These are various power management related changes, mainly concerning
cpuidle on i.MX and OMAP, as well as a the move of the omap smartreflex
driver to live in the power subsystem.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=tgT5
-----END PGP SIGNATURE-----
Merge tag 'pm' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc power management changes from Arnd Bergmann:
"These are various power management related changes, mainly concerning
cpuidle on i.MX and OMAP, as well as a the move of the omap
smartreflex driver to live in the power subsystem."
Fix up conflicts in arch/arm/mach-{imx/mach-imx6q.c,omap2/prm2xxx_3xxx.h}
* tag 'pm' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (37 commits)
ARM: OMAP2+: PM: fix IRQ_NOAUTOEN removal by mis-merge
ARM: OMAP2+: do not allow SmartReflex to be built as a module
ARM: OMAP2: Use hwmod to initialize mmc for 2420
ARM: OMAP3: PM: cpuidle: optimize the clkdm idle latency in C1 state
ARM: OMAP3: PM: cpuidle: optimize the PER latency in C1 state
ARM: OMAP3: PM: cpuidle: default to C1 in next_valid_state
ARM: OMAP3: PM: cleanup cam_pwrdm leftovers
ARM: OMAP3: PM: call pre/post transition per powerdomain
ARM: OMAP2+: powerdomain: allow pre/post transtion to be per pwrdm
ARM: OMAP3: PM: Remove IO Daisychain control from cpuidle
ARM: OMAP3PLUS: hwmod: reconfigure IO Daisychain during hwmod mux
ARM: OMAP3+: PRM: Enable IO wake up
ARM: OMAP4: PRM: Add IO Daisychain support
ARM: OMAP3: PM: Move IO Daisychain function to omap3 prm file
ARM: OMAP3: PM: correct enable/disable of daisy io chain
ARM: OMAP2+: PRM: fix compile for OMAP4-only build
W1: OMAP HDQ1W: use runtime PM
ARM: OMAP2+: HDQ1W: use omap_device
W1: OMAP HDQ1W: use 32-bit register accesses
W1: OMAP HDQ1W: allow driver to be built on all OMAP2+
...
This contains two branches dealing with timers, one for the picoxcell
platform that is now using DT with the platform-independent
dw_apb_timer driver. The other change is for the omap-specific
dmtimer driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=2bZ2
-----END PGP SIGNATURE-----
Merge tag 'timer' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc timer updates from Arnd Bergmann:
"This contains two branches dealing with timers, one for the picoxcell
platform that is now using DT with the platform-independent
dw_apb_timer driver. The other change is for the omap-specific
dmtimer driver."
* tag 'timer' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
clocksource: dw_apb_timer: Add common DTS glue for dw_apb_timer
ARM: OMAP2+: Simplify dmtimer clock aliases
ARM: OMAP2+: Move dmtimer clock set function to dmtimer driver
ARM: OMAP1: Fix dmtimer support
ARM: OMAP: Add flag to indicate if a timer needs a manual reset
ARM: OMAP: Remove timer function pointer for context loss counter
ARM: OMAP: Remove loses_context variable from timer platform data
ARM: OMAP2+: Fix external clock support for dmtimers
ARM: OMAP2+: HWMOD: Correct timer device attributes
ARM: OMAP: Add DMTIMER capability variable to represent timer features
ARM: OMAP2+: Add dmtimer platform function to reserve systimers
ARM: OMAP2+: Remove unused max number of timers definition
ARM: OMAP: Remove unnecessary clk structure
These are all boring changes, moving stuff around or renaming things
mostly, and also getting rid of stuff that is duplicate or should
not be there to start with. Platform-wise this is all over the place,
mainly omap, samsung, at91, imx and tegra.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=4zvd
-----END PGP SIGNATURE-----
Merge tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull general arm-soc cleanups from Arnd Bergmann:
"These are all boring changes, moving stuff around or renaming things
mostly, and also getting rid of stuff that is duplicate or should not
be there to start with. Platform-wise this is all over the place,
mainly omap, samsung, at91, imx and tegra."
Resolve trivial conflict in arch/arm/mach-omap2/clockdomains3xxx_data.c
* tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (67 commits)
ARM: clps711x: Remove the setting of the time
ARM: clps711x: Removed superfluous transform virt_to_bus and related functions
ARM: clps711x/p720t: Replace __initcall by .init_early call
ARM: S3C24XX: Remove unused GPIO definitions for Openmoko GTA02 board
ARM: S3C24XX: Remove unused GPIO definitions for port J
ARM: S3C24XX: Remove unused GPA, GPE, GPH bank GPIO aliases
ARM: S3C24XX: Convert the touchscreen setup code to common GPIO API
ARM: S3C24XX: Convert the PM code to gpiolib API
ARM: S3C24XX: Convert QT2410 board file to the gpiolib API
ARM: S3C24XX: Convert SMDK board file to the gpiolib API
ARM: S3C24XX: Free the backlight gpio requested in Mini2440 board code
ARM: imx: remove unused pdata from device macros
ARM: imx: Kconfig: Remove IMX_HAVE_PLATFORM_IMX_SSI from MACH_MX25_3DS
ARM: at91: fix new build errors
ARM: at91: add AIC5 support
ARM: at91: remove mach/irqs.h
ARM: at91: sparse irq support
ARM: at91: at91 based machines specify their own irq handler at run time
ARM: at91: remove static irq priorities for sam9x5
ARM: at91: add of irq priorities support
...
Add hwmod support for the EMAC (and MDIO)
ethernet controller that's on the am35x
family of SoC's.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
[paul@pwsan.com: updated subject line; updated to apply on v3.5-rc4;
added comments to hwmod data regarding IPSS]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
During kernel init, the AM3505/AM3517 UART4 cannot complete its softreset:
omap_hwmod: uart4: softreset failed (waited 10000 usec)
This also results in another warning later in the boot process:
omap_hwmod: uart4: enabled state can only be entered from initialized, idle, or disabled state
From empirical observation, the AM35xx UART4 IP block requires either
uart1_fck or uart2_fck to be enabled while UART4 resets. Otherwise
the reset will never complete. So this patch adds uart1_fck as an
optional clock for UART4 and adds the appropriate hwmod flag to cause
uart1_fck to be enabled during the reset process. (The choice of
uart1_fck over uart2_fck was arbitrary.)
Unfortunately this observation raises many questions. Is it necessary
for uart1_fck or uart2_fck to be controlled with uart4_fck for the
UART4 to work correctly? What exactly do the AM35xx UART4 clock
tree and the related PRCM idle management FSMs look like? If anyone
has the ability to answer these questions through empirical functional
testing, or hardware information from the AM35xx designers, it would
be greatly appreciated.
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Kyle Manna <kyle.manna@fuel7.com>
Cc: Mark A. Greer <mgreer@animalcreek.com>
Cc: Ranjith Lohithakshan <ranjithl@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Mark A. Greer <mgreer@animalcreek.com>
Add missing terminators to the arrays of IRQ, DMA, and address space
structure records in the AM35xx UART4 hwmod data. Without these
terminators, the following warnings appear on boot:
omap_uart.3: failed to claim resource 58
omap_device: omap_uart: build failed (-16)
WARNING: at /home/paul/linux/arch/arm/mach-omap2/serial.c:375 omap_serial_init_port+0x198/0x284()
Could not build omap_device for omap_uart: uart4.
Also, AM35xx uart4_fck has an incorrect parent clock pointer. Fix it
and clean up a whitespace issue.
Fix some incorrectly-named macros related to AM35xx UART4.
Cc: Kyle Manna <kyle.manna@fuel7.com>
Cc: Mark A. Greer <mgreer@animalcreek.com>
Cc: Ranjith Lohithakshan <ranjithl@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Mark A. Greer <mgreer@animalcreek.com>
Partially fix the hwmod data for the AM35xx USB OTG hwmod. This
should resolve the following boot warning on AM35xx platforms:
omap_hwmod: am35x_otg_hs: cannot be enabled for reset (3)
While here, also fix the clkdev records, to avoid warnings about
duplicate clock aliases.
The hwmod is also connected to the wrong interconnect. It should be
connected to the IPSS, not the L4 CORE. But that is left for a future
fix, since it probably has a dependency on some hwmod core changes.
Cc: Felipe Balbi <balbi@ti.com>
Cc: Hema HK <hemahk@ti.com>
Cc: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Mark A. Greer <mgreer@animalcreek.com>
Remove the existing alias for pad_fck, prcm_fck from the clock data and
add them as opt_clks to the hwmod data.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The enable/disable module functions are specific to SoCs with
OMAP4-class PRCM. Rather than use cpu_is* checks at runtime inside
the enable/disable module functions, use cpu_is at init time to
initialize function pointers only for SoCs that need them.
NOTE: the cpu_is* check for _enable_module was different than
the one for _disable_module, and this patch uses
cpu_is_omap44xx() for both.
Signed-off-by: Kevin Hilman <khilman@ti.com>
[paul@pwsan.com: moved soc_ops function pointers to be per-kernel rather than
per-hwmod since they do not vary by hwmod; added kerneldoc]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Currently, the dmtimer determines whether an timer can support an external
clock source (sys_altclk) for driving the timer by the IP version. Only
OMAP24xx devices can support an external clock source, but the IP version
between OMAP24xx and OMAP3xxx is common and so this incorrectly indicates
that OMAP3 devices can use an external clock source.
Rather than use the IP version, just let the clock framework handle this.
If the "alt_ck" does not exist for a timer then the clock framework will fail
to find the clock and hence will return an error. By doing this we can eliminate
the "timer_ip_version" variable passed as part of the platform data and simplify
the code.
We can also remove the timer IP version from the HWMOD data because the dmtimer
driver uses the TIDR register to determine the IP version.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix the following issues with the timer device attributes for OMAP2+ devices:
1. For OMAP24xx devices, timers 2-8 have the ALWAYS-ON attribute indicating
that these timers are in an ALWAYS-ON power domain. This is not the case
only timer1 is in an ALWAYS-ON power domain.
2. For OMAP3xxx devices, timers 2-7 have the ALWAYS-ON attribute indicating
that these timers are in an ALWAYS-ON power domain. This is not the case
only timer1 and timer12 are in an ALWAYS-ON power domain.
3. For OMAP3xxx devices, timer12 does not have the ALWAYS-ON attribute but
is in an always-on power domain.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Change the name field value to better reflect the smartreflex
integration in the system.
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: J Keerthy <j-keerthy@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Move the smartreflex header file
(arch/arm/mach-omap2/smartreflex.h) in a new header file
include/linux/power/smartreflex.h.
This change makes the SmartReflex implementation ready for the move
to drivers/.
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: J Keerthy <j-keerthy@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
except for the RNG driver that will be done later on.
As this depends on omap-devel-hwmod-data-for-v3.5 and causes merge
conflict with omap-fixes-non-critical-for-v3.5, this branch is based
on merge of the two.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=w67p
-----END PGP SIGNATURE-----
Merge tag 'omap-cleanup-devices-for-v3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/cleanup2
Changes to split plat-omap/devices.c into mach-omap1 and mach-omap2
except for the RNG driver that will be done later on.
As this depends on omap-devel-hwmod-data-for-v3.5 and causes merge
conflict with omap-fixes-non-critical-for-v3.5, this branch is based
on merge of the two.
By Tony Lindgren (7) and others
via Tony Lindgren (4) and Paul Walmsley (1)
* tag 'omap-cleanup-devices-for-v3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (27 commits)
ARM: OMAP1: Pass dma request lines in platform data to MMC driver
ARM: OMAP: Move omap_mmc_add() to mach-omap1
ARM: OMAP2: Use hwmod to initialize mmc for 2420
ARM: OMAP2+: Move omap_dsp_reserve_sdram_memblock() to mach-omap2
ARM: OMAP1: Move omap_init_uwire to mach-omap1
ARM: OMAP1: Move omap_init_audio() to keep the devices in alphabetical order
ARM: OMAP2+: WDTIMER integration: fix !PM boot crash, disarm timer after hwmod reset
ARM: OMAP2/3: hwmod data: Add 32k-sync timer data to hwmod database
ARM: OMAP4: hwmod_data: Name the common irq for McBSP ports
ARM: OMAP4: hwmod data: I2C: add flag for context restore
ARM: OMAP3: hwmod_data: Rename the common irq for McBSP ports
ARM: OMAP2xxx: hwmod data: add HDQ/1-wire hwmod
ARM: OMAP3: hwmod data: add HDQ/1-wire hwmod
ARM: OMAP2+: hwmod data: add HDQ/1-wire hwmod shared data
ARM: OMAP2+: HDQ1W: add custom reset function
ARM: OMAP2420: hwmod data: Add MMC hwmod data for 2420
arm: omap3: clockdomain data: Remove superfluous commas from gfx_sgx_3xxx_wkdeps[]
ARM: OMAP2+: powerdomain: Get rid off duplicate pwrdm_clkdm_state_switch() API
ARM: OMAP3: clock data: add clockdomain for HDQ functional clock
ARM: OMAP3+: dpll: Configure autoidle mode only if it's supported
...
Currently cpu_is_omap3517() actually detects any device in the AM35x
family (3517 and no-SGX version 3505.) To make it more clear what is
being detected, convert the names from 3517 to AM35xx.
This adds a new soc_is_am35xx() which duplicates the cpu_is_omap3517().
In order to avoid cross-tree dependencies with clock-tree changes,
cpu_is_omap3517() is left until the clock changes are merged,
at which point cpu_is_omap3517() will be completely removed.
Acked-by: Vaibhav Hiremath <hvaibhav@ti.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>
Tested-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
[tony@atomide.com: change to use soc_is_omap instead]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Without runtime PM enabled, hwmod needs to leave all IP blocks in an
enabled state by default so any driver access to the HW will succeed.
This is accomplished by seting the postsetup_state to enabled for all
hwmods during init when runtime PM is disabled.
Currently, we have a special case for WDT in that its postsetup_state
is always set to disabled. This is done so that the WDT is disabled
and the timer is disarmed at boot in case there is no WDT driver.
This also means that when runtime PM is disabled, if a WDT driver *is*
built in the kernel, the kernel will crash on the first access to the
WDT hardware.
We can't simply leave the WDT module enabled, because the timer is
armed by default after reset. That means that if there is no WDT
driver initialzed or loaded before the timer expires, the kernel will
reboot.
To fix this, a custom reset method is added to the watchdog class of
omap_hwmod. This method will *always* disarm the timer after hwmod
reset. The WDT timer then will only be rearmed when/if the driver is
loaded for the WDT. With the timer disarmed by default, we no longer
need a special-case for the postsetup_state of WDT during init, so it
is removed.
Any platforms wishing to ensure the watchdog remains armed across the
entire boot boot can simply disable the reset-on-init feature of the
watchdog hwmod using omap_hwmod_no_setup_reset().
Tested on 3530/Overo, 4430/Panda.
NOTE: on 4430, the hwmod OCP reset does not seem to rearm the timer as
documented in the TRM (and what happens on OMAP3.) I noticed this
because testing the HWMOD_INIT_NO_RESET feature with no driver loaded,
I expected a reboot part way through the boot, but did not see a
reboot. Adding some debug to read the counter, I verified that right
after OCP softreset, the counter is not firing. After writing the
magic start sequence, the timer starts counting. This means that the
timer disarm sequence added here does not seem to be needed for 4430,
but is technically the correct way to ensure the timer is disarmed, so
it is left in for OMAP4.
Special thanks to Paul Walmsley for helping brainstorm ideas to fix
this problem.
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
[paul@pwsan.com: updated the omap2_wd_timer_reset() function in the
wake of commit 3c55c1baff ("ARM:
OMAP2+: hwmod: Revert "ARM: OMAP2+: hwmod: Make omap_hwmod_softreset
wait for reset status""); added kerneldoc; rolled in warning fix from Kevin]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Use 'common' as name for the common irq number in hwmod data for the McBSP
ports. The same name already in use for OMAP2430, and the OMAP4 hwmod data
will be using the same name.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add the HDQ1W hwmod for OMAP34xx, OMAP36xx, and AM3505/3517 devices.
According to the respective TRMs, it doesn't appear to be available for the
816x/814x or the AM335x.
The OCPIF_SWSUP_IDLE flag is added to work around an apparent hardware
bug: the hardware is not taking the CM_FCLKEN*_CORE.EN_HDQ bit into
account when considering whether to go idle:
http://www.spinics.net/lists/linux-omap/msg63576.html
This causes HDQ transfers to fail or become corrupt. Thanks to
NeilBrown for his help diagnosing and testing fixes for this problem.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: NeilBrown <neilb@suse.de>
Tested-by: NeilBrown <neilb@suse.de>
The IVA hwmod data is missing some fields that cause the following
warning on boot:
[ 0.118011] omap_hwmod: iva: cannot be enabled for reset (3)
Fix by encoding the IP block's main functional clock, reset lines, and
clockdomain.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The OMAP3 hwmod data listed iva2_ck as an interface clock between the
IVA and L3. This is incorrect. iva2_ck is not an interface clock.
Since it cannot auto-idle, specifying it here prevents the IVA and at
least one of the CORE clockdomains from going idle, which causes PM
problems such as these upon system suspend:
[ 70.626129] Powerdomain (iva2_pwrdm) didn't enter target state 1
[ 70.626190] Powerdomain (core_pwrdm) didn't enter target state 1
Fix by specifying the actual interface clock in the hwmod data.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Reorganize the hwmod data to declare the IP blocks first and the
interconnects second. This allows us to remove the forward
declarations, which this patch also does. Saves some lines of source
data. While here, take the opportunity to synchronize the order of
the OMAP44xx hwmod data with the autogenerator output -- it's slightly
different due to past mismerges -- and fix a few minor typos and
whitespace problems in the files.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Register interconnect links between IP blocks, rather than the IP
blocks themselves. (The IP blocks will be registered as a side-effect
of registering the links.)
The objective is to reduce the number of lines of static data and
facilitate the sharing of IP block data between different SoCs. These
objectives come at the penalty of increased boot time due to increased
computation.
While here, fix a few whitespace problems and inaccurate variable names.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
GPTIMER12 is attached to the L4 SEC interconnect, not directly to L4 WKUP.
Add the L4 SEC interconnect and attach GPTIMER12 to it.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The OMAP3 hwmod data was missing a DSS->L3 interconnect link for the
OMAP3430 ES1 DSS hwmod. Since the hwmod code and data is being modified
to register interfaces rather than hwmods, this would result in the DSS hwmod
not being registered correctly on OMAP3430ES1.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Commit a52e2ab66d ("ARM: OMAP3: hwmod
data: disable multiblock reads on MMC1/2 on OMAP34xx/35xx <= ES2.1")
didn't link the MMC hwmods to the interconnects correctly. Future
patches will register hwmods by interface, so if this is not fixed,
the MMC IP blocks won't be registered. Update the interface data
records to point to the correct IP blocks.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Some of the 2xxx and 3xxx hwmod data files use the old naming style
for hwmods, ending in a "_hwmod". These names are used by the OMAP
integration code to map hwmods to platform_devices, so they need to be
consistent, or the platform_devices won't be created. Remove the
_hwmod suffix to conform with the rest of the OMAP SoC data.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The clocks for all DSS slave interfaces were recently changed to "dss_ick" on
OMAP2 and OMAP3, this clock can be autoidled by PRCM. The VENC interface
previously had "dss_54m_fck" as it's clock which couldn't be autoidled, and
hence the OCPIF_SWSUP_IDLE flag was needed.
Remove the OCPIF_SWSUP_IDLE flag from VENC interfaces as it's clock is
now "dss_ick". This allows the PRCM hardware to autoidle the VENC
interface clocks when they are not active, rather than relying on the
software to do it, which can keep the interface clocks active
unnecessarily.
Signed-off-by: Archit Taneja <archit@ti.com>
[paul@pwsan.com: add a short description of the fix to the commit log]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add OMAP3 SmartReflex IRQs in hwmod structures. Without these IRQs
being registered the SmartReflex driver will be unable to get the
IRQ numbers to handle notifications.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
To set sr ntarget values for all volt_domain,
volt_table is retrieved by doing a look_up of 'vdd_name'
field from omap_hwmod but voltage domain pointer does not
belong to omap_hwmod and is not used anywhere else.
As a part of voltage layer and SR Layer clean up volt
pointer is removed from omap_hwmod and added in dev
attributes of SR. The value of the field must match
the voltage domain names for the binding to be effective.
Tested on OMAP3630 SDP, OMAP3530 Beagleboard and
OMAP4430 SDP Board.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Shweta Gulati <shweta.gulati@ti.com>
Acked by: Nishanth Menon <nm@ti.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
dss_core has to be initialized before any other DSS hwmod. Currently
this is broken as dss_core is listed in chip/revision specific hwmod
lists while other DSS hwmods are listed in common list which is
registered first.
This patch moves DSS hwmods (except for dss_core) to the separate list
which is registered last to ensure that dss_core is already registered.
This solves the problem with BUG() in L3 interrupt handler on boards
with DSS enabled in bootloader.
The long-term fix to this is to ensure modules are set up in dependency
order in the hwmod core code.
CC: Tomi Valkeinen <tomi.valkeinen@ti.com>
CC: Archit Taneja <archit@ti.com>
CC: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
[paul@pwsan.com: add notes that this is just a temporary workaround until
hwmod dependencies are added]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
dispc's sysc_flags is missing SYSC_HAS_ENAWAKEUP flag. This seems to
cause SYNC_LOST errors from the DSS when the power management is
enabled.
This patch adds the missing SYSC_HAS_ENAWAKEUP flag. Note that there are
other flags missing also (clock activity, DSI's sysc flags), but as they
are not critical, they will be fixed in the next merge window.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Currently OMAP2 and 3 share the same omap_hwmod_class and
omap_hwmod_class_sysconfig for dispc. However, OMAP3 has sysconfig
bits that OMAP2 doesn't have, so we need to split those structs into
OMAP2 and OMAP3 specific versions.
This patch only splits the structs, without changing the contents.
This is a prerequisite for a subsequent fix.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
[paul@pwsan.com: added commit note]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
For I2C clockactivity field is added for OMAP3 and OMAP4 that defines how the
interface (OCP) and functional (system) clocks behave when the I2C module is
idle.
The configuration of the clock activity bit field (per TRM) is as follows:
0x0: Both clocks can be cut off
0x1: Only OCP clock must be kept active; system clock
can be cut off
0x3: Both clocks must be kept active
0x2: Only system clock must be kept active; OCP clock
can be cut off
The patch makes 0x2(CLOCKACT_TEST_ICLK) the default for OMAP3 and OMAP4.
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The HSMMC1/HSMMC2 host controllers on OMAP34xx and
OMAP3503/3515/3525/3530 chips at ES levels prior to 3.0 can't do multiple
block reads[1]. Mark the hwmod data appropriately.
Reported by Dave Hylands <dhylands@gmail.com> and Steve Sakoman
<sakoman@gmail.com>. Thanks to Steve Sakoman for further help
testing this patch.
1. See for example Advisory 2.1.1.128 "MMC: Multiple Block Read
Operation Issue" in _OMAP3530/3525/3515/3503 Silicon Errata_
Revision F (October 2010) (SPRZ278F), available from
http://focus.ti.com/lit/er/sprz278f/sprz278f.pdf
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Dave Hylands <dhylands@gmail.com>
Cc: Steve Sakoman <sakoman@gmail.com>
Following 2 hwmod structures are added
1. usb_host_hs
The hwmod of usbhs with uhh, ehci and ohci base addresses
functional clock and ehci, ohci irqs
2. usb_tll_hs
hwmod of usbhs with the TLL base address and irq.
Signed-off-by: Keshava Munegowda <keshava_mgowda@ti.com>
Reviewed-by: Partha Basak <parthab@india.ti.com>
[paul@pwsan.com: fixed whitespace; removed nonexistent TLL->L3 interface;
added master & slave for L4 CORE->TLL interface; skip registration on
3430ES1; fixed multiline comment style; updated to apply on Tony's cleanup
branch; rebased]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add hwmod support to enable access to UART4 of the AM35xx series of
chips. The UART4 device referenced from the TRM will show up as ttyO3.
This was tested on an AM3505.
Signed-off-by: Kyle Manna <kyle.manna@fuel7.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Seems the commit 7e89098 was overly aggressive in adding iva and mailbox
hwmods so now they are registered twice.
------------[ cut here ]------------
WARNING: at arch/arm/mach-omap2/omap_hwmod.c:1959 omap_hwmod_register+0x104/0x12c()
omap_hwmod: iva: _register returned -22
Modules linked in:
[<c0012aa4>] (unwind_backtrace+0x0/0xec) from [<c002f970>] (warn_slowpath_common+0x4c/0x64)
[<c002f970>] (warn_slowpath_common+0x4c/0x64) from [<c002fa08>] (warn_slowpath_fmt+0x2c/0x3c)
[<c002fa08>] (warn_slowpath_fmt+0x2c/0x3c) from [<c02fdb4c>] (omap_hwmod_register+0x104/0x12c)
[<c02fdb4c>] (omap_hwmod_register+0x104/0x12c) from [<c02fbb44>] (omap3_init_early+0x1c/0x28)
[<c02fbb44>] (omap3_init_early+0x1c/0x28) from [<c02f9580>] (setup_arch+0x6b8/0x7a4)
[<c02f9580>] (setup_arch+0x6b8/0x7a4) from [<c02f754c>] (start_kernel+0x6c/0x264)
[<c02f754c>] (start_kernel+0x6c/0x264) from [<80008040>] (0x80008040)
---[ end trace 1b75b31a2719ed1c ]---
------------[ cut here ]------------
WARNING: at arch/arm/mach-omap2/omap_hwmod.c:1959 omap_hwmod_register+0x104/0x12c()
omap_hwmod: mailbox: _register returned -22
Modules linked in:
[<c0012aa4>] (unwind_backtrace+0x0/0xec) from [<c002f970>] (warn_slowpath_common+0x4c/0x64)
[<c002f970>] (warn_slowpath_common+0x4c/0x64) from [<c002fa08>] (warn_slowpath_fmt+0x2c/0x3c)
[<c002fa08>] (warn_slowpath_fmt+0x2c/0x3c) from [<c02fdb4c>] (omap_hwmod_register+0x104/0x12c)
[<c02fdb4c>] (omap_hwmod_register+0x104/0x12c) from [<c02fbb44>] (omap3_init_early+0x1c/0x28)
[<c02fbb44>] (omap3_init_early+0x1c/0x28) from [<c02f9580>] (setup_arch+0x6b8/0x7a4)
[<c02f9580>] (setup_arch+0x6b8/0x7a4) from [<c02f754c>] (start_kernel+0x6c/0x264)
[<c02f754c>] (start_kernel+0x6c/0x264) from [<80008040>] (0x80008040)
---[ end trace 1b75b31a2719ed1d ]---
Signed-off-by: Felipe Contreras <felipe.contreras@gmail.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Resetting DISPC when a DISPC output is enabled causes the DSS to go into an
inconsistent state. Thus if the bootloader has enabled a display, the hwmod code
cannot reset the DISPC module just like that, but the outputs need to be
disabled first.
Add function dispc_disable_outputs() which disables all active overlay manager
and ensure all frame transfers are completed.
Modify omap_dss_reset() to call this function and clear DSS_CONTROL,
DSS_SDI_CONTROL and DSS_PLL_CONTROL so that DSS is in a clean state when the
DSS2 driver starts.
This resolves the hang issue(caused by a L3 error during boot) seen on the
beagle board C3, which has a factory bootloader that enables display. The issue
is resolved with this patch.
Thanks to Tomi and Sricharan for some additional testing.
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: R, Sricharan <r.sricharan@ti.com>
Signed-off-by: Archit Taneja <archit@ti.com>
[paul@pwsan.com: restructured code, removed omap_{read,write}l(), removed
cpu_is_omap*() calls and converted to dev_attr]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The OMAP3 HWMOD data currently contains these errors with DSS clocks:
- dss_rfbi is missing ick opt-clock, which is needed for RFBI to
calculate timings
- dss_dsi is missing ick and sys_clk
- dss_venc is missing dss_96m_fck opt-clock, which is required on
OMAP3430
- dss_venc's interface and main clocks are wrong, causing VENC to fail
to start
These problems were temporarily fixed with a DSS patch
9ede365aa6 ("HACK: OMAP: DSS2: clk hack
for OMAP2/3"), which can be reverted after this patch (and the similar
patches for other OMAPs).
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
DSS needs all DSS clocks to be enabled to be able to finish reset
properly. Before v3.1-rc1 the omapdss driver was managing clocks and
resets correctly. However, when omapdss started using runtime PM at
v3.1-rc1, the responsibility for the reset moved to HWMOD framework.
HWMOD framework does not currently enable all the DSS clocks when
resetting the DSS hardware. This hasn't caused any problems so far, but
we may just have been lucky.
dss_core's opt-clocks is also missing dss_96m_fck, which is a DSS clock
present only on OMAP3430, and thus required on OMAP3430 to finish the
reset.
This patch sets HWMOD_CONTROL_OPT_CLKS_IN_RESET and adds the dss_96m_fck
opt-clock for dss_core in OMAP3 HWMOD data, fixing the issue.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
[paul@pwsan.com: merged duplicate .flags fields]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Commit d6504acd21 ("OMAP2+: hwmod:
remove OMAP_CHIP*") tests the inverse condition of what it should be
testing for the return value from omap_hwmod_register(). This causes
several IP blocks to not be registered on several OMAP3 family devices.
Fixing that bug also unmasked another bug, originally reported by
Chase Maupin <chase.maupin@ti.com> and then subsequently by Abhilash K
V <abhilash.kv@ti.com>, which caused SmartReflex IP blocks to be
registered on SoCs that don't support them.
Thanks to Russell King - ARM Linux <linux@arm.linux.org.uk> for comments
on a previous version of the patch.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Chase Maupin <chase.maupin@ti.com>
Cc: Abhilash K V <abhilash.kv@ti.com>
Cc: Russell King - ARM Linux <linux@arm.linux.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
* 'next/pm' of git://git.linaro.org/people/arnd/arm-soc: (66 commits)
ARM: CSR: PM: use outer_resume to resume L2 cache
ARM: CSR: call l2x0_of_init to init L2 cache of SiRFprimaII
ARM: OMAP: voltage: voltage layer present, even when CONFIG_PM=n
ARM: CSR: PM: add sleep entry for SiRFprimaII
ARM: CSR: PM: save/restore irq status in suspend cycle
ARM: CSR: PM: save/restore timer status in suspend cycle
OMAP4: PM: TWL6030: add cmd register
OMAP4: PM: TWL6030: fix ON/RET/OFF voltages
OMAP4: PM: TWL6030: address 0V conversions
OMAP4: PM: TWL6030: fix uv to voltage for >0x39
OMAP4: PM: TWL6030: fix voltage conversion formula
omap: voltage: add a stub header file for external/regulator use
OMAP2+: VC: more registers are per-channel starting with OMAP5
OMAP3+: voltage: update nominal voltage in voltdm_scale() not VC post-scale
OMAP3+: voltage: rename omap_voltage_get_nom_volt -> voltdm_get_voltage
OMAP3+: voltdm: final removal of omap_vdd_info
OMAP3+: voltage: move/rename curr_volt from vdd_info into struct voltagedomain
OMAP3+: voltage: rename scale and reset functions using voltdm_ prefix
OMAP3+: VP: combine setting init voltage into common function
OMAP3+: VP: remove unused omap_vp_get_curr_volt()
...
Fix up trivial conflict in arch/arm/mach-prima2/l2x0.c (code removal vs
edit)
Removing modules iva, sr1_hwmod, sr2_hwmod, mailbox from
the base omap3xxx_hwmods list, so that they can be excluded
for am35x. This removes quite a few warnings on boot for AM35x.
Signed-off-by: Abhilash K V <abhilash.kv@ti.com>
[paul@pwsan.com: dropped 'mailbox class' comments; updated changelog]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add routines to converts dmtimers to platform devices. The device data
is obtained from hwmod database of respective platform and is registered
to device model after successful binding to driver.
In addition, capability attribute of each of the timers is added in
hwmod database.
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Signed-off-by: Thara Gopinath <thara@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Cousson, Benoit <b-cousson@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Linus Torvalds
Paul Walmsley
Mark A. Greer
Tony Lindgren
Peter Ujfalusi
Kevin Hilman
Jon Hunter
Jean Pihet
Olof Johansson
Vaibhav Hiremath
Archit Taneja
Nishanth Menon
Shweta Gulati
Ilya Yanok
Tomi Valkeinen
Shubhrajyoti D
Keshava Munegowda
Kyle Manna
Aaro Koskinen
Felipe Contreras
Abhilash K V
Tarun Kanti DebBarma