Add a new parameter to ib_register_device() so that low-level device
drivers can pass in a pointer to a callback function that will be
called for each port that is registered in sysfs. This allows
low-level device drivers to create files in
/sys/class/infiniband/<hca>/ports/<N>/
without having to poke through the internals of the RDMA sysfs handling.
There is no need for an unregister function since the kobject
reference will go to zero when ib_unregister_device() is called.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* 'acpica' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (22 commits)
ACPI: fix early DSDT dmi check warnings on ia64
ACPICA: Update version to 20100428.
ACPICA: Update/clarify some parameter names associated with acpi_handle
ACPICA: Rename acpi_ex_system_do_suspend->acpi_ex_system_do_sleep
ACPICA: Prevent possible allocation overrun during object copy
ACPICA: Split large file, evgpeblk
ACPICA: Add GPE support for dynamically loaded ACPI tables
ACPICA: Clarify/rename some root table descriptor fields
ACPICA: Update version to 20100331.
ACPICA: Minimize the differences between linux GPE code and ACPICA code base
ACPI: add boot option acpi=copy_dsdt to fix corrupt DSDT
ACPICA: Update DSDT copy/detection.
ACPICA: Add subsystem option to force copy of DSDT to local memory
ACPICA: Add detection of corrupted/replaced DSDT
ACPICA: Add write support for DataTable operation regions
ACPICA: Fix for acpi_reallocate_root_table for incorrect root table copy
ACPICA: Update comments/headers, no functional change
ACPICA: Update version to 20100304
ACPICA: Fix for possible fault in acpi_ex_release_mutex
ACPICA: Standardize integer output for ACPICA warnings/errors
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6: (250 commits)
ALSA: hda: Storage class should be before const qualifier
ASoC: tpa6130a2: Remove CPVSS and HPVdd supplies
ASoC: tpa6130a2: Define output pins with SND_SOC_DAPM_OUTPUT
ASoC: sdp4430 - add sdp4430 pcm ops to DAI.
ASoC: TWL6040: Enable earphone path in codec
ASoC: SDP4430: Add support for Earphone speaker
ASoC: SDP4430: Add sdp4430 machine driver
ASoC: tlv320dac33: Avoid powering off while in BIAS_OFF
ASoC: tlv320dac33: Use dev_dbg in dac33_hard_power function
ALSA: sound/pci/asihpi: Use kzalloc
ALSA: hdmi - dont fail on extra nodes
ALSA: intelhdmi - add id for the CougarPoint chipset
ALSA: intelhdmi - user friendly codec name
ALSA: intelhdmi - add dependency on SND_DYNAMIC_MINORS
ALSA: asihpi: incorrect range check
ALSA: asihpi: testing the wrong variable
ALSA: es1688: add pedantic range checks
ARM: McBSP: Add support for omap4 in McBSP driver
ARM: McBSP: Fix request for irq in OMAP4
OMAP: McBSP: Add 32-bit mode support
...
* 'for-linus/i2c-2635' of git://git.fluff.org/bjdooks/linux: (21 commits)
i2c-highlander: remover superflous variable
i2c-ibm-iic: drop NO_IRQ
i2c-cpm: drop NO_IRQ
i2c-mpc: drop NO_IRQ
MAINTAINERS: add i2c tree for embedded platforms
i2c-pxa: only define 'blue_murder'-function if DEBUG is #defined
i2c-pxa: remove unused macro
i2c-nomadik: fix operator precedence warning
i2c-nomadik: release region when removed
OMAP3: I2C: Clean up Errata 1p153 handling
OMAP2/3: I2C: Errata ID i207: Clear wrong RDR interrupt
omap: i2c: add a timeout to the busy waiting
omap: i2c: make errata 1.153 workaround a separate function
i2c-omap: add mpu wake up latency constraint in i2c
omap: i2c: Add i2c support on omap4 platform
i2c-bfin-twi: return completion in interrupt for smbus quick transfers
i2c-bfin-twi: remove redundant retry
i2c-bfin-twi: fix lost interrupts at high speeds
i2c-bfin-twi: add debug output for error status
i2c-bfin-twi: integrate timeout timer with completion interface
...
* 'v4l_for_2.6.35' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (534 commits)
V4L/DVB (13554a): v4l: Use the video_drvdata function in drivers
V4L/DVB: vivi and mem2mem_testdev need slab.h to build
V4L/DVB: tm6000: bugfix image position
V4L/DVB: IR/imon: remove dead IMON_KEY_RELEASE_OFFSET
V4L/DVB: tm6000: README - add vbi
V4L/DVB: Fix unlock logic at medusa_video_init
V4L/DVB: fix dvb frontend lockup
V4L/DVB: s2255drv: remove dead code
V4L/DVB: s2255drv: return if vdev not found
V4L/DVB: ov511: cleanup: remove unneeded null check
V4L/DVB: media/mem2mem: dereferencing free memory
V4L/DVB: media/IR: Add missing include file to rc-map.c
V4L/DVB: dvb/stv6110x: cleanup error handling
V4L/DVB: ngene: Add lgdt3303 and mt2131 deps to Kconfig
V4L/DVB: ngene: start separating out DVB functions into separate file
V4L/DVB: ngene: split out card specific code into a separate file
V4L/DVB: ngene: split out i2c code into a separate file
V4L/DVB: ngene: add initial support for digital side of Avermedia m780
V4L/DVB: ngene: properly support boards where channel 0 isn't a TS input
V4L-DVB: ngene: make sure that tuner headers are included
...
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev: (49 commits)
libata-sff: separate out BMDMA qc_issue
libata-sff: prd is BMDMA specific
libata-sff: ata_sff_[dumb_]qc_prep are BMDMA specific
libata-sff: separate out BMDMA EH
libata-sff: port_task is SFF specific
libata-sff: ap->[last_]ctl are SFF specific
libata-sff: rename ap->ops->drain_fifo() to sff_drain_fifo()
libata-sff: introduce ata_sff_init/exit() and ata_sff_port_init()
libata-sff: clean up BMDMA initialization
libata-sff: clean up inheritance in several drivers
libata-sff: reorder SFF/BMDMA functions
sata_inic162x: kill PORT_PRD_ADDR initialization
libata: kill ATA_FLAG_DISABLED
libata-sff: kill unused prototype and make ata_dev_select() static
libata-sff: update bmdma host bus error handling
sata_mv: remove unnecessary initialization
sata_inic162x: inic162x is not dependent on CONFIG_ATA_SFF
pata_sch: use ata_pci_sff_init_one()
pata_sil680: Do our own exec_command posting
libata: Remove excess delay in the tf_load path
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (44 commits)
vlynq: make whole Kconfig-menu dependant on architecture
add descriptive comment for TIF_MEMDIE task flag declaration.
EEPROM: max6875: Header file cleanup
EEPROM: 93cx6: Header file cleanup
EEPROM: Header file cleanup
agp: use NULL instead of 0 when pointer is needed
rtc-v3020: make bitfield unsigned
PCI: make bitfield unsigned
jbd2: use NULL instead of 0 when pointer is needed
cciss: fix shadows sparse warning
doc: inode uses a mutex instead of a semaphore.
uml: i386: Avoid redefinition of NR_syscalls
fix "seperate" typos in comments
cocbalt_lcdfb: correct sections
doc: Change urls for sparse
Powerpc: wii: Fix typo in comment
i2o: cleanup some exit paths
Documentation/: it's -> its where appropriate
UML: Fix compiler warning due to missing task_struct declaration
UML: add kernel.h include to signal.c
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/core: Use kmemdup() instead of kmalloc()+memcpy()
IB/iser: Fix error flow in iser_create_ib_conn_res()
IB/iser: Enhance disconnection logic for multi-pathing
IB/iser: Remove buggy back-pointer setting
IB/iser: Add asynchronous event handler
MAINTAINERS: Add cxgb4 and iw_cxgb4 entries
RDMA/cxgb3: Shrink .text with compile-time init of handlers arrays
IPoIB: Allow disabling/enabling TSO on the fly through ethtool
IB/mlx4: Add support for masked atomic operations
IB/core: Add support for masked atomic operations
RDMA/cma: Randomize local port allocation
RDMA/nes: Make unnecessarily global functions static
RDMA/nes: Make nesadapter->phy_lock usage consistent
RDMA/cxgb4: Add driver for Chelsio T4 RNIC
IB/mthca: Use the dma state API instead of pci equivalents
RDMA/amso1100: Use the dma state API instead of pci equivalents
RDMA/cxgb3: Don't free skbs on NET_XMIT_* indications from LLD
RDMA/cxgb3: Use the dma state API instead of pci equivalents
IB: Explicitly rule out llseek to avoid BKL in default_llseek()
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6: (61 commits)
KEYS: Return more accurate error codes
LSM: Add __init to fixup function.
TOMOYO: Add pathname grouping support.
ima: remove ACPI dependency
TPM: ACPI/PNP dependency removal
security/selinux/ss: Use kstrdup
TOMOYO: Use stack memory for pending entry.
Revert "ima: remove ACPI dependency"
Revert "TPM: ACPI/PNP dependency removal"
KEYS: Do preallocation for __key_link()
TOMOYO: Use mutex_lock_interruptible.
KEYS: Better handling of errors from construct_alloc_key()
KEYS: keyring_serialise_link_sem is only needed for keyring->keyring links
TOMOYO: Use GFP_NOFS rather than GFP_KERNEL.
ima: remove ACPI dependency
TPM: ACPI/PNP dependency removal
selinux: generalize disabling of execmem for plt-in-heap archs
LSM Audit: rename LSM_AUDIT_NO_AUDIT to LSM_AUDIT_DATA_NONE
CRED: Holding a spinlock does not imply the holding of RCU read lock
SMACK: Don't #include Ext2 headers
...
WARNING: at drivers/firmware/dmi_scan.c:423 dmi_matches+0x70/0x160()
dmi check: not initialized yet.
This is caused by commit aa2110c
(ACPI: add boot option acpi=copy_dsdt to fix corrupt DSDT).
DMI is not initialized yet in acpi_early_init on ia64.
The DSDT DMI check table is x86 specific, so make it empty on other archs.
And this fixes the warnings on ia64.
Reported-and-tested-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
* 'bkl/procfs' of git://git.kernel.org/pub/scm/linux/kernel/git/frederic/random-tracing:
sunrpc: Include missing smp_lock.h
procfs: Kill the bkl in ioctl
procfs: Push down the bkl from ioctl
procfs: Use generic_file_llseek in /proc/vmcore
procfs: Use generic_file_llseek in /proc/kmsg
procfs: Use generic_file_llseek in /proc/kcore
procfs: Kill BKL in llseek on proc base
When cppcheck found this flaw
[./i2c/busses/i2c-highlander.c:284]: (style) Warning - using char variable in bit operation
it was noted that the 'read'-variable could be simply removed as read_write can
only be 0 or 1 anyhow. So, we remove the flaw and simplify the code.
Reported-by: d binderman <dcb314@hotmail.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Jean Delvare <khali@linux-fr.org>
Cc: Ben Dooks <ben-linux@fluff.org>
Drop NO_IRQ as 0 is the preferred way to describe 'no irq'
(http://lkml.org/lkml/2005/11/21/221). This change is safe, as the driver is
only used on powerpc, where NO_IRQ is 0 anyhow.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Sean MacLennan <smaclennan@pikatech.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Drop NO_IRQ as 0 is the preferred way to describe 'no irq'
(http://lkml.org/lkml/2005/11/21/221). This change is safe, as the driver is
only used on powerpc, where NO_IRQ is 0 anyhow.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Jochen Friedrich <jochen@scram.de>
Cc: Ben Dooks <ben-linux@fluff.org>
Drop NO_IRQ as 0 is the preferred way to describe 'no irq'
(http://lkml.org/lkml/2005/11/21/221). This change is safe, as the driver is
only used on powerpc, where NO_IRQ is 0 anyhow.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Ben Dooks <ben-linux@fluff.org>
This talkative function is also called on timeouts. As timeouts can
happen on regular writes to EEPROMs (no error case), this creates false
positives. Giving lots of details is interesting only for developers
anyhow, so just use the function if DEBUG is #defined.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Cc: Roel Kluin <roel.kluin@gmail.com>
Cc: Pavel Machek <pavel@ucw.cz>
Commit
beea494 ([ARM] Remove EEPROM slave emulation from i2c-pxa driver.)
removed all uses of eedbg, so the definition can go, too.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Fix this warning:
i2c-nomadik.c:707: warning: suggest parentheses around operand of '!' or change '&' to '&&' or '!' to '~'
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
So that the module can be loaded again after an unload.
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Clean up existing Errata 1p153 handling to use generic
errata handling mechanism through dev flag.
Signed-off-by: Manjunatha GK <manjugk@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Alexander Shishkin <virtuoso@slind.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Under certain rare conditions, I2C_STAT[13].RDR bit may be set
and the corresponding interrupt fire, even there is no data in
the receive FIFO, or the I2C data transfer is still ongoing.
These spurious RDR events must be ignored by the software.
This patch handles and ignores RDR spurious interrupts.
The below sequence is required in interrupt handler for
handling this errata:
1. If RDR is set to 1, clear RDR
2. Read I2C status register and check for BusBusy bit. If BusBusy
bit is set, skip remaining steps.
3. If BusBusy bit is not set, perform read operation on I2C status
register.
4. If RDR is set, clear the same. Check RDR again and clear if it sets
RDR bit again.
5. Perform I2C Data Read operation N number of times(where N is value
read from the register BUFSTAT-RXSTAT bit fields).
Note:
This errata is not applicable for omap2420 and omap4.
It is applicable for:
1. omap2430
2. omap34xx(including omap3630).
Signed-off-by: Manjunatha GK <manjugk@ti.com>
Cc: Hema Kalliguddi <hemahk@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Aaro Koskinen <Aaro.Koskinen@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The errata 1.153 workaround is busy waiting on XUDF bit in interrupt
context, which may lead to kernel hangs. The problem can be reproduced
by running the bus with wrong (too high) speed.
Signed-off-by: Alexander Shishkin <virtuoso@slind.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This is to avoid insanely long lines and levels of indentation.
Signed-off-by: Alexander Shishkin <virtuoso@slind.org>
Cc: Nishant Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
While waiting for completion of the i2c transfer, the
MPU could hit OFF mode and cause several msecs of
delay that made i2c transfers fail more often. The
extra delays and subsequent re-trys cause i2c clocks
to be active more often. This has also an negative
effect on power consumption.
Created a mechanism for passing and using the
constraint setting function in driver code. The used
mpu wake up latency constraints are now set individually
per bus, and they are calculated based on clock rate
and fifo size.
Thanks to Jarkko Nikula, Moiz Sonasath, Paul Walmsley,
and Nishanth Menon for tuning out the details of
this patch.
Updates by Kevin as requested by Tony:
- Remove omap_set_i2c_constraint_func() in favor of conditionally
adding the flag in omap_i2c_add_bus() in order to keep all the OMAP
conditional checking in a single location.
- Update set_mpu_wkup_lat prototypes to match OMAP PM layer so
OMAP PM function can be used directly in pdata.
Cc: Moiz Sonasath <m-sonasath@ti.com>
Cc: Jarkko Nikula <jhnikula@gmail.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Kalle Jokiniemi <kalle.jokiniemi@digia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch is rebased version of earlier post to add I2C
driver support to OMAP4 platform. On OMAP4, all
I2C register address offsets are changed from OMAP1/2/3 I2C.
In order to not have #ifdef's at various places in code,
as well as to support multi-OMAP build, an array is created
to hold the register addresses with it's offset.
This patch was submitted, reviewed and acked on mailing list
already. For more details refer below link
http://www.mail-archive.com/linux-i2c@vger.kernel.org/msg02281.html
This updated verion has a depedancy on "Add support for 16-bit registers"
posted on linux-omap. Below is the patch-works link for the same
http://patchwork.kernel.org/patch/72295/
Signed-off-by: Syed Rafiuddin <rafiuddin.syed@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Cc: Cory Maccarrone <darkstar6262@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
A smbus quick transfer has no data after the address byte.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
i2c event of next read/write byte may trigger before current int state
is cleared in the interrupt handler. So, this should be done at the
beginning of interrupt handler to avoid losing new i2c events.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add some debug() code to decode the error register.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
There isn't much point in managing our own custom timeout timer when the
completion interface already includes support for it. This makes the
resulting code much simpler and robust.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The S3C I2C controller indicates completion of I2C transfers before
the bus has a stop condition on it. In order to ensure that we do not
attempt to start a new transfer before the bus is idle the driver
currently inserts a 1ms delay. This is vastly larger than is generally
required and has a visible effect on performance under load, such as
when bringing up audio CODECs or reading back status information with
non-bulk I2C reads.
Replace the sleep with a spin on the IIC status register for up to 1ms.
This will busy wait but testing on my SMDK6410 system indicates that
the overwhelming majority of transactions complete on the first spin,
with maximum latencies of less than 10 spins so the absolute overhead
of busy waiting should be at worst comprable to msleep(), and the
overall system performance is dramatically improved.
The main risk is poor interaction with multimaster systems where
we may miss the bus going idle before the next transaction. Defend
against this by falling back to the original 1ms delay after 20 spins.
The overall effect in my testing is an approximately 20% improvement
in kernel startup time.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
sparc: Define ARCH_SLAB_MINALIGN
drivers/sbus/char/flash.c: flash_read should update ppos instead of file->f_pos
sparc64: Fix stack dumping and tracing when function graph is enabled.
sparc64: Show stack backtrace from show_regs() just like other platforms.
* 'davinci-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-davinci: (48 commits)
Revert "rtc: omap: let device wakeup capability be configured from chip init logic"
DM365: Added more PINMUX configurations for AEMIF
DM365: Make CLKOUTx available
DM365: Added PINMUX definitions for GPIO30..32
Davinci: iotable based ioremap() interception
Davinci: pinmux - use ioremap()
Davinci: aintc/cpintc - use ioremap()
Davinci: psc - use ioremap()
Davinci: timer - use ioremap()
Davinci: jtag_id - use ioremap()
Davinci: da8xx: rtc - use ioremap
Davinci: gpio - use ioremap()
davinci: edma: fix coding style issue related to breaking lines
davinci: edma: use BIT() wherever possible
davinci: edma: fix coding style issue related to usage of braces
davinci: edma: use a more intuitive name for edma_info
Davinci: serial - conditional reset via pwremu
Davinci: serial - use ioremap()
Davinci: serial - remove unnecessary define
Davinci: watchdog reset separation across socs
...
Fix up trivial conflict in arch/arm/Kconfig due to removal of "select
GENERIC_TIME"
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (224 commits)
ARM: remove 'select GENERIC_TIME'
ARM: 6136/1: ARCH_REQUIRE_GPIOLIB selects GENERIC_GPIO
ARM: 6074/1: oprofile: convert from sysdev to platform device
ARM: 6073/1: oprofile: remove old files and update KConfig
ARM: 6072/1: oprofile: use perf-events framework as backend
ARM: 6071/1: perf-events: allow modules to query the number of hardware counters
ARM: 6070/1: perf-events: add support for xscale PMUs
ARM: 6069/1: perf-events: use numeric ID to identify PMU
ARM: 6064/1: pmu: register IRQs at runtime
ARM: Optionally allow ARMv6 to use 'normal, bufferable' memory for DMA
ARM: 6134/1: Handle instruction cache maintenance fault properly
ARM: nwfpe: allow debugging output to be configured at runtime
ARM: rename mach_cpu_disable() to platform_cpu_disable()
ARM: 6132/1: PL330: Add common core driver
ARM: 6094/1: Extend cache-l2x0 to support the 16-way PL310
ARM: Move memory mapping into mmu.c
ARM: Ensure meminfo is sorted prior to sanity_check_meminfo
ARM: Remove useless linux/bootmem.h includes
ARM: convert /proc/cpu/aligment to seq_file
arm: use asm-generic/scatterlist.h
...
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (127 commits)
sh: update defconfigs.
sh: Fix up the NUMA build for recent LMB changes.
sh64: provide a stub per_cpu_trap_init() definition.
sh: fix up CONFIG_KEXEC=n build.
sh: fixup the docbook paths for clock framework shuffling.
driver core: Early dev_name() depends on slab_is_available().
sh: simplify WARN usage in SH clock driver
sh: Check return value of clk_get on ms7724
sh: Check return value of clk_get on ecovec24
sh: move sh clock-cpg.c contents to drivers/sh/clk-cpg.c
sh: move sh clock.c contents to drivers/sh/clk.
sh: move sh asm/clock.h contents to linux/sh_clk.h V2
sh: remove unused clock lookup
sh: switch boards to clkdev
sh: switch sh4-202 to clkdev
sh: switch shx3 to clkdev
sh: switch sh7757 to clkdev
sh: switch sh7763 to clkdev
sh: switch sh7780 to clkdev
sh: switch sh7786 to clkdev
...
Separate out ata_bmdma_qc_issue() from ata_sff_qc_issue() such that
ata_sff_qc_issue() only deals with non-BMDMA SFF protocols (PIO and
nodata) while ata_bmdma_qc_issue() deals with the BMDMA protocols and
uses ata_sff_qc_issue() for non-DMA commands. All the users are
updated accordingly.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
struct ata_prd and ap->prd are BMDMA specific. Add bmdma_ prefix to
them and move them inside CONFIG_ATA_SFF.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Both qc_prep functions deal only with BMDMA PRD setup and PIO only SFF
drivers don't need them. Rename to ata_bmdma_[dumb_]qc_prep() and
relocate.
All usages are renamed except for pdc_adma and sata_qstor. Those two
drivers are not BMDMA drivers and don't need to call BMDMA qc_prep
functions. Calls to ata_sff_qc_prep() in the two drivers are removed.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Some of error handling logic in ata_sff_error_handler() and all of
ata_sff_post_internal_cmd() are for BMDMA. Create
ata_bmdma_error_handler() and ata_bmdma_post_internal_cmd() and move
BMDMA part into those.
While at it, change DMA protocol check to ata_is_dma(), fix
post_internal_cmd to call ap->ops->bmdma_stop instead of directly
calling ata_bmdma_stop() and open code hardreset selection so that
ata_std_error_handler() doesn't have to know about sff hardreset.
As these two functions are BMDMA specific, there's no reason to check
for bmdma_addr before calling bmdma methods if the protocol of the
failed command is DMA. sata_mv and pata_mpc52xx now don't need to set
.post_internal_cmd to ATA_OP_NULL and pata_icside and sata_qstor don't
need to set it to their bmdma_stop routines.
ata_sff_post_internal_cmd() becomes noop and is removed.
This fixes p3 described in clean-up-BMDMA-initialization patch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
port_task is tightly bound to the standard SFF PIO HSM implementation.
Using it for any other purpose would be error-prone and there's no
such user and if some drivers need such feature, it would be much
better off using its own. Move it inside CONFIG_ATA_SFF and rename it
to sff_pio_task.
The only function which is exposed to the core layer is
ata_sff_flush_pio_task() which is renamed from ata_port_flush_task()
and now also takes care of resetting hsm_task_state to HSM_ST_IDLE,
which is possible as it's now specific to PIO HSM.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
ap->[last_]ctl are specific to SFF controllers. Put them inside
CONFIG_ATA_SFF and move initialization into ata_sff_port_init().
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Ralph Campbell
Linus Torvalds
Takashi Iwai
Lin Ming
Wolfram Sang
Uwe Kleine-König
Rabin Vincent
manjugk manjugk
Alexander Shishkin
Kalle Jokiniemi
Santosh Shilimkar
Sonic Zhang
Michael Hennerich
Mark Brown
Kevin Hilman
Dmitry Torokhov
Tejun Heo