This breaks the build as this header is not meant to be used in this
way.
./include/linux/unaligned/access_ok.h:8:28: error: redefinition of ‘get_unaligned_le16’
static __always_inline u16 get_unaligned_le16(const void *p)
^~~~~~~~~~~~~~~~~~
In file included from drivers/bluetooth/hci_nokia.c:32:
./include/linux/unaligned/le_struct.h:7:19: note: previous definition of ‘get_unaligned_le16’ was here
static inline u16 get_unaligned_le16(const void *p)
Use asm/unaligned.h instead.
Signed-off-by: David S. Miller <davem@davemloft.net>
ATM accounts for in-flight TX packets in sk_wmem_alloc of the VCC on
which they are to be sent. But it doesn't take ownership of those
packets from the sock (if any) which originally owned them. They should
remain owned by their actual sender until they've left the box.
There's a hack in pskb_expand_head() to avoid adjusting skb->truesize
for certain skbs, precisely to avoid messing up sk_wmem_alloc
accounting. Ideally that hack would cover the ATM use case too, but it
doesn't — skbs which aren't owned by any sock, for example PPP control
frames, still get their truesize adjusted when the low-level ATM driver
adds headroom.
This has always been an issue, it seems. The truesize of a packet
increases, and sk_wmem_alloc on the VCC goes negative. But this wasn't
for normal traffic, only for control frames. So I think we just got away
with it, and we probably needed to send 2GiB of LCP echo frames before
the misaccounting would ever have caused a problem and caused
atm_may_send() to start refusing packets.
Commit 14afee4b60 ("net: convert sock.sk_wmem_alloc from atomic_t to
refcount_t") did exactly what it was intended to do, and turned this
mostly-theoretical problem into a real one, causing PPPoATM to fail
immediately as sk_wmem_alloc underflows and atm_may_send() *immediately*
starts refusing to allow new packets.
The least intrusive solution to this problem is to stash the value of
skb->truesize that was accounted to the VCC, in a new member of the
ATM_SKB(skb) structure. Then in atm_pop_raw() subtract precisely that
value instead of the then-current value of skb->truesize.
Fixes: 158f323b98 ("net: adjust skb->truesize in pskb_expand_head()")
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Tested-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf 2018-06-16
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Fix a panic in devmap handling in generic XDP where return type
of __devmap_lookup_elem() got changed recently but generic XDP
code missed the related update, from Toshiaki.
2) Fix a freeze when BPF progs are loaded that include BPF to BPF
calls when JIT is enabled where we would later bail out via error
path w/o dropping kallsyms, and another one to silence syzkaller
splats from locking prog read-only, from Daniel.
3) Fix a bug in test_offloads.py BPF selftest which must not assume
that the underlying system have no BPF progs loaded prior to test,
and one in bpftool to fix accuracy of program load time, from Jakub.
4) Fix a bug in bpftool's probe for availability of the bpf(2)
BPF_TASK_FD_QUERY subcommand, from Yonghong.
5) Fix a regression in AF_XDP's XDP_SKB receive path where queue
id check got erroneously removed, from Björn.
6) Fix missing state cleanup in BPF's xfrm tunnel test, from William.
7) Check tunnel type more accurately in BPF's tunnel collect metadata
kselftest, from Jian.
8) Fix missing Kconfig fragments for BPF kselftests, from Anders.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull AFS updates from Al Viro:
"Assorted AFS stuff - ended up in vfs.git since most of that consists
of David's AFS-related followups to Christoph's procfs series"
* 'afs-proc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
afs: Optimise callback breaking by not repeating volume lookup
afs: Display manually added cells in dynamic root mount
afs: Enable IPv6 DNS lookups
afs: Show all of a server's addresses in /proc/fs/afs/servers
afs: Handle CONFIG_PROC_FS=n
proc: Make inline name size calculation automatic
afs: Implement network namespacing
afs: Mark afs_net::ws_cell as __rcu and set using rcu functions
afs: Fix a Sparse warning in xdr_decode_AFSFetchStatus()
proc: Add a way to make network proc files writable
afs: Rearrange fs/afs/proc.c to remove remaining predeclarations.
afs: Rearrange fs/afs/proc.c to move the show routines up
afs: Rearrange fs/afs/proc.c by moving fops and open functions down
afs: Move /proc management functions to the end of the file
Pull compat updates from Al Viro:
"Some biarch patches - getting rid of assorted (mis)uses of
compat_alloc_user_space().
Not much in that area this cycle..."
* 'work.compat' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
orangefs: simplify compat ioctl handling
signalfd: lift sigmask copyin and size checks to callers of do_signalfd4()
vmsplice(): lift importing iovec into vmsplice(2) and compat counterpart
Pull aio fixes from Al Viro:
"Assorted AIO followups and fixes"
* 'work.aio' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
eventpoll: switch to ->poll_mask
aio: only return events requested in poll_mask() for IOCB_CMD_POLL
eventfd: only return events requested in poll_mask()
aio: mark __aio_sigset::sigmask const
Pull networking fixes from David Miller:
1) Various netfilter fixlets from Pablo and the netfilter team.
2) Fix regression in IPVS caused by lack of PMTU exceptions on local
routes in ipv6, from Julian Anastasov.
3) Check pskb_trim_rcsum for failure in DSA, from Zhouyang Jia.
4) Don't crash on poll in TLS, from Daniel Borkmann.
5) Revert SO_REUSE{ADDR,PORT} change, it regresses various things
including Avahi mDNS. From Bart Van Assche.
6) Missing of_node_put in qcom/emac driver, from Yue Haibing.
7) We lack checking of the TCP checking in one special case during SYN
receive, from Frank van der Linden.
8) Fix module init error paths of mac80211 hwsim, from Johannes Berg.
9) Handle 802.1ad properly in stmmac driver, from Elad Nachman.
10) Must grab HW caps before doing quirk checks in stmmac driver, from
Jose Abreu.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (81 commits)
net: stmmac: Run HWIF Quirks after getting HW caps
neighbour: skip NTF_EXT_LEARNED entries during forced gc
net: cxgb3: add error handling for sysfs_create_group
tls: fix waitall behavior in tls_sw_recvmsg
tls: fix use-after-free in tls_push_record
l2tp: filter out non-PPP sessions in pppol2tp_tunnel_ioctl()
l2tp: reject creation of non-PPP sessions on L2TPv2 tunnels
mlxsw: spectrum_switchdev: Fix port_vlan refcounting
mlxsw: spectrum_router: Align with new route replace logic
mlxsw: spectrum_router: Allow appending to dev-only routes
ipv6: Only emit append events for appended routes
stmmac: added support for 802.1ad vlan stripping
cfg80211: fix rcu in cfg80211_unregister_wdev
mac80211: Move up init of TXQs
mac80211_hwsim: fix module init error paths
cfg80211: initialize sinfo in cfg80211_get_station
nl80211: fix some kernel doc tag mistakes
hv_netvsc: Fix the variable sizes in ipsecv2 and rsc offload
rds: avoid unenecessary cong_update in loop transport
l2tp: clean up stale tunnel or session in pppol2tp_connect's error path
...
Summary of modules changes for the 4.18 merge window:
- Minor code cleanup and also allow sig_enforce param to be shown in
sysfs with CONFIG_MODULE_SIG_FORCE
Signed-off-by: Jessica Yu <jeyu@kernel.org>
-----BEGIN PGP SIGNATURE-----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=5gpe
-----END PGP SIGNATURE-----
Merge tag 'modules-for-v4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/jeyu/linux
Pull module updates from Jessica Yu:
"Minor code cleanup and also allow sig_enforce param to be shown in
sysfs with CONFIG_MODULE_SIG_FORCE"
* tag 'modules-for-v4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/jeyu/linux:
module: Allow to always show the status of modsign
module: Do not access sig_enforce directly
Pull uml updates from Richard Weinberger:
"Minor updates for UML:
- fixes for our new vector network driver by Anton
- initcall cleanup by Alexander
- We have a new mailinglist, sourceforge.net sucks"
* 'for-linus-4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/uml:
um: Fix raw interface options
um: Fix initialization of vector queues
um: remove uml initcalls
um: Update mailing list address
Commit 67f29e07e1 ("bpf: devmap introduce dev_map_enqueue") changed
the return value type of __devmap_lookup_elem() from struct net_device *
to struct bpf_dtab_netdev * but forgot to modify generic XDP code
accordingly.
Thus generic XDP incorrectly used struct bpf_dtab_netdev where struct
net_device is expected, then skb->dev was set to invalid value.
v2:
- Fix compiler warning without CONFIG_BPF_SYSCALL.
Fixes: 67f29e07e1 ("bpf: devmap introduce dev_map_enqueue")
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Acked-by: Yonghong Song <yhs@fb.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
This tag contains some small RISC-V updates I'd like to target for 4.18.
They are all fairly small this time. Here's a short summary, there's
more info in the commits/merges.
* A fix to __clear_user to respect the passed arguments.
* Enough support for the perf subsystem to work with RISC-V's ISA
defined performance counters.
* Support for sparse and cleanups suggested by it.
* Support for R_RISCV_32 (a relocation, not the 32-bit ISA).
* Some MAINTAINERS cleanups.
* The addition of CONFIG_HVC_RISCV_SBI to our defconfig, as it's always
present.
I've given these a simple build+boot test.
-----BEGIN PGP SIGNATURE-----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=D+sb
-----END PGP SIGNATURE-----
Merge tag 'riscv-for-linus-4.18-merge_window' of git://git.kernel.org/pub/scm/linux/kernel/git/palmer/riscv-linux
Pull RISC-V updates from Palmer Dabbelt:
"This contains some small RISC-V updates I'd like to target for 4.18.
They are all fairly small this time. Here's a short summary, there's
more info in the commits/merges:
- a fix to __clear_user to respect the passed arguments.
- enough support for the perf subsystem to work with RISC-V's ISA
defined performance counters.
- support for sparse and cleanups suggested by it.
- support for R_RISCV_32 (a relocation, not the 32-bit ISA).
- some MAINTAINERS cleanups.
- the addition of CONFIG_HVC_RISCV_SBI to our defconfig, as it's
always present.
I've given these a simple build+boot test"
* tag 'riscv-for-linus-4.18-merge_window' of git://git.kernel.org/pub/scm/linux/kernel/git/palmer/riscv-linux:
RISC-V: Add CONFIG_HVC_RISCV_SBI=y to defconfig
RISC-V: Handle R_RISCV_32 in modules
riscv/ftrace: Export _mcount when DYNAMIC_FTRACE isn't set
riscv: add riscv-specific predefines to CHECKFLAGS
riscv: split the declaration of __copy_user
riscv: no __user for probe_kernel_address()
riscv: use NULL instead of a plain 0
perf: riscv: Add Document for Future Porting Guide
perf: riscv: preliminary RISC-V support
MAINTAINERS: Update Albert's email, he's back at Berkeley
MAINTAINERS: Add myself as a maintainer for SiFive's drivers
riscv: Fix the bug in memory access fixup code
for the hyperv config issue and a typo fix.
Main PPC changes: reimplement the MMIO instruction emulation,
transactional memory support for PR KVM, improve radix page table
handling.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJbIp2DAAoJEL/70l94x66DdZwH/jAI259VXA3VJJZ21mMLry4m
8uL28N/zYgiokPnzE9/BoP3o48ksYGdrJcvIUgHScTNHrMdMGTv/wkvExEzQ+j9Z
orCVF46zyGFA1KevEaEfTCrTsUO2HX7kCeZou7J8F37YdxgEqEOIoa6ozC+XVrB5
q75KnnIqizM5Hi5+kdCEPiBZ1Qzy+F8kXtg4OqXSEOubiyxXvTmkC65sUBrEzleW
uGHB4qNJ0bpLZAeKrrh2yDwhqR3Dw3Mqz97mA4CygfWm1BjQsPpO8u80NtXr2gW5
iB3hB7RvzlRpzVHxaKAiKu+DAQWkhiEGPAolWGuQ5mFm1V31qw7UO/TDylKSXZk=
=keBY
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull more kvm updates from Paolo Bonzini:
"Mostly the PPC part of the release, but also switching to Arnd's fix
for the hyperv config issue and a typo fix.
Main PPC changes:
- reimplement the MMIO instruction emulation
- transactional memory support for PR KVM
- improve radix page table handling"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (63 commits)
KVM: x86: VMX: redo fix for link error without CONFIG_HYPERV
KVM: x86: fix typo at kvm_arch_hardware_setup comment
KVM: PPC: Book3S PR: Fix failure status setting in tabort. emulation
KVM: PPC: Book3S PR: Enable use on POWER9 bare-metal hosts in HPT mode
KVM: PPC: Book3S PR: Don't let PAPR guest set MSR hypervisor bit
KVM: PPC: Book3S PR: Fix failure status setting in treclaim. emulation
KVM: PPC: Book3S PR: Fix MSR setting when delivering interrupts
KVM: PPC: Book3S PR: Handle additional interrupt types
KVM: PPC: Book3S PR: Enable kvmppc_get/set_one_reg_pr() for HTM registers
KVM: PPC: Book3S: Remove load/put vcpu for KVM_GET_REGS/KVM_SET_REGS
KVM: PPC: Remove load/put vcpu for KVM_GET/SET_ONE_REG ioctl
KVM: PPC: Move vcpu_load/vcpu_put down to each ioctl case in kvm_arch_vcpu_ioctl
KVM: PPC: Book3S PR: Enable HTM for PR KVM for KVM_CHECK_EXTENSION ioctl
KVM: PPC: Book3S PR: Support TAR handling for PR KVM HTM
KVM: PPC: Book3S PR: Add guard code to prevent returning to guest with PR=0 and Transactional state
KVM: PPC: Book3S PR: Add emulation for tabort. in privileged state
KVM: PPC: Book3S PR: Add emulation for trechkpt.
KVM: PPC: Book3S PR: Add emulation for treclaim.
KVM: PPC: Book3S PR: Restore NV regs after emulating mfspr from TM SPRs
KVM: PPC: Book3S PR: Always fail transactions in guest privileged state
...
VF support for virtio.
DMA barriers for virtio strong barriers.
Bugfixes.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJbHykhAAoJECgfDbjSjVRpTAgH/iS2bIo0DOvlC5wPljVMopKV
fD3n5dPUDOc2yWv2H9wwc3xDO6f3kByMjLnHvn+PM2ZX/ms731QaPd5sTlzUm+jj
LzvI0gc9cyym8INZcU+xuTLQhiC13wZmZIHuP7X4TRsKBPTSaT+goSRk63qmuJF7
0V8BJcj2QXaygaWD1P5SczrL4nFK7nn5PWZqZTPk3ohuLcUtgcv6Qb+idj+tCnov
6osK122JkN6GO/LuVgEPxKamDgi9SB+sXeqNCYSzgKzXEUyC/cMtxyExXKxwqDEI
MCcfPcoS1IklvII0ZYCTFKJYDTkPCjZ3HQwxF9aVjy4FirJGpRI3NRp5Eqr9rG4=
=+EYn
-----END PGP SIGNATURE-----
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull virtio updates from Michael Tsirkin:
"virtio, vhost: features, fixes
- PCI virtual function support for virtio
- DMA barriers for virtio strong barriers
- bugfixes"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
virtio: update the comments for transport features
virtio_pci: support enabling VFs
vhost: fix info leak due to uninitialized memory
virtio_ring: switch to dma_XX barriers for rpmsg
Daniel Borkmann says:
====================
First one is a panic I ran into while testing the second
one where we got several syzkaller reports. Series here
fixes both.
Thanks!
====================
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
We currently lock any JITed image as read-only via bpf_jit_binary_lock_ro()
as well as the BPF image as read-only through bpf_prog_lock_ro(). In
the case any of these would fail we throw a WARN_ON_ONCE() in order to
yell loudly to the log. Perhaps, to some extend, this may be comparable
to an allocation where __GFP_NOWARN is explicitly not set.
Added via 65869a47f3 ("bpf: improve read-only handling"), this behavior
is slightly different compared to any of the other in-kernel set_memory_ro()
users who do not check the return code of set_memory_ro() and friends /at
all/ (e.g. in the case of module_enable_ro() / module_disable_ro()). Given
in BPF this is mandatory hardening step, we want to know whether there
are any issues that would leave both BPF data writable. So it happens
that syzkaller enabled fault injection and it triggered memory allocation
failure deep inside x86's change_page_attr_set_clr() which was triggered
from set_memory_ro().
Now, there are two options: i) leaving everything as is, and ii) reworking
the image locking code in order to have a final checkpoint out of the
central bpf_prog_select_runtime() which probes whether any of the calls
during prog setup weren't successful, and then bailing out with an error.
Option ii) is a better approach since this additional paranoia avoids
altogether leaving any potential W+X pages from BPF side in the system.
Therefore, lets be strict about it, and reject programs in such unlikely
occasion. While testing I noticed also that one bpf_prog_lock_ro()
call was missing on the outer dummy prog in case of calls, e.g. in the
destructor we call bpf_prog_free_deferred() on the main prog where we
try to bpf_prog_unlock_free() the program, and since we go via
bpf_prog_select_runtime() do that as well.
Reported-by: syzbot+3b889862e65a98317058@syzkaller.appspotmail.com
Reported-by: syzbot+9e762b52dd17e616a7a5@syzkaller.appspotmail.com
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
While testing I found that when hitting error path in bpf_prog_load()
where we jump to free_used_maps and prog contained BPF to BPF calls
that were JITed earlier, then we never clean up the bpf_prog_kallsyms_add()
done under jit_subprogs(). Add proper API to make BPF kallsyms deletion
more clear and fix that.
Fixes: 1c2a088a66 ("bpf: x64: add JIT support for multi-function programs")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Currently we were running HWIF quirks before getting HW capabilities.
This is not right because some HWIF callbacks depend on HW caps.
Lets save the quirks callback and use it in a later stage.
This fixes Altera socfpga.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Fixes: 5f0456b431 ("net: stmmac: Implement logic to automatically select HW Interface")
Reported-by: Dinh Nguyen <dinh.linux@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Vitor Soares <soares@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Dinh Nguyen <dinh.linux@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 9ce33e4653 ("neighbour: support for NTF_EXT_LEARNED flag")
added support for NTF_EXT_LEARNED for neighbour entries.
NTF_EXT_LEARNED entries are neigh entries managed by control
plane (eg: Ethernet VPN implementation in FRR routing suite).
Periodic gc already excludes these entries. This patch extends
it to forced gc which the earlier patch missed.
Fixes: 9ce33e4653 ("neighbour: support for NTF_EXT_LEARNED flag")
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When sysfs_create_group fails, the lack of error-handling code may
cause unexpected results.
This patch adds error-handling code after calling sysfs_create_group.
Signed-off-by: Zhouyang Jia <jiazhouyang09@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
Two tls fixes
First one is syzkaller trigered uaf and second one noticed
while writing test code with tls ulp. For details please see
individual patches.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Current behavior in tls_sw_recvmsg() is to wait for incoming tls
messages and copy up to exactly len bytes of data that the user
provided. This is problematic in the sense that i) if no packet
is currently queued in strparser we keep waiting until one has been
processed and pushed into tls receive layer for tls_wait_data() to
wake up and push the decrypted bits to user space. Given after
tls decryption, we're back at streaming data, use sock_rcvlowat()
hint from tcp socket instead. Retain current behavior with MSG_WAITALL
flag and otherwise use the hint target for breaking the loop and
returning to application. This is done if currently no ctx->recv_pkt
is ready, otherwise continue to process it from our strparser
backlog.
Fixes: c46234ebb4 ("tls: RX path for ktls")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Dave Watson <davejwatson@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
syzkaller managed to trigger a use-after-free in tls like the
following:
BUG: KASAN: use-after-free in tls_push_record.constprop.15+0x6a2/0x810 [tls]
Write of size 1 at addr ffff88037aa08000 by task a.out/2317
CPU: 3 PID: 2317 Comm: a.out Not tainted 4.17.0+ #144
Hardware name: LENOVO 20FBCTO1WW/20FBCTO1WW, BIOS N1FET47W (1.21 ) 11/28/2016
Call Trace:
dump_stack+0x71/0xab
print_address_description+0x6a/0x280
kasan_report+0x258/0x380
? tls_push_record.constprop.15+0x6a2/0x810 [tls]
tls_push_record.constprop.15+0x6a2/0x810 [tls]
tls_sw_push_pending_record+0x2e/0x40 [tls]
tls_sk_proto_close+0x3fe/0x710 [tls]
? tcp_check_oom+0x4c0/0x4c0
? tls_write_space+0x260/0x260 [tls]
? kmem_cache_free+0x88/0x1f0
inet_release+0xd6/0x1b0
__sock_release+0xc0/0x240
sock_close+0x11/0x20
__fput+0x22d/0x660
task_work_run+0x114/0x1a0
do_exit+0x71a/0x2780
? mm_update_next_owner+0x650/0x650
? handle_mm_fault+0x2f5/0x5f0
? __do_page_fault+0x44f/0xa50
? mm_fault_error+0x2d0/0x2d0
do_group_exit+0xde/0x300
__x64_sys_exit_group+0x3a/0x50
do_syscall_64+0x9a/0x300
? page_fault+0x8/0x30
entry_SYSCALL_64_after_hwframe+0x44/0xa9
This happened through fault injection where aead_req allocation in
tls_do_encryption() eventually failed and we returned -ENOMEM from
the function. Turns out that the use-after-free is triggered from
tls_sw_sendmsg() in the second tls_push_record(). The error then
triggers a jump to waiting for memory in sk_stream_wait_memory()
resp. returning immediately in case of MSG_DONTWAIT. What follows is
the trim_both_sgl(sk, orig_size), which drops elements from the sg
list added via tls_sw_sendmsg(). Now the use-after-free gets triggered
when the socket is being closed, where tls_sk_proto_close() callback
is invoked. The tls_complete_pending_work() will figure that there's
a pending closed tls record to be flushed and thus calls into the
tls_push_pending_closed_record() from there. ctx->push_pending_record()
is called from the latter, which is the tls_sw_push_pending_record()
from sw path. This again calls into tls_push_record(). And here the
tls_fill_prepend() will panic since the buffer address has been freed
earlier via trim_both_sgl(). One way to fix it is to move the aead
request allocation out of tls_do_encryption() early into tls_push_record().
This means we don't prep the tls header and advance state to the
TLS_PENDING_CLOSED_RECORD before allocation which could potentially
fail happened. That fixes the issue on my side.
Fixes: 3c4d755915 ("tls: kernel TLS support")
Reported-by: syzbot+5c74af81c547738e1684@syzkaller.appspotmail.com
Reported-by: syzbot+709f2810a6a05f11d4d3@syzkaller.appspotmail.com
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Dave Watson <davejwatson@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Guillaume Nault says:
====================
l2tp: l2tp_ppp must ignore non-PPP sessions
The original L2TP code was written for version 2 of the protocol, which
could only carry PPP sessions. Then L2TPv3 generalised the protocol so that
it could transport different kinds of pseudo-wires. But parts of the
l2tp_ppp module still break in presence of non-PPP sessions.
Assuming L2TPv2 tunnels can only transport PPP sessions is right, but
l2tp_netlink failed to ensure that (fixed in patch 1).
When retrieving a session from an arbitrary tunnel, l2tp_ppp needs to
filter out non-PPP sessions (last occurrence fixed in patch 2).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
pppol2tp_tunnel_ioctl() can act on an L2TPv3 tunnel, in which case
'session' may be an Ethernet pseudo-wire.
However, pppol2tp_session_ioctl() expects a PPP pseudo-wire, as it
assumes l2tp_session_priv() points to a pppol2tp_session structure. For
an Ethernet pseudo-wire l2tp_session_priv() points to an l2tp_eth_sess
structure instead, making pppol2tp_session_ioctl() access invalid
memory.
Fixes: d9e31d17ce ("l2tp: Add L2TP ethernet pseudowire support")
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
The /proc/net/pppol2tp handlers (pppol2tp_seq_*()) iterate over all
L2TPv2 tunnels, and rightfully expect that only PPP sessions can be
found there. However, l2tp_netlink accepts creating Ethernet sessions
regardless of the underlying tunnel version.
This confuses pppol2tp_seq_session_show(), which expects that
l2tp_session_priv() returns a pppol2tp_session structure. When the
session is an Ethernet pseudo-wire, a struct l2tp_eth_sess is returned
instead. This leads to invalid memory access when
pppol2tp_session_get_sock() later tries to dereference ps->sk.
Fixes: d9e31d17ce ("l2tp: Add L2TP ethernet pseudowire support")
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel says:
====================
mlxsw: IPv6 and reference counting fixes
The first three patches fix a mismatch between the new IPv6 behavior
introduced in commit f34436a430 ("net/ipv6: Simplify route replace and
appending into multipath route") and mlxsw. The patches allow the driver
to support multipathing in IPv6 overlays with GRE tunnel devices. A
selftest will be submitted when net-next opens.
The last patch fixes a reference count problem of the port_vlan struct.
I plan to simplify the code in net-next, so that reference counting is
not necessary anymore.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Switchdev notifications for addition of SWITCHDEV_OBJ_ID_PORT_VLAN are
distributed not only on clean addition, but also when flags on an
existing VLAN are changed. mlxsw_sp_bridge_port_vlan_add() calls
mlxsw_sp_port_vlan_get() to get at the port_vlan in question, which
implicitly references the object. This then leads to discrepancies in
reference counting when the VLAN is removed. spectrum.c warns about the
problem when the module is removed:
[13578.493090] WARNING: CPU: 0 PID: 2454 at drivers/net/ethernet/mellanox/mlxsw/spectrum.c:2973 mlxsw_sp_port_remove+0xfd/0x110 [mlxsw_spectrum]
[...]
[13578.627106] Call Trace:
[13578.629617] mlxsw_sp_fini+0x2a/0xe0 [mlxsw_spectrum]
[13578.634748] mlxsw_core_bus_device_unregister+0x3e/0x130 [mlxsw_core]
[13578.641290] mlxsw_pci_remove+0x13/0x40 [mlxsw_pci]
[13578.646238] pci_device_remove+0x31/0xb0
[13578.650244] device_release_driver_internal+0x14f/0x220
[13578.655562] driver_detach+0x32/0x70
[13578.659183] bus_remove_driver+0x47/0xa0
[13578.663134] pci_unregister_driver+0x1e/0x80
[13578.667486] mlxsw_sp_module_exit+0xc/0x3fa [mlxsw_spectrum]
[13578.673207] __x64_sys_delete_module+0x13b/0x1e0
[13578.677888] ? exit_to_usermode_loop+0x78/0x80
[13578.682374] do_syscall_64+0x39/0xe0
[13578.685976] entry_SYSCALL_64_after_hwframe+0x44/0xa9
Fix by putting the port_vlan when mlxsw_sp_port_vlan_bridge_join()
determines it's a flag-only change.
Fixes: b3529af6bb ("spectrum: Reference count VLAN entries")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit f34436a430 ("net/ipv6: Simplify route replace and appending
into multipath route") changed the IPv6 route replace logic so that the
first matching route (i.e., same metric) is replaced.
Have mlxsw replace the first matching route as well.
Fixes: f34436a430 ("net/ipv6: Simplify route replace and appending into multipath route")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit f34436a430 ("net/ipv6: Simplify route replace and appending
into multipath route") changed the IPv6 route append logic so that
dev-only routes can be appended and not only gatewayed routes.
Align mlxsw with the new behaviour.
Fixes: f34436a430 ("net/ipv6: Simplify route replace and appending into multipath route")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current code will emit an append event in the FIB notification chain for
any route added with NLM_F_APPEND set, even if the route was not
appended to any existing route.
This is inconsistent with IPv4 where such an event is only emitted when
the new route is appended after an existing one.
Align IPv6 behavior with IPv4, thereby allowing listeners to more easily
handle these events.
Fixes: f34436a430 ("net/ipv6: Simplify route replace and appending into multipath route")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* missing RCU grace period enforcement led to drivers freeing
data structures before; fix from Dedy Lansky.
* hwsim module init error paths were messed up; fixed it myself
after a report from Colin King (who had sent a partial patch)
* kernel-doc tag errors; fix from Luca Coelho
* initialize the on-stack sinfo data structure when getting
station information; fix from Sven Eckelmann
* TXQ state dumping is now done from init, and when TXQs aren't
initialized yet at that point, bad things happen, move the
initialization; fix from Toke Høiland-Jørgensen.
-----BEGIN PGP SIGNATURE-----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=siAL
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-davem-2018-06-15' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
A handful of fixes:
* missing RCU grace period enforcement led to drivers freeing
data structures before; fix from Dedy Lansky.
* hwsim module init error paths were messed up; fixed it myself
after a report from Colin King (who had sent a partial patch)
* kernel-doc tag errors; fix from Luca Coelho
* initialize the on-stack sinfo data structure when getting
station information; fix from Sven Eckelmann
* TXQ state dumping is now done from init, and when TXQs aren't
initialized yet at that point, bad things happen, move the
initialization; fix from Toke Høiland-Jørgensen.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
stmmac reception handler calls stmmac_rx_vlan() to strip the vlan before
calling napi_gro_receive().
The function assumes VLAN tagged frames are always tagged with
802.1Q protocol, and assigns ETH_P_8021Q to the skb by hard-coding
the parameter on call to __vlan_hwaccel_put_tag() .
This causes packets not to be passed to the VLAN slave if it was created
with 802.1AD protocol
(ip link add link eth0 eth0.100 type vlan proto 802.1ad id 100).
This fix passes the protocol from the VLAN header into
__vlan_hwaccel_put_tag() instead of using the hard-coded value of
ETH_P_8021Q.
NETIF_F_HW_VLAN_STAG_RX check was added and the strip action is now
dependent on the correct combination of features and the detected vlan tag.
NETIF_F_HW_VLAN_STAG_RX feature was added to be in line with the driver
actual abilities.
Signed-off-by: Elad Nachman <eladn@gilat.com>
Reviewed-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
At the moment, afs_break_callbacks calls afs_break_one_callback() for each
separate FID it was given, and the latter looks up the volume individually
for each one.
However, this is inefficient if two or more FIDs have the same vid as we
could reuse the volume. This is complicated by cell aliasing whereby we
may have multiple cells sharing a volume and can therefore have multiple
callback interests for any particular volume ID.
At the moment afs_break_one_callback() scans the entire list of volumes
we're getting from a server and breaks the appropriate callback in every
matching volume, regardless of cell. This scan is done for every FID.
Optimise callback breaking by the following means:
(1) Sort the FID list by vid so that all FIDs belonging to the same volume
are clumped together.
This is done through the use of an indirection table as we cannot do
an insertion sort on the afs_callback_break array as we decode FIDs
into it as we subsequently also have to decode callback info into it
that corresponds by array index only.
We also don't really want to bubblesort afterwards if we can avoid it.
(2) Sort the server->cb_interests array by vid so that all the matching
volumes are grouped together. This permits the scan to stop after
finding a record that has a higher vid.
(3) When breaking FIDs, we try to keep server->cb_break_lock as long as
possible, caching the start point in the array for that volume group
as long as possible.
It might make sense to add another layer in that list and have a
refcounted volume ID anchor that has the matching interests attached
to it rather than being in the list. This would allow the lock to be
dropped without losing the cursor.
Signed-off-by: David Howells <dhowells@redhat.com>
Alter the dynroot mount so that cells created by manipulation of
/proc/fs/afs/cells and /proc/fs/afs/rootcell and by specification of a root
cell as a module parameter will cause directories for those cells to be
created in the dynamic root superblock for the network namespace[*].
To this end:
(1) Only one dynamic root superblock is now created per network namespace
and this is shared between all attempts to mount it. This makes it
easier to find the superblock to modify.
(2) When a dynamic root superblock is created, the list of cells is walked
and directories created for each cell already defined.
(3) When a new cell is added, if a dynamic root superblock exists, a
directory is created for it.
(4) When a cell is destroyed, the directory is removed.
(5) These directories are created by calling lookup_one_len() on the root
dir which automatically creates them if they don't exist.
[*] Inasmuch as network namespaces are currently supported here.
Signed-off-by: David Howells <dhowells@redhat.com>
Callers of cfg80211_unregister_wdev can free the wdev object
immediately after this function returns. This may crash the kernel
because this wdev object is still in use by other threads.
Add synchronize_rcu() after list_del_rcu to make sure wdev object can
be safely freed.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
On init, ieee80211_if_add() dumps the interface. Since that now includes a
dump of the TXQ state, we need to initialise that before the dump happens.
So move up the TXQ initialisation to to before the call to
ieee80211_if_add().
Fixes: 52539ca89f ("cfg80211: Expose TXQ stats and parameters to userspace")
Reported-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
Tested-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
We didn't free the workqueue on any errors, nor did we
correctly check for rhashtable allocation errors, nor
did we free the hashtable on error.
Reported-by: Colin King <colin.king@canonical.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Most of the implementations behind cfg80211_get_station will not initialize
sinfo to zero before manipulating it. For example, the member "filled",
which indicates the filled in parts of this struct, is often only modified
by enabling certain bits in the bitfield while keeping the remaining bits
in their original state. A caller without a preinitialized sinfo.filled can
then no longer decide which parts of sinfo were filled in by
cfg80211_get_station (or actually the underlying implementations).
cfg80211_get_station must therefore take care that sinfo is initialized to
zero. Otherwise, the caller may tries to read information which was not
filled in and which must therefore also be considered uninitialized. In
batadv_v_elp_get_throughput's case, an invalid "random" expected throughput
may be stored for this neighbor and thus the B.A.T.M.A.N V algorithm may
switch to non-optimal neighbors for certain destinations.
Fixes: 7406353d43 ("cfg80211: implement cfg80211_get_station cfg80211 API")
Reported-by: Thomas Lauer <holminateur@gmail.com>
Reported-by: Marcel Schmidt <ff.z-casparistrasse@mailbox.org>
Cc: b.a.t.m.a.n@lists.open-mesh.org
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
There is a bunch of tags marking constants with &, which means struct
or enum name. Replace them with %, which is the correct tag for
constants.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
This second Kselftest update for Linux 4.18-rc1:
- fixes a signedness bug in cgroups test
- adds ppc support for kprobe args tests
-----BEGIN PGP SIGNATURE-----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=5i77
-----END PGP SIGNATURE-----
Merge tag 'linux-kselftest-4.18-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull more Kselftest updates from Shuah Khan:
- fix a signedness bug in cgroups test
- add ppc support for kprobe args tests
* tag 'linux-kselftest-4.18-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
kselftest/cgroup: fix a signedness bug
selftests/ftrace: Add ppc support for kprobe args tests
Here is a collection of small fixes on top of the previous update.
All small and obvious fixes. Mostly for usual suspects, USB-audio and
HD-audio, but a few trivial error handling fixes for misc drivers as
well.
-----BEGIN PGP SIGNATURE-----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=XDCD
-----END PGP SIGNATURE-----
Merge tag 'sound-fix-4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Here is a collection of small fixes on top of the previous update.
All small and obvious fixes. Mostly for usual suspects, USB-audio and
HD-audio, but a few trivial error handling fixes for misc drivers as
well"
* tag 'sound-fix-4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: usb-audio: Always create the interrupt pipe for the mixer
ALSA: usb-audio: Add insertion control for UAC3 BADD
ALSA: usb-audio: Change in connectors control creation interface
ALSA: usb-audio: Add bi-directional terminal types
ALSA: lx6464es: add error handling for pci_ioremap_bar
ALSA: sonicvibes: add error handling for snd_ctl_add
ALSA: usb-audio: Remove explicitly listed Mytek devices
ALSA: usb-audio: Generic DSD detection for XMOS-based implementations
ALSA: usb-audio: Add native DSD support for Mytek DACs
ALSA: hda/realtek - Add shutup hint
ALSA: usb-audio: Disable the quirk for Nura headset
ALSA: hda: add dock and led support for HP ProBook 640 G4
ALSA: hda: add dock and led support for HP EliteBook 830 G5
ALSA: emu10k1: add error handling for snd_ctl_add
ALSA: fm801: add error handling for snd_ctl_add
-----BEGIN PGP SIGNATURE-----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=YBRl
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2018-06-15' of git://anongit.freedesktop.org/drm/drm
Pull amd drm fixes from Dave Airlie:
"Just a single set of AMD fixes for stuff in -next for -rc1"
* tag 'drm-next-2018-06-15' of git://anongit.freedesktop.org/drm/drm: (47 commits)
drm/amd/powerplay: Set higher SCLK&MCLK frequency than dpm7 in OD (v2)
drm/amd/powerplay: remove uncessary extra gfxoff control call
drm/amdgpu: fix parsing indirect register list v2
drm/amd/include: Update df 3.6 mask and shift definition
drm/amd/pp: Fix OD feature enable failed on Vega10 workstation cards
drm/amd/display: Fix stale buffer object (bo) use
drm/amd/pp: initialize result to before or'ing in data
drm/amd/powerplay: fix wrong clock adjust sequence
drm/amdgpu: Grab/put runtime PM references in atomic_commit_tail()
drm/amd/powerplay: fix missed hwmgr check warning before call gfx_off_control handler
drm/amdgpu: fix CG enabling hang with gfxoff enabled
drm/amdgpu: fix clear_all and replace handling in the VM (v2)
drm/amdgpu: add checking for sos version
drm/amdgpu: fix the missed vcn fw version report
Revert "drm/amdgpu: Add an ATPX quirk for hybrid laptop"
drm/amdgpu/df: fix potential array out-of-bounds read
drm/amdgpu: Fix NULL pointer when load kfd driver with PP block is disabled
drm/gfx9: Update gc goldensetting for vega20.
drm/amd/pp: Allow underclocking when od table is empty in vbios
drm/amdgpu/display: check if ppfuncs exists before using it
...
Show all of a server's addresses in /proc/fs/afs/servers, placing the
second plus addresses on padded lines of their own. The current address is
marked with a star.
Signed-off-by: David Howells <dhowells@redhat.com>
The AFS filesystem depends at the moment on /proc for configuration and
also presents information that way - however, this causes a compilation
failure if procfs is disabled.
Fix it so that the procfs bits aren't compiled in if procfs is disabled.
This means that you can't configure the AFS filesystem directly, but it is
still usable provided that an up-to-date keyutils is installed to look up
cells by SRV or AFSDB DNS records.
Reported-by: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: David Howells <dhowells@redhat.com>
Make calculation of the size of the inline name in struct proc_dir_entry
automatic, rather than having to manually encode the numbers and failing to
allow for lockdep.
Require a minimum inline name size of 33+1 to allow for names that look
like two hex numbers with a dash between.
Reported-by: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
These fields in struct ndis_ipsecv2_offload and struct ndis_rsc_offload
are one byte according to the specs. This patch defines them with the
right size. These structs are not in use right now, but will be used soon.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Loop transport which is self loopback, remote port congestion
update isn't relevant. Infact the xmit path already ignores it.
Receive path needs to do the same.
Reported-by: syzbot+4c20b3866171ce8441d2@syzkaller.appspotmail.com
Reviewed-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>