The current security model is based around the flags AUTH, ENCRYPT and
SECURE. Starting with support for the Bluetooth 2.1 specification this is
no longer sufficient. The different security levels are now defined as
SDP, LOW, MEDIUM and SECURE.
Previously it was possible to set each security independently, but this
actually doesn't make a lot of sense. For Bluetooth the encryption depends
on a previous successful authentication. Also you can only update your
existing link key if you successfully created at least one before. And of
course the update of link keys without having proper encryption in place
is a security issue.
The new security levels from the Bluetooth 2.1 specification are now
used internally. All old settings are mapped to the new values and this
way it ensures that old applications still work. The only limitation
is that it is no longer possible to set authentication without also
enabling encryption. No application should have done this anyway since
this is actually a security issue. Without encryption the integrity of
the authentication can't be guaranteed.
As default for a new L2CAP or RFCOMM connection, the LOW security level
is used. The only exception here are the service discovery sessions on
PSM 1 where SDP level is used. To have similar security strength as with
a Bluetooth 2.0 and before combination key, the MEDIUM level should be
used. This is according to the Bluetooth specification. The MEDIUM level
will not require any kind of man-in-the-middle (MITM) protection. Only
the HIGH security level will require this.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When the remote device supports only SCO connections, on receipt of
the HCI_EV_CONN_COMPLETE event packet, the connect state is changed to
BT_CONNECTED, but the socket state is not updated. Hence, the connect()
call times out even though the SCO connection has been successfully
established.
Based on a report by Jaikumar Ganesh <jaikumar@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
All SCO and eSCO connection are auto-accepted no matter if there is a
corresponding listening socket for them. This patch changes this and
connection requests for SCO and eSCO without any socket are rejected.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In order to decide if listening L2CAP sockets should be accept()ed
the BD_ADDR of the remote device needs to be known. This patch adds
a socket option which defines a timeout for deferring the actual
connection setup.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In order to decide if listening RFCOMM sockets should be accept()ed
the BD_ADDR of the remote device needs to be known. This patch adds
a socket option which defines a timeout for deferring the actual
connection setup.
The connection setup is done after reading from the socket for the
first time. Until then writing to the socket returns ENOTCONN.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The L2CAP and RFCOMM applications require support for authorization
and the ability of rejecting incoming connection requests. The socket
interface is not really able to support this.
This patch does the ground work for a socket option to defer connection
setup. Setting this option allows calling of accept() and then the
first read() will trigger the final connection setup. Calling close()
would reject the connection.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The socket option levels SOL_L2CAP, SOL_RFOMM and SOL_SCO are currently
in use by various Bluetooth applications. Going forward the common
option level SOL_BLUETOOTH should be used. This patch prepares the clean
split of the old and new option levels while keeping everything backward
compatibility.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In case of connection failures the rfcomm_sock_sendmsg() should return
an error and not a 0 value.
Signed-off-by: Victor Shcherbatyuk <victor.shcherbatyuk@tomtom.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds two new device ids to the asix driver.
One comes directly from the asix driver on their web site, the other was
reported by Armani Liao as needed for the MSI X320 to get the driver to
work properly for it.
Reported-by: Armani Liao <aliao@novell.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently there are two paths for filling rx buffer queues. One is
used during initialization and the other during runtime. This patch
removes ql_alloc_sbq_buffers() and ql_alloc_lbq_buffers() and replaces
them with a call to the runtime functions ql_update_lbq() and
ql_update_sbq().
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RX Buffers are refilled in chunks of 16 at a time before notifying the
hardware with a register write. This can cause several writes to take
place in a given napi poll call. This change causes the write to take place
only once at the end of the call.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of taking/giving the hw semaphore repeatedly when iterating over
several frame to queue route settings, we have the caller hold it until
all are done.
This reduces PCI bus chatter and possible waits.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of taking/giving the semaphore repeatedly when iterating over
several adderesses, we have the caller hold it until all are done. This
reduces PCI bus chatter and possible waits.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Setting MAC addresses and routing frames to various queues will need to
be done in response to firmware events as well as during initialization.
This change encapsulates the facilities into a single call that can
later me made from other places.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The functions time_before is more robust for comparing
jiffies against other values.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The functions time_before is more robust for comparing
jiffies against other values.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The functions time_before is more robust for comparing
jiffies against other values.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove some pointless conditionals before kfree_skb().
The semantic match that finds the problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
expression E;
@@
- if (E)
- kfree_skb(E);
+ kfree_skb(E);
// </smpl>
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the return value of nlmsg_notify() as follows:
If NETLINK_BROADCAST_ERROR is set by any of the listeners and
an error in the delivery happened, return the broadcast error;
else if there are no listeners apart from the socket that
requested a change with the echo flag, return the result of the
unicast notification. Thus, with this patch, the unicast
notification is handled in the same way of a broadcast listener
that has set the NETLINK_BROADCAST_ERROR socket flag.
This patch is useful in case that the caller of nlmsg_notify()
wants to know the result of the delivery of a netlink notification
(including the broadcast delivery) and take any action in case
that the delivery failed. For example, ctnetlink can drop packets
if the event delivery failed to provide reliable logging and
state-synchronization at the cost of dropping packets.
This patch also modifies the rtnetlink code to ignore the return
value of rtnl_notify() in all callers. The function rtnl_notify()
(before this patch) returned the error of the unicast notification
which makes rtnl_set_sk_err() reports errors to all listeners. This
is not of any help since the origin of the change (the socket that
requested the echoing) notices the ENOBUFS error if the notification
fails and should resync itself.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
A receive coalescing timeout of 250 usec appears to strike a good
balance between allowing enough received frames to be aggregated for
LRO to do its job and not allowing the connection to stall due to
delaying ACKs to the remote end for too long.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the netif_carrier_off() call in ->open() to port probe, so that
ethtool doesn't report the link as being up before we have up'd the
interface.
Move initialisation of the rx/tx coalescing timers from ->open() to
port probe, so that we don't reset the coalescing timers every time
the interface is up'd.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split pci probe function into smaller logical blocks.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
it was pointed out on the list that ixgbe was failing when using 64kB pages
and large 16kB MTU.
since with a 64kB PAGE_SIZE MAX_SKB_FRAGS = 3, the way the driver was
configuring page usage was assuming 2kB is half a page, and was only
ever dmaing that much data to a half page.
(16kB - header size) / 2048 = 7 or 8 pages, which would far exceed 3
adjust the driver to account for these large pages, the hardware can
support DMA to up to 16kB for each descriptor.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Shannon Nelson <shannon.nelson@intel.com>
The ring_feature member of ixgbe_adapter is statically allocated based on
the supported features of the device. When a new feature is added, we need
to manually update the static allocation. This patch makes the feature
list an enum, eliminating the need for multiple updates to the code when
adding a new feature.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix regression introduded by commit 079aa88 (netfilter: xt_recent: IPv6 support):
From http://bugzilla.kernel.org/show_bug.cgi?id=12753:
Problem Description:
An uninitialized buffer causes IPv4 addresses added manually (via the +IP
command to the proc interface) to never match any packets. Similarly, the -IP
command fails to remove IPv4 addresses.
Details:
In the function recent_entry_lookup, the xt_recent module does comparisons of
the entire nf_inet_addr union value, both for IPv4 and IPv6 addresses. For
addresses initialized from actual packets the remaining 12 bytes not occupied
by the IPv4 are zeroed so this works correctly. However when setting the
nf_inet_addr addr variable in the recent_mt_proc_write function, only the IPv4
bytes are initialized and the remaining 12 bytes contain garbage.
Hence addresses added in this way never match any packets, unless these
uninitialized 12 bytes happened to be zero by coincidence. Similarly, addresses
cannot consistently be removed using the proc interface due to mismatch of the
garbage bytes (although it will sometimes work to remove an address that was
added manually).
Reading the /proc/net/xt_recent/ entries hides this problem because this only
uses the first 4 bytes when displaying IPv4 addresses.
Steps to reproduce:
$ iptables -I INPUT -m recent --rcheck -j LOG
$ echo +169.254.156.239 > /proc/net/xt_recent/DEFAULT
$ cat /proc/net/xt_recent/DEFAULT
src=169.254.156.239 ttl: 0 last_seen: 119910 oldest_pkt: 1 119910
[At this point no packets from 169.254.156.239 are being logged.]
$ iptables -I INPUT -s 169.254.156.239 -m recent --set
$ cat /proc/net/xt_recent/DEFAULT
src=169.254.156.239 ttl: 0 last_seen: 119910 oldest_pkt: 1 119910
src=169.254.156.239 ttl: 255 last_seen: 126184 oldest_pkt: 4 125434, 125684, 125934, 126184
[At this point, adding the address via an iptables rule, packets are being
logged correctly.]
$ echo -169.254.156.239 > /proc/net/xt_recent/DEFAULT
$ cat /proc/net/xt_recent/DEFAULT
src=169.254.156.239 ttl: 0 last_seen: 119910 oldest_pkt: 1 119910
src=169.254.156.239 ttl: 255 last_seen: 126992 oldest_pkt: 10 125434, 125684, 125934, 126184, 126434, 126684, 126934, 126991, 126991, 126992
$ echo -169.254.156.239 > /proc/net/xt_recent/DEFAULT
$ cat /proc/net/xt_recent/DEFAULT
src=169.254.156.239 ttl: 0 last_seen: 119910 oldest_pkt: 1 119910
src=169.254.156.239 ttl: 255 last_seen: 126992 oldest_pkt: 10 125434, 125684, 125934, 126184, 126434, 126684, 126934, 126991, 126991, 126992
[Removing the address via /proc interface failed evidently.]
Possible solutions:
- initialize the addr variable in recent_mt_proc_write
- compare only 4 bytes for IPv4 addresses in recent_entry_lookup
Signed-off-by: Patrick McHardy <kaber@trash.net>
The IP_ADVANCED_ROUTER Kconfig describes the rp_filter
proc option. Recent changes added a loose mode.
Instead of documenting this change too places, refer to
the document describing it:
Documentation/networking/ip-sysctl.txt
I'm considering moving the rp_filter description away
from the Kconfig file into ip-sysctl.txt.
Signed-off-by: Jesper Dangaard Brouer <hawk@comx.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix up whitespaces while going though ip-sysctl.txt anyway.
Signed-off-by: Jesper Dangaard Brouer <hawk@comx.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
PCI bar 0 is used for memory mapped register access.
If ioremap fails (returns NULL), register access results
in crash.
Use pci_ioremap_bar() instead of ioremap(), the latter
fails on on 32 bit powerpc where pci resource address is
> 32 bits.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PCI function to physical port mapping is valid only for
old firmware. New firmware (4.0.0+) abstracts this.
So driver should never try to access phy using invalid
mapping. The behavior is unpredictable when PCI functions
4-7 are enabled on the same NIC.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
net: amend the fix for SO_BSDCOMPAT gsopt infoleak
netns: build fix for net_alloc_generic
de_get is called before every proc_get_inode, but corresponding de_put is
called only when dropping last reference to an inode. This might cause
something like
remove_proc_entry: /proc/stats busy, count=14496
to be printed to the syslog.
The fix is to call de_put in case of an already initialized inode in
proc_get_inode.
Signed-off-by: Krzysztof Sachanowicz <analyzer1@gmail.com>
Tested-by: Marcin Pilipczuk <marcin.pilipczuk@gmail.com>
Acked-by: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In the KMS case, enter/leavevt won't fix up the interrupt handler for
us, so we need to do it at suspend/resume time. Make sure we don't fail
the resume if the chip is hung either.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
dev_priv->hw_status_page can be NULL, if i915_gem_retire_requests()
is called from i915_gem_busy_ioctl().
Signed-off-by Karsten Wiese <fzu@wemgehoertderstaat.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The fix for CVE-2009-0676 (upstream commit df0bca04) is incomplete. Note
that the same problem of leaking kernel memory will reappear if someone
on some architecture uses struct timeval with some internal padding (for
example tv_sec 64-bit and tv_usec 32-bit) --- then, you are going to
leak the padded bytes to userspace.
Signed-off-by: Eugene Teo <eugeneteo@kernel.sg>
Reported-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net_alloc_generic was defined in #ifdef CONFIG_NET_NS, but used
unconditionally. Move net_alloc_generic out of #ifdef.
Signed-off-by: Clemens Noss <cnoss@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marcel Holtmann
Victor Shcherbatyuk
David S. Miller
Greg Kroah-Hartman
Ron Mercer
Wei Yongjun
Pablo Neira Ayuso
Lennert Buytenhek
Joe Perches
Dhananjay Phadke
Jesse Brandeburg
Shannon Nelson
Josef Drexler
Jesper Dangaard Brouer
Linus Torvalds
Krzysztof Sachanowicz
Jesse Barnes
Karsten Wiese
Eugene Teo
Clemens Noss