The usbhid driver has inconsistently duplicated code in its post-reset,
resume, and reset-resume pathways.
reset-resume doesn't check HID_STARTED before trying to
restart the I/O queues.
resume fails to clear the HID_SUSPENDED flag if HID_STARTED
isn't set.
resume calls usbhid_restart_queues() with usbhid->lock held
and the others call it without holding the lock.
The first item in particular causes a problem following a reset-resume
if the driver hasn't started up its I/O. URB submission fails because
usbhid->urbin is NULL, and this triggers an unending reset-retry loop.
This patch fixes the problem by creating a new subroutine,
hid_restart_io(), to carry out all the common activities. It also
adds some checks that were missing in the original code:
After a reset, there's no need to clear any halted endpoints.
After a resume, if a reset is pending there's no need to
restart any I/O until the reset is finished.
After a resume, if the interrupt-IN endpoint is halted there's
no need to submit the input URB until the halt has been
cleared.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Daniel Fraga <fragabr@gmail.com>
Tested-by: Daniel Fraga <fragabr@gmail.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Instead of open-coding memory allocation and copying form user memory
sequence let's use memdup_user().
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
uhid changes the format expected in write() depending on bitness. It
should check the syscall bitness directly.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: David Herrmann <dh.herrmann@googlemail.com>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The wiimote motion plus gyros use two scales to report fast and slow
rotation - below 440 deg/s uses 8192/440 units / deg/s, and above uses
8192/2000 units / deg/s.
Previously this driver attempted to linearize the two by scaling the fast
rate by 18 and the slow by 9, but this results in a scale of
8192*9/440 = ~167.564 for slow and 8192*18/2000 = 73.728 for fast.
Correct the fast motion scale factor so that both report ~167.564
units / deg/s
Signed-off-by: Cyan Ogilvie <cyan.ogilvie@gmail.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Pull HID updates from Jiri Kosina:
- functionally equivalent cleanups for wacom driver, making the code
more readable, from Benjamin Tissoires
- a bunch of improvements and fixes for thingm driver from Heiner
Kallweit
- bugfixes to out-of-bound access for generic parsing functions (which
have been there since ever) extract() and implement(), from Dmitry
Torokhov
- a lot of added / improved device support in sony, wacom, microsoft,
multitouch and logitech driver, from various people
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (44 commits)
HID: microsoft: Add ID for MS Wireless Comfort Keyboard
hid: thingm: reorder calls in thingm_probe
HID: i2c-hid: fix OOB write in i2c_hid_set_or_send_report()
HID: multitouch: Release all touch slots on reset_resume
HID: usbhid: enable NO_INIT_REPORTS quirk for Semico USB Keykoard2
HID: penmount: report only one button for PenMount 6000 USB touchscreen controller
HID: i2c-hid: Fix suspend/resume when already runtime suspended
HID: i2c-hid: Add hid-over-i2c name to i2c id table
HID: multitouch: force retrieving of Win8 signature blob
HID: Support for CMedia CM6533 HID audio jack controls
HID: thingm: improve locking
HID: thingm: switch to managed version of led_classdev_register
HID: thingm: remove workqueue
HID: corsair: fix mapping of non-keyboard usages
HID: wacom: close the wireless receiver on remove()
HID: wacom: cleanup input devices
HID: wacom: reuse wacom_parse_and_register() in wireless_work
HID: wacom: move down wireless_work()
HID: wacom: break out parsing of device and registering of input
HID: wacom: break out wacom_intuos_get_tool_type
...
Microsoft Wireless Comfort Keyboard has vendor specific My Favorites
1-5 keys. Linux already supports this buttons on other MS keyboards by
MS_ERGONOMY quirk. So apply MS_ERGONOMY quirk to USB PID 0x00e3
(Microsoft Wireless Optical Desktop Receiver 3.0A). After this
My Favorites 1..5 keys will be reported as KEY_F14..KEY_F15 events.
Signed-off-by: Slava Bacherikov <slava@bacher09.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When reviewing another thingm patch Benjamin Tissoires pointed out
the following: "The problem here is that hid_hw_start() is called
before thingm_version() which allows user space to briefly introduce
races between thingm_version() and any hidraw requests.
The mutex will not help here as it is initialized after hid_hw_start()
and only used for protecting the concurrent access of the rgb."
Avoid this possible issue by calling hid_hw_start() later in the
probe function.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Even though hid_hw_* checks that passed in data_len is less than
HID_MAX_BUFFER_SIZE it is not enough, as i2c-hid does not necessarily
allocate buffers of HID_MAX_BUFFER_SIZE but rather checks all device
reports and select largest size. In-kernel users normally just send as much
data as report needs, so there is no problem, but hidraw users can do
whatever they please:
BUG: KASAN: slab-out-of-bounds in memcpy+0x34/0x54 at addr ffffffc07135ea80
Write of size 4101 by task syz-executor/8747
CPU: 2 PID: 8747 Comm: syz-executor Tainted: G BU 3.18.0 #37
Hardware name: Google Tegra210 Smaug Rev 1,3+ (DT)
Call trace:
[<ffffffc00020ebcc>] dump_backtrace+0x0/0x258 arch/arm64/kernel/traps.c:83
[<ffffffc00020ee40>] show_stack+0x1c/0x2c arch/arm64/kernel/traps.c:172
[< inline >] __dump_stack lib/dump_stack.c:15
[<ffffffc001958114>] dump_stack+0x90/0x140 lib/dump_stack.c:50
[< inline >] print_error_description mm/kasan/report.c:97
[< inline >] kasan_report_error mm/kasan/report.c:278
[<ffffffc0004597dc>] kasan_report+0x268/0x530 mm/kasan/report.c:305
[<ffffffc0004592e8>] __asan_storeN+0x20/0x150 mm/kasan/kasan.c:718
[<ffffffc0004594e0>] memcpy+0x30/0x54 mm/kasan/kasan.c:299
[<ffffffc001306354>] __i2c_hid_command+0x2b0/0x7b4 drivers/hid/i2c-hid/i2c-hid.c:178
[< inline >] i2c_hid_set_or_send_report drivers/hid/i2c-hid/i2c-hid.c:321
[<ffffffc0013079a0>] i2c_hid_output_raw_report.isra.2+0x3d4/0x4b8 drivers/hid/i2c-hid/i2c-hid.c:589
[<ffffffc001307ad8>] i2c_hid_output_report+0x54/0x68 drivers/hid/i2c-hid/i2c-hid.c:602
[< inline >] hid_hw_output_report include/linux/hid.h:1039
[<ffffffc0012cc7a0>] hidraw_send_report+0x400/0x414 drivers/hid/hidraw.c:154
[<ffffffc0012cc7f4>] hidraw_write+0x40/0x64 drivers/hid/hidraw.c:177
[<ffffffc0004681dc>] vfs_write+0x1d4/0x3cc fs/read_write.c:534
[< inline >] SYSC_pwrite64 fs/read_write.c:627
[<ffffffc000468984>] SyS_pwrite64+0xec/0x144 fs/read_write.c:614
Object at ffffffc07135ea80, in cache kmalloc-512
Object allocated with size 268 bytes.
Let's check data length against the buffer size before attempting to copy
data over.
Cc: stable@vger.kernel.org
Reported-by: Alexander Potapenko <glider@google.com>
Signed-off-by: Dmitry Torokhov <dtor@chromium.org>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When resetting a device (especially after power loss) it is unlikely
that the firmware will keep the contact tracking data for the previous
touches and will be able to reconcile it with the new contacts, so
let's release all slots on reset resume as start anew.
Signed-off-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Dmitry Torokhov <dtor@chromium.org>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The device which identifies itself as a "USB Keykoard" (no typo)
with VID:PID 1a2c:0027 does not seem to be handling the reports
initialization very well.
This results in a "usb_submit_urb(ctrl) failed: -1" message from the
kernel when connected, and a delay before its initialization. It can
also cause the hang the system.
This patch adds the quirk for this device, which causes the delay
to disappear. It is named as "USB Keykoard2" because the "USB Keykoard"
already exists.
Signed-off-by: Daniel Bristot de Oliveira <bristot@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
PenMount 6000 USB resistive touchscreen controller reports it has three
buttons, while in reality it doesn't have any and doesn't support active
styli, and only generates touch events.
In penmount_input_mapping(), map only the first button (with code 0),
ignore the rest.
Signed-off-by: Andrew Shadura <andrew.shadura@collabora.co.uk>
Tested-by: Christian Gmeiner <c.gmeiner@bachmann.info
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
On ACPI-based systems ACPI power domain code runtime resumes device before
calling suspend method, which ensures that i2c-hid suspend code starts with
device not in low-power state and with interrupts enabled.
On other systems, especially if device is not a part of any power domain,
we may end up calling driver's system-level suspend routine while the
device is runtime-suspended (with controller in presumably low power state
and interrupts disabled). This will result in interrupts being essentially
disabled twice, and we will only re-enable them after both system resume
and runtime resume methods complete. Unfortunately i2c_hid_resume() calls
i2c_hid_hwreset() and that only works properly if interrupts are enabled.
Also if device is runtime-suspended driver's suspend code may fail if it
tries to issue I/O requests.
Let's fix it by runtime-resuming the device if we need to run HID driver's
suspend code and also disabling interrupts only if device is not already
runtime-suspended. Also on resume we mark the device as running at full
power (since that is what resetting will do to it).
Reviewed-by: Benson Leung <bleung@chromium.org>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Dmitry Torokhov <dtor@chromium.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When using the device tree binding OF compatible = "hid-over-i2c" the
i2c id table also needs to have that name in order to auto load this
driver, since i2c core reports module alias as i2c:<string> where
<string> is compatible string of OF binding stripped of manufacturer's
prefix.
Tested-by: Andrew Duggan <aduggan@synaptics.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Dmitry Torokhov <dtor@chromium.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The Synaptics 0x11e5 over I2C found in the Asus T100-CHI requires to
fetch the signature blob to actually start sending events.
With this patch, we should be close enough to the Windows driver which
checks the content of the blob at plugin to validate or not the
touchscreen.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=113481
Fixes: 6d4f5440 ("HID: multitouch: Fetch feature reports on demand for Win8 devices")
Cc: stable@vger.kernel.org
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The C-Media CM6533 is a USB audio chip featuring it's jack detection
capability.The device originates an interrupt transfer via HID interface each
time when a jack event occurs. The purpose of this patch is to handle hid raw
events to keep the operating system informed of user interactions.
Signed-off-by: Ben Chen <ben_chen@bizlinktech.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Reading from the device consists of two operations: sending the read
command and the actual read from the device. If the device is accessed
in between we might read wrong data. Therefore protect the full sequence
of both operations with a mutex.
Also change the semantics of thingm_recv to include both operations.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Simplify the code by switching to the managed version of
led_classdev_register.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Defining workqueues in LED drivers isn't needed any longer as the LED core
was extended with a generic workqueue recently.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This fixes a bug where the Volume Up key was ignored because it uses the same usage code as G18. Special Corsair usage codes are in the keyboard page, other pages should be left to the generic driver.
Signed-off-by: Clément Vuchener <clement.vuchener@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
rmmod/insmod the wacom.ko module does not work for the receiver because
it was not previously closed. Now, we can hack with the wireless receiver
without having to unplug/replug it.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Just some cleaning up when the input devices are unregistered.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Removes duplicated code.
The only difference is that we now need to stop and start the attached hid
device, but this is a small cost.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
If wireless_work() wants to reuse parse_and_register(), we need to have
it declared after this function.
No functional changes.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Simplifies the .probe() and will allow to reuse this path in the future.
Few things are reshuffled in .probe():
- init wacom struct earlier
- then retrieve the report descriptor
- then parse it and allocate/register inputs.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Allow to reuse the code in a later series and simplifies
the reading of wacom_intuos_inout().
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
hid_ignore_special_drivers works fine until hid_scan_report autodetects and
reassign devices (for hid-multitouch, hid-microsoft and hid-rmi).
Simplify the handling of the parameter: if it is there, use hid-generic, no
matter what, and if not, scan the device or rely on the hid_have_special_driver
table.
This was detected while trying to disable hid-multitouch on a Surface Pro cover
which prevented to use the keyboard.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
CC: stable@vger.kernel.org
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The patch that added Logitech Dual Action gamepad support forgot to
update the special driver list for the device. This caused the logitech
driver not to probe unless kernel module load order was favorable.
Update the special driver list to fix it. Thanks to Simon Wood for the
idea.
Cc: Vitaly Katraew <zawullon@gmail.com>
Fixes: 56d0c8b7c8 ("HID: add support for Logitech Dual Action gamepads")
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Double-underscore prefixed types are unnecessary in pure kernel code,
replace them with the non prefixed equivalents.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Antonio Ospite <ao2@ao2.it>
Acked-by: Frank Praznik <frank.praznik@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
WARNING: Block comments use a trailing */ on a separate line
#822: FILE: drivers/hid/hid-sony.c:822:
+ * number but it's not needed for correct operation */
WARNING: Block comments use a trailing */ on a separate line
#828: FILE: drivers/hid/hid-sony.c:828:
+ * buttons multiple keypresses are allowed */
WARNING: Block comments use a trailing */ on a separate line
#854: FILE: drivers/hid/hid-sony.c:854:
+ * 0xff and 11th is for press indication */
WARNING: Missing a blank line after declarations
#1930: FILE: drivers/hid/hid-sony.c:1930:
+ struct sony_sc *sc = container_of(work, struct sony_sc, state_worker);
+ sc->send_output_report(sc);
WARNING: Block comments use a trailing */ on a separate line
#2510: FILE: drivers/hid/hid-sony.c:2510:
+ * Logitech joystick from the device descriptor. */
Signed-off-by: Antonio Ospite <ao2@ao2.it>
Acked-by: Frank Praznik <frank.praznik@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
./scripts/checkpatch.pl \
--types "SPACING,TRAILING_WHITESPACE,POINTER_LOCATION,CODE_INDENT" \
-f drivers/hid/hid-sony.c
ERROR: trailing whitespace
#933: FILE: drivers/hid/hid-sony.c:933:
+^I * $
ERROR: space prohibited after that open square bracket '['
#947: FILE: drivers/hid/hid-sony.c:947:
+ [ 1] = BTN_TRIGGER_HAPPY1,
ERROR: space prohibited after that open square bracket '['
#948: FILE: drivers/hid/hid-sony.c:948:
+ [ 2] = BTN_TRIGGER_HAPPY2,
ERROR: space prohibited after that open square bracket '['
#949: FILE: drivers/hid/hid-sony.c:949:
+ [ 3] = BTN_TRIGGER_HAPPY3,
ERROR: space prohibited after that open square bracket '['
#950: FILE: drivers/hid/hid-sony.c:950:
+ [ 4] = BTN_TRIGGER_HAPPY4,
ERROR: space prohibited after that open square bracket '['
#951: FILE: drivers/hid/hid-sony.c:951:
+ [ 5] = BTN_TRIGGER_HAPPY5,
ERROR: space prohibited after that open square bracket '['
#952: FILE: drivers/hid/hid-sony.c:952:
+ [ 6] = BTN_TRIGGER_HAPPY6,
ERROR: space prohibited after that open square bracket '['
#953: FILE: drivers/hid/hid-sony.c:953:
+ [ 7] = BTN_TRIGGER_HAPPY7,
ERROR: space prohibited after that open square bracket '['
#954: FILE: drivers/hid/hid-sony.c:954:
+ [ 8] = BTN_TRIGGER_HAPPY8,
ERROR: space prohibited after that open square bracket '['
#955: FILE: drivers/hid/hid-sony.c:955:
+ [ 9] = BTN_TRIGGER_HAPPY9,
ERROR: "(foo*)" should be "(foo *)"
#1032: FILE: drivers/hid/hid-sony.c:1032:
+ void(*send_output_report)(struct sony_sc*);
WARNING: missing space after return type
#1032: FILE: drivers/hid/hid-sony.c:1032:
+ void(*send_output_report)(struct sony_sc*);
ERROR: "(foo*)" should be "(foo *)"
#2261: FILE: drivers/hid/hid-sony.c:2261:
+ void(*send_output_report)(struct sony_sc*))
WARNING: missing space after return type
#2261: FILE: drivers/hid/hid-sony.c:2261:
+ void(*send_output_report)(struct sony_sc*))
ERROR: code indent should use tabs where possible
#2449: FILE: drivers/hid/hid-sony.c:2449:
+ */$
total: 13 errors, 2 warnings, 2570 lines checked
Signed-off-by: Antonio Ospite <ao2@ao2.it>
Acked-by: Frank Praznik <frank.praznik@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This adds a warning message stating that the sysfs group was not able to be
created for the passed hid_device structure pointer with dev_warn.
Signed-off-by: Nicholas Krause <xerofoify@gmail.com>
Reviewed-by: Benjamin Tissoires <benajmin.tissoires@redhat.com>
[jkosina@suse.cz: massaged changelog a bit]
[jkosina@suse.cz: reformatted source]
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The midi controller times-out while initializing reports, this
causes boot to take an extra 10 seconds. The device descriptor
advertises that it has an internal HID device but seems to not
actually do anything useful.
Signed-off-by: Stafford Horne <shorne@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
hidpp_ff_init() and hidpp_ff_deinit() are not used outside of
hid-logitech-hidpp.c, so let's make them static.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch implements force feedback support for the Logitech
G920 Driving Force Racing Wheel. It is a generic implementation
of feature 0x8123 of the Logitech HID++ protocol and should be
usable for any future devices that implement this feature.
This patch should be applied after the basic G920 support patch
by Simon Wood:
http://www.spinics.net/lists/linux-input/msg42174.html
The driving supports everything that is supported by the G920
firmware:
FF_CONSTANT
FF_PERIODIC
FF_SINE
FF_SQUARE
FF_SAW_UP
FF_SAW_DOWN
FF_TRIANGLE
FF_SPRING
FF_DAMPER
FF_AUTOCENTER
FF_GAIN
and for version 2 firmware also:
FF_FRICTION
FF_INERTIA
FF_RAMP
Both envelopes and replay values are supported as well, but some
problems may occur when using firmware release 1. There is also a
small residual clockwise damper in the wheel when using the first
firmware release. All problems are fixed in the soon te be released
firmware version 2.
The default spring is disabled by permanently placing a spring
force in the wheel. This spring is also used as the autocenter
spring.
Note: The wheel _DOES_NOT_ auto switch to Logitech/HID mode (it is stuck
in XBox since the xpad changes where not included). Michal has an
alternative approach documented here (and the changes should be submitted
upstream to usb_modeswitch project):
===
Create a file named "046d:c261" in "/etc/usb_modeswitch.d" with the
following content:
DefaultVendor=046d
DefaultProduct=c261
MessageEndpoint=01
ResponseEndpoint=01
TargetClass=0x03
MessageContent="0f00010142"
Then run "usb_modeswitch -c /etc/modeswitch.d/046d:c291" as root and
watch the magic happen:)
===
[jkosina@suse.cz: added information about mode switching from Simon]
[jkosina@suse.cz: fixed a few stylistic issues pointed out by Simon]
[jkosina@suse.cz: fix merge conflict due to to_hid_device() changes]
Signed-off-by: Edwin Velds <e.velds@gmail.com>
Tested-by: Elias Vanderstuyft <elias.vds@gmail.com>
Tested-by: Simon Wood <simon@mungewell.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Commit 0925636042 ("HID: rmi: Disable scanning if the device is not a wake
source") introduced a regression for devices which use hid-rmi to handle
composite USB devices. The suspend or resume callbacks are not checking
that the device is a RMI device before calling rmi_read or rmi_write.
This results in dereferencing uninitialized variables on non RMI devices. This
patch checks that the RMI_DEVICE flag is set before sending RMI commands to the
device.
Reported-by: Rodrigo Gomes <rodrigo.toste.gomes@gmail.com>
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The correct product ID for the old version of the raphnet 4nes4snes
device was 0x0a9d, not 0x0a8d.
Signed-off-by: Raphael Assenat <raph@raphnet.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The asm-generic tree this time contains one series from Nicolas Pitre
that makes the optimized do_div() implementation from the ARM
architecture available to all architectures. This also adds stricter
type checking for callers of do_div, which has uncovered a number
of bugs in existing code, and fixes up the ones we have found.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=4psa
-----END PGP SIGNATURE-----
Merge tag 'asm-generic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull asm-generic updates from Arnd Bergmann:
"The asm-generic tree this time contains one series from Nicolas Pitre
that makes the optimized do_div() implementation from the ARM
architecture available to all architectures.
This also adds stricter type checking for callers of do_div, which has
uncovered a number of bugs in existing code, and fixes up the ones we
have found"
* tag 'asm-generic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
ARM: asm/div64.h: adjust to generic codde
__div64_32(): make it overridable at compile time
__div64_const32(): abstract out the actual 128-bit cross product code
do_div(): generic optimization for constant divisor on 32-bit machines
div64.h: optimize do_div() for power-of-two constant divisors
mtd/sm_ftl.c: fix wrong do_div() usage
drm/mgag200/mgag200_mode.c: fix wrong do_div() usage
hid-sensor-hub.c: fix wrong do_div() usage
ti/fapll: fix wrong do_div() usage
ti/clkt_dpll: fix wrong do_div() usage
tegra/clk-divider: fix wrong do_div() usage
imx/clk-pllv2: fix wrong do_div() usage
imx/clk-pllv1: fix wrong do_div() usage
nouveau/nvkm/subdev/clk/gk20a.c: fix wrong do_div() usage
Plugging a Logitech DJ receiver with KASAN activated raises a bunch of
out-of-bound readings.
The fields are allocated up to MAX_USAGE, meaning that potentially, we do
not have enough fields to fit the incoming values.
Add checks and silence KASAN.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
extract() and implement() access buffer containing reports in 64-bit
chunks, but there is no guarantee that buffers are padded to 64 bit
boundary. In fact, KASAN has caught such OOB access with i2c-hid and
Synaptics touch controller.
Instead of trying to hunt all parties that allocate buffers and make
sure they are padded, let's switch extract() and implement() to byte
access. It is a bit slower, bit we are not dealing with super fast
devices here.
Also let's fix link to the HID spec while we are at it.
Signed-off-by: Dmitry Torokhov <dtor@chromium.org>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The nyko core controller uses the same output report format as the
sixaxis controllers, but it expects the report id at offset 1.
This does not interfere with the official controllers as this byte
is considered a padding byte by the current code.
Signed-off-by: Scott Moreau <oreaus@gmail.com>
Acked-by: Antonio Ospite <ao2@ao2.it>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This adds rumble and LED support for nyko core controllers
using the sino lite chip vendor:1345 product:3008, for PS3.
Setting operational mode and output reports are the same as
sixaxis but the input report has a different format since the
PS3 accepts HID usb devices. For it to work, an exception is
needed to skip overriding the report descriptor and use the
original one.
Signed-off-by: Scott Moreau <oreaus@gmail.com>
Acked-by: Antonio Ospite <ao2@ao2.it>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When setting the operational mode, some third party (Speedlink Strike-FX)
gamepads refuse the output report. Failing here means we refuse to
initialize the gamepad while this should be harmless.
The weird part is that the initial commit that added this: a7de9b8
("HID: sony: Enable Gasia third-party PS3 controllers") mentions this
very same controller as one requiring this output report.
Anyway, it's broken for one user at least, so let's change it.
We will report an error, but at least the controller should work.
And no, these devices present themselves as legacy Sony controllers
(VID:PID of 054C:0268, as in the official ones) so there are no ways
of discriminating them from the official ones.
https://bugzilla.redhat.com/show_bug.cgi?id=1255325
Reported-and-tested-by: Max Fedotov <thesourcehim@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
INTUOSHT2 in range event is not used to indicate in proximity state.
INTUOSHT2 only has one stylus.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
stylus_in_proximity was introduced to support touch arbitration
before in range was supported. With in range event, the logic
changed. stylus_in_proximity should be set for both in prox and
in range events.
To finish a clean touch arbitration logic, we should send touch
up (if it was down) before posting any general pen events.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Move general events related data validation to wacom_intuos_general.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Move wacom_intuos_schedule_prox_event inside wacom_intuos_general
so we don't call it when general event data isn't ready.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Infrastructural changes:
- In struct gpio_chip, rename the .dev node to .parent to better reflect
the fact that this is not the GPIO struct device abstraction. We will
add that soon so this would be totallt confusing.
- It was noted that the driver .get_value() callbacks was
sometimes reporting negative -ERR values to the gpiolib core, expecting
them to be propagated to consumer gpiod_get_value() and gpio_get_value()
calls. This was not happening, so as there was a mess of drivers
returning negative errors and some returning "anything else than zero"
to indicate that a line was active. As some would have bit 31 set to
indicate "line active" it clashed with negative error codes. This is
fixed by the largeish series clamping values in all drivers with
!!value to [0,1] and then augmenting the code to propagate error codes
to consumers. (Includes some ACKed patches in other subsystems.)
- Add a void *data pointer to struct gpio_chip. The container_of() design
pattern is indeed very nice, but we want to reform the struct gpio_chip
to be a non-volative, stateless business, and keep states internal to
the gpiolib to be able to hold on to the state when adding a proper
userspace ABI (character device) further down the road. To achieve this,
drivers need a handle at the internal state that is not dependent on
their struct gpio_chip() so we add gpiochip_add_data() and
gpiochip_get_data() following the pattern of many other subsystems.
All the "use gpiochip data pointer" patches transforms drivers to this
scheme.
- The Generic GPIO chip header has been merged into the general
<linux/gpio/driver.h> header, and the custom header for that removed.
Instead of having a separate mm_gpio_chip struct for these generic
drivers, merge that into struct gpio_chip, simplifying the code and
removing the need for separate and confusing includes.
Misc improvements:
- Stabilize the way GPIOs are looked up from the ACPI legacy
specification.
- Incremental driver features for PXA, PCA953X, Lantiq (patches from the
OpenWRT community), RCAR, Zynq, PL061, 104-idi-48
New drivers:
- Add a GPIO chip to the ALSA SoC AC97 driver.
- Add a new Broadcom NSP SoC driver (this lands in the pinctrl dir, but
the branch is merged here too to account for infrastructural changes).
- The sx150x driver now supports the sx1502.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=63rR
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"Here is the bulk of GPIO changes for v4.5.
Notably there are big refactorings mostly by myself, aimed at getting
the gpio_chip into a shape that makes me believe I can proceed to
preserve state for a proper userspace ABI (character device) that has
already been proposed once, but resulted in the feedback that I need
to go back and restructure stuff. So I've been restructuring stuff.
On the way I ran into brokenness (return code from the get_value()
callback) and had to fix it. Also, refactored generic GPIO to be
simpler.
Some of that is still waiting to trickle down from the subsystems all
over the kernel that provide random gpio_chips, I've touched every
single GPIO driver in the kernel now, oh man I didn't know I was
responsible for so much...
Apart from that we're churning along as usual.
I took some effort to test and retest so it should merge nicely and we
shook out a couple of bugs in -next.
Infrastructural changes:
- In struct gpio_chip, rename the .dev node to .parent to better
reflect the fact that this is not the GPIO struct device
abstraction. We will add that soon so this would be totallt
confusing.
- It was noted that the driver .get_value() callbacks was sometimes
reporting negative -ERR values to the gpiolib core, expecting them
to be propagated to consumer gpiod_get_value() and gpio_get_value()
calls. This was not happening, so as there was a mess of drivers
returning negative errors and some returning "anything else than
zero" to indicate that a line was active. As some would have bit
31 set to indicate "line active" it clashed with negative error
codes. This is fixed by the largeish series clamping values in all
drivers with !!value to [0,1] and then augmenting the code to
propagate error codes to consumers. (Includes some ACKed patches
in other subsystems.)
- Add a void *data pointer to struct gpio_chip. The container_of()
design pattern is indeed very nice, but we want to reform the
struct gpio_chip to be a non-volative, stateless business, and keep
states internal to the gpiolib to be able to hold on to the state
when adding a proper userspace ABI (character device) further down
the road. To achieve this, drivers need a handle at the internal
state that is not dependent on their struct gpio_chip() so we add
gpiochip_add_data() and gpiochip_get_data() following the pattern
of many other subsystems. All the "use gpiochip data pointer"
patches transforms drivers to this scheme.
- The Generic GPIO chip header has been merged into the general
<linux/gpio/driver.h> header, and the custom header for that
removed. Instead of having a separate mm_gpio_chip struct for
these generic drivers, merge that into struct gpio_chip,
simplifying the code and removing the need for separate and
confusing includes.
Misc improvements:
- Stabilize the way GPIOs are looked up from the ACPI legacy
specification.
- Incremental driver features for PXA, PCA953X, Lantiq (patches from
the OpenWRT community), RCAR, Zynq, PL061, 104-idi-48
New drivers:
- Add a GPIO chip to the ALSA SoC AC97 driver.
- Add a new Broadcom NSP SoC driver (this lands in the pinctrl dir,
but the branch is merged here too to account for infrastructural
changes).
- The sx150x driver now supports the sx1502"
* tag 'gpio-v4.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (220 commits)
gpio: generic: make bgpio_pdata always visible
gpiolib: fix chip order in gpio list
gpio: mpc8xxx: Do not use gpiochip_get_data() in mpc8xxx_gpio_save_regs()
gpio: mm-lantiq: Do not use gpiochip_get_data() in ltq_mm_save_regs()
gpio: brcmstb: Allow building driver for BMIPS_GENERIC
gpio: brcmstb: Set endian flags for big-endian MIPS
gpio: moxart: fix build regression
gpio: xilinx: Do not use gpiochip_get_data() in xgpio_save_regs()
leds: pca9532: use gpiochip data pointer
leds: tca6507: use gpiochip data pointer
hid: cp2112: use gpiochip data pointer
bcma: gpio: use gpiochip data pointer
avr32: gpio: use gpiochip data pointer
video: fbdev: via: use gpiochip data pointer
gpio: pch: Optimize pch_gpio_get()
Revert "pinctrl: lantiq: Implement gpio_chip.to_irq"
pinctrl: nsp-gpio: use gpiochip data pointer
pinctrl: vt8500-wmt: use gpiochip data pointer
pinctrl: exynos5440: use gpiochip data pointer
pinctrl: at91-pio4: use gpiochip data pointer
...
Pull HID updates from Jiri Kosina:
- appoint Benjamin Tissoires as co-maintainer / designated reviewer
- sysfs report_descriptor visibility fix for unclaimed devices, from
Andy Lutomirski
- suspend/resume fixes for Sony driver from Frank Praznik
- IRQ deadlock fix from Ioan-Adrian Ratiu
- hid-i2c fixes affecting (at least) Yoga 900 from Mika Westerberg and
Srinivas Pandruvada
- a lot of new device support (especially, but not limited to, Wacom)
and assorted small misc fixes
- almost complete G920 support; the only bit that is missing is
switching the device to HID mode automatically; Simon Wood and Michal
Maly are working on it.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (46 commits)
Revert "INPUT: xpad: switch Logitech G920 Wheel into HID mode"
HID: sensor-hub: Add quirk for Lenovo Yoga 900 with ITE Chips
HID: Add new PID for Microchip Pick16F1454
HID: wacom: Use correct report to query pen ID from INTUOSHT2 devices
HID: i2c-hid: Prevent sending reports from racing with device reset
HID: use kobj_to_dev()
HID: wiimote: use dev_to_wii()
HID: add a new helper to_hid_driver()
HID: use to_hid_device()
HID: move to_hid_device() to hid.h
HID: usbhid: use to_usb_device
HID: corsair: Convert to use module_hid_driver
HID: input: ignore the battery in OKLICK Laser BTmouse
HID: wacom: Fix pad button range for CINTIQ_COMPANION_2
HID: wacom: Fix touchring value reporting
HID: wacom: Report 'strip2' values in ABS_RY
HID: wacom: Limit touchstrip data to 13 bits
HID: wacom: bitwise vs logical ORs
HID: wacom: Apply lowres quirk to BAMBOO_TOUCH devices
HID: enable hid device to suspend/resume asynchronously
...
This needs same quirk as applied to other YOGA sensor hubs. Refer to commit
21589ebda6 ("HID: sensor-hub: Add in quirk for Lenovo Yogas with ITE")
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
There seems to be a new version of the Microchip Pick16F1454 with a
different PID (0xf2f7). This device should also be ignored by the HID
driver. The PID was observed with the second version of the Yepkit Ykush
USB hub.
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Unlike other tablets which are compatible with the wacom_intuos_irq handler,
INTUOSHT2 devices provide pen ID with report ID 8 instead of 5. To ensure
wacom_intuos_schedule_prox_event works as intended for these tablets, we
must be sure it uses the correct report ID in this case.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: linux-input@vger.kernel.org
Acked-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When an i2c-hid device is resumed from system sleep the driver resets
the device to be sure it is in known state. The device is expected to
issue an interrupt when reset is complete.
This reset might take few milliseconds to complete so if the HID driver
on top (hid-rmi) starts to set up the device by sending feature reports
etc. the device might not issue the reset complete interrupt anymore.
Below is what happens to touchpad on Lenovo Yoga 900 during resume from
system sleep:
[ 24.790951] i2c_hid i2c-SYNA2B29:00: i2c_hid_hwreset
[ 24.790973] i2c_hid i2c-SYNA2B29:00: i2c_hid_set_power
[ 24.790982] i2c_hid i2c-SYNA2B29:00: __i2c_hid_command: cmd=22 00 00 08
[ 24.793011] i2c_hid i2c-SYNA2B29:00: resetting...
[ 24.793016] i2c_hid i2c-SYNA2B29:00: __i2c_hid_command: cmd=22 00 00 01
Here i2c-hid sends reset command to the touchpad.
[ 24.794012] i2c_hid i2c-SYNA2B29:00: input: 06 00 01 00 00 00
[ 24.794051] i2c_hid i2c-SYNA2B29:00: i2c_hid_set_or_send_report
[ 24.794059] i2c_hid i2c-SYNA2B29:00: __i2c_hid_command:
cmd=22 00 3f 03 0f 23 00 04 00 0f 01
Now hid-rmi puts the touchpad to correct mode by sending it a feature
report. This makes the touchpad not to issue reset complete interrupt.
[ 24.796092] i2c_hid i2c-SYNA2B29:00: __i2c_hid_command: waiting...
i2c-hid starts to wait for the reset interrupt to trigger which never
happens.
[ 24.798304] i2c_hid i2c-SYNA2B29:00: i2c_hid_set_or_send_report
[ 24.798313] i2c_hid i2c-SYNA2B29:00: __i2c_hid_command:
cmd=25 00 17 00 09 01 42 00 2e 00 19 19 00 10 cc 06 74 04 0f
19 00 00 00 00 00
Yet another output report from hid-rmi driver.
[ 29.795630] i2c_hid i2c-SYNA2B29:00: __i2c_hid_command: finished.
[ 29.795637] i2c_hid i2c-SYNA2B29:00: failed to reset device.
After 5 seconds i2c-hid driver times out.
[ 29.795642] i2c_hid i2c-SYNA2B29:00: i2c_hid_set_power
[ 29.795649] i2c_hid i2c-SYNA2B29:00: __i2c_hid_command: cmd=22 00 01 08
[ 29.797576] dpm_run_callback(): i2c_hid_resume+0x0/0xb0 returns -61
[ 29.797584] PM: Device i2c-SYNA2B29:00 failed to resume: error -61
After this the touchpad does not work anymore (and also resume itself
gets slowed down because of the timeout).
Prevent sending of feature/output reports while the device is being
reset by adding a mutex which is held during that time.
Reported-and-tested-by: Linus Torvalds <torvalds@linux-foundation.org>
Reported-by: Nish Aravamudan <nish.aravamudan@gmail.com>
Suggested-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add a new helper to_hid_driver() and use it in hid-core.c.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
to_hid_device() macro is defined in both hid-lg4ff.c and
hid-logitech-hidpp.c. So I move it to include/linux/hid.h.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This mouse, when asked about the battery, ceases to report movements and
clicks. So just don't ask.
Signed-off-by: Alexander E. Patrakov <patrakov@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Commit c7f0522 incorrectly constructs the 'buttons' variable for the
CINTIQ_COMPANION_2 case. The high nybble of data[2] is shifted four
bits too far, leaving the bits associated with BTN_7 through BTN_A
unset.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Commit c7f0522 reports incorrect touchring values to userspace. This is
due to its incorrect handling of the 'touched' bit present in the 'ring1'
and 'ring2' variables. Instead of using this bit when determining if a
value should be sent, the ABS_WHEEL and ABS_INPUT check (different?!)
portions of the position bits. Furthermore, the full values of 'ring1'
and 'ring2' are reported to userspace, despite the 'touched' flag
needing to be trimmed beforehand. This commit addresses both issues.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Commit c7f0522 accidentally used ABS_RX for reporting both 'strip1' and
'strip2', when the latter should actually be reported through ABS_RY.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Commit c7f0522 uses sixteen bits of data in the construction of 'strip1'
and 'strip2'. This can cause problems in some cases, however, since some
tablets store flags in the MSB of data[2] and data[4] that should not be
included in these values. This restores the 0x1f mask that used prior
to c7f0522.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Smatch complains that these should probably be bitwise ORs instead of
logical. It doesn't matter for "prox" but it makes a difference for
"strip1" and "strip2".
Fixes: c7f0522a1a ('HID: wacom: Slim down wacom_intuos_pad processing')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Here are a number of small USB fixes for 4.4-rc5. All of them have been
in linux-next. The majority are gadget and phy issues, with a few new
quirks and device ids added as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlZs8fkACgkQMUfUDdst+ym/HwCgxdhop3PMk9QxCVaEdxcqv10p
PDkAn0uOW1sdRsHVRhutjcc29+AUJggk
=ybrB
-----END PGP SIGNATURE-----
Merge tag 'usb-4.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB driver fixes from Greg KH:
"Here are a number of small USB fixes for 4.4-rc5. All of them have
been in linux-next. The majority are gadget and phy issues, with a
few new quirks and device ids added as well"
* tag 'usb-4.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (32 commits)
USB: add quirk for devices with broken LPM
xhci: fix usb2 resume timing and races.
usb: musb: fail with error when no DMA controller set
usb: gadget: uvc: fix permissions of configfs attributes
usb: musb: core: Fix pm runtime for deferred probe
usb: phy: msm: fix a possible NULL dereference
USB: host: ohci-at91: fix a crash in ohci_hcd_at91_overcurrent_irq
usb: Quiet down false peer failure messages
usb: xhci: fix config fail of FS hub behind a HS hub with MTT
xhci: Fix memory leak in xhci_pme_acpi_rtd3_enable()
usb: Use the USB_SS_MULT() macro to decode burst multiplier for log message
USB: whci-hcd: add check for dma mapping error
usb: core : hub: Fix BOS 'NULL pointer' kernel panic
USB: quirks: Apply ALWAYS_POLL to all ELAN devices
usb-storage: Fix scsi-sd failure "Invalid field in cdb" for USB adapter JMicron
USB: quirks: Fix another ELAN touchscreen
usb: dwc3: gadget: don't prestart interrupt endpoints
USB: serial: Another Infineon flash loader USB ID
USB: cdc_acm: Ignore Infineon Flash Loader utility
USB: cp210x: Remove CP2110 ID from compatibility list
...
When splitting the touch-only "BAMBOO_TOUCH" type out of the existing
"BAMBOO_PT" type in 3b164a00, the lowres quirk was not updated so that
it would continue to apply to these devices (effectively only the 0xD0).
The absence of this quirk does not significantly impact usability, but
is a correctness issue nonetheless.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Now, PM core supports asynchronous suspend/resume mode for devices
during system suspend/resume, and the power state transition of one
device may be completed in separate kernel thread. PM core ensures
all power state transition timing dependency between devices. This
patch enables hid devices to suspend/resume asynchronously. This
will take advantage of multicore and improve system suspend/resume
speed.
Signed-off-by: Zhonghui Fu <zhonghui.fu@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
"INTUOSREAD" and "INTUOSWRITE" are poorly named. These are report IDs
for pen ID (proximity) packets. It should be noted that the latter is
only used on Intuos/Intuos2 for a second stylus when DualTrack is in use.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Make the logic for reading X, Y, distance, and pressure a bit more
clear. An additional bit was stuffed into the packet format many
models back, and /most/ devices in use will use it. If we happen
to be dealing with a particularly old tablet, just shift it off
the end to pretend we never read it.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Continue re-organizing and trimming cases to make it easier to wrap
the brain around. A number of changes were made after consulting the
protocol spec and so don't necessarily follow from the code itself.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Reasoning through the conditions under which a particular block of code
in 'wacom_intuos_general' will be reached is not at all easy due to the
sheer number of magic masks and comparisons. Remove these and replace
them with a switch statement over the various 'types' of packets that
will be encountered.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Continue to slim down 'wacom_intuos_irq' by moving all decoding and
reporting of pen packet data into the 'wacom_intuos_general' function.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Seperate the function into two halves: first gather data from the packet,
next report all gathered data. The input subsystem should automatically
mute any events that aren't actually declared for the tablet at hand.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Begin slimming down the body of 'wacom_intuos_irq' by moving out its
largest block of code to a dedicated 'wacom_intuos_pad' function.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
as reported by https://bugzilla.kernel.org/show_bug.cgi?id=108481
This bug reports mentions 6d4f5440 ("HID: multitouch: Fetch feature
reports on demand for Win8 devices") as the origin of the problem but this
commit actually masked 2 firmware bugs that are annihilating each other:
The report descriptor declares two features in reports 3 and 5:
0x05, 0x0d, // Usage Page (Digitizers) 318
0x09, 0x0e, // Usage (Device Configuration) 320
0xa1, 0x01, // Collection (Application) 322
0x85, 0x03, // Report ID (3) 324
0x09, 0x22, // Usage (Finger) 326
0xa1, 0x00, // Collection (Physical) 328
0x09, 0x52, // Usage (Inputmode) 330
0x15, 0x00, // Logical Minimum (0) 332
0x25, 0x0a, // Logical Maximum (10) 334
0x75, 0x08, // Report Size (8) 336
0x95, 0x02, // Report Count (2) 338
0xb1, 0x02, // Feature (Data,Var,Abs) 340
0xc0, // End Collection 342
0x09, 0x22, // Usage (Finger) 343
0xa1, 0x00, // Collection (Physical) 345
0x85, 0x05, // Report ID (5) 347
0x09, 0x57, // Usage (Surface Switch) 349
0x09, 0x58, // Usage (Button Switch) 351
0x15, 0x00, // Logical Minimum (0) 353
0x75, 0x01, // Report Size (1) 355
0x95, 0x02, // Report Count (2) 357
0x25, 0x03, // Logical Maximum (3) 359
0xb1, 0x02, // Feature (Data,Var,Abs) 361
0x95, 0x0e, // Report Count (14) 363
0xb1, 0x03, // Feature (Cnst,Var,Abs) 365
0xc0, // End Collection 367
The report ID 3 presents 2 input mode features, while only the first one
is handled by the device. Given that we did not checked if one was
previously assigned, we were dealing with the ignored featured and we
should never have been able to switch this panel into the multitouch mode.
However, the firmware presents an other bugs which allowed 6d4f5440
to counteract the faulty report descriptor. When we request the values
of the feature 5, the firmware answers "03 03 00". The fields are correct
but the report id is wrong. Before 6d4f5440, we retrieved all the features
and injected them in the system. So when we called report 5, we injected
in the system the report 3 with the values "03 00".
Setting the second input mode to 03 in this report changed it to "03 03"
and the touchpad switched to the mt mode. We could have set anything
in the second field because the actual value (the first 03 in this report)
was given by the query of report ID 5.
To sum up: 2 bugs in the firmware were hiding that we were accessing the
wrong feature.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Looks like 29fae1c85 ("HID: logitech: Add support for G29") was a little
bit aggressive and broke other devices.
Fixes: https://bugzilla.kernel.org/show_bug.cgi?id=108121
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
All ELAN hid devices seem to require the ALWAYS_POLL quirk. Let's use
this quirk for all devices from this vendor, rather than maintaining a
list of all its known product IDs.
Tested-by: Adrien Vergé <adrienverge@gmail.com>
Signed-off-by: Adrien Vergé <adrienverge@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The critical section protected by usbhid->lock in hid_ctrl() is too
big and because of this it causes a recursive deadlock. "Too big" means
the case statement and the call to hid_input_report() do not need to be
protected by the spinlock (no URB operations are done inside them).
The deadlock happens because in certain rare cases drivers try to grab
the lock while handling the ctrl irq which grabs the lock before them
as described above. For example newer wacom tablets like 056a:033c try
to reschedule proximity reads from wacom_intuos_schedule_prox_event()
calling hid_hw_request() -> usbhid_request() -> usbhid_submit_report()
which tries to grab the usbhid lock already held by hid_ctrl().
There are two ways to get out of this deadlock:
1. Make the drivers work "around" the ctrl critical region, in the
wacom case for ex. by delaying the scheduling of the proximity read
request itself to a workqueue.
2. Shrink the critical region so the usbhid lock protects only the
instructions which modify usbhid state, calling hid_input_report()
with the spinlock unlocked, allowing the device driver to grab the
lock first, finish and then grab the lock afterwards in hid_ctrl().
This patch implements the 2nd solution.
Signed-off-by: Ioan-Adrian Ratiu <adi@adirat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The code in hid_debug_event() causes horrible code generation. First,
we do a strlen() call for every byte we copy (we're doing a store to
global memory, so gcc has no way of proving that strlen(buf) doesn't
change). Second, since both i, list->tail and HID_DEBUG_BUFSIZE have
signed type, the modulo computation has to take into account the
possibility that list->tail+i is negative, so it's not just a simple
and.
Fix the former by simply not doing strlen() at all (we have to load
buf[i] anyway, so testing it is almost free) and the latter by
changing i to unsigned. This cuts 29% (69 bytes) of the size of the
function.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The usage Confidence is mandary to Windows Precision Touchpad devices. The
appearance of this usage is checked in hidinput_connect but the quirk
MT_QUIRK_VALID_IS_CONFIDENCE is not applied to device accordingly.
Apply this quirk and also remove quirk MT_QUIRK_ALWAYS_VALID to enable palm
rejection for the WIN 8 touchpad devices which have implemented usage
Confidence in its input reports.
Tested on Dell XPS 13 laptop.
Signed-off-by: Allen Hung <allen_hung@dell.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
If an event is discarded the device stays idle. Just reverse the order of
check and marking busy.
Found by code inspection.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
scnprintf() exists to provide these semantics, so we might as well use
it.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Ensure that the G920 is not given the default deadzones.
Signed-off-by: Simon Wood <simon@mungewell.org>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The Logitech G920 uses a couple of vendor specific usage pages,
which results in incorrect number of axis/buttons being detected.
This patch adds these pages to the 'ignore' list.
Reported-by: Elias Vanderstuyft <elias.vds@gmail.com>
Signed-off-by: Simon Wood <simon@mungewell.org>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The G920 can adjust the amount of 'turn' it permits, this patch adds
a sysfs file 'range' to control this.
Signed-off-by: Simon Wood <simon@mungewell.org>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch adds basic support for the Logitech G920 wheel when in HID
mode. This wheel 'speaks' the HID++ protocol, and therefor is driven
with hid-logitech-hidpp.
At this stage the driver only shows that it can communicate with the
wheel by outputting the name discovered over HID++.
The normal HID functions work to give input functionality using
joystick/event interface.
Note: in 'hidpp_probe()' we have to start the hardware to get packets
flowing, the same might apply in future for other devices which don't
use the unifying protocol.
Signed-off-by: Simon Wood <simon@mungewell.org>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Patch add support for the 'very long' HID++ packets, which are
64 bytes in length.
Signed-off-by: Simon Wood <simon@mungewell.org>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Without quirk keyboard repeats '6' until volume control is used since it
indicates the key is pressed without ever releasing.
Signed-off-by: Jimmy Berry <jimmy@boombatower.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Currently the sysfs report_descriptor attribute is only available if the device
is claimed. We have the descriptor before we even create the device node, so
just instantiate report_descriptor statically.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The kobject_put() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
i2c_driver does not need to set an owner because i2c_register_driver()
will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Alan Stern
Dmitry Torokhov
Andy Lutomirski
Cyan Ogilvie
Linus Torvalds
Jiri Kosina
Slava Bacherikov
Heiner Kallweit
Dmitry Torokhov
Benson Leung
Daniel Bristot de Oliveira
Andrew Shadura
Doug Anderson
Benjamin Tissoires
Ben Chen
Clément Vuchener
Grazvydas Ignotas
Pavel Machek
Antonio Ospite
Nicholas Krause
Stafford Horne
Edwin Velds
Andrew Duggan
Raphael Assenat
Scott Moreau
Ping Cheng
Srinivas Pandruvada
Kristian Evensen
Jason Gerecke
Linus Walleij
Mika Westerberg
Geliang Tang
Axel Lin
Alexander E. Patrakov
Dan Carpenter
Fu, Zhonghui
Adrien Vergé
Ioan-Adrian Ratiu
Rasmus Villemoes
Allen Hung
Oliver Neukum
Simon Wood
Jimmy Berry
Markus Elfring
Krzysztof Kozlowski