.ko is normally not included in Kconfig help, make it consistent.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This driver requests a clock that usually is supplied by the MFD in which
the DS1WM is contained. Currently, it is impossible for a MFD to register
their clocks with the generic clock API due to different implementations
across architectures.
For now, this patch removes the clock handling from DS1WM altogether,
trusting that the MFD enable/disable functions will switch the clock if
needed. The clock rate is obtained from a new parameter in driver_data.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
This patch converts the DS1WM driver into an MFD cell. It also
calculates the bus_shift parameter from the memory resource size.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
This fixes a number of coding style issues I stubled over.
Acked-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The context makes it clear already that these are clocks, so there's
no need for such a suffix. This patch only changes the clocks actually
used in the tree. The remaining clocks are renamed in the subsequent
architecture specific patches.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
W1 master implementations are expected to return 0 or 1 from their
read_bit() function. However, not all platforms do return these values
from gpio_get_value() - namely PXAs won't. Hence the w1 gpio-master needs
to break the result down to 0 or 1 itself.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Ville Syrjala <syrjala@sci.fi>
Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The w1_ds2433 driver does not read from the hardware if the CRC was valid
on the last read. The validcrc flag should be cleared after a write so
that the new value can be read.
Signed-off-by: Ben Gardner <gardner.ben@gmail.com>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Addresses http://bugzilla.kernel.org/show_bug.cgi?id=12646
When the temperature exceeds 32767 milli-degrees the temperature overflows
to -32768 millidegrees. These are bothe well within the -55 - +125 degree
range for the sensor.
Fix overflow in left-shift of a u8.
Signed-off-by: Ian Dall <ian@beware.dropbear.id.au>
Signed-off-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Send completion status of the commands to the userspace. Message and
protocol are described in the documentation.
Signed-off-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Paul Alfille <paul.alfille@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Command which allows to reset the bus.
Signed-off-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Paul Alfille <paul.alfille@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This small patchset extendes existing commands with reset, master IO and
status messages. Reset is used to reset the bus for given master device,
master IO command allows to initiate IO against bus itself not selecting
slave device first, which can be used to probe the device for example.
And status messages carry command completion status back to the userspace
(namely very useful to get -ENODEV from when requested device was not
found).
Great thanks to Paul Alfille of OWFS for testing and commands suggestions.
This patch:
Allow starting of IO not against already found slave devices, but against
the bus itself, which can be used for example to probe devices.
[akpm@linux-foundation.org: reindent switch statements]
Signed-off-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Paul Alfille <paul.alfille@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Initiates search (or alarm search) and returns all found devices to
userspace. Found devices are not added into the system (i.e. they are
not attached to family devices or bus masters), it will be done via (if
was not done yet) usual timed searching.
Signed-off-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Writes and returns sampled data back to userspace.
Signed-off-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch series introduces and extends several userspace commands
used with netlink protocol.
Touch block command allows to write data and return sampled data to
the userspace.
Extended search and alarm seach commands to return list of slave
devices found during given search.
List masters command allows to send all registered master IDs to the
userspace.
Great thanks to Paul Alfille (owfs) who
tested this implementation and wrote w1-to-network daemon
http://sourceforge.net/projects/w1repeater/ and
Frederik Deweerdt and Randy Dunlap for review.
This patch:
Returns list of registered bus master devices.
Signed-off-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Paul Alfille <paul.alfille@gmail.com>
Cc: Frederik Deweerdt <frederik.deweerdt@xprog.eu>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds support for the 1-wire master interface for i.MX27 and
i.MX31.
Signed-off-by: Luotao Fu <l.fu@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
During test of the w1-gpio driver i found that in "w1.c:679
w1_slave_found()" the device id is converted to little-endian with
"cpu_to_le64()", but its not converted back to cpu format in "w1_io.c:293
w1_reset_select_slave()".
Based on a patch created by Andreas Hummel.
[akpm@linux-foundation.org: remove unneeded cast]
Reported-by: Andreas Hummel <andi_hummel@gmx.de>
Signed-off-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Uses clk_...() a lot
Acked-by: rmk+kernel@arm.linux.org.uk
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
OMAP LDP boot crash. This is because w1 subsystem changed the search
interface, so update omap_hdq's search interface to follow the change.
Signed-off-by: Stanley.Miao <stanley.miao@windriver.com>
Signed-off-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The HDQ/1-Wire module of TI OMAP2430/3430 platforms implement the hardware
protocol of the master functions of the Benchmark HDQ and the Dallas
Semiconductor 1-Wire protocols. These protocols use a single wire for
communication between the master (HDQ/1-Wire controller) and the slave
(HDQ/1-Wire external compliant device).
This patch provides the HDQ driver to suppport TI OMAP2430/3430 platforms.
Signed-off-by: Madhusudhan Chikkature<madhu.cr@ti.com>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Acked-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Export the w1_read_8 function for use of drivers. The OMAP HDQ
driver(drivers/w1/masters/omap_hdq.c) uses this function.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Madhusudhan Chikkature<madhu.cr@ti.com>
Acked-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Tejun's commit 7b595756ec made sysfs
attribute->owner unnecessary. But the field was left in the structure to
ease the merge. It's been over a year since that change and it is now
time to start killing attribute->owner along with its users - one arch at
a time!
This patch is attempt #1 to get rid of attribute->owner only for
CONFIG_X86_64 or CONFIG_X86_32 . We will deal with other arches later on
as and when possible - avr32 will be the next since that is something I
can test. Compile (make allyesconfig / make allmodconfig / custom config)
and boot tested.
akpm: the idea is that we put the declaration of sttribute.owner inside
`#ifndef CONFIG_X86'. But that proved to be too ambitious for now because
new usages kept on turning up in subsystem trees.
[akpm: remove the ifdef for now]
Signed-off-by: Parag Warudkar <parag.lkml@gmail.com>
Cc: Greg KH <greg@kroah.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Tejun Heo <htejun@gmail.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[akpm@linux-foundation.org: minor fixlets and cleanups]
Signed-off-by: Bernhard Weirich <bernhard.weirich@riedel.net>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Cc: Ben Gardner <bgardner@wabtec.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Optimize the ds_set_pullup function. For a strong pullup to be sent the
ds2490 has to have both the strong pullup mode enabled, and the specific
write operation has to have the SPU bit enabled. Previously the write
always had the SPU bit enabled and both the duration and model was set
when a strong pullup was requested. Now the strong pullup mode is enabled
at initialization time, the delay is updated only when the value changes,
and the write SPU bit is set only when a strong pullup is required. This
removes two or three bus transactions per strong pullup request.
Signed-off-by: David Fries <david@fries.net>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Drop the extra ds_wait_status() in ds_write_block().
Signed-off-by: David Fries <david@fries.net>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This replaces some magic numbers with marcos and corrects one marco.
Signed-off-by: David Fries <david@fries.net>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Reset the device in init as it can be in a bad state. This is necessary
because a block write will wait for data to be placed in the output buffer
and block any later commands which will keep accumulating and the device
will not be idle. Another case is removing the ds2490 module while a bus
search is in progress, somehow a few commands get through, but the input
transfers fail leaving data in the input buffer. This will cause the next
read to fail see the note in ds_recv_data.
Signed-off-by: David Fries <david@fries.net>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ds_reset no longer calls ds_wait_status, the result wasn't used and it
would only delay the following data operations.
Signed-off-by: David Fries <david@fries.net>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- add result register #defines
- rename ds_dump_status to ds_print_msg
- rename ds_recv_status to ds_dump_status
- ds_dump_status prints the requested status and no longer reads the
status, this is because the second status read can return different
data for example the result register
- the result register will be printed, though limited to detecting a
new device, detecting other values such as a short would require
additional reporting methods
- ST_EPOF was moved to ds_wait_status to clear the error condition
sooner
Signed-off-by: David Fries <david@fries.net>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Simplify and fix ds_touch_bit. If a device is attached in the middle of a
bus search the status register will return more than the default 16 bytes.
The additional bytes indicate that it has detected a new device. The way
ds_wait_status is coded, if it doesn't read 16 status bytes it returns an
error value. ds_touch_bit then will detect that error and return an
error. In that case it doesn't read the input buffer and returns
uninitialized data. It doesn't stop there. The next transaction will not
expect the extra byte in the input buffer and the short read will cause an
error and clear out both the old byte and new data in the input buffer.
Just ignore the value of ds_wait_status. It is still required to wait
until ds2490 is again idle and there is data to read when ds_recv_data is
called. This also removes the while loop. None of the other commands
wait and verify that the issued command is in the status register.
Signed-off-by: David Fries <david@fries.net>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Don't export read and write bit operations, they didn't work, they weren't
used, and they can't be made to work. The one wire low level bit
operations expect to set high or low levels, the ds2490 hardware only
supports complete read or write time slots, better to just comment them
out.
Signed-off-by: David Fries <david@fries.net>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ds_write_bit doesn't read the input buffer, so add COMM_ICP and a comment
that it will no longer generate a read back data byte. If there is an
extra data byte later on then it will cause an error and discard what data
was there. Corrected operator ordering for ds_send_control.
Signed-off-by: David Fries <david@fries.net>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add strong pullup support for ds2490 driver, also drop mdelay(750), which
busy waits, usage in favour of msleep for long delays. Now with msleep
only being called when the strong pullup is active, one wire bus
operations are only taking minimal system overhead.
The new set_pullup will only enable the strong pullup when requested,
which is expected to be the only write operation that will benefit from a
strong pullup.
Signed-off-by: David Fries <david@fries.net>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Corrected print message, it was writing not reading, this also prints the
endpoint used for the write instead of hardcoding it. Failed to write
1-wire data to ep0x%x: err=%d.
Signed-off-by: David Fries <david@fries.net>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Like the previous w1_io.c reset coments and msleep patch, I don't have the
hardware to verify the change, but I think it is safe. It also helps to
see a comment like this in the code. "We'll wait a bit longer just to be
sure." If they are going to calculate delaying 324.9us, but actually delay
500us, why not just give up the CPU and sleep? This is designed for a
battery powered ARM system, avoiding busywaiting has to be good for
battery life.
I sent a request for testers March 7, 2008 to the Linux kernel mailing
list and two developers who have patches for ds1wm.c, but I didn't get
any respons.
Signed-off-by: David Fries <david@fries.net>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
w1_reset_bus, added some comments about the timing and switched to msleep
for the later delay. I don't have the hardware to test the sleep after
reset change. The one wire doesn't have a timing requirement between
commands so it is fine. I do have the USB hardware and it would be in big
trouble with 10ms interrupt transfers to find that the reset completed.
Signed-off-by: David Fries <david@fries.net>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Follow the example of other devices (like the joystick device). Pick the
first available id for each detected device. Currently for USB devices,
suspending and resuming would cause the number to increment.
Signed-off-by: David Fries <david@fries.net>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
sl->master->mutex and dev->mutex refer to the same mutex variable, but be
consistent and use the same set of pointers for the lock and unlock calls.
It is less confusing (and one less pointer dereference this way).
Signed-off-by: David Fries <david@fries.net>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Removed the w1_family structure member variable need_exit. It was only
being set and never used. Even if it were to be used it is a polling type
operation.
Signed-off-by: David Fries <david@fries.net>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fixed data reading bug by replacing binary attribute with device one.
Switching the sysfs read from bin_attribute to device_attribute. The data
is far under PAGE_SIZE so the binary interface isn't required. As the
device_attribute interface will make one call to w1_therm_read per file
open and buffer, the result is, the following problems go away.
buffer overflow:
Execute a short read on w1_slave and w1_therm_read_bin would still
return the full string size worth of data clobbering the user space
buffer when it returned. Switching to device_attribute avoids the
buffer overflow problems. With the snprintf formatted output dealing
with short reads without doing a conversion per read would have
been difficult.
bad behavior:
`cat w1_slave` would cause two temperature conversions to take place.
Previously the code assumed W1_SLAVE_DATA_SIZE would be returned with
each read. It would not return 0 unless the offset was less
than W1_SLAVE_DATA_SIZE. The result was the first read did a
temperature conversion, filled the buffer and returned, the
offset in the second read would be less than
W1_SLAVE_DATA_SIZE and also fill the buffer and return, the
third read would finnally have a big enough offset to return 0
and cause cat to stop. Now w1_therm_read will be called at
most once per open.
Signed-off-by: David Fries <david@fries.net>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix bug reading the id sysfs file. If less than the full 8 bytes were
read, the next read would start at the first byte instead of continuing.
It needed the offset added to memcpy, or the better solution was to
replace it with the device attribute instead of bin attribute.
Signed-off-by: David Fries <david@fries.net>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Added a new module parameter search_count which allows overriding the
default search count. -1 continual, 0 disabled, N that many times.
Signed-off-by: David Fries <david@fries.net>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Simplified the logic in w1_slave_found by using the new
w1_attach_slave_device function to find a slave and mark it as active or
add the device if the crc checks.
Signed-off-by: David Fries <david@fries.net>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pavel Machek
Philipp Zabel
Daniel Mack
Russell King
Sascha Hauer
Herton Ronaldo Krzesinski
Ben Gardner
Ian Dall
Evgeniy Polyakov
Kay Sievers
Evgeniy Polyakov
Al Viro
Stanley.Miao
Madhusudhan Chikkature
Parag Warudkar
Bernhard Weirich
David Fries