Instead of prefetching all segment bases before emulation, read them at the
last moment. Since most of them are unneeded, we save some cycles on
Intel machines where this is a bit expensive.
Signed-off-by: Avi Kivity <avi@qumranet.com>
rip relative decoding is relative to the instruction pointer of the next
instruction; by moving address adjustment until after decoding is complete,
we remove the need to determine the instruction size.
Signed-off-by: Avi Kivity <avi@qumranet.com>
This patch enables coalesced MMIO for x86 architecture.
It defines KVM_MMIO_PAGE_OFFSET and KVM_CAP_COALESCED_MMIO.
It enables the compilation of coalesced_mmio.c.
Signed-off-by: Laurent Vivier <Laurent.Vivier@bull.net>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Prefixes functions that will be exported with kvm_.
We also prefixed set_segment() even if it still static
to be coherent.
signed-off-by: Guillaume Thouvenin <guillaume.thouvenin@ext.bull.net>
Signed-off-by: Laurent Vivier <laurent.vivier@bull.net>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Add emulation for the memory type range registers, needed by VMware esx 3.5,
and by pci device assignment.
Signed-off-by: Avi Kivity <avi@qumranet.com>
KVM turns off hardware virtualization extensions during reboot, in order
to disassociate the memory used by the virtualization extensions from the
processor, and in order to have the system in a consistent state.
Unfortunately virtual machines may still be running while this goes on,
and once virtualization extensions are turned off, any virtulization
instruction will #UD on execution.
Fix by adding an exception handler to virtualization instructions; if we get
an exception during reboot, we simply spin waiting for the reset to complete.
If it's a true exception, BUG() so we can have our stack trace.
Signed-off-by: Avi Kivity <avi@qumranet.com>
The KVM MMU tries to detect when a speculative pte update is not actually
used by demand fault, by checking the accessed bit of the shadow pte. If
the shadow pte has not been accessed, we deem that page table flooded and
remove the shadow page table, allowing further pte updates to proceed
without emulation.
However, if the pte itself points at a page table and only used for write
operations, the accessed bit will never be set since all access will happen
through the emulator.
This is exactly what happens with kscand on old (2.4.x) HIGHMEM kernels.
The kernel points a kmap_atomic() pte at a page table, and then
proceeds with read-modify-write operations to look at the dirty and accessed
bits. We get a false flood trigger on the kmap ptes, which results in the
mmu spending all its time setting up and tearing down shadows.
Fix by setting the shadow accessed bit on emulated accesses.
Signed-off-by: Avi Kivity <avi@qumranet.com>
To distinguish between real page faults and nested page faults they should be
traced as different events. This is implemented by this patch.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
random uvesafb failures were reported against Gentoo:
http://bugs.gentoo.org/show_bug.cgi?id=222799
and Mihai Moldovan bisected it back to:
> 8f4d37ec07 is first bad commit
> commit 8f4d37ec07
> Author: Peter Zijlstra <a.p.zijlstra@chello.nl>
> Date: Fri Jan 25 21:08:29 2008 +0100
>
> sched: high-res preemption tick
Linus suspected it to be hrtick + vm86 interaction and observed:
> Btw, Peter, Ingo: I think that commit is doing bad things. They aren't
> _incorrect_ per se, but they are definitely bad.
>
> Why?
>
> Using random _TIF_WORK_MASK flags is really impolite for doing
> "scheduling" work. There's a reason that arch/x86/kernel/entry_32.S
> special-cases the _TIF_NEED_RESCHED flag: we don't want to exit out of
> vm86 mode unnecessarily.
>
> See the "work_notifysig_v86" label, and how it does that
> "save_v86_state()" thing etc etc.
Right, I never liked having to fiddle with those TIF flags. Initially I
needed it because the hrtimer base lock could not nest in the rq lock.
That however is fixed these days.
Currently the only reason left to fiddle with the TIF flags is remote
wakeups. We cannot program a remote cpu's hrtimer. I've been thinking
about using the new and improved IPI function call stuff to implement
hrtimer_start_on().
However that does require that smp_call_function_single(.wait=0) works
from interrupt context - /me looks at the latest series from Jens - Yes
that does seem to be supported, good.
Here's a stab at cleaning this stuff up ...
Mihai reported test success as well.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Tested-by: Mihai Moldovan <ionic@ionic.de>
Cc: Michal Januszewski <spock@gentoo.org>
Cc: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
so NUMAQ can use that to call numaq_pre_time_init()
This allows us to remove a NUMAQ special from arch/x86/kernel/setup.c.
(and paves the way to remove the NUMAQ subarch)
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
add these new x86_quirks methods:
int *mpc_record;
int (*mpc_apic_id)(struct mpc_config_processor *m);
void (*mpc_oem_bus_info)(struct mpc_config_bus *m, char *name);
void (*mpc_oem_pci_bus)(struct mpc_config_bus *m);
void (*smp_read_mpc_oem)(struct mp_config_oemtable *oemtable,
unsigned short oemsize);
... and move NUMAQ related mps table handling to numaq_32.c.
also move the call to smp_read_mpc_oem() to smp_read_mpc() directly.
Should not change functionality, albeit it would be nice to get it
tested on real NUMAQ as well ...
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
introduce x86_quirks array of boot-time quirk methods.
No change in functionality intended.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
As 256 entries are needed, aligning to a 256-entry boundary is
sufficient and still guarantees the single pte table requirement.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
It's not used anywhere outside its single referencing file.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Declaring x86 traps under one hood.
Declaring x86 do_traps before defining them.
Signed-off-by: Jaswinder Singh <jaswinder@infradead.org>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Alexander van Heukelum <heukelum@fastmail.fm>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The force_mwait variable iss defined either in
arch/x86/kernel/cpu/amd.c or in arch/x86/kernel/setup_64.c, but it is
only initialized and used in arch/x86/kernel/process.c. This patch
moves the declaration to arch/x86/kernel/process.c.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: michael@free-electrons.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Fallout from commit 33185c504f ("x86:
merge signal_32/64.h")
Thanks to Dick Streefland who provided an useful testcase on
http://lkml.org/lkml/2008/3/17/205 (only applicable to 2.6.24.x), that
helped a lot as a deterministic way to bisect an issue that leaded to
this fix.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: Luiz Fernando N. Capitulino <lcapitulino@mandriva.com.br>
Cc: Roland McGrath <roland@redhat.com>
Cc: <stable@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Real-time code needs to know the number of cycles per second
on SGI UV. The information is provided via a run time BIOS
call. This patch provides the linux side of that interface.
This is the first of several run time BIOS calls to be defined
in uv/bios.h and bios_uv.c.
Note that BIOS_CALL() is just a stub for now. The bios
side is being worked on.
Signed-off-by: Russ Anderson <rja@sgi.com>
Cc: Jack Steiner <steiner@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Ricardo M. Correia spotted that the use of __fls() in fls64() did
not seem to make sense. In fact fls64()'s implementation is fine,
but the description of __fls() was wrong. Fix that.
Reported-by: "Ricardo M. Correia" <Ricardo.M.Correia@Sun.COM>
Signed-off-by: Alexander van Heukelum <heukelum@fastmail.fm>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andi Kleen <andi@firstfloor.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
[ mingo@elte.hu: picked up this patch from Maciej, lets make apic=debug
print out more info - we had a lot of APIC changes ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
As a microoptimisation, make apic_verbosity unsigned. This will make
apic_printk(APIC_QUIET, ...) expand into just printk(...) with the
surrounding condition and a reference to apic_verbosity removed.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
it's separate functionality that deserves its own file.
This also prepares 32-bit memtest support.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Use alternatives to select the workaround for the 11AP Pentium erratum
for the affected steppings on the fly rather than build time. Remove the
X86_GOOD_APIC configuration option and replace all the calls to
apic_write_around() with plain apic_write(), protecting accesses to the
ESR as appropriate due to the 3AP Pentium erratum. Remove
apic_read_around() and all its invocations altogether as not needed.
Remove apic_write_atomic() and all its implementing backends. The use of
ASM_OUTPUT2() is not strictly needed for input constraints, but I have
used it for readability's sake.
I had the feeling no one else was brave enough to do it, so I went ahead
and here it is. Verified by checking the generated assembly and tested
with both a 32-bit and a 64-bit configuration, also with the 11AP
"feature" forced on and verified with gdb on /proc/kcore to work as
expected (as an 11AP machines are quite hard to get hands on these days).
Some script complained about the use of "volatile", but apic_write() needs
it for the same reason and is effectively a replacement for writel(), so I
have disregarded it.
I am not sure what the policy wrt defconfig files is, they are generated
and there is risk of a conflict resulting from an unrelated change, so I
have left changes to them out. The option will get removed from them at
the next run.
Some testing with machines other than mine will be needed to avoid some
stupid mistake, but despite its volume, the change is not really that
intrusive, so I am fairly confident that because it works for me, it will
everywhere.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Merge the GDT_ENTRY() macro between arch/x86/boot/pm.c and
arch/x86/kernel/acpi/sleep.c and put the new one in
<asm-x86/segment.h>.
While we're at it, correct the bitmasks for the limit and flags. The
new version relies on using ULL constants in order to cause type
promotion rather than explicit casts; this avoids having to include
<linux/types.h> in <asm-x86/segments.h>.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: fix asm/e820.h for userspace inclusion
x86: fix numaq_tsc_disable
x86: fix kernel_physical_mapping_init() for large x86 systems
asm-x86/e820.h is included from userspace. 'x86: make e820.c to have
common functions' (b79cd8f126) broke it:
make -C Documentation/lguest
cc -Wall -Wmissing-declarations -Wmissing-prototypes -O3 -I../../include
lguest.c -lz -o lguest
In file included from ../../include/asm-x86/bootparam.h:8,
from lguest.c:45:
../../include/asm/e820.h:66: error: expected ‘)’ before ‘start’
../../include/asm/e820.h:67: error: expected ‘)’ before ‘start’
../../include/asm/e820.h:68: error: expected ‘)’ before ‘start’
../../include/asm/e820.h:72: error: expected ‘=’, ‘,’, ‘;’, ‘asm’
or ‘__attribute__’ before ‘e820_update_range’
...
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (72 commits)
Revert "x86/PCI: ACPI based PCI gap calculation"
PCI: remove unnecessary volatile in PCIe hotplug struct controller
x86/PCI: ACPI based PCI gap calculation
PCI: include linux/pm_wakeup.h for device_set_wakeup_capable
PCI PM: Fix pci_prepare_to_sleep
x86/PCI: Fix PCI config space for domains > 0
Fix acpi_pm_device_sleep_wake() by providing a stub for CONFIG_PM_SLEEP=n
PCI: Simplify PCI device PM code
PCI PM: Introduce pci_prepare_to_sleep and pci_back_from_sleep
PCI ACPI: Rework PCI handling of wake-up
ACPI: Introduce new device wakeup flag 'prepared'
ACPI: Introduce acpi_device_sleep_wake function
PCI: rework pci_set_power_state function to call platform first
PCI: Introduce platform_pci_power_manageable function
ACPI: Introduce acpi_bus_power_manageable function
PCI: make pci_name use dev_name
PCI: handle pci_name() being const
PCI: add stub for pci_set_consistent_dma_mask()
PCI: remove unused arch pcibios_update_resource() functions
PCI: fix pci_setup_device()'s sprinting into a const buffer
...
Fixed up conflicts in various files (arch/x86/kernel/setup_64.c,
arch/x86/pci/irq.c, arch/x86/pci/pci.h, drivers/acpi/sleep/main.c,
drivers/pci/pci.c, drivers/pci/pci.h, include/acpi/acpi_bus.h) from x86
and ACPI updates manually.
"idle=nomwait" disables the use of the MWAIT
instruction from both C1 (C1_FFH) and deeper (C2C3_FFH)
C-states.
When MWAIT is unavailable, the BIOS and OS generally
negotiate to use the HALT instruction for C1,
and use IO accesses for deeper C-states.
This option is useful for power and performance
comparisons, and also to work around BIOS bugs
where broken MWAIT support is advertised.
http://bugzilla.kernel.org/show_bug.cgi?id=10807http://bugzilla.kernel.org/show_bug.cgi?id=10914
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Li Shaohua <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
"idle=halt" limits the idle loop to using
the halt instruction. No MWAIT, no IO accesses,
no C-states deeper than C1.
If something is broken in the idle code,
"idle=halt" is a less severe workaround
than "idle=poll" which disables all power savings.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
This closes some arcane holes in single-step handling that can arise
only when user programs set TF directly (via popf or sigreturn) and
then use vDSO (syscall/sysenter) system call entry. In those entry
paths, the clear_TF_reenable case hits and we must check TIF_SINGLESTEP
to be sure our bookkeeping stays correct wrt the user's view of TF.
Signed-off-by: Roland McGrath <roland@redhat.com>
This unifies and cleans up the syscall tracing code on i386 and x86_64.
Using a single function for entry and exit tracing on 32-bit made the
do_syscall_trace() into some terrible spaghetti. The logic is clear and
simple using separate syscall_trace_enter() and syscall_trace_leave()
functions as on 64-bit.
The unification adds PTRACE_SYSEMU and PTRACE_SYSEMU_SINGLESTEP support
on x86_64, for 32-bit ptrace() callers and for 64-bit ptrace() callers
tracing either 32-bit or 64-bit tasks. It behaves just like 32-bit.
Changing syscall_trace_enter() to return the syscall number shortens
all the assembly paths, while adding the SYSEMU feature in a simple way.
Signed-off-by: Roland McGrath <roland@redhat.com>
This unifies the treatment of TIF_SINGLESTEP on i386 and x86_64.
The bit is now excluded from _TIF_WORK_MASK on i386 as it has been
on x86_64. This means the do_notify_resume() path using it is never
used, so TIF_SINGLESTEP is not cleared on returning to user mode.
Both now leave TIF_SINGLESTEP set when returning to user, so that
it's already set on an int $0x80 system call entry. This removes
the need for testing TF on the system_call path. Doing it this way
fixes the regression for PTRACE_SINGLESTEP into a sigreturn syscall,
introduced by commit 1e2e99f0e4.
The clear_TF_reenable case that sets TIF_SINGLESTEP can only happen
on a non-exception kernel entry, i.e. sysenter/syscall instruction.
That will always get to the syscall exit tracing path.
Signed-off-by: Roland McGrath <roland@redhat.com>
The standard ticket spinlocks are very expensive in a virtual
environment, because their performance depends on Xen's scheduler
giving vcpus time in the order that they're supposed to take the
spinlock.
This implements a Xen-specific spinlock, which should be much more
efficient.
The fast-path is essentially the old Linux-x86 locks, using a single
lock byte. The locker decrements the byte; if the result is 0, then
they have the lock. If the lock is negative, then locker must spin
until the lock is positive again.
When there's contention, the locker spin for 2^16[*] iterations waiting
to get the lock. If it fails to get the lock in that time, it adds
itself to the contention count in the lock and blocks on a per-cpu
event channel.
When unlocking the spinlock, the locker looks to see if there's anyone
blocked waiting for the lock by checking for a non-zero waiter count.
If there's a waiter, it traverses the per-cpu "lock_spinners"
variable, which contains which lock each CPU is waiting on. It picks
one CPU waiting on the lock and sends it an event to wake it up.
This allows efficient fast-path spinlock operation, while allowing
spinning vcpus to give up their processor time while waiting for a
contended lock.
[*] 2^16 iterations is threshold at which 98% locks have been taken
according to Thomas Friebel's Xen Summit talk "Preventing Guests from
Spinning Around". Therefore, we'd expect the lock and unlock slow
paths will only be entered 2% of the time.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Christoph Lameter <clameter@linux-foundation.org>
Cc: Petr Tesarik <ptesarik@suse.cz>
Cc: Virtualization <virtualization@lists.linux-foundation.org>
Cc: Xen devel <xen-devel@lists.xensource.com>
Cc: Thomas Friebel <thomas.friebel@amd.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Implement a version of the old spinlock algorithm, in which everyone
spins waiting for a lock byte. In order to be compatible with the
ticket-lock's use of a zero initializer, this uses the convention of
'0' for unlocked and '1' for locked.
This algorithm is much better than ticket locks in a virtual
envionment, because it doesn't interact badly with the vcpu scheduler.
If there are multiple vcpus spinning on a lock and the lock is
released, the next vcpu to be scheduled will take the lock, rather
than cycling around until the next ticketed vcpu gets it.
To use this, you must call paravirt_use_bytelocks() very early, before
any spinlocks have been taken.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Christoph Lameter <clameter@linux-foundation.org>
Cc: Petr Tesarik <ptesarik@suse.cz>
Cc: Virtualization <virtualization@lists.linux-foundation.org>
Cc: Xen devel <xen-devel@lists.xensource.com>
Cc: Thomas Friebel <thomas.friebel@amd.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Ticket spinlocks have absolutely ghastly worst-case performance
characteristics in a virtual environment. If there is any contention
for physical CPUs (ie, there are more runnable vcpus than cpus), then
ticket locks can cause the system to end up spending 90+% of its time
spinning.
The problem is that (v)cpus waiting on a ticket spinlock will be
granted access to the lock in strict order they got their tickets. If
the hypervisor scheduler doesn't give the vcpus time in that order,
they will burn timeslices waiting for the scheduler to give the right
vcpu some time. In the worst case it could take O(n^2) vcpu scheduler
timeslices for everyone waiting on the lock to get it, not counting
new cpus trying to take the lock while the log-jam is sorted out.
These hooks allow a paravirt backend to replace the spinlock
implementation.
At the very least, this could revert the implementation back to the
old lock algorithm, which allows the next scheduled vcpu to take the
lock, and has basically fairly good performance.
It also allows the spinlocks to take advantages of the hypervisor
features to make locks more efficient (spin and block, for example).
The cost to native execution is an extra direct call when using a
spinlock function. There's no overhead if CONFIG_PARAVIRT is turned
off.
The lock structure is fixed at a single "unsigned int", initialized to
zero, but the spinlock implementation can use it as it wishes.
Thanks to Thomas Friebel's Xen Summit talk "Preventing Guests from
Spinning Around" for pointing out this problem.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Christoph Lameter <clameter@linux-foundation.org>
Cc: Petr Tesarik <ptesarik@suse.cz>
Cc: Virtualization <virtualization@lists.linux-foundation.org>
Cc: Xen devel <xen-devel@lists.xensource.com>
Cc: Thomas Friebel <thomas.friebel@amd.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
AMD only supports "syscall" from 32-bit compat usermode.
Intel and Centaur(?) only support "sysenter" from 32-bit compat usermode.
Set the X86 feature bits accordingly, and set up the vdso in
accordance with those bits. On the offchance we run on in a 64-bit
environment which supports neither syscall nor sysenter from 32-bit
mode, then fall back to the int $0x80 vdso.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
The Xen hypercall interface is allowed to trash any or all of the
argument registers, so we need to be careful that the kernel state
isn't damaged. On 32-bit kernels, the hypercall parameter registers
same as a regparm function call, so we've got away without explicit
clobbering so far. The 64-bit ABI defines lots of caller-save
registers, so save them all for safety. We can trim this set later by
re-distributing the responsibility for saving all these registers.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Stephen Tweedie <sct@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
64-bit hypercall interface can pass a maddr in one argument rather
than splitting it.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Stephen Tweedie <sct@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Use callback_op hypercall to register callbacks in a 32/64-bit
independent way (64-bit doesn't need a code segment, but that detail
is hidden in XEN_CALLBACK).
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Stephen Tweedie <sct@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
When building initial pagetables in 64-bit kernel the pud/pmd pointer may
be in ioremap/fixmap space, so we need to walk the pagetable to look up the
physical address.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Stephen Tweedie <sct@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Set up the initial pagetables to map the kernel mapping into the
physical mapping space. This makes __va() usable, since it requires
physical mappings.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Stephen Tweedie <sct@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
As a stopgap until Mike Travis's x86-64 gs-based percpu patches are
ready, provide workaround functions for x86_read/write_percpu for
Xen's use.
Specifically, this means that we can't really make use of vcpu
placement, because we can't use a single gs-based memory access to get
to vcpu fields. So disable all that for now.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Stephen Tweedie <sct@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
We need extra pv_mmu_ops for 64-bit, to deal with the extra level of
pagetable.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Stephen Tweedie <sct@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The 64-bit calling convention for hypercalls uses different registers
from 32-bit. Annoyingly, gcc's asm syntax doesn't have a way to
specify one of the extra numeric reigisters in a constraint, so we
must use explicitly placed register variables. Given that we have to
do it for some args, may as well do it for all.
Also fix syntax gcc generates for the call instruction itself. We
need a plain direct call, but the asm expansion which works on 32-bit
generates a rip-relative addressing mode in 64-bit, which is treated
as an indirect call. The alternative is to pass the hypercall page
offset into the asm, and have it add it to the hypercall page start
address to generate the call.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Stephen Tweedie <sct@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
64-bit guests can pass 64-bit quantities in a single argument,
so fix up the hypercalls.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Stephen Tweedie <sct@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Copy 64-bit definitions of various interface structures into place.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Stephen Tweedie <sct@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This allows Xen's xen_cpu_up() to allocate a pda for the new CPU.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Stephen Tweedie <sct@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Call paravirt_pagetable_setup_{start,done}
These paravirt_ops functions were not being called on x86_64.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Stephen Tweedie <sct@redhat.com>
Cc: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
AS arch/x86/lib/csum-copy_64.o
arch/x86/lib/csum-copy_64.S: Assembler messages:
arch/x86/lib/csum-copy_64.S:48: Error: Macro `ignore' was already defined
make[1]: *** [arch/x86/lib/csum-copy_64.o] Error 1
make: *** [arch/x86/lib] Error 2
It appears that csum-copy_64.S and dwarf2.h both define an ignore macro.
I would expect one of them can be renamed quite easily, unless they
are references elsewhere.
Caused-by-commit: 392a0fc96b
x86: merge dwarf2 headers
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* Strengthen the return type for the _node_to_cpumask_ptr to be
a const pointer. This adds compiler checking to insure that
node_to_cpumask_map[] is not changed inadvertently.
Signed-off-by: Mike Travis <travis@sgi.com>
Cc: "akpm@linux-foundation.org" <akpm@linux-foundation.org>
Cc: Yinghai Lu <yhlu.kernel@gmail.com>
Acked-by: Vegard Nossum <vegard.nossum@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Now that IRQ2 is never made available to the I/O APIC, there is no need
to special-case it and mask as a workaround for broken systems. Actually,
because of the former, mask_IO_APIC_irq(2) is a no-op already.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Andreas Herrmann <andreas.herrmann3@amd.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
got this on a test-system:
calling numaq_tsc_disable+0x0/0x39
NUMAQ: disabling TSC
initcall numaq_tsc_disable+0x0/0x39 returned 0 after 0 msecs
that's because we should not be using arch_initcall to call numaq_tsc_disable.
need to call it in setup_arch before time_init()/tsc_init()
and call it in init_intel() to make the cpu feature bits right.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Fix size of LDT entries. On x86-64, ldt_desc is a double-sized descriptor.
Signed-off-by: Michael Karcher <kernel@mkarcher.dialup.fu-berlin.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
In dwarf2_32.h, test for CONFIG_AS_CFI instead of
CONFIG_UNWIND_INFO. Turns out that searching for UNWIND_INFO
returns no match in any Kconfig or Makefile, so we're really
just throwing everything away regarding dwarf frames for i386.
The test that generates CONFIG_AS_CFI does not have anything
x86_64-specific, and right now, checking V=1 builds shows me
that the flags is there anyway, although unused.
Signed-off-by: Glauber Costa <gcosta@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
In dwarf_64.h header, use the "ignore" macro the way
i386 does.
Signed-off-by: Glauber Costa <gcosta@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
i spent a fair amount of time chasing a 64-bit bootup crash that manifested
itself as bootup segfaults:
S10network[1825]: segfault at 7f3e2b5d16b8 ip 00000031108748c9 sp 00007fffb9c14c70 error 4 in libc-2.7.so[3110800000+14d000]
eventually causing init to die and panic the system:
Kernel panic - not syncing: Attempted to kill init!
Pid: 1, comm: init Not tainted 2.6.26-rc9-tip #13878
after a maratonic bisection session, the bad commit turned out to be:
| b7675791859075418199c7af86a116ea34eaf5bd is first bad commit
| commit b7675791859075418199c7af86a116ea34eaf5bd
| Author: Jeremy Fitzhardinge <jeremy@goop.org>
| Date: Wed Jun 25 00:19:00 2008 -0400
|
| x86: remove open-coded save/load segment operations
|
| This removes a pile of buggy open-coded implementations of savesegment
| and loadsegment.
after some more bisection of this patch itself, it turns out that what
makes the difference are the savesegment() changes to __switch_to().
Taking a look at this portion of arch/x86/kernel/process_64.o revealed
this crutial difference:
| good: 99c: 8c e0 mov %fs,%eax
| 99e: 89 45 cc mov %eax,-0x34(%rbp)
|
| bad: 99c: 8c 65 cc mov %fs,-0x34(%rbp)
which is due to:
| unsigned fsindex;
| - asm volatile("movl %%fs,%0" : "=r" (fsindex));
| + savesegment(fs, fsindex);
savesegment() is implemented as:
#define savesegment(seg, value) \
asm("mov %%" #seg ",%0":"=rm" (value) : : "memory")
note the "m" modifier - it allows GCC to generate the segment move
into a memory operand as well.
But regarding segment operands there's a subtle detail in the x86
instruction set: the above 16-bit moves are zero-extend, but only
if it goes to a register.
If it goes to a memory operand, -0x34(%rbp) in the above case, there's
no zero-extend to 32-bit and the instruction will only save 16 bits
instead of the intended 32-bit.
The other 16 bits is random data - which can cause problems when that
value is used later on.
The solution is to only allow segment operands to go to registers.
This fix allows my test-system to boot up without crashing.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Add pseudo-feature bits to describe whether the CPU supports sysenter
and/or syscall from ia32-compat userspace. This removes a hardcoded
test in vdso32-setup.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
As other IOMMUs do, this puts dummy pci_swiotlb_init() in swiotlb.h
and remove ifdef CONFIG_SWIOTLB in pci-dma.c.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Muli Ben-Yehuda <muli@il.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Our way to handle gart_* functions for CONFIG_GART_IOMMU and
!CONFIG_GART_IOMMU cases is inconsistent.
We have some dummy gart_* functions in !CONFIG_GART_IOMMU case and
also use ifdef CONFIG_GART_IOMMU tricks in pci-dma.c to call some
gart_* functions in only CONFIG_GART_IOMMU case.
This patch removes ifdef CONFIG_GART_IOMMU in pci-dma.c and always use
dummy gart_* functions in iommu.h.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Muli Ben-Yehuda <muli@il.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
gart.h has only GART-specific stuff. Only GART code needs it. Other
IOMMU stuff should include iommu.h instead of gart.h.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Muli Ben-Yehuda <muli@il.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
when more than 4g memory is installed, don't map the big hole below 4g.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
NR_IRQS: let VISWS be just a sub-case of the generic code.
This can create a somewhat larger irq_desc[] array if NR_CPUS is high
but that should not worry VisWS which has 4 CPUs at most.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
move the SGIVW definitions from setup_arch.h into its own header file.
preparation for turning VISWS into a generic PC architecture.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
move the include/asm-x86/mach-visws/ VISWS specific hardware
details include files into include/asm-x86/visws, to be used from
generic code.
No code changed.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
update asm-x86/mach-visws/mach_apicdef.h to the generic version.
This should work fine as VISWS has a standard local APIC and thus
its mach_apicdef.h copy is just an ancient version of the generic code.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
now that include/asm-x86/mach-visws/smpboot_hooks.h equals
to the default file in ../mach-default/smpboot_hooks.h, simply
include it instead of maintaining a copy.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
update include/asm-x86/mach-visws/smpboot_hooks.h to
include/asm-x86/mach-default/smpboot_hooks.h (the generic version).
this _should_ work, because VISWS sets skip_ioapic_setup, but it
should be tested on a real VISWS to make sure.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Allow the generic smpboot quirks code to be built with
ONFIG_X86_IO_APIC disabled. This way VISWS will be able
to use it as-is.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Ingo Molnar
Avi Kivity
Laurent Vivier
Guillaume Thouvenin
Sheng Yang
Joerg Roedel
Peter Zijlstra
Mike Travis
Yinghai Lu
Jan Beulich
Jaswinder Singh
Thomas Petazzoni
Herton Ronaldo Krzesinski
Russ Anderson
Alexander van Heukelum
Maciej W. Rozycki
Harvey Harrison
Sebastian Siewior
H. Peter Anvin
Linus Torvalds
Rusty Russell
Zhao Yakui
Roland McGrath
Jeremy Fitzhardinge
Eduardo Habkost
Kevin Winchester
Michael Karcher
Glauber Costa
FUJITA Tomonori