This is based on Michal Schmidt fix for skge.
Most network drivers request their IRQ when the interface is activated.
sky2 does it in ->probe() instead, because it can work with two-port
cards where the two net_devices use the same IRQ. This works fine most
of the time, except in some situations when the interface gets renamed.
Consider this example:
1. modprobe sky2
The card is detected as eth0 and requests IRQ 17. Directory
/proc/irq/17/eth0 is created.
2. There is an udev rule which says this interface should be called
eth1, so udev renames eth0 -> eth1.
3. modprobe 8139too
The Realtek card is detected as eth0. It will be using IRQ 17 too.
4. ip link set eth0 up
Now 8139too requests IRQ 17.
The result is:
WARNING: at fs/proc/generic.c:590 proc_register ...
proc_dir_entry '17/eth0' already registered
The fix is for sky2 to name the irq based on the pci device, as is done
by some other devices DRM, infiniband, ... ie. sky2@pci:0000:00:00
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Reviewed-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SKY2_HW_RAM_BUFFER bit in hw->flags was checked in sky2_mac_init(),
before being set later in sky2_up().
Setting SKY2_HW_RAM_BUFFER in sky2_init() where other hw->flags are set
should avoid this problem recurring.
Signed-off-by: Mike McCormack <mikem@ring3k.org>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sorry Mike, I sent you off the wrong way. The following is simpler and the
second port is diffrent enough in setup (because of NAPI), that the
following is simpler.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Be more accurate about number of transmit list elements required.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_ioctl() already checks capable(CAP_NET_ADMIN) before calling the
driver's implementation of MDIO ioctls.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While perusing vendor driver, I saw that it did not enable the Vaux
power unless device was able to wake from lan for D3cold.
This might help for Rene's power issue.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
B0_CTST is a 24bit register according to the vendor driver (sk98lin).
A 16bit read on B0_CTST will always return 0 for Y2_VAUX_AVAIL (1<<16),
so use a 32bit read when testing Y2_VAUX_AVAIL
Signed-off-by: Mike McCormack <mikem@ring3k.org>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor similar two sections of code that free buffers into one.
Only call tx_init if all buffer allocations succeed.
Signed-off-by: Mike McCormack <mikem@ring3k.org>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Observed by Mike McCormack.
The LED bit here is just a software controlled value used to
turn on one of the LED's on some boards. The register value was wrong,
which could have been causing some power control issues.
Get rid of problematic define use the correct mask.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a couple of cases collapse some extra code like:
int retval = NETDEV_TX_OK;
...
return retval;
into
return NETDEV_TX_OK;
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recycling turns out to be a bad idea! For most use cases, the
packet can not be reused: TCP packets are cloned. Even for the ideal
case of forwarding, it hurts performance because of CPU ping/pong.
On a multi-core system forwarding of 64 byte packets is worse
much worse: recycling = 24% forwarded vs no recycling = 42% forwarded
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't reference the list element in hardware transmit ring on transmit
completion. The list element is updated by hardware, therefore
it causes a cache miss. Do book keeping in software structure.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allocate and size transmit ring based on parameters. Saves excess
space and allows configuring larger rings for testing.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code for list element error (which should only happen on hardware
errors) should be cleaner and safer. Gets rid of unused ring_size
argument, which makes next patch easier.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch saves elements on transmit ring by only updating the upper
64 bit address when it changes. With many workloads skb's are located
in same region, so it saves space.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the existing macros to show where DMA address is being broken
apart. This is cosmetic only.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The whole restarting flag was introduced by Mike McCormack
and was a temporary duct tape patch around issues with transmits
inflight during restart. The problems it was covering are now
fixed and the code should have been reverted.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sky2 driver combines auto speed negotiation with automatic negotiation
of pause parameters; but the ethtool interface expects them to be
split. This patch allows autonegotiation to be used for speed, but
manually disable flow control.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Transmit completion can safely run lockless against transmit start.
In the normal case, completion is done from NAPI and only looks
at elements that are at the tail of the ring. When doing shutdown
or reset, the transmiter should be completely block by NAPI disable
and blocking of transmit queue.
Based on earlier work by Mike McCormack.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This unifies the places that bounce the device (suspend/resume
and restart). And makes the operations have the same semantics
as normal dev_open/dev_stop.
This also avoids setting the multicast addresses twice when
device is brought up.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The suspend and shutdown code plays with shared state. Use consistent
locking, for extra protection.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid any possible problems with accessing PHY registers on shutdown.
This is a purely theoretical issue and is not related to any of the
outstanding bug reports. Since receiver and transmitter are already
shutdown and phy interrupts for this device are already disabled,
there should already be enough protection. Suggested by Mike McCormack.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reseting the tx chain too soon results in invalid tx queue positions
being delivered in the status queue. This also makes sure there's no
overlap between the cleanup done by sky2_tx_clean() and
sky2_tx_done().
Signed-off-by: Mike McCormack <mikem@ring3k.org>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is pure refactoring.
Signed-off-by: Mike McCormack <mikem@ring3k.org>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Keep sky2->tx_prod consistent since int might be examined by
an softirq poll or restart.
Signed-off-by: Mike McCormack <mikem@ring3k.org>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch supersedes my previous patch "sky2: Avoid transmitting
during sky2_restart".
I have reworked the patch to avoid crashes during both sky2_restart()
and sky2_set_ringparam().
Without this patch, the sky2 driver can be crashed by doing:
# pktgen eth1 & (transmit many packets on eth1)
# ethtool -G eth1 tx 510
I am aware you object to storing extra state, but I can't see a way
around this. Without remembering that we're restarting,
netif_wake_queue() is called in the ISR from sky2_tx_complete(), and
netif_tx_lock() is used in sky2_tx_done(). If anybody can see a way
around this, please let me know.
Signed-off-by: Mike McCormack <mikem@ring3k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Mike McCormack <mikem@ring3k.org>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reset rx chain before trying to drain it.
Shut interrupts off last, incase there's something to report.
Signed-off-by: Mike McCormack <mikem@ring3k.org>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit changes to shutdown path broke startup on some systems.
revert commit c0bad0f2e4
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sky2 driver on PowerPC targets floods kernel log with following errors:
eth1: hw csum failure.
Call Trace:
[ef84b8a0] [c00075e4] show_stack+0x50/0x160 (unreliable)
[ef84b8d0] [c02fa178] netdev_rx_csum_fault+0x3c/0x5c
[ef84b8f0] [c02f6920] __skb_checksum_complete_head+0x7c/0x84
[ef84b900] [c02f693c] __skb_checksum_complete+0x14/0x24
[ef84b910] [c0337e08] tcp_v4_rcv+0x4c8/0x6f8
[ef84b940] [c031a9c8] ip_local_deliver+0x98/0x210
[ef84b960] [c031a788] ip_rcv+0x38c/0x534
[ef84b990] [c0300338] netif_receive_skb+0x260/0x36c
[ef84b9c0] [c025de00] sky2_poll+0x5dc/0xcf8
[ef84ba20] [c02fb7fc] net_rx_action+0xc0/0x144
The NIC is Yukon-2 EC chip revision 1.
Converting checksum field from le16 to CPU byte order fixes the issue.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements skb recycling. It reclaims transmitted skb's
for use in the receive ring.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reduce the size of the driver transmit ring to reduce latency
and allow qdisc to do better rate control. Also make it
obvious what the minimum transmit ring allowed is and why.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since it is likely that there are multiple packets received per
interrupt, only update the receive counters once after all
packets are processed.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The logic in sky2_down was incorrect. Receiver could report status
after rx_stop was called.
The steps need to be:
* stop new frames from being transmitted
* shut off transmit/receive logic
* synchronize with NAPI to process status info about transmitter
and receiver
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add some read's to avoid any PCI posting issues when controlling
irq's.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reset more parts of the receive path when device is take offline.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This unblocks the chip if it is stuck in pause cycle during
shutdown.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code to compute VPD size didn't handle some systems that use
chip without VPD. Also some of the newer chips use some additional
registers to store the actual size, and wasn't worth putting the
additional complexity in, so just remove the code.
No big loss since the code to set the VPD size was only a
convenience so that utilities would not read the extra space past
the end of the available VPD.
Move the first PCI config read earlier to detect bad hardware
where it returns all ones and refuse loading driver before furthur
damage.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Tested-by: Andy Whitcroft <apw@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Second round of drivers for Gb cards (and NIU one I forgot in the 10GB round)
Now that core network takes care of trans_start updates, dont do it
in drivers themselves, if possible. Drivers can avoid one cache miss
(on dev->trans_start) in their start_xmit() handler.
Exceptions are NETIF_F_LLTX drivers
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace all DMA_32BIT_MASK macro with DMA_BIT_MASK(32)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace all DMA_64BIT_MASK macro with DMA_BIT_MASK(64)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Read configuration register during probe and use it to size the
available VPD. Move existing code using same register slightly
earlier in probe handling.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The VPD stuff has more data and isn't generally that useful, so move
it into the existing debugfs display and use the new PCI VPD
accessor routines.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On non-x86 platforms it is possible to run out of DMA mapping resources.
The driver was ignoring this and could cause corruptions.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This workaround is not needed. It was inherited from sk98lin driver but only
applies to an early development version of the chip that is not supported
by sky2. The workaround required an unnecessary pci read which hurts performance
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Printing anything over netconsole before hw is up and running is,
of course, not going to work.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves neigh_setup and hard_start_xmit into the network device ops
structure. For bisection, fix all the previously converted drivers as well.
Bonding driver took the biggest hit on this.
Added a prefetch of the hard_start_xmit in the fast path to try and reduce
any impact this would have.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert to new network device ops interface. Slight additional complexity
here because the second port does not allow netpoll and therefore has
different virtual function table.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This converts pretty much everything to print_mac. There were
a few things that had conflicts which I have just dropped for
now, no harm done.
I've built an allyesconfig with this and looked at the files
that weren't built very carefully, but it's a huge patch.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since dev->power.should_wakeup bit is used by the PCI core to
decide whether the device should wake up the system from sleep
states, set/unset this bit whenever WOL is enabled/disabled using
sky2_set_wol().
Remove an open-coded reference to the standard PCI PM registers that
is not used any more.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change bootup messages to print more information. This is to help users
who may have old buggy EEPROM image.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Cleanup and harden the routines accessing the EEPROM.
1. Prevent spin forever waiting for the TWSI bus
2. Fix write eeprom to write full words rather than only 16 bits
Luckly the vendor doesn't provide EEPROM in Linux format so it must never
have been used.
3. Don't allow partial eeprom writes, not needed, not safe.
These are non-urgent bug fixes.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
On my test box with the Asus M3A32-MVP main board there is a
regression from 2.6.26 related to suspend, hibernation and
shutdown. Namely, if Wake-on-LAN is enabled with
'ethtool -s eth0 wol g', the box hangs solid during all of these
operations, while executing either sky2_suspend(), or
sky2_shutdown(). This patch fixes it for me.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The drivers below do not use LINUX_VERSION_CODE nor KERNEL_VERSION.
drivers/net/acenic.c
drivers/net/bnx2x_link.c
drivers/net/bnx2x_main.c
drivers/net/cpmac.c
drivers/net/gianfar_sysfs.c
drivers/net/ipg.h
drivers/net/ppp_mppe.c
drivers/net/pppol2tp.c
drivers/net/r6040.c
drivers/net/sh_eth.c
drivers/net/sky2.c
drivers/net/tehuti.h
drivers/net/typhoon.c
This patch removes the said #include <linux/version.h>.
Signed-off-by: Huang Weiyi <hwy@cn.fujitsu.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fix the problems reported for 2.6.27-rc1 caused by over aggressive
power management. Turning clock off on PCI Express is problematic for WOL,
and when doing multi-booting.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
It is unnecessary, to stop queue and turn off carrier in shutdown
routine. With new netdev_queue this causes warnings.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for Yukon 2 Ultra 2 chip set (88E8057) based on code in latest
version of vendor driver (sk98lin 10.60.2.3). Untested on real hardware.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
PCI device table can be marked as devinitconst by using macro.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Change how chip version is printed so that if an unknown version is detected
nothing breaks.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Change the setup of the PHY registers on some chip ids. These changes
make the latest sky2 driver follow the vendor driver.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Turn on special bits to save more power when device is shutdown.
Tested on a limited range of hardware, some of the bits are for hardware
that probably isn't even in production (like Yukon Supreme) and was ported
from the vendor driver.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Put PHY int sleep mode (from vendor sk98lin 10.50 driver) when the
network device is brought down.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Later changes add more code to PHY power changes so refactor now.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
If device has to be reset by sky2_restart, then need to restore
the VLAN acceleration settings.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Any usage of sky2 on new Yukon Supreme would cause a NULL dereference.
The chip is very new, so the support is still untested; vendor has
not sent any eval hardware.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
There are a couple of possible races on suspend/resume.
First the driver needs to block new packets from being queued for Tx.
The other less likely problem is the watchdog timer going off
during resume.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix problems in LED management, so ethtool -p works correctly on Yukon-EC
and other chips. The driver was incorrectly setting the PHY LED overide bits.
Moral: read the spec sheet, not the vendor driver.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The Yukon FE chip has a ram buffer therefore it needs the alignment
restriction and hang check workarounds.
Therefore:
* Autodetect the prescence/absence of ram buffer
* Rename the flag value to reflect this
* Use it consistently (ie don't reread register)
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch disables config mode access after clearing PCI settings.
Some BIOS's seem to not do WOL if config bit still set.
Fixes: http://bugzilla.kernel.org/show_bug.cgi?id=9721
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the sky2 deadman timer forces a recovery, the multicast hash
list is lost. Move the call to sky2_set_multicast to the end
of sky2_up() so all paths that bring device up will restore multicast.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update driver version reflects new hardware support.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add support from sk98lin vendor driver 10.50.1.3 for 88E8055 and
88E8075 chips. I don't have this hardware to test, so this changes
are untested.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
When using larger MTU's sky2 driver changes from allocating one
data area, to using multiple pages. The threshold for this was based on
a heuristic where the cost of a single allocation is bigger than one
page. Since the allocator has changed, this heuristic is now incorrect;
instead just make the threshold be when the total size of the allocation
is greater than one page.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The sky2 driver was not aligning the IP header on receive buffers.
This workaround is only needed on hardware with broken FIFO, newer chips
without FIFO can just DMA to unaligned address.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This reverts commit 84cd2dfb04.
Some BIOS's break if Wake On Lan is enabled, and the machine
can't boot. Better to have some user's have to call ethtool to
enable WOL than to break a single user's boot.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The driver checks status of PCI power management to mark
default setting of Wake On Lan. On some systems this works, but often
it reports a that WOL is disabled when it isn't.
This patch gets rid of that check and just reports the wake on
lan status based on the hardware capablity.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch might fix problems with 4G or more of memory.
It stops the driver from doing a small optimization for Tx and Rx,
and instead always sets the high-page on tx/rx descriptors.
Fixes-bug: http://bugzilla.kernel.org/show_bug.cgi?id=9725
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
When we add the generic napi_disable_pending() breakout
logic to net_rx_action() it means that napi_disable()
can cause NAPI poll interrupt events to be disabled.
And this is exactly what we want. If a napi_disable()
is pending, and we are looping in the ->poll(), we want
->poll() event interrupts to stay disabled and we want
to complete the NAPI poll ASAP.
When ->poll() break out during device down was being handled on a
per-driver basis, often these drivers would turn interrupts back on
when '!netif_running()' was detected.
And this would just cause a reschedule of the NAPI ->poll() in the
interrupt handler before the napi_disable() could get in there and
grab the NAPI_STATE_SCHED bit.
The vast majority of drivers don't care if napi_disable() might have
the side effect of disabling NAPI ->poll() event interrupts. In all
such cases, when a napi_disable() is performed, the driver just
disabled interrupts or is about to.
However there were three exceptions to this in PCNET32, R8169, and
SKY2. To fix those cases, at the subsequent napi_enable() points, I
added code to ensure that the ->poll() interrupt events are enabled in
the hardware.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Don Fry <pcnet32@verizon.net>
I'm using a Marvell 88E8062 on a custom PPC64 blade and ran into RX
lockups while validating the sky2 driver. The receive MAC FIFO would
become stuck during testing with high traffic. One port of the 88E8062
would lockup, while the other port remained functional. Re-inserting
the sky2 module would not fix the problem - only a power cycle would.
I looked over Marvell's most recent sk98lin driver and it looks like
they had a "workaround" for the Yukon XL that the sky2 doesn't have yet.
The sk98lin driver disables the RX MAC FIFO flush feature for all
revisions of the Yukon XL.
According to skgeinit.c of the sk98lin driver, "Flushing must be enabled
(needed for ASF see dev. #4.29), but the flushing mask should be
disabled (see dev. #4.115)". Nice. I implemented this same change in
the sky2 driver and verified that the RX lockup I was seeing was
resolved.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Prevent deadlock in sky2 recovery logic. sky2_down calls napi_synchronize
which gets stuck if napi was already disabled.
Fix by rearranging slightly and not calling napi_disable until after
both ports are stopped. The napi_disable probably is being overly
paranoid, but it is safe now.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add workaround for issues FE+ (A0) transmit watermark.
This is copied verbatim from vendor driver sk98lin (10.22.4.3).
Don't have that chip version and no more information seems to be available.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Using PCIE advanced error recovery stuff creates more user problems than it's worth.
The AER stuff depends on MMCONFIG and in many configurations it just doesn't work.
Plus it doesn't add any real functionality to the driver. The sky2
driver handles its own errors fine as is.
This reverts 555382cbfc
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Using the hardware window into PCI config space is more reliable
and smaller/faster than using the pci_config routines. It avoids issues
with MMCONFIG etc.
Reverts: 167f53d05f
Please apply for 2.6.24
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The Marvell Yukon XL chipset appears to have a hardware glitch
where it will repeat the checksum of the last packet. Of course, this is
timing sensitive and only happens sometimes...
More info: http://bugzilla.kernel.org/show_bug.cgi?id=9381
As a workaround just disable hardware checksumming by default on
this chip version. The earlier workaround for PCIX, dual port
was also on Yukon XL so don't need to disable checksumming there.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Found a couple of more chips in the latest version of the vendor driver.
They are minor variations on existing chips.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Netpoll will only work on port 0 because of the restrictive
relationship between NAPI and netpoll.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Stephen Hemminger
David S. Miller
Mike McCormack
Joe Perches
Stephen Hemminger
Ben Hutchings
Anton Vorontsov
Eric Dumazet
Yang Hongyang
Alexey Dobriyan
Johannes Berg
Rafael J. Wysocki
Huang Weiyi
Jeff Garzik
Stephen Hemminger