Add a platform-device to scx200_gpio, and use its struct device dev member
(ie: devp) in dev_dbg() once.
There are 2 alternatives here (Im soliciting guidance/commentary):
- use isa_device, if/when its added to the kernel.
- alter scx200.c to EXPORT_GPL its private devp so that both scx200_gpio,
and the (to be added) nsc_gpio module can use it. Since the available devp
is in 'grandparent', this seems like too much 'action at a distance'.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Adopt many modern 2.6 coding practices, ala LDD3, chapter 3. Changes are
limited to initialization calls from module init, ie: cdev_init, cdev_add,
*_chrdev_region, mkdev.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
GPIO SUPPORT FOR SCx200 & PC8736x
The patch-set reworks the 2.4 vintage scx200_gpio driver for modern 2.6, and
refactors GPIO support to reuse it in a new driver for the GPIO on PC-8736x
chips. Its handy for the Soekris.com net-4801, which has both chips.
These patches have been seen recently on Kernel-Mentors, and then
Kernel-Newbies ML, where Jesper Juhl kindly reviewed it. His feedback has
been incorporated. Thanks Jesper !
Its also gone to soekris-tech@soekris.com for possible testing by linux folks,
I've gotten 1 promise so far. Theyre mostly BSD folk over there, but we'll
see..
Device-file & Sysfs
The driver preserves the existing device-file interface, including the
write/cmd set, but adds v to 'view' the pin-settings & configs by inducing,
via gpio_dump(), a dev_info() call. Its a fairly crappy way to get status,
but it sticks to the syslog approach, conservatively.
Allowing users to voluntarily trigger logging is good, it gives them a
familiar way to confirm their app's control & use of the pins, and I've thus
reduced the pin-mode-updates from dev_info to dev_dbg.
I've recently bolted on a proto sysfs interface for both new drivers. Im not
including those patches here; they (the patch + doc-pre-patch) are still quite
raw (and unreviewed on KNML), and since they 'invent' a convention for GPIO, a
proper vetting is needed. Since this patchset is much bigger than my previous
ones, Id like to keep things simpler, and address it 1st, before bolting on
more stuff.
The driver-split
The Geode CPU and the PC-87366 Super-IO chip have GPIO units which share a
common pin-architecture (same pin features, with same bits controlling), but
with different addressing mechanics and port organizations.
The vintage driver expresses the pin capabilities with pin-mode commands
[OoPpTt],etc that change the pin configurations, and since the 2 chips share
pin-arch, we can reuse the read(), write() commands, once the implementation
is suitably adjusted.
The patchset adds a vtable: struct nsc_gpio_ops, to abstract the existing gpio
operations, then adjusts fileops.write() code to invoke operations via that
vtable. Driver specific open()s set private_data to the vtable so its
available for use by write().
The vtable gets the gpio_dump() too, since its user-friendly, and (could be
construed as) part of the current device-file interface. To support use of
dev_dbg() in write() & _dump(), the vtable gets a dev ptr too, set by both
scx200 & pc8736x _gpio drivers.
heres how the pins are presented in syslog:
[ 1890.176223] scx200_gpio.0: io00: 0x0044 TS OD PUE EDGE LO DEBOUNCE
[ 1890.287223] scx200_gpio.0: io01: 0x0003 OE PP PUD EDGE LO
nsc_gpio.c: new file is new home of several file-ops methods, which are
modified to get their vtable from filp->private_data, and use it where needed.
scx200_gpio.c: keeps some of its existing gpio routines, but now wires them up
via the vtable (they're invoked by nsc_gpio.c:nsc_gpio_write() thru this
vtable). A driver-spcific open() initializes filp->private_data with the
vtable.
Once the split is clean, and the scx200_gpio driver is working, we copy and
modify the function and variable names, and rework the access-method bodies
for the different addressing scheme.
Heres a working overview of the patchset:
# series file for GPIO
# Spring Cleaning
gpio-scx/patch.preclean # scripts/Lindent fixes, editor-ctrl comments
# API Modernization
gpio-scx/patch.api26 # what I learned from LDD3
gpio-scx/patch.platform-dev-2 # get pdev, support for dev_dbg()
gpio-scx/patch.unsigned-minor # fix to match std practice
# Debuggability
gpio-scx/patch.dump-diet # shrink gpio_dump()
gpio-scx/patch.viewpins # add new 'command' to call dump()
gpio-scx/patch.init-refactor # pull shadow-register init to sub
# Access-Abstraction (add vtable)
gpio-scx/patch.access-vtable # introduce nsg_gpio_ops vtable, w dump
gpio-scx/patch.vtable-calls # add & use the vtable in scx200_gpio
gpio-scx/patch.nscgpio-shell # add empty driver for common-fops
# move code under abstraction
gpio-scx/patch.migrate-fops # move file-ops methods from scx200_gpio
gpio-scx/patch.common-dump # mv scx200.c:scx200_gpio_dump() to nsc_gpio.c
gpio-scx/patch.add-pc8736x-gpio # add new driver, like old, w chip adapt
# gpio-scx/patch.add-DEBUG # enable all dev_dbg()s
# Cleanups
# finish printk -> dev_dbg() etc
gpio-scx/patch.pdev-pc8736x # new drvr needs pdev too,
gpio-scx/patch.devdbg-nscgpio # add device to 'vtable', use in dev_dbg()
# gpio-scx/patch.pin-config-view # another 'c' 'command'
# gpio-scx/quiet-getset # take out excess dbg stuff (pretty quiet
now)
gpio-scx/patch.shadow-current # imitate scx200_gpio's shadow regs in
pc87*
# post KMentors-post patches ..
gpio-scx/patch.mutexes # use mutexes for config-locks
gpio-scx/patch.viewpins-values # extend dump to obsolete separate 'c' cmd
gpio-scx/patch.kconfig # add stuff for kbuild
# TBC
# combine api26 with pdev, which is just one step.
# merge c&v commands to single do-all-fn
# delay viewpins, dump-diet should also un-ifdef it too.
diff.sys-gpio-rollup-1
This patch:
Removed editor format-control comments, and used scripts/Lindent to clean up
whitespace, then deleted the bogus chunks :-(
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make notifier_blocks associated with cpu_notifier as __cpuinitdata.
__cpuinitdata makes sure that the data is init time only unless
CONFIG_HOTPLUG_CPU is defined.
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Cc: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
CPUs come online only at init time (unless CONFIG_HOTPLUG_CPU is defined).
So, cpu_notifier functionality need to be available only at init time.
This patch makes register_cpu_notifier() available only at init time, unless
CONFIG_HOTPLUG_CPU is defined.
This patch exports register_cpu_notifier() and unregister_cpu_notifier() only
if CONFIG_HOTPLUG_CPU is defined.
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Cc: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In 2.6.17, there was a problem with cpu_notifiers and XFS. I provided a
band-aid solution to solve that problem. In the process, i undid all the
changes you both were making to ensure that these notifiers were available
only at init time (unless CONFIG_HOTPLUG_CPU is defined).
We deferred the real fix to 2.6.18. Here is a set of patches that fixes the
XFS problem cleanly and makes the cpu notifiers available only at init time
(unless CONFIG_HOTPLUG_CPU is defined).
If CONFIG_HOTPLUG_CPU is defined then cpu notifiers are available at run
time.
This patch reverts the notifier_call changes made in 2.6.17
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Cc: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We need to serialize access to the global rtc_idr even in this error path.
Signed-off-by: Sonny Rao <sonny@burdell.org>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There are two locking sets involved. One locks the board mappings and the
other is the tty open/close locking. The low level code was clearly
designed to be ported to OS's with spin locks already so pretty much comes
out in the wash
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Corey Minyard <minyard@acm.org>
The kthread used to speed up polling for IPMI was using udelay in its
busy-wait polling loop when the lower-level state machine told it to do a
short delay. This just used CPU and didn't help scheduling, thus causing
bad problems with other tasks. Call schedule() instead.
Signed-off-by: Corey Minyard <minyard@acm.org>
Acked-by: Matt Domsch <Matt_Domsch@dell.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix TCSBRK comment to prevent confusion or accidental removal.
Signed-off-by: Paul Fulghum <paulkf@microgate.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
locking init cleanups:
- convert " = SPIN_LOCK_UNLOCKED" to spin_lock_init() or DEFINE_SPINLOCK()
- convert rwlocks in a similar manner
this patch was generated automatically.
Motivation:
- cleanliness
- lockdep needs control of lock initialization, which the open-coded
variants do not give
- it's also useful for -rt and for lock debugging in general
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Update two drivers to use poison.h.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Localize poison values into one header file for better documentation and
easier/quicker debugging and so that the same values won't be used for
multiple purposes.
Use these constants in core arch., mm, driver, and fs code.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Acked-by: Matt Mackall <mpm@selenic.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
With Goto-san's patch, we can add new pgdat/node at runtime. I'm now
considering node-hot-add with cpu + memory on ACPI.
I found acpi container, which describes node, could evaluate cpu before
memory. This means cpu-hot-add occurs before memory hot add.
In most part, cpu-hot-add doesn't depend on node hot add. But register_cpu(),
which creates symbolic link from node to cpu, requires that node should be
onlined before register_cpu(). When a node is onlined, its pgdat should be
there.
This patch-set holds off creating symbolic link from node to cpu
until node is onlined.
This removes node arguments from register_cpu().
Now, register_cpu() requires 'struct node' as its argument. But the array of
struct node is now unified in driver/base/node.c now (By Goto's node hotplug
patch). We can get struct node in generic way. So, this argument is not
necessary now.
This patch also guarantees add cpu under node only when node is onlined. It
is necessary for node-hot-add vs. cpu-hot-add patch following this.
Moreover, register_cpu calculates cpu->node_id by cpu_to_node() without regard
to its 'struct node *root' argument. This patch removes it.
Also modify callers of register_cpu()/unregister_cpu, whose args are changed
by register-cpu-remove-node-struct patch.
[Brice.Goglin@ens-lyon.org: fix it]
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: Ashok Raj <ashok.raj@intel.com>
Cc: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Brice Goglin <Brice.Goglin@ens-lyon.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When new node becomes enable by hot-add, new sysfs file must be created for
new node. So, if new node is enabled by add_memory(), register_one_node() is
called to create it. In addition, I386's arch_register_node() and a part of
register_nodes() of powerpc are consolidated to register_one_node() as a
generic_code().
This is tested by Tiger4(IPF) with node hot-plug emulation.
Signed-off-by: Keiichiro Tokunaga <tokuanga.keiich@jp.fujitsu.com>
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is to find node id from acpi's handle of memory_device in DSDT. _PXM for
the new node can be found by acpi_get_pxm() by using new memory's handle. So,
node id can be found by pxm_to_nid_map[].
This patch becomes simpler than v2 of node hot-add patch.
Because old add_memory() function doesn't have node id parameter.
So, kernel must find its handle by physical address via DSDT again.
But, v3 just give node id to add_memory() now.
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: Dave Hansen <haveblue@us.ibm.com>
Cc: "Brown, Len" <len.brown@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Change the name of old add_memory() to arch_add_memory. And use node id to
get pgdat for the node at NODE_DATA().
Note: Powerpc's old add_memory() is defined as __devinit. However,
add_memory() is usually called only after bootup.
I suppose it may be redundant. But, I'm not well known about powerpc.
So, I keep it. (But, __meminit is better at least.)
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: Dave Hansen <haveblue@us.ibm.com>
Cc: "Brown, Len" <len.brown@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When acpi_memory_device_init() is called at boottime to register struct
memory acpi_memory_device, acpi_bus_add() are called via
acpi_driver_attach().
But it also calls ops->start() function. It is called even if the memory
blocks are initialized at early boottime. In this case add_memory() return
-EEXIST, and the memory blocks becomes INVALID state even if it is normal.
This is patch to avoid calling add_memory() for already available memory.
[akpm@osdl.org: coding cleanups]
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: "Brown, Len" <len.brown@intel.com>
Cc: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is a patch to call add_memroy() when notify reaches for new node's add
event.
When new node is added, notify of ACPI reaches container device which means
the node.
Container device driver calls acpi_bus_scan() to find and add belonging
devices (which means cpu, memory and so on). Its function calls add and
start function of belonging devices's driver.
Howevever, current memory hotplug driver just register add function to
create sysfs file for its memory. But, acpi_memory_enable_device() is not
called because it is considered just the case that notify reaches memory
device directly. So, if notify reaches container device nothing can call
add_memory().
This is a patch to create start function which calls add_memory().
add_memory() can be called by this when notify reaches container device.
[akpm@osdl.org: coding cleanups]
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: "Brown, Len" <len.brown@intel.com>
Cc: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Current acpi memory hotplug just looks into the first entry of resources in
_CRS. But, _CRS can contain plural resources. So, if _CRS contains plural
resoureces, acpi memory hot add cannot add all memory.
With this patch, acpi memory hotplug can deal with Memory Device, whose
_CRS contains plural resources.
Tested on ia64 memory hotplug test envrionment (not emulation, uses alpha
version firmware which supports dynamic reconfiguration of NUMA.)
Note: Microsoft's Windows Server 2003 requires big (>4G)resoureces to be
divided into small (<4G) resources. looks crazy, but not invalid.
(See http://www.microsoft.com/whdc/system/pnppwr/hotadd/hotaddmem.mspx)
For this reason, a firmware vendor who supports Windows writes plural
resources in a _CRS even if they are contiguous.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: "Brown, Len" <len.brown@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add a helper to asm/pdc.h to translate OS_ID values to strings
and use it in the pdc_stable driver.
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
We were assigned an OS_ID of 0x0006. Consistently use OS_ID_LINUX
instead of using the magic number. Also update the OS_ID_ defines in
asm/pdc.h to reflect this.
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
pdc_stable v0.30:
This patch introduces 3 more files to the /sys/firmware/stable tree:
- diagnostic, which contains a cryptic hex string
- osdep1, a 16 bytes os-dependent storage area always available
- osdep2, another os-dependent storage area which existence/size depends
on hversion.
This patch also adds code to setup the "Linux" signature in stable
storage. That is to say that starting with this patch, the kernel will
now sign its OSID (0x0006, thx LaMont) in Stable Storage upon boot,
whether pdc_stable is enabled or not.
Signed-off-by: Thibaut VARENE <varenet@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
This patch removes a limitation of the original code, so that CHASSIS
codes can be sent to all machines. On machines with a LCD panel, this
code displays "INI" during bootup, "RUN" when the system is booted and
running, "FLT" when a panic occurs, etc.
This part of the code can be enabled/disabled through CONFIG_PDC_CHASSIS
This patch also adds minimalistic support for Chassis warnings, through
a proc entry '/proc/chassis', which will reflect the warnings status (PSU
or fans failure when they happen, NVRAM battery level and temperature
thresholds overflows).
This part of the code can be enabled/disabled through CONFIG_PDC_CHASSIS_WARN
Signed-off-by: Thibaut VARENE <varenet@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Some debugging code in sba_iommu.c should be testing ioc_needs_fdc,
not directly testing boot_cpu_data.
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Clean up gcc 4.1 warnings noted by Joel Soete.
Kyle McMartin gets kudos for pointing out the issues.
Matthew Wilcox noticed sba_iommu was using open coded versions
of (read|write)X.
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
The other way round works not really well with boards which have a
static NAND chipselect.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Allow lseek(mtdchar_fd, 0, SEEK_END) to succeed, which currently fails
with EINVAL.
lseek(fd, 0, SEEK_END) should result into the same fileposition as
lseek(fd, 0, SEEK_SET) + read(fd, buf, length(fd))
Furthermore, lseek(fd, 0, SEEK_CUR) should return the current file position,
which in case of an encountered EOF should not result in EINVAL
Signed-off-by: Herbert Valerio Riedel <hvr@gnu.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
I was unable to compile ts7250.c after your refactor commit,
it's a typo probably.
-- ynezz
From: Petr Stetiar <ynezz@true.cz>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
It should be done before calling class_device_unregister() because
it will destroy the device and free memory if there are no other
references to the device.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Based on a patch series originally from Vivek Goyal <vgoyal@in.ibm.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Based on a patch series originally from Vivek Goyal <vgoyal@in.ibm.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Based on a patch series originally from Vivek Goyal <vgoyal@in.ibm.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is needed if we wish to change the size of the resource structures.
Based on an original patch from Vivek Goyal <vgoyal@in.ibm.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is needed if we wish to change the size of the resource structures.
Based on an original patch from Vivek Goyal <vgoyal@in.ibm.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is needed if we wish to change the size of the resource structures.
Based on an original patch from Vivek Goyal <vgoyal@in.ibm.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is needed if we wish to change the size of the resource structures.
Based on an original patch from Vivek Goyal <vgoyal@in.ibm.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is needed if we wish to change the size of the resource structures.
Based on an original patch from Vivek Goyal <vgoyal@in.ibm.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is needed if we wish to change the size of the resource structures.
Based on an original patch from Vivek Goyal <vgoyal@in.ibm.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is needed if we wish to change the size of the resource structures.
Based on an original patch from Vivek Goyal <vgoyal@in.ibm.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Based on an original patch from Ralf Baechle <ralf@linux-mips.org> and
Vivek Goyal <vgoyal@in.ibm.com>. This is needed in order to prepare for
changing the size of resources.
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes a simple off-by-one error in the mtd physmap driver.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Add support for both the S3C2412 and S3C2412 Samsung SoCs to
the increasingly mis-named s3c2410.c driver.
This currently only supports SLC ECCs, and a chip on nFCE0.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Wistron MS 2111 (aka Medion 'Titanium' MD 9783, aka ALDI PC,
aka Fujitsu-Siemens AMILO D7800, aka ...) has 5 extra buttons,
map them. Unfortunately we only have DMI data for the Medion
box.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
print kobj name in this message.
lenb changed to use printk.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
The ASL Acquire operator (17.5.1 in ACPI 3.0 spec) is allowed to time out
and return True without acquiring the semaphore. There's no indication in
the spec that this is an actual error, so this message should be
debug-only, as the message for successful acquisition is.
This used to be an ACPI_DEBUG_PRINT, but it was mis-classified as
ACPI_DB_ERROR rather than ACPI_DB_MUTEX, so it got swept up in Thomas'
recent patch to enable ACPI error messages even without CONFIG_ACPI_DEBUG.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Symbols such as PCI_USES_IO, PCI_ADDR0, etc. originated from Donald
Becker's net driver template, but have been long unused. Remove.
In a few drivers, this allows the further eliminate of the pci_flags (or
just plain flags) member in the template driver probe structure.
Most of this logic is simply open-coded in most drivers, since it never
changes.
Made a few other cleanups while I was in there, too:
* constify, __devinitdata several PCI ID tables
* replace table terminating entries such as "{0,}," and "{NULL},"
with a more-clean "{ }".
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch makes two needlessly global functions static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
A card number is not unique enough. Instead, let the caller specify the
prefix of the status messages.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
For most tuners the default TOP value is 0x10, regardless of TV norm.
So revert earlier change that sets the TOP value to 0x14 for PAL/SECAM.
This is incorrect.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Format description was cut off. It's been shortened.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Remove the duplicate '(tda9887)' in these messages:
tda9887 8-0043 (tda9887): tda988[5/6/7] found @ 0x43 (tuner)
The same string is already printed as the prefix in this line.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
implemented VIDIOC_LOG_STATUS in the cx88-blackbird driver
to show the status of i2c clients and the cx23416 mpeg encoder.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Implement V4L2 driver for the Hauppauge PVR USB2 TV tuner.
The Hauppauge PVR USB2 is a USB connected TV tuner with an embedded
cx23416 hardware MPEG2 encoder. There are two major variants of this
device; this driver handles both. Any V4L2 application which
understands MPEG2 video stream data should be able to work with this
device.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
* make eeprom size a variable, prepping for future patch
* eliminate unused PCI_xxx stuff left over from Becker driver template
* convert a few #defines to enum
* mark PCI table const, __devinitdata
* don't bother with named constant for PCI device id
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Updates generic HDLC info page address, I should have done it
long time ago.
Signed-off-by: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
dev_setup() is using the __initdata variables ax25_broadcast and
ax25_test.
Since the only caller of dev_setup() (setup_adapter()) is already
__init, the solution is to make dev_setup() __init, too.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
From: Uwe Zeisberger <Uwe_Zeisberger@digi.com>
The phy ids used are taken from an driver that used a right shift of 4 to chop
off the revision number. This driver does not shift, so the id and mask
values are wrong and must be left shifted by 4 to actually detect the chips.
Signed-off-by: Uwe Zeisberger <Uwe_Zeisberger@digi.com>
Acked-by: Andy Fleming <afleming@freescale.com>
[akpm: this is a previously-nacked patch, but the problem is real]
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Ensure the driver's module owner field is
initialised for when this is being built and
loaded as a module.
Also change make the dm9000_tx_done function
static, as it is not exported elsewhere.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The DM9000 initialisation sequence for the
hardware re-initialise the board spin-lock,
which is in my view wrong.
This patch removes the extra spin lock
initialisation
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The DM9000 driver does not deal with the case
where there is no serial EEPROM to store the
configuration, and the bootloader has placed
an MAC address into the device already.
If there is no valid MAC in the EEPROM, read
the one already in the chip and check to see
if that one is valid.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The current DM9000 driver cannot cope if it
is given more than 3 resources (for example, if
it is being passed an wake-up irq that it is
not using yet).
Check that we have been given at-least one IRQ
resource.
Also fix the minor type-casting for the case
of 2 resources.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Ata_piix's Kconfig entry still refers only to ICH5, while it supports ICH6
through 8. This creates confusion with people who are looking to see
if their newer SATA enabled motherboards are supported. The
following patch makes this clear.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Some SATA controllers embedded in ATI IXPs seem to have broken
SATA_IRQ bit in their bmdma2 registers which is always stuck at 1.
This makes the driver believe that there has been a hotplug event and
freeze the port whenever there's an interrupt thus failing all
commands.
This patch disables SATA_IRQ for those controllers.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Cosmetic updates in libata-core.c.
* trim trailing whitespaces
* break lines which are over 80 column
* kill unnecessary braces
* make indentation consistent
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
From: Andrew Morton <akpm@osdl.org>
Provide a module parameter to override the default 30-second-per-device SATA
probing timeout.
Cc: Tejun Heo <htejun@gmail.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Make ata_do_simple_cmd() and ata_flush_cache() global. These will be
used from libata-eh.c.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* the function has always returned AC_ERR_* masks not -errno but its
return type was int. Make return type unsigned int.
* don't print error message automatically. it's the caller's
responsibility.
* add header comment
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Clear related EH action on device detach such that new device doesn't
receive EH actions scheduled for the old one.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Implement and use ata_eh_dev_action() which returns EH action mask for
a device.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Partially revert 74d0a988d3aa359b6b8a8536c8cb92cce02ca5d5:
[PATCH] PCI: Move various PCI IDs to header file
libata policy is to avoid use of named PCI device ID constants.
These are often single-use constants, which have little value over
direct numeric constants save for constant include/linux/pci_ids.h
patching/merging headaches.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Mark Bellon found a bug in my tlclk driver. Thanks!
I botch the register mask for store_received_ref_clk3a.
See http://download.intel.com/design/network/manuals/30412001.pdf
tables 124 and 136 for details.
Signed-off-by: Mark Gross <mark.gross@intel.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/bunk/trivial:
typo fixes
Clean up 'inline is not at beginning' warnings for usb storage
Storage class should be first
i386: Trivial typo fixes
ixj: make ixj_set_tone_off() static
spelling fixes
fix paniced->panicked typos
Spelling fixes for Documentation/atomic_ops.txt
move acknowledgment for Mark Adler to CREDITS
remove the bouncing email address of David Campbell
The changes in the tty handling contain a bug while accessing
the last byte in the skb. Since special sequence for control of
DTMF and FAX via ttyI* devices handled via this path, these services
do not work anymore.
Signed-off-by: Karsten Keil <kkeil@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I've always found this flag confusing. Now that devfs is no longer around, it
has been renamed, and the documentation for when this flag should be used has
been updated.
Also fixes all drivers that use this flag.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This was spotted by coverity #id 1300. Since the array has only four
elements, we should just use those four.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Acked-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This reverts commit c7b2eff059.
Hugh Dickins explains:
"It seems too little tested: "losetup -d /dev/loop0" fails with
EINVAL because nothing sets lo_thread; but even when you patch
loop_thread() to set lo->lo_thread = current, it can't survive
more than a few dozen iterations of the loop below (with a tmpfs
mounted on /tst):
j=0
cp /dev/zero /tst
while :
do
let j=j+1
echo "Doing pass $j"
losetup /dev/loop0 /tst/zero
mkfs -t ext2 -b 1024 /dev/loop0 >/dev/null 2>&1
mount -t ext2 /dev/loop0 /mnt
umount /mnt
losetup -d /dev/loop0
done
it collapses with failed ioctl then BUG_ON(!bio).
I think the original lo_done completion was more subtle and safe
than the kthread conversion has allowed for."
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild: (40 commits)
kbuild: trivial fixes in Makefile
kbuild: adding symbols in Kconfig and defconfig to TAGS
kbuild: replace abort() with exit(1)
kbuild: support for %.symtypes files
kbuild: fix silentoldconfig recursion
kbuild: add option for stripping modules while installing them
kbuild: kill some false positives from modpost
kbuild: export-symbol usage report generator
kbuild: fix make -rR breakage
kbuild: append -dirty for updated but uncommited changes
kbuild: append git revision for all untagged commits
kbuild: fix module.symvers parsing in modpost
kbuild: ignore make's built-in rules & variables
kbuild: bugfix with initramfs
kbuild: modpost build fix
kbuild: check license compatibility when building modules
kbuild: export-type enhancement to modpost.c
kbuild: add dependency on kernel.release to the package targets
kbuild: `make kernelrelease' speedup
kconfig: KCONFIG_OVERWRITECONFIG
...
* master.kernel.org:/pub/scm/linux/kernel/git/mchehab/v4l-dvb:
V4L/DVB (4227): Update this driver for recent header file movement.
V4L/DVB (4223): Add V4L2_CID_MPEG_STREAM_VBI_FMT control
V4L/DVB (4222): Always switch tuner mode when calling VIDIOC_S_FREQUENCY.
V4L/DVB (4221): Add HM12 YUV format define.
V4L/DVB (4219): Av7110: analog sound output of DVB-C rev 2.3
V4L/DVB (4217): Fix a misplaced closing bracket/else, which caused swzigzag not to be called
V4L/DVB (4215): Make VIDEO_CX88_BLACKBIRD a separate build option
V4L/DVB (4214): Make VIDEO_CX2341X a selectable build option
V4L/DVB (4213): Cx88: cleanups
V4L/DVB (4211): Fix an Oops for all fe that have get_frontend_algo == NULL
CC drivers/pci/msi-apic.o
In file included from include/asm/msi.h:11,
from drivers/pci/msi.h:71,
from drivers/pci/msi-apic.c:8:
include/asm/smp.h:103: error: syntax error before '->' token
akpm: nasty. It appears to be
static inline unsigned int cpu_mask_to_apicid(cpumask_t cpumask)
conflicting with include/asm-x86_64/mach_apic.h's
#define cpu_mask_to_apicid (genapic->cpu_mask_to_apicid)
And I don't know which patch in rc4-mm1 triggered this.
Fixing this in the .c file seems wrong.
Including asm/smp.h instead of linux/smp.h seems wrong too. Need that
.config.
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
During some profiling I noticed that default_idle causes a lot of
memory traffic. I think that is caused by the atomic operations
to clear/set the polling flag in thread_info. There is actually
no reason to make this atomic - only the idle thread does it
to itself, other CPUs only read it. So I moved it into ti->status.
Converted i386/x86-64/ia64 for now because that was the easiest
way to fix ACPI which also manipulates these flags in its idle
function.
Cc: Nick Piggin <npiggin@novell.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Rename the GART_IOMMU option to IOMMU to make clear it's not
just for AMD
- Rewrite the help text to better emphatise this fact
- Make it an embedded option because too many people get it wrong.
To my astonishment I discovered the aacraid driver tests this
symbol directly. This looks quite broken to me - it's an internal
implementation detail of the PCI DMA API. Can the maintainer
please clarify what this test was intended to do?
Cc: linux-scsi@vger.kernel.org
Cc: alan@redhat.com
Cc: markh@osdl.org
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Factor out the duplicated access/cache code into a single file
* Shared between i386/x86-64.
- Share flush code between AGP and IOMMU
* Fix a bug: AGP didn't wait for end of flush before
- Drop 8 northbridges limit and allocate dynamically
- Add lock to serialize AGP and IOMMU GART flushes
- Add PCI ID for next AMD northbridge
- Random related cleanups
The old K8 NUMA discovery code is unchanged. New systems
should all use SRAT for this.
Cc: "Navin Boppuri" <navin.boppuri@newisys.com>
Cc: Dave Jones <davej@redhat.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
[SPARC]: Add iomap interfaces.
[OPENPROM]: Rewrite driver to use in-kernel device tree.
[OPENPROMFS]: Rewrite using in-kernel device tree and seq_file.
[SPARC]: Add unique device_node IDs and a ".node" property.
[SPARC]: Add of_set_property() interface.
[SPARC64]: Export auxio_register to modules.
[SPARC64]: Add missing interfaces to dma-mapping.h
[SPARC64]: Export _PAGE_IE to modules.
[SPARC64]: Allow floppy driver to build modular.
[SPARC]: Export x_bus_type to modules.
[RIOWATCHDOG]: Fix the build.
[CPWATCHDOG]: Fix the build.
[PARPORT] sunbpp: Fix typo.
[MTD] sun_uflash: Port to new EBUS device layer.
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6: (42 commits)
[IOAT]: Do not dereference THIS_MODULE directly to set unsafe.
[NETROM]: Fix possible null pointer dereference.
[NET] netpoll: break recursive loop in netpoll rx path
[NET] netpoll: don't spin forever sending to stopped queues
[IRDA]: add some IBM think pads
[ATM]: atm/mpc.c warning fix
[NET]: skb_find_text ignores to argument
[NET]: make net/core/dev.c:netdev_nit static
[NET]: Fix GSO problems in dev_hard_start_xmit()
[NET]: Fix CHECKSUM_HW GSO problems.
[TIPC]: Fix incorrect correction to discovery timer frequency computation.
[TIPC]: Get rid of dynamically allocated arrays in broadcast code.
[TIPC]: Fixed link switchover bugs
[TIPC]: Enhanced & cleaned up system messages; fixed 2 obscure memory leaks.
[TIPC]: First phase of assert() cleanup
[TIPC]: Disallow config operations that aren't supported in certain modes.
[TIPC]: Fixed memory leak in tipc_link_send() when destination is unreachable
[TIPC]: Added missing warning for out-of-memory condition
[TIPC]: Withdrawing all names from nameless port now returns success, not error
[TIPC]: Optimized argument validation done by connect().
...
Usually we don't care much about 'gcc -W' warnings, but some of us do build
kernels that way to look for problems, and then the fewer warnings we have
to wade through the better. Especially when they are very easy and
non-intrusive to clean up. Which is the case for the following warnings
spewed by drivers/usb/storage/usb.h :
drivers/usb/storage/usb.h:163: warning: `inline' is not at beginning of
+declaration
drivers/usb/storage/usb.h:166: warning: `inline' is not at beginning of
+declaration
There's also some precedence for cleaning up these warnings. I've had
a few patches merged in the past that remove exactly this class of
warnings.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Make needlessly global code static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It appears in /sys/mdX/md/dev-YYY/state
and can be set or cleared by writing 'writemostly' or '-writemostly'
respectively.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The md/dev-XXX/state file can now be written:
"faulty" simulates an error on the device
"remove" removes the device from the array (if it is not busy)
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This allows the state of an md/array to be directly controlled via sysfs and
adds the ability to stop and array without tearing it down.
Array states/settings:
clear
No devices, no size, no level
Equivalent to STOP_ARRAY ioctl
inactive
May have some settings, but array is not active
all IO results in error
When written, doesn't tear down array, but just stops it
suspended (not supported yet)
All IO requests will block. The array can be reconfigured.
Writing this, if accepted, will block until array is quiescent
readonly
no resync can happen. no superblocks get written.
write requests fail
read-auto
like readonly, but behaves like 'clean' on a write request.
clean - no pending writes, but otherwise active.
When written to inactive array, starts without resync
If a write request arrives then
if metadata is known, mark 'dirty' and switch to 'active'.
if not known, block and switch to write-pending
If written to an active array that has pending writes, then fails.
active
fully active: IO and resync can be happening.
When written to inactive array, starts with resync
write-pending (not supported yet)
clean, but writes are blocked waiting for 'active' to be written.
active-idle
like active, but no writes have been seen for a while (100msec).
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- record the 'event' count on each individual device (they
might sometimes be slightly different now)
- add a new value for 'sb_dirty': '3' means that the super
block only needs to be updated to record a clean<->dirty
transition.
- Prefer odd event numbers for dirty states and even numbers
for clean states
- Using all the above, don't update the superblock on
a spare device if the update is just doing a clean-dirty
transition. To accomodate this, a transition from
dirty back to clean might now decrement the events counter
if nothing else has changed.
The net effect of this is that spare drives will not see any IO requests
during normal running of the array, so they can go to sleep if that is what
they want to do.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When an array has a bitmap, a device can be removed and re-added and only
blocks changes since the removal (as recorded in the bitmap) will be resynced.
It should be possible to do a similar thing to arrays without bitmaps. i.e.
if a device is removed and re-added and *no* changes have been made in the
interim, then the add should not require a resync.
This patch allows that option. This means that when assembling an array one
device at a time (e.g. during device discovery) the array can be enabled
read-only as soon as enough devices are available, but extra devices can still
be added without causing a resync.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
As data_disks is *less* than raid_disks, the current test here is obviously
wrong. And as the difference is already available in conf->max_degraded, it
makes much more sense to use that.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
RAID5 recently changed to RAID456
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I was experimenting with Linux SW raid today and found a spelling error when
reading the help menus... (and fly spell found more).
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Jim Cromie
Chandra Seetharaman
Sonny Rao
Alan Cox
akpm@osdl.org
Paul Fulghum
Atsushi Nemoto
Ingo Molnar
Randy Dunlap
KAMEZAWA Hiroyuki
Yasunori Goto
Kyle McMartin
Thibaut Varene
Grant Grundler
Thomas Gleixner
Herbert Valerio Riedel
Petr Stetiar
Dmitry Torokhov
Greg Kroah-Hartman
Sascha Hauer
Lennert Buytenhek
Ben Dooks
Frank de Lange
Thomas Renninger
Patrick Mochel
Len Brown
Jae-hyeon Park
Bjorn Helgaas
Jeff Garzik
Mauro Carvalho Chehab
Adrian Bunk
Hans Verkuil
Mike Isely
Michael Krufky
Mike Isely
Krzysztof Halasa
Uwe Zeisberger
Ben Dooks
Auke Kok
Tejun Heo
Randy Dunlap
Linus Torvalds
mark gross
Karsten Keil
Eric Sesterhenn
Christian Kujau
Andi Kleen
Jesper Juhl
NeilBrown
Justin Piszcz