Mainly this is a preparation patch before adding one-by-one DMA SG entries
transmission. But logically the Tx and Rx DMA channels setup should be
performed in the dma_setup() callback anyway. So we'll move the DMA slave
channels src/dst burst lengths, address and address width configuration
from the Tx/Rx channels preparation methods to the dedicated functions and
then make sure it's called at the DMA setup stage.
Note we now make sure the return value of the dmaengine_slave_config()
method doesn't indicate an error. It has been unnecessary in case if Dw
DMAC is utilized as a DMA engine, since its device_config() callback
always returns zero (though it might change in future). But since DW APB
SSI driver now supports any DMA back-end we must make sure the DMA device
configuration has been successful before proceeding with further setups.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20200920112322.24585-4-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
Since commit 46164fde6b ("spi: dw: Fix Rx-only DMA transfers") if DMA
interface is enabled, then Tx-buffer must be available in each SPI
transfer. It's required since in order to activate the incoming data
reception either DMA or CPU must be pushing data out to the SPI bus.
But the DW APB SSI DMA driver code is still left in state as if Tx-buffer
might be optional, which is no longer true. Let's fix it so an error would
be returned if no Tx-buffer detected and DMA Tx would be always
enabled.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20200920112322.24585-3-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
Indeed the registers content doesn't get cleared when the SPI controller
is disabled and enabled. Max burst lengths aren't changed since the Rx and
Tx DMA channels are requested on init stage and are kept acquired until
the device is removed. Obviously SPI controller FIFO depth can't be
changed. Due to all of that we can safely move the DMA Transmit and
Receive data level registers initialization to the SPI controller DMA init
stage (when the SPI controller is being probed) instead of doing it for
each SPI transfer when dma_setup is called. This shall speed the DMA-based
SPI transfer initialization up a bit, particularly if the APB bus is
relatively slow.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20200920112322.24585-2-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
This series mainly add the IRQ mode support for hisi-sfc-v3xx driver, and some
cleanups for the preparation of the IRQ mode.
After this patch, the device can work in IRQ mode, or if firmware doesn't
declare irq support it will fall back to Poll mode.
Patch 1-2 refactor the .exec_op() path to make it simpler and clearer.
Patch 3 factor the definition of the interrupt bits.
Patch 4 add the IRQ support of the driver.
Yicong Yang (4):
spi: hisi-sfc-v3xx: factor out IO modes configuration
spi: hisi-sfc-v3xx: factor out bus config and transfer functions
spi: hisi-sfc-v3xx: factor out the bit definition of interrupt
register
spi: hisi-sfc-v3xx: add support for IRQ mode
drivers/spi/spi-hisi-sfc-v3xx.c | 261 +++++++++++++++++++++++++++++-----------
1 file changed, 190 insertions(+), 71 deletions(-)
--
2.8.1
______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/
CLK_TO_US macro is used to calculate potential transfer time for various
timeout handling. However it overflows on transfer bigger than 512 bytes
because it first did (len * 8 * 1000000).
This controller typically operates at 45MHz. This patch did 2 things:
1. calculate clock / 1000000 first
2. add a 4M transfer size cap so that the final timeout in DMA reading
doesn't overflow
Fixes: 881d1ee9fe ("spi: add support for mediatek spi-nor controller")
Cc: <stable@vger.kernel.org>
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Link: https://lore.kernel.org/r/20200922114905.2942859-1-gch981213@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The controller can work with interrupts, so add support for it.
Then we can work under IRQ mode or Poll mode now, if firmware
doesn't declare the IRQ support, it will fall back to Poll mode.
Acked-by: John Garry <john.garry@huawei.com>
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Link: https://lore.kernel.org/r/1600950270-52536-5-git-send-email-yangyicong@hisilicon.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The definition of the register field in the interrupt corresponding
registers are the same. So factor them out to public place.
Acked-by: John Garry <john.garry@huawei.com>
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Link: https://lore.kernel.org/r/1600950270-52536-4-git-send-email-yangyicong@hisilicon.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In hisi_sfc_v3xx_generic_exec_op(), we will write the data to the buffer,
configure and start the transfer, read the data to the buffer and check
whether occurs an error. Factor out the config and transfer start codes
as individual functions, to make the process a bit clearer.
Acked-by: John Garry <john.garry@huawei.com>
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Link: https://lore.kernel.org/r/1600950270-52536-3-git-send-email-yangyicong@hisilicon.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Factor IO modes configuration out of hisi_sfc_v3xx_generic_exec_op()
using an IO modes lookup table. This will make the process a bit clearer
and reduce the cyclomatic complexity. Simplify the IO mode definition
macros a little bit as well.
Also add the .supports_op() method for the controller mem ops, in order
to avoid OOB access.
Acked-by: John Garry <john.garry@huawei.com>
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Link: https://lore.kernel.org/r/1600950270-52536-2-git-send-email-yangyicong@hisilicon.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch implementes the reporting of the effectivly used speed_hz for the
transfer by setting tfr->effective_speed_hz.
See the following patch, which adds this feature to the SPI core for more
information:
5d7e2b5ed5 spi: core: allow reporting the effectivly used speed_hz for a transfer
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/r/20200917202420.1914104-1-mkl@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
This reverts commit 13d515c796 (spi: omap2-mcspi: Switch to
readl_poll_timeout()).
The amount of time spent polling for the MCSPI_CHSTAT bits to be set on
AM335x-icev2 platform is less than 1us (about 0.6us) in most cases, with
or without using DMA. So, in most cases the function need not sleep.
Also, setting the sleep_usecs to zero would not be optimal here because
ktime_add_us() used in readl_poll_timeout() is slower compared to the
direct addition used after the revert. So, it is sub-optimal to use
readl_poll_timeout in this case.
When DMA is not enabled, this revert results in an increase of about 27%
in throughput and decrease of about 20% in CPU usage. However, the CPU
usage and throughput are almost the same when used with DMA.
Therefore, fix this by reverting the commit which switched to using
readl_poll_timeout().
Fixes: 13d515c796 ("spi: omap2-mcspi: Switch to readl_poll_timeout()")
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Link: https://lore.kernel.org/r/20200910122624.8769-1-a-govindraju@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
sg_init_table zeroes its first argument, so the allocation of that argument
doesn't have to.
the semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression x,n,flags;
@@
x =
- kcalloc
+ kmalloc_array
(n,sizeof(*x),flags)
...
sg_init_table(x,n)
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Link: https://lore.kernel.org/r/1600601186-7420-12-git-send-email-Julia.Lawall@inria.fr
Signed-off-by: Mark Brown <broonie@kernel.org>
This series implements a number of fixes for the FSI-attached SPI
controller driver.
Changes since v1:
- Switch to a new compatible string for the restricted version of the
SPI controller, rather than a new boolean parameter.
Brad Bishop (3):
spi: fsi: Handle 9 to 15 byte transfers lengths
spi: fsi: Fix clock running too fast
spi: fsi: Fix use of the bneq+ sequencer instruction
Eddie James (3):
dt-bindings: fsi: fsi2spi: Add compatible string for restricted
version
spi: fsi: Implement restricted size for certain controllers
spi: fsi: Check mux status before transfers
.../devicetree/bindings/fsi/ibm,fsi2spi.yaml | 1 +
drivers/spi/spi-fsi.c | 139 ++++++++++++++----
2 files changed, 109 insertions(+), 31 deletions(-)
--
2.26.2
Free previously allocated IRQs when return an error code of desc->setup()
which is not always successful. And simplify the code by adding a goto
label.
Fixes: 8f5c285f3e ("SPI: designware: pci: Switch over to MSI interrupts")
CC: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Jay Fang <f.fangjian@huawei.com>
Link: https://lore.kernel.org/r/1600132969-53037-1-git-send-email-f.fangjian@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently NXP fspi driver has support of DT only. Adding ACPI
support to the driver so that it can be used by UEFI firmware
booting in ACPI mode. This driver will be probed if any firmware
will expose HID "NXP0009" in DSDT table.
Signed-off-by: kuldip dwivedi <kuldip.dwivedi@puresoftware.com>
Reviewed-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Link: https://lore.kernel.org/r/20200911130331.6313-1-kuldip.dwivedi@puresoftware.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The info message was showing the mapped address of the device. To avoid
security problems, all virtual addresses are converted to __ptrval__, so
the message was useless/ugly:
[ 2.304949] xilinx_spi b0010000.spi-flash: at 0xB0010000 mapped to 0x(____ptrval____), irq=37
Use %pR instead:
[ 15.021354] xilinx_spi b0010000.spi-flash: at [mem 0xb0010000-0xb001ffff], irq=37
Signed-off-by: Ricardo Ribalda <ribalda@kernel.org>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/20200915112936.320647-1-ribalda@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a compatible string for the restricted version of the SPI controller.
The restricted version cannot process sequence loop operations and
therefore has a smaller transfer size.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Link: https://lore.kernel.org/r/20200909222857.28653-5-eajames@linux.ibm.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The SPI controllers are not accessible if the mux isn't set. Therefore,
check the mux status before starting a transfer and fail out if it isn't
set.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20200909222857.28653-7-eajames@linux.ibm.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Some of the FSI-attached SPI controllers cannot use the loop command in
programming the sequencer due to security requirements. Check the
devicetree compatibility that indicates this condition and restrict the
size for these controllers. Also, add more transfers directly in the
sequence up to the length of the sequence register.
Fixes: bbb6b2f986 ("spi: Add FSI-attached SPI controller driver")
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20200909222857.28653-6-eajames@linux.ibm.com
Signed-off-by: Mark Brown <broonie@kernel.org>
All of the switches in N2_count_control in the counter configuration are
required to make the branch if not equal and increment command work.
Set them when using bneq+.
A side effect of this mode requires a dummy write to TDR when both
transmitting and receiving otherwise the controller won't start shifting
receive data.
It is likely not possible to avoid TDR underrun errors in this mode and
they are harmless, so do not check for them.
Fixes: bbb6b2f986 ("spi: Add FSI-attached SPI controller driver")
Signed-off-by: Brad Bishop <bradleyb@fuzziesquirrel.com>
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20200909222857.28653-4-eajames@linux.ibm.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use a clock divider tuned to a 200MHz FSI bus frequency (the maximum). Use
of the previous divider at 200MHz results in corrupt data from endpoint
devices. Ideally the clock divider would be calculated from the FSI clock,
but that would require some significant work on the FSI driver. With FSI
frequencies slower than 200MHz, the SPI clock will simply run slower, but
safely.
Signed-off-by: Brad Bishop <bradleyb@fuzziesquirrel.com>
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20200909222857.28653-3-eajames@linux.ibm.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The trailing <len> - 8 bytes of transfer data in this size range is no
longer ignored.
Fixes: bbb6b2f986 ("spi: Add FSI-attached SPI controller driver")
Signed-off-by: Brad Bishop <bradleyb@fuzziesquirrel.com>
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20200909222857.28653-2-eajames@linux.ibm.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and the error value gets printed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Chunyan Zhang <zhang.lyra@gmail.com>
Link: https://lore.kernel.org/r/20200910160706.5883-1-krzk@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
If we're sending bytes over SPI, we know the FIFO is empty at the
start of the transfer. There's no reason to wait for the interrupt
telling us to start--we can just start right away. Then if we
transmit everything in one swell foop we don't even need to bother
listening for TX interrupts.
In a test of "flashrom -p ec -r /tmp/foo.bin" interrupts were reduced
from ~30560 to ~29730, about a 3% savings.
This patch looks bigger than it is because I moved a few functions
rather than adding a forward declaration. The only actual change to
geni_spi_handle_tx() was to make it return a bool indicating if there
is more to tx.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Akash Asthana <akashast@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20200912111716.1.Ied5e843fad0d6b733a1fb8bcfb364dd2fa889eb3@changeid
Signed-off-by: Mark Brown <broonie@kernel.org>
This eliminates the following sparse warning:
drivers/spi/spi-bcm2835.c:78:14: warning: symbol 'polling_limit_us' was
not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Link: https://lore.kernel.org/r/20200912072211.602735-1-yanaijie@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The arch/arm64/boot/dts/freescale/fsl-ls208xa.dtsi device tree lacks DMA
channels for DSPI, so naturally, the driver fails to probe:
[ 2.945302] fsl-dspi 2100000.spi: rx dma channel not available
[ 2.951134] fsl-dspi 2100000.spi: can't get dma channels
In retrospect, this should have been obvious, because LS2080A, LS2085A
LS2088A and LX2160A don't appear to have an eDMA module at all. Looking
again at their datasheets, the CTARE register (which is specific to XSPI
functionality) seems to be documented, so switch them to XSPI mode
instead.
Fixes: 0feaf8f5af ("spi: spi-fsl-dspi: Convert the instantiations that support it to DMA")
Reported-by: Qiang Zhao <qiang.zhao@nxp.com>
Tested-by: Qiang Zhao <qiang.zhao@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20200910121532.1138596-1-olteanv@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
We always toggle the chip select manually in spi-geni-qcom so that we
can properly implement the Linux API. There's no reason to program
this to the hardware on every transfer. Program it once at init and
be done with it.
This saves some part of a microsecond of overhead on each transfer.
While not really noticeable on any real world benchmarks, we might as
well save the time.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20200912140730.2.I33e571179986850b4ec17042e813d0b08fb1b9c1@changeid
Signed-off-by: Mark Brown <broonie@kernel.org>
In commit 902481a78e ("spi: spi-geni-qcom: Actually use our FIFO") I
explained that the maximum size we could program the FIFO was
"mas->tx_fifo_depth - 3" but that I chose "mas->tx_fifo_depth()"
because I was worried about decreased bandwidth.
Since that time:
* All the interconnect patches have landed, making things run at the
proper speed.
* I've done more measurements.
This lets me confirm that there's really no downside of using the FIFO
more. Specifically I did "flashrom -p ec -r /tmp/foo.bin" on a
Chromebook and averaged over several runs.
Before: It took 6.66 seconds and 59669 interrupts fired.
After: It took 6.66 seconds and 47992 interrupts fired.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20200912140730.1.Ie67fa32009b94702d56232c064f1d89065ee8836@changeid
Signed-off-by: Mark Brown <broonie@kernel.org>
It is redundant to do irqsave and irqrestore in hardIRQ context.
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Barry Song <song.bao.hua@hisilicon.com>
Link: https://lore.kernel.org/r/20200910100246.32696-1-song.bao.hua@hisilicon.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The Broadcom QSPI driver now falls back to no MSPI_DEV support as the
default setting in the generic compatible string, explicit settings for
STB chips 7425, 7429, and 7435 can be removed.
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20200910152539.45584-4-ray.jui@broadcom.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add compatible string for BRCMSTB 7445 SoCs and indicate it has MSPI rev
support.
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20200910152539.45584-2-ray.jui@broadcom.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The variable ret is being initialized with a value that is
never read and it is being updated later with a new value. The
initialization is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20200910150410.750959-1-colin.king@canonical.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Hello,
This cleans up some of the user code around calls to
dev_pm_opp_of_remove_table().
All the patches can be picked by respective maintainers directly except
for the last patch, which needs the previous two to get merged first.
These are based for 5.9-rc1.
Rajendra, Since most of these changes are related to qcom stuff, it
would be great if you can give them a try. I wasn't able to test them
due to lack of hardware.
Ulf, I had to revise the sdhci patch, sorry about that. Please pick this
one.
Diff between V1 and V2 is mentioned in each of the patches separately.
Viresh Kumar (8):
cpufreq: imx6q: Unconditionally call dev_pm_opp_of_remove_table()
drm/lima: Unconditionally call dev_pm_opp_of_remove_table()
drm/msm: Unconditionally call dev_pm_opp_of_remove_table()
mmc: sdhci-msm: Unconditionally call dev_pm_opp_of_remove_table()
spi: spi-geni-qcom: Unconditionally call dev_pm_opp_of_remove_table()
spi: spi-qcom-qspi: Unconditionally call dev_pm_opp_of_remove_table()
tty: serial: qcom_geni_serial: Unconditionally call
dev_pm_opp_of_remove_table()
qcom-geni-se: remove has_opp_table
drivers/cpufreq/imx6q-cpufreq.c | 10 ++--------
drivers/gpu/drm/lima/lima_devfreq.c | 6 +-----
drivers/gpu/drm/lima/lima_devfreq.h | 1 -
drivers/gpu/drm/msm/disp/dpu1/dpu_kms.c | 14 +++++---------
drivers/gpu/drm/msm/disp/dpu1/dpu_kms.h | 1 -
drivers/gpu/drm/msm/dsi/dsi_host.c | 8 ++------
drivers/mmc/host/sdhci-msm.c | 14 +++++---------
drivers/spi/spi-geni-qcom.c | 13 +++++--------
drivers/spi/spi-qcom-qspi.c | 15 ++++++---------
drivers/tty/serial/qcom_geni_serial.c | 13 +++++--------
include/linux/qcom-geni-se.h | 2 --
11 files changed, 31 insertions(+), 66 deletions(-)
base-commit: f4d51dffc6
--
2.25.0.rc1.19.g042ed3e048af
In spidev_read() and spidev_write(), the variable status is being
initialized with a value that is never read and it is being updated
later with a new value. The initialization is redundant and can be
removed.
Signed-off-by: Jay Fang <f.fangjian@huawei.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/1599631704-53232-1-git-send-email-f.fangjian@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
dev_pm_opp_of_remove_table() doesn't report any errors when it fails to
find the OPP table with error -ENODEV (i.e. OPP table not present for
the device). And we can call dev_pm_opp_of_remove_table()
unconditionally here.
While at it, create a new label and put clkname on errors.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Link: https://lore.kernel.org/r/b77aa0bbe82a580508e321a34da488b4b27966d0.1598594714.git.viresh.kumar@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
dev_pm_opp_of_remove_table() doesn't report any errors when it fails to
find the OPP table with error -ENODEV (i.e. OPP table not present for
the device). And we can call dev_pm_opp_of_remove_table()
unconditionally here.
While at it, create a new label and put clkname on errors.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Link: https://lore.kernel.org/r/ea0864d41277e61fa31d304fbd4cf9af6b314269.1598594714.git.viresh.kumar@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The series add support for the Sparx5 SoC SPI controller in the
spi-dw-mmio.c spi driver.
v5 changes:
- rx-sample-delay-ns documentation changes from Rob Herring:
- Drop superfluous type $ref
- Add default value = 0
v4 changes:
- Changed snps,rx-sample-delay-ns to snps,rx-sample-delay-ns
suggested by Rob Herring (rockchip also has this property).
- Added support for controller-level rx-sample-delay-ns value as
well as per SPI slave value (rockchip has controller-level property).
- Dropped internal mux in favor of suggested spi-mux to
control bus inteface selection.
v3 changes:
- Added mux support for controlling SPI bus interface. This is new mux
driver, bindings and added to sparx5 base DT.
- Removed "microchip,spi-interface2" property in favour of
"mux-controls" property in SPI controller (sparx5 only).
- Changed dw_spi_sparx5_set_cs() to use the mux control instead of
directly acessing "mux" register. Associated code/defines moved to mux
driver.
- Changed dw_spi_sparx5_set_cs() to match other similar functions in
signature and avoid explicit CS toggling.
- Spun off duplicated NAND device DT chunks into separate DT file.
v2 changes:
- Moved all RX sample delay into spi-dw-core.c, using
the "snps,rx-sample-delay-ns" device property.
- Integrated Sparx5 support directly in spi-dw-mmio.c
- Changed SPI2 configuration to per-slave "microchip,spi-interface2"
property.
- Added bindings to existing snps,dw-apb-ssi.yaml file
- Dropped patches for polled mode and SPI memory operations.
Lars Povlsen (6):
spi: dw: Add support for RX sample delay register
spi: dw: Add Microchip Sparx5 support
arm64: dts: sparx5: Add SPI controller and associated mmio-mux
dt-bindings: snps,dw-apb-ssi: Add sparx5 support, plus
rx-sample-delay-ns property
arm64: dts: sparx5: Add spi-nor support
arm64: dts: sparx5: Add spi-nand devices
.../bindings/spi/snps,dw-apb-ssi.yaml | 21 ++++++
arch/arm64/boot/dts/microchip/sparx5.dtsi | 47 ++++++++++++-
.../arm64/boot/dts/microchip/sparx5_nand.dtsi | 31 ++++++++
.../boot/dts/microchip/sparx5_pcb125.dts | 30 ++++++++
.../boot/dts/microchip/sparx5_pcb134.dts | 1 +
.../dts/microchip/sparx5_pcb134_board.dtsi | 16 +++++
.../boot/dts/microchip/sparx5_pcb135.dts | 1 +
.../dts/microchip/sparx5_pcb135_board.dtsi | 16 +++++
drivers/spi/spi-dw-core.c | 26 +++++++
drivers/spi/spi-dw-mmio.c | 70 ++++++++++++++++++-
drivers/spi/spi-dw.h | 3 +
11 files changed, 260 insertions(+), 2 deletions(-)
create mode 100644 arch/arm64/boot/dts/microchip/sparx5_nand.dtsi
--
2.27.0
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.orghttp://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Use default supports_op() to support spi-[rt]x-bus-width properties.
And check dummy op's byte length instead of its bus width for output.
Signed-off-by: Ikjoon Jang <ikjn@chromium.org>
Link: https://lore.kernel.org/r/20200826091852.519138-1-ikjn@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and the error value gets printed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200901152713.18629-11-krzk@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and the error value gets printed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200901152713.18629-10-krzk@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and the error value gets printed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200901152713.18629-9-krzk@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and the error value gets printed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200901152713.18629-8-krzk@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>