Baikal-T1 PVT sensor has got a dedicated power supply domain (feed up by
the external GPVT/VPVT_18 pins). In case if it isn't powered up, the
registers will be accessible, but the sensor conversion just won't happen.
Due to that an attempt to read data from any PVT sensor will cause the
task hanging up. For instance that will happen if XP11 jumper isn't
installed on the Baikal-T1-based BFK3.1 board. Let's at least test whether
the conversion work on the device probe procedure. By doing so will make
sure that the PVT sensor is powered up at least at boot time.
Fixes: 87976ce282 ("hwmon: Add Baikal-T1 PVT sensor driver")
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20200920110924.19741-2-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add regulator support for boards where the sensor first need to be
powered up before it can be used.
Signed-off-by: Alban Bedel <alban.bedel@aerq.com>
Link: https://lore.kernel.org/r/20201001145738.17326-4-alban.bedel@aerq.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This patch adds hwmon functionality for Intel MAX 10 BMC chip. This BMC
chip connects to a set of sensor chips to monitor current, voltage,
thermal and power of different components on board. The BMC firmware is
responsible for sensor data sampling and recording in shared registers.
Host driver reads the sensor data from these shared registers and
exposes them to users as hwmon interfaces.
Signed-off-by: Xu Yilun <yilun.xu@intel.com>
Signed-off-by: Wu Hao <hao.wu@intel.com>
Signed-off-by: Matthew Gerlach <matthew.gerlach@linux.intel.com>
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/1600669071-26235-3-git-send-email-yilun.xu@intel.com
[groeck: Adjusted subject]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for mp295 device from Monolithic Power Systems, Inc. (MPS)
vendor. This is a dual-loop, digital, multi-phase controller.
This device:
- Supports two power rail.
- Provides 8 pulse-width modulations (PWMs), and can be configured up
to 8-phase operation for rail 1 and up to 4-phase operation for rail
2.
- Supports two pages 0 and 1 for telemetry and also pages 2 and 3 for
configuration.
- Can configured VOUT readout in direct or VID format and allows
setting of different formats on rails 1 and 2. For VID the following
protocols are available: VR13 mode with 5-mV DAC; VR13 mode with
10-mV DAC, IMVP9 mode with 5-mV DAC.
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Link: https://lore.kernel.org/r/20200926204957.10268-2-vadimp@nvidia.com
[groeck: Cleaned up a couple of error returns; fixed up API changes]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Update the documentation with the newly added features
* Set the accumulation interval based on resolution
Signed-off-by: Naveen Krishna Chatradhi <nchatrad@amd.com>
Link: https://lore.kernel.org/r/20200929105322.8919-5-nchatrad@amd.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Factor out the common code in the accumulation functions for core and
socket accumulation.
While at it, handle the return value of the amd_create_sensor() function.
Signed-off-by: Naveen Krishna Chatradhi <nchatrad@amd.com>
Link: https://lore.kernel.org/r/20200929105322.8919-4-nchatrad@amd.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
On a system with course grain resolution of energy unit (milli J) the
accumulation thread can be executed less frequently than on the system
with fine grain resolution(micro J).
This patch sets the accumulation thread interval to an optimum value
calculated based on the (energy unit) resolution supported by the
hardware (assuming a peak wattage of 240W).
Signed-off-by: Naveen Krishna Chatradhi <nchatrad@amd.com>
Link: https://lore.kernel.org/r/20200929105322.8919-3-nchatrad@amd.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
At present, core & socket labels are defined in struct sensor_accumulator
This patch moves it to the amd_energy_data structure, which will
help in calling memset on struct sensor_accumulator to optimize the code.
Signed-off-by: Akshay Gupta <Akshay.Gupta@amd.com>
Link: https://lore.kernel.org/r/20200929105322.8919-2-nchatrad@amd.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Convert the adm9240 driver to using regmap and add error handling.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Link: https://lore.kernel.org/r/20200924085102.15219-4-chris.packham@alliedtelesis.co.nz
[groeck: Fixed context conflict against 'hwmon: use simple i2c probe function']
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Split the body of adm9240_update_device() into two helper functions
adm9240_update_measure() and adm9240_update_config(). Although neither
of the new helpers returns an error yet lay the groundwork for
propagating failures through to the sysfs readers.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Link: https://lore.kernel.org/r/20200924085102.15219-3-chris.packham@alliedtelesis.co.nz
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Zen3 thermal info is supported via a new PCI device ID. Also the voltage
telemetry registers and the current factors need to be defined. k10temp
driver then searches for CPU family 0x19 and configures k10temp_data
accordingly.
Signed-off-by: Wei Huang <wei.huang2@amd.com>
Link: https://lore.kernel.org/r/20200914200715.1997757-1-wei.huang2@amd.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
0-day rightfully complains about a sometimes uninitialized variable
in pmbus_get_boolean().
drivers/hwmon/pmbus/pmbus_core.c:903:13: warning:
variable 'ret' is used uninitialized whenever 'if' condition is true
} else if (!s1 || !s2) {
While that is technically true, it won't be hit in the field since the
condition indicates a programming error. Move the check of that condition
into the code generating the attribute entry, and refuse generating the
attribute if the condition is true. Swap the condition check in
pmbus_get_boolean() to ensure that static analyzers don't get a hiccup
(because we check if s1 and s2 are NULL, static analyzers may believe
that they can be NULL independently of each other).
Reported-by: kernel test robot <lkp@intel.com>
Cc: Alex Qiu <xqiu@google.com>
Reviewed-by: Alex Qiu <xqiu@google.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Enable runtime debug control of whether the PEC byte is exchanged with
the PMBus device.
Some manufacturers have asked for the PEC to be disabled as part of
debugging driver communication issues with devices.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20200910021106.2958382-1-andrew@aj.id.au
[groeck: Replace %1llu with %llu]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Caching register values can be very expensive for PMBus chips. Some
modern chips may have 10 or more pages, with several sensors supported
per page. For example, MAX16601 creates more than 90 sysfs attributes.
Register caching for such chips is time consuming, especially if only a
few attributes are read on a regular basis. For MAX16601, it was observed
that it can take up to two seconds to read all attributes on a slow I2C
bus. In this situation, register caching results in the opposite of its
intention: It increases the number of I2C operations, in some cases
substantially, and it results in large latency when trying to access
individual sensor data.
Drop all register caching to solve the problem. Since it is no longer
necessary, drop status register mapping as part of the change, and specify
status registers directly.
Cc: Alex Qiu <xqiu@google.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Alex Qiu <xqiu@google.com>
Tested-by: Alex Qiu <xqiu@google.com>
Link: https://lore.kernel.org/r/20200904163314.259087-1-linux@roeck-us.net
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The debugfs code was intended to aid figuring out functionality
of undocumented registers. Turns out that wasn't very helpful,
since register locations change too much between AMD chip revisions,
and the data isn't really valuable for chips where it isn't already
supported. On top of that, its existence has been used as argument
for providing pseudo-API debugfs functions in other drivers.
So let's just take it out.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add a fan sensor to report RPM's from a fan tach input.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The voltage telemetry registers for Zen2 are different from Zen1. Also
the factors of CPU current values are changed on Zen2. Add new definitions
for these register.
Signed-off-by: Wei Huang <wei.huang2@amd.com>
Link: https://lore.kernel.org/r/20200827054242.2347-2-wei.huang2@amd.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Many SMN thermal registers in Zen CPU families are common across different
generations. For long-term code maintenance, it is better to rename these
macro and function names to Zen.
Signed-off-by: Wei Huang <wei.huang2@amd.com>
Link: https://lore.kernel.org/r/20200827054242.2347-1-wei.huang2@amd.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use the nvmem kernel api to expose the black box
chip functionality to userspace.
Using this feature, the device is capable of recording
to nonvolatile flash memory the vital data about the
system status that caused the system to perform a
black box write.
A blackbox is 64 bytes of data containing all the
status registers, last two states of the sequencer,
timestamp and counters. The mapping of this data is
described in the adm1266 datasheet.
On power-up the driver sets the unix time to
the adm1266 using the SET_RTC command. This value
is incremented by an internal clock and it is used
as timestamp for the black box feature.
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Link: https://lore.kernel.org/r/20200812142055.9213-6-alexandru.tachici@analog.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Adm1266 exposes 9 GPIOs and 16 PDIOs which are currently read-only. They
are controlled by the internal sequencing engine.
This patch makes adm1266 driver expose GPIOs and PDIOs to user-space
using GPIO provider kernel api.
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Link: https://lore.kernel.org/r/20200812142055.9213-4-alexandru.tachici@analog.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
PmBus devices support Block Write-Block Read Process
Call described in SMBus specification v 2.0 with the
exception that Block writes and reads are permitted to
have up 255 data bytes instead of max 32 bytes (SMBus).
This patch adds Block WR process call support for ADM1266.
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Link: https://lore.kernel.org/r/20200812142055.9213-3-alexandru.tachici@analog.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add pmbus probing driver for the adm1266 Cascadable
Super Sequencer with Margin Control and Fault Recording.
Driver is using the pmbus_core, creating sysfs files
under hwmon for inputs: vh1->vh4 and vp1->vp13.
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Link: https://lore.kernel.org/r/20200812142055.9213-2-alexandru.tachici@analog.com
[groeck: Use .probe_new function, adjust for changed pmbus_do_probe API]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add documentation for the newly added DTS support in the shtc1 driver.
To align with the drivers logic to have high precision by default
a boolean sensirion,low-precision is used to switch to low precision.
Signed-off-by: Chris Ruehl <chris.ruehl@gtsys.com.hk>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20200815012227.32538-3-chris.ruehl@gtsys.com.hk
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for DTS bindings for the sensirion shtc1,shtw1 and shtc3.
Signed-off-by: Chris Ruehl <chris.ruehl@gtsys.com.hk>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20200815012227.32538-2-chris.ruehl@gtsys.com.hk
[groeck: Resolved conflicts]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
As part of the ongoing i2c transition to the simple probe
("probe_new"), this patch uses i2c_match_id to retrieve the
driver_data for the probed device. The id parameter is thus no longer
necessary and the simple probe can be used instead.
Signed-off-by: Stephen Kitt <steve@sk2.org>
Link: https://lore.kernel.org/r/20200821160035.590142-1-steve@sk2.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
As part of the ongoing i2c transition to the simple probe
("probe_new"), this patch uses i2c_match_id to retrieve the
driver_data for the probed device. The id parameter is thus no longer
necessary and the simple probe can be used instead.
Signed-off-by: Stephen Kitt <steve@sk2.org>
Link: https://lore.kernel.org/r/20200821160159.591293-1-steve@sk2.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
As part of the ongoing i2c transition to the simple probe
("probe_new"), this patch uses i2c_match_id to retrieve the
driver_data for the probed device. The id parameter is thus no longer
necessary and the simple probe can be used instead.
Signed-off-by: Stephen Kitt <steve@sk2.org>
Link: https://lore.kernel.org/r/20200821160231.592571-1-steve@sk2.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Many hwmon drivers don't use the id information provided by the old
i2c probe function, and the remainder can easily be adapted to the new
form ("probe_new") by calling i2c_match_id explicitly.
This avoids scanning the identifier tables during probes.
Drivers which didn't use the id are converted as-is; drivers which did
are modified to call i2c_match_id() with the same level of
error-handling (if any) as before.
This patch wraps up the transition for hwmon, with four stragglers not
included in the previous large patch.
Signed-off-by: Stephen Kitt <steve@sk2.org>
Link: https://lore.kernel.org/r/20200821160354.594715-1-steve@sk2.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This driver doesn't use the id information provided by the old i2c
probe function, so it can trivially be converted to the simple
("probe_new") form.
Signed-off-by: Stephen Kitt <steve@sk2.org>
Link: https://lore.kernel.org/r/20200813162851.1519546-1-steve@sk2.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This driver doesn't use the id information provided by the old i2c
probe function, so it can trivially be converted to the simple
("probe_new") form.
Signed-off-by: Stephen Kitt <steve@sk2.org>
Link: https://lore.kernel.org/r/20200813162704.1517951-1-steve@sk2.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This driver doesn't use the id information provided by the old i2c
probe function, so it can trivially be converted to the simple
("probe_new") form.
Signed-off-by: Stephen Kitt <steve@sk2.org>
Link: https://lore.kernel.org/r/20200813162544.1516647-1-steve@sk2.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This driver doesn't use the id information provided by the old i2c
probe function, so it can trivially be converted to the simple
("probe_new") form.
Signed-off-by: Stephen Kitt <steve@sk2.org>
Link: https://lore.kernel.org/r/20200813162300.1514695-1-steve@sk2.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This driver doesn't use the id information provided by the old i2c
probe function, so it can trivially be converted to the simple
("probe_new") form.
Signed-off-by: Stephen Kitt <steve@sk2.org>
Link: https://lore.kernel.org/r/20200813162026.1512242-1-steve@sk2.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This driver doesn't use the id information provided by the old i2c
probe function, so it can trivially be converted to the simple
("probe_new") form.
Signed-off-by: Stephen Kitt <steve@sk2.org>
Link: https://lore.kernel.org/r/20200813161845.1511261-1-steve@sk2.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This driver doesn't use the id information provided by the old i2c
probe function, so it can trivially be converted to the simple
("probe_new") form.
Signed-off-by: Stephen Kitt <steve@sk2.org>
Acked-by: Corentin LABBE <clabbe.montjoie@gmail.com>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Link: https://lore.kernel.org/r/20200813161129.1507599-1-steve@sk2.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This driver doesn't use the id information provided by the old i2c
probe function, so it can trivially be converted to the simple
("probe_new") form.
Signed-off-by: Stephen Kitt <steve@sk2.org>
Link: https://lore.kernel.org/r/20200813160958.1506536-1-steve@sk2.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Many hwmon drivers don't use the id information provided by the old
i2c probe function, and the remainder can easily be adapted to the new
form ("probe_new") by calling i2c_match_id explicitly.
This avoids scanning the identifier tables during probes.
Drivers which didn't use the id are converted as-is; drivers which did
are modified as follows:
* if the information in i2c_client is sufficient, that's used instead
(client->name);
* anything else is handled by calling i2c_match_id() with the same
level of error-handling (if any) as before.
A few drivers aren't included in this patch because they have a
different set of maintainers. They will be covered by other patches.
Signed-off-by: Stephen Kitt <steve@sk2.org>
Link: https://lore.kernel.org/r/20200813160222.1503401-1-steve@sk2.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
pmbus_do_probe doesn't use the id information provided in its second
argument, so this can be removed, which then allows using the
single-parameter i2c probe function ("probe_new") for probes.
This avoids scanning the identifier tables during probes.
Drivers which didn't use the id are converted as-is; drivers which did
are modified as follows:
* if the information in i2c_client is sufficient, that's used instead
(client->name);
* configured v. probed comparisons are performed by comparing the
configured name to the detected name, instead of the ids; this
involves strcmp but is still cheaper than comparing all the device
names when scanning the tables;
* anything else is handled by calling i2c_match_id() with the same
level of error-handling (if any) as before.
Additionally, the mismatch message in the ltc2978 driver is adjusted
so that it no longer assumes that the driver_data is an index into
ltc2978_id.
Signed-off-by: Stephen Kitt <steve@sk2.org>
Acked-by: Wolfram Sang <wsa@kernel.org>
Link: https://lore.kernel.org/r/20200808210004.30880-1-steve@sk2.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
On some drives, reading the drive temperature resets the drive's
spin-down timer. If the drive temperature is read too often, affected
drives will never spin down. Add this information as usage note to
the driver documentation.
Reported-by: Peter Sulyok <peter@sulyok.net>
Cc: Peter Sulyok <peter@sulyok.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Adding implementation for new attributes (rated_min/rated_max) to
cover PMBus specification about rated values reporting:
MFR_VIN_MIN, MFR_VIN_MAX, MFR_IIN_MAX, MFR_PIN_MAX, MFR_VOUT_MIN,
MFR_VOUT_MAX, MFR_IOUT_MAX, MFR_POUT_MAX, MFR_MAX_TEMP_1/2/3.
Tested with OpenBMC stack. All rated attributes were available
and reported correct values.
Signed-off-by: Zbigniew Lukwinski <zbigniew.lukwinski@linux.intel.com>
Link: https://lore.kernel.org/r/1596224237-32280-4-git-send-email-zbigniew.lukwinski@linux.intel.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Adding implementation for new attributes (rated_min/rated_max) for
currentX, inX, powerX, tempX and humidityX.
Tested with OpenBMC stack and simple hwmon driver using
rated_min/rated_max for the following types of sensors: hwmon_temp,
hwmon_in, hwmon_curr, hwmon_power, hwmon_humidity.
For each sensor rated attributes were available and returned
expected values.
Signed-off-by: Zbigniew Lukwinski <zbigniew.lukwinski@linux.intel.com>
Link: https://lore.kernel.org/r/1596224237-32280-3-git-send-email-zbigniew.lukwinski@linux.intel.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
New attributes (rated_min/rated_max) are being added the hwmon ABI.
They are needed to cover rated values documented by PMBus
specification:
PMBus Power System Mgt Protocol Specification - Part II – Revision 1.3.1,
chapters: 22.3.1 - 22.3.10, 22.3.15
Signed-off-by: Zbigniew Lukwinski <zbigniew.lukwinski@linux.intel.com>
Link: https://lore.kernel.org/r/1596224237-32280-2-git-send-email-zbigniew.lukwinski@linux.intel.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Smatch has a new check for resource leaks which found a bug in probe:
drivers/hwmon/w83627ehf.c:2417 w83627ehf_probe()
warn: 'res->start' not released on lines: 2412.
We need to clean up if devm_hwmon_device_register_with_info() fails.
Fixes: 266cd58359 ("hwmon: (w83627ehf) convert to with_info interface")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Dr. David Alan Gilbert <linux@treblig.org>
Link: https://lore.kernel.org/r/20200921125212.GA1128194@mwanda
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Serge Semin
Alban Bedel
Xu Yilun
Vadim Pasternak
Wang Qing
Naveen Krishna Chatradhi
Akshay Gupta
Chris Packham
Wei Huang
Guenter Roeck
Andrew Jeffery
Tim Harvey
Joe Perches
Alexandru Tachici
Chris Ruehl
Anson Huang
Stephen Kitt
Zbigniew Lukwinski
Dan Carpenter