This makes it possible to enqueue frames also from atomic context which
is needed for example, when networking packets are sent over a
Thunderbolt cable.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A Thunderbolt service driver might need to check if there was an error
with the descriptor when in frame mode. We also add two Rx specific
error flags RING_DESC_CRC_ERROR and RING_DESC_BUFFER_OVERRUN.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These are used by Thunderbolt services to send and receive frames over
the high-speed DMA rings.
We also put the functions to tb_ namespace to make sure we do not
collide with others and add missing kernel-doc comments for the exported
functions.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When high-speed DMA paths are used to transfer arbitrary data over a
Thunderbolt link, DMA rings should be in frame mode instead of raw mode.
The latter is used by the control channel (ring 0). In frame mode each
data frame can hold up to 4kB payload.
This patch modifies the DMA ring code to allow configuring a ring to be
in frame mode by passing a new flag (RING_FLAG_FRAME) to the ring when
it is allocated. In addition there might be need to enable end-to-end
(E2E) workaround for the ring to prevent losing Rx frames in certain
situations. We add another flag (RING_FLAG_E2E) that can be used for
this purpose.
This code is based on the work done by Amir Levy and Michael Jamet.
Signed-off-by: Michael Jamet <michael.jamet@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This will keep the interrupt delivery rate reasonable. The value used
here (128 us) is a recommendation from the hardware people.
This code is based on the work done by Amir Levy and Michael Jamet.
Signed-off-by: Michael Jamet <michael.jamet@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When two hosts are connected over a Thunderbolt cable, there is a
protocol they can use to communicate capabilities supported by the host.
The discovery protocol uses automatically configured control channel
(ring 0) and is build on top of request/response transactions using
special XDomain primitives provided by the Thunderbolt base protocol.
The capabilities consists of a root directory block of basic properties
used for identification of the host, and then there can be zero or more
directories each describing a Thunderbolt service and its capabilities.
Once both sides have discovered what is supported the two hosts can
setup high-speed DMA paths and transfer data to the other side using
whatever protocol was agreed based on the properties. The software
protocol used to communicate which DMA paths to enable is service
specific.
This patch adds support for the XDomain discovery protocol to the
Thunderbolt bus. We model each remote host connection as a Linux XDomain
device. For each Thunderbolt service found supported on the XDomain
device, we create Linux Thunderbolt service device which Thunderbolt
service drivers can then bind to based on the protocol identification
information retrieved from the property directory describing the
service.
This code is based on the work done by Amir Levy and Michael Jamet.
Signed-off-by: Michael Jamet <michael.jamet@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A Thunderbolt service might need to find the physical port from a link
the cable is connected to. For instance networking driver uses this
information to generate MAC address according the Apple ThunderboltIP
protocol.
Move this function to thunderbolt.h and rename it to
tb_phy_port_from_link() to reflect the fact that it does not take switch
as parameter.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These are needed by Thunderbolt services so move them to thunderbolt.h
to make sure they are available outside of drivers/thunderbolt.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These will be needed by Thunderbolt services when sending and receiving
XDomain control messages. While there change TB_CFG_PKG_PREPARE_TO_SLEEP
value to be decimal in order to be consistent with other members.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Thunderbolt XDomain discovery protocol uses directories which contain
properties and other directories to exchange information about what
capabilities the remote host supports. This also includes identification
information like device ID and name.
This adds support for parsing and formatting these properties and
establishes an API drivers can use in addition to the core Thunderbolt
driver. This API is exposed in a new header: include/linux/thunderbolt.h.
This code is based on the work done by Amir Levy and Michael Jamet.
Signed-off-by: Michael Jamet <michael.jamet@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These messages are all 32-bit aligned and they should be packed without
the __packed attribute just fine. It also allows compiler to generate
better code on some architectures.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We will be using these when communicating XDomain discovery protocol
over Thunderbolt link but they might be useful for other drivers as
well.
Make them available through byteorder/generic.h.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Update the ACPICA code in the kernel to upstream revision 20170728
including:
* Alias operator handling update (Bob Moore).
* Deferred resolution of reference package elements (Bob Moore).
* Support for the _DMA method in walk resources (Bob Moore).
* Tables handling update and support for deferred table
verification (Lv Zheng).
* Update of SMMU models for IORT (Robin Murphy).
* Compiler and disassembler updates (Alex James, Erik Schmauss,
Ganapatrao Kulkarni, James Morse).
* Tools updates (Erik Schmauss, Lv Zheng).
* Assorted minor fixes and cleanups (Bob Moore, Kees Cook,
Lv Zheng, Shao Ming).
- Rework the initialization of non-wakeup GPEs with method handlers
in order to address a boot crash on some systems with Thunderbolt
devices connected at boot time where we miss an early hotplug
event due to a delay in GPE enabling (Rafael Wysocki).
- Rework the handling of PCI bridges when setting up ACPI-based
device wakeup in order to avoid disabling wakeup for bridges
prematurely (Rafael Wysocki).
- Consolidate Apple DMI checks throughout the tree, add support for
Apple device properties to the device properties framework and
use these properties for the handling of I2C and SPI devices on
Apple systems (Lukas Wunner).
- Add support for _DMA to the ACPI-based device properties lookup
code and make it possible to use the information from there to
configure DMA regions on ARM64 systems (Lorenzo Pieralisi).
- Fix several issues in the APEI code, add support for exporting
the BERT error region over sysfs and update APEI MAINTAINERS
entry with reviewers information (Borislav Petkov, Dongjiu Geng,
Loc Ho, Punit Agrawal, Tony Luck, Yazen Ghannam).
- Fix a potential initialization ordering issue in the ACPI EC
driver and clean it up somewhat (Lv Zheng).
- Update the ACPI SPCR driver to extend the existing XGENE 8250
workaround in it to a new platform (m400) and to work around
an Xgene UART clock issue (Graeme Gregory).
- Add a new utility function to the ACPI core to support using
ACPI OEM ID / OEM Table ID / Revision for system identification
in blacklisting or similar and switch over the existing code
already using this information to this new interface (Toshi Kani).
- Fix an xpower PMIC issue related to GPADC reads that always return
0 without extra pin manipulations (Hans de Goede).
- Add statements to print debug messages in a couple of places in
the ACPI core for easier diagnostics (Rafael Wysocki).
- Clean up the ACPI processor driver slightly (Colin Ian King,
Hanjun Guo).
- Clean up the ACPI x86 boot code somewhat (Andy Shevchenko).
- Add a quirk for Dell OptiPlex 9020M to the ACPI backlight
driver (Alex Hung).
- Assorted fixes, cleanups and updates related to ACPI (Amitoj Kaur
Chawla, Bhumika Goyal, Frank Rowand, Jean Delvare, Punit Agrawal,
Ronald Tschalär, Sumeet Pawnikar).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=6Ke9
-----END PGP SIGNATURE-----
Merge tag 'acpi-4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI updates from Rafael Wysocki:
"These include a usual ACPICA code update (this time to upstream
revision 20170728), a fix for a boot crash on some systems with
Thunderbolt devices connected at boot time, a rework of the handling
of PCI bridges when setting up device wakeup, new support for Apple
device properties, support for DMA configurations reported via ACPI on
ARM64, APEI-related updates, ACPI EC driver updates and assorted minor
modifications in several places.
Specifics:
- Update the ACPICA code in the kernel to upstream revision 20170728
including:
* Alias operator handling update (Bob Moore).
* Deferred resolution of reference package elements (Bob Moore).
* Support for the _DMA method in walk resources (Bob Moore).
* Tables handling update and support for deferred table
verification (Lv Zheng).
* Update of SMMU models for IORT (Robin Murphy).
* Compiler and disassembler updates (Alex James, Erik Schmauss,
Ganapatrao Kulkarni, James Morse).
* Tools updates (Erik Schmauss, Lv Zheng).
* Assorted minor fixes and cleanups (Bob Moore, Kees Cook, Lv
Zheng, Shao Ming).
- Rework the initialization of non-wakeup GPEs with method handlers
in order to address a boot crash on some systems with Thunderbolt
devices connected at boot time where we miss an early hotplug event
due to a delay in GPE enabling (Rafael Wysocki).
- Rework the handling of PCI bridges when setting up ACPI-based
device wakeup in order to avoid disabling wakeup for bridges
prematurely (Rafael Wysocki).
- Consolidate Apple DMI checks throughout the tree, add support for
Apple device properties to the device properties framework and use
these properties for the handling of I2C and SPI devices on Apple
systems (Lukas Wunner).
- Add support for _DMA to the ACPI-based device properties lookup
code and make it possible to use the information from there to
configure DMA regions on ARM64 systems (Lorenzo Pieralisi).
- Fix several issues in the APEI code, add support for exporting the
BERT error region over sysfs and update APEI MAINTAINERS entry with
reviewers information (Borislav Petkov, Dongjiu Geng, Loc Ho, Punit
Agrawal, Tony Luck, Yazen Ghannam).
- Fix a potential initialization ordering issue in the ACPI EC driver
and clean it up somewhat (Lv Zheng).
- Update the ACPI SPCR driver to extend the existing XGENE 8250
workaround in it to a new platform (m400) and to work around an
Xgene UART clock issue (Graeme Gregory).
- Add a new utility function to the ACPI core to support using ACPI
OEM ID / OEM Table ID / Revision for system identification in
blacklisting or similar and switch over the existing code already
using this information to this new interface (Toshi Kani).
- Fix an xpower PMIC issue related to GPADC reads that always return
0 without extra pin manipulations (Hans de Goede).
- Add statements to print debug messages in a couple of places in the
ACPI core for easier diagnostics (Rafael Wysocki).
- Clean up the ACPI processor driver slightly (Colin Ian King, Hanjun
Guo).
- Clean up the ACPI x86 boot code somewhat (Andy Shevchenko).
- Add a quirk for Dell OptiPlex 9020M to the ACPI backlight driver
(Alex Hung).
- Assorted fixes, cleanups and updates related to ACPI (Amitoj Kaur
Chawla, Bhumika Goyal, Frank Rowand, Jean Delvare, Punit Agrawal,
Ronald Tschalär, Sumeet Pawnikar)"
* tag 'acpi-4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (75 commits)
ACPI / APEI: Suppress message if HEST not present
intel_pstate: convert to use acpi_match_platform_list()
ACPI / blacklist: add acpi_match_platform_list()
ACPI, APEI, EINJ: Subtract any matching Register Region from Trigger resources
ACPI: make device_attribute const
ACPI / sysfs: Extend ACPI sysfs to provide access to boot error region
ACPI: APEI: fix the wrong iteration of generic error status block
ACPI / processor: make function acpi_processor_check_duplicates() static
ACPI / EC: Clean up EC GPE mask flag
ACPI: EC: Fix possible issues related to EC initialization order
ACPI / PM: Add debug statements to acpi_pm_notify_handler()
ACPI: Add debug statements to acpi_global_event_handler()
ACPI / scan: Enable GPEs before scanning the namespace
ACPICA: Make it possible to enable runtime GPEs earlier
ACPICA: Dispatch active GPEs at init time
ACPI: SPCR: work around clock issue on xgene UART
ACPI: SPCR: extend XGENE 8250 workaround to m400
ACPI / LPSS: Don't abort ACPI scan on missing mem resource
mailbox: pcc: Drop uninformative output during boot
ACPI/IORT: Add IORT named component memory address limits
...
There is a mistake here where we accidentally use sizeof(TB_CFG_PKG_RESET)
instead of just TB_CFG_PKG_RESET. The size of an int is 4 so it's the
same as TB_CFG_PKG_NOTIFY_ACK.
Fixes: d7f781bfdb ("thunderbolt: Rework control channel to be more reliable")
Reported-by: Colin King <colin.king@canonical.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: stable <stable@vger.kernel.org> # 4.13
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If secure authentication of a devices fails, either because the device
already has another key uploaded, or there is some other error sending
challenge to the device, and the user only wants to approve the device
just once (without a new key being uploaded to the device) the current
implementation does not allow this because the key cannot be cleared
once set even if we allow it to be changed.
Make this scenario possible and allow clearing the key by writing
empty string to the key sysfs file.
Signed-off-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Non-root user may read the key back after root wrote it there.
This removes read access to everyone but root.
Signed-off-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The key size is tested by hex2bin() already (as '\0' isn't an hex digit)
Suggested-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are two patches for 4.13-rc5.
One is a fix for a reported thunderbolt issue, and the other a fix for
an MEI driver issue. Both have been in linux-next with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWY+zfg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynOKQCfYPp20/4S/DRl/O9mtFG6+Iczmm8AnAnFUVrN
EHmUF2ipsm4FQ4iZSot3
=yLZO
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.13-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc fixes from Greg KH:
"Here are two patches for 4.13-rc5.
One is a fix for a reported thunderbolt issue, and the other a fix for
an MEI driver issue. Both have been in linux-next with no reported
issues"
* tag 'char-misc-4.13-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
thunderbolt: Do not enumerate more ports from DROM than the controller has
mei: exclude device from suspend direct complete optimization
We're about to amend ACPI bus scan with DMI checks whether we're running
on a Mac to support Apple device properties in AML. The DMI checks are
performed for every single device, adding overhead for everything x86
that isn't Apple, which is the majority. Rafael and Andy therefore
request to perform the DMI match only once and cache the result.
Outside of ACPI various other Apple DMI checks exist and it seems
reasonable to use the cached value there as well. Rafael, Andy and
Darren suggest performing the DMI check in arch code and making it
available with a header in include/linux/platform_data/x86/.
To this end, add early_platform_quirks() to arch/x86/kernel/quirks.c
to perform the DMI check and invoke it from setup_arch(). Switch over
all existing Apple DMI checks, thereby fixing two deficiencies:
* They are now #defined to false on non-x86 arches and can thus be
optimized away if they're located in cross-arch code.
* Some of them only match "Apple Inc." but not "Apple Computer, Inc.",
which is used by BIOSes released between January 2006 (when the first
x86 Macs started shipping) and January 2007 (when the company name
changed upon introduction of the iPhone).
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Suggested-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Suggested-by: Darren Hart <dvhart@infradead.org>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
On one of my test machines nhi_mailbox_cmd() called from icm_suspend()
times out and returnes an error which then is propagated to the
caller and causes the entire system suspend to be aborted which isn't
very useful.
Instead of aborting system suspend, print the error into the log
and continue.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Michael Jamet <michael.jamet@intel.com>
- add a missing "!" in the uuid tests
- remove the last remaining user of the uuid_be type, and then
the type and its helpers
-----BEGIN PGP SIGNATURE-----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=FeA7
-----END PGP SIGNATURE-----
Merge tag 'uuid-for-4.13-2' of git://git.infradead.org/users/hch/uuid
Pull uuid fixes from Christoph Hellwig:
- add a missing "!" in the uuid tests
- remove the last remaining user of the uuid_be type, and then the type
and its helpers
* tag 'uuid-for-4.13-2' of git://git.infradead.org/users/hch/uuid:
uuid: remove uuid_be
thunderbolt: use uuid_t instead of uuid_be
uuid: fix incorrect uuid_equal conversion in test_uuid_test
Switch thunderbolt to the new uuid type.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Amir Goldstein <amir73il@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Firmware upgrade tools that decide which NVM image should be uploaded to
the Thunderbolt controller need to access active parts of the NVM even
if they are not run as root. The information in active NVM is not
considered security critical so we can use the default permissions set
by the NVMem framework.
Writing the NVM image is still left as root only operation.
While there mark the active NVM as read-only in the filesystem.
Reported-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Trivial fix to spelling mistake in tb_sw_warn warning message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Starting from Intel Falcon Ridge the NVM firmware can be upgraded by
using DMA configuration based mailbox commands. If we detect that the
host or device (device support starts from Intel Alpine Ridge) has the
DMA configuration based mailbox we expose NVM information to the
userspace as two separate Linux NVMem devices: nvm_active and
nvm_non_active. The former is read-only portion of the active NVM which
firmware upgrade tools can be use to find out suitable NVM image if the
device identification strings are not enough.
The latter is write-only portion where the new NVM image is to be
written by the userspace. It is up to the userspace to find out right
NVM image (the kernel does very minimal validation). The ICM firmware
itself authenticates the new NVM firmware and fails the operation if it
is not what is expected.
We also expose two new sysfs files per each switch: nvm_version and
nvm_authenticate which can be used to read the active NVM version and
start the upgrade process.
We also introduce safe mode which is the mode a switch goes when it does
not have properly authenticated firmware. In this mode the switch only
accepts a couple of commands including flashing a new NVM firmware image
and triggering power cycle.
This code is based on the work done by Amir Levy and Michael Jamet.
Signed-off-by: Michael Jamet <michael.jamet@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Starting from Intel Falcon Ridge the internal connection manager running
on the Thunderbolt host controller has been supporting 4 security
levels. One reason for this is to prevent DMA attacks and only allow
connecting devices the user trusts.
The internal connection manager (ICM) is the preferred way of connecting
Thunderbolt devices over software only implementation typically used on
Macs. The driver communicates with ICM using special Thunderbolt ring 0
(control channel) messages. In order to handle these messages we add
support for the ICM messages to the control channel.
The security levels are as follows:
none - No security, all tunnels are created automatically
user - User needs to approve the device before tunnels are created
secure - User need to approve the device before tunnels are created.
The device is sent a challenge on future connects to be able
to verify it is actually the approved device.
dponly - Only Display Port and USB tunnels can be created and those
are created automatically.
The security levels are typically configurable from the system BIOS and
by default it is set to "user" on many systems.
In this patch each Thunderbolt device will have either one or two new
sysfs attributes: authorized and key. The latter appears for devices
that support secure connect.
In order to identify the device the user can read identication
information, including UUID and name of the device from sysfs and based
on that make a decision to authorize the device. The device is
authorized by simply writing 1 to the "authorized" sysfs attribute. This
is following the USB bus device authorization mechanism. The secure
connect requires an additional challenge step (writing 2 to the
"authorized" attribute) in future connects when the key has already been
stored to the NVM of the device.
Non-ICM systems (before Alpine Ridge) continue to use the existing
functionality and the security level is set to none. For systems with
Alpine Ridge, even on Apple hardware, we will use ICM.
This code is based on the work done by Amir Levy and Michael Jamet.
Signed-off-by: Michael Jamet <michael.jamet@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On PCs the NHI host controller is only present when there is a device
connected. When the last device is disconnected the host controller will
dissappear shortly (within 10s). Now if that happens when we are
suspended we should not try to touch the hardware anymore, so add a flag
for this and check it before we re-enable rings.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The DMA (NHI) port of a switch provides access to the NVM of the host
controller (and devices starting from Intel Alpine Ridge). The NVM
contains also more complete DROM for the root switch including vendor
and device identification strings.
This will look for the DMA port capability for each switch and if found
populates sw->dma_port. We then teach tb_drom_read() to read the DROM
information from NVM if available for the root switch.
The DMA port capability also supports upgrading the NVM for both host
controller and devices which will be added in subsequent patches.
This code is based on the work done by Amir Levy and Michael Jamet.
Signed-off-by: Michael Jamet <michael.jamet@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In some cases it is useful to know what is the Thunderbolt generation
the switch supports. This introduces a new field to struct switch that
stores the generation of the switch based on the device ID. Unknown
switches (there should be none) are assumed to be first generation to be
on the safe side.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The host controller includes two sets of registers that are used to
communicate with the firmware. Add functions that can be used to access
these registers.
This code is based on the work done by Amir Levy and Michael Jamet.
Signed-off-by: Michael Jamet <michael.jamet@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add Intel Win Ridge (Thunderbolt 2) and Alpine Ridge (Thunderbolt 3)
controller PCI IDs to the list of supported devices.
This code is based on the work done by Amir Levy and Michael Jamet.
Signed-off-by: Michael Jamet <michael.jamet@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a request times out the response might arrive right after the request
is failed. This response is pushed to the kfifo and next request will
read it instead. Since it most likely will not pass our validation
checks in parse_header() the next request will fail as well, and
response to that request will be pushed to the kfifo, ad infinitum.
We end up in a situation where all requests fail and no devices can be
added anymore until the driver is unloaded and reloaded again.
To overcome this, rework the control channel so that we will have a
queue of outstanding requests. Each request will be handled in turn and
the response is validated against what is expected. Unexpected packets
(for example responses for requests that have been timed out) are
dropped. This model is copied from Greybus implementation with small
changes here and there to get it cope with Thunderbolt control packets.
In addition the configuration packets support sequence number which the
switch is supposed to copy from the request to response. We use this to
drop responses that are already timed out. Taking advantage of the
sequence number, we automatically retry configuration read/write 4 times
before giving up.
Also timeout is not a programming error so there is no need to trigger a
scary backtrace (WARN), instead we just log a warning. After all
Thunderbolt devices are hot-pluggable by definition which means user can
unplug a device any time and that is totally acceptable.
With this change there is no need to take the global domain lock when
sending configuration packets anymore. This is useful when we add
support for cross-domain (XDomain) communication later on.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the control channel (ctl.c) handles the one supported
notification (PLUG_EVENT) and sends back ACK accordingly. However, we
are going to add support for the internal connection manager (ICM) that
needs to handle a different notifications. So instead of dealing
everything in the control channel, we change the callback to take an
arbitrary thunderbolt packet and convert the native connection manager
to handle the event itself.
In addition we only push replies we know of to the response FIFO.
Everything else is treated as notification (or request) and is expected
to be dealt by the connection manager implementation.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We will be using this function in files introduced in subsequent
patches. While there the function is renamed to tb_cfg_make_header()
following tb_cfg_get_route().
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We are going to use it when we change the connection manager to handle
events itself. Also rename it to follow naming convention used in
functions exposed in ctl.h.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We will be forwarding notifications received from the control channel to
the connection manager implementations. This way they can decide what to
do if anything when a notification is received.
To be able to use control channel messages from other files, move them
to tb_msgs.h.
No functional changes intended.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The device DROM contains name of the vendor and device among other
things. Extract this information and expose it to the userspace via two
new attributes.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently tb_drom_parse_entry() is only able to parse drom entries of
type TB_DROM_ENTRY_PORT. Rename it to tb_drom_parse_entry_port().
Fold tb_drom_parse_port_entry() into it.
Its return value is currently ignored. Evaluate it and abort parsing on
error.
Change tb_drom_parse_entries() to accommodate for parsing of other entry
types than TB_DROM_ENTRY_PORT.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are devices out there where CRC32 of the DROM is not correct. One
reason for this is that the ICM firmware does not validate it and it
seems that neither does the Apple driver. To be able to support such
devices we continue parsing the DROM contents regardless of whether
CRC32 failed or not. We still keep the warning there.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All non-root switches are expected to have DROM so if the operation
fails, it might be due the user unlugging the device. There is no point
continuing adding the switch further in that case. Just bail out.
For root switches (hosts) the DROM is either retrieved from a EFI
variable, NVM or hard-coded.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Thunderbolt domain consists of switches that are connected to each
other, forming a bus. This will convert each switch into a real Linux
device structure and adds them to the domain. The advantage here is
that we get all the goodies from the driver core, like reference
counting and sysfs hierarchy for free.
Also expose device identification information to the userspace via new
sysfs attributes.
In order to support internal connection manager (ICM) we separate switch
configuration into its own function (tb_switch_configure()) which is
only called by the existing native connection manager implementation
used on Macs.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Thunderbolt fabric consists of one or more switches. This fabric is
called domain and it is controlled by an entity called connection
manager. The connection manager can be either internal (driven by a
firmware running on the host controller) or external (software driver).
This driver currently implements support for the latter.
In order to manage switches and their properties more easily we model
this domain structure as a Linux bus. Each host controller adds a domain
device to this bus, and these devices are named as domainN where N
stands for index or id of the current domain.
We then abstract connection manager specific operations into a new
structure tb_cm_ops and convert the existing tb.c to fill those
accordingly. This makes it easier to add support for the internal
connection manager in subsequent patches.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Following the usual pattern used in many places, we allow passing NULL
pointer to tb_ctl_free(). Then the user can call the function regardless
if it has allocated control channel or not making the code bit simpler.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Organization of the capabilities in switches and ports is not so random
after all. Rework the capability handling functionality so that it
follows how capabilities are organized and provide two new functions
(tb_switch_find_vse_cap() and tb_port_find_cap()) which can be used to
extract capabilities for ports and switches. Then convert the current
users over these.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Intel Thunderbolt controllers support up to 16 MSI-X vectors. Using
MSI-X is preferred over MSI or legacy interrupt and may bring additional
performance because there is no need to check the status registers which
interrupt was triggered.
While there we convert comments in structs tb_ring and tb_nhi to follow
kernel-doc format more closely.
This code is based on the work done by Amir Levy and Michael Jamet.
Signed-off-by: Michael Jamet <michael.jamet@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DROM version 2 is compatible with the previous generation so no need to
warn about that.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At least Falcon Ridge when in host mode does not have any kind of DROM
available and reading DROM offset returns 0 for these. Do not try to
read DROM any further in that case.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The root switch is part of the host controller and cannot be physically
removed, so there is no point of reading UID again on resume in order to
check if the root switch is still the same.
Suggested-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These functions should not (and do not) modify the argument in any way
so make it const.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here's the big char/misc driver patches for 4.10-rc1. Lots of tiny
changes over lots of "minor" driver subsystems, the largest being some
new FPGA drivers. Other than that, a few other new drivers, but no new
driver subsystems added for this kernel cycle, a nice change.
All of these have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWFAtwA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykyCgCeJn36u1AsBi7qZ3u/1hwD8k56s2IAnRo6U31r
WW65YcNTK7qYXqNbfgIa
=/t/V
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here's the big char/misc driver patches for 4.10-rc1. Lots of tiny
changes over lots of "minor" driver subsystems, the largest being some
new FPGA drivers. Other than that, a few other new drivers, but no new
driver subsystems added for this kernel cycle, a nice change.
All of these have been in linux-next with no reported issues"
* tag 'char-misc-4.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (107 commits)
uio-hv-generic: store physical addresses instead of virtual
Tools: hv: kvp: configurable external scripts path
uio-hv-generic: new userspace i/o driver for VMBus
vmbus: add support for dynamic device id's
hv: change clockevents unbind tactics
hv: acquire vmbus_connection.channel_mutex in vmbus_free_channels()
hyperv: Fix spelling of HV_UNKOWN
mei: bus: enable non-blocking RX
mei: fix the back to back interrupt handling
mei: synchronize irq before initiating a reset.
VME: Remove shutdown entry from vme_driver
auxdisplay: ht16k33: select framebuffer helper modules
MAINTAINERS: add git url for fpga
fpga: Clarify how write_init works streaming modes
fpga zynq: Fix incorrect ISR state on bootup
fpga zynq: Remove priv->dev
fpga zynq: Add missing \n to messages
fpga: Add COMPILE_TEST to all drivers
uio: pruss: add clk_disable()
char/pcmcia: add some error checking in scr24x_read()
...
So far Thunderbolt is (unfortunately) an Intel proprietary technology
that is only available on x86, so compiling on other arches is pointless
except for testing purposes. Amend Kconfig accordingly.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: Andreas Noever <andreas.noever@gmail.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Link: http://lkml.kernel.org/r/7dfda728d3ee8a33c80c49b224da7359c6015eea.1479456179.git.lukas@wunner.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Since commit c9cc3aaa02 ("thunderbolt: Use Device ROM retrieved from
EFI"), the THUNDERBOLT config option selects APPLE_PROPERTIES.
This broke the build for certain configs because APPLE_PROPERTIES is
located in a menu which depends on EFI: If EFI is not enabled, the
prerequisites needed for APPLE_PROPERTIES are not selected: Those are
EFI_DEV_PATH_PARSER and UCS2_STRING. Additionally EFI_DEV_PATH_PARSER
won't compile unless ACPI is enabled.
Commit 79f9cd35b0 ("thunderbolt, efi: Fix Kconfig dependencies")
sought to fix the breakage by making THUNDERBOLT select APPLE_PROPERTIES
only if EFI_STUB is enabled. On x86, EFI_STUB depends on EFI and EFI
depends on ACPI, so this fixed the build at least on this architecture.
However on arm and arm64, EFI_STUB does not depend on EFI, so once again
the prerequisites needed for APPLE_PROPERTIES are not selected.
Additionally ACPI is not available on arm and optional on arm64,
therefore EFI_DEV_PATH_PARSER won't compile.
Fix by selecting APPLE_PROPERTIES only on x86.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: Andreas Noever <andreas.noever@gmail.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Link: http://lkml.kernel.org/r/5c241cf92eb1dc2421218c1204c6a9d22c9f847b.1479456179.git.lukas@wunner.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Fix this EFI build failure on certain (rand)configs:
drivers/firmware/efi/apple-properties.c:149:9: error: implicit declaration of function ???efi_get_device_by_path??? [-Werror=implicit-function-declaration]
which is due to:
warning: (THUNDERBOLT) selects APPLE_PROPERTIES which has unmet direct dependencies (EFI && EFI_STUB && X86)
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Andreas Noever <andreas.noever@gmail.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Pedro Vilaça <reverser@put.as>
Cc: Peter Jones <pjones@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Pierre Moreau <pierre.morrow@free.fr> [MacBookPro11,3]
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Link: http://lkml.kernel.org/r/20161114151033.GA10141@wunner.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Macs with Thunderbolt 1 do not have a unit-specific DROM: The DROM is
empty with uid 0x1000000000000. (Apple started factory-burning a unit-
specific DROM with Thunderbolt 2.)
Instead, the NHI EFI driver supplies a DROM in a device property. Use
it if available. It's only available when booting with the efistub.
If it's not available, silently fall back to our hardcoded DROM.
The size of the DROM is always 256 bytes. The number is hardcoded into
the NHI EFI driver. This commit can deal with an arbitrary size however,
just in case they ever change that.
Background information: The EFI firmware volume contains ROM files for
the NHI, GMUX and several other chips as well as key material. This
strategy allows Apple to deploy ROM or key updates by simply publishing
an EFI firmware update on their website. Drivers do not access those
files directly but rather through a file server via EFI protocol
AC5E4829-A8FD-440B-AF33-9FFE013B12D8. Files are identified by GUID, the
NHI DROM has 339370BD-CFC6-4454-8EF7-704653120818.
The NHI EFI driver amends that file with a unit-specific uid. The uid
has 64 bit but its entropy is much lower: 24 bit represent the model,
24 bit are taken from a serial number, 16 bit are fixed. The NHI EFI
driver obtains the serial number via the DataHub protocol, copies it
into the DROM, calculates the CRC and submits the result as a device
property.
A modification is needed in the resume code where we currently read the
uid of all switches in the hierarchy to detect plug events that occurred
during sleep. On Thunderbolt 1 root switches this will now lead to a
mismatch between the uid of the empty DROM and the EFI DROM. Exempt the
root switch from this check: It's built in, so the uid should never
change. However we continue to *read* the uid of the root switch, this
seems like a good way to test its reachability after resume.
Tested-by: Lukas Wunner <lukas@wunner.de> [MacBookPro9,1]
Tested-by: Pierre Moreau <pierre.morrow@free.fr> [MacBookPro11,3]
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
Acked-by: Andreas Noever <andreas.noever@gmail.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Pedro Vilaça <reverser@put.as>
Cc: Peter Jones <pjones@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Link: http://lkml.kernel.org/r/20161112213237.8804-10-matt@codeblueprint.co.uk
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This first patch updates the NHI Thunderbolt controller registers file to
reflect that it is not only for Cactus Ridge.
No functional change intended.
Signed-off-by: Amir Levy <amir.jer.levy@intel.com>
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Falcon Ridge 4C has been supported by the driver from the beginning,
Falcon Ridge 2C support was just added. Don't irritate users with a
warning declaring the opposite.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
From: Xavier Gnata <xavier.gnata@gmail.com>
Add support to INTEL_FALCON_RIDGE_2C controller and corresponding quirk
to support suspend/resume.
Tested against 4.7 master on a MacBook Air 11" 2015.
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If tb_drom_read() fails, sw->drom is freed but not set to NULL. sw->drom
is then freed again in the error path of tb_switch_alloc().
The bug can be triggered by unplugging a thunderbolt device shortly after
it is detected by the thunderbolt driver.
Clear sw->drom if tb_drom_read() fails.
[bhelgaas: add Fixes:, stable versions of interest]
Fixes: 343fcb8c70 ("thunderbolt: Fix nontrivial endpoint devices.")
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v3.17+
CC: Lukas Wunner <lukas@wunner.de>
Add support for the 1st gen Light Ridge controller, which is built into
these systems:
iMac12,1 2011 21.5"
iMac12,2 2011 27"
Macmini5,1 2011 i5 2.3 GHz
Macmini5,2 2011 i5 2.5 GHz
Macmini5,3 2011 i7 2.0 GHz
MacBookPro8,1 2011 13"
MacBookPro8,2 2011 15"
MacBookPro8,3 2011 17"
MacBookPro9,1 2012 15"
MacBookPro9,2 2012 13"
Light Ridge (CV82524) was the very first copper Thunderbolt controller,
introduced 2010 alongside its fiber-optic cousin Light Peak (CVL2510).
Consequently the chip suffers from some teething troubles:
- MSI is broken for hotplug signaling on the downstream bridges: The chip
just never sends an interrupt. It requests 32 MSIs for each of its six
bridges and the pcieport driver only allocates one per bridge. However
I've verified that even if 32 MSIs are allocated there's no interrupt
on hotplug. The only option is thus to disable MSI, which is also what
OS X does. Apparently all Thunderbolt chips up to revision 1 of Cactus
Ridge 4C are plagued by this issue so quirk those as well.
- The chip supports a maximum hop_count of 32, unlike its successors
which support only 12. Fixup ring_interrupt_active() to cope with
values >= 32.
- Another peculiarity is that the chip supports a maximum of 13 ports
whereas its successors support 12. However the additional port (#5)
seems to be unusable as reading its TB_CFG_PORT config space results in
TB_CFG_ERROR_INVALID_CONFIG_SPACE. Add a quirk to mark the port
disabled on the root switch, assuming that's necessary on all Macs
using this chip.
Tested-by: Lukas Wunner <lukas@wunner.de> [MacBookPro9,1]
Tested-by: William Brown <william@blackhats.net.au> [MacBookPro8,2]
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Andreas Noever <andreas.noever@gmail.com>
Fix typo in tb_cfg_print_error() message. Fix bytecount in struct
tb_drom_entry_port comment. Replace magic number in tb_switch_alloc().
Rename tb_sw_set_unpplugged() and TB_CAL_IECS to fix typos.
[bhelgaas: no functional change intended]
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Andreas Noever <andreas.noever@gmail.com>
Intel Gen 1 and 2 chips use the same ID for NHI, bridges and switch. Gen 3
chips and onward use a distinct ID for the NHI.
No functional change intended.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Andreas Noever <andreas.noever@gmail.com>
The pci device ids listed in the thunderbolt driver are to restrictive,
which prevents the driver from being loaded on recent Apple MacBooks
using a thunderbolt 2 controller. In particular this prevented any
hot-plugging functionality for thunderbolt based ethernet dongles
(i.e. Apples thunderbolt gigabit ethernet broadcom tg3 based dongle
Model A1433 EMC 2590).
Changing the subvendor and subdevice to PCI_ANY_ID the thunderbolt driver
loads and binds to the pci device 07:00.0 System peripheral:
Intel Corporation Device 156c which is the thunderbolt 2 controller on
the MacBookPro12,1.
Successfully tested on MacBookPro12,1. With the patch the thunderbolt
module gets now loaded on boot. And it provides hot-plugging support both
for a cold-plugged and a warm-plugged ethernet dongle.
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Acked-by: Knuth Posern <knuth@posern.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Zero hops in tb_path_activate before writing a new path.
This fixes the following scenario:
- Boot with a coldplugged device
- Unplug device
- Plug device back in
- PCI hotplug fails
The hotplug operation fails because our new path matches the (now
defunct) path which was setup by the firmware for the coldplugged
device. By writing zeros before writing our path configuration we can
force thunderbolt to retrain the path.
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The advantage of kcalloc is, that will prevent integer overflows
which could result from the multiplication of number of elements
and size and it is also a bit nicer to read.
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Acked-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
nhi->rx_rings does not have type as struct tb_ring *, as it is a
double pointer so the elements of the array should have pointer type,
not structure type.
The Coccinelle semantic patch that makes this change is as follows:
// <smpl>
@disable sizeof_type_expr@
type T;
T **x;
@@
x =
<+...sizeof(
- T
+ *x
)...+>
// </smpl>
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Cc: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We use __crc32c_le in ctl.c. So make sure that the dependency is there.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tb_eeprom_get_drom_offset is local to this file.
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Force enum tb_drom_entry_type to unsigned to fix the following error:
drivers/thunderbolt/eeprom.c:202:39: error: dubious one-bit signed bitfield
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tb_find_cap in cap.c takes an enum tb_cap and not an u32. Fix the
declaration in tb.h.
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Thunderbolt packets are big endian. Cast pkg->buffer to __be32* when
accessing the checksum.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The result of "sizeof(struct tb_drom_entry_port)" is a size_t, which
is not necessarily the same as 'long', so we should use the appropriate
%z format string instead of %l.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The thunderbolt drivers cannot be built if CONFIG_PCI is disabled,
better add an explicit Kconfig dependency.
The "default no" line is redundant and can be removed at the same
time.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
'nhi_ids' is local to this file.
Signed-off-by: Sachin Kamat <sachin.kamat@samsung.com>
Acked-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
'descriptors' is a pointer. Use NULL isntead of 0.
Signed-off-by: Sachin Kamat <sachin.kamat@samsung.com>
Acked-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function returns a pointer. Hence return NULL instead of 0.
Signed-off-by: Sachin Kamat <sachin.kamat@samsung.com>
Acked-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function returns a pointer. Hence return NULL instead of 0.
Signed-off-by: Sachin Kamat <sachin.kamat@samsung.com>
Acked-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix issues observed with the Startech docking station:
Fix the type of the route parameter in tb_ctl_rx. It should be u64 and not
u8 (which only worked for short routes).
A thunderbolt cable contains two lanes. If both endpoints support it a
connection will be established on both lanes. Previously we tried to
scan below both "dual link ports". Use the information extracted from
the drom to only scan behind ports with lane_nr == 0.
Endpoints with more complex thunderbolt controllers have some of their
ports disabled (for example the NHI port or one of the HDMI/DP ports).
Accessing them results in an error so we now ignore ports which are
marked as disabled in the drom.
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All Thunderbolt switches (except the root switch) contain a drom which
contains information about the device. Right now we only read the UID.
Add code to read and parse this drom. For now we are only interested in
which ports are disabled and which ports are "dual link ports" (a
physical thunderbolt port/socket contains two such ports).
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We use _noirq since we have to restore the pci tunnels before the pci
core wakes the tunneled devices.
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add eeprom access code and read the uid during switch initialization.
The UID will be used to check device identity after suspend.
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A pci downstream and pci upstream port can be connected through a
tunnel. To establish the tunnel we have to setup two unidirectional
paths between the two ports.
Right now we only support paths with two hops (i.e. no chaining) and at
most one pci device per thunderbolt device.
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A thunderbolt path is a unidirectional channel between two thunderbolt
ports. Two such paths are needed to establish a pci tunnel.
This patch introduces struct tb_path as well as a set of tb_path_*
methods which are used to activate & deactivate paths.
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We receive a plug event callback whenever a thunderbolt device is added
or removed. This patch fills in the tb_handle_hotplug method and starts
reacting to these events by adding/removing switches from the hierarchy.
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Thunderbolt switches have a plug events capability. This patch adds the
tb_plug_events_active method and uses it to activate plug events during
switch allocation.
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Thunderbolt config areas contain capability lists similar to those found
on pci devices. This patch introduces a tb_find_cap utility method to
search for capabilities.
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds the structures tb_switch and tb_port as well as code to
initialize the root switch.
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Every thunderbolt device consists (logically) of a switch with multiple
ports. Every port contains up to four config regions (HOPS, PORT,
SWITCH, COUNTERS) which are used to configure the device.
The tb_regs.h file contains all known registers and capabilities from
these config regions.
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add struct tb which will contain our view of the thunderbolt bus. For
now it just contains a pointer to the control channel and a workqueue
for hotplug events.
Add thunderbolt_alloc_and_start() and thunderbolt_shutdown_and_free()
which are responsible for setup and teardown of struct tb.
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Thunderbolt devices are configured by reading/writing into their
configuration space (similar to pci). This is done by sending packets
through the NHI (native host interface) onto the control channel.
This patch handles the low level packet based protocol and exposes
higher level operations like tb_cfg_read/tb_cfg_write.
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Thunderbolt hotplug is supposed to be handled by the firmware. But Apple
decided to implement thunderbolt at the operating system level. The
firmare only initializes thunderbolt devices that are present at boot
time. This driver enables hotplug of thunderbolt of non-chained
thunderbolt devices on Apple systems with a cactus ridge controller.
This first patch adds the Kconfig file as well the parts of the driver
which talk directly to the hardware (that is pci device setup, interrupt
handling and RX/TX ring management).
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mika Westerberg
Linus Torvalds
Rafael J. Wysocki
Dan Carpenter
Bernat, Yehezkel
Lukas Wunner
Christoph Hellwig
Colin Ian King
Amir Levy
Xavier Gnata
Andreas Noever
Knuth Posern
Himangi Saraogi
Arnd Bergmann
Sachin Kamat