Pull networking updates from David Miller:
1) Seccomp BPF filters can now be JIT'd, from Alexei Starovoitov.
2) Multiqueue support in xen-netback and xen-netfront, from Andrew J
Benniston.
3) Allow tweaking of aggregation settings in cdc_ncm driver, from Bjørn
Mork.
4) BPF now has a "random" opcode, from Chema Gonzalez.
5) Add more BPF documentation and improve test framework, from Daniel
Borkmann.
6) Support TCP fastopen over ipv6, from Daniel Lee.
7) Add software TSO helper functions and use them to support software
TSO in mvneta and mv643xx_eth drivers. From Ezequiel Garcia.
8) Support software TSO in fec driver too, from Nimrod Andy.
9) Add Broadcom SYSTEMPORT driver, from Florian Fainelli.
10) Handle broadcasts more gracefully over macvlan when there are large
numbers of interfaces configured, from Herbert Xu.
11) Allow more control over fwmark used for non-socket based responses,
from Lorenzo Colitti.
12) Do TCP congestion window limiting based upon measurements, from Neal
Cardwell.
13) Support busy polling in SCTP, from Neal Horman.
14) Allow RSS key to be configured via ethtool, from Venkata Duvvuru.
15) Bridge promisc mode handling improvements from Vlad Yasevich.
16) Don't use inetpeer entries to implement ID generation any more, it
performs poorly, from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1522 commits)
rtnetlink: fix userspace API breakage for iproute2 < v3.9.0
tcp: fixing TLP's FIN recovery
net: fec: Add software TSO support
net: fec: Add Scatter/gather support
net: fec: Increase buffer descriptor entry number
net: fec: Factorize feature setting
net: fec: Enable IP header hardware checksum
net: fec: Factorize the .xmit transmit function
bridge: fix compile error when compiling without IPv6 support
bridge: fix smatch warning / potential null pointer dereference
via-rhine: fix full-duplex with autoneg disable
bnx2x: Enlarge the dorq threshold for VFs
bnx2x: Check for UNDI in uncommon branch
bnx2x: Fix 1G-baseT link
bnx2x: Fix link for KR with swapped polarity lane
sctp: Fix sk_ack_backlog wrap-around problem
net/core: Add VF link state control policy
net/fsl: xgmac_mdio is dependent on OF_MDIO
net/fsl: Make xgmac_mdio read error message useful
net_sched: drr: warn when qdisc is not work conserving
...
Add software TSO support for FEC.
This feature allows to improve outbound throughput performance.
Tested on imx6dl sabresd board, running iperf tcp tests shows:
- 16.2% improvement comparing with FEC SG patch
- 82% improvement comparing with NO SG & TSO patch
$ ethtool -K eth0 tso on
$ iperf -c 10.192.242.167 -t 3 &
[ 3] local 10.192.242.108 port 35388 connected with 10.192.242.167 port 5001
[ ID] Interval Transfer Bandwidth
[ 3] 0.0- 3.0 sec 181 MBytes 506 Mbits/sec
During the testing, CPU loading is 30%.
Since imx6dl FEC Bandwidth is limited to SOC system bus bandwidth, the
performance with SW TSO is a milestone.
CC: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
CC: Eric Dumazet <eric.dumazet@gmail.com>
CC: David Laight <David.Laight@ACULAB.COM>
CC: Li Frank <B20596@freescale.com>
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add Scatter/gather support for FEC.
This feature allows to improve outbound throughput performance.
Tested on imx6dl sabresd board:
Running iperf tests shows a 55.4% improvement.
$ ethtool -K eth0 sg off
$ iperf -c 10.192.242.167 -t 3 &
[ 3] local 10.192.242.108 port 52618 connected with 10.192.242.167 port 5001
[ ID] Interval Transfer Bandwidth
[ 3] 0.0- 3.0 sec 99.5 MBytes 278 Mbits/sec
$ ethtool -K eth0 sg on
$ iperf -c 10.192.242.167 -t 3 &
[ 3] local 10.192.242.108 port 52617 connected with 10.192.242.167 port 5001
[ ID] Interval Transfer Bandwidth
[ 3] 0.0- 3.0 sec 154 MBytes 432 Mbits/sec
CC: Li Frank <B20596@freescale.com>
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to support SG, software TSO, let's increase BD entry number.
CC: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
CC: Eric Dumazet <eric.dumazet@gmail.com>
CC: David Laight <David.Laight@ACULAB.COM>
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to enhance the code readable, let's factorize the
feature list.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IP header checksum is calcalated by network layer in default.
To support software TSO, it is better to use HW calculate the
IP header checksum.
FEC hw checksum feature request the checksum field in frame
is zero, otherwise the calculative CRC is not correct.
For segmentated TCP packet, HW calculate the IP header checksum again,
it doesn't bring any impact. For SW TSO, HW calculated checksum bring
better performance.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the code more readable and easy to support other features like
SG, TSO, moving the common transmit function to one api.
And the patch also factorize the getting BD index to it own function.
CC: David Laight <David.Laight@ACULAB.COM>
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Print the device address, the register number and the PHY ID for
which the MDIO read operation failed
Signed-off-by: Shruti Kanetkar <Shruti@Freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/xen-netback/netback.c
net/core/filter.c
A filter bug fix overlapped some cleanups and a conversion
over to some new insn generation macros.
A xen-netback bug fix overlapped the addition of multi-queue
support.
Signed-off-by: David S. Miller <davem@davemloft.net>
Quoting David Miller:
"At the moment you call register_netdev() the device is visible, notifications
are sent to userspace, and userland tools can try to bring the interface up
and see the incorrect link state, before you do the netif_carrier_off().
Said another way, between the register_netdev() and netif_carrier_off() call,
userspace can see the device in an inconsistent state."
So call netif_carrier_off() prior to register_netdev().
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Building with CONFIG_DEBUG_SECTION_MISMATCH enabled, the following
WARNING is occured:
LD drivers/net/built-in.o
WARNING: drivers/net/built-in.o(.text+0xcd4c): Section mismatch in
reference from the function gfar_probe() to the function
.init.text:gfar_init_addr_hash_table()
The function gfar_probe() references
the function __init gfar_init_addr_hash_table().
This is often because gfar_probe lacks a __init
annotation or the annotation of gfar_init_addr_hash_table is wrong.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 5bbde4d2ec ("net: fec: use pinctrl PM helpers") caused the following
build error on m68k:
drivers/net/ethernet/freescale/fec_main.c: In function 'fec_enet_open':
drivers/net/ethernet/freescale/fec_main.c:1819:2: error: implicit declaration of function 'pinctrl_pm_select_default_state' [-Werror=implicit-function-declaration]
drivers/net/ethernet/freescale/fec_main.c: In function 'fec_enet_close':
drivers/net/ethernet/freescale/fec_main.c:1863:2: error: implicit declaration of function 'pinctrl_pm_select_sleep_state' [-Werror=implicit-function-declaration]
In order to fix the build error, include the linux/pinctrl/consumer.h header
file.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
when system suspend, need to set pins to low power state to
save IO power consumption, there are three states of pinctrl:
"default", "idle" and "sleep". Currently enet supports default
and sleep state.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_phy_connect_fixed_link() is becoming obsolete, and also required
platform code to register the fixed PHYs at the specified addresses for
those to be usable. Get rid of it and use the new of_phy_is_fixed_link()
plus of_phy_register_fixed_link() helpers to transition over the new
scheme.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_phy_connect_fixed_link() is becoming obsolete, and also required
platform code to register the fixed PHYs at the specified addresses for
those to be usable. Get rid of it and use the new of_phy_is_fixed_link()
plus of_phy_register_fixed_link() helpers to transition over the new
scheme.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_phy_connect_fixed_link() is becoming obsolete, and also required
platform code to register the fixed PHYs at the specified addresses for
those to be usable. Get rid of it and use the new of_phy_is_fixed_link()
plus of_phy_register_fixed_link() helpers to transition over the new
scheme.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since imx serials FEC/ENET MDIO clock source is internal ipg clock,
and "ahb" clock is defined as FEC/ENET bus clock, so the patch just
correct the fec driver MDIO clock source.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Acked-by: Frank Li <frank.li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add below clock management to save fec power:
- After probe, disable all clocks incluing ipg, ahb, enet_out, ptp clock.
- Open ethx interface enable necessary clocks.
Close ethx interface disable all clocks.
The patch also encapsulates the all enet clocks enable/disable to
.fec_enet_clk_enable(), which can reduce the repetitional code in
driver.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Acked-by: Frank Li <Frank.li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net: get rid of SET_ETHTOOL_OPS
Dave Miller mentioned he'd like to see SET_ETHTOOL_OPS gone.
This does that.
Mostly done via coccinelle script:
@@
struct ethtool_ops *ops;
struct net_device *dev;
@@
- SET_ETHTOOL_OPS(dev, ops);
+ dev->ethtool_ops = ops;
Compile tested only, but I'd seriously wonder if this broke anything.
Suggested-by: Dave Miller <davem@davemloft.net>
Signed-off-by: Wilfried Klaebe <w-lkml@lebenslange-mailadresse.de>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For phy devices that don't issue interrupts upon link
state changes, phylib polls the link state resulting in
repeated calls to adjust_link(), even if the link state
didn't change. As a result, some mac registers are
repeatedly read and written with the same values, which
is not ok.
To fix this, adjust_link() has been refactored to check
first whether the link state has changed and to take action
only if needed, updating mac registers and local state
variables. The 'new_state' local flag, set if one of the
link params changed (link, speed or duplex), has been
rendered useless and removed by this refactoring.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes a seg fault on 'ethtool -A' entry if the
interface is down. Obviously we need to have the
phy device initialized / "connected" (see of_phy_connect())
to be able to advertise pause frame capabilities.
Fixes: 23402bddf9
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Though we made sure to acquire a valid MAC for
the netdevice we never actually programmed it
into the hardware.
So if the bootloader did not set the MAC,
network operation would only work if userspace
explicitly asked to transfer the MAC to hardware.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
fs_enet_fec_mii_reset() does nothing useful and is optional for the MDIO
bus code, so let's just remove it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fec_enet_mdio_reset() does nothing useful and is optional for the MDIO
bus code, so let's just remove it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace dev_kfree_skb with dev_consume_skb_any in ucc_geth_tx that can
be called in hard irq and other contexts, when processing the
tx completion event.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Replace kfree_skb with dev_kfree_skb_any in fec_enet_start_xmit that
can be called in hard irq and other contexts, when the packet is
dropped.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
The P1010 device tree restricts the number of
supported interrupt groups to 1, although the eth
controller can support 2 interrupt groups and the
driver assumes the Multi-Group mode ("fsl,etsec2" model).
So, in this case the assumption that the Multi-Group
mode (MQ_MG_MODE) devices always support 2 interrupt
groups is false. To fix this, a check for the actual
number of interrupt groups enabled in the board's
device tree has been added in gfar_probe for the
"fsl,etsec2" devices.
Without this fix, P1010 based boards claim support for
2 Tx queues to the net stack but only one is actually
allocated, leading to NULL access in xmit. This issue
was introduced by enabling Single-Queue polling for
the P1010 devices.
(71ff9e3 gianfar: Use Single-Queue polling for
"fsl,etsec2")
Fixes: 71ff9e3df7
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the many PTP Hardware Clock drivers with the
newly introduced field that advertises the number of programmable
pins. Some of these devices do have programmable pins, but the
implementation will have to wait for follow on patches.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Processing any incoming packets with a with a napi budget of 0
is incorrect driver behavior.
This matters as netpoll will shortly call drivers with a budget of 0
to avoid receive packet processing happening in hard irq context.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/usb/r8152.c
drivers/net/xen-netback/netback.c
Both the r8152 and netback conflicts were simple overlapping
changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
If the Freescale fec is in promiscuous mode and network cable is
reconnected then the promiscuous mode get lost. The problem is caused
by a too soon call of set_multicast_list to re-enable promisc mode.
The FEC_R_CNTRL register changes are overwritten by fec_restart.
This patch fixes this by moving the call behind the init of FEC_R_CNTRL
register in fec_restart.
Successful tested on a i.MX28 board.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netpoll can call functions in hard irq context that are ordinarily
called in lesser contexts. For those functions use dev_kfree_skb_any
and dev_consume_skb_any so skbs are freed safely from hard irq
context.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
priv is not instantiated at gfar_of_init() time, when
parsing the DT for info on supported HW queues. Before
the netdev can be allocated, the number of supported
queues must be known. Because the number of supported
queues depends on device type, move the compatibility
checks before netdev allocation. Local vars are used
to hold the operation mode info before netdev allocation.
This fixes the null accesses for priv->.., in gfar_of_init.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the "fsl,etsec2" compatible models the driver currently
supports 8 Tx and Rx DMA rings (aka HW queues). However, there
are only 2 pairs of Rx/Tx interrupt lines, as these controllers
are integrated in low power SoCs with 2 CPUs at most. As a result,
there are at most 2 NAPI instances that have to service multiple
Tx and Rx queues for these devices. This complicates the NAPI
polling routine having to iterate over the mutiple Rx/Tx queues
hooked to the same interrupt lines. And there's also an overhead
at HW level, as the controller needs to service all the 8 Tx rings
in a round robin manner. The combined overhead shows up for multi
parallel Tx flows transmitted by the kernel stack, when the driver
usually starts returning NETDEV_TX_BUSY leading to NETDEV WATCHDOG
Tx timeout triggering if the Tx path is congested for too long.
As an alternative, this patch makes the driver support only one
Tx/Rx DMA ring per NAPI instance (per interrupt group or pair
of Tx/Rx interrupt lines) by default. The simplified single queue
polling routine (gfar_poll_sq) will be the default napi poll routine
for the etsec2 devices too. Some adjustments needed to be made to
link the Tx/Rx HW queues with each NAPI instance (2 in this case).
The gfar_poll_sq() is already successfully used by older SQ_SG_MODE
(single interrupt group) controllers.
This patch fixes Tx timeout triggering under heavy Tx traffic load
(i.e. iperf -c -P 8) for the "fsl,etsec2" (currently the only
MQ_MG_MODE devices). There's also a significant memory footprint
reduction by supporting 2 Rx/Tx DMA rings (at most), instead of 8,
for these devices.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are some concurrency issues on devices w/ 2 CPUs related
to the handling of Rx and Tx interrupts. eTSEC has separate
interrupt lines for Rx and Tx but a single imask register
to mask these interrupts and a single NAPI instance to handle
both Rx and Tx work. As a result, the Rx and Tx ISRs are
identical, both are invoking gfar_schedule_cleanup(), however
both handlers can be entered at the same time when the Rx and
Tx interrupts are taken by different CPUs. In this case
spurrious interrupts (SPU) show up (in /proc/interrupts)
indicating a concurrency issue. Also, Tx overruns followed
by Tx timeout have been observed under heavy Tx traffic load.
To address these issues, the schedule cleanup ISR part has
been changed to handle the Rx and Tx interrupts independently.
The patch adds a separate NAPI poll routine for Tx cleanup to
be triggerred independently by the Tx confirmation interrupts
only. Existing poll functions are modified to handle only
the Rx path processing. The Tx poll routine does not need a
budget, since Tx processing doesn't consume NAPI budget, and
hence it is registered with minimum NAPI weight.
NAPI scheduling does not require locking since there are
different NAPI instances between the Rx and Tx confirmation
paths now.
So, the patch fixes the occurence of spurrious Rx/Tx interrupts.
Tx overruns also occur less frequently now.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/wireless/ath/ath9k/recv.c
drivers/net/wireless/mwifiex/pcie.c
net/ipv6/sit.c
The SIT driver conflict consists of a bug fix being done by hand
in 'net' (missing u64_stats_init()) whilst in 'net-next' a helper
was created (netdev_alloc_pcpu_stats()) which takes care of this.
The two wireless conflicts were overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Programming the interrupt coalescing (IC) registers while
the controller/DMA is on may incur the loss of one Tx
confirmation interrupt, under certain conditions. This is
a subtle hw race because it does not occur during a burst
of Tx packets. It has been observed on p2020 devices that,
if just one packet is being xmit'ed, the Tx confirmation
doesn't trigger and BQL evetually blocks the Tx queues,
followed by Tx timeout and an un-responsive device.
This issue was not apparent prior to introducing BQL
support, as a late Tx confirmation was not an issue back then
and the next burst of Tx frames would have triggered the
Tx confirmation/ Tx ring cleanup anyway.
Bottom line, the hw specifications state that the IC registers
should not be programmed while the Rx/Tx blocks (the DMA) are
enabled. Further more, these registers are currently re-written
with the same values on the processing path, over and over again.
To fix this, rewriting the IC registers has been removed from
the processing path (napi poll). A complete MAC reset procedure
has been implemented for the ethtool -c option instead, to
reliably update these registers while the controller is stopped.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device reset procedure, stop_gfar()/startup_gfar(), has
concurrency issues.
"Kernel access of bad area" oopses show up during Tx timeout
device reset or other reset cases (like changing MTU) that
happen while the interface still has traffic. The oopses
happen in start_xmit and clean_tx_ring when accessing tx_queue->
tx_skbuff which is NULL. The race comes from de-allocating the
tx_skbuff while transmission and napi processing are still
active. Though the Tx queues get temoprarily stopped when Tx
timeout occurs, they get re-enabled as a result of Tx congestion
handling inside the napi context (see clean_tx_ring()). Not
disabling the napi during reset is also a bug, because
clean_tx_ring() will try to access tx_skbuff while it is being
de-alloc'ed and re-alloc'ed.
To fix this, stop_gfar() needs to disable napi processing
after stopping the Tx queues. However, in order to prevent
clean_tx_ring() to re-enable the Tx queue before the napi
gets disabled, the device state DOWN has been introduced.
It prevents the Tx congestion management from re-enabling the
de-congested Tx queue while the device is brought down.
An additional locking state, RESETTING, has been introduced
to prevent simultaneous resets or to prevent configuring the
device while it is resetting.
The bogus 'rxlock's (for each Rx queue) have been removed since
their purpose is not justified, as they don't prevent nor are
suited to prevent device reset/reconfig races (such as this one).
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Resetting the device (stop_gfar()/startup_gfar()) should
be fast and to the point, in order to timely recover
from an error condition (like Tx timeout) or during
device reconfig. The irq free/ request routines are just
redundant here, and they should be part of the device
close/ open routines instead.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RCTRL and TCTRL registers should not be changed
on-the-fly, while the controller is running, otherwise
unexpected behaviour occurs. But that's exactly what
gfar_vlan_mode() does, updating the VLAN acceleration
bits inside RCTRL/TCTRL. The attempt to lock these
operations doesn't help, but only adds to the confusion.
There's also a dependency for Rx FCB insertion (activating
/de-activating the TOE offload block on Rx) which might
change the required rx buffer size. This makes matters
worse as gfar_vlan_mode() ends up calling gfar_change_mtu(),
though the MTU size remains the same. Note that there are
other situations that may affect the required rx buffer size,
like changing RXCSUM or rx hw timestamping, but errorneously
the rx buffer size is not recomputed/ updated in the process.
To fix this, do the vlan updates properly inside the MAC
reset and reconfiguration procedure, which takes care of
the rx buffer size dependecy and the rx TOE block (PRSDEP)
activation/deactivation as well (in the correct order).
As a consequence, MTU/ rx buff size updates are done now
by the same MAC reset and reconfig procedure, so that out
of context updates to MAXFRM, MRBLR, and MACCFG inside
change_mtu() are no longer needed. The rx buffer size
dependecy to Rx FCB is now handled for the other cases too
(RXCSUM and rx hw timestamping).
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The main MAC config registers like: RCTRL/TCTRL, MRBLR,
MAXFRM, RXIC/TXIC, most fields of MACCFG1/2, should not
be changed on-the-fly, but at least after stopping the
DMA and disabling the Rx/Tx blocks and, for increased
reliability, after a MAC soft reset.
Impelement a complete MAC soft reset and reconfig procedure
following the latest HW advisories - gfar_mac_reset() - to
replace gfar_mac_init() and (the confusing) init_registers()
functions.
Factor out separate config functions for RCTRL and TCTRL,
insure programming order of the relevant config regs after
MAC soft reset.
Split gfar_hw_init() into gfar_mac_reset() and the remaining
global regs that don't need to be reconfigured after MAC soft
reset (FIFOCFG, ATTRELI, HW counters a.s.o).
As gfar_hw_init() now makes all the register writes @probe()
time, based on all the device flags and config options, it
must be moved further down, just before register_netdev(),
as the last config step when the config values are comitted
to HW. Also, move netif_carrier_off() after register_netdev(),
because it has no effect if called before.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current flow: Set TX BD ready, and then set "INT" and "PINS" bit to
enable tx interrupt generation and crc checksum.
There has potential issue like as:
CPU fec uDMA
Set tx ready bit
uDMA start the BD transmission
Set "INT" bit
Set "PINS" bit
...
Above situation cause fec tx interrupt lost and fec MAC don't do
CRC checksum. The patch fix the potential issue.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Acked-by: Frank Li <Frank.li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/bonding/bond_3ad.h
drivers/net/bonding/bond_main.c
Two minor conflicts in bonding, both of which were overlapping
changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
If napi is left enabled after a failed attempt to bring the interface
up, we BUG:
fec 2188000.ethernet eth0: no PHY, assuming direct connection to switch
libphy: PHY fixed-0:00 not found
fec 2188000.ethernet eth0: could not attach to PHY
------------[ cut here ]------------
kernel BUG at include/linux/netdevice.h:502!
Internal error: Oops - BUG: 0 [#1] SMP ARM
...
PC is at fec_enet_open+0x4d0/0x500
LR is at __dev_open+0xa4/0xfc
Only enable napi after we are past all the failure paths.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
gfar_clean_rx_ring() was designed to be called from napi
(rx softirq) context to do the Rx processing. Calling it
from a process context like this is a bug as it will
clearly race with the napi Rx processing.
There's also no point in initializing num_txbdfree since
startup_gfar() already does that, when bringing the device
up again (after reset). Changing num_txbdfree "on-the-fly"
like this is also subject to race conditions. num_txbdfree
is handled by the Tx processing path and the device reset
procedure. Also, don't assume that num_rx_queues is always
equal to num_tx_queues.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
gfar_halt() and gfar_start() are responsible for stopping
and starting the DMA and the Rx/Tx hw rings. They implement
the support for the "graceful Rx/Tx stop/start" hw procedure,
and also disable/enable eTSEC's hw interrupts in the process.
The GRS/GTS procedure requires however to have the RQUEUE/TQUEUE
registers cleared first and to wait for a period of time for the
current frame to pass through the interface (around ~10ms for a
jumbo frame). Only then may the GTS and GRS bits from DMACTRL be
set to shut down the DMA, and finally the Tx_EN and Rx_EN bits in
MACCFG1 may be cleared to disable the Tx/Rx blocks.
The same register programming order applies to start the Rx/Tx:
enabling the RQUEUE/TQUEUE *before* clearing the GRS/GTS bits.
This is a HW recommendation in order to avoid a possible
controller "lock up" during graceful reset.
Cleanup the gfar_halt()/start() prototypes, to take priv instead
of ndev as their purpose is to operate on HW. Enabling the
RQUEUE/TQUEUE in the hw_init() is not needed anymore since
that's the job of gfar_start().
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Throughout the code there are places where the controller's
hw interrupt sources need to get disabled/enabled (masked/
un-masked) all at once. The recommendation for disabling
the interrupts is to clear the ievent first then the imask
register (not the other way around).
Use the gfar_ints_enable/disable() helpers to make these
operations consistent.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds
Nimrod Andy
Andy Fleming
Shruti Kanetkar
David S. Miller
Fabio Estevam
Xiubo Li
Florian Fainelli
Wilfried Klaebe
Claudiu Manoil
Peter Zijlstra
Lucas Stach
Eric W. Biederman
Richard Cochran
Stefan Wahren
Russell King