Add a driver for the ACPI-based EC event interface found on the
OLPC XO-1.5 laptop. This enables notification of battery/AC power events,
and enables various devices to be used as wakeup sources through regular
ACPI mechanisms.
This driver can't be built as a module, because some drivers need to know
at boot-time if SCI-based functionality is available via
olpc_ec_wakeup_available().
Signed-off-by: Daniel Drake <dsd@laptop.org>
Link: http://lkml.kernel.org/r/1309019658-1712-12-git-send-email-dsd@laptop.org
Acked-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Add a driver to configure the XO-1 RTC via CS5536 MSRs, to be used as a
system wakeup source via olpc-xo1-pm.
Device detection is based on finding the relevant device tree node.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Link: http://lkml.kernel.org/r/1309019658-1712-11-git-send-email-dsd@laptop.org
Acked-by: Andres Salomon <dilinger@queued.net>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: devicetree-discuss@lists.ozlabs.org
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
EC events indicate change in AC power connectivity, battery state of
charge, battery error, battery presence, etc. Send notifications to
the power supply subsystem when changes are detected.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Link: http://lkml.kernel.org/r/1309019658-1712-10-git-send-email-dsd@laptop.org
Acked-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Configure the XO-1's lid switch GPIO to trigger an SCI interrupt,
and correctly expose this input device which can be used as a wakeup
source.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Link: http://lkml.kernel.org/r/1309019658-1712-9-git-send-email-dsd@laptop.org
Acked-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
The EC in the OLPC XO-1 delivers GPE events to provide various
notifications. Add the basic code for GPE/EC event processing and
enable the ebook switch, which can be used as a wakeup source.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Link: http://lkml.kernel.org/r/1309019658-1712-8-git-send-email-dsd@laptop.org
Acked-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Update the EC SCI masks with recent additions.
Add functions to query SCI events and set the wakeup mask, to be used by
followup patches.
Add functions to tweak an event mask used to select certain EC events as
a system wakeup source. Also add a function to determine if EC wakeup
functionality is available, as this depends on child drivers (different
for each laptop model) to configure the SCI interrupt.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Link: http://lkml.kernel.org/r/1309019658-1712-7-git-send-email-dsd@laptop.org
Acked-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
The System Control Interrupt is used in the OLPC XO-1 to control various
features of the laptop. Add the driver base and the power button
functionality.
This driver can't be built as a module, because functionality added in
future patches means that some drivers need to know at boot-time whether
SCI-based functionality is available.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Link: http://lkml.kernel.org/r/1309019658-1712-6-git-send-email-dsd@laptop.org
Acked-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Add code needed for basic suspend/resume of the XO-1 laptop.
Based on earlier work by Jordan Crouse, Andres Salomon, and others.
This patch incorporates all earlier feedback from Thomas Gleixner. To
clarify a certain point (now more obvious in the code itself):
On resume, OpenFirmware returns execution to Linux in protected mode
with a kernel-compatible GDT already set up. The changes and
simplifications suggested have all been included.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Link: http://lkml.kernel.org/r/1309019658-1712-5-git-send-email-dsd@laptop.org
Acked-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Based on earlier review comments, we'll no longer try to stick all of
our XO-1 goodies in a single driver. We'll split it into a power management
driver, and an EC/SCI driver.
As a first step, rename olpc-xo1 to olpc-xo1-pm, and make it builtin
instead of modular.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Link: http://lkml.kernel.org/r/1309019658-1712-4-git-send-email-dsd@laptop.org
Acked-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Move these definitions into the relevant header file.
This was requested in the review of the upcoming XO-1 suspend/resume code.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Link: http://lkml.kernel.org/r/1309019658-1712-3-git-send-email-dsd@laptop.org
Acked-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
In response to new device tree code in the kernel, OLPC will start
using it for probing of certain devices. However, some firmware fixes
are needed to put the devicetree into a usable state.
Retain compatibility with old firmware by fixing up the device tree
at boot-time if it does not contain the new nodes/properties that
we need for probing. This is the same approach taken on PPC platforms.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Link: http://lkml.kernel.org/r/1309019658-1712-2-git-send-email-dsd@laptop.org
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Andres Salomon <dilinger@queued.net>
Cc: devicetree-discuss@lists.ozlabs.org
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
* 'at91/fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-2.6-arm-soc:
AT91: Change nand buswidth logic to match hardware default configuration
at91: Use "pclk" as con_id on at91cap9 and at91rm9200
at91: fix udc, ehci and mmc clock device name for cap9/9g45/9rl
atmel_serial: fix internal port num
at91: fix at91_set_serial_console: use platform device id
Commits 71c29bd5c2 ("IB/uverbs: Add devnode method to set path/mode")
and c3af0980ce ("IB: Add devnode methods to cm_class and umad_class")
added devnode methods that set the mode.
However, these methods don't check for a NULL mode, and so we get a
crash when unloading modules because devtmpfs_delete_node() calls
device_get_devnode() with mode == NULL.
Add the missing checks.
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.de>
[ Also fix cm.c. - Roland ]
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The recently modified nand buswitth configuration is not aligned with
board reality: the double footprint on boards is always populated with 8bits
buswidth nand flashes.
So we have to consider that without particular configuration the 8bits
buswidth is selected by default.
Moreover, the previous logic was always using !board_have_nand_8bit(), we
change it to a simpler: board_have_nand_16bit().
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
When releasing framebuffer, free colourmap allocations.
Signed-off-by: Daniel J Blueman <daniel.blueman@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
hwmon: (k10temp) Update documentation for Fam12h
hwmon-vid: Fix typo in VIA CPU name
hwmon: (f71882fg) Add support for the F71869A
hwmon: Use <> rather than () around my e-mail address
hwmon: (emc6w201) Properly handle all errors
Add some CPU series IDs and links to the Fam12h datasheets.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The F71869A is almost the same as the F71869F/E, except that it has
the normal number of temp and pwm zones for a F71882FG derived chip,
rather then the limited number of the F71869F/E.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Max Baldwin <archerseven@gmail.com>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Handle errors on 8-bit register reads and writes too. Also use likely
and unlikely to make the functions faster on success.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
The hard_reset parameter passed to the LLDD in the direct-attached
phy control case allows the LLDD to filter link failure events
while the direct-attached device reset is executing.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The messages emitted from task.c and some from request.c likely
duplicate (in a less undertandable way) what is reported by the
midlayer.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Perform checking per-pci device (even though all systems will only have
1 pci device in this generation), and delete support for silicon that
does not report a proper revision (i.e. A0).
Reported-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Most of these simple dereference macros are longer than their open coded
equivalent. Deleting enum sci_controller_mode is thrown in for good
measure.
Reported-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The distinction between scic_sds_ scic_ and sci_ are no longer relevant
so just unify the prefixes on sci_. The distinction between isci_ and
sci_ is historically significant, and useful for comparing the old
'core' to the current Linux driver. 'sci_' represents the former core as
well as the routines that are closer to the hardware and protocol than
their 'isci_' brethren. sci == sas controller interface.
Also unwind the 'sds1' out of the parameter structs.
Reported-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Remove the distinction between these two implementations and unify on
isci_host (local instances named ihost). Hmmm, we had two
'oem_parameters' instances, one was unused... nice.
Reported-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Remove the distinction between these two implementations and unify on
isci_remote_device (local instances named idev).
Reported-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Remove the distinction between these two implementations and unify on
isci_port (local instances named iport). The duplicate '->owning_port' and
'->isci_port' in both isci_phy and isci_remote_device will be fixed in a later
patch... this is just the straightforward rename/unification.
Reported-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Commit 0815632 "isci: unify remote_device stop_handlers" introduced the
possibility that not all requests get terminated if we reach the
request_count. Now that we properly reference count devices we don't
need this self-defense and can do the straightforward scan of all active
requests.
Reported-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Acked-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
They are one in the same object so remove the distinction. The near
duplicate fields (owning_port, and isci_port) will be cleaned up
after the scic_sds_port isci_port unification.
Reported-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
They are one in the same object so remove the distinction. The near
duplicate fields (owning_controller, and isci_host) will be cleaned up
after the scic_sds_contoller isci_host unification.
Reported-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
* Rename scic_sds_stp_request to isci_stp_request
* Remove the unused fields and union indirection
Reported-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
the dma_pool interface is optimized for object_size << page_size which
is not the case with isci_request objects and the dma_pool routines show
up in the top of the profile.
The old io_request_table which tracked whether tci slots were in-flight
or not is replaced with an IREQ_ACTIVE flag per request.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Combine three bools into one unsigned long 'flags'. Doesn't increase the
request size due to packing. (to do: optimize the structure layout).
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The tci_pool tracks our outstanding command slots which are also the 'index'
portion of our tags. Grabbing the tag early in ->lldd_execute_task let's us
drop the isci_host_can_queue() and ->was_tag_assigned_by_user infrastructure.
->was_tag_assigned_by_user required the task context to be duplicated in
request-local buffer. With the tci established early we can build the
task_context directly into its final location and skip a memcpy.
With the task context buffer at a known address at request construction we
have the opportunity/obligation to also fix sgl handling. This rework feels
like it belongs in another patch but the sgl handling and task_context are too
intertwined.
1/ fix the 'ab' pair embedded in the task context to point to the 'cd' pair in
the task context (previously we were prematurely linking to the staging
buffer).
2/ fix the broken iteration of pio sgls that assumes all sgls are relative to
the request, and does a dangerous looking reverse lookup of physical
address to virtual address.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
When the remote device transitions to a not-ready state because of
an NCQ error condition, all outstanding requests to that device
are terminated and completed to libsas on the normal path. The
device then waits for a READ LOG EXT command to issue on the task
management path.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Updates to the frame_rcvd before need to be atomic with respect to when
they are evaluated by libsas.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
scu_index is a parameter of isci_parse_eom_parameters and is an index
in controller table. There is a check: scu_index > SCI_MAX_CONTROLLERS
which is insufficient and should be: scu_index >= SCI_MAX_CONTROLLERS.
scu_index is used as an index in the table which size is
SCI_MAX_CONTROLLERS.
Signed-off-by: Maciej Patelczyk <maciej.patelczyk@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
1/ fix the timeout for wait_for_completion_timeout
2/ In the tmf timeout case we need to wait for our termination callback
3/ Once the request is successfully started it will be freed according to the
normal lifetime for requests.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Instead of duplicating the smp request buffer reuse the one provided by
libsas. This future proofs the driver to support arbitrarily large smp
requests, and shrinks the request structure size by ~700 bytes.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Daniel Drake
Linus Torvalds
Goldwyn Rodrigues
Nicolas Ferre
Daniel J Blueman
James Bottomley
James Bottomley
Clemens Ladisch
Jean Delvare
Hans de Goede
Jeff Skirvin
Dan Williams
Maciej Patelczyk