several elements added by one operation for userspace element
ASoC: Intel: fix array_size.cocci warnings
ASoC: n810: Automatically disconnect non-connected pins
ASoC: n810: Consistently pass the card DAPM context to n810_ext_control()
ASoC: davinci-evm: Use card DAPM context to access widgets
ASoC: mop500_ab8500: Use card DAPM context to access widgets
ASoC: wm1133-ev1: Use card DAPM context to access widgets
ASoC: atmel: Improve machine driver compile test coverage
ASoC: atmel: Add dependency to SND_SOC_I2C_AND_SPI where necessary
ALSA: control: Fix a typo of SNDRV_CTL_ELEM_ACCESS_TLV_* with SNDRV_CTL_TLV_OP_*
ALSA: usb-audio: Don't attempt to get Microsoft Lifecam Cinema sample rate
ASoC: rnsd: fix build regression without CONFIG_OF
ALSA: emu10k1: add toggles for E-mu 1010 optical ports
ALSA: ctl: fill identical information to return value when adding userspace elements
ALSA: ctl: fix a bug to return no identical information in info operation for userspace controls
ALSA: ctl: confirm to return all identical information in 'activate' event
...
Here's the big staging driver patchset for 4.1-rc1.
There's a lot of patches here, the Outreachy application period happened
during this development cycle, so that means that there was a lot of
cleanup patches accepted. Other than the normal coding style and sparse
fixes here, there are some driver updates and work toward making some of
the drivers into "mergable" shape (like the Unisys drivers.)
All of these have been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlUsIA0ACgkQMUfUDdst+ylHuACgm8QZ9S6lk45/Qd9YeR3NSDaS
upoAn3gVAaHnuxkW3anivuwOcirgCp3l
=7VHU
-----END PGP SIGNATURE-----
Merge tag 'staging-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver updates from Greg KH:
"Here's the big staging driver patchset for 4.1-rc1.
There's a lot of patches here, the Outreachy application period
happened during this development cycle, so that means that there was a
lot of cleanup patches accepted. Other than the normal coding style
and sparse fixes here, there are some driver updates and work toward
making some of the drivers into "mergable" shape (like the Unisys
drivers.)
All of these have been in linux-next for a while"
* tag 'staging-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (1214 commits)
staging: lustre: orthography & coding style
staging: lustre: lnet: lnet: fix error return code
staging: lustre: fix sparse warning
Revert "Staging: sm750fb: Fix C99 Comments"
Staging: rtl8192u: use correct array for debug output
staging: rtl8192e: Remove dead code
staging: rtl8192e: Comment cleanup (style/format)
staging: rtl8192e: Fix indentation in rtllib_rx_auth_resp()
staging: rtl8192e: Decrease nesting of rtllib_rx_auth_resp()
staging: rtl8192e: Divide rtllib_rx_auth()
staging: rtl8192e: Fix PRINTK_WITHOUT_KERN_LEVEL warnings
staging: rtl8192e: Fix DO_WHILE_MACRO_WITH_TRAILING_SEMICOLON warning
staging: rtl8192e: Fix BRACES warning
staging: rtl8192e: Fix LINE_CONTINUATIONS warning
staging: rtl8192e: Fix UNNECESSARY_PARENTHESES warnings
staging: rtl8192e: remove unused EXPORT_SYMBOL_RSL macro
staging: rtl8192e: Fix RETURN_VOID warnings
staging: rtl8192e: Fix UNNECESSARY_ELSE warning
staging: rtl8723au: Remove unneeded comments
staging: rtl8723au: Use __func__ in trace logs
...
Only one framework update this time around, a change from Lars-Peter to
move full to pm_ops and remove the legacy bus PM ops. Otherwise it's
all driver updates:
- Make the spidev driver complain loudly if registered as spidev with
DT rather than with a compatible string, hopefully helping people
avoid making that mistake.
- Error handling and robustness fixes for the Designware and Intel MID
drivers from Andy Shevchenko.
- Substantial performance improvements for the Raspberry Pi driver from
Martin Sperl.
- Several new features for spidev_test from Adrian Remonda and Ian
Abbott.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVK8JoAAoJECTWi3JdVIfQEl0H/iQU06k/sFtfQYwsj/LJHKTe
L3SOfBoEuS3l9UudCpVspGwikcrbdTtziO/VY0oCPMdjovHrXFsaoT902LGeDsTn
oSnxXojSQOpet7at2tEYk7O/tdyykKR6fU2t4GJBYRreBvvQCG8xsrrAk/ahHTsn
LC4x49zwgvm4R24VPA37AhdDvBUxFWuJC3uQhf9cc59/DqPKaC5cm2L6mA6m5Vwk
W7t6kodr8wURp+Yc+VAvR3u4tRkCJUmgSO54ysGNuToR5brRTyEnBCed2GcqoDjQ
OFQDgHuEP/YPQOojxGJ+RMW5VpKXmaXYotvUhTdLRSevVmVNQfa4zUPtTnb13kA=
=+TxD
-----END PGP SIGNATURE-----
Merge tag 'spi-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"Only one framework update this time around, a change from Lars-Peter
to move full to pm_ops and remove the legacy bus PM ops. Otherwise
it's all driver updates:
- make the spidev driver complain loudly if registered as spidev with
DT rather than with a compatible string, hopefully helping people
avoid making that mistake.
- error handling and robustness fixes for the Designware and Intel
MID drivers from Andy Shevchenko.
- substantial performance improvements for the Raspberry Pi driver
from Martin Sperl.
- several new features for spidev_test from Adrian Remonda and Ian
Abbott"
* tag 'spi-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (75 commits)
spi: bcm2835: enabling polling mode for transfers shorter than 30us
spi: bcm2835: transform native-cs to gpio-cs on first spi_setup
spi: img-spfi: Control CS lines with GPIO
spi: img-spfi: Reset controller after each message
spi: img-spfi: Implement a handle_err() callback
spi: img-spfi: Setup TRANSACTION register before CONTROL register
spi: Make master->handle_err() callback optional to avoid crashes
spi: img-spfi: Limit bit clock to 1/4th of input clock
spi: img-spfi: Implement a prepare_message() callback
spi: fsl-dspi: Add ~50ns delay between cs and sck
spi: fsl-dspi: Add cs-sck delays
spi: fsl-dspi: Fix clock rate scale values
spi: signedness bug in qspi_trigger_transfer_out_int()
spi: imx: read back the RX/TX watermark levels earlier
spi: spi-bfin5xx: Initialize cr_width in bfin_spi_pump_transfers()
spi: bitbang: only toggle bitchanges
spi: pxa2xx: missing break in pxa2xx_ssp_get_clk_div()
spi: fsl-dspi: Fix clock rate scale values
spi: Using Trigger number to transmit/receive data
spi: bcm2835: fill FIFO before enabling interrupts to reduce interrupts/message
...
This reverts commit ecc19d1786.
It added a new warning to try to encourage driver writers to set the
device capabities properly, but drivers haven't been updated and in the
meantime it just generaters a scary message that users cannot actually
do anything about.
Warnings like these are appropriate if you actually expect to fix the
code that causes them. They are not appropriate for releases.
Requested-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add missing directions, residue_granularity,
srd_addr_widths and dst_addr_widths bitfields.
Without those we will see a kernel WARN()
when loading musb on am335x devices.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
We want those fixes (iio primarily) into the -next branch to help with
merge and testing issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The RaidEngine is a new FSL hardware used for Raid5/6 acceration.
This patch enables the RaidEngine functionality and provides
hardware offloading capability for memcpy, xor and pq computation.
It works with async_tx.
Signed-off-by: Harninder Rai <harninder.rai@freescale.com>
Signed-off-by: Xuelin Shi <xuelin.shi@freescale.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This DMAC is Renesas USB high-speed module DMA controller that
supports slave transfer.
This USB-DMAC has similar register sets with R-Car Gen2 DMAC, but
the USB-DMAC has specific registers to control the USB transactions.
If this code is added into the rcar-dmac driver, it will become
unreadable. So, this driver is independent from the rcar-dmac.
And, this USB-DMAC uses virt-dma infrastructure.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The "data" parameter passed indirectly to the edma_callback() should be
edma_chan and not the dma_chan.
This bug was so far harmless since the offset of struct dma_chan within struct
edma_chan is 0. However as soon as someone changes struct edma_chan this would
cause troubles.
Signed-off-by: Petr Kulhavy <petr@barix.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The function d40_prep_sg takes the type enum dma_transfer_direction
as second last parameter. However, the memcpy calls pass DMA_NONE
which is of type enum dma_data_direction. Fix this by passing the
actual transfer direction DMA_MEM_TO_MEM.
This does not change the actual code flow since only the transfer
direction DMA_MEM_TO_DEV and DMA_DEV_TO_MEM are actually used in the
function d40_prep_sg.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch adds a driver for the DMA controller found in the Ingenic
JZ4780.
It currently does not implement any support for the programmable firmware
feature of the controller - this is not necessary for most uses. It also
does not take priority into account when allocating channels, it just
allocates the first available channel. This can be implemented later.
Signed-off-by: Alex Smith <alex.smith@imgtec.com>
Signed-off-by: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
[Updated for dmaengine api changes, Add residue support, couple of minor fixes]
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The vd->node is removed from the lists when the transfer started so the
vchan_get_all_descriptors() will not find it. This results memory leak.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The vd->node is removed from the lists when the transfer started so the
vchan_get_all_descriptors() will not find it. This results memory leak.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In omap_dma_start_desc the vdesc->node is removed from the virt-dma
framework managed lists (to be precise from the desc_issued list).
If a terminate_all comes before the transfer finishes the omap_desc will
not be freed up because it is not in any of the lists and we stopped the
DMA channel so the transfer will not going to complete.
There is no special sequence for leaking memory when using cyclic (audio)
transfer: with every start and stop of a cyclic transfer the driver leaks
struct omap_desc worth of memory.
Free up the allocated memory directly in omap_dma_terminate_all() since the
framework will not going to do that for us.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
CC: <stable@vger.kernel.org>
CC: <linux-omap@vger.kernel.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
If edma_terminate_all() was called while a transfer was running (i.e. after
edma_execute() but before edma_callback()) the echan->edesc was not freed.
This was due to the fact that a running transfer is on none of the
vchan lists: desc_submitted, desc_issued, desc_completed (edma_execute()
removes it from the desc_issued list), so the vchan_dma_desc_free_list()
called at the end of edma_terminate_all() didn't find it and didn't free it.
This bug was found on an AM1808 based hardware (very similar to da850evm,
however using the second MMC/SD controller), where intense operations on the SD
card wasted the device 128MB RAM within a couple of days.
Peter Ujfalusi:
The issue is even more severe since it affects cyclic (audio) transfers as
well. In this case starting/stopping audio will results memory leak.
Signed-off-by: Petr Kulhavy <petr@barix.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
CC: <stable@vger.kernel.org>
CC: <linux-omap@vger.kernel.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Setup the capabilities of the device/driver, so that users of the DMAengine API
can query them.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The GFP_ATOMIC is too strict, and DMAEngine documentation make an advice to use
GFP_NOWAIT. This patch does the conversion.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are few places where the implemented pieces of code are not needed, i.e.:
- direction can't be wrong in hsu_dma_chan_start()
- desc->active set to 0 by kzalloc
- DMAEngine is NULL-aware when call ->device_alloc_chan_resources()
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Intel Tangier is known to have the HSU DMA IP as PCI device 00:05.0. The patch
adds the ID as found on Intel Edison board to the PCI device table.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We want the staging tree fixes that are upstream here as well to prevent
merge conflicts from people trying to clean up code.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that device_alloc_chan_resources handler in not mandatory, remove dummy
implementations
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Now that device_alloc_chan_resources handler in not mandatory, remove dummy
implementations
Acked-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Now that device_alloc_chan_resources handler in not mandatory, remove dummy
implementations
Acked-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Now that device_alloc_chan_resources handler in not mandatory, remove dummy
implementations
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Now that device_alloc_chan_resources handler in not mandatory, remove dummy
implementations
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The pl330_tx_status() function returns the desc->status if the
dma_cookie_status() call does indicate the cookie completed,
however the desc->status is not look directly compatible. Sparse
throws the following warning:
pl330.c:2262:35: warning: mixing different enum types
pl330.c:2262:35: int enum desc_status versus
pl330.c:2262:35: int enum dma_status
Attempt to fix this by adding a switch statement to turn the
desc->status into a dma_status.
Note, this has only been tested with the dmatest suite.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
--
Vinod Koul <vinod.koul@intel.com>
Dan Williams <dan.j.williams@intel.com>
DMA List <dmaengine@vger.kernel.org>
Maxime Ripard <maxime.ripard@free-electrons.com>
Jassi Brar <jassisinghbrar@gmail.com>
Liviu Dudau <Liviu.Dudau@arm.com>
Linux ARM Kernel <linux-arm-kernel@lists.infradead.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Whilst running sparse on pl330 driver it was noticed there are
two functions that are not static but not exported to any other
users in the kernel.
Fix the following warnings by making 'pl330_pause' and the
'pl330_get_current_xferred_count' static:
pl330.c:2165:5: warning: symbol 'pl330_pause' was not declared. Should it be static?
pl330.c:2206:5: warning: symbol 'pl330_get_current_xferred_count' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
--
Vinod Koul <vinod.koul@intel.com>
Dan Williams <dan.j.williams@intel.com>
DMA List <dmaengine@vger.kernel.org>
Maxime Ripard <maxime.ripard@free-electrons.com>
Jassi Brar <jassisinghbrar@gmail.com>
Liviu Dudau <Liviu.Dudau@arm.com>
Linux ARM Kernel <linux-arm-kernel@lists.infradead.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
When running Xilinx Zynq in big-endian mode the pl330 driver
fails to pass the dmatest suite. To fix this, ensure all non
byte values are written in little endian.
As a note, the documentation does not mention if it will do
big-endian descriptor fetches, only that it will swap the
data in flight.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
--
Vinod Koul <vinod.koul@intel.com>
Dan Williams <dan.j.williams@intel.com>
DMA List <dmaengine@vger.kernel.org>
Maxime Ripard <maxime.ripard@free-electrons.com>
Jassi Brar <jassisinghbrar@gmail.com>
Liviu Dudau <Liviu.Dudau@arm.com>
Linux ARM Kernel <linux-arm-kernel@lists.infradead.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Ensure that clients can automatically configure themselves and avoid a
nasty warning at boot by providing capability information.
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Renesas R-Car sound (= rsnd) needs 2 DMAC which are called as
Audio DMAC (= 1st DMAC) and Audio DMAC peri peri (2nd DMAC).
And rsnd had assumed that 1st / 2nd DMACs are implemented as DMAEngine.
But, in result of DMA ML discussion, 2nd DMAC was concluded that it is
not a general purpose DMAC (2nd DMAC is for Device to Device inside
sound system). Additionally, current DMAEngine can't support Device to
Device, and we don't have correct DT bindings for it at this point.
So the easiest solution for it is that move it from DMAEngine to rsnd
driver.
Audio DMAC peri peri on DMAEngine is no longer needed. remove it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Currently when version 3.1 of the mx6q SDMA firmware is used we get:
[ 0.392169] imx-sdma 20ec000.sdma: unknown firmware version
[ 0.399281] imx-sdma 20ec000.sdma: initialized
Add support for it.
Based on a patch from Shengjiu Wang from the internal FSL kernel.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Since the last and the only user of this driver is converted to use dw_dmac we
can remove driver from the tree.
Moreover, besides the driver is unmaintained a long time, it serves for the
DesignWare DMA IP, for which we have already driver in the tree.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch moves the xilinx_dma.h header file
to the include/linux/dma.
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Free Software Foundation mailing address has been moved in the past and some
of the addresses here are outdated. Remove them from file headers since the
COPYING file in the kernel sources includes it.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Add register offset table entry for the newer (v1.7.0) version of the BAM IP
found on MSM8916. Update the DT bindings documentation.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Tested-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The same error message is printed from different switch cases. Since both of
these jump into same error label we can move error print there and add a DMA
direction in order to make it easier to grep error from sources.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The same error message is printed from different functions. Add a function
name to error message in order to make it easier to grep error from sources.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The commit 9cade1a46c (dma: dw: split driver to library part and platform
code) introduced a separate platform driver but missed to add a
MODULE_ALIAS("platform:dw_dmac"); to that module.
The patch adds this to get driver loaded automatically if platform device is
registered.
Reported-by: "Blin, Jerome" <jerome.blin@intel.com>
Fixes: 9cade1a46c (dma: dw: split driver to library part and platform code)
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Below comments got from Page4724 of Reference Manual of i.mx6q:
http://cache.freescale.com/files/32bit/doc/ref_manual/IMX6DQRM.pdf
--"Static context mode should be used for the first channel called
after reset to ensure that the all context RAM for that channel is
initialized during the context SAVE phase when the channel is
done or yields. Subsequent calls to the same channel or
different channels may use any of the dynamic context modes.
This will ensure that all context locations for the bootload
channel are initialized, and prevent undefined values in context
RAM from being loaded during the context restore if the
channel is re-started later"
Unfortunately, the rule was broken by commit(5b28aa319b)
.This patch just take them back.
Signed-off-by: Robin Gong <b38343@freescale.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch fixes the following issues regarding to the calculation of the
residue:
1. The residue is always calculated for the current transfer even if the
cookie is associated to a pending transfer.
2. For scatter/gather DMA the calculation of the residue for the current
transfer doesn't include the bytes of the child descriptors that are already
transferred.
It only calculates the difference between the transfer's total length minus
the number of bytes that are already transferred for the current child
descriptor.
For example: There is a scatter/gather DMA transfer with a total length of
1 MByte. Getting the residue several times while the transfer is running shows
something like that:
1: residue = 975584
2: residue = 1002766
3: residue = 992627
4: residue = 983767
5: residue = 985694
6: residue = 1008094
7: residue = 1009741
8: residue = 1011195
3. The driver stores the residue but never resets it when starting a new
transfer.
For example: If there are two subsequent DMA transfers. The first one with
a total length of 1 MByte and the second one with a total length of 1 kByte.
Getting the residue for both transfers shows something like that:
transfer 1: residue = 975584
transfer 2: residue = 1048380
Changes from V1:
* Fixed coding style of the multi-line comments.
* Improved accuracy of the residue calculation when the transfer for the
first descriptor is active.
Changes from V2:
* Member 'tx_width' of 'struct at_desc' restored, because the transfer width
can't be derived from the source width when using "slave_sg".
The transfer width is needed for the calculation of the residue if either
the transfer of the first or the last descriptor is in progress.
In the case of a "memory_to_memory_sg" transfer (part of this patch
series) the transfer width of both descriptors may differ. Thus it is
required to additionally set 'tx_width' of the last descriptor.
* Added functions for multiply used calculations.
Signed-off-by: Torsten Fleischer <torfl6749@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch adds support for memory to memory scatter-gather transfers.
Changes from V1:
* Fixed coding style of the multi-line comments.
Changes from V2:
* Added setup of 'desc->tx_width' that is needed to calculate the
residue.
Signed-off-by: Torsten Fleischer <torfl6749@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The HSU DMA is developed to support High Speed UART controllers found in
particular on Intel MID platforms such as Intel Medfield.
The existing implementation is tighten to the drivers/tty/serial/mfd.c driver
and has a lot of disadvantages. Besides that we would like to get rid of the
old HS UART driver in regarding to extending the 8250 which supports generic
DMAEngine API. That's why the current driver has been developed.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the dmaengine complaint about missing slave caps :
- declare the available bus widths
- declare the available transfer types
- declare the residue calculation type
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Remove double check on chan->desc.
Found by Coccinelle.
Signed-off-by: Tapasweni Pathak <tapaswenipathak@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Since commit 7bced39751 ("net_dma: simple removal") removed the net_dma
support entirely, net_dma_find_channel has no users left. Remove the function
entirely.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Avoid the warning below triggered during dmaengine async device
registration.
WARNING: CPU: 1 PID: 1 at linux/drivers/dma/dmaengine.c:863
dma_async_device_register+0x2a8/0x4b8()
this driver doesn't support generic slave capabilities reporting
To do that fill mandatory .directions bit mask,
.src/dst_addr_widths and .residue_granularity dma_device fields
with appropriate values.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
BDX-DE IOATDMA reports incorrect DMACAP register for PQ related
ops. Ignoring those bits.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
When simplificating the channel configuration, the cyclic case has been
forgotten. It leads to use bad configuration causing many bugs.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
When dma controller is not used by any user and set off,
we should disble interrupt handler, at least the interrupt
reset part, for some subsystem, e.g. ADSP, may use the
dma in its own logic, here reset the interrupt may make
this subsystem work abnormally.
Signed-off-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Below are the refinements.
1. Set DMA abort bit when disabling dma channel. This will clear
the remaining data in dma FIFO, to fix channel-swap issue.
2. Read DMA HW pointer when updating DMA status. Previously dma
position is calculated by adding one period size in dma interrupt.
This is inaccurate/insufficient for some high-quality audio APP.
Since interrupt bottom half handler has variable schedule delay,
it causes big error when calculating sample delay. Read the actual
HW pointer and feedback can improve the accuracy.
3. Do some minor code clean.
Signed-off-by: Qiao Zhou <zhouqiao@marvell.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Fix spelling mistake, "aquire" -> "acquire" and missing newline (as
spotted by Joe Perches.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
During system reboot, the sh-dma-engine device may be runtime-suspended,
causing a crash:
Unhandled fault: imprecise external abort (0x1406) at 0x0002c02c
Internal error: : 1406 [#1] SMP ARM
...
PC is at sh_dmae_ctl_stop+0x28/0x64
LR is at sh_dmae_ctl_stop+0x24/0x64
If the sh-dma-engine is runtime-suspended, its module clock is turned
off, and its registers cannot be accessed.
To fix this, move the call to sh_dmae_ctl_stop(), which touches the
DMAOR register, to the sh_dmae_suspend() and sh_dmae_runtime_suspend()
callbacks. This makes PM operations more symmetric, as both
sh_dmae_resume() and sh_dmae_runtime_resume() already call sh_dmae_rst()
to re-initialize the DMAOR register.
Remove sh_dmae_shutdown(), as it became empty.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch fixes checkpatch.pl error in file ste_dma40.c
ERROR: space required before the open parenthesis '('
Signed-off-by: Dilek Uzulmez <dilekuzulmez@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some dma channels may be reserved for other purpose in other layer,
like secure driver in EL2/EL3. PDMA driver can see the interrupt
status, but it should not try to handle related interrupt, since it
doesn't belong to PDMA driver in kernel. These interrupts should be
handled by corresponding client/module.Otherwise, it will overwrite
illegal memory and cause unexpected issues, since pdma driver only
requests resources for pdma channels.
In PDMA driver, the reserved channels are at the end of total 32
channels. If we find interrupt bit index is not smaller than total
dma channels, we should ignore it.
Signed-off-by: Qiao Zhou <zhouqiao@marvell.com>
Acked-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Calls tasklet_kill() in error path of the probe function were missing.
Add the same in error path.
Signed-off-by: Pramod Gurav <pramod.gurav@smartplayin.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
in dma_slave_config, which is incompatible with the way that the
dmaengine API normally works.
I've had a closer look at the existing code now and found that all
slave drivers that pass a slave_id in dma_slave_config for SH do that
right after passing the same ID into shdma_chan_filter, so we can just
rely on that. However, the various shdma drivers currently do not
remember the slave ID that was passed into the filter function when
used in non-DT mode and only check the value to find a matching channel,
unlike all other drivers.
There might still be drivers that are not part of the kernel that rely
on setting the slave_id to some other value, so to be on the safe side,
this adds another 'real_slave_id' field to shdma_chan that remembers
the ID and uses it when a driver passes a zero slave_id in dma_slave_config,
like most drivers do.
Eventually, the real_slave_id and slave_id fields should just get merged
into one field, but that requires other changes.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Pull dmaengine updates from Vinod Koul:
"This update brings:
- the big cleanup up by Maxime for device control and slave
capabilities. This makes the API much cleaner.
- new IMG MDC driver by Andrew
- new Renesas R-Car Gen2 DMA Controller driver by Laurent along with
bunch of fixes on rcar drivers
- odd fixes and updates spread over driver"
* 'for-linus' of git://git.infradead.org/users/vkoul/slave-dma: (130 commits)
dmaengine: pl330: add DMA_PAUSE feature
dmaengine: pl330: improve pl330_tx_status() function
dmaengine: rcar-dmac: Disable channel 0 when using IOMMU
dmaengine: rcar-dmac: Work around descriptor mode IOMMU errata
dmaengine: rcar-dmac: Allocate hardware descriptors with DMAC device
dmaengine: rcar-dmac: Fix oops due to unintialized list in error ISR
dmaengine: rcar-dmac: Fix spinlock issues in interrupt
dmaenegine: edma: fix sparse warnings
dmaengine: rcar-dmac: Fix uninitialized variable usage
dmaengine: shdmac: extend PM methods
dmaengine: shdmac: use SET_RUNTIME_PM_OPS()
dmaengine: pl330: fix bug that cause start the same descs in cyclic
dmaengine: at_xdmac: allow muliple dwidths when doing slave transfers
dmaengine: at_xdmac: simplify channel configuration stuff
dmaengine: at_xdmac: introduce save_cc field
dmaengine: at_xdmac: wait for in-progress transaction to complete after pausing a channel
ioat: fail self-test if wait_for_completion times out
dmaengine: dw: define DW_DMA_MAX_NR_MASTERS
dmaengine: dw: amend description of dma_dev field
dmatest: move src_off, dst_off, len inside loop
...
This is a good healthy set of various code removals. Total net delta is 8100
lines removed.
Among the larger cleanups are:
- Removal of old Samsung S3C DMA infrastructure by Arnd
- Removal of the non-DT version of the 'lager' board by Magnus Damm
- General stale code removal on OMAP and Davinci by Rickard Strandqvist
- Removal of non-DT support on am3517 platforms by Tony Lindgren
... plus several other cleanups of various platforms across the board.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=tsjK
-----END PGP SIGNATURE-----
Merge tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Olof Johansson:
"This is a good healthy set of various code removals. Total net delta
is 8100 lines removed.
Among the larger cleanups are:
- Removal of old Samsung S3C DMA infrastructure by Arnd
- Removal of the non-DT version of the 'lager' board by Magnus Damm
- General stale code removal on OMAP and Davinci by Rickard Strandqvist
- Removal of non-DT support on am3517 platforms by Tony Lindgren
... plus several other cleanups of various platforms across the board"
* tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (47 commits)
ARM: sirf: drop redundant function and marco declaration
arm: omap: specify PMUs are for ARMv7 CPUs
arm: shmobile: specify PMUs are for ARMv7 CPUs
arm: iop: specify PMUs are for XScale CPUs
arm: pxa: specify PMUs are for XScale CPUs
arm: realview: specify PMU types
ARM: SAMSUNG: remove unused DMA infrastructure
ARM: OMAP3: Add back Kconfig option MACH_OMAP3517EVM for ASoC
ARM: davinci: Remove CDCE949 driver
ARM: at91: remove useless at91rm9200_set_type()
ARM: at91: remove useless at91rm9200_dt_initialize()
ARM: at91: move debug-macro.S into the common space
ARM: at91: remove useless at91_sysirq_mask_rtx
ARM: at91: remove useless config MACH_AT91SAM9_DT
ARM: at91: remove useless config MACH_AT91RM9200_DT
ARM: at91: remove unused mach/memory.h
ARM: at91: remove useless header file includes
ARM: at91: remove unneeded header file
rtc: at91/Kconfig: remove useless options
ARM: at91/Documentation: add a README for Atmel SoCs
...
DMA_PAUSE command is used for halting DMA transfer on chosen channel.
It can be useful when we want to safely read residue before terminating
all requests on channel. Otherwise there can be situation when some data
is transferred before channel termination but after reading residue,
which obviously results with data loss. To avoid this situation we can
pause channel, read residue and then terminate all requests.
This scenario is common, for example, in serial port drivers.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch adds possibility to read residue of DMA transfer. It's useful
when we want to know how many bytes have been transferred before we
terminate channel. It can take place, for example, on timeout interrupt.
Signed-off-by: Lukasz Czerwinski <l.czerwinski@samsung.com>
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
A still unconfirmed hardware bug prevents the IPMMU microTLB 0 to be
flushed correctly, resulting in memory corruption. DMAC 0 channel 0 is
connected to microTLB 0 on currently supported platforms, so we can't
use it with the IPMMU. As the IOMMU API operates at the device level we
can't disable it selectively, so ignore channel 0 for now if the device
is part of an IOMMU group.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
When descriptor memory is accessed through an IOMMU the DMADAR register
isn't initialized automatically from the first descriptor at beginning
of transfer by the DMAC like it should. Initialize it manually with the
destination address of the first chunk.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
When wired to an IOMMU to access data, the DMAC accesses the hardware
descriptors through the IOMMU as well. We're using the DMA mapping API
to allocate the descriptors, but with a NULL device at the moment, which
prevents IOMMU mappings from being created. Fix this by passing the DMAC
device instead.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The error interrupt handler stops and reinitializes all channels. This
causes a crash for channels that have never been used, as their
descriptor lists are uninitialized. Fix it by initializing the
descriptor lists at probe time.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The rcar_dmac_desc_put() function is called in interrupt context and
must thus use spin_lock_irqsave() instead of spin_lock_irq().
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
this patch fixes following sparse warnings:
edma.c:537:32: warning: symbol 'edma_prep_dma_memcpy' was not declared. Should it be static?
edma.c:1070:6: warning: symbol 'edma_filter_fn' was not declared. Should it be static?
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The desc variable is used uninitialized in the rcar_dmac_desc_get() and
rcar_dmac_xfer_chunk_get() functions if descriptors need to be
allocated. Fix it.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In order to make it possible to restore from hibernation not only in Linux but
also in e.g. U-Boot, we have to use sh_dmae_{suspend|resume}() for the {freeze|
thaw|restore}() PM methods. It's handy to achieve this with SIMPLE_DEV_PM_OPS()
macro; since that macro doesn't do anything when CONFIG_PM_SLEEP is undefined,
we don't need to #define sh_dmae_{suspend|resume} NULL anymore but we'll have to
enclose sh_dmae_{suspend|resume}() into the new #ifdef...
Based on original patch by Mikhail Ulyanov <mikhail.ulyanov@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Vinod Koul
Luis R. Rodriguez
Paul Gortmaker
Lars-Peter Clausen
Rameshwar Prasad Sahu
Dave Jiang
Jon Hunter
Fabio Estevam
Emilio López
Thomas Petazzoni
Michal Suchanek
Rob Herring
Zidan Wang
Ludovic Desroches
Alex Smith
Yanchang Li
Joachim Eastwood
Linus Walleij
Robert Jarzmik
Robert Baldyga
Robert Jarzmik
Allen Hubbe
Thomas Gleixner
Maxime Ripard
Jun Nie
Axel Lin
Shengjiu Wang
Linus Torvalds
Rafael J. Wysocki
Cyrille Pitchen
Andy Shevchenko
Peter Ujfalusi
Misael Lopez Cruz
Viresh Kumar
Jiang Liu
Maninder Singh
Krzysztof Kozlowski
Krzysztof Kozlowski
Jarkko Nikula
Vladimir Zapolskiy
Stefan Agner
Mark Brown
Lior Amsalem
Greg Kroah-Hartman
Hao Liu
Stephen Rothwell
Joe Perches
Geert Uytterhoeven
Kuninori Morimoto
Jens Kuske
Leonardo Carreras
John Ogness
Christopher Freeman
Jean Delvare
Geert Uytterhoeven
Arnd Bergmann
kbuild test robot
Alexey Khoroshilov
Niklas Cassel
Dan Carpenter
Yoshihiro Shimoda
Dmitry Eremin-Solenikov
Felipe Balbi
Xuelin Shi
Petr Kulhavy
Ben Dooks
Fabian Frederick
Kedareswara rao Appana
Archit Taneja
Robin Gong
Torsten Fleischer
Tapasweni Pathak
Stanimir Varbanov
Stanimir Varbanov
Jie Yang
Qiao Zhou
Colin Ian King
Dilek Uzulmez
Pramod Gurav
Laurent Pinchart
Lad, Prabhakar
Sergei Shtylyov