Device tree update for the Applied micro processor 460ex on-chip SATA to use
"dmas" property.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
There is a duplication in the debug messages when accessing SCR registers.
Remove duplication to make the messages neat.
Tested-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
DMA operates with physical addresses which is not exactly the same as ioremap()
returns.
Introduce variable to keep physical address of the SATA FIFO register and
supply it when prepare DMA channel.
Tested-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This simplifies error handling and cleanup by using devm to manage
IO mappings.
Tested-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This consolidates the reads from each of the if/else branches
to one place making the code a lot nicer to look at.
Tested-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Rename the register access macros and use standard _relaxed()
ops instead of __raw variants with explicit byte swapping.
The original driver used the ppc-specific in/out_le32(). When it
was adapted to other systems, these were added to the driver
under ifdefs. However, those names are not defined as macros on
ppc, so it ended up replacing them there as well with altered
semantics. This patch restores the original semantics on ppc and
makes the accesses no less strict on other systems.
Also fixes too many sparse warnings to count.
Tested-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Convert dmaengine_terminate_all() calls to synchronous and asynchronous
versions where appropriate.
Tested-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The pointer to the mmio register base is missing the __iomem
annotation. Fix this.
Tested-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The (void *__iomem) cast is wrong. Change the target type of the
"base" pointer to void __iomem instead and drop the cast.
Tested-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Casting a pointer to unsigned long only to immediately cast it back
to a pointer makes no sense. Fix this.
Tested-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The sata_dwc_qc_prep() does nothing. Use the default ata_noop_qc_prep
instead.
Tested-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Here we refactor HOSTDEV{P}_FROM_*() macros to fit one line and fix the
definition of HSDEV_FROM_HSDEVP() where wrong name of the parameter waas used.
Tested-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This moves all global data into the driver private struct, thus
permitting multiple devices of this type to be used.
The core_scr_read/write() functions are replaced with equivalent
calls to the existing sata_dwc_scr_read/write().
Tested-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This adds support for powering on an optional PHY when activating the
device.
Tested-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Currently this driver only works with a DesignWare DMA engine which it
registers manually using the second "reg" address range and interrupt
number from the DT node.
This patch makes the driver instead use the "dmas" property if present,
otherwise optionally falling back on the old way so existing device
trees can continue to work.
With this change, there is no longer any reason to depend on the 460EX
machine type so drop that from Kconfig.
Tested-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
ata_sff_qc_issue() can't handle DMA commands and thus we have to avoid it for
them. Do call ata_bmdma_qc_issue() instead for this case. Note that the former
one distinguishes PIO and DMA mode and behaves accordingly.
Suggested-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Calling dmaengine_prep_slave_sg() for non-dma ATA commands is
unnecessary at best and could be harmful if the dma driver reacts
badly to this. It also causes this driver to print a bogus error
message in these cases.
This patch changes sata_dwc_qc_issue() to only do the dma setup
for dma commands and also reports an error to libata if if fails.
Tested-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
There is no need to have a platform driver compiled since the DMA driver is
used as a library.
Tested-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
In the original code the DMA is always a flow controller. Set this accordingly
in updated code.
Tested-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The burst size as defined by DMAengine API is in items of address width. Derive
burst size from AHB_DMA_BRST_DFLT (64 bytes) by dividing it to
DMA_SLAVE_BUSWIDTH_4_BYTES (4 bytes) that gives us 16 items.
Tested-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The original code states:
Make sure a LLI block is not created that will span 8K max FIS
boundary. If the block spans such a FIS boundary, there is a chance
that a DMA burst will cross that boundary -- this results in an error
in the host controller.
Since we have switched to generic DMAengine API we satisfy above by setting
dma_boundary value to 0x1fff.
Suggested-by: Mans Rullgard <mans@mansr.com>
Tested-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This patch fixes Machine Check "Data Write PLB Error" which happens
when libata-sff's ata_sff_dev_select is trying to write into the
device_addr in order to select a drive. However, SATA has no master
or slave devices like the old ATA Bus, therefore selecting a
different drive is kind of pointless.
Data Write PLB Error
Oops: Machine check, sig: 7 [#1]
PowerPC 44x Platform
Modules linked in:
CPU: 0 PID: 508 Comm: scsi_eh_0 Not tainted 4.6.0-rc3-next-20160412+ #10
[...]
NIP [c027e820] ata_sff_dev_select+0x3c/0x44
LR [c027e810] ata_sff_dev_select+0x2c/0x44
Call Trace:
[cec31cd0] [c027da00] ata_sff_postreset+0x40/0xb4 (unreliable)
[cec31ce0] [c027a03c] ata_eh_reset+0x5cc/0x928
[cec31d60] [c027a840] ata_eh_recover+0x330/0x10bc
[cec31df0] [c027bae0] ata_do_eh+0x4c/0xa4
[...]
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
We pass struct dw_dma_chip to dw_dma_probe() anyway, thus we may use it to
pass a platform data as well.
While here, constify the source of the platform data.
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Keep the entire platform data in the struct dw_dma.
It makes the driver a bit cleaner.
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
There several changes are done here:
- Convert the property to be in bytes
Besides that this is a common practice for such property, the use of a value
in bytes much more convenient than handling the encoded one.
- Rename data_width to data-width in the device tree bindings
The change leaves the support for the old format as well just in case someone
will use a newer kernel with an old device tree blob.
- While here, replace dwc_fast_ffs() by __ffs()
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The value of nr_masters equal to 0 is invalid since this DMA controller has to
have at least one master.
Check this before we proceed with the rest of properties.
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch changes the driver to allocate DMA descriptors when
needed. This stops memory resources to be wasted and letting
them sit idle in the free_list structure when the device doesn't
need it... This also solves the problem, that a driver has to
guess the number of how many descriptors it needs to allocate
in advance. Currently, the dma engine will just fail when put
under load by sata_dwc_460ex.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
To be sure we have the cyclic transfers already gone we set cdesc to NULL. It
will prevent the double free.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Residue is a property of any active descriptor. So, any descriptor may be in
different state but residue is a feature of active descriptor. Check if the
asked descriptor is active and return proper residue value for it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
We have already dedicated variable for flags, therefore no need to create an
additional storage for that. Covert dwc->initialized to use dwc->flags.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
We have already dedicated variable for flags, therefore no need to create an
additional storage for that. Convert dwc->paused to use dwc->flags.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The code is fixed to satisfy a compiler otherwise we have
drivers/dma/dw/core.c: In function ‘dwc_handle_cyclic’:
drivers/dma/dw/core.c:568: warning: comparison between signed and unsigned
drivers/dma/dw/core.c: In function ‘dw_dma_tasklet’:
drivers/dma/dw/core.c:590: warning: comparison between signed and unsigned
drivers/dma/dw/core.c: In function ‘dw_dma_off’:
drivers/dma/dw/core.c:1103: warning: comparison between signed and unsigned
drivers/dma/dw/core.c: In function ‘dw_dma_cyclic_free’:
drivers/dma/dw/core.c:1469: warning: comparison between signed and unsigned
drivers/dma/dw/core.c: In function ‘dw_dma_probe’:
drivers/dma/dw/core.c:1574: warning: comparison between signed and unsigned
There is no functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Since struct dw_dma is allocated and regs member is assigned properly we can
use standard IO accessors to the DMA registers.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The datasheet requires that the LLP_[SD]_EN bits be cleared whenever
LLP.LOC is zero, i.e. in the last descriptor of a multi-block chain.
Make the driver do this.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The LMS field indicates from which master the descriptor is to be
read. This patch assumes this is always the same as the memory
side in a peripheral transfer which is true for all known systems.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
If the DMA controller uses a different byte order than the host CPU,
the hardware linked list descriptor fields need to be byte-swapped.
This patch makes the driver write these fields using the same byte
order it uses for mmio accesses to the DMA engine. I do not know
if this is guaranteed to always be correct.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
On some architectures the DMA controller can have two masters connected to
different buses and thus access to memory is possible only through one and
to peripheral through the other.
This patch changes the src and dst master setting to match the direction
of the transfer.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The source and destination masters are reflecting buses or their layers to
where the different devices can be connected. The patch changes the master
names to reflect which one is related to which independently on the transfer
direction.
The outcome of the change is that the memory data width is now always limited
by a data width of the master which is dedicated to communicate to memory.
The patch will not break anything since all current users have the same data
width for all masters. Though it would be nice to revisit avr32 platforms to
check what is the actual hardware topology in use there. It seems that it has
one bus and two masters on it as stated by Table 8-2, that's why everything
works independently on the master in use. The purpose of the sequential patch
is to fix the driver for configuration of more than one bus.
The change is done in the assumption that src_master and dst_master are
reflecting a connection to the memory and peripheral correspondently on avr32
and otherwise on the rest.
Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The commit 8950052029 ("dmaengine: dw: apply both HS interfaces and remove
slave_id usage") cleaned up the code to avoid usage of depricated slave_id
member of generic slave configuration.
Meanwhile it broke the master selection by removing important call to
dwc_set_masters() in ->device_alloc_chan_resources() which copied masters from
custom slave configuration to the internal channel structure.
Everything works until now since there is no customized connection of
DesignWare DMA IP to the bus, i.e. one bus and one or more masters are in use.
The configurations where 2 masters are connected to the different masters are
not working anymore. We are expecting one user of such configuration and need
to select masters properly. Besides that it is obviously a performance
regression since only one master is in use in multi-master configuration.
Select masters in accordance with what user asked for. Keep this patch in a form
more suitable for back porting.
We are safe to take necessary data in ->device_alloc_chan_resources() because
we don't support generic slave configuration embedded into custom one, and thus
the only way to provide such is to use the parameter to a filter function which
is called exactly before channel resource allocation.
While here, replase BUG_ON to less noisy dev_warn() and prevent channel
allocation in case of error.
Fixes: 8950052029 ("dmaengine: dw: apply both HS interfaces and remove slave_id usage")
Cc: stable@vger.kernel.org
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Pull Ceph updates from Sage Weil:
"There is quite a bit here, including some overdue refactoring and
cleanup on the mon_client and osd_client code from Ilya, scattered
writeback support for CephFS and a pile of bug fixes from Zheng, and a
few random cleanups and fixes from others"
[ I already decided not to pull this because of it having been rebased
recently, but ended up changing my mind after all. Next time I'll
really hold people to it. Oh well. - Linus ]
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client: (34 commits)
libceph: use KMEM_CACHE macro
ceph: use kmem_cache_zalloc
rbd: use KMEM_CACHE macro
ceph: use lookup request to revalidate dentry
ceph: kill ceph_get_dentry_parent_inode()
ceph: fix security xattr deadlock
ceph: don't request vxattrs from MDS
ceph: fix mounting same fs multiple times
ceph: remove unnecessary NULL check
ceph: avoid updating directory inode's i_size accidentally
ceph: fix race during filling readdir cache
libceph: use sizeof_footer() more
ceph: kill ceph_empty_snapc
ceph: fix a wrong comparison
ceph: replace CURRENT_TIME by current_fs_time()
ceph: scattered page writeback
libceph: add helper that duplicates last extent operation
libceph: enable large, variable-sized OSD requests
libceph: osdc->req_mempool should be backed by a slab pool
libceph: make r_request msg_size calculation clearer
...
Pull orangefs filesystem from Mike Marshall.
This finally merges the long-pending orangefs filesystem, which has been
much cleaned up with input from Al Viro over the last six months. From
the documentation file:
"OrangeFS is an LGPL userspace scale-out parallel storage system. It
is ideal for large storage problems faced by HPC, BigData, Streaming
Video, Genomics, Bioinformatics.
Orangefs, originally called PVFS, was first developed in 1993 by Walt
Ligon and Eric Blumer as a parallel file system for Parallel Virtual
Machine (PVM) as part of a NASA grant to study the I/O patterns of
parallel programs.
Orangefs features include:
- Distributes file data among multiple file servers
- Supports simultaneous access by multiple clients
- Stores file data and metadata on servers using local file system
and access methods
- Userspace implementation is easy to install and maintain
- Direct MPI support
- Stateless"
see Documentation/filesystems/orangefs.txt for more in-depth details.
* tag 'ofs-pull-tag-1' of git://git.kernel.org/pub/scm/linux/kernel/git/hubcap/linux: (174 commits)
orangefs: fix orangefs_superblock locking
orangefs: fix do_readv_writev() handling of error halfway through
orangefs: have ->kill_sb() evict the VFS side of things first
orangefs: sanitize ->llseek()
orangefs-bufmap.h: trim unused junk
orangefs: saner calling conventions for getting a slot
orangefs_copy_{to,from}_bufmap(): don't pass bufmap pointer
orangefs: get rid of readdir_handle_s
ornagefs: ensure that truncate has an up to date inode size
orangefs: move code which sets i_link to orangefs_inode_getattr
orangefs: remove needless wrapper around GFP_KERNEL
orangefs: remove wrapper around mutex_lock(&inode->i_mutex)
orangefs: refactor inode type or link_target change detection
orangefs: use new getattr for revalidate and remove old getattr
orangefs: use new getattr in inode getattr and permission
orangefs: use new orangefs_inode_getattr to get size in write and llseek
orangefs: use new orangefs_inode_getattr to create new inodes
orangefs: rename orangefs_inode_getattr to orangefs_inode_old_getattr
orangefs: remove inode->i_lock wrapper
orangefs: put register_chrdev immediately before register_filesystem
...
translation window setup, NULL ptr dereference, and ntb-perf errors.
Also, a modification to the driver API that makes _addr functions
optional.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=7DcD
-----END PGP SIGNATURE-----
Merge tag 'ntb-4.6' of git://github.com/jonmason/ntb
Pull NTB bug fixes from Jon Mason:
"NTB bug fixes for tasklet from spinning forever, link errors,
translation window setup, NULL ptr dereference, and ntb-perf errors.
Also, a modification to the driver API that makes _addr functions
optional"
* tag 'ntb-4.6' of git://github.com/jonmason/ntb:
NTB: Remove _addr functions from ntb_hw_amd
NTB: Make _addr functions optional in the API
NTB: Fix incorrect clean up routine in ntb_perf
NTB: Fix incorrect return check in ntb_perf
ntb: fix possible NULL dereference
ntb: add missing setup of translation window
ntb: stop link work when we do not have memory
ntb: stop tasklet from spinning forever during shutdown.
ntb: perf test: fix address space confusion
The only new stuff which missed the first pull request is an update to
the UFS driver. The rest is an assortment of bug fixes and minor
tweaks which appeared recently (some are fixes for recent code and
some are stuff spotted recently by the checkers or the new gcc-6
compiler [most of Arnd's stuff]).
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABAgAGBQJW9nPcAAoJEDeqqVYsXL0M4CIH/1EkSjCyLzm5yDGzPKyD8LuS
r8mNmXEgKxKuCVenmsydDEa4YmEH/94ysMevwXCogDvUz0ms/qRHJnF3cy7MT7fe
TlcuKQdshl3k5gRP33K3AkK1aNtzyWGwiP+5+e+uO3rzJgujJa+IcpvYYk/e46GE
yTfi6uEdNRFD6xGxqfttvO9I+YKj5XtRpNZQe/YAS6bcyLm0R62031b8OcmKxWYT
m/F9AlxKeIDmutH5GK5siePQ1KNmn1LZOGYO8RKA4jcyzhxJ8qv8HdRpFGAGuyg/
f7V0OGqhLGlzZ5pNRfsYpAhoScmwbm+rYJv1W0vjRdeoAgmNkR8S5LDeXHpvZ5A=
=2sEy
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull more SCSI updates from James Bottomley:
"The only new stuff which missed the first pull request is an update to
the UFS driver.
The rest is an assortment of bug fixes and minor tweaks which appeared
recently (some are fixes for recent code and some are stuff spotted
recently by the checkers or the new gcc-6 compiler [most of Arnd's
stuff])"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (32 commits)
scsi_common: do not clobber fixed sense information
scsi: ufs: select CONFIG_NLS
scsi: fc: use get/put_unaligned64 for wwn access
fnic: move printk()s outside of the critical code section.
qla2xxx: avoid maybe_uninitialized warning
megaraid_sas: add missing curly braces in ioctl handler
lpfc: fix misleading indentation
scsi_transport_sas: add 'scsi_target_id' sysfs attribute
scsi_dh_alua: uninitialized variable in alua_check_vpd()
scsi: ufs-qcom: add printouts of testbus debug registers
scsi: ufs-qcom: enable/disable the device ref clock
scsi: ufs-qcom: set PA_Local_TX_LCC_Enable before link startup
scsi: ufs: add device quirk delay before putting UFS rails in LPM
scsi: ufs: fix leakage during link off state
scsi: ufs: tune UniPro parameters to optimize hibern8 exit time
scsi: ufs: handle non spec compliant bkops behaviour by device
scsi: ufs: add retry for query descriptors
scsi: ufs: add error recovery after DL NAC error
scsi: ufs: make error handling bit faster
scsi: ufs: disable vccq if it's not needed by UFS device
...
Commit 0b81d07790 ("fs crypto: move per-file encryption from f2fs
tree to fs/crypto") moved the f2fs crypto files to fs/crypto/ and
renamed the symbol prefixes from "f2fs_" to "fscrypt_" (and from "F2FS_"
to just "FS" for preprocessor symbols).
Because of the symbol renaming, it's a bit hard to see it as a file
move: use
git show -M30 0b81d07790
to lower the rename detection to just 30% similarity and make git show
the files as renamed (the header file won't be shown as a rename even
then - since all it contains is symbol definitions, it looks almost
completely different).
Even with the renames showing as renames, the diffs are not all that
easy to read, since so much is just the renames. But Eric Biggers
noticed that it's not just all renames: the initialization of the
xts_tweak had been broken too, using the inode number rather than the
page offset.
That's not right - it makes the xfs_tweak the same for all pages of each
inode. It _might_ make sense to make the xfs_tweak contain both the
offset _and_ the inode number, but not just the inode number.
Reported-by: Eric Biggers <ebiggers3@gmail.com>
Cc: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Kernel zero day testing warned about address space confusion. A virtual
iomem address was used where a physical address is expected. The
offending functions implement an optional part of the api, so they are
removed. They can be added later, after testing.
Fixes: a1b3695820
Signed-off-by: Allen Hubbe <Allen.Hubbe@emc.com>
Acked-by: Xiangliang Yu <Xiangliang.Yu@amd.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
* switch orangefs_remount() to taking ORANGEFS_SB(sb) instead of sb
* remove from the list _before_ orangefs_unmount() - request_mutex
in the latter will make sure that nothing observed in the loop in
ORANGEFS_DEV_REMOUNT_ALL handling will get freed until the end
of loop
* on removal, keep the forward pointer and zero the back one. That
way we can drop and regain the spinlock in the loop body (again,
ORANGEFS_DEV_REMOUNT_ALL one) and still be able to get to the
rest of the list.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Mike Marshall <hubcap@omnibond.com>
Error should only be returned if nothing had been read/written.
Otherwise we need to report a short read/write instead.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Mike Marshall <hubcap@omnibond.com>
Andy Shevchenko
Mans Rullgard
Christian Lamparter
Linus Torvalds
Allen Hubbe
Al Viro