Ben Hutchings says:
====================
Pull request: Fixes for new ethtool RSS commands
This addresses several problems I previously identified with the new
ETHTOOL_{G,S}RSSH commands:
1. Missing validation of reserved parameters
2. Vague documentation
3. Use of unnamed magic number
4. No consolidation with existing driver operations
I don't currently have access to suitable network hardware, but have
tested these changes with a dummy driver that can support various
combinations of operations and sizes, together with (a) Debian's ethtool
3.13 (b) ethtool 3.14 with the submitted patch to use ETHTOOL_{G,S}RSSH
and minor adjustment for fixes 1 and 3.
v2: Update RSS operations in vmxnet3 too
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
ETHTOOL_{G,S}RXFHINDIR and ETHTOOL_{G,S}RSSH should work for drivers
regardless of whether they expose the hash key, unless you try to
set a hash key for a driver that doesn't expose it.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When cable is not present the clock speed of some of the devices is
reduced based upon power saving mode setting in NVRAM. Due to this
NVRAM reads take long time to complete as a result CPU soft lockup
message is seen. Fix is to override clock, disable link aware and link
idle modes before NVRAM reads and restore them back after the reads
are complete. During this period also check if the thread needs to be
rescheduled and if there are any signals to handle.
Also decrease the NVRAM command execution timeout value to 1ms.
Signed-off-by: Prashant Sreedharan <prashant@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If any TSO fragment hits hardware bug conditions (e.g. 4G boundary), the
driver will workaround by calling skb_copy() to copy to a linear SKB. Users
have reported page allocation failures as the TSO packet can be up to 64K.
Copying such a large packet is also very inefficient. We fix this by using
existing tg3_tso_bug() to transmit the packet using GSO.
Signed-off-by: Prashant Sreedharan <prashant@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tg3 uses GSO as workaround if the hardware cannot perform TSO on certain
packets. We should not modify the ip header fields if we do GSO on the
packet. It happens to work by accident because GSO recalculates the IP
checksum and IP total length.
Also fix the tg3_start_xmit comment to reflect that this is the only
xmit function for all devices.
Signed-off-by: Prashant Sreedharan <prashant@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch fixes a problem with dropped jumbo frames after usage of
'ethtool -G ... rx'.
Scenario:
1. ip link set eth0 up
2. ethtool -G eth0 rx N # <- This zeroes rx-jumbo
3. ip link set mtu 9000 dev eth0
The ethtool command set rx_jumbo_pending to zero so any received jumbo
packets are dropped and you need to use 'ethtool -G eth0 rx-jumbo N'
to workaround the issue.
The patch changes the logic so rx_jumbo_pending value is changed only if
jumbo frames are enabled (MTU > 1500).
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/marvell/mvneta.c
The mvneta.c conflict is a case of overlapping changes,
a conversion to devm_ioremap_resource() vs. a conversion
to netdev_alloc_pcpu_stats.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Nithin Nayak Sujir <nsujir@broadcom.com>
Cc: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tg3_mdio_reset() does nothing useful and is optional for the MDIO bus
code, so let's just remove it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Including hardware acceleration features in vlan_features breaks
stacked vlans (Q-in-Q) by marking the bottom vlan interface as
capable of acceleration. This causes one of the tags to be lost
and the packets are sent with a sing vlan header.
CC: Nithin Nayak Sujir <nsujir@broadcom.com>
CC: Michael Chan <mchan@broadcom.com>
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the many PTP Hardware Clock drivers with the
newly introduced field that advertises the number of programmable
pins. Some of these devices do have programmable pins, but the
implementation will have to wait for follow on patches.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace dev_kfree_skb with dev_kfree_skb_any in functions that can
be called in hard irq and other contexts.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/wireless/ath/ath9k/recv.c
drivers/net/wireless/mwifiex/pcie.c
net/ipv6/sit.c
The SIT driver conflict consists of a bug fix being done by hand
in 'net' (missing u64_stats_init()) whilst in 'net-next' a helper
was created (netdev_alloc_pcpu_stats()) which takes care of this.
The two wireless conflicts were overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Redefine the RXD_ERR_MASK to include only relevant error bits. This fixes
a customer reported issue of randomly dropping packets on the 5719.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() and pci_enable_msix_range()
interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Cc: Nithin Nayak Sujir <nsujir@broadcom.com>
Cc: Michael Chan <mchan@broadcom.com>
Cc: netdev@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Quoting David Vrabel -
"5780 cards cannot have jumbo frames and TSO enabled together. When
jumbo frames are enabled by setting the MTU, the TSO feature must be
cleared. This is done indirectly by calling netdev_update_features()
which will call tg3_fix_features() to actually clear the flags.
netdev_update_features() will also trigger a new netlink message for the
feature change event which will result in a call to tg3_get_stats64()
which deadlocks on the tg3 lock."
tg3_set_mtu() does not need to be under the tg3 lock since converting
the flags to use set_bit(). Move it out to after tg3_netif_stop().
Reported-by: David Vrabel <david.vrabel@citrix.com>
Tested-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the original code, if tg3_readphy() fails then it does an unnecessary
check to verify "err" is still zero and then returns -EBUSY.
My static checker complains about the unnecessary "if (!err)" check and
anyway it is better to propagate the -EBUSY error code from
tg3_readphy() instead of hard coding it here. And really the original
code is confusing to look at.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
This covers everything under drivers/net except for wireless, which
has been submitted separately.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_pf.c
net/ipv6/ip6_tunnel.c
net/ipv6/ip6_vti.c
ipv6 tunnel statistic bug fixes conflicting with consolidation into
generic sw per-cpu net stats.
qlogic conflict between queue counting bug fix and the addition
of multiple MAC address support.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On ASF enabled devices where the mgmt firmware runs on the application
processing engine, there is a race between the tg3 driver processing a
link change event and the ASF firmware clearing the link changed bit in
the EMAC status register. This leads to link notifications to the driver
sometimes getting lost.
Poll the CPMU link state as a backup for the normal interrupt path
update if ASF is enabled.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On the 5717, 5718 and 5719 devices, the bootcode runs slower when any
port doesn't have a link due to clock speed slowing down as part of the
link-aware feature. This leads to the driver timing out waiting for the
bootcode signature.
This patch overrides the clock policy to the highest frequency just before
reset and restores it after the bootcode is up.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Up to 3 additional unicast addresses can be added to the perfect match
filter table.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
so that individual MAC address filter entries can be set.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current driver assumes that an skb fragment can only be upto jumbo
size. Presumably this was a fast-path optimization. This assumption is
no longer true as fragments can be upto 32k.
v2: Remove unnecessary parantheses per Eric Dumazet.
Cc: stable@vger.kernel.org
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/intel/i40e/i40e_main.c
drivers/net/macvtap.c
Both minor merge hassles, simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
The new tg3 driver leaves REG_BASE_ADDR (PCI config offset 120)
uninitialized. From power on reset this register may have garbage in it. The
Register Base Address register defines the device local address of a
register. The data pointed to by this location is read or written using
the Register Data register (PCI config offset 128). When REG_BASE_ADDR has
garbage any read or write of Register Data Register (PCI 128) will cause the
PCI bus to lock up. The TCO watchdog will fire and bring down the system.
Signed-off-by: Nat Gurumoorthy <natg@google.com>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 4d95847381 - "tg3: Workaround
rx_discards stat bug", added a workaround for miscounted statistics for
multicast packets. This fix needs to be applied to the 5762.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some link partners have issues if the non-standard 1G half duplex is
advertised. This patch adds support for an nvram setting to disable the
advertisement.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rxbds_empty is an informational statistic signifying that a ring full
condition was observed. It does not mean an overflow has occurred.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings says:
====================
SIOCGHWTSTAMP ioctl
1. Add the SIOCGHWTSTAMP ioctl and update the timestamping
documentation.
2. Implement SIOCGHWTSTAMP in most drivers that support SIOCSHWTSTAMP.
3. Add a test program to exercise SIOC{G,S}HWTSTAMP.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Modify tg3_chip_reset() and tg3_close() to check if the PCI network
adapter device is accessible at all in order to skip poking it or
trying to handle a carrier loss in vain when that's not the case.
Introduce a special PCI helper function pci_device_is_present()
for this purpose.
Of course, this uncovers the lack of the appropriate RTNL locking
in tg3_suspend() and tg3_resume(), so add that locking in there
too.
These changes prevent tg3 from burning a CPU at 100% load level for
solid several seconds after the Thunderbolt link is disconnected from
a Matrox DS1 docking station.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use new hwmon API to simplify code, provide missing mandatory 'name'
sysfs attribute, and attach hwmon attributes to hwmon device instead
of pci device.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While we're doing this, fix the error code for SIOCSHWTSTAMP ioctl on
non-timestamping hardware.
Compile-tested only.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
tg3_hwtstamp_ioctl() should validate all fields of hwtstamp_config
before making any changes. Currently it sets the TX configuration
before validating the rx_filter field.
Compile-tested only.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If build_skb fails the memory associated with the ring buffer is freed but
the ri->data member is not zeroed in this case. This causes a double-free
of this memory in tg3_free_rings->... path. The patch moves this block after
setting ri->data to NULL.
It would be nice to fix this bug also in stable >= v3.4 trees.
Cc: Nithin Nayak Sujir <nsujir@broadcom.com>
Cc: Michael Chan <mchan@broadcom.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the memset/memcpy uses of 6 to ETH_ALEN
where appropriate.
Also convert some struct definitions and u8 array
declarations of [6] to ETH_ALEN.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a switch is connected as a PHY to the MAC driven by tg3, use
phylib and provide the phy address to tg3 from the sprom.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When phylib was in use tg3 only searched at address 01 on the mdio
bus and did not work with any other address. On the BCM4705 SoCs the
switch is connected as a PHY behind the MAC driven by tg3 and it is at
PHY address 30 in most cases. This is a preparation patch to allow
support for such switches.
phy_addr is set to TG3_PHY_MII_ADDR for all devices, which are using
phylib, so this should not change any behavior.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The spinlock is not needed after conversion of tg3_flags from array to
set_bit().
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Distinguish between tx, rx and txrx interrupts.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On the 5717, 5719, 5720 and 5762 devices, in shared link/activity mode,
the blink rate must be overridden with all bits set.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for 57764, 57765, 57787, 57782 and 57786
devices.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For consistency with other register access functions, add shadow
register access function of the type (register/val).
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller
Ben Hutchings
Prashant Sreedharan
Michael Chan
Ivan Vecera
françois romieu
Florian Fainelli
Vlad Yasevich
Richard Cochran
Eric W. Biederman
Alexander Gordeev
Nithin Sujir
Dan Carpenter
Paul Gortmaker
Nat Gurumoorthy
Rafael J. Wysocki
Guenter Roeck
Ben Hutchings
Jingoo Han
Joe Perches
Hauke Mehrtens